Search Documents

By D. R. Conlon, E. R. Brownscombe

Errors in measurement of reservoir pressure include: (I) gauge errors, and (a) interpretation errors. Gauge errors may be reduced by: (a) reading charts with a comparator microscope, (b) use of hard metal stylus points to give clear lines, (6) insuring temperature equilibrium, and (d) making multiple tests. Check calibrations are equally as important as check well tests. A statistical analysis of such check runs shows quantitatively the advantages of a standardized "zero pressure line'' and of the use of field calibrations made at bottom-hole temperature on the same chart run in the well. Interpretation errors include: (a) fluid heads, which should be corrected to the top of the perforations on the basis of well-fluid gravity and from the top of the perforation to the datum level on the basis of reservoir-fluid gravity, and (b) gradients around the well. Conventional shut-in periods may be entirely inadequate to overcome these, necessitating a reservoir study based on build-up curve data, reservoir history, core analysis and any other available information. Interest in engineering studies of the pressure changes in oil and gas reservoirs is increasing. This type of work yields important information and doubtless will be greatly extended in the future. One of the factors limiting the work, however, is the accuracy with which the reservoir pressures can be determined; for if the inaccuracies in the pressure measurements represent an appreciable percentage of the pressure changes, the engineer is seriously handicapped, and must delay the reservoir study until the reservoir pressure has changed a relatively large amount. This delay can greatly reduce the benefits of such studies, at least from the point of view of aiding the leasing, drilling and completion programs. Thus, from the point of view of reservoir analysis, it is frequently important to obtain the most accurate pressure data possible early in the history of any field—particularly for the gas-distillate fields now being developed. This paper deals with improvements in the measurement of bottom-hole pressures that permit pressures even as high as 4000 or 5000 lb. per sq. in. to be determined with gauge errors of only+ ±I to 2 lb. per sq. in. Since pressures out in the reservoir rather than in the bottom of the hole concern the reservoir analyst, differences between bottom-hole pressures and actual reservoir pressures are also considered. In general, errors in pressure measurement may be divided into: 1. Gauge errors: a. Errors due to inaccuracies in reading the pressure charts. b. Errors due to irreproducibility of the pressure element and recording system. c. Errors caused by failure to allow the gauge to reach temperature equilibrium. 2. Internretation errors: a. Errors caused by a fluid head between the gauge position in tubing and the pressure at the datum level in the reservoir. b. Pressure gradients in the reservoir.

Jan 1, 1946

By T. P. Meloy

The behavior of slime-sized particles in a flotation cell is neither well documented nor well understood. In general, slimes (or 'fines' as they will be alternatively called in this chapter) have been either ignored, eliminated, or treated empirically. Recently, however, some good experimental and theoretical work has been done that leads qualitatively to a clearer understanding of the problems involved. Fines are small particles that, owing to their smallness, behave differently from larger particles of the same material. The smaller the particle, the larger is its surface-to-mass ratio. The difference in the surface-to-mass ratio for a micron-sized particle and a centimeter-sized particle is 10,000 to 1. For our purposes we shall arbitrarily define any particle less than 10 µ 10-3 cm) as being a fine. This is generally considered the upper limit of colloidal-sized particles. Recently, the field of colloidal chemistry has successfully used the concept of the double layer to explain dispersion and flocculation of fine particles in a static system. Flotation, however, is a dynamic system due both to the turbulence of the liquid and to the coursing of the bubbles through the cell. Further more, a flotation system is a heterogeneous system in which there are a number of different types of particles which interact with one another. A further difficulty is that no two flotation systems are the same for minute quantities of a variety of common chemicals will alter the behavior of the system. These reasons make reproducible experimental results that can ex- plain fine-particle behavior difficult to obtain. In spite of these experimental difficulties, millions of tons of ore containing a large amount of fines are successfully floated every year. For example, at the Morning mill of American Smelting and Refining Co., a galena concentrate that was 42% -6 µ and a sphalerite concentrate that was 33% -9 µ were floated leaving a tailing that was 27% - 9 µ.l Ores that contain fines can generally be divided into two classes. In the first are those in which the valuable mineral tends to slime, such as galena and hematite. In the other class, one or more of the gangue minerals forms the slime; a typical example is barite. Though the problems due to the presence of fines are often the same in handling the two classes of ore, the method of handling them is different because of economic considerations. Nonmetallic mineral flotation is particularly affected by slimes, by either slime-coating effects or excessive reagent consumption. Though a given gangue mineral may not float under the conditions prevailing in the flotation cell, it may still be able to adsorb the collector. I£ it also slimes, a significant

Jan 1, 1962

By H. G. Doll

An earlier paper on the general subject of the SP log has analyzed the limitations of that log, in particular when dealing with thin permeable beds enclosed in thick highly resistive ones. Under such conditions, the SP log does not give a good definition of the permeable beds. Selective SP logging is a new method which gives an accurate determination of the permeable beds; even in highly resistive formations, except when the salinity of the mud is extremely high. It also permits a close approxi. mation of the static SP to be obtained. The method consists generally in controlling the potential of auxiliary electrodes located in the drill holes in the vicinity of the measuring electrode. In this manner. the flow of SP current along the drill hole is modified to counterbalance the effect of highly resistive strata. Several procedure; and arrangements used to record selective SP curves and static SP curves are explained. Field examples illustrating these methods are given and discussed. INTRODUCTION In an earlier paper,' the shape of the SP curves and the amplitude of the SP peaks were analyzed, considering how the circulation of the SP current is influenced by the subsurface media as a function of their geometrical configuration and their resistivities. It was shown, in particular. that the permeable beds situated between highly resistive formations are sometimes indistinctly indicated by the deflections of the SP log. It is the purpose of this paper to dircuss a new method now being developed, namely selective SP logging, whose principal feature is to enable a more accurate determination of the depths of the permeable beds present in highly resistive formations, such as occur in limestone fields. It will be shown also how an addi-tional curve called the static SP log can be derived from the selective SP log, or recorded directly, to facilitate the interpretation. Another purpose of the static SP log is to provide an approach toward the determination of the value of the static SP, where this value is not readily given by the SP log. This application. although less important at the present time than that mentioned above, nevertheless is of interest, inasmuch as, according to laboratory and field experiments conducted by several investigators, the determination of oil saturation of reservoirs from the data of the electric log implies the knowledge of the resistivity of the connate water,2,3 to which the static SP seems to be related.4,5,6,7 PRINCIPLE OF SELECTIVE SP LOGGING The method of selective SP logging of the formations traversed by a bore hole consists in recording two curves under the following conditions: The measuring device comprises one measuring electrode M and two additional electrodes G-G', connected to each other. located above and below

Jan 1, 1950

By Henry Eyring, Jay W. Fredrickson

MANY theories have been advanced to explain the phenomena of elastic and plastic deformation. The object of this report is to present a mechanism for deformation, not radically differing from existing theories, but embodying certain principles and concepts of these theories. This proposed theory cannot be the complete answer to the age-old problem of deformation but it is believed that it will be a step further in the proper direction. The plastic properties of solids have recently been reviewed by Seitz and Read.1 Zener2 has reviewed and correlated the existing work on the anelasticity of metals. With these and othersa3,4,5 present theories of deformation are well-known. Of the many theories now extant, those receiving most attention have been proffered by Griffith,6 Becker,7 Smekal,8 Polanyi,9 Orowan10 and Taylor.11Although differing quite widely in details, these theories are based more or less on a common principle of flaws or dislocations that exist in the crystal lattice. The effect of stress concentrations surrounding a flaw or crack has been treated most recently by Fisher and Hollomon.12 The various authors differ as to the exact nature of the flaws or dislocations, the causes of their appearance, or the manner in which they initiate slip. All of the theories agree that the number of dislocations increases with progressing deformation. It is universally agreed that the shearing process is not a simple gliding of ideally perfect atomic lattice planes. It is also agreed that the "macroscopic process of gliding, or slip, is brought about by the spreading of a large number of locally initiated "glide steps" through the whole crystal. The occurrence of these "glide steps" is closely related to the presence of some kind of deviations from the "ideal" lattice structure, even in the undeformed crystal. These deviations are overcome "one at a time," in a manner of speaking, due to some stress-concentrating effect." PROPOSED THEORY Many solids show a continuously increasing deformation if subjected to a constant load of suitable magnitude in an extended range of temperature for a sufficient time. This deformation, or flow, may be said to be due, in general, to the tendency of the atoms or molecules in an elastically stressed body to readjust themselves in such a way that if the deformation were kept constant, a release of stress would take place. If rupture does not occur, this process of relaxation causes the rate of flow to obtain a final constant value, as shown in the curve (Fig I) obtained by Taylor and Quinney.14 In. this state the release of stress by relaxation exactly counterbalances the increase due to the elastic strain on the test pieces. .

Jan 1, 1948

By H. Q. Golder

With the development of open-pit mines of ever increasing depth, the stability of the pit slopes in soil and rock is of growing economic importance. How is it, considering the newness of the problem that we know anything at all about the stability of man-made slopes? How much do we know and how did it all begin? We can make a reasonable estimate of the stability of a slope in soil, but we know as yet woefully little about slopes in rock because the problem is much more complex. It is only with the development of the capacity of the computer to handle wearisome calculations that any but the simplest of stability problems in rock have become possible of solution. But what we do know is a guide of immense value in the design of slopes in rock. But remember that the computer is a great elevator; it takes everyone's feet off the ground! So our study began with soils and what is now known as "Soil Mechanics", which is a translation of the German term "Bodenmechanik". It is a pity that the title of Terzaghi's book "Erdbaumechanik" was not used instead. But here the task of the translator is difficult because English lacks the facility of German to string together several words and make a new one whose meaning is unequivocal. Thus, we have the three German words 'Erde' 'Bau' and 'Mechanik'. 'Erde' means "earth" in almost all the English senses including "soil". 'Bau' and 'bauen' convey the meaning of building and construction, and 'Mechanik' means "mechanics" which includes statics and dynamics and the 'mechanics of materials', etc. So that a correct translation of the German is a phrase like "the mechanics of construction with, in or on, earth or soil." However we are stuck with 'Soil Mechanics' and that is where it all began. Now this study or subject did not begin with 'Terzaghi' although his contribution to the subject is unquestionably greater than that of any other single person. Every scientific discipline has its 'classical problem' and that of soil mechanics is 'the earth pressure problem' and it began in the 17th century. In fact, it probably began before this with the introduction of gunpowder to Western Europe in about the 15th century, but the first known reference to the problem was by Vauban, a distinguished French military engineer who lived from 1633 to 1707 and who gave rules for the dimensions of retaining walls from 6 to 80 ft. in height. The soil properties were not mentioned by Vauban probably because the rules were intended to be applied to fortifications only, but Poncelet (1840) claimed that Vauban's rules were based on a theory, and not simply on military and practical

Jan 1, 1972

By Thomas Fraser, H. F. Yancey

Prior to the war just ended, Germany was the greatest coal producer in continental Europe. In 1943 the production of coal, bituminous and higher in rank, together with brown coal calculated to the equivalent amount of bituminous coal, is estimated to have been about 240 million metric tons, according to the War Department. Before the war production in Germany exceeded consumption. No other country in continental Europe except Poland had a large surplus. However, England's surplus was the largest in Europe as a whole. Before World War II the Ruhr Basin normally supplied about 70 pet of the total production of high-rank coal, the Saar and Aachen about 6 pet each, Upper Silesia about 14 pet, and Silesia and Saxony the remainder. Nearly one third of the brown coal was produced in the Rhineland, a little less than one half in central Germany nest of the Elbe River, and about one fourth east of the Elbe. Bituminous coal and brown coal together constituted by far the most important energy resources of the old German Reich. Bituminous coal furnished nearly 70 pet of the total energy requirement, brown coal supplied about 25 pet, and water power, wood, petroleum and alcohol together aggregated only 7 pet. Because it was the most important single mineral resource of Germany, an excess of coal enabled the Reich to import nearly all the other mineral products that she lacked, such as iron ore from Lorraine. The area adjacent to the coal fields was supplied with gas from an interconnected grid. Similar electric grids are based on brown coal with the power stations at the mines. Coal tar provided the foundation for the development of the extensive German chemical industries as exemplified by the I. G. Farbenindustrie. For almost a century, German scientists have been adequately supported both by the State and by industry in studying improved methods of utilizing coal. In Germany the mineral rights were reserved by the State and ordered eatraction of coal was enforced. Each lease comprised a relatively extensive area. which accounts for the generally large size of the mines and mining companies In 1938 there were 160 mines in the Ruhr, with a total output of 125 million tons but 90 pet of the production was controlled by 20 companies. By far the largest single coal-mining company in Germany was the Gelsen-kirchener Bergwerke A. G., which produced nearly 27 million tons in the Ruhr in 1937. Second was Saargruben A. G. a State-owned company operating in the Saar, which produced 'lore than '3 million tons. Third was Bergwerksgesellschaft Hibernia A. G., with 10 million tons, also in the Ruhr. Briquettes are made from both bitumillous coal and brown coal, but in 1938 some 44 million toils of brown-coal bri-

Jan 1, 1947

By Thomas Fraser, H. F. Yancey

Prior to the war just ended, Germany was the greatest coal producer in continental Europe. In 1943 the production of coal, bituminous and higher in rank, together with brown coal calculated to the equivalent amount of bituminous coal, is estimated to have been about 240 million metric tons, according to the War Department. Before the war production in Germany exceeded consumption. No other country in continental Europe except Poland had a large surplus. However, England's surplus was the largest in Europe as a whole. Before World War II the Ruhr Basin normally supplied about 70 pet of the total production of high-rank coal, the Saar and Aachen about 6 pet each, Upper Silesia about 14 pet, and Silesia and Saxony the remainder. Nearly one third of the brown coal was produced in the Rhineland, a little less than one half in central Germany nest of the Elbe River, and about one fourth east of the Elbe. Bituminous coal and brown coal together constituted by far the most important energy resources of the old German Reich. Bituminous coal furnished nearly 70 pet of the total energy requirement, brown coal supplied about 25 pet, and water power, wood, petroleum and alcohol together aggregated only 7 pet. Because it was the most important single mineral resource of Germany, an excess of coal enabled the Reich to import nearly all the other mineral products that she lacked, such as iron ore from Lorraine. The area adjacent to the coal fields was supplied with gas from an interconnected grid. Similar electric grids are based on brown coal with the power stations at the mines. Coal tar provided the foundation for the development of the extensive German chemical industries as exemplified by the I. G. Farbenindustrie. For almost a century, German scientists have been adequately supported both by the State and by industry in studying improved methods of utilizing coal. In Germany the mineral rights were reserved by the State and ordered eatraction of coal was enforced. Each lease comprised a relatively extensive area. which accounts for the generally large size of the mines and mining companies In 1938 there were 160 mines in the Ruhr, with a total output of 125 million tons but 90 pet of the production was controlled by 20 companies. By far the largest single coal-mining company in Germany was the Gelsen-kirchener Bergwerke A. G., which produced nearly 27 million tons in the Ruhr in 1937. Second was Saargruben A. G. a State-owned company operating in the Saar, which produced 'lore than '3 million tons. Third was Bergwerksgesellschaft Hibernia A. G., with 10 million tons, also in the Ruhr. Briquettes are made from both bitumillous coal and brown coal, but in 1938 some 44 million toils of brown-coal bri-

Jan 1, 1947

By V. H. Wilhelm

The year 1941 in the California oil industry was marked by an increased market demand, drilling activity, and production of crude oil. Although seven new oil fields and two gas fields were discovered during the year, additions to reserves from these discoveries, as well as extensions and revaluations of previous discoveries, were approximately 100 million barrels, as against estimated withdrawals of 230,233,000 barrels. The year was remarkable for the very great increase in domestic demand for all products, which more than compensated for the loss in shipments to Japan, which averaged 60,041 bbl. Per day during 1940. Demand in terms of crude during 1941 was 648,967 bbl. per day as against 632,647 for the same period in 1940. This abnormal increase in demand is due to increased industrial activity, and especially increased railroad activity. Gasoline consumption for 1941 was 241,011 bbl. per day as against 217,744 in 1940. Demand for fuel oil increased from 259,806 bbl. per day in 1940 to 285,896 in 1941, and caused a withdrawal from stocks of more than 7,473,000 barrels. During 1941, total oil storage declined 9,153,000 bbl., but additions to storage of 1,754,000 bbl. of light oil and light oil products were offset by a withdrawal of 10,907,000 bbl. of heavier products. Production during the year is estimated at 230,233,000 bbl. as against 222,784,386 bbl. for 1940. TraNsportation For a short time, California was affected by lack of transportation due to the diversion of tankers. This shortage affected the movement of oil from the Sari Joaquin mated to the refineries, since a large percentage of this production is moved to the coast through pipe lines, and thence by tankers to Los Angeles and San Fran-,iSco, Return of the tanker fleet, which may be temporary, indicates that there is a possibility of ample supplies of petroleum products in the Pacific Northwest. Drilling Activity Contrary to general opinion, drilling activity increased in 1941 over the pre-vious Year, 942 wells being completed in 1941 as against 890 in 1940, an increase Of 6 per cent. This increase was due to the increased demands for fuel oil, and also to the decreased drilling costs, which made many former marginal locations economic. The main activity caused by increased demands for fuel oil was in the Mt. Poso, McKittrick, Midway and Santa Maria Valley oil fields. Dry-hole footage in 1941 was 655,354 ft. as against 583,537 ft. for 1940. Curtailment Voluntary curtailment succeeded in holding production considerably below demand, although it was above the state quota. During the year the top allotment

Jan 1, 1942

By V. H. Wilhelm

The year 1941 in the California oil industry was marked by an increased market demand, drilling activity, and production of crude oil. Although seven new oil fields and two gas fields were discovered during the year, additions to reserves from these discoveries, as well as extensions and revaluations of previous discoveries, were approximately 100 million barrels, as against estimated withdrawals of 230,233,000 barrels. The year was remarkable for the very great increase in domestic demand for all products, which more than compensated for the loss in shipments to Japan, which averaged 60,041 bbl. Per day during 1940. Demand in terms of crude during 1941 was 648,967 bbl. per day as against 632,647 for the same period in 1940. This abnormal increase in demand is due to increased industrial activity, and especially increased railroad activity. Gasoline consumption for 1941 was 241,011 bbl. per day as against 217,744 in 1940. Demand for fuel oil increased from 259,806 bbl. per day in 1940 to 285,896 in 1941, and caused a withdrawal from stocks of more than 7,473,000 barrels. During 1941, total oil storage declined 9,153,000 bbl., but additions to storage of 1,754,000 bbl. of light oil and light oil products were offset by a withdrawal of 10,907,000 bbl. of heavier products. Production during the year is estimated at 230,233,000 bbl. as against 222,784,386 bbl. for 1940. TraNsportation For a short time, California was affected by lack of transportation due to the diversion of tankers. This shortage affected the movement of oil from the Sari Joaquin mated to the refineries, since a large percentage of this production is moved to the coast through pipe lines, and thence by tankers to Los Angeles and San Fran-,iSco, Return of the tanker fleet, which may be temporary, indicates that there is a possibility of ample supplies of petroleum products in the Pacific Northwest. Drilling Activity Contrary to general opinion, drilling activity increased in 1941 over the pre-vious Year, 942 wells being completed in 1941 as against 890 in 1940, an increase Of 6 per cent. This increase was due to the increased demands for fuel oil, and also to the decreased drilling costs, which made many former marginal locations economic. The main activity caused by increased demands for fuel oil was in the Mt. Poso, McKittrick, Midway and Santa Maria Valley oil fields. Dry-hole footage in 1941 was 655,354 ft. as against 583,537 ft. for 1940. Curtailment Voluntary curtailment succeeded in holding production considerably below demand, although it was above the state quota. During the year the top allotment

Jan 1, 1942

By Walter E. Duncan

The ores treated at the concentrating plant of the Mahoning Mining Co. at Rosiclare, Ill., come largely from the blanket replacement deposits of the northeastern part of Hardin County, Illinois, and consist of complex mixtures of galena, sphalerite and fluorspar in a gangue of quartz, limestone and sandstone. The several minerals are so intimately inter-grown that they are not liberated at the sizes usually treated by gravity concentration in the usual fluorspar plant. For this reason, an all-flotation method of concentration was developed in cooperation with the station of the U. S. Bureau of Mines at Rolla, Mo.1 This flotation separation made possible the commercial production of four coyentrates: (I) lead, (2) zinc, (3) acid-grade fluorspar and (4) metallurgical-grade Auorspar.2-3 Although fluorspar had been floated in Canada in 19214 and a plant at Rosiclare had been floating fluorspar since March 1929, fluorspar flotation was given considerable impetus by the Mahoning developments, since some features of the separation were quickly adopted by other fluorspar companies. The Bureau of Alines5 reports that in the 10 years preceding 1938 only 50,552 tons of fluorspar flotation concentrates were produced in the United States. The rise from this almost nominal figure to 153,750 tons (largely acid grade) in one year (1944)6 is indicative of the activity in fluorspar flotation occasioned by the war. The industry thus proved to be in a position to expand and keep up reasonably well with the requirements imposed upon it by such developments as occurred in high octane aviation gasoline alkylation, in the use of Freon as a refrigerant and as carrier in the Aerosol "bug bomb," and in the atomic bomb project as well as in the expansion of other activities requiring hydrofluoric acid; for example, the aluminum industry. Despite the fact that the greater portion of acid-grade fluorspar produced in the last few years went directly into war uses, the future of the acid-grade field still appears bright. As a result of the activity in fluorine chemistry during the war, it seems likely that in the relatively near future almost every phase of human endeavor will find some fluorine compound involved. The other three concentrates produced deserve some attention in these introductory remarks. The lead concentrates first produced contained both zinc and fluorspar but these did not interfere with their marketing. As will be pointed out later, the quality has steadily improved until today it is a relatively high-grade product. Although some zinc smelters accept concentrates containing limited quantities of fluorspar, it is a very objectionable impurity. Since flotation methods fail in the complete removal of the fluorspar, chemical methods were developed for

Jan 1, 1948

By R. T. DeHoff

A new approach to the measurement of the size distribution of particulate structures imbedded in opaque bodies is developed. The method is based upon the assumption of a general two-parameter distribution curve, and the estimation of these two parameters from three well-known counting measurements made upon metallogvaphic sections. The total number of particles in the system is also a product of the analysis. Application of the method with the assumption of the logarithmiconorma1 disfribution function is developed in detail. A complete description of the geometry of a particulate structure requires the determination of the size distribution of particles. The problem of estimating the size distribution of particles of a particular phase in a multiphase system, or the grain-size distribution in a homogeneous system, has been approached by many investigators.'-'0 All of the solutions proposed by these investigators share the following characteristics. a) A minimum of several hundred particle sections in the microstructure must be examined, and some characteristic dimension recorded, such as area,3'5 intercept length,6"9 or diameter.1'2'4'10 b) The resulting data must undergo a series of fairly complex calculations to generate the empirical histogram which describes the size distribution in three dimensions. c) In order to manipulate the result, the histogram must be fitted to some assumed mathematical formula, using the attendant statistical procedures. d) With two notable exceptions,8,10 the particles must be spherical. The measurements and calculations involved are in general very tedious and time-consuming, with the logical result that much effort has been expended in the development of equipment which will perform these tasks automatically and semiautomati-cally.9,11-15 considerable success has been achieved in this area, but the equipment is in general expensive, and usually places stringent requirements On the quality of microstructure which can be reliably analyzed. In laboratories which do not possess such equip- ment, the analysis of geometry is usually limited to measuring total properties of the microstructures, such as volume fraction and interfacial area, because the measurements required are much simpler to make. The determination of size distributions rarely is undertaken. The development which is presented in this paper permits the estimation of size distributions of three-dimensional structures from the same simple counting measurements which are required to determine the surface area and volume fraction of the particulate structure, and one other counting measurement. The basic approach that is used is to assume a general mathematical form for the distribution, which is described by two parameters (as the normal distribution is described by assigning values to the mean and the standard deviation), and then estimate these two parameters from the results of the counting measurements. The introduction of a third counting measurement also permits the evaluation of the number of particles per unit volume, Nv.

Jan 1, 1965

By Walter E. Duncan

The ores treated at the concentrating plant of the Mahoning Mining Co. at Rosiclare, Ill., come largely from the blanket replacement deposits of the northeastern part of Hardin County, Illinois, and consist of complex mixtures of galena, sphalerite and fluorspar in a gangue of quartz, limestone and sandstone. The several minerals are so intimately inter-grown that they are not liberated at the sizes usually treated by gravity concentration in the usual fluorspar plant. For this reason, an all-flotation method of concentration was developed in cooperation with the station of the U. S. Bureau of Mines at Rolla, Mo.1 This flotation separation made possible the commercial production of four coyentrates: (I) lead, (2) zinc, (3) acid-grade fluorspar and (4) metallurgical-grade Auorspar.2-3 Although fluorspar had been floated in Canada in 19214 and a plant at Rosiclare had been floating fluorspar since March 1929, fluorspar flotation was given considerable impetus by the Mahoning developments, since some features of the separation were quickly adopted by other fluorspar companies. The Bureau of Alines5 reports that in the 10 years preceding 1938 only 50,552 tons of fluorspar flotation concentrates were produced in the United States. The rise from this almost nominal figure to 153,750 tons (largely acid grade) in one year (1944)6 is indicative of the activity in fluorspar flotation occasioned by the war. The industry thus proved to be in a position to expand and keep up reasonably well with the requirements imposed upon it by such developments as occurred in high octane aviation gasoline alkylation, in the use of Freon as a refrigerant and as carrier in the Aerosol "bug bomb," and in the atomic bomb project as well as in the expansion of other activities requiring hydrofluoric acid; for example, the aluminum industry. Despite the fact that the greater portion of acid-grade fluorspar produced in the last few years went directly into war uses, the future of the acid-grade field still appears bright. As a result of the activity in fluorine chemistry during the war, it seems likely that in the relatively near future almost every phase of human endeavor will find some fluorine compound involved. The other three concentrates produced deserve some attention in these introductory remarks. The lead concentrates first produced contained both zinc and fluorspar but these did not interfere with their marketing. As will be pointed out later, the quality has steadily improved until today it is a relatively high-grade product. Although some zinc smelters accept concentrates containing limited quantities of fluorspar, it is a very objectionable impurity. Since flotation methods fail in the complete removal of the fluorspar, chemical methods were developed for

Jan 1, 1948

By R. J. Teitel

FOUR or five years ago an investigation was initiated to study and develop basic information on llquid metal fuels for future power nuclear reactors. The objective was to find fluid forms of uranium (solutions or dispersions) in low melting alloys. A summary of the different fuels was presented in a recent article by Teitel, Gurinsky, and Bryner.' The combination of uranium and bismuth, with its low thermal neutron cross section and low melting point, is of basic interest to the development of these fuels. Most of the previous effort on the U-Bi phase diagram was done under security regulation. Ahmann and Baldwin' reported their findings on the U-Bi system in 1945. Their results indicated that the phase diagram had at least two compounds and possibly one more. UBi, and UBi were established by chemical analyses of residues after high temperature centrifugation of alloys. UBi, decomposed peritectically at1980°C and there were signs of another reaction above that. UBi melted at a very high temperature, and there were also signs of a monotectic at high temperatures in high uranium alloys. The solubility of uranium in liquid bismuth has received attention by three groups of authors: Bareis,X ayes and Gordon,' and Ahmann and Baldwin.' The latest and most widely accepted data is that of Bareis, and it is included in Fig. 1 along with new data at higher temperatures. Brewer et al." and Ferro"'' have used X-ray diffraction to determine the number and crystal structure of the compounds. Brewer identified the structure of UBi to be a simple NaCl cubic structure having a cell edge of 6.364A. The density of the compound was calculated to be 11.52 g per cu cm. Two other unindexed patterns were presented as possibly belonging to two other compounds. Ferro agreed with Brewer on the crystal structure of UBi and identified the structure of UBi, and U,Bi,. The intermetallic compound UBi, has a tetragonal cell with a = 4.445A and c = 8.908A. The density of the compound was determined and the number of atoms per cell (six atoms) was calculated. The X-ray density reported was 12.35 g per cu cm. The compound UsBir was treated in a similar way and it was reported to have a cubic structure 9.35A on an edge and to contain 28 atoms per cell. The density was given as 12.59 g per cu cm. Teitel reported that there was a compound UaBi, and no UBi, compound. (The difference in the compositions is 3.3 pct U.) This conclusion was based upon the extrapolation of some 20 tie lines in the

Jan 1, 1958

Duval Corporation, the owners of the Sierrita, Esperanza, and Mineral Park copper operations in Arizona, first acquired the mineral rights to their Battle Mountain, Lander County, Nevada, property in 1962. Development of the mine commenced in mid - 1965, and the copper operation began at the end of 1968. The ore, a mixture of chalcocite and chalcopyrite, was milled and floated at a rate of 3, 175 mtpd (3,500 stpd). Because of low copper grade and price, the plant was shut down after about ten years of operation. Attention was then turned to an adjacent low-grade precious metal ore body which contained 2.74 g Au and 3.4 g Ag per mt (0.08 oz Au and 0.10 oz Ag) and minor amounts of copper. Test work revealed recovery by Carbon-In- Pulp treatment would amount to approximately 2.8 mt (90,000 oz) each of gold and silver per year. A rapid engineering and construction schedule resulted in the world's largest, as of late 1980, Carbon-In- Pulp plant being put on-stream in January 1979, with a capacity of 2.720 mtpd (3,000 stpd). Fortunately, the original crushing and grinding plant with all its infra structure was available, and the only modification needed was the addition of a gravity circuit to remove coarse free gold ahead of Carbon- In-Pulp treatment. One of the four primary 500 mm (20 in.) cyclone underflows in the primary ball mill circuit is directed to a secondary ball mill where its product is again cycloned. The cyclone underflow is screened at 3,360 microns (6 mesh) with the undersize being treated on two Pan American 1.07 m by 2. 14 m (42 in. by 84 in.) jigs. Hutch product is further concentrated on two Wilfley tables, a magnetic separator, and on a third Wilfley table where approximately 930 g (30 oz) of gold are recovered each day for amalgamation, retorting, and smelting. Returning to the grinding circuit, the final cyclone overflow is sent to the original plant tailings thickener to obtain proper pulp density for Carbon-In-Pulp treatment. Thickener underflow, at about 40% solids, is then conditioned with air and lime in a series of two 8.5 m by 9.75 m (28 ft by 32 ft) 15O cone bottom Pachucas for oxidation of pyrrhotite. The pulp is then split into two streams for cyanidation for 48 hours in two lines of eight Pachucas of the same size. Pulp is transferred from tank to tank by auxiliary air lifts. Cyanided pulp is then sent to a series of six C. I. P. mechanically agitated tanks with one hour retention in each tank. Originally these

Jan 1, 1981

THE Institute assembled in the Court-House, on Tuesday evening, May 22d, and was called to order by Vice-President E. B. Coxe. After announcement by the Local Committee of the programme for excursions, the Secretary read the following annual report of the Council The Council, in presenting to the Institute its annual report, has to record a most eventful year in the history of the Institute. Three meetings, as usual, have been held, two in Philadelphia and one in New York. At the Philadelphia meetings in June and October, there were present many distinguished foreign engineers, some of whom contributed communications to the Institute, and took part in its discussions. Sixty-seven papers have, in all, been presented to the Institute, which will be published in the fifth volume of Transactions. There has been an accession to the membership of 1 honorary member, 11 foreign members, and 162 members and associates; -8 have resigned, 6 have died, and 30 have been dropped from the roll, after due notification, for non-payment of dues. The membership now comprises 5 honorary members, 60 foreign members, and 644 members and associates, in all 699. As worthy of especial mention in the work of the year are the Discussions on Technical Education in connection with the American Society of Civil Engineers, and the report of the-International Committee appointed by the Institute to consider the nomenclature of iron and steel. The Discussions on Technical Education have been published in a separate volume, and comprise a valuable and suggestive collection of the views of practical engineers and educators. The report of the International Committee, composed of Messrs. Akerman, of Sweden; Bell, of England; Tunner, of Austria; Gruner, of France; Wedding, of Prussia; and Holley and Egleston, of the United States, has received the careful attention of engineers and metallurgists of all countries, and has met . with very general acceptance. Of the work of the Centennial Committee in Philadelphia the members are generally familiar, from personal experience, and from the detailed report of the committee at the last meeting of the Institute. But the record of the service rendered by this committee would he incomplete without mention of the numerous letters of thanks and formal expressions of obligations received by the Institute from individuals, societies, and governments abroad. The wise and generous spirit in which the work of the committee was planned, and the laborious and self-sacrificing manner in which it was carried out, call for emphatic expressions of thanks from the Institute. The gifts of Centennial exhibits to the Institute, largely as testimonials for services rendered, has necessitated the appointment of a Museum Committee for

Jan 1, 1878

By J. G. Thompson

Determinations of the hydrogen content of irons and steels invariably are subject to two serious difficulties: (I) the determination of amounts of 0.001 per cent or less of any constituent requires an analytical procedure of unusual precision and accuracy, and (2) the hydrogen content of many samples is dccidedly not stable; i.e., there is no assurance that the content at the time the analysis is made is the same as it was when the sample was taken or at some previous time in the history of the piece. In respect to both the precision and speed of the determination, the vacuum-extraction procedure for the determination of hydrogen possesses advantages over the vacuum-fusion procedure, which has been the recognized standard for the detcrmination of other gaseous elements in sted-— oxygen and nitrogen for example. The basic facts upon which the vacuum-extraction procedure is based—i.e., the evolution of gas from solid steel when it is heated in vacuum, and the fact that the evolved gas is rich in hydrogen—were observed by Graham1 many years ago. Subsequent investigations have shown that hydrogen exists in steel chiefly as interstitial solid solution (i.e., in atomic dispersion) and perhaps to some extent as hydridcs that are unstable and decompose to form atomic hydrogen. In either case practically all of the hydrogen in steel at elevated temperatures exists in the atomic condition and consequently is able to diffuse readily through the metal. In contrast to this, other gaseous elements, such as oxygen and nitrogen, normally are present in steel chiefly in the form of relatively stable compounds such as oxides or silicates and nitrates; i.e., the oxygen and nitrogen atoms are fixed in stable combinations and are not free to migrate. The only oxygen or nitrogen that can diffuse in steel is the small amount in solution (atomically dispersed) and the rate of diffusion of these atoms is much less than that of hydrogen because of their greater atomic volume and lower mobility. Consequently, it is possible to extract most or all of the hydrogen from solid steel in a reasonable time at moderately elevated temperatures, but the procedure is not applicable to the determination of oxygen or nitrogen. It is only within the last decade that these observations have been developed into an analytical procedure for the determination of hydrogen. Apparatus and Procedure The apparatus used at the National Bureau of Standards,6 for the determination of hydrogen by the vacuum-extraction procedure, is shown schematically in Fig. I. The specimen, freshly cleaned and dried,* is suspended on a fine wire within the quartz furnace tube that is connected to the reservoir system and analytical train.

Jan 1, 1945

By Don B. Carson, Donald L. Katz

NATURAL gases under pressure form crystal-line hydrates with water. Experimental data are reported on four-phase equilibrium for the methane-propane-water, methane-pentane-water, and methane-hexane-water systems. Temperatures and pressures for equilibrium between gas, water-rich liquid, hydrocarbonrich liquid, and hydrate were measured, as well as the percentages of methane and propane in the hydrate. The data indicate that natural gas hydrate behaves as a solid solution and that pentanes and heavier hydrocarbons do not enter into the solid phase. Vapor-solid equilibrium constants are presented that permit the approximation of the conditions for hydrate formation, from the composition of a gas. INTRODUCTION Natural gas hydrates have been the object of considerable research in recent years, because of the trouble they have caused in the natural-gas and natural gasoline industries. Natural gas hydrates are white crystalline compounds of water and gas, which, under pressure, exist at temperatures considerably above the freezing point of water. Because of the relatively high temperatures at which the hydrates exist, they become a nuisance in high-pressure gas operations where water is present, since their formation causes partial or complete plugging of valves and pipes. From a practical standpoint, the trouble incident to hydrate formation has been solved by dehydration of the gas before it enters the plant or pipe line, or by other remedial measures. Extensive work on gas hydrates in the latter part of the nineteenth century, by Villard1 and others, gave data on methane hydrate and on ethane hydrate. Schroeder summarized these theoretical studies.2 Hammerschmidt3 introduced the information on gas hydrates to the gas industry and Deaton and Frost4-6 gathered a considerable number of data on the behavior of natural gas hydrates. Recent papers7,8 have extended both the data and the theory of these hydrates. At present, data are available on temperatures and pressures of hydrate formation for pure methane, ethane, propane, n-butane, methane-ethane mixtures, methane-propane mixtures, methane-butane mixtures, and some 15 natural gases, all in the presence of excess water. However, up to the present time no method has been available for predicting the temperature at given pressures or the pressure at given temperatures at which natural gases will form hydrates if saturated with water. This paper pre¬sents data on the methane-propane-water, methane-pentane-water and methane-hexane water systems in four phases, one of which is the hydrate. The application of the phase rule to the methane-propane-water data proves that hydrates behave as solid solutions. The data of this paper and those in the literature were used to develop vapor-solid equilibrium constants,8 which permit prediction of conditions of hydrate formation from the analysis of a natural gas.

Jan 1, 1941

By C. V. Millikan, Herbert F. Beardmore

Declining Productivity Index, as considered herein, is a productivity index that has a substantially and consistently decreasing value when measured over a period of a few hours. If not recognized, it may be interpreted as representing an unsettled or unstable condition in a producing well. It forms the basis of a number of predictions as to future performance compared with the performance of wells in which the productivity index does not decline. The nost important of these are that: (I) the rate of oil production will decline more rapidly, (2) the gas-oil ratio will usually increase abnormally, (3) the amount of water ultimately produced will be negligible, if any, (4) stop-cocking will increase current production and decrease gas-oil ratio. When such relative well performance is indicated, it follows that certain reservoir performance and operating practices may be anticipated: (I) disappointing recovery, (2) longer natural flow, (3) no active water drive, (4) better evaluation of acidizing, shooting and reworking, (5) intermittent operation of wells, (6) smaller pumping equipment required. It is significant that the basis of these important predictions is bottom-hole pressure tests that can be made immediately after completion of the wells. Introduction "'Productivity index" is the number of barrels of oil produced per day per pound per square inch of differential pressure between the reservoir and the bottom of the well. "Declining Productivity Index," as considered herein, is a productivity index that has a substantially and consistently decreasing value when measured over a period of a few hours. Productivity index can be determined only when the rate of production can be stabilized. In most wells the rate of production and bottom-hole pressure are easily stabilized to give a constant productivity index for a period of many hours. A few produce so erratically as to preclude probability of an acceptable test in the usual sense. A satisfactory productivity index can be determined in some wells only by gauging the production accurately by hours, measuring the bottom-hole pressure continuously, and from these data calculating the productivity index for successive hours. Such figures frequently will have a decreasing value—that is, a declining productivity index—and when plotted on double. logarithmic cross-section paper with productivity index as ordinate and time as abscissa will be a straight-line curve. The angle between the curve and the abscissa is referred to as the rate of decline. Declining productivity index may appear to be the result of change in permeability to oil due to decreasing saturation of oil and increasing saturation of gas in the reservoir. It is possible that such is in fact the cause, but if so, more is involved than merely relative saturation of oil and gas. This seems evident because the rate of decline in productivity index is substantially the same regardless of the pro-

Jan 1, 1945

By Harold Vagtborg

Equilibrium vaporization ratios were obtained for light hydrocarbons, nitrogen, carbon dioxide, and hydrogen sulfide in a reservoir fluid containing 35 mole per cent hydrogen sulfide. The data cover the range from 700 to 2500 psia at 154°F. The results of this study are compared with results obtained by other investigators on systems containing less hydrogen sulfide. When large amounts of hydrogen sulfide are present, the equilibrium vaporization ratios for ethane and heavier hydrocarbons are greater than the ratios for systems containing little or no hydrogen sulfide. Large amounts of hydrogen sulfide have the reverse effect on the ratios for methane. Routine PVT studies were performed on the reservoir fluid including flash and differential liberations of the dissolved gas. The pressure-volume relationships of the saturated fluid were also determined. It is shown that the use of published correlations on physical properties of reservoir .fluids can lead to gross errors when applied to systems containing large amounts of hydrogen sulfide. INTRODUCTION Equilibrium vaporization ratios for various components in naturally occurring crude oil and condensate systems have been reported in the literature.1,2,3,4 Recently, several papers have been published with emphasis on non-hydrocarbon components such as nitro- gen, carbon dioxide and hydrogen sulfide.5,6,7,8,9 The increased discovery of reservoir fluids having high concentrations of these non-hydrocarbon components, particularly hydrogen sulfide, has created a need for a further study of their phase behavior. Equilibrium vaporization ratios are known to vary with pressure, temperature, and overall composition of the system.'" It was anticipated that ratios for systems containing large amounts of hydrogen sulfide would differ from the ratios for systems containing small amounts of hydrogen sulfide. Therefore, the present work was undertaken in order to obtain reliable equilibrium vaporization ratios for the reservoir-fluid in question. PROCEDURE The procedure followed was evolved after considerable experimentation on methods of handling the very sour crude. It was found that drying agents (e.g. CaCl2 and CaSO4) absorbed an appreciable amount of hydrogen sulfide from the gas used to prepare the recombined samples. The concentration of hydrogen sulfide dropped as much as 10 mole per cent in a single pass through a 3-ft drying tube. It was also found that when undried gas was agitated with mercury in the PVT cell, a black scum, believed to be mercuric sulfide, was formed and the hydrogen sulfide content of the gas dropped several mole per cent. Because composition changes during a run could not be tolerated, separation of the mercury and sour fluid was necessary. In order to effect this separation, a stainless steel piston, equipped with Teflon O-rings, was placed in the PVT cell between the mercury and the sour fluid. This piston had to be constructed in three parts because

Jan 1, 1955

By F. H. Turan, F. W. Jessen

The gel strength and viscosity of two different suspensions of fractionated montmorillonite clay were measured by using a Stormer viscosimeter and Farm V-G meter. The amount of sodium poly-phosphate (sodium bexametaphosphate, sodium tetraphosphate and sodium acid pyrophosphate) adsorbed by the clay particles was determined. A relationship seems to exist between the amount of polyphosphate adsorbed and the nature of the surface, edge or plate, assumed to be the principal sites for selective adsorption. Reduction in viscosity and gel strength was found to be directly related to the adsorption. Both chemical bonding and physical adsorption seem involved in defloccula-tion Some indication of the axial ratios of particles of .l- to .04-micron average size is possible though study of the adsorption mechanism. INTRODUCTION AND PURPOSE A knowledge of surface areas of clay particles in a suspension and a precise determination of phosphate adsorption should provide a basis for a better understanding of reduction in viscosity and gel strength caused by molecularly dehydrated phosphates. The purpose of this investigation was to study the adsorption of sodium polyphosphates on suspensions of fractionated sodium montmorillonite. Although there is considerable uncertainty regarding details of the structure of montmorillonite, a generally accepted one is that suggested by Hofmann, Endell and wi1m.l The structure shown in Fig. 1 is an idealized one, and Marshall2 has postulated that it is possible for several isomorphous replacements to occur. Thus, aluminum may replace silicon, in which case an exchangeable cation would go along with the aluminum to neutralize what would otherwise be a net negative charge on the structure. There is disagreement among various investigators as to the particle size and shape of montmorillonite clays. Marshall2 reported the following results for the mean lateral dimensions of a Putnam clay (montmorillonite)— 3,730 A° for particles having average diameters ranging from 500 to 1,000 A, and 750 A° for those with an average diameter less than 200 A. The latter particles were estimated at 50A°in thickness, which would correspond to a stack of five unit cell layers. On the other hand, Shaw3 has interpreted micrographs as indicating that particles of montmorillonite ire readilv broken down to the individual cell layers by dispersion in water. Brindley4 and Merings indicate the ultimate particles to be of the order of 300 A° in mean lateral dimension. Van Olphen6 suggested the thickness of particles at four to five unit cell layers. It was suggested also that this number tends to become smaller with increasing dilution. Recently, Kahn and Lewis7 determined the size of sodium montmorillonite particles in aqueous suspension from electro-optical bi-refringence decay curves. The