Search Documents

By W. W. Weigel

The mines of the St. Joseph Lead Co. in St. Francois County, Missouri, form a roughly triangular area of about 45 square miles. Locally this is known as the Lead Belt. The four operating mines in the area at present are the Federal, Leadwood, Desloge, and Bonne Terre, in decreasing order of mine area and daily production. Mining began in 1864 and has been carried on in the district continuously since that time. As a group, the Lead Belt mines now handle 20,000 gal. per min. of water, average head about 465 ft., against a normal daily ore tonnage of 21,200 tons. For a six-day operating week this gives a ratio of 6½ tons of water per ton of ore. Total average pumping in 1931 was about 15,000 gal. per min. Since that time a large area of virgin territory has been opened, much of which has had temporary flush flows. About 75 per cent of the water enters in certain restricted very wet areas. Production figures are given in Table I. The figures by divisions for 1931 and 1941 are not exactly comparable, as there were several transfers of pumping loads from one division to another during that period of time. Geology The, basement formation in 'the Lead Belt area consists of the pre-Cambrian rhyolite porphyry and granite. Overlying this is the La Motte sandstone, of Middle Cambrian age, which offers a good medium for circulation of water. It varies in thickness up to 400 ft. Above this is the Bonne Terre dolomite, approximately 375 fl. thick, which in turn is overlain by the 150-ft. Davis shale. The formations above this, present in the Lead Belt in small areas only, are of minor importance. The ore bodies occur as large, horizontal tabular masses or as long, narrow runs; they are found throughout the Bonne Terre but largely in the lower 150 ft. The rather indefinite contact with the La Motte is a favorite ore horizon. Milling is entirely by open stope and pillar breast systems. To the south, west, and north of the district, sandstone outcrops are few and limited. Heavy faulting bounds The district on those sides and probably there is little if any artesian circulation from those directions. To the east, the La Motte rises to an outcrop area of about 40 square

Jan 1, 1943

By Oliver B. Hopkins

The Peruvian production increased over 3 million barrels from 1933 to 1934—from approximately 13¼ million barrels to over 16¼ million barrels—bringing the cumulative production of the country up to 171 million barrels. Most of this production, as well as most of the increase in 1934, came from La Brea-Parinas Estate, the property of the International Petroleum Co., Limited. In 1932 Peru stood eleventh among the oil-producing countries of the world, but in 1933 her production exceeded that of Trinidad, Argentine and Colombia, which placed her in eighth position. In 1934 Peru's production was exceeded by that of Colombia by about one million barrels, and by that of the Argentine by about 1½ million barrels, thus placing her in tenth position. After several years of relative inactivity in drilling and exploration there was a noticeable increase during 1934 in both of these lines of activity. Oil Fields La Brea-Parinas Estate.—Production on the La Brea-Parinas Estate. reached a significant total of 85,080 bbl. as early as 1891. It increased to over one million barrels in 1912, and to over 10 million barrels in 1929, and in 1934 it reached an all-time high of over 14 million barrels. The total production from 1890 to 1934 was 133,784,609 barrels. Practically all the drilling on the property has been done with cable tools, but during 1934 three strings of rotary tools were introduced. One was a heavy outfit for drilling a deep test and the other two were lighter outfits for deepening wells in the newer section of the field, where the gas pressure was too high to permit safe drilling with standard tools. During 1934 a total of 28,127 ft. was drilled, 66 wells were deepened, and 6 new wells were completed. At the end of the year 2844 wells had been drilled on the Estate, of which 1814 were still productive. The remaining 1030 wells represent abandoned producers or dry holes. The total area that has been productive up to the present time is estimated at 13,369 acres. An interesting article on the various phases of operations of the International Petroleum Co. was written by Arthur Iddings and published in The Oil and Gas Journal (Dec. 27, 1934).

Jan 1, 1935

By J. T. Brown

AS far as could be ascertained, no one had previously investigated the creep strength of silicon poly-crystals. Literature has appeared showing evidence for plastic deformation in silicon single crystals and whiskers.*1"6 Also the fact that germanium, a material of similar crystal structure to silicon undergoes plastic deformation under stress at temperatures above about 60 pct of its melting temperature, has been known for some time.2"4'7 This investigation was performed for the purpose of determining the strength and ductility of silicon polycrystals under creep conditions that would give fairly long times to rupture. PROCEDURE The silicon specimen blanks were obtained by first placing granulated transitor grade silicon (99.999 + pct pure) in a silica crucible. The crucible was surrounded by a graphite susceptor, and induction heating was used for melting the silicon in a vacuum furnace. Blank specimens were formed by freezing molten silicon onto a polycrystalline seed of silicon in a vacuum furnace. The seed was attached to a motor driven revolving rod. As silicon solidified, this rod was gradually withdrawn from the melt. A shape with a contracted center section was obtained by varying the rate of withdrawal from the melt. Specimens for the creep-rupture tests were ground from these "pulled" blanks. Creep-rupture tests were performed in spring loaded machines under constant load at 1800" and 2000° F. RESULTS AND DISCUSSION A test specimen which was sectioned longitudinally is shown in the photomacrograph in Fig. 1. Very little deformation has taken place in the portion of the specimen shown, however, slip lines from several slip systems within the same grain, and deformation band formation was seen. The elongated appearance of the grains is due to the method of growing the specimens. One of the most interesting aspects of the results obtained from the creep-rupture tests was the high strength and the accompanying large amount of ductility. The data obtained is listed in Table I which shows the stress to rupture in 100 hr at 2000°F is between 8000 and 9000 psi. This indicates that silicon's strength at 2000°F is about equal to that of the best commercial super-alloys. It is important to mention that silicon has less than 1/3 the density of iron-, nickel-, and cobalt-base alloys. The usual type alloys for high-temperature applications

Jan 1, 1960

By R. I. Jaffee, H. R. Ogden

AT the present time, there appear to be two conflicting opinions on the solubility of boron in titanium. P. Ehrlich' has indicated from X-ray diffraction work that boron is soluble in titanium up to TiB0.8 (17.8 wt pct, 44 atomic pct). The X-ray diffraction pattern for titanium was found in compositions up to TiB0.05_0.07 (1.1 to 1.6 wt pct); then, without a phase gap, superlattice lines appeared up to TiB0.8 On the other hand, Craighead, Simmons, and Eastwood' have estimated the solubility of boron in both alpha and beta titanium to be less than 0.1 wt pct, based on results of metallographic analysis. In some recent work done at Battelle, results were obtained which shed more light on the titanium-rich end of the titanium-boron system. Iodide-type titanium and high-purity crystalline boron were used in this investigation. The boron was prepared by hydrogen reduction of boron tri-bromide and deposition on a hot tungsten wire. The alloys were prepared by arc melting in an argon atmosphere of 10 cm Hg pressure on a water-cooled copper hearth. The ingots were hot rolled to strip at 850°C. Alloys containing up to 1 pct B could be hot rolled. Those containing 2 pct or more B could not be hot rolled. Metallographically, it was found that a second phase was present in alloys containing as little as 0.4 pct B, and that the quantity of second phase increased with increasing boron content. This is illustrated in Figs. la and lb, which show the microstructures of a Ti-0.4B and a Ti-1B alloy annealed in argon at 850°C. X-ray diffraction patterns of alloys containing 1 and 5 pct B revealed the presence of extra lines which correspond to the superlattice lines reported by Ehrlich.' However, no evidence was found of a shift in the lattice constants of alpha titanium indicating that there is very little, if any, solubility of boron in alpha titanium. This fact, coupled with the fact that the alloys were definitely two-phase, indicates that the extra lines are not superlattice lines, but are more probably the result of a second phase of a hexagonal structure almost identical in cell

Jan 1, 1952

By Ernest Gayford

THIS is a nontechnical paper on flotation, subdivided under three general headings: (1) Definition of flotation; (2) what flotation is now doing in Utah; and (3) what is the future of flotation? . DEFINITION T. A. Rickard defines flotation1 as "the act or state of floating," from the French flottaison, water-line and fitter, to float. The dictionary defines flotation as "the science of floating bodies." The flotation process is a method of concentrating ores by frothing. Weinig and Palmer 2 define flotation as follows: What is the flotation process? Briefly, it consists in the agitation of finely divided ore in water containing bubbles of air or gas, a small amount of oil and, usually, other reagents, soluble and insoluble; under these conditions the small parti- cles of native metals, sulfides, arsenides, antimonides, selenides and tellurides show a tendency to attach themselves to the 6lms of the bubbles, and are thus carried to the surface of the water. The oxidized gangue minerals, such as quartz, feldspar, limestone, hematite, etc., show much less affinity for the bubbles, are easily wetted by the water, and either remain in suspension in the water, or sink to the bottom of the vessel. If the bubbles are sufficiently stable they can be removed, carrying their load of sulfide-mineral particles with them. Thus there can be effected a separation of the two classes of minerals from each other, assuming that the grinding has been sufficient to unlock all of the particles of different composition. The separation does not depend upon differences in specific gravity of the various minerals; in fact, the sulfides are usually heavier than the oxides, and some of the heaviest sulfide minerals are the easiest to float. A particle of mineral may be so large, however, that its weight will counteract its affinity for the film of the bubble. In most cases the ore must be fine enough to pass a screen having at least 48 meshes to the linear inch. Taggart defines flotation as follows : Flotation is a method of wet concentration of ores in which separation of mineral from gangue is effected by causing the mineral to float at or above the surface of a body of liquid pulp while the gangue becomes or remains submerged. The method

Jan 1, 1928

By J. R. Long, T. R. Graham, C. W. Matthews, R. S. Dean

IN a previous paper§ the authors reported on the mechanical properties of a 65 per cent copper, 10 per cent manganese, 25 per cent zinc alloy as compared with similarly processed cartridge brass. Additional investigations by these laboratories, on higher copper alloys, have demonstrated that at lower zinc concentrations even larger amounts of pure manganese may be added to copper-zinc alloys without exceeding the single-phase solid solution limits, and that similar increases in tensile strength, yield strength, and hardness may be obtained without excessive decreases in ductility. Several compositions in this range showed also a decided color change with increasing manganese. The normal "brassy" color was considerably lightened and reduced to a faint yellow cast at 15 per cent manganese. With higher manganese contents the alloys were essentially white and similar in appearance to the nickel-silver alloys. From this work it appeared that it would be desirable to determine more completely the properties of the wrought and annealed white alloys. Accordingly, a more detailed study was planned of an alloy having the composition 70 per cent copper, 20 per cent manganese, and 10 per cent zinc. This alloy remained single-phase throughout the working and annealing cycles of the preliminary tests and appeared to be about the strongest of the white single-phase alloys. The project included also an investigation of additional alloys, deviating from this composition by 5 per cent of each of the three components to evaluate the effects of variation in composition; also a study of the properties of the central alloy made with silicothermic manganese. MATERIAL PREPARATION Electrolytic manganese, wirebar copper, and electrolytic zinc were used for the preparation of the alloys. Representative analysis of the electrolytic manganese seldom exceeds 0.01 per cent iron, 0.02 per cent sulphur and 0.02 per cent lead, with no silicon or aluminum. A typical sample of the silicothermic manganese metal contained 2 per cent iron, 0.81 per cent silicon, 0.i6 per cent carbon, and 0.36 per cent aluminum. Melting and alloying were performed in a high-frequency furnace with magnesia crucibles. Melts were deoxidized with small aluminum additions and cast into 25-lb. slab ingots. Care was exercised in deoxidation to avoid excessive amounts of residual aluminum, which has been found to have significant effects on alloys in this system. All ingots were hot-rolled at 1200° to 1300°F. and then cold-rolled with intermediate anneal-

Jan 1, 1945

By K. R. Garr, D. Kramer, A. G. Pard

EXPOSURE of steels to a fast-neutron flux results in helium generation by (n,a) reactions. The elements Fe, Ni, Cr, and N are major participants in the (n,a) reaction and helium concentrations of up to 5 x 10"5 atom fraction could accrue in fuel clads after a year of service in proposed fast reactors.' Such concentrations of helium can severely reduce the ductility of alloys at temperatures of reactor service. The phenomenon of helium embrittlement has been studied in austenitic alloys which were irradiated with particles as a rapid means of producing significant helium concentrations.2-5 The pres-ent work is a continuation of those studies and is concerned with helium effects in a ferritic stainless steel. I) EXPERIMENT Small sheet tensile samples with a gage length of 0.50 in. and a cross-section of 0.009 by 0.040 in. in the gage length were punched from cold-rolled type 405 stainless steel. The composition of the steel used in this work is given in Table I. Prior to helium injection, the samples were annealed 24 hr at 760°C which caused complete recrys-tallization with a resulting grain size of 40 u. This treatment rendered the alloy completely ferritic and carbide particles, 0.5 to 2 uin size, were present at a density of 1 x 1011 cm-3, Fig. 1. These carbide particles were probably a mixture of the M7C3 and M4C types.6 Helium was injected into the samples by irradiation with a particles from a cyclotron, which produced uniform concentrations through the center two-thirds of the sample thickness. Details of this procedure were previously described.' The average helium concentration, as measured on a gas-source mass spec- 11) RESULTS A) Tensile Tests. The results of the tensile tests are given in Table I1 where the values shown are averages of two samples. There was no significant effect of helium on either the yield strength or tensile strength at 550" or 650°C but an increase in both is apparent at 750°C. Samples with helium showed a 20 pct loss in total elongation at 650°C which increased to a 55 pct loss at 750°C. The uniform elongation is not affected by helium at 550" or 650°C but shows an increase at 750°C.

Jan 1, 1970

By A. M. Nicholas

WheN attempting to lift mill pulp containing a considerable percentage of wolframite, in an ordinary bucket elevator, difficulty was encountered from the tendency of the tungsten minerals to settle, on account of their high specific gravity. Lifts not exceeding 20 ft. (6 m.) could be accomplished without particular difficulty, because there was insufficient time for consolidation of the heavy minerals in the bottom of the bucket; but with higher lifts, the heavy tungsten minerals would settle so solidly that when the bucket turned over at the top of the elevator the contents could be only partially dumped. In this case it was necessary to lift the material a distance of 34 ft. (10m.); hence some means had to be adopted to prevent settling, at least to such an extent that the material could be dumped from the buckets. To reduce the carrying time to a sufficient extent would have required a belt speed of 475 ft. (144.7 m.) per minute, which was not feasible. It was decided to try, by vibrating the belt about midway of its span, to keep the material sufficiently agitated during elevation to prevent settling. Underneath the rising side of the belt was placed a 12-in. (30.48-cm.) idler pulley, 18 ft. (5.5 m.) up in the total lift of 34 ft. The idler pulley was set eccentric by % in. (19 mm.) and it was hoped that the vibration thus imparted to the belt, running at a speed of 280 ft. (85 m.) per minute, would prevent settling in the buckets. It was found that the pressure of the belt on the idler, due to the small inclination of the elevator, was not sufficient to overcome sliding on the idler, and the agitation was insufficient to accomplish the desired purpose. The idler was then connected to the drive shaft of the elevator through an intermediate pulley, gearing down to a speed of 20 r.p.m., so that a positive vibration was imparted to the belt; this imparted enough motion to the belt to prevent settling and the contents of buckets dumped satisfactorily. Protecting Elevator Belts When elevating, from the crusher, a rock which was very sharp and abrasive, considerable difficulty arose from cutting of the belt under-

Jan 1, 1918

By Don H. Baker

THE need for new or improved refractory materials has caused metal phosphides to be given renewed scrutiny. Some metal phosphides show high-temperature inertness, are exceptionally hard, and exhibit a marked resistance to chemical attack. Various metal phosphides have been prepared for study by direct combination of the elements,'-' by reaction of metal or metal compounds with phosphine or phosphorus trichloride,'"' by thermal decomposition of a metallic phosphate or phosphite,"-'8 and by molten salt electrolysis.19 Electrolytic preparation of phosphides of titanium, manganese, and chromium from their oxides is reported in this paper. An externally heated 3-in.-ID by 6-in.-deep graphite cell, that served as the anode as well as a container for the electrolyte, was used in these investigations, and a suspended, centrally positioned graphite rod served as the cathode. A closely fitting silicon carbide furnace liner minimized atmospheric oxidation of the crucible. Electrolyses were performed for predetermined periods and current settings. Preliminary research had indicated the more efficient current and potential settings that could be used. Upon completion of the deposition period, the deposit was hot-stripped from the cathode. The mass of crystalline deposit, plus occluded and adhering salt, was crushed to minus 10 mesh and hot-leached in dilute hydrochloric acid. The leached crystalline material was water-washed, dried, and sampled for analysis. Products were identified by X-ray diffraction and standard analytical procedures. Electrochemical studies were initiated to establish the optimum conditions necessary to produce manganese phosphide (MnP), titanium phosphide (Tip), and chromium phosphide (CrP). Among the factors studied were the operating temperature, the imposed current, and the electrolyte system. If the temperature, or imposed current, was too high, deposition of phosphorus resulted, and if either were too low, partially reduced lower oxides were deposited. The operating conditions established for repetitive high-quality production of metal phosphides of the MP structure are presented in Table I. The metal phosphide crystals varied in size, but all had a definite metallic appearance. Typical are the crystals of CrP shown in Fig. 1. Evaluation data and analysis of the crystals are presented in Table 11. Efforts to measure resistivity of these three compounds over the temperature ranges of 250o to 400°K were hampered by the small physical size of the crys-

Jan 1, 1968

The National Research Council was organized in 1916 at the request of the President by the National Academy of Sciences, under its congressional charter, as a measure of national preparedness. The work accomplished by the council in organizing research and in securing cooperation of military and civilian agencies in the solution of military problems demonstrates its capacity for larger service. The National Academy of Sciences is therefore requested to perpetuate the National Research Council, the duties of which shall he as follows: 1. In general, to stimulate research in the mathematical, physical, and biological sciences, and in the application of these sciences to engineering, agriculture, medicine, and other useful arts, with the object of increasing knowledge, of strengthening the national defense, and of contributing in other ways to the public welfare. 2. To survey the larger possibilities of science, to formulate comprehensive projects of research, and to develop effective means of utilizing the scientific and technical resources of the country for dealing with these projects. 3. To promote cooperation in research, at horse and abroad, in order to secure concentration of effort, minimize duplication, and stimulate progress; but in all cooperative undertakings to give encouragement to individual initiative as fundamentally important to the advancement of science. 4. To serve as a means of bringing American and foreign investigators into active cooperation with the scientific and technical services of the War and Navy Departments and with those of the civil branches of the Government. 5. To direct the attention of scientific and technical investigators to the present importance of military and industrial problems in connection with the war, and to aid in the solution of these problems by organizing specific researches. 6. To gather and collate scientific and technical information, at home and abroad, in cooperation with governmental and other agencies, and to render such information available to duly accredited persons. Effective prosecution of the council's work requires the cordial collaboration of the scientific and technical branches of the Government, both military and civil. To this end representatives of the Government, upon the nomination of the National Academy of Sciences, will he designated by the President as members of the council, as heretofore, and the heads of the departments immediately concerned will continue to cooperate in every way that may be required. THE WHITE HOUSE, WOODROW WILSON. 11 May, 1918.

Jan 7, 1918

By L. C. Morganroth

Discussion of the paper of L. C. MORGANROTH, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 475 to 481. DAVID B. REGER, Morgantown, W. Va.-I notice in the third paragraph of the first page of the paper, that in mentioning the clays of the Pottsville series, the author says: "The bed of clay found in the latter formation is unique in that flint clay is practically restricted to it. (A variety of flint clay is occasionally found in these upper deposits but this is in such small amounts as to be negligible."). If the author wishes to confine himself to the fire clays of Pennsylvania, as the title seems to indicate, I have nothing to say, but if he wishes to include a discussion on fire clays of the adjoining States which the. subsequent paragraphs of his paper seem to indicate, then I wish to call attention to the fact that there are large and extensive deposits of fire clay in the Allegheny series, immediately overlying the Pottsville in the northern counties of West Virginia. These fire clays have been studied carefully, and described in several reports of the West Virginia Geological Survey, first in the report on Ohio, Brooke, and Hancock Counties, in the northern part of the State; described later ,in the report on Monongalia, Marion, and Taylor Counties, and in the report on Preston County, which followed. In these latter counties (Monongalia, Marion, Taylor, and Preston) there are some beds of fine fire clay, varying in thickness from 6 to 10 or 12 ft., with a content of only 2 or 3 per cent. of fluxing ingredients, and these are of the typical Savage Mountain appearance and also have the typical Savage Mountain fracture. They have been prospected, but not mined a great deal. Several of them have been tested in blast furnaces and furnaces for other purposes, in glass-manufacturing plants, also for firebrick, arid have been found to be very good. They are simply awaiting development, and I merely want to call attention to the fact that there are plenty of them in the Allegheny series still above the Pottsville in West Virginia. There are two or three valuable seams which I have seen in person and have had analyzed in our laboratory.

Jan 5, 1916

By T. Wasson

Midland and Isabella counties have been the centers of activities for the year 1932. The major part of the 6,967,000 bbl. produced during the year was obtained from the old Mt. Pleasant field and the Eastern Extension field. The total production to the end of 1932 for Michigan, from all fields since discovery, is 20,679,600 bbl. Production in the Eastern Extension field was obtained from Dundee limestone of Devonian age, at a depth of about 3600 ft. As a result of the year's activity in this area, the limits of the Eastern Extension have been defined. No new fields have been discovered. A number of prospective areas have been drilled and condemned by dry holes. Probably the most outstanding development of the year was the discovery of oil on the Yost farm, in sec. 35 of Greendale Township, Midland County, by the Pure Oil Co., in the early part of December. Production is from the Dundee limestone similar to that in the Eastern Extension but is 4 miles south of that area. The first well has averaged about 500 bbl. per day since completion. It is near the center of a solid block held by the Pure Oil Co., so that rapid development due to competitive drilling is not expected. During the early part of the year the Midland-Isabella area was under proration, but on May 17 proration restrictions were discontinued and remained so until the end of the year. While the Eastern Extension saw the principal activity, some work was done in other fields of Midland and Isabella counties, but very little new production was added. The Vernon field on the north showed a slight increase in production over 1931. The Leaton field decreased. The well in Porter Township, Midland County, is still kept in the production ranks but very little drilling was done in that area. The old Saginaw field, Saginaw County, still remains the only spot in the state where commercial production is obtained from the Berea sand. It showed a slight decline over 1931 with no new producers for the year. The Muskegon field on the west side of the state showed a considerable decline over 1931, but owing to the rejuvenation of some wells by the use of acid this drop was not as great as might have been expected. Only two new producers were drilled in that area.

Jan 1, 1933

By Thomas A. Simpson

THE Birmingham red iron ore district in Jeffer-son County, north central Alabama, Fig. 1, is bounded on the northwest by the Warrior and Plateau coal fields and on the southeast by the Cahaba and Coosa coal fields. The area of study includes the ridge and valley between Red Mountain and Shades Mountain, Fig. 2, approximately 70 square miles extending from Homewood in the northeast to Greenwood in the southwest. The district is one of the most important producers of hematite in the United States, with an annual production of about 7 million tons.' The amount of hematite mined between 1870 and 1950 ranged from 6 to 16 pct of the nation's total annual production,' and the iron and steel products from blast furnaces in the Birmingham district supply the entire southeastern section of the country. Most of the mining in the Birmingham district is from slope mines along the outcrop of the ore on Red Mountain, such as Red Ore, Muscoda, Spaul- ding, and Sloss. The Pyne and the Shannon are the shaft mines of the area. The Shannon mine of Republic Steel Corp., in the central part of the area under study, is in Shades Valley at the foot of Shades Mountain. The Pyne mine of Woodward Iron Co. is 2 miles east of Readers Gap in Shades Valley. The hydrology problem has become more prevalent as mining in the area has progressed downdip. An extensive exploratory diamond drilling program is necessary to determine areas where water pressures and abnormal flows are excessive. This operation, added to higher pumpage rates, has greatly increased the costs of ore extraction. In November 1952 the U. S. Geological Survey began a detailed study of occurrence and movement of ground water in the iron mining areas of the Birmingham district. The study is a part of a small-scale but nationwide program to develop data that will be of help to the mining industry in solving mine water problems. The area of the study, in the Ridge and Valley province of the Appalachian system, Fig. 1, is a series of alternate ridges and valleys trending northeast. The principal ridges are Red Mountain, altitude about 1000 ft, and Shades Mountain, about 1100 ft. Shades Valley is between these two ridges, and its lowest point is about 480 ft. Shades Moun-

Jan 1, 1956

By H. G. Botset

A KNOWLEDGE of the water content of producing sands is becoming of increasing importance to the petroleum industry. It is now a generally accepted fact that practically all oil sands contain some free water. Recent experiments1 have shown that an appreciable fraction of the pore space of a sand may be filled with water while oil production from this sand is water-free. Crowther and Haines,2 in experiments on electro-endosmosis in soils, reported that there was no endosmotic flow of water when the moisture content of the soil was 14 per cent or less, indicating that the moisture content of the soil below 14 per cent was held by dif-ferent forces than the water content above this value. This result is confirmed qualitatively by Dunlap,1 who found that "as the volume of water in the voids exceeds approximately 15 per cent of the pore volume, the permeability of the core to kerosene is markedly reduced." The author3 has also found in other experiments that the gas flow through a water-saturated sand reaches essentially 100 per cent when the pores of the sand still contain from 10 to 15 per cent water. The velocities of the flowing fluid in the experiments cited were comparatively high, so that in practice one may expect, at lower fluid velocities, an even higher moisture content of the sands with water-free oil or gas production. Thus a knowledge of the water content of oil-field sands becomes of con-siderable importance in estimating petroleum and gas reserves, and effi-ciency of fluid recoveries from depleted reservoirs. Rapid and reasonably accurate methods of measuring the water content of sand cores have not been described so far in any literature that has come to our attention.4 The method described below is devel-oped from methods that have been used for some time to measure the water content of alcohols.5,6,7 It is an application of the fact that in the presence of certain organic liquids such as kerosene, carbon tetrachloride, xylol, etc., water and alcohol are only partly miscible. This relation-ship has been used for some time in the study of gasoline-alcohol mixtures where the presence of small quantities of water affect the solubility of

Jan 1, 1938

By A. Andreas

New Mexico, after several years as the sixth ranking oil-producing state, was surpassed by Illinois and for 1939 ranks seventh in the United States. Oil production for 1939 was 36,746,840 bbl. Production for 1938 was 35,510,176 bbl., a gain of 0.033 per cent. Production for the year would have been greater had there been a pipe-line outlet for the Vacuum field. The complete shutdown during the latter part of August covering a period of 15 days meant a production loss of over 1,500,000 bbl. of oil. Daily production allowable as set by the Oil Conservation Commission has followed very closely the recommendations of the Bureau of Mines. It has been found that the recommended allowables as quoted by the Bureau of Mines do not always reflect the actual demand, as there is a considerable lag hetween the recommended amounts and the current demands. During the year the various operating companies have done considerable remedial work in setting packers to reduce the gas-oil ratios in the various fields. Six new fields were discovered in New Mexico during 1939; three in Lea County, two in Eddy County and one in Chaves County. In the early part of 1939 a committee composed of the various engineers and geologists recommended subdividing the old Artesia area into various producing pools. This division was accepted, therefore the total number of producing fields in New Mexico is considerably greater than the number of fields in 1938, but does not represent new fields discovered during the year. The southeastern area continues to he the largest producer of oil. During the year 2,716,551 bbl. were produced in Eddy County and 33,690,996 bbl. in Lea County. Total production ill the northwestern part of the state, which includes San ,Juan and McKinley Counties, was 338,293 bbl. At the beginning of the year the daily average nonmarginal well allowable for Lea County was 48 bbl. At the close of the year it was 49 bbl. The daily average production for the year was 97,313 bbl. During the year, 659 wells were drilled in the state, of which 565 were producing oil wells, 15 gas wells, 6 carbon dioxide gas wells and 73 dry holes. Summarized at meeting; manuscript received at the office of the Institute March 18, 1940. * State Geologist, member of New Mexico Oil Conservation Commission, Santa Fe, New Mexico.

Jan 1, 1940

By A. Andreas

New Mexico, after several years as the sixth ranking oil-producing state, was surpassed by Illinois and for 1939 ranks seventh in the United States. Oil production for 1939 was 36,746,840 bbl. Production for 1938 was 35,510,176 bbl., a gain of 0.033 per cent. Production for the year would have been greater had there been a pipe-line outlet for the Vacuum field. The complete shutdown during the latter part of August covering a period of 15 days meant a production loss of over 1,500,000 bbl. of oil. Daily production allowable as set by the Oil Conservation Commission has followed very closely the recommendations of the Bureau of Mines. It has been found that the recommended allowables as quoted by the Bureau of Mines do not always reflect the actual demand, as there is a considerable lag hetween the recommended amounts and the current demands. During the year the various operating companies have done considerable remedial work in setting packers to reduce the gas-oil ratios in the various fields. Six new fields were discovered in New Mexico during 1939; three in Lea County, two in Eddy County and one in Chaves County. In the early part of 1939 a committee composed of the various engineers and geologists recommended subdividing the old Artesia area into various producing pools. This division was accepted, therefore the total number of producing fields in New Mexico is considerably greater than the number of fields in 1938, but does not represent new fields discovered during the year. The southeastern area continues to he the largest producer of oil. During the year 2,716,551 bbl. were produced in Eddy County and 33,690,996 bbl. in Lea County. Total production ill the northwestern part of the state, which includes San ,Juan and McKinley Counties, was 338,293 bbl. At the beginning of the year the daily average nonmarginal well allowable for Lea County was 48 bbl. At the close of the year it was 49 bbl. The daily average production for the year was 97,313 bbl. During the year, 659 wells were drilled in the state, of which 565 were producing oil wells, 15 gas wells, 6 carbon dioxide gas wells and 73 dry holes. Summarized at meeting; manuscript received at the office of the Institute March 18, 1940. * State Geologist, member of New Mexico Oil Conservation Commission, Santa Fe, New Mexico.

Jan 1, 1940

By W. A. Backofen

THE preferred orientations, or textures, resulting from many of the various methods for testing and forming metals have been the subject of numerous investigations.1,2* Despite this large amount of work, however, only a few limited studies have been made of the texture that is developed by torsional deformation. Ono3 found that in severely twisted wires of copper and aluminum a [Ill] direction lies parallel and a [1101 direction perpendicular to the longitudinal axis of the wire. Sachs and Schiebold4 have reported that a double-fiber texture exists in a twisted aluminum wire with both the [Ill] and [loo] directions parallel to the axis of the wire. Twisted iron wires have also been examined by Ono.8 Both the [1101 and [1121 directions were reported as parallel to the axis of the wire. Goss5 concluded from a study of twisted rods of a low-carbon steel that the preferred orientation existing at fracture is quite complex, but that many grains have a [1101 direction parallel to the axis of the wire. In addition to the earlier experimental work, some suggestions have been made about the possible nature of the torsion texture. These suggestions are based on the results of many experiments which indicate that the cold-working texture of a particular metal is largely determined by the geometrical change in shape that the metal undergoes during plastic deformation.1,6 Hibbard and Yen7 have considered the problem of deformation textures and have presented an analysis which is able to explain why equivalent changes in shape should yield similar textures. Therefore, a knowledge of the principal strains associated with torsional deformation would seem helpful in the interpretation of the torsion texture. The necessary analysis has been made of the state of strain in an element of metal lying in the surface of a cylindrical rod or tube that has been subjected to pure torsion.8,9 This analysis shows that the directions of the principal normal strains rotate continuously within a torsion specimen while it is being twisted. After the first infinitesimal amount of twisting, these directions make angles of 45" with the longitudinal axis of the bar. They rotate from this position as twisting proceeds, and after an infinite amount of twisting, the direction of the principal tensile strain is perpendicular, and the direction

Jan 1, 1951

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I .03 -I.06 Acid number.................. 6-8 Softening point, mercury method 160º-165ºC Iodine value (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 Purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration ennineeru for Combined Metals Reduction CO., obtained U, S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1948

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I .03 -I.06 Acid number.................. 6-8 Softening point, mercury method 160º-165ºC Iodine value (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 Purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration ennineeru for Combined Metals Reduction CO., obtained U, S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1948

The eastern part of the state of Rhode Island on both sides of Narragansett Bay, including the island of Rhode Island, is underlaid with carboniferous rocks which carry veins of anthracite. This formation extends into the neighboring portion of Massachusetts, including the area from the state line, the towns of Mansfield, Brockton and Bridgewater,: and extending probably ten miles east of the latter two towns, to Middlesboro, and to Fall River. In Massachusetts the coal formation extends over nearly the whole of Bristol, and parts of Plymouth and Norfolk Counties. In Rhode Island and Massachusetts the area covered is about 400 square miles. In both states the exact limits of the coal measures cannot be determined on account of a thick layer of drift which overlays it. Along parts of Narragansett Bay, the coal measures outcrop in the cliffs on the west side of Rhode Island, and the presence of coal here seems to have been noted as early as 1760, and in 1768 a patent was granted to parties who "were about to dig after pit, coal or sea coal" at the back of the town of Providence. In 1807-08 Benjamin Silliman, later a geologist, visited some openings,' and in 1808 a mine was opened near Portsmouth, in the northeast part of Rhode Island. Work was done here until about 1814 when the mine was abandoned. No anthracite had been used in New England at that time, all coal used came from Nova Scotia, Virginia or England, and was high volatile bituminous; neither experience nor the means of firing favored the use of the local fuel? This mine was again working in 1827, was again abandoned and operations were resumed in 1847. In 1837 a note in a magazine mentions, "the immense coal mine in Cumberland-about six miles from the city of Providence" as having a shaft 14 ft. in diameter and 80 ft. deep, that the horses then used for hoisting the coal were to be superseded by a steam engine and another shaft was to be sunk. With these improvements 30,000 to 50,000 tons were to be produced the following year at a cost of $1 per ton and a sales realization of $6.1 Hitchcock's report refers to a number of localities in both states where definite knowledge of coal existed. These are:

Jan 1, 1942