Search Documents

By W. W. Gorr, R. Smith, E. H. Wyche

THE combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W? and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. DEVELOPMENT OF THE NEW STEEL For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield 18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators 'then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, o.58; Ni, 7.28; Cr, 17.6o; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1946

By H. C. Miller

THE gas-lift method of flowing oil from wells is the outstanding feature of petroleum technology today. Its forerunner, the air lift, was used successfully first, in the Baku fields of Russia, in 1899, and later in the Gulf Coast fields of Texas and Louisiana and the Kern River field of California. It is still used to a limited extent in certain oil fields. The use of compressed natural gas for lifting oil from wells has supplanted the air-lift method in a measure in those fields where a sufficient quantity of gas accompanies the oil to make the gas lift possible, or where natural gas is plentiful and inexpensive. We find therefore in California, that, natural gas is used at practically every well where a gaseous medium is employed to flow the oil. The use of natural gas has many advantages over that of air. It is possible to recover and save the gasoline from the gas that accompanied the oil to the surface. This gasoline would be wasted if air were used as the lifting medium. Also, certain proportions of air and gas form an explosive mixture that cannot be handled safely by compressors. Another advantage that gas has over air is that gas under pressure is more soluble in oil. Gas in solution in oil reduces the viscosity of the oil that is being produced and causes it to flow more readily through the. tubing and flow lines. The gas lift has made it possible to recover many thousands of barrels of oil from deep wells in California that could not have been produced otherwise. It would not have been economical, had it been mechanically possible to produce such wells as the world's deepest producing oil well (Miley Athen's No. 6, Rosecranz field, California) by any other method of pumping known today. At this well, production is obtained from between 7305 and 7591 ft. and 11 months after completion of the well, production was being maintained on the gas lift it approximately 2000 bbl. a month. The crookedness of the hole, or its diameter and depth will not prevent the successful application of gas-lift pumping when other conditions are favorable.

Jan 1, 1927

By Edward Adarns Richardson

As developed up to the end of the Great War, an airplane was essentially a mechanism of wood and fabric, joined and held together by metal fittings and fastening. The engine and accessories, wire for wheel spokes and other tension members, and the occasional use of metal for inter-plane struts and the shafts of surface controls required some metal, but essentially it was a wood and fabric structure. Attempts had been made to use metal for other purposes, such as struts in the drag-trussing of wing panels and for short interplane struts, and Junkers had produced an airplane of iron in 1915. By 1917 he was using steel tubes and duralumin sheets, securing noteworthy advantages aerodynamically and from the standpoint of weight and upkeep. He was a pioneer along lines in which progress is still being made. Principles of Airplane Construction The loaded weight of airplanes ranges from 500 lb. for the light plane of which we heard so much a short time ago, to about 40,000 Ib. The great majority of planes range from 2000 to 10,000 Ib. Of this weight from 15 to 30 per cent. is for the dividend-earning load. This percentage is so low that every per cent. saved on the rest of the weight increases the pay load from 3 to 6 per cent,. The economic value of every pound that can be saved in designing or constructing a plane is sufficiently great to warrant spending money on refined methods of structural analysis, materials of superior strength properties for a given weight, methods of manufacture which may make possible the use of refinements in structural design, and the like, to an extent unknown heretofore. The weight of the airplane, without fuel, oil and crew, and pay load, ranges from 50 to 65 per cent. of the total weight loaded for planes suitable for commercial use. It is doubtful if the structural weight will ever be brought down to as low as 40 per cent. for commercial planes. The airplane may be roughly divided into: (1) Power plant, which includes engines, radiators, cooling water, oil and fuel tanks, piping, propellers, engine-starting systems, pumps, super-

By William Blauvelt

THE type of gas producer in which the ashes are fluxed and run off as slag was among the very earliest made. Ebelmen built the first one in 1840 at Audincourt, France, only a year after the installation of the first gas producer of which we have record. Charcoal was used as the fuel, with blast-furnace slag and clay is flux. My interest in this type of producer began when as a boy I saw the fluxing producer at Chester, N. J., which was invented by W. J.. Taylor, and described by him in 1881.1 This producer was invented independently by Mr. Taylor to meet the difficulties he experienced in making producer gas for roasting sulphurous iron ores. It will be of interest to review briefly his description of his producer. It was built like a small blast furnace, having a hearth 24 in. in diameter and 24 in. high. The bosh angle was 25° from the vertical; the diameter at the bosh 4 ft. and at the top 3 ft.; the total height 12 ft. The producer contained one water-cooled tuyere 12 in. above the bottom, with a 1.5-in. nozzle.. Depth of the coal above the tuyere; 6 ft. Mr. Taylor mixed the coal with from 30 to 40 per cent. of basic blast-furnace slag to flux the ash. Occasionally some limestone was also used, but never limestone alone, as the use of the furnace cinder gave a larger volume of slag and made it easier to maintain a proper fluidity. . The producer was blown with a small Weimer blowing engine, delivering 300 ft. of air per minute, at from 1 to 1.5 lb. pressure. The slag was tapped every 2 hr. and was black and glassy in appearance. Broken or egg size anthracite was used. The fine sizes of anthracite could not he made to work. Mr. Taylor expressed the belief that bituminous coal could be used if not too fine, but no experiments were made with this coal. Runs were made of four weeks' duration, with no stops or changes. Mr. Taylor reported the following advantages:

Jan 12, 1913

By G. A. Beiswenger

The application of the law of supply and demand to the sale of crude oil is generally conceded, but the motives underlying the buyer's (refiner's) demands are not always obvious to the seller (producer). In some cases this obscurity has led to the conclusion that the refiner may be unnecessarily particular when he selects one crude and rejects another. This preference, however, is very largely the reflection of the refiner's product demands and the quality of the stocks obtainable from the selected crude. The purpose of this paper is to point out critical characteristies of the major classes of refined products and to show how crudes vary in their suitability for such products. With relatively few exceptions, available processing methods and addition agents make it theoretically possible to produce any type of refined product from any crude source, although it may not be economically sound to do so. The widespread application of thermal cracking for converting higher boiling stocks into gasoline is well known. More recently cracking and refining in the presence of catalysts9 have been developed, as well as various processes for polymerizing lighter hydrocarbons into gasolines having desirable characteristics.6 For several years, selective solvents have been applied commercially to refining inferior quality kerosene, Diesel fuel and lubricating oil distillates.3 Improved methods for refining lubricating oils from crude residual4 formerly suitable only for fuel, are now in use and a number of special solvent processes are available for dewaxing lubricating oils to low pour point.5 These improved refining methods have been developed not only to meet the demand for improved product quality but also to enable the refiner to obtain quality products from crude sources that would not yield such products by the older refining methods. In many cases, the utilization of these modern refining tools necessitates an appreciable expenditure for equipment as well as added manufacturing costs, and their application therefore must be justified economically. Despite the availability of such tools, the added processing costs involved and yields obtainable may render their application entirely impractical. To illustrate this point, inspections of typical cuts from various crudes

Jan 1, 1940

By M. G. Corson

UNTIL recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast state, there is no reason for trying to establish precise data regarding the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing temperatures, so there is little incentive to study the properties of the cast shapes -cakes, bars, ingots and billets-for the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This led to four investigations: by E. Seidl and E. Schiebold,1 by P. Siebe,2 by 0. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence of a' wide zone of columnar crystals between the thin layer of fine crystals near the surfaces of the bars and the large but more nearly: equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the casting machine. More recently, cast shapes of copper were investigated by N. P. Allen5 and by C. Blazey.6 Allen examined vertically cast wirebars and horizontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity due to cold-work and anneal, but gave introductively an account of the composition and average densities of the tough-pitch horizontally cast wirebars used. As far as the present writer can tell, no investigation was undertaken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, tough-pitch or otherwise.

Jan 1, 1938

By J. O. Whiteley, C. Dietz

It is difficult to give a refining outline that may be followed for any and all combinations of the platinum metals; different combinations require different methods of attack. This paper does not pretend to go into all of the reactions of the metals of the platinum group, but will outline the commercial refining of platinum scrap. Typical Platinum Scrap As a concrete case, let us take 100 oz. of miscellaneous scrap, made up of jewelry scrap, dental scrap and laboratory ware. This lot will contain some platinum, palladium, iridium, ruthenium, rhodium, gold, silver and copper. The first problem is to get all of the metals in solution. If the scrap is principally platinum, palladium and gold, a treatment with aqua regia is the course to pursue; but if the scrap contains alloys high in iridium or ruthenium, aqua regia will act too slowly. In the case in hand, we are going to presume that we have scrap high in iridium and ruthenium, and proceed accordingly. Obtaining Residue A Place the scrap, together with six times its weight of granulated test lead, in a solid carbon crucible. This crucible may be placed inside a clay graphite crucible packed with charcoal, to prevent the excessive oxidation of the carbon crucible by the furnace blast. Place a tight cover on the carbon crucible; heat gradually to a good red heat and allow it to soak in the heat for 4 or 5 hr. After the leaded mass is cool, dissolve in dilute nitric acid (1-6) on a steam plate or sand bath. This dissolves practically all of the lead and most of the palladium, silver and copper, together with seme of the platinum and rhodium, and leaves the iridium, ruthenium, gold, and most of the rhodium and platinum as a finely divided residue. Siphon off the clear solution and treat the residue with another portion of dilute nitric acid to insure the solution of the lead and copper. The second nitric acid solution is added to the first, and the residue is filtered on suction and washed thoroughly with hot

Jan 1, 1928

By William Sharp

DISCOVERY of new ore in the Eureka district, Nevada, as a result of bold and persistent exploration based on a geologic interpretation of structure has recently aroused wide comment in mining circles. It may therefore be of interest to the profession to have a summary of the historical background and an account of the recent program of development. The mines of Eureka, discovered in the late 1860's, were the first important silverlead mines in the United States. They have a production record of more than fifty-one million dollars.1 After the ore bodies were apparently bottomed in the 1880's, repeated attempts to find new ore were unsuccessful until 1940, when a diamond-drill hole cut a 40-ft width of sulphide ore 1409 ft below the 841-ft level of the Locan shaft. The next hole cut 30 ft, of ore and three additional holes drilled in 1943 and 1944 showed the ore body to be continuous, Shaft sinking to reach and open up the ore body has been in progress since 1945. GEOLOGY Stratigraphy The ore in the Eureka district occurs in a series of Cambrian sediments which is exposed through a thickness of over 6000 ft. The stratigraphic column is as follows:2 [THICKNESS, FI ORDOVICIAN Pogonip limestone (upper part). Thin bedded limestone with some chert. UPPER CAMBRIAN: Pogonip limestone (lower part). Thin-bedded limestone (with shaly limestone and chert).... 425+ Dunderberg shale. Shale (clay and calcareous shale) and thin bedded limestone340+ Hamburg dolomite. Dolomite and limestonegoo+ MIDDLE CAMBRIAN: Secret Canyon shale. Shale and thin-bedded limestone1,035 Geddes limestone. Carbonaceous, flaggy limestone with some shale partings 335 MIDDLE (?) AND LOWER CAMBRIAN: Eldorado dolomite. Dolomite and limestone2,000 LOWER CAMBRIAN: Prospect Mountain quartzite. Quartzite with occasional inter calated conglomerate and shale 1,660+ The Prospect Mountain quartzite has been subdivided into two formations: Upper part, Pioche shale. Shale, quartzite with some intercalated limestone (Lower Cambrian fossils)-200 ft. Lower part, Prospect Mountain quart zite proper-I,460+ft. Total thickness6,695+] Much the most productive of these formations has been the Eldorado dolomite, which yielded more than $42,000,000 at Ruby Hill and an additional amount

Jan 1, 1947

By Theodore P. Holt

The Mines Operating Co.'s plant at Park City, Utah, was designed to treat the low-grade fillings in the old stopes of the Ontario mine. These fillings carry 6 to 14 oz. of silver, 1 to 2 lb. of copper, 0.01 to 0.015 oz. of gold, and a small percentage of lead and zinc. The treatment consists in mixing the crushed ore with coal dust and salt and then roasting in a new type of furnace by combustion of the contained fuel. The roasted ore is leached with an acid salt solution to dissolve the silver, gold, copper, and lead. At present these metals are precipitated together on scrap iron and the product sold to a refinery. The only new feature of importance in this scheme of treatment is the roasting process, which makes possible the chloridizing of ores without any loss of the valuable metals, and at a very low cost. History of the Development of the Process The roasting process- had its beginning in connection with research work at the Utah State School of Mines. N. C. Christensen, Jr., who held one of the School of Mines' fellowships, was engaged in some experimental work on blast roasting. At the same time I was doing some work on the insoluble gold in Mercur base ores. Mr. Christensen roasted some of this base gold ore in his pot furnace, and found that when he mixed a sufficiently low percentage of fuel with the ore, it did not sinter but roasted to a leachable product. We considered this a new application of blast roasting, and proceeded to test out a large number of ores in several different types of small roasters which we constructed.. This experimental work continued well into the summer of 1911. In August, 1911, the Consolidated Mercur Gold Mines Co. installed a small roaster of our design, which we proposed to operate on the counter-current principle, feeding mixed ore continuously on top, and at the same time drawing off the roasted ore from the bottom. By proper adjustment we hoped to maintain a permanent roasting zone near the center of the column, the ore moving downward as roasted. However, we

Jan 1, 1915

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems. It is equally important to realize that most coal mines will require one or more conventional loader setups in the plan of total mechanization. Seam variations, adverse physical conditions, and special designs of main headings for haulage and ventilation, to name only three reasons, may render 100 pct use of continuous miners uneconomical. Of course, this situation may change. In one mine, prior to 1954, machines that ripped coal from the face achieved only average results, as compared to the impressive performance of boring-type units in another coal mine. A boring-type unit was therefore selected for the first mine in the belief that the chance of success would be greater if it were used in a combined cutting and wedging operation, cutting a full face in its forward movement. The miner was located in a part of the mine where a special projection could be readily developed, a solid area scheduled for mining according to the overall progress plan. All openings surrounding the particular area were carefully investigated for the presence of sulfur balls. Fig. 1 (opposite) shows the representative seam section, containing the several pyritic bands 1/4 to 1/2 in. thick; a characteristic Pittsburgh seam parting averaging 5 to 6 in. of slate, coal, and slate; and the occasional py-rite lenses 2 to 3 in. thick. Under normal conventional mining methods, the top 10 or 12 in. and the bottom 4 in. are left in place to offer roof protection

Jan 1, 1958

By J. W. Freeman, R. F. Decker

A microstructural investigation was pursued to establish the mechanism of the pronounced benefits of traces of boron and zirconium on creep properties of a 55 Ni-20 Cr-15 (20-4 MO-3 Ti-3 A1 alloy at 1600°F. The mechanism of improvement of creep properties was found to be a pronounced stabilizing effect of traces of boron and zirconium on the grain boundaries of the alloy. The alloy with low boron and zirconium was subject to rapzd agglomeration of M23 C6 and in the grain boundaries, followed by depletion of y ' and intergranular microcracking at the grain boundaries transverse to applied stress. Brittle fracture then occurred by linking of microcracks. However, additions of zirconium, boron, and boron plus zirconium decreased this tendency in that order, allowing longer creep exposure and higher creep defor.mations before fracture occurred. VERY little information has been published describing the mechanism by which trace amounts of boron or zirconium improve the creep properties of complex nickel-base heat-resistant alloys, although the effect is now well recognized.1-4 Because the phenomenon is so important to properties and the effects are so striking, a study was made of the mechanism in a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 A1 alloy. It was believed that such a mechanistic approach would increase knowledge in theory of alloying and give a more basic understanding of alloy design to resist creep. The basic premise of the study was that boron or zirconium would alter the microstructural characteristics controlling creep and fracture to the extent that the effects could be identified by light and electron microscopy and by electron diffraction techniques. Characteristic of the microstructure of the Ti + Al-bearing nickel-base alloys is the dispersed precipitation of the intermetallic compound Ni,(Al, Ti), the ? ' phase, which is generally con- sidered to be the major source of high creep resistance.5-7 In addition, carbide phases have been identified8-10 and these can alter creep properties markedly.11 Since both the ?' and carbide transformations have been found to control properties, careful attention was paid to the effect of boron and zirconium on these transformations.

Jan 1, 1961

By E. C. Harder

CERTAIN typical characteristics of bauxites, ores of aluminum permit their classification into a number of categories, each of which has special features that enable grouping within it deposits from widely scattered bauxite fields. There may be local variations in conditions that have introduced differences of lesser importance between similar deposits in different fields, resulting perhaps from the influence of factors other than those that have produced the distinguishing features of each of the different groups, but in general the similarity between the deposits in each group is sufficiently striking to make the grouping indicated of interest. Several factors and conditions enter into the decomposition process that results in the development of bauxites and laterites and affects their character. The principal conditions favoring optimum bauxitization are: (1) pres- ence of rocks with easily soluble minerals yielding residues rich in alumina; (2) effective rock porosity, enabling easy access and free circulation of water; (3) normal to abundant rainfall alternating with dry periods; (4) vegetation, including bacteria, advantageously distributed; (5) available sources of appropriate solution and precipitation agencies; (6) a tropical or at least a warm climate; (7) low to moderate topographic relief, allowing free movement of the water table but a minimum of erosion; and (8) long quiet periods in earth history. Assuming that all of these factors are operating to a greater or less degree, it seems that the one that affects most the physical character of the resulting bauxite or laterite deposits is the chemical and mineralogical composition of the rocks that by their decay yield the bauxite deposits. This factor is used in the classification followed in this paper. In the process of weathering of ordinary silicate and carbonate rocks of the earth's crust, whether of igneous or sedimentary origin, it is the minerals of the alkalies that yield most readily to attack. The alkaline earth compounds also offer no great resistance, particularly the carbonates. Thus, among the rock-forming elements, those producing the most insoluble compounds are aluminum, iron, and silicon, together with certain ones of less importance, such as titanium, manganese, and phosphorus. In normal weathering processes such as prevail in temperate regions, the common minerals of rock decay are

Jan 1, 1952

By H. H. Lowry

SCIENCE attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as applied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on dis-coveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the opposite. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accom-plished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 6.1 to 8.3 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in, the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By C. W. Vaupell

The Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resurgence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barccnite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available. Introduction The Huitzuco mercury mines are of interest because of the unusual occurrence of ore in extinct geyser vents and the presence of several rare mercury minerals. Some of the deposits have typical characteristics of the telethermal zone and there is a gradation towards typical epithermal mineralization in depth. Halse,1 Villarel1o,2 Mactear3 and Merri114 have described the geology and the early operations in the district, and Bar-cena5 and Mallet6 have described the rare mercury minerals, livingstonite and barcenite, found at Huitzuco. Location The village of Huitzuco lies in the north central part of the State of (Guerrero, Mexico, 27 km. (16.7 miles) east of Iguala, which is the largest and most important town in the area. Iguala is served by the Mexican National Railways and also by the Mexico City-Acapulco highway. The highway is surfaced from Mexico City to Iguala, a distance of 200 km. (124 miles) by road, and there is a fairly good, level, dirt road from Iguala to Huitzuco. The elevation above sea level is about 1000 m. (3280 ft.). The climate is warm and very dry except during the rainy season, from June to

Jan 1, 1941

By C. W. Vaupell

The Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resurgence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barccnite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available. Introduction The Huitzuco mercury mines are of interest because of the unusual occurrence of ore in extinct geyser vents and the presence of several rare mercury minerals. Some of the deposits have typical characteristics of the telethermal zone and there is a gradation towards typical epithermal mineralization in depth. Halse,1 Villarel1o,2 Mactear3 and Merri114 have described the geology and the early operations in the district, and Bar-cena5 and Mallet6 have described the rare mercury minerals, livingstonite and barcenite, found at Huitzuco. Location The village of Huitzuco lies in the north central part of the State of (Guerrero, Mexico, 27 km. (16.7 miles) east of Iguala, which is the largest and most important town in the area. Iguala is served by the Mexican National Railways and also by the Mexico City-Acapulco highway. The highway is surfaced from Mexico City to Iguala, a distance of 200 km. (124 miles) by road, and there is a fairly good, level, dirt road from Iguala to Huitzuco. The elevation above sea level is about 1000 m. (3280 ft.). The climate is warm and very dry except during the rainy season, from June to

Jan 1, 1941

By Constantine Michalopoulos, Roger C. Van Tassel

Commercial demand for gold in the United States is important. It has a large impact on the total world commercial and overall non-monetary demand. Given the present free market price and our need to import gold, it has a substantial adverse effect upon our international payments position. But, according to most recent estimates, the United States demand is perhaps no more than 20% of the world as a whole. In 1971, United States consumption was estimated at 215.6 tons out of a total of 1,412.1 tons 1. This figure is very close to the 16% figure developed by Consolidated Gold Fields as the average for the years 1968-1970.2 Surveys of both production and use of gold on a world-wide basis are not new. With the bulk of gold production in only a few countries, it has been possible to develop fairly reliable series on gold output. Estimates have been developed on the known reserves of gold and probable output at various prices.3 On the demand side, figures have been somewhat less complete and reliable. The Bank for International Settlements and the Director of the United States Mint have regularly published estimates of commercial use in major industrial countries. The IMF has issued an increasingly comprehensive survey in its Annual Reports. The IMF has attempted to cover all nations-not restricting its efforts to major industrial nations-and has tried to estimate both gold taken for commercial uses (Estimated Industrial and Artistic Use) and for private hoarding. Their method is to begin with data on free world output plus any net sales by the Soviet Union, subtract any additions to world monetary stocks (or add to available supply for any net reductions in world monetary stocks), subtract estimates for commercial demand and have left as a residual an estimate for private hoarding. The method is straightforward and simple but the quality of the data is suspect. Industry sources tend to believe the figures as biased on the low side because of a persistent tendency to underreport gold movements.4

Jan 3, 1974

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By H. W. Hitzrot

The new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addition of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis-charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure—the new fine-ore bin designed and built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work. The many ideas and opinions behind this achievement were all ably organized and executed by the Hollinger milling and engineering staffs, and not a few were directly initiated by them. Excellent cooperation was afforded by the Hollinger staff to the engineers helping to conduct

Jan 1, 1939

By H. W. Hitzrot

The new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addition of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis-charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure—the new fine-ore bin designed and built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work. The many ideas and opinions behind this achievement were all ably organized and executed by the Hollinger milling and engineering staffs, and not a few were directly initiated by them. Excellent cooperation was afforded by the Hollinger staff to the engineers helping to conduct

Jan 1, 1939