Search Documents

By E. O. Wagner, V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pct natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pct of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 1/16 in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F. The necessary heat also can be obtained from 7.5 to 11 cu ft of gas at 2000°F. A description of the design and operation of a pilot plant for flash drying coal dusts is presented. This plant dries 1/16 in. by 0 coal dust in suspension in 1.5 to 2 sec with 600°F gas at a rate of 1300 lb per hour per square foot of column area and operates continuously at an efficiency of about 85 pct. The design and operation of another pilot plant for drying 1/8 in. by 0 coal dusts Is also described. This unit dries coal in the fluidized state using the sensible heat of gases introduced at 2000°F and processes coal at a rate of about 1500 Ib per hour per square foot of grate area at 85 to 90 pct efficiency. Over 90 pct of the bed moisture of low-rank coal dusts can be removed by the methods described. The heating value of lignite can be increased 45 pet and that if subbituminous coal 25 pct in a few seconds. The physical and chemical properties of coal dusts before and after drying are presented in the report, and it is shown that the bulk density of the dried coal is equal to that of the raw coal. This phenomenon makes it possible to ship 25 to 45 pct more heat in a railroad car with consequent savings in freight costs. Introduction For several years the Subbituminous Coal and Lignite Section of the Coal Branch of the Bureau of Mines at Golden, Colo., has been concerned with upgrading low-rank coals by removal of natural bed moisture. These fuels contain 10 to 50 pct total moisture, which reduces their industrial value considerably. In 1938, investigations were initiated in cooperation with the University of North Dakota to study drying of lignite by the Fleissner process with heat derived from high-pressure saturated steam. Two pilot plants were built, and two reports were published giving the results of this work.l,2 It was demonstrated that lump lignite and subbituminous coal

Jan 1, 1950

By J. A. Hren, G. Thomas

A high-temperature stage has been used to study precipitation and dissolution in thin foils of Al-20pct Ag alloy directly in the electron microscope. The results show that the aging characteristics are similar to those observed for bulk materials, and in addition, direct evidence is presented for clustering at the solid solution temperature. The limit of solubility of G. P. zones is-350°C. The heterogeneous precipitation, the growth and dissolution of ?&apos;have been studied in detail. Growth of ?&apos; parallel to the basal planes, occurs by continuous motion of inter -facial partial dislocations. Growth stops at intersecting particles due to formation of sessile a/6 <110> interfacial dislocations. Growth normal to the habit plane occurs by the spontaneous nucleation of partial dislocations on alternate (111) planes and the thickening rate is --10-3= times the lengthening rate. The precipitates dissolve in layers and the final product is a whole a/2 <110> dislocation . The nucleation -growth -dissolution processes are thus completely reversible. Kinetic data obtained from the dissolution rates of ?&apos;particles enable the diffusion coefficient to be determined and the activation energy is found to be 37.5(±4) kcal mol-1, which is that expected for dzffusion of silver in aluminum. The velocity of the interfacial dislocations is thus dependent solely on the rate of diffusion of silver atoms. RECENTLY it was demonstrated that a high-temperature stage could be effectively used in the electron microscope to follow directly the processes of precipitation and dissolution in thin foils of A1-4 pct Cu alloy.&apos; These experiments also provided kinetic data which enabled the diffusion coefficient to be estimated. This new development of electron metallography opens up many fruitful areas of research and it was decided to investigate the aging behavior in thin foils of A1-20 pct Ag alloy, particularly the mechanism of heterogeneous precipitation (i.e., precipitation on lattice defects). This system was chosen because the aging characteristics of bulk specimens are now well known,2"7 and because we wished to obtain more details of the role played by partial dislocations and stacking faults in the nucleation growth and dissolution of the hcp ?&apos; phase. This is of interest for the general case of fcc-- hcp transformations. Part of the A1-Ag phase diagram is shown in Fig. 1. The use of a high-temperature stage also enables a study to be made of the clustering process (formation of G. P. zones) and to determine the structure of the solid solution prior to the usual quenching and aging procedures. It is also possible to obtain kinetic data from measurements of the rates of dissolution of precipitate particles. Unlike the results of previous experiments on A1-4 pct CU 1 where much of the initial precipitation occurred on the foil surfaces, the results on the A1-20 pct A1 alloy were identical to those reported for bulk specimens6,7 and no surface precipitation was ever observed. Thus, it was possible to follow the aging sequence: G.P. zones — ?&apos; — ? directly in the thin foils. This paper is concerned with the formation and dissolution of zones and the ?&apos; phase, and no attempt has been made so far to follow the mode of discontinuous precipitation of ?. I) EXPERIMENTAL DETAILS The high-purity A1-20 pct Ag alloy was prepared by the Aluminum Co. of America in the form of 0.001-in.-thick sheets. These were cold rolled with intermediate anneals to a thickness of 0.0004 in.,

Jan 1, 1963

By Robert L. Marovelli

A recent reorganization placed the health and safety research activities of the Bureau of Mines under a director, Division of Minerals Health and Safety Technology. The new health and safety research organization and its position in the Bureau hierarchy is shown in Table 1.

Jan 11, 1979

By P. Ramachandraraa, T. R. Anantharaman

THE technique developed by Duwez, Willens and Kle-ment&apos; for rapid solidification of molten alloys in small quantities by ejecting them on to a highly conducting substrate with the aid of a shock wave has come to be known as "liquid quenching" or "splat cooling" in literature and has already been applied to alloys of many binary systems.&apos; The very high cooling rates of the order of l060 to 1080 per sec obtained in this technique and the consequent drastic undercooling of the melt have led to such striking results as formation of new amorphous and crystalline metastable phases and extension of solid-solubility limits in many alloy systems. The cooling rates in these experiments can, however, be neither accurately measured nor effectively controlled and hence the occurrence of either more than one metastable phase or appreciable differences in constitution in splat-cooled alloys of the same composition cannot be ruled out.3 In fact, workers in two laboratories have reported formation of two different cubic metastable phases in liquid-quenched Au-Si alloys containing 17 to 20 at. pct si.4,5 The present note deals with some new and interesting results obtained in a Ag-21 at. pct Ge alloy and a Au-27 at. pct Ge alloy subjected to the liquid-quenching treatment at different cooling rates. Two alloys of nearly the same composition had earlier been rapidly solidified by the standard "gun technique" in the same laboratory and shown to solidify in nonequilibrium structures, viz., an hcp phase (a = 2.987Å;c =4.718Å) in the Ag-Ge system6,7 and both hcp (a = 2.885Å; c = 4.754Å) and tetragonal (a = 11.627A; c = 22.491Å) phases in the Au-Ge system.3 Apart from different substrates (copper and stainless steel), different melt temperatures (50º to 500°C above the liquidus), and different capillary sizes (0.4 to 1.5 mm diam) in the "gun technique", slower cooling rates of the order of l050C per sec were also obtained in the present work by replacing the substrate by water at room temperature in a modification of the technique due to Olsen and Hultgren.8 No attempt was made to measure the cooling rate in any experiment. The products varied from fine powder (>40 pct by wt—200 mesh) obtained by quenching in water to thin flakes and foils (11.0 sq mm to 4.0 sq cm) produced by splat cooling. They were subjected to the Debye-Scherrer method of X-ray examination in each case. In case of the Ag-Ge alloy, in addition to the expected metastable hcp phase,6 a coexistent tetragonal phase (a = 5.093,Å; c = 7.009Å) was detected in some experiments. Eight weak X-ray reflections from this phase could be identified, two of them being the same as reported earlier.7 With increase in the cooling rate, the dominant hcp phase seems to be first accompanied by traces of silver or germanium and then either homogeneous or mixed with traces of this new tetragonal phase. The splat-cooled Au-Ge alloy showed generally the expected hcp and tetragonal phases,3 but sometimes traces of germanium were also present. Further, two new tetragonal phases with the following lattice param ters could be clearly identified in samples quenched

Jan 1, 1970

By W. D. Robertson, R. E. Reed-Hill

DEFORMATION of magnesium crystals in a direction parallel to the basal plane has a special significance as a result of the preferred orientation characteristic of cold worked and recrystallized polycrystalline magnesium sheet and extruded rod in which the basal plane tends to lie in or near the plane of the sheet or the axis of a rod. The principal objective of the present study is a determination of the modes of plastic deformation in magnesium single crystals in this orientation. Evidence for nonbasal slip in magnesium has been presented by a number of authors. Schmid and Was-serman&apos; indicated that pyramidal slip on {1011} < 1120> or {1012} <1120> could occur above 225°C. Bakarian and Mathewson2 stablished that the slip system {1011} <1120> operates at high temperatures and that 225°C was a lower limit for pyramidal slip. The latter authors also showed that the critical resolved shear stress for {1011} slip was 400 g per sq mm at 330°C, while that for basal slip was 66 g per sq mm at the same temperature. Thus, at 330°C basal slip should be expected for all orientations except those in which the stress axis lies almost in the basal plane. More recently Burke and Hibbard3 oserved pyramidal slip at 25°C, when the stress axis was 6" to the basal plane and 14" to a <1120> slip direction. The critical resolved shear stress for pyramidal slip was 52 g per sq mm, which is only slightly greater than their value for basal slip (46 g per sq mm). Chadhuri, Chang, and Grant4 have observed non-basal slip in creep tests with polycrystalline specimens in the temperature range 250" to 350°C. The observed slip bands, which were extremely irregular in appearance, can be explained in terms of cooperative slip on {1011} and (1010) planes which have a common slip direction. Prismatic (1070) slip in polycrystalline magnesium was observed by Hauser, Landon, and Dorn.5 It was found to occur at low temperatures (78" and 195°K) and it was accompanied by cross slip in which the cooperating plane was the basal plane. Since prismatic slip occurred only at regions of high stress concentrations, the critical resolved shear stress could not be determined. Experimental Procedure The present work was performed on crystal specimens which were all cut from the same large single crystal. The original cylindrical crystal, 0.5 x 7 in., was grown in a Bridgman type furnace in which the temperature gradient was moved past the stationary crystal in the manner described by Jillson6 and Burke.&apos; High purity magnesium was furnished by the Dow Chemical Co. with the following spectro-graphic analysis in weight percent: 0.003 pct Al, <0.01 pct Ca, 0,002 pct Cu, <0.001 pct Fe, 0.008 pct Mn, <0.001 pct Ni, <0.002 pct Pb, <0.01 pct Si, <0.001 pct Sn, and <0.01 pct Zn. The large crystal was cut into four cylindrical pieces about 1.5 in. long. A flat surface parallel to the basal plane was made by hand grinding with lubricated metallographic paper on one side of each cylinder. In order to prevent bending in subsequent cutting operations, the crystals were supported by

Jan 1, 1958

By J. L. Huitt, IM. L. Slusser, E. E. Glenn, M. L. Slusser

This paper is concerned with: (1) an analysis and interpretation of the filtration characteristics of drilling muds on filter paper, and (2) an interpretation of early stage "filtration" on consolidated synthetic porous media, herein referred to as the "surge loss" period. It is shown that water-loss data can be plotted so as to disclose the existence of a surge period, a non-uni-form cake thickness period, and a constant pressure filtration period. The same periods occur during exposure of consolidated porous media to muds. The data on consolidated porous media indicate that: (1) mud particles bridge pores inside porous media during the surge period, and (2) "filter cake" build-up inside porous media occurs during subsequent filtration. The data also show that the surge loss increases with sample permeability and with pressure differential. INTRODUCTION The phenomenon of mud filtrate invasion into porous sands of a drilling well has been recognized for many years.1,2,3,4 Part of API Code 29 is concerned with the filtration testing of a drilling mud to yield data on this subject. In a number of investigations "plastering properties" of muds were studied,5,6,7,8 "plastering" apparently meaning cake forming properties. In such studies the characteristics (thickness, permeability, and toughness) of the cake and the rate at which the liquid phase of the mud was separated from the solids (filtration rate through the cake, commonly referred to as water loss) were measured or at least considered. From the standpoint of its effect on well productivity, filtrate invasion into "clean" water-wet pay sands (i.e., those containing no clay minerals) may not necessarily be a serious problem. An increase in water saturation in the zone immediately around the wellbore would cause loss of oil permeability. However, in such a system, much of this water may be removed by oil production. If filtration occurs into "dirty" sands (i.e., those containing appreciable clay minerals), clay swelling or other mechanisms may cause losses in oil permeability which cannot be overcome by oil production.&apos;.&apos; The phenomenon of mud particle invasion into the pay sand of a drilling well was considered to be a possible serious factor in the early days of rotary drilling. Opinions varied as to whether drilling fluids "mudded up" and "sealed" oil sands. In 1932 Rubel,9 Gill,10 and Parsons," in separate papers, presented differences of opinion together with some laboratory and field data concerning loss of oil production caused by drilling fluid invasion into pay zones. These papers, and the discussions, furnish a large background on this subject and indicate the very clear thinking of many men at a time when petroleum production technology was in its infancy. Jones and Babson,6 and Silent,&apos; experimentally found that the depth to which mud particles invaded water-saturated sand packs was small (no greater than 1/16 in). Arn-quist12 in 1937 observed loss of water permeability due to invasion of mud particles into water-saturated, consolidated, sandstone samples. Williams and Cannon5 studied the filtra-tion properties of drilling muds and mentioned "sludge" which penetrated a short distance into the water-saturated filtering medium (sand pack). Byck5 concluded that formation permeability had no effect on the plas-

Jan 1, 1958

By E. S. Machlin, Morris Cohen

GRENINGER and Troiano&apos; were the first to establish the fact that the habit planes of mar-tensitic products are usually planes of high indices. In steels containing 0.55 to 1.4 pct C, the habit plane indices are {225}A.* In steels with more than 1.5 pct C and in Fe-Ni alloys, the indices are {259In. The presence of both habits in certain alloy steels has been reported recently." Several investigators"-" have subsequently attempted to provide an understanding of these complex habit relations. Bowles&apos;6 work is the most recent and the most successful. Like Greninger and Troiano, Bowles concluded that the transformation occurs in two steps, the first, a strain (or displacement) that is homogeneous throughout the volume of the martensitic plate, while the second is a strain that is homogeneous only within relatively small portions of the martensitic plate. The first strain yields the measured tilt of the specimen surface, but does not produce the final martensitic structure. This and the correct lattice orientations are achieved by the second strain. Bowles also reasoned that each strain could be described by the motion of a plane of no rotation and no distortion (hereinafter called the invariant plane) in a direction not necessarily contained in the plane.** In applying these considerations to steels with {225}a habits, Bowles found that the habit plane coincided with the invariant plane of the first strain, a result which signified that the atoms move along certain paths during the transformation. Whether this correlation results from the existence of some sort of a plate nucleus6 lying along the invariant plane of the first strain, or whether the invariant plane primarily defines the preferred directions of propagation of the first strain, will be discussed in a later section. There are two obstacles to the general acceptance of Bowles&apos; treatment: 1—it has not been shown that elements of his double-strain analysis are unique, and 2—it is not known whether his treatment applies to transformations yielding the {2591A habit. Unless these two questions are resolved, the correlation between the habit and invariant planes in the {225}A systems might be regarded as coincidental. Experimental Procedure Using a 70 pct Fe-30 pct Ni alloy as an example of a {2591A habit system, preliminary attempts were made to obtain a double-strain solution based on a Nishiyamax** set of orientation relations and on a Greninger-Troianot set, adopting the stereographic technique described by Bowles" who used the Kurd-jumow-Sachstt set in connection with the {225}A habit. These attempts were unsuccessful because the method is essentially one of trial and error and requires either exceedingly good luck or a prior knowledge of the results being sought. Consequently it was decided to measure independently the strain associated with the formation of a martensitic plate as well as the habit-plane indices of the particular plate. By means of matrix algebra, the measured strain was applied to the austenite lattice, whose orientation with respect to the strain was determined, in order to ascertain whether the resultant structure would have the lattice of martensite. This was not found to be the case, and hence it was assumed that the measured strain was the first of two Bowles-type strains, characterized by the motion of an invariant plane. A solution of this displacement was obtained in terms of the invariant-plane indices and the direction of motion of the atoms. Then the second strain

Jan 1, 1952

By E. R. Morgan, J. C. Shyne, V. F. Zackay

NITROGEN used as an alloying element in steel has received increased attention in recent years. Its merit as an austenite stabilizer and hot strengthener has long been recojinized, particularly by European investigators.&apos; Recent work&apos; indicates that nitrogen contents of 1/2 pet or more allow the addition of several percent of ferrite-forming hot strengtheners, such as molybdenum, without subsequent austenite decomposition at elevated temperatures. The room temperature properties of such alloys are characterized by high yield and tensile strengths with excellent ductility, even after cold working, as shown in Tables I and 11. The 1350°F creep-rupture properties of Cr-Mn-Mo-N steels are comparable to those of commercial alloys such as Timken&apos;s 16-25-6, containing 16 pct Cr, 25 pct Ni, and 6 pct Mo, as shown in Table 111. Cr-Mn steel containing 1/2 pet N must be made under pressure if ingot gassing is to be avoided. However, there are difficulties attendant to this practice. Pressure melting restricts the ingot size, and the equipment required is costlier and more complicated than comparable air melting facilities. An effort was made, therefore, to determine more economical methods of adding nitrogen. The pressures generated in centrifugal casting usually range from 5 to 10 atm and are sufficient to prevent the gassing of high nitrogen Cr-Mn steels. A centrifugal casting was made of an alloy containing 16 pct Cr, 18 pct Mn, 2 pct Mo, and 0.73 pct N. A risk, 8 in. diam and 11/2 in. thick, was cast at 1000 rpm. It has been calculated that a pressure of 9 atm was developed at the periphery of the disk at this speed. Metallographic inspection of specimens taken from the disk revealed no gas holes or other defects. The elevated temperature properties of radial and circumferential specimens taken from this casting are given in Table IV. The creep-rupture life of this cast nickel-free austenitic steel was equivalent to that of the wrought Cr-Mn-Mo-N steels. Although centrifugal casting appears to lend itself to the manufacture of high nitrogen austenitic steels, its applicability is limited to relatively small sizes. A process applicable to the production of large ingots of high nitrogen steels is suggested by low carbon rimming steel practice. Gas holes formed during ingot solidification are not detrimental so long as they weld shut during hot rolling. An economic advantage of gassing ingots is the increased ingot-to-slab yield, especially if the ingots are mechanically capped. Also, it is probable that higher nitrogen levels can be achieved with mechanically capped ingots than with hot-topped ingots. A series of gassy heats was made under both atmospheric and higher pressures, as indicated in Table V. Several of the air melted ingots were mechanically capped by chilling the molten ingot tops with a steel plate. The ingots were allowed to freeze in steel molds without hot-tops unless otherwise indicated. A comparison of Table 111 with Table V shows no significant difference in the creep-rupture properties of the gassy and the nongassy ingots after hot work- ing nor between the gassy ingots produced under different conditions. References 1 F. Rapatz: Application of Stainless and Heat Resisting Steels Alloyed with Nitrogen. Sinhl and Eisen ( 1941) 61, pp. 1073-1078. &apos;V. I?. Zackay, J. F. Carlson, and P. L. Jackson: High Nitrogen Austenltlc Cr-Mn Steels. Trans. ASM 119551 48, PP. 509-523.

Jan 1, 1957

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators 1-5 have noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilities6 and by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported&apos; to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of this portion is shown in Table I and an approximate mineralogical analysis is shown in Table II. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of -6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1952

By A. P. Pipilen, M. Weintraub, W. F. Hosford, A. A. 230-000-000-006 Orning

In a study of the principal factors affecting the transport of coal-water mixtures through a centrifugal pump and a pipeline, the interrelation between solids concentration, velocity, and pressure drop was established for a minus 2-in. bituminous lump coal in concentrations up to 48% by weight. Optimum concentrations were found to exist for maximum capacity of a given pipeline and for minimum energy requirements per ton of coal. Coal size degradation by particle fracture took place in the pump; abrasion and attrition to form fines took place in both pump and line. A novel system of studying flow of solid-liquid mixtures in pipelines by the determination of relative sound intensities was developed. The hydraulic transport of minerals is in part an established art and in part a relatively new field of industrial technology. The established art developed especially where the mineral was under water, where water was used in hydraulic mining, or where large quantities of water had to be pumped from the mining site to expose the mineral. Power requirements and limited life of pumps and pipelines, under such conditions, were relatively unimportant. Examples may be found in dredging, and in hydraulic mining and transportation of phosphate rock.&apos; In the design of a coal pipeline the most needed information relates to flow characteristics, power requirements, pressure drop, size degradation, and size segregation as a function of solids-water ratio and size distribution of the mineral. A considerable amount of information has become available concerning pressure drop and energy requirements.2&apos;3 These topics were therefore not studied intensively. Coal degradation, however, has not been clearly delineated. Lammers and coworkers4 showed that coal may be severely degraded in size but did not distinguish between degradation produced in the pump and in the line. It is the primary purpose of this paper to outline techniques used to acquire some of the much needed design data. A full report of the investigation is to be published by the Bureau of Mines at a later date. APPARATUS AND PROCEDURE The apparatus for circulation tests (hereafter referred to as Type III tests) consisted essentially of a loop and a centrifugal solids handling pump, with attendant instrumentation, and coal weighing and feeding equipment. It also included an adequate water supply, as shown in Fig. 1. The selection of 6-in., schedule 40, carbon steel pipe was based on the top size of coal to be used. Assuming that the top size of coal should not exceed 1/3 the inside diameter of the pipe, a 6-in. pipe would accommodate 2-in. coal, a realistic size for transport from the mine face. An 872-ft loop was constructed first. Later a few tests were made with a lengthened circuit of 1361 ft by superimposing an additional loop on the original one. All bends used were of 3-ft radius. A noisemeter microphone, taped to the pipe at various points, but generally about 50 ft downstream of the pump, was used to sense segregation of the coal and the length of slugs of coal in water. To measure the stream velocity, radioactive sources were encapsulated in plastic cubes. The specific gravity of the blocks was adjusted to 1.3 and 1.8 to simulate low ash and high ash coal particles. Their passage through the pipeline was detected by a Geiger counter. Because the repeated circuits of the Type III tests did not permit coal degradation in the line to be distinguished from that produced by the pump, the two

Jan 1, 1964

By D. Harker, E. Epremian

The constitution of the nickel-tungsten system has been studied by a number of investigators, the most recent of which are Ellinger and Sykes.1 On the basis of metallography, electrical resistivity and hardness measurements and some X ray diffraction work, they constructed a consitution diagram (Fig 1). Ellinger and Sykes report a0 for the alpha face-centered cubic phase (nickel saturated with tungsten) as 3.66?.‡ The gamma phase (tungsten saturated with nickel) is given as body-centered cubic, but no value of a. is recorded. At 43 pct tungsten by weight (approximately 20 at. pct) a beta phase is reported, but structure and lattice parameter are not known. Primarily on the basis of metallographic evidence, they conclude that beta is a new phase and rule out the possibility of formation of a superlattice since they- observe a new phase in the microstructure. Grube and Schlecht2 report an ordering reaction in a system similar to the Ni-W (Ni-Mo) and Harker3 has shown that NirMo forms a superlattice upon the pre-existing face-centered cubic lattice of the alpha phase. Elliniger arid Sykes observed a change in the diffraction pattern of a 4.3 pct W alloy upon aging and attributed it to the formation of a new phase. Thus, there appears to be some question as to the character of the beta phase reported by Ellinger and Sykes. The purpose of the present work is to determine precisely the structure and nature of the beta phase in the Ni-w system of X ray diffraction methods. Experimental Procedure One inch diameter ingots of 43.66 pct, 40.15 pct and 34.06 pct .tungsten by weight (19.8, 17.6 and 14.1 at. pct respectively) were melted and cast under vacuum from electrolytic nickel and pure wire filament grade tungsten. The ingots were soaked for 16 hr at 1300°C in a hydrogen atmosphere furnace, then swaged at this temperature and finally drawn to 0.020 in. diam wire. Some of the bar stock was retained in 1/2 in. diam rod for hardness and metallographic studies. Wire samples for diffraction work were sealed in evacuated quartz tubes and subjected to the various solution and aging heat treatments in a hydrogen furnace. X ray photograms were taken in a Debeye-Slierrer camera using copper K radiation filtered by nickel foil. Results X RAY DIFFRACTION The lattice parameters of the alpha and gamma phases at saturation were determined by an X ray photogram of the 19.8 at. pct W alloy after solution heat treatment at a temperature well within the alpha-gamma range above the peritectoid temperature (17 hr at 1150°C—oil quenched). The alpha phase was found to be face-centeted cubic with a. of 3.594 ± 0.001?, while the gamma phase was determined as body-centered cubic with a. of 3.158 ± 0.001?. Exactly the same phases and parameters were ohtained with the 17.6 at. pct W alloy for the same solution heat treatment. Thorough analysis was made of an X ray photogram of a 19.8 at. pct alloy sample in the quenched and aged condition (solution treated 1T hr at

Jan 1, 1950

By A. B. Parsons

This YEAR BOOK, which is sent to every member, contains the roster of officers and the principal standing committees, brief summaries of the proceedings of the Annual Meeting and of the regional and divisional meetings, abstracts of papers published during-the-year, and a classified list of TECHNICAL PUBLICATIONS and CONTRIBUTIONS, as well as an index of all material published by the Institute in 1935 in these separate forms, in TRANSACTIONS and In MINING AND METALLURGY, the monthly magazine. The two volumes published for the Seeley W. Mudd Memorial Fund are also represented by many items in the index. The necrology, which has appeared in the YEAR BOOK for two years past, will be pub¬lished in the. DIRECTORY, in the spring of 1936. Four volumes, 114 through 117, of the TRANSACTIONS are 1935 publications,-the subjects being, in the order named, Petroleum Development and Technology, Mining Geology, Iron and Steel, Founding and Metallography of Nonferrous Metals (Institute of Metals Division). The Mine Plant volume, which was authorized for publication by the Rocky Mountain Fund, and which was offered as an alternative to a TRANSACTIONS volume, was unavoidably delayed. It will, however, be published as a 1935 volume, and will be distributed as early as possible in 1936. The sixth volume in the A.I.M.E. Series, published under the auspices of the Seeley W. Mudd Memorial Fund, is Coal through the Ages, by. Howard N. Eavenson; the seventh, Modern Uses of Nonferrous Metals,. which has twenty-two authors and was edited by Dr. C. H. Mathewson. Also, it was necessary in 1935 to have a second printing of the first Rocky Mountain Fund volumes, published in 1933-The Porphyry Coppers, and .Ore Deposits of the Western States (Lindgren Volume). The papers for the Iron and Steel and Institute of Metals Divisions have been issued as TECHNICAL PUBLICATIONS distributed under the binding Of METALS TECHNOLOGY in the months of January, February, April, June, August, September, October, December. This plan of distribution will be continued in 1936 for these two groups.

Jan 1, 1936

By Martin Coryell

EHRENBERG was the first to publish and direct attention to the peculiarities of the diatomaceous deposit of Richmond; but how and by whom he was supplied with the material for his microscopical investigations, is not generally known; but we may presume W. B. Rogers, formerly State Geologist of Virginia, furnished the material, and may have given the geological position or horizon. O£ these facts we have no available evidence, nor have we any estimate of the thickness of this stratum of diatomaceous or infusorial earth. At the request of a member of this Institute, I have investigated the subject, and offer the following facts as the result, derived principally from information supplied by Mr. John Ott, of the Southern Fertilizing Company, Dr. William Taylor, State Chemist, C. Peticolas, microscopist, Captain Robert H. Temple, civil engineer, Major C. M. Bolton and Mr. C. M. Smith, civil engineers, and formerly engaged in constructing the tunnel under Church Hill, in Richmond. The city of Richmond is generally described as being built on seven hills. This is not the fact, geologically speaking. Originally, there was an immense plateau of land, about two hundred feet above tide, in which a deep excavation was made from the west to east by the James River cutting down to the granite. Opening southward and meeting the valley of the James are various ravines and gullies, in the principal of which are Shockoe and Gillies Creeks. The formation is tertiary, subdivided into all the classified divisions, but at the present moment no one has been found to make this section a special study. Rogers&apos;s early classifications and diagrams, with all their imperfections, are the only published records, and the printed editions are long since exhausted. The city of Richmond is really situated in these ravines of the James, Shockoe, Gillies, and their connections. The profile marked A, Plate V, represents the section of the plateau

Jan 1, 1876

The meeting of the Institute of Metals Division was held in Phila-delphia from Sept. 30 to Oct. 2, inclusive. On Monday evening preceding the meeting, a dinner was held at the Ritz-Carlton Hotel at which many of the former officers of the Division and of the present officers and execu-tive committee were present. The subject of a membership committee was discussed and a motion to appoint such a committee with powers to go over the membership list for the selection of divisional members and to institute plans for additional members was passed. Mr. H. E. Howe and Dr. Johnston of the National Research Council attended the meeting and presented their plans for an Alloys Research Association. Many opinions were voiced as to the practicability of such a scheme and Mr. Howe expressed himself in appreciation of the cooperative thought and efforts given him. On Tuesday morning the Institute of Metals Division joined sessions with the American Foundrymen&apos;s Association and listened to the opening addresses. In the afternoon a boat ride was taken on the Delaware River, visiting the plants of the Cramp Ship and Engine Building Co. and the shipyard of the Emergency Fleet Corpn. at Hog Island. The launching of the boat christened "Afoundria" at 5 p.m. was witnessed by members of the party. The opening technical session was held on Tuesday evening at the Ritz-Carlton Hotel at 8 o&apos;clock. The next session was held at the Ritz-Carlton at 10 o&apos;clock on Wednesday morning and the final session at the same time and place on Thursday morning. The sessions were well attended and the discussion was good. The highly technical nature of some of the papers on the program was of special note. Taken as a whole the meeting was one of the most successful ever held. The follow-ing papers were presented:

Jan 11, 1919

By Martin Coryell

Ehrenberg was the first to publish and direct attention to the peculiarities of the diatomaceous deposit of Richmond; but how and by whom he was supplied with the material for his microscopical investigations, is not generally known; but we may presume W. B. Rogers, formerly State Geologist of Virginia, furnished the material, and may have given the geological position or horizon. OF these facts we have no available evidence, nor have we any estimate of the thickness of this stratum of diatomaceous or infusorial earth. At the request of a member of this Institute, I have investigated the subject, and offer the following facts as the result, derived principally from information supplied by Mr. John Ott, of the Southern Fertilizing Company, Dr. William Taylor, State Chemist, C. Peticolas, microscopist, Captain Robert H. Temple, civil engineer, Major C. M. Bolton and Mr. C. M. Smith, civil engineers, and formerly engaged in constructing the tunnel under Church Hill, in Richmond. The city of Richmond is generally described as being built on seven hills. This is not the fact, geologically speaking. Originally, there was an immense plateau of land, about two hundred feet above tide, in which a deep excavation was made from the west to east by the James River cutting down to the granite. Opening southward and meeting the valley of the James are various ravines and gullies, in the principal of which are Shockoe and Gillies Creeks. The formation is tertiary, subdivided into all the classified divisions, but at the present moment no one has been found to make this section a special study. Rogers&apos;s early classifications and diagrams, with all their imperfections, are the only published records, and the printed editions are long since exhausted. The city of Richmond is really situated in these ravines of the James, Shockoe, Gillies, and their connections. The profile marked A, Plate V, represents the section of the plateau

CONTENTS PAGE Ross, J. M. and WAYLAND, R. G.-Mining Methods at the Homestake. Discussed by Benjamin F. Tillson, R. M. Raymond, I, H. Barkdoll, Arthur Notman 1 EMMEL, RUDOLPH.-Mining Methods in Zaruma District, Ecuador. Discussed by Rudolph Emmel, George A. Packard, Fred Hellmann, R. M. Raymond, Arthur Notman 2 MISHLER, R. T. and BUDROW, L. R.-Methods of Mining and Ore Estimation at Lucky Tiger Mine. Discussed by Fred Hellmann, Benjamin F. Tillson...4 PARK, JOHN FURNESS.-Mining Methods of Jarbidge District. . Discussed by R. S. Lewis : 5 Mining Methods at the Homestake Discussion of the paper of A. J. M. Ross and R. G. WAYLAND, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1408-A, with MINING AND METALLURGY, February, 1925. BENJAMIN F. TILLSON, * Franklin, N. J.--It requires a good deal of timber to operate, especially the caving systems. An important function in mine operations now seems to be forestry and to operate a timber tract in order to insure a supply of timber. By depleting the timber resources of your section, you only increase your costs later when timber must be brought in from the Pacific Coast or the East. Our experience has been that any square-set method of timbering is the most expensive. Timbering for stoping systems, top slicing if you will, although it uses a large volume of time does not require as expensive timbering as the square-set method; also it does not require as long a life for-the timber, so that such wood as birch and maple, which have strength but not long life under the fungus conditions in the mine, may be used. All the drifts in the orebody are thoroughly timbered, and it has required a lot of timber. If we had it to do over, we would spend a lot more money in the development of rock drifts; as a matter of fact, we must ultimately come to that any way.

Jan 6, 1925

By Heinrich Ries

The fusion-point of clay has usually been considered to be influenced chiefly by the quantity of fluxing impurities which the clay contained. Those clays which contain a high percentage of fluxes, such as ferric oxide, lirne, magnesia, and alkalies, fuse at a low temperature. Aside from the percentage of fluxing-impurities, the size of the grains exerts an important influence. Yet, while this fact has, no doubt, been recognized by many, practically no attempts have been made to prove it by actual experiment, although in the case of fire-clays, Prof. H. O. Hofman has rather disputed it. To illustrate the point more clearly, suppose a clay to be made up of a mixture of very refractory grains, such as kaolinite, and some fusible ones. If this clay be heated, the more easily fusible grains will melt first on the surface, and the softening under heat will gradually extend from the surface of the grain to its center. The larger, therefore, the size of the grain, the longer the time required for the heat to penetrate it. Now, if two samples of clay contain the same volume of flux, but of unequal size, the one containing the smaller-sized grains should fuse first, because the fluxing materials are more evenly and thoroughly distributed through the clay, so that they will more or less surround the refractory grains, which tend to act as a framework and hold up the clay-mass when heated. In order to demonstrate the effect of fineness of grain on the fusibility of clay, several mixtures were made up, consisting of white clay and other minerals. The white clay used was a very refractory type from Georgia, the fusion-point of which lay about cone 35 of the Seger series. The mixtures were formed into small bars 1* inches long, and set on a narrow surface, so that the ends were free to bend as soon as the mass softened. They were burned in a Seger gas-furnace.

Jan 1, 1904

By S. J. McCarroll

J. Bruce Clemmer, J. B. Rosenbaum, and C. H. Schack (U.S. Bureau of Mines, Salt Lake City)—We have watched with considerable interest Three Kids development of Manganese Inc. and have been impressed by the ingenuity with which management and staff have solved their many obstinate handling problems. Mr. McCarroll has been lenient in describing the difficulties faced by the company in developing a process for beneficiating Three Kids ore. The operation, equivalent in size to a 20,000-ton sulphide ore plant, is treating a unique ore by a flotation process pioneered by Manganese Inc. Perhaps the magnitude of the conditioning and flotation problems peculiar to Three Kids ore can be better appraised when it is pointed out that two-thirds to three-fourths of the ore is floated in the rougher step and that the four stages of cleaning which follow are equivalent to floating the whole plant feed two to three times. Our experience in both laboratory and pilot plant flotation of Three Kids and other manganese ores leads us to agree with Mr. McCarroll that suitable conditioning is a prime requisite for successful oil-emulsion flotation. The difficulties of proper conditioning were demonstrated in pilot plant processing of Artillery Peak manganese ore at our Boulder City, Nev., experiment station. Over three months of experiments and extensive plant revision were required before satisfactory conditioning was obtained in the 25-ton-per-day plant. Such factors as time, type and intensity of mixing, aeration, surface to volume relationship, and power input are still being studied by the Bureau of Mines in hopes of learning how best to condition manganese pulps for oil-emulsion flotation. Other factors affecting flotation of manganese with oil emulsion also deserve attention. A few of these are the influence of stability and proportion of ingredients in the collector emulsion, the feasibility of grinding

Jan 1, 1955

By Frank Soulé

Secretary E. H. Benjamin, of the California Miners&apos; Association, has proposed and begun, in co-operation with the testing laboratory of the University of California, at Berkeley, a series of tests which should prove of great interest and practical use to all persons making extensive application of steel wire cables, and especially to miners who run them in deep mines. Mr. Benjamin is endeavoring to obtain pieces of cable both new, and old and worn, from every deep mine of importance on the Pacific Coast, together with all the data obtainable concerning their manufacture and particular use. Pieces from each sample will be broken ill the laboratory before mentioned: and as far as possible the effects of winding around drums or pulleys ; of sudden starting and stopping when loaded; of heavy shocks, and of the general wear and tear of the cables, will be ascertained by these tests. The Olsen testing-machine of 200,000 pounds capacity will be used to break the cables, and the rupturing force, in different instances, will be applied slowly and also rapidly, in order to make the tests comparable as far as possible with the practical use of the cables themselves. All information and data available should be obtained for each specimen sent to the laboratory, the name of the manufacturer, the date of making, strength of cable when new and unrusted, as well as the circumstances and conditions of the practical use of the cable. Having this information before us, we shall be able to tell, approximately at least, the effects of age, rust, wear and tear, shocks, etc.; and perhaps be enabled to draw the line of limitation beyond which it would be no longer safe to use a cable of known manufacture. Moreover, by means of such tests we may, perhaps, he able to recommend worn cables for other uses, less severe in character, thereby prolonging the life of their effective usefulness. When we consider the great number of miles of steel cable now in use, and of the greater number constantly being manu-

Jan 1, 1900

By Norman Maxwell

There was more activity in crude production in northwestern Pennsylvania in 1935 than for several years before, resulting in an increased oil production and also in the number of wells completed. Crude -production approximated 16 million barrels for the state, an increase of about one million barrels over 1934. Demand, indicated by refiners&apos; runs to stills, increased proportionally, leaving stocks of available crude at the end of the year at the lowest point since the middle of 1934, when they reached an all-time low. The price of crude varied during the year from a low of $2.02 to a high of $2.27 at the end of the year for Middle district oil. The price of Bradford and southwest Pcnnsylvania oil changed accordingly. The average for the year would be a lower price than in 1934. A summary of the production data for the year 1935 is given in Table 1. In making up this table, 1935 figures were simply added to the table published by S. H. Cathcart last year1. A list of important wildcats is given in Table 2. Bradford Field Approximately 10,000 acres of the proven producing area of the Bradford field is in Cattaraugus County, New York, and it is possible, by differences, to distinguish the Pennsylvania production from the New York portion. The listed production for the Bradford field includes only that portion of the field situated in Pennsylvania, but also includes production from a small pool, locally known as the Mt. Jewett-Kanesholm pool, where the Bradford sand is being developed and flooded in precisply the same manner as that of the Bradford field itself. The Mt. Jewett-Kanesholm pool is not, strictly speaking, an extension of the Bradford field, but inasmuch as it is so closely allied with the Bradford field-—that is, the sand is the same and the production methods are the same—the production and drilling figures include this area.

Jan 1, 1936