Search Documents

By W. A. Backofen, R. L. Fleischer

Single crystal, bicrystal, and polycrystal tensile tests of aluminum at 4.2°K, 77°K, and 300°K have been used to examine the role of grain boundaries in the deformation process. Results indicate that a grain boundary may affect the extent and slope of easy glide. The stage II hardening rate, on the other hand, is independent of the presence or absence of grain boundaries. This conclusion allows the size of the region of multiple slip caused by an incompatible grain boundary to be determined. For the size of bicyystal sample used in this study, multiple slip occurs in about half of the cross section. PREVIOUS studies of the stress-strain characteristics of bicrystals of face-centered-cubic metals have been limited to aluminuml-5 at room temperature. Recent results, however, indicate that the stress-strain curves of single crystals of such metals may be separated into at least three stages6 in which different deformation processes are occurring7 provided testing is done at sufficiently low temperatures.' Since for aluminum a well-defined stage II develops only below room temperature, previous studies have not been able to relate effects of grain boundaries to all of the three stages of deformation. It is therefore to be expected that low-temperature deformation of aluminum single crystals and bicrystals should clarify the effects of grain boundaries on the different processes of deformation. EXPERIMENTAL PROCEDURE Single crystals and bicrystals were grown from the melt by the standard techniqueg with aluminum reported by Alcoa to be 99.993 pct pure. Ridges in the boat were used to guide the grain boundary during growth, assuring that the boundary would bisect the sample.10 The rate of furnace motion during growth was 1.0 cm per hr. During growth zone purification resulted, as evidenced by the ability of the first material to freeze to recrystallize at room temperature following severe deformation. Samples were approximately 4.4 X 6.6 mm in cross section and 103.5 mm in length between grips. Samples were annealed at 635" i 5°C for 40 hr and furnace cooled over a 7-hr period. They were then electropolished in a solution of 5 parts methanol to 1 part perchloric acid at a current density of 15 amp per sq dm for about 30 min at temperatures below 0°C. Tensile testing was performed at 295" (room temperature), 77" (sample in liquid nitrogen), and 4.2"K (sample in liquid helium) on the hard-type machine indicated schematically in Fig. 1. The machine con- sists basically of a tube surrounding a rod; one end of the sample is attached to each member, and the rod is pulled up the tube to extend the sample. The rod is rigidly mounted and is moved vertically by a system described by asinski." The pulling force is measured continuously by an electrical strain gage load cell, and the relative displacement of the tube and rod is also recorded continuously by a soft cantilever beam with electrical strain gages. Maximum stress and strain sensitivities were ±2g per sq mm and * 3-10-5. In all tests the strain rate was approximately 5.10-5 per sec. The thin wires in the tensile apparatus introduce softness, which may be corrected for, however, by measuring load vs displacement with the sample replaced by an elastic member. For loads greater than 15 kg the spring constant is 1.875.106 g per cm. The flexible wires also served to reduce substantially the large shearing forces which may arise in the case of grips having horizontal rigidity.'' As in any gripping system, however, bending moments will arise in the course of deformation by single slip. Engineering stress, s = (load)/(original cross-sectional area), and strain, E = (increase in length)/ (original length), are used for stress-strain curves unless otherwise indicated. Tables list resolved shear stress, T=mo and shear strain ? = dm, where m is the usual Schmid resolved shear stress factor for the primary slip system at the start of deformation. The first group of samples to be described forms an isoaxial set, all of the crystals making up the single crystals or bicrystals having the same tensile axis, the orientation of which is indicated by the cross in Fig. 2. For this orientation the primary slip plane and slip direction make angles of 45 deg with the tensile axis and the Schmid factor m has its maximum possible value of 0.5. Rotations about the tensile axis are indexed by means of an angle 0 between the small-area surface of the samples and the projection of the primary slip direction onto the cross section, as defined in Fig. 3. In single crystals, values of 0 were 0 and 90 deg, while in bicrystals 0 values were (0 deg, 180 deg), (90 deg, 270 deg), and (0 deg, 90 deg) as indicated in Fig. 4.

Jan 1, 1961

By Joseph R. Stephens

Deformation substructures of' polycrystalline tungsten, W-2, 9, and 24 pct Re, and W-3 pct Ta were studied by tra?zsrnission electron microscopy. The stress-strain curve for unalloyed tungsten showed gradual yielding followed by work-hardening. Electron nzicrographs indicated a gradual increase in dislocation density with increase in strain up to 5.0 pct. Dislocations, although frequently jogged, were straight over moderate distances and were in a randorn array. Stress-strain curves for alloy specimens of W-2 and 9 pct Re and W-3 pct Ta exhibited a drop in stress at yielding followed by only slight work-hardening. Electron micrographs of these specimens after strains of 0.05, 0.1, and 0.5 pct revealed no change in dislocation substructure from the unstrained specimens. After 2.0 pct strain, the three alloys exhibited dense networks. W-3 pct Ta was characterized by straight, frequently jogged dislocations comparable with the dislocation structure in unalloyed tungsten after a similar amount of strain. In contrast, W-2 pct Re exhibited dislocations that contained widely spaced jogs, while W-9 pct Re had developed a cell structure after the relatively srnall strain of 2.0 pct. The W-24 pct Re alloy contained a few dislocations after 0.1 pct strain, while after 0.5 pct strain twins were evident. Dislocation slip bands apparently preceded the twins. The stress-strain curve for the alloy indicated that twinning commenced after approximately 0.25 pet strain. These results indicate that the primary effect of low rhenium concentrations (2 and 9 pct) in tungsten is to increase dislocation multiplication after macroyielding by reducing the Peierls-Nabarro force (lattice resistance to dislocation motion). The dislocation bands that precede twins in W-24 pct Re may be caused by localized internal stresses resulting fro a metastable structure, for example, clustering of rhenium atoms. The effect of high rhenium additions (22 a 65 pet* Rproperties of tungsten. Klopp, Witzke, and Raffo5 reported bend transition temperatures as low as -100°F (200°K) for dilute electron-beam-melted W-Re alloys tested in the worked condition. Recrystalliza-tion increased the bend transition temperature, but alloys with 2 to 4 pct Re were still markedly superior to unalloyed tungsten. Fractographic examinations of tungsten and W- 3 pct Re and W- 5 pct Re alloys by Gilbert 6 revealed that these low rhenium alloys showed a greater tendency toward cleavage failure than did tungsten. Garfinkle 7 showed that rhenium additions, up to 9 pct, to (100) oriented tungsten single crystals increased the proportional limit stress and decreased the flow stress and the rate of work-hardening. In addition, while deformation in unalloyed (100) oriented crystals apparently involved both (110)100) and (112) slip, crystals with rhenium contents of 5 andpct or more deformed primarily by (112) slip. The mechanism by which high and low rhenium additions affect the mechanical properties of tungsten is still not well-established. The present investigation was undertaken to determine by transmission electron microscopy the effects of low rhenium additions, 2 and 9 pct, and a high rhenium addition, 24 pct, on dislocation substructure in the early stages of deformation of polycrystalline electron-beam-melted tungsten. Unalloyed tungsten and a W- 3 pct Ta alloy were included for comparison. EXPERIMENTAL PROCEDURES Materials. Triple electron-beam-melted tungsten, W-2, 9, and 24 pct Re, and W- pet Ta were used for this investigation. Chemical analyses of the cast ingots are given in Table I. A description of the starting metal powders and melting and fabrication pro-cedures for unalloyed tungsten and the W-Re alloys is reported.5 The W-3 pet Ta alloy was processed in a similar manner. Compression specimens measuring 0.300 in. (7.6 mm) in length by 0.130 in. (3.3 mm) in diam were machined from swaged rods. All alloy specimens were annealed in a vacuum of 8 x 10- 6 Torr (10'2iVper sq m) for 1 hr at 3600°F (2255°K). The recrystallized grain size ranged from 0.06 to 0.08 mm diam for the alloy specimens. Unalloyed tungsten was annealed at 2400° F (1589°K) for 1 hr to produce a recrystallized grain diameter of approximately 0.12 mm. Specimens were electropolished in a 2 pet NaOH solution to a diameter of 0.125 in. (3.18 mm) to remove surface notches resulting from grinding and to improve reproducibility of t data. The ends o the compression specimens were ground flat, parallel to each other, and perpendicular to the longitudinal axes with 4/0 emery paper. Compression Tests. The compressive stress-strain apparatus used for compression tests is described in detail by Stearns and Gotsky.9 Room-temperature compression tests were conducted at a crosshead speed of 0.01 in. per min (0.25 mm per min).

Jan 1, 1969

By H. Conrad, V. Damiano, J. Hanafee, N. Inoue

The effects of hydrostatic pressure up to 400 ksi at 25" to 300°C on the mechanical properties of three forms of commercial beryllium (hot-pressed block, extruded rod and cross-rolled sheet) were investigated. Three effects of pressure were studied: mechanical beharior under pressure, the effect of pressure-cycling, and the effect of tensile prestraining under hydrostatic pressure on the subsequent tensile properties at atmospheric pressure. For all three materials the ductility increased with pressure whereas the flow stress did not appear to be significantly influenced by pressure. An increase in the subsequent atmospheric pressure yield strength generally occurred as a result of pressure-cycling or prestraining under pressure, whereas either no change or a decrease in ductility occurred. The only exception to this was sheet material, which exhibited some improvement in ductility following a pressure-cycle treatment of 304 ksi pressure. The effects of pressure-cycling and prestraining were relatively independent of the temperature at which they were conducted. Stabilized cracks of the (0001) type were found in hot-pressed specimens and {1120) type in extruded and sheet specimens following straining under pressure. Also, pyramidal slip with a vector out of the basal plane, presumably c + a, was identified by electron transmission microscopy for extruded rod and for sheet strained under pressure. Small loops similar to those previously reported were found after straining at pressures of the order of 300 ksi. THE use of beryllium in structures is limited because of its poor ductility under certain conditions. Therefore, one objective of the present research was to determine if the ductility of beryllium at atmospheric pressure could be improved by prior pressure-cycling or prestraining under hydrostatic pressure. Another objective was to study the mechanisms associated with the plastic flow and fracture of the polycrystalline form of this metal with pressure as an additional variable. Since the early work of Bridgman,1 it has been recognized that many materials which are brittle at atmospheric pressure exhibit appreciable ductility when strained under high hydrostatic pressure. This effect has been reported for beryllium by Stack and Bob-rowsky2 and by Carpentier et al.3 and has been attributed to the operation of pyramidal slip systems with slip vectors inclined to the basal plane while cleavage or fracture is suppressed.4 That such slip may occur simply by the application of pressure alone without external straining (pressure-cycling) is suggested by the results on polycrystalline zinc5 and polycrystalline beryllium,6 where nonbasal dislocations with a vector (1123) were reported. A significant improvement in the ductility of the bee metal chromium by pressure-cycling has been reported.7 On the other hand, limited studies on the pressure-cycling of the hcp metals zinc67819 and beryllium6 indicated no improvement in ductility; there only occurred an increase in the yield and ultimate strengths. The study on beryllium was limited to hot-pressed material. Consequently, additional studies on the effects of pressure-cycling on other forms of beryllium seemed desirable, especially since for chromium some authors10 have been unable to detect any improvement in ductility while others find a large improvement.7 That the ductility of polycrystalline beryllium at atmospheric pressure might be improved by prior straining under hydrostatic pressure was suggested by the known beneficial effects of cold work on the ductile-to-brittle transition temperature in the bee metals. It was reasoned that, by straining under hydrostatic pressure, fracture would be suppressed, and during the propagation of slip from one grain to its neighbor dislocations with a vector inclined to the basal plane"-'4 would operate. Upon subsequent straining at atmospheric pressure, these dislocations with a nonbasal vector would continue to operate and thereby reduce the tendency for fracture to occur, by assisting in the propagation of slip across grain boundaries and by interacting with any cracks that may develop. It was recognized that maximum improvement in ductility would probably occur at some optimum amount of prestrain under hydrostatic pressure. If the pre-strain was too small, an insufficient number of dislocations with a nonbasal vector would be activated; if it was too large, internal stresses (work hardening) might increase the flow stress more than the fracture stress, or incipient cracks or other damage could develop. EXPERIMENTAL PROCEDURE 1) Materials and Specimen Preparation. The materials employed in this investigation consisted of hot-pressed block (General Astrometals, CR grade), extruded rod (General Astrometals, GB-2 grade with a reduction ratio of 8:1), and cross-rolled sheet (Brush S200, 0.065 in. thick). The analyses of these materials and mechanical properties at room temperature and atmospheric pressure are given in Table I. The grain size of the hot-pressed block was 15 to 16 µ, that of the extruded rod 10 to 11 µ, and that of the sheet 7 to 10 µ in the rolling plane and 5 to 6 µ in the thickness, all determined by the linear intercept method. Al-

Jan 1, 1969

By N. J. Grant, D. S. Bloom

N recent reports, Sully' and Beck and coworkers' I have advanced hypotheses concerning the formation of the phase. Both of these hypotheses are based on Pauling's theories of the electronic configuration of the elements of the first transition group. Sully considered that the number of electrons which can be absorbed in filling electron "holes" is the factor which determines whether or not the structure can form. Beck suggested that the presence of a certain concentration of electron "holes" is the controlling value. It can be shown that a similar criterion can be developed without making reference to Pauling's theories. Table I shows the elements of the first transition group and the incidence of the a structure in the binary systems of these elements according to the data presently available. Also appended is the number of electrons considered to exist in the 3d-4s levels of these elements. If the atomic percentages for the phase are listed as shown in Table 11, and if the number of electrons in the 3d-4s levels per atom is calculated for the a boundary values, the results are as shown in the last column. It can be seen that the numerical values are all in the vicinity of 7 electrons per atom. This is true also for the ternary Cr-Mo-Ni IT phase, which occurs in a system in which none of the binary compositions are known to develop the phase. In the Fe-Mo binary, the high temperature a phase, which occurs at a composition of 50 atomic pct of each element, also yields a ,;1 e of 7 electrons per atom. From inspection of Tables I and 11, it develops that any series of sequential numbers which is assigned to the elements under consideration will result in the numbers pertaining to a compositions grouping themselves around one specific number. It does not follow, however, that this random number necessarily has physical significance. Such a point has already been discussed by Hume-Rothery." One interesting point develops from this study, however, and that is the position of manganese with reference to the other elements and to the phase. In the system used here, the formation of phase is associated approximately with the value of 7 electrons per atom, which is also the number of electrons per atom that manganese has. Manganese, it will be recalled, exists in three different crystal forms, none of which are the usual, simpler metallic forms; on the other hand, elements just to the left of manganese (in Table I) generally have lower coordination-number structures (body-centered cubic) than do elements to the right of manganese (face-centered cubic). The contribution to a complex crystal structure by the interalloying of elements from opposite sides of manganese is significant in that the a phase is formed in binary systems including one element from each side of manganese, with manganese capable of participating with both sides. It is indeed an interesting coincidence that manganese, with 7 electrons per atom, solidifies in complex crystal forms, and that when alloys of the transition elements are made which have seven 3d-4s electrons per atom, they, too, tend to assume a complex crystal form. From the above, it might be deduced that the study of the a phase might be advanced by a critical examination of the element manganese and how its structure is affected by small additions of elements which change the 3d-4s electrons per atom number. The role of atom size would also be of interest in formation. References ' A. H. Sully: The Sigma Phase in Binary Alloys of the Transition Elements. Journal Inst. Metals (1951) 80, Part 4, p. 173. 2 S. Rideout, W. D. Manly, E. L. Kamen, B. S. Lement, and P. A. Beck: Intermediate Phases in Ternary Alloy Systems of Transition Elements. Trans. AIME (1951) 191, p. 872; Journal of Metals (October 1951). "W. Hume-Rothery, H. M. Irving, and R. J. P. Williams: The Valencies of the Transition Elements in the Metallic State. Proc. Royal Soc. (September 1951) 208A. p. 431.

Jan 1, 1954

By M. M. Fine

Normally the U. S. produces less than 10 pct of its annual manganese requirement. About 95 pct of domestic consumption is used by the steel industry.' The strategic and critical nature of manganese has been recognized by its inclusion in the national stockpile and by intensified research directed toward cataloging and evaluating domestic manganiferous deposits. The USBM has participated in these activities for many years with field and laboratory studies to assess the extent and potential utilization of domestic manganese ores. One area of particular interest is in the vinicity of Batesville, Ark., where deposits have been mined since 1849 for both manganese and ferruginous manganese ores. Production is centered in Independence County, but deposits are also found in Sharp, Izard, and Stone counties in north-central Arkansas. Miser has described the geology and manganese mineralization in some detail.'. * "he rocks of the area are sedimentary, consisting of sandstone, limestone, shale, and chert. The two formations of greatest importance,' Fernvale limestone and Cason shale, are host rocks of the primary manganese mineralization. Through 1955 the district produced some 230,000 long tons of manganese ore (35 pct Mn or more) and 236,000 tons of ferruginous manganese (10 to 35 pct Mn).5 Most of the ore has been mined from deposits of manganese oxides in residual clays resulting from weathering of the two formations noted above. Concentration methods have been primitive, consisting for the most part of washing. hand picking, and jigging. A significant accomplishment in the district in recent years was the USBM recognition and investigation of the huge manganese potential represented by unaltered Fernvale limestone. systematic reconnaissance of manganiferous limestone and other occurrences has been in progress since 1953 to delineate the extent and tonnage of manganiferous materials. Results of that survey have appeared in two recent publications,1-5 which ascribe to the district an inferred reserve of 166 million long dry tons at a grade of 5 to 6 pct Mn. Most of this was mancaniferous limestone with an estimated content of 5 pct Mn. Specifications: Beneficiation was carried out on a group of manganiferous limestones to develop a way to recover commercial-grade concentrate from this extensive resource. The following chemical specifications were established by the GSA for metallurgical manganese ore acceptable for delivery to the national stockpile: Size specifications were not considered, as it was assumed that the concentrates could be pelletized or sintered. Manganiferous Limestones: Of the 11 samples tested to date, six were taken by cutting vertical channels across beds of limestone outcrops. Diamond drilling through overlying barren chert into unex-posed limestone provided four samples, and the last was a churn drill sample. In general, the samples were dlrk, fossiliferous limestone containing small amounts of braunite, hausmannite, rhodochrosite, massive and micaceous iron and manganese silicates, quartz, barite, and glauconite. The braunite and other manganese oxides partly to completely replaced some of the calcite and fossil material. The calcite was generously stained with mangenese and iron oxides. Phosphorus was present in all samples as collophanite grains, calcium phosphate fossil replacements. or an unidentified manganese-bearing carbonate. The difficulty in separating this complex array of minerals was further complicated by a very intimate association. Although some manganese grains as large as Ik in. were noted, grinding to subsieve sizes would have been necessary to liberate the components. Figs. 1 and 2 are micrographs, at X100, of typical polished sections in which white areas are manganese. gray is gangue, and black areas are surface depressions. By comparison with the 100 mesh opening, it is seen that some of the grains are coarse enough to respond, perhaps to tabling or flotation, but many are obviously beyond the scope of ohysical processing. Partial chemical analyses of the eight samples that were ultimately amenable to concentration are presented in Table 1. BENEFlClATlON RESEARCH Tabling: To take advantage of the presence of sand-size grains, both jigging and tabling were considered at the outset. Jigging was largely ineffective, but tabling achieved a partial recovery from most samples. As an example, the surface material from Baxter Hill was crushed to —28 mesh, hydraulically classified, and the coarsest spigot fraction was tabled to yield a concentrate, middling. and tailing. The latter two were reground to pass 48 mesh, combined with the primary fines, re-classified, and retabled. The middling and tailing were again ground, this time to pass 150 mesh, and deslimed at 20µ in a 3-in. hydraulic cyclone. The cyclone underflow was returned to the table to reclaim a small amount of high-grade manganese. An interesting facet of the gravity concentration developed on certain samples in which braunite was the principal manganese constituent. Since braunite has a Mohs hardness of 6 to 6.5, while the host rock, limestone. is only 3, a differential size reduction took place during crushing, and the

Jan 1, 1960

By L. C. Brown, S. K. Behera

The diffusion rate in Ag-Sb couples is sensitive to con~pressive load with the width of Ag3Sb, the only phase present in the diffusion zone, increasing with stress up to 800 psi and remaining constant above this. Kirkendall marker experiments show silver to diffuse much faster than antimony in Ag3Sb and incipient porosity may therefore develop at the Ag/Ag3Sb interfnce restricting the transfer of atoms from the silver into the diflusion zone. Application of compressive stress reduces the tendency for porosity to develop and so increases the growth rate. In a recent paper Brown et al.1 observed a significant increase in the thickness of Cu2Te in Cu-Te diffusion couples on application of a compressive stress as low as 20 psi. Similar stress effects have also been observed in the Fe-A1,2 Al-u,3 arid cu-sb4,5 systems. It has been suggested that the increase in growth rates of intermetallic phases in these systems is due to a decrease in the amount of Kirkendall porosity with applied stress. In the present paper, results are presented of the effect of compressive stress on diffusion in Ag-Sb, together with a detailed examination of the Kirkendall effect. The Ag-Sb phase diagram6 shows that antimony has a moderate degree of solid solubility in silver, 5.7 at. pct at 350°C, but that there is essentially no solubility of silver in antimony. There are two intermediate phases— (hcp7) from 8.8 to 15.7 at. pct Sb and Ag3Sb (orthorhombic8) from 21.8 to 25.9 at. pct Sb. EXPERIMENTAL Diffusion couples were prepared from fine silver of 99.95 pct purity and from antimony of 99.7 pct purity. Both the silver and antimony were produced in the form of discs 1/2 in. in diam by approximately $ in. thick, with surfaces ground flat to 3/0 emery paper. Diffusion anneals were carried out in the apparatus previously described.1 A compressive load was applied to the diffusion couple through a lever arm system, with a reproducibility estimated to be ±10 psi. All runs were carried out in a protective hydrogen atmosphere. Following the diffusion anneal specimens were sectioned and polished and the width of the diffusion zone was measured metallographically. Composition profiles were measured using an electrostatically focused electron probe with a spot size of 10 , counting on Sb L radiation. Corrections for matrix absorptiori and fluorescent enhancement9 were not required. S. K. BEHERA, formerly Graducate Student, Department of Metallurgy, University of British Columbia, is now Postdoctoral Fellow, Whiteshell Nuclear Laboratories, Atomic Energy of Canada Ltd., Pinawa, Manitoba. L. C. BROWN, Junior Member AIME, is Associate Professor, Department of Metallurgy, University of British Columbia, Vancouver, B.C., Canada. Manuscript submitted June 14, 1968. IMD RESULTS Fig. 1 shows an electron probe traverse of a typical diffusion zone. In all couples examined only one intermediate phase was observed and the composition of this phase, 23 wt pct Sb, was in good agreement with the composition of Ag3Sb, 23 to 28 wt pct Sb. The presence of this phase was confirmed by X-ray diffraction of filings taken from the diffusion zone. The probe traverses showed no detectable solid solubility in either the silver or the antimony although the phase diagram indicates that some antimony, up to 6.5 wt pct pct Sb, should be in solid solution in the silver. However the width of this portion of the diffusion zone would be expected to be very small in view of the low diffusion coefficient in the silver, 4 x 10-l6 sq cm per sec at 350°C, 10 compared with that in the Ag,Sb, estimated as 3 x 10-8 sq cm per sec in the present work, and this region would therefore not be expected to be seen in the probe traverse. Application of stress resulted in a significant increase in the width of the diffusion zone, Fig. 2. At 350°C, the thickness of Ag3Sb increased from 250 at 0 psi to 400 p at the limiting stress of 800 psi, indicating an apparent 150 pct increase in the diffusion coefficient. Similar behavior was also observed at 400°C, indicating that the stress effect is not characteristic of just one temperature. The growth of Ag3Sb at 350°C and at various stresses is shown in Fig. 3. In every case the growth rate was parabolic indicating diffusion control. The kinetic curves all passed through the origin showing that delayed nucleation of Ag3Sb was not responsible for the stress effect and that it was a real growth effect. A series of tests were carried out in which diffusion was allowed to take place at a lower stress following an initial high stress diffusion anneal. Speci-

Jan 1, 1969

By F. F. McINTOSH

STEEL is a general name applied to the alloys of iron and carbon. These alloys always contain , other elements such as manganese, silicon, sulfur, and phosphorus. Manganese and silicon are usually considered to be alloying elements. Sulfur and phosphorus are regarded as impurities. Tradition has damned them both and, in addition to classifying them as impurities, has established the general impression that many of the ills of steels are the result of the presence of one or both of these elements. Metallurgists are inclined to question the soundness of this tradition. The fact that one blast-furnace plant is devoted entirely to the production of ferro-phosphorus which is used to rephosphorize basic open-hearth steel, and that sulfur is added to many heats of steel, indicates that these so- called impurities might also be classed as alloying elements, and that the tradition which damns them may not be altogether fair and well founded. A critical search through the technical literature on the effect of phosphorus on steel will disclose many references to its harmful effect. Most of these are general in character, but there has been a strong tendency to accept this traditional belief in the harmful effect of the element.

Jan 1, 1926

By EL HANAF

The exploratory program initiated in Egypt in 1937 by four major oil companies was well under way early in 1939. Extensive gravity-meter surveys were carried out in the Sinai Peninsula and the Eastern and Western Deserts. Seismic and magnetometer work vas conducted on a restricted scale. The data collected justified wildcat drilling on structures located geophysically and/or geologically.

Jan 1, 1946

By W. H. Porter, M. E. Wadsworth, J. R. Lewis, K. L. Leiter

The oxidation of Cu2S in oxygen and the sulfating of Cu2O in oxygen-sulfur dioxide atmospheres was carried out under a variety of conditions. The oxidation of Cu2S was found to be retarded by entrapment of SO, and O2, which stabilized internal sulfates for long periods of time. The course of the reaction was followed by measuring weight changes and also by SO, evolution. Sulfating of Cu2O was a maximum at ratios of SO, to O2 approximating maximum SO, production. At elevated temperatures SO, was found to increase the rate of oxidation of Cu2 O to CuO even though sulfates did not form. All sulfating reactions followed the parabolic rate law indicating diffusion. MANY studies of the roasting of copper sulfides have been reported in recent years. Diev et al.1 investigated the roasting of chalcocite (Cu2S) in air, and oxygen enriched air. Lewis et al.2 also studied the oxidation of natural and synthetic chalcocite in air and oxygen atmospheres and their studies indicated that the maximum formation of water soluble sulfates occurred at approximately 450oC. Ashcroft3 reported that oxide production during the roasting of chalcocite resulted only from secondary decomposition of sulfates which were formed as primary products. peretti4 refuted this claim by showing that a layer of Cu2O appeared directly adjacent to the Cu2S during roasting of cylindrical briquettes of cupric sulfide, CuS. The linear advance of the Cu2S-Cu2O interface was used as a measure of the kinetics of the roasting reaction. The reactions proposed were: 2 CuS—Cu2S + 1/2 S2 [4-1] 1/2 S2 + O24 SO2 [4-2] cuzs +3/2 O2 4 Cu2O + SO2 [4-3] cu2o + 1/2 O2—2 cuo [4-4] At temperatures above 663oC, CuO was the only final solid phase reported. Below 663" C increasing amounts of sulfate were found mixed with the CuO. McCabe and Morgan5 investigated the roasting of discs of synthetic chalcocite and reported the following sequence of products beginning at the sulfide surface: Cu2O, a mixture of Cu2O and CuSO4, Cum,, CuO . CuSO4, and CuO. The principal reactions were reported to be: Cu2S + 3/2 O2-Cu2O + SO2 [5-1] CU2O + 2 SO2 + 3/2 O2—2 CUSO4 [5-21 2 CUSO4— CUO . cum, + SO3 [ 5-31 cuo . cuso4—-2 cuo + SO, [ 5-41 Eq.15-11 supports the claim of Peretti, Eq. [4-31, that CuzO is formed directly from Cu2S rather than as a secondary product from a sulfate as suggested by Ashcroft. On the other hand CuO was found to form as a secondary product from the decomposition of copper sulfate and basic copper sulfate, Eqs. [5-31 and [5-41. The formation of sulfates was explained by McCabe and morgan5 to be a direct reaction of Cu2O with 0, and SO, or SO, at distinct regions in which the partial pressures of each were such as to form the sulfate. Thornhill and pidgeon6 roasted both natural and synthetic chalcocite grains in air at temperatures between 420" and 550° C. They found a dense primary oxidation layer in contact with the sulfide. A secondary layer of porous oxidation products was found to expand with roasting time. The oxide products were leached away and the remaining core was studied by X-ray diffraction. The X-ray patterns showed an increased conversion of chalcocite to digenite with time. Digenite,7 a defect structure of cuprous sulfide, occurs naturally as Cu,-,S where x = 0.12 to 0.45, with an average analysis of Cu, ,S. The mechanism of digenite formation was proposed as: Cu2S + oxygen—Cu1-8S + 0.1 Cu2O [6-1] Cuj.eS + oxygen—0.9 Cu2S + SO2 [6-2] It is apparent from the above studies that the oxidation of Cu2S, ultimately ending in CuO, may be divided into ihree general stages (all of which may occur simultaneously): 1) primary oxidation to Cu2O; 2) secondary sulfate formation; and 3) sulfate decomposition. Consequently reactions of O2 and SO, with Cu20 constitute important aspects of the roasting of chalcocite. Virtually no studies have been made regarding sulfating reactions involving Cu,O. Mills and Evans8 noted the effect of sulfur dioxide on the oxidation of copper at low temperatures and low SO, partial pressures. They reported a measurable increase in the oxidation rate of copper when SO2, was present. Interest in the Cu2O-CuO-0, system has been limited predominantly to misciblllty studies and determinations of heats of formation by

Jan 1, 1961

By Oliver Bowles, Carl A. Gnam

THE construction industry normally contributes extensively to the general economic welfare of all sections of the country. Billions of dollars are spent for materials and labor, and the success or failure of many business enterprises depends upon the volume of construction. The steel, aluminum, copper, cement, brick and tile, lime, gypsum, stone, sand and gravel, and several of the less prominent mineral industries are vitally concerned. Of great interest, therefore, is the accumulation of needed construction following the relative inactivity of the past five years, the recent moderate revival in building, and the prospect of a broader and more definite upturn. One may judge the magnitude of possible expenditure for construction by what has occurred in the past. The peak years were 1925 to 1928, inclusive, when the annual values of con- tracts awarded amounted to over six billion dollars. In marked contrast was the 1933 total of about 1% billion, the lowest level shown in the Federal Reserve Board Index, which goes back to 1919, and the more favorable 1935 figure of about 1.7 billion. An increase of nearly four billion over the 1935 volume would be necessary to equal the peak year 1928.

Jan 1, 1936

Discussion of the paper of COURTENAY DEKALB, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 331 to 337. HORACE V. WINCHELL, Minneapolis, Minn.-Mr. Dehalb summarizes the reasons which he believes are important for the revision of the mining laws, as follows: "1. The conceptions as to the characteristics of orebodies that were held at the time the statute of 1872 was enacted have since proved to be in many respects erroneous." We all appreciate the force of that suggestion. The idea of the old prospector who made rules and regulations in the early days, which were attempted to he incorporated, so far as possible, in the Mining Act of 1872, was that all of the veins in a certain district outcropped upon the surface, or approximately parallel to each other upon the surface, and maintained that parallelism beneath the surface. Therefore, it seemed perfectly proper and natural for each man to stake his claim upon an outcropping, and have the right to follow that vein in working downward, with the general expectation that his workings would always remain just as far away from those of his neighbor as the outcroppings upon the surface. This does not happen to be the case. Dr. Raymond has very ingeniously referred to the subject in one case, in words which read as follows: "If all mining properties presented this beautiful simplicity of structure (ideal location of ideal vein), and all mining locators exhibited a corresponding simplicity of purpose, the application of the law would be easy, but the naiveté of the statute fares badly between the freaks of nature and the tricks of man."

Jan 5, 1915

By Joseph Fry, Ralph H. Espach

In the spring of 1943, when it was evident that the Tensleep bandstone in the Elk Basin Field, Wyoming and Montana, held a large reserve of petroleum, Bureau of Mines engineers obtained samples of oil from the bottom of nine wells and analyzed them for such physical characteristics as the volumes. of gas in solution. saturation pressures or bubble points, shrinkage in volume caused by the release of gas from solution, expansion of the oil with decrease in pressure, and other related properties. The composition of the gas in solution in the oil was studied. The pressures and temperatures existing in the reservoir and the productivity characteristics of the oil wells were determined. The data obtained indicate that the oil in the Tensleep Reservoir of the Elk Basin Field has unusually varying physiral characteristics, such as a saturation pressure of 1,250 psia and 490 cu ft of gas in solultion in a barrel of oil at the crest of the structure and a saturation pressure of 530 psia and 134 cu ft of gas in solution in a barrel of oil low on the flanks. The hydrogen sulfide content of the gas in solution in the oil varies from 18 per cent for oil on the crest to 5 per cent for oil low on the flanks of the structure. Of even greater significance is the fact that these and other variable characteristics of the reservoir oil are related to the position of the oil in the structure. Many geologists and petroleum engineers have considered that all the oil in a petroleum reservoir has rather uniform physical characteristics and that equilibrium conditions prevailed in all underground accumulations of oil and gas; that such is not always so is borne out by the results of the study by the writers. INTRODUCTION The Rocky Mountain region is one in which may be found striking examples of the unusual in oil and gas accumulations, as is evident from the following: The high helium content (7.6 per cent) of the gas in the Ouray-Leadville limestone sequence in the Rattlesnake Field, New Mexico, and gases of similar helium content in other fields; 50" to 55' API gravity distillate in solution in carbon dioxide gas and recoverable through retrograde condensation, in the North McCallum Field, Colorado; the occurrence of gas, oil, or both in closely related structures contrary to the usual concepts of gravimetric segregation: the accumulation of gas and/or oil in structures closely related to other structures that apparently are more favorable but do not contain oil or gas accumulations; the high hydrogen sulfide content (as high as 42 per cent) of the gas associated with oil in some fields in the Big Horn Basin, Wyoming; and the wide range of fluid chararteristics found in the Elk Basin reservoir. Elk Basin, an interesting old oil field that has been producing oil from the Frontier formation since 1915, is situated in a highly eroded basin resulting from the erosion of the crest of an anticline and some of the underlying softer shales. The field came back into national prominence during 1943 when it became known that it was the largest single reserve of new oil discovered in the United States that year. The Tensleep sandstone was found to contain oil in November. 1942, when a well drilled to a depth of 4,538 ft (44 ft into the Tensleep sandstone) flowed oil at the rate of 2,500 B/D. By the end of 1949, 137 oil-producing wells and five dry holes had been drilled, and approximately 32 million bbl of oil had been produced. Approximately 6,000 acres may be considered productive of oil in the Tensleep Reservoir, and estimates of the oil that will be produced average 200 million bbl. The Tensleep Reservoir has further interest because it ha-greater closure than any oil field in the Rocky Mountain region; the closure of the Elk Basin anticline is variously estimated at 5.000 to 10,000 ft. of which the top 2.00 ft of the structure contained oil. SUBSURFACE OIL SAMPLING Fig. 1 is a structural map of the Elk Basin Tensleep Reservoir, on which the nine wells used in this study and the numbers correvponding to the well designations hereafter referred to are shown. Wells 1. 2, 3, 4, and 8 were tested and sampled during October and November. 1943. and Wells 5, 6. 7, and 9 during June and July, 1944. An electromagnetic type sampler developed by the Bureau of Mines and described by Grandone and Cook' was used in obtaining the subsurface oil samples. As the wells were tubed nearly to bottom, the sampler was run as far as possible in the tubing hut never below the top perforations. The following procedure was used in testing and sampling the wells: A well was shut in for at least three days, after

Jan 1, 1951

By Joseph Fry, Ralph H. Espach

In the spring of 1943, when it was evident that the Tensleep bandstone in the Elk Basin Field, Wyoming and Montana, held a large reserve of petroleum, Bureau of Mines engineers obtained samples of oil from the bottom of nine wells and analyzed them for such physical characteristics as the volumes. of gas in solution. saturation pressures or bubble points, shrinkage in volume caused by the release of gas from solution, expansion of the oil with decrease in pressure, and other related properties. The composition of the gas in solution in the oil was studied. The pressures and temperatures existing in the reservoir and the productivity characteristics of the oil wells were determined. The data obtained indicate that the oil in the Tensleep Reservoir of the Elk Basin Field has unusually varying physiral characteristics, such as a saturation pressure of 1,250 psia and 490 cu ft of gas in solultion in a barrel of oil at the crest of the structure and a saturation pressure of 530 psia and 134 cu ft of gas in solution in a barrel of oil low on the flanks. The hydrogen sulfide content of the gas in solution in the oil varies from 18 per cent for oil on the crest to 5 per cent for oil low on the flanks of the structure. Of even greater significance is the fact that these and other variable characteristics of the reservoir oil are related to the position of the oil in the structure. Many geologists and petroleum engineers have considered that all the oil in a petroleum reservoir has rather uniform physical characteristics and that equilibrium conditions prevailed in all underground accumulations of oil and gas; that such is not always so is borne out by the results of the study by the writers. INTRODUCTION The Rocky Mountain region is one in which may be found striking examples of the unusual in oil and gas accumulations, as is evident from the following: The high helium content (7.6 per cent) of the gas in the Ouray-Leadville limestone sequence in the Rattlesnake Field, New Mexico, and gases of similar helium content in other fields; 50" to 55' API gravity distillate in solution in carbon dioxide gas and recoverable through retrograde condensation, in the North McCallum Field, Colorado; the occurrence of gas, oil, or both in closely related structures contrary to the usual concepts of gravimetric segregation: the accumulation of gas and/or oil in structures closely related to other structures that apparently are more favorable but do not contain oil or gas accumulations; the high hydrogen sulfide content (as high as 42 per cent) of the gas associated with oil in some fields in the Big Horn Basin, Wyoming; and the wide range of fluid chararteristics found in the Elk Basin reservoir. Elk Basin, an interesting old oil field that has been producing oil from the Frontier formation since 1915, is situated in a highly eroded basin resulting from the erosion of the crest of an anticline and some of the underlying softer shales. The field came back into national prominence during 1943 when it became known that it was the largest single reserve of new oil discovered in the United States that year. The Tensleep sandstone was found to contain oil in November. 1942, when a well drilled to a depth of 4,538 ft (44 ft into the Tensleep sandstone) flowed oil at the rate of 2,500 B/D. By the end of 1949, 137 oil-producing wells and five dry holes had been drilled, and approximately 32 million bbl of oil had been produced. Approximately 6,000 acres may be considered productive of oil in the Tensleep Reservoir, and estimates of the oil that will be produced average 200 million bbl. The Tensleep Reservoir has further interest because it ha-greater closure than any oil field in the Rocky Mountain region; the closure of the Elk Basin anticline is variously estimated at 5.000 to 10,000 ft. of which the top 2.00 ft of the structure contained oil. SUBSURFACE OIL SAMPLING Fig. 1 is a structural map of the Elk Basin Tensleep Reservoir, on which the nine wells used in this study and the numbers correvponding to the well designations hereafter referred to are shown. Wells 1. 2, 3, 4, and 8 were tested and sampled during October and November. 1943. and Wells 5, 6. 7, and 9 during June and July, 1944. An electromagnetic type sampler developed by the Bureau of Mines and described by Grandone and Cook' was used in obtaining the subsurface oil samples. As the wells were tubed nearly to bottom, the sampler was run as far as possible in the tubing hut never below the top perforations. The following procedure was used in testing and sampling the wells: A well was shut in for at least three days, after

Jan 1, 1951

By Dix, E. H.

THE percentage of manganese used in commercial aluminum alloys is small, and yet this element is an important addition to some very valuable alloys. When used alone with commercial aluminum containing iron and silicon as impurities, the usual percentage in wrought materials is from 1 to 1.5 per cent., whereas castings may contain as much as 2 per cent. An aluminum-manganese alloy containing nominally 1.25 per cent. manganese is much used in sheet form for the manufacture of cooking utensils and other articles requiring a little greater strength and hardness than could be obtained with commercially pure aluminum. It is also used for various purposes in the form of rods, tubes and pipes. The aluminum-manganese alloys, both wrought 'and cast, offer excellent resistance to many kinds of corrosion attack. The U. S. Naval Gun Factory uses an aluminum alloy containing from 1 to 2 per cent. each of copper and manganese, for both castings and forgings. Manganese is also used, up to about 1 per cent., as a minor alloying .element in several of the strong aluminum alloys of the duralumin type. It is felt that the role of this element when thus used has not been fully understood, but it is believed that the results obtained in this investigation will throw additional light on the subject. The earlier work on the system aluminum-manganese was general in nature, and no detailed investigations of the relations existent in the useful aluminum-rich alloys have been reported. Guilletl1in 1902 surveyed the system, and Hendrichs2 in 1908 published an equilibrium diagram which, although based on .few data, is often used in the literature. Fragmentary work has also been done by other investigators."

Jan 1, 1927

By J. W. Edington

THE Hopkinson bar has become a popular technique for the measurement of the mechanical properties of materials deformed at high strain rate. Maximum use of the equipment is made in the arrangement first used by Kolskyl in which a short compression specimen is sandwiched between two pressure bars and is loaded by a single pulse travelling through the system. The pressure bars are used both to apply the load to the specimen and as transducers to obtain continuous strain-time histories of three pulses, incident on, reflected, and transmitted by the specimen. The data measured by the pressure bars can be analyzed in terms of the stress/strain behavior of the specimen.2'3 However, one of the assumptions of the analysis of the observed pulses is that the total stress and total strain do not vary significantly from point to point within the specimen at any given instant during the deformation process. Although this assumption is generally justified for very short disc-like specimens2 the situation is uncertain for larger specimens. For example, at small plastic strains (-0.01) Hauser et al.2 have some evidence of small flucations in the total stress within the crystal during deformation, even in relatively short aluminum specimens. In addition, Karnes4 has shown that the plastic strain, and by inference strain rate, is different at each end of a compression specimen tested in a Hopkinson bar, although the length of the specimen was not specified. Recently, the mechanical properties and the dislocation substructure have been investigated in single crystals of columbium5 (length 0.25 in., diam 0.19 in.), and copper6 (length 0.5 in., diam 0.5 in.) deformed at high strain rates. As part of this research program the assumption that the plastic strain is constant throughout the specimen has been checked by measuring the total dislocation density as a function of position in the specimen. Compression specimens of the same orientations and dimensions were tested as described previously5,6 sing a split Hopkinson bar. Since any discontinuity in strain distribution is most likely to arise during the initial stages of deformation the investigation was performed on specimens deformed to plastic shear strains of 0.054 (copper) at a strain rate 1.2 x l03 sec-1, and 0.06 (columbium) at a strain rate 1.5 X l03 sec-1. The orientation of the single crystals is shown in Figs. 1 and 3. Thin foils were taken parallel to the most highly stressed slip plane, i.e., (111) in copper and (011) in columbium, using conventional disc techniques. The dislocation densities were measured using first order reflections with compensation for invisible dislocations.5'6 In the copper single crystals the discs were randomly distributed throughout the cross section of the specimen. However, the dislocation density obtained from each disc was plotted vs the disc positions relative to the ends of the specimen. The results for the copper specimens are shown in Fig. 1. Clearly the dislocation density is constant throughout the main portion of specimen within the experimental error. The error bars on the dislocation densities correspond to a shear strain variation of 0.015 on the basis of previous measurements% ± of the rate of increase of dislocation density with strain in copper single crystals of the same geometry. Thus within this experimental error the plastic strain can be concluded to be constant within the specimen and the assumptions used in the analysis of the stress/time curves are therefore reasonably valid. The higher measured dslocation density near the impact end and the lower dislocation density at the bar end of the copper specimen is in agreement with the results of Karnes4 who showed that this strain/time curve rose to a maximum more rapidly at the impact end compared with the bar end. Hauser et al.2 have also pointed out that at small plastic strains (-0.01) the strain at the impact end of the specimen may be greater than that at the bar end. Thin foils taken from different points within the columbium single crystals demonstrated that the dislocation density could vary significantly within the specimen, see Fig. 2. Large areas of some thin foils up to 30 µ sq contained very few dislocations, see Fig. 2(a). However, in other parts of the compression specimen dislocation configurations like those shown in Fig. 2(b) existed over large areas (-30 µ sq). As a result, when the average dislocation density in a thin foil is plotted as a function of the position of the thin foil relative to the ends of the specimen, considerable scatter is observed, see Fig. 3. In this material then, the local dislocation density, and consequently the

Jan 1, 1970

By Frederick Laist, H. J. Maguire

The ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaccs, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper; this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it mas found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first- and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator produces a product that is self-fluxing; in fact, it is possible to produce a concentrate containing more iron than is necessary to flux the silica. Under these conditions, the amount of basic fluxing materials required for the smelting operations became very srnall and the converter slag lost its former value as a blast-furnace flux. For this reason, a less expensive method of recovering the copper, silver, and gold contained in it than smelting in blast furnaces had to be found. It was not feasible

Jan 1, 1921

By A. H. Larson, T. P. McNulty

RECENTLY, an investigation of the absorption of sulfur dioxide gas in molten binary copper alloys was conducted. A Sieverts-type apparatus, consisting of a mercury-filled gas dispensing buret and a mercury manometer, was used initially for determining the volume of gas absorbed as a function of pressure. The equilibration behavior of the alloys studied indicated that the mercury in the gas measuring system was absorbing sulfur dioxide. Owing to the widespread use of mercury as a displacement medium in absorption studies, an investigation was made to determine the nature and magnitude of the mercury - sulfur dioxide absorption effect. The gas measuring system was modified by substituting a Worden Quartz Products Type PDHV fused-quartz-spiral pressure gage for the mercury-filled dispenser and manometer. The dispensed gas volume at known temperature and atmospheric pressure was measured by evacuating a Pyrex vessel of known volume and by admitting sulfur dioxide into the vessel until the attached quartz pressure gage registered atmospheric pressure. Atmospheric pressure was measured concurrently with a separate mercury barometer. The volume of the empty sample chamber and its attendant apparatus was determined by measuring the equilibrium pressure accompanying the addition of a measured volume of sulfur dioxide into the initially evacuated system. The volume of the mercury sample was calculated from the density of mercury at the temperature of the study (25°C). Measured volumes of sulfur dioxide were then dispensed into the system and the equilibrium pressure accompanying each gas addition was determined. From the difference between the system volume and the mercury volume, the number of moles of gaseous sulfur dioxide remaining in the system at each pressure was calculated. The difference between the number of moles of gas dispensed into the system, denoted Enso2: and the number of moles of gas remaining in the system after absorption equilibrium had been attained, denoted nso2(g), was equal to the number of moles of absorbed gas, denoted nSO2. The number of moles of absorbed gas was then converted to absorbed volume, denoted VSo2, in cu cm at stp conditions of (PC and 760 mm Hg. Table I contains calculated values of Snso2, nSo2(g), and VSo2 for different sulfur dioxide pressures. In the original system, denoted Run I, volume limitations of the gas dispensing system prevented absorption studies at equilibrium pressures near atmospheric pressure, so a different gas dispensing system, denoted Run 11, was used for determining the last pressure reading in Table I. The data in Table I are expressed in terms of the absorption of sulfur dioxide in 49.68 cu cm of mercury. In Fig. 1, these data are expressed in terms of the absorption of sulfur dioxide in 100 cu cm of mercury. Since the absorption data plotted in Fig. 1 show a linear relationship, the volume of sulfur dioxide absorbed in mercury is a function of the first power of pressure. The absorption reaction is So2(gas) = SO2 (in Hg) The first-power pressure dependence, coupled with the fact that the sulfur dioxide could be removed from the mercury by applying vacuum, indicated reversible

Jan 1, 1967

By N. K. Chen, C. H. Mathewson

Recrystallization of aluminum single crystals after plastic extension is carefully studied in relation to the structure of the deformed matrix. The shapes of the new grains are analyzed with regard to slip planes and to the presence or absence of deformation bands. A mechanism by which the orientations of the grains are related to the parent lattice is described. EXPERIMENTS previously reported&apos; have been extended to develop some of the characteristics of the new crystals which are formed on annealing axially strained crystals whose deformational characteristics had been documented with special care. Thus, the presence of deformation bands affects the growth contours of the crystals, some of the strained crystals produced single crystals anew, and some, polycrystals, on annealing, while others merely "recovered" or "polygonalized" after the 600°C annealing treatment generally adopted in these tests. In the matter of orientational relationships between new crystals and the strained matrix, the present experiments have added little to previous experience, which had demonstrated great variety in the range of orientations encountered and no simple theory or correlation. For example, there has been ample evidence for the predominance in various face-centered cubic metals of a favored orientational relationship; viz., a rotation of 30° to 40° around a <1ll> axis, between grains growing in a matrix with a strong single orientation texture and the matrix itself.&apos;-&apos; This reorientation has been interpreted by various investigators in support of both the "oriented nucleation" and the "oriented growth" hypothesis. In the case of axially extended single crystals of aluminum, no general relationship, such as the one stated above, can be used to correlate the orientations of the recrystallized grains with that of the original crystal. Thus, Carpenter and Elama and Burgers and Basart7 were content to assume that the orientational relationships so developed were random in nature. Mathewson, however, in the Campbell Lecture of 1943 "rgued on the basis of <112> slip that a complex strain, chiefly characterized by rotation around a variable axis in the slip plane combined with a principal rotation around the pole of the slip plane, could be responsible for such devious relationships. Nevertheless, owing to the limited data now available dealing with orientational relationships between new grains and the single crystals strained in tension from which they have recrystallized, no adequate examination of the above generalization could be made. Here, there is the disturbing preliminary condition that any desired orientational relationship may be expressed by means of two rotations about mutually perpendicular axes, so the process lacks a certain critical flavor and any successful choice of axes meeting certain theoretical requirements could be replaced by another differently selected pair. With this reservation clearly in mind the process of double rotations, as previously indicated, was used to relate the orientations of the single crystals which grew out of the strained single crystalline matrix and was construed as certain evidence in favor of the theory of incongruent shearing action proposed by Mathewsons as a necessary element in the (111) slip process with close-packed metals. There is here

Jan 1, 1953

By C. E. Reistle

All crude oils become more viscous when chilled, but the only oils that congeal and precipitate paraffin to such an extent as actually to cause production troubles are those that contain an appreciable amount of wax. In handling these oils of high wax content, three distinct problems may be encountered before the oil reaches the refinery. The first problem is the precipitation and accumulation of paraffin in the well, either in the oil string or on the face and in the pores of the sand. The second problem is the accumulation of paraffin and the congealing of oil in the transportation lines. The third problem is the precipitation of paraffin and the formation of tank bottoms. Factors That Control the Solubility of Paraffin in Crude Oil Two main factors, possibly three, govern the solubility of wax in crude oil. The first of these is temperature. The solubility of wax in crude oil increases with an increase in temperature, and as the temperature approaches the melting point, the wax becomes soluble in all proportions in the crude oil. The higher the melting point of a wax, the less soluble it is in crude oil below its melting point. All crude oils containing wax can be chilled to a point where the oil is saturated with wax. If the temperature is decreased below this point, some of the wax will crystallize from solution. Fig. 1 shows the effect of temperature on the solubility of crude paraffin in oil. The second factor is the amount of volatile constituents and gas removed from the crude oil. Evaporation of the volatile constituents and gas lessens the volume of the oil and concentrates the solution of wax in the oil; therefore less wax can be held in solution at a definite temperature. As the natural amount of wax present in the oil is constant, this results in the oil becoming saturated with wax at a higher temperature than if the volatile constituents and gas were still in the oil. As an example of this, a fresh sample of crude oil having a gravity of 39.8

Jan 1, 1928

By AIME AIME

INSTITUTE members attending the Annual Meeting in New York who want to see one of the mining engineers&apos; newest aids, photoelastic stress analysis, are due for an interesting afternoon on Thursday, Feb. 15, when open house: will be held at the Columbia University mining laboratory. Information as to the direction and distribution off stresses in mine structures, which has been developed by Professor Bucky, associate professor at the Columbia School of Mines, and David Sinclair, research assistant, is useful in the design of pillars and in the placing of openings relative to working places such as gangways and haulage levels.: This work has been sponsored during the last ten years by the Engineering Foundation.. It is fully reported in T. P. No. 1140.

Jan 1, 1940