Search Documents

By C. Atkinson

A method is described for the numerical solution of the diffusion equation with a composition-dependent diffusion coefficient and applied to the radial growth of a cylinder; the radial growth of a sphere, and the symmetric growth of an ellipsoid. Sample applications of the method are made to the growth of particles of proeutectoid ferrite into austenite. RECENTLY&apos; we described a method for numerical solution of the diffusion equation with a composition-dependent diffusion coefficient for the case of the growth of a planar interface. In this paper we extend this method to describe the radial growth of a cylinder, the radial growth of a sphere, and the symmetric growth of an ellipsoid. In the latter case, limiting values of the axial ratios of the ellipsoid reduces the problem to one of a cylinder, a sphere, or a plane depending on the axial ratio. A check on these limiting values is made in the results section. In all of these cases we consider growth from zero size. A natural consequence of this assumption as applied to the sphere, for example, is that the radius of the sphere is proportional to the square root of the time. This is consistent with the condition that the radius is zero initially, i.e., grows from zero size. It may be argued that it is more realistic to consider particles which grow from a nucleus of finite initial size; even in this case the analysis of this paper is likely to be applicable. This can be seen if a comparison is made of the work of Cable and Evans,2 who consider a sphere of initially finite size growing by diffusion in a matrix with a constant diffusion coefficient, with the results of Scriven3 for growth from zero size. This comparison shows that the rates of growth in each case differ trivially by the time the particle has grown to about five times its initial size." This investigation is a generalization of those of Zener,4 Ham,5 and Horvay and cahn6 to the situation often encountered experimentally, in which the diffusion coefficient varies with concentration. First let us consider each of the cases separately. I) GROWTH OF SPHERICAL PARTICLES FROM ZERO SIZE In this case the differential equation in the matrix depends only on R, the radius in spherical coordinates, and can be written: ? 1 <^\ ^13D . , dt U\dRz + R 3Rj + dR dR [ J where C is the composition, t is the time, and D is the diffusion coefficient which depends on c. The boundary conditions will be: c = c, at the moving interface in the matrix, c = c, at infinity in the matrix (and at t = 0, everywhere in the matrix), c = X, is the composition in the spherical particle. Each of the above compositions is assumed constant. In addition there is the flu condition at the moving interface which can be written: , dR0 ~/3c dt \dR/H =Ra where R,, which is a function of t, is the position of the moving interface. We make the substitution q = RI~ in [I] reducing this equation to: & - m - *ws) »i where we have written D = D,F(c) or simply D,F, and Do = D(c,). Thus F[c(q0)] = 1 where q, = ~,/a is the value of the dimensionless parameter q evaluated at the interface. Multiplying Eq. [2] by dq/dc and integrating, we find: where the lower limit of the integral has been chosen so that dc/dq — 0 as c — c,, thereby satisfying the boundary condition at infinity. We require, then, to solve Eq. [3] subject to the condition c = c, when q = q, (this follows from putting R = R, at the interface) together with the flux condition which can be rewritten in terms of q as: Eqs. [3] and [4] together with the condition c = c, at q = q0 enable us to find 77, and the concentration profile c = c(q). Numerical Method. We treat Eq. [3] in the same way as we did the corresponding equation for the planar interface problem&apos; i.e., by dividing the interval c, to c, into n equal steps so that: cr = ca -rbc [5] where r takes the values 0, 1, ... n and we call no,, q1, ... nn the values of n corresponding to the compositions c,, c,, ... c,.

Jan 1, 1970

By P. Douglas, G. M. Leak, B. Mills

The sinusoidal surface relaxation technique has been used to measure the surface self-diffusion coefficient of spectroscopically pure nickel over a wide temperature range under a hydrogen atmosphere. A kink in the Arrhenius plot has been observed. In the temperature range T/T 0.98 to 0.80 (T in O K and T, is the melting temperature) the average self diffusion coefficient is given by Below the temperature T/T,- 0.80a decrease in the slope of the log Ds us 1/T plot is observed. This is associated with a diffusion process characterized by a lower activation energy (-20,000 cal mole&apos;&apos;) and smaller preexponential term (-10- sq cm sec"). A series of experiments were carried out at T/Tm = 0.61 under a hydrogen atmosphere of higher oxygen partial pressure than for the rest of the experiments. It was found that Ds was significantly depressed due to oxygen adsorption. This evidence supports the opinion that the low temperature process (activation energy -20,000 cal mole-&apos;) is unlikely to be due to oxygen adsorption. An interesting feature of the present data is that the transition temperature (T/Tm - 0.80) is a function of orientation. For a small number of crystals of measured orientation the transition temperature was observed to be higher towards the low index (100) pole. Theories of surface diffusion are briefly reviewed and it is concluded that the present reszuts are best explained by invoking a surface roughening process. GJOSTEIN has recently analyzed available surface diffusion data for a wide range of metals. He suggested that two mechanisms were operative for fcc metals, an adatom process at high temperatures and a vacancy process at low temperatures. Results for nickel can be summarized as follows. At low temperatures (T/T, - 0.3 to 0.44) under ultra high vacuum conditions, Melmed2 measured an activation energy Q of 21 kcal mole-&apos; using field electron emission microscopy. At higher temperatures (T/T - 0.7 to 0.9) under a vacuum of 10- &apos; torr, Maiya and lakel measured y as 39 kcal mole-&apos; using the multiple scratch smoothing technique. The present work was undertaken to try to find out if two distinct processes could be observed. High temperature results give Q about 47 kcal mole-&apos;: there is evidence also for a low temperature value of about 20 kcal mole-&apos;. These measurements were all made under a hydrogen atmosphere, in the temperature range 860" to 1412°C. Concurrent with the present study Bonze1 and jostein> have also observed a break in the Arrhenius plot for the (110) surface of nickel. These measure- ments under ultrahigh vacuum conditions using the laser diffraction technique are in excellent agreement with the work reported here under hydrogen annealing conditions. THEORY The available surface relaxation techniques include single and multiple scratch smoothing and grain boundary grooving. The processes have been compared in detail by Gjostein for conditions where surface diffusion dominates6 and Mills et al? where volume diffusion dominates. In summary the relevant points are as follows. Grain boundary grooving gives an average Ds for the two surfaces adjacent to the boundary and this can, to some extent, be simplified by using symmetrical bicrystals. This technique has been used to study the effect of environment on Ds for silver and copper.&apos;-&apos;&apos; Scratch techniques yield Ds values for the small orientation range exposed by the scratches (-2 deg). The multiple scratch process is preferable because the profile rapidly becomes sinusoidal and can then be interpreted theoretically in a relatively simple way. Also corrections for mass transport processes other than surface diffusion can be introduced easily. Mullins" considered a sinusoidal profile described the wavelength of the profile. After time t the profile can be described by the equation The terms A, A&apos;, C, and B which account, respectively, for contributions due to evaporation-condensation, diffusion through the gas phase, volume diffusion through the lattice, and surface diffusion are defined as: where Ds = the surface self diffusion coefficient ys = the surface energy per unit area p = the equilibrium vapor pressure over a flat surface pa = the equilibrium vapor density over a flat surface DG= the diffusion coefficient of vapor molecules in the inert gas DM = the mass transfer diffusion coefficient which for a pure cubic metal is Dv/f where Dv is the radiotracer diffusion coefficient and f is the correlation factor H = the molecular volume V = the surface density of atoms, il2&apos;3 M = mass of an evaporating molecule

Jan 1, 1970

By J. B. Newkirk, A. H. Geisler

The alloy Cu4Pd has a disordered face-centered-cubic structure when quenched from temperatures between 478ºC and the melting point (about 1100°C). Below 478ºC an ordered phase is stable. The results of a Debye-Scherrer X-ray analysis indicate that the ordered phase has a tetragonal unit cell described by the space group C24h — P42/mt with 2 Cu in 2a, 2 Cu in 2f, 4 Cu in 4j (x = 0.2, y = 0.6), 4Pd in 4j (x = 0.4, y = 0.2), and 8 Cu in 8k (x = 0.1, y = 0.3). The orientation relationship between the face-centered-cubic phase and the ordered tetragonal phase is given by: [100],,. // [130]al,. COO1Ia.d.//COO1I,,.. • The behavior of Cu,Pd is typical of ordering alloys except that the transformation is very sluggish. The increase in hardness and the microstructural and X-ray diffraction effects are interpreted in terms of coherency strains caused by the ordering. AN anomalous construction in the Cu-Pd phase diagram (Fig. 1) was reported in 1939 and has been allowed to stand without further published attention since that time. The odd figuration about the composition 10 to 27 atomic pct Pd is derived mostly from the work of Jones and Sykes.1 Evidently several features of this binary system require further study if the constitutional forms are to be well understood. The present paper includes a study of one of these features, that is, the crystal structure of a single ordered alloy containing nominally 20 atomic pct Pd. This choice of composition was suggested by the work of Harker and associates who determined the structure of Ni4Mo2 and Ni4W.3 The nature of the ordering process in Cu4Pd was studied also by observing the hardness, microstructure, and Debye-Scherrer patterns of specimens which had been aged at various temperatures after quenching from an initial disordering treatment. Experimental Methods A 20 gram ingot of Cu4Pd was made by melting spectrographically standardized copper from Johnson, Matthey, and Co., and commercially pure (99.5 + ) palladium in an argon-filled quartz tube. Chemical analysis showed that the ingot contained 80.0 atomic pct Cu. The ingot was rolled about 60 pct to a strip 0.060 in. thick and was homogenized for 16 hr at 950°C in low pressure argon. Rods cut from the rolled strip were worked into wire 0.015 in. in diameter, and specimens for hardness and microscopic examination were cut from the remaining strip. All specimens, with the exception of some of the wire, were given an initial disordering treatment by heating for 16 hr at 950°C, followed by water quenching. A 10 cm length of as-drawn wire was water quenched after being held in a temperature-gradient furnace4 for 89 days. Room-temperature Debye-Scherrer photograms were then made at points along the wire to determine the temperature below which the ordered phase was stable. Although the accuracy of temperature determination in the gradient was only about ±10 °C, the temperature gradient was sufficiently gradual that the sensitivity was much better and locations which had differed by as little as 1°C could be distinguished. An analysis of the crystal structure of the well ordered alloy was made by X-ray diffraction using a specimen cut from this wire. The change of Debye-Scherrer pattern as ordering progressed was studied by using isothermally aged samples of initially disordered wires. The wires were sealed under low-pressure argon in small quartz tubes for heat treatment. After the aging treatment, the tubes were quenched in water and photograms were made at room temperature in a 10 cm diam camera using filtered Cu kX. (A = 1.540511) Hardness was measured on a Vickers hardness tester using a 10 kg load and 2/3 in. objective lens. Reported values are the average of at least three impressions made on flat specimens 0.060 in. thick. After the hardness of a heat-treated sample had been measured, it was resealed in low-pressure argon and returned to the furnace for continued aging at the same temperature. In this way, two samples served for all aging times at each temperature. Hardness specimens which had been aged 500 hr or more were used for metallographic examination after the final aging treatment. A dilute potassium-dichromate etching solution was used.

Jan 1, 1955

By S. T. Wlodek

The surface and subscale oxidation reactions were followed by means of continuous weight-gain and metallographic techniques over the range 1600" to 2200°F (871° to 1204 °C) for up to 400 hr. Full identification of all scale and subscale reaction products was obtained by electron and X-ray diffraction. At or below 1800°F (982°C) a linear rate of reaction (QL = 46.0 kcal per mole) governed the oxidation process, extending for up to 100 hr at 1600°F (871 "C). During linear oxidation the surface scale consisted of an amorphous SiO2 film overgrown with Cr 2O 3 and NiCr204. This initial linear process was followed, and above 1800°F completely replaced, by two successive parabolic rate laws (Qp = 60 and 57 kcal per mole). This parabolic reaction involved the formation of a complex scale consisting of Cr2 O3 and smaller amounts of NiCr2O4. Parabolic oxidation appeared to coincide with the disruplion of the silica film present during linear oxidation and was followed by subscale (internal) oxidation of crystobalite and NiCr2O4. The balance between the subscale and surface oxidation reactions controls the oxidation of this commercial alloy. The amorphous silica film appears to result in the linear rate and diffusion through Cr2O3 is the more likely rate-limiting step during parabolic oxidation. THE oxidation of a multicomponent composition is a complex phenomenon not presently amenable to a rigorous classical interpretation. Nevertheless, even a qualitative understanding of the scaling and subscale reactions that occur in a commercial composition can illuminate the reactions that limit its high-temperature stability in an oxidizing environment. This study of the oxidation of Hastelloy Alloy X presents the first of a series of studies with the above approach in mind. Hastelloy X exhibits one of the best combinations of strength and oxidation resistance available in a wrought, solution-strengthened, nickel-base alloy. Although during long time exposure some precipitation of M6C and M23C8 carbides as well as a complex Laves phase occurs, the amounts are probably small enough to have no appreciable effect on the chemistry of the matrix. Radavich has identified the oxidation products on Hastelloy X oxidized for 5 min to 10 hr at 1115°F as NiO and the NiCr2O4 spinel. Oxidation for 5 to 15 min at 1500°F produced a scale of spinel, NiO, and a rhombohedra1 phase, probably Cr2Os. Sannier et 2. have reported continuous weight-gain data for Hastelloy X at 1650" and 2010°F and internal-oxidation measurements after 150 hr at 2010°F. In addition, much of the data on binary Ni-Cr alloys recently reviewed by Kubaschewski and okins&apos; and Ignatov and Shamgunova4 as well as studies of binary Ni-Mo alloys5 are also pertinent to the oxidation of this composition. EXPERIMENTAL Continuous weight-gain measurements and metallographic measurements of subscale reactions were the main experimental techniques used in this study. X-ray and electron diffraction backed up by a limited amount of electron-microprobe analysis served to characterize the nature of the scale- and subscale-reaction products. Two heats of commercial sheet of the composition given in Table I and identified as A and B were used in the bulk of this study. Internal-oxidation measurements were made on a third heat of material in the form of a 0.5-in.-diam bar. In order to assure homogeneity, all heats were reannealed 4 hr at 2175°F prior to sample preparation. weight-Gain Measurement. All specimens (1.5 by 0.4 by 0.03 in.) were abraded through 600 paper, electropolished, and lightly etched in an alcohol-10 pct HCl solution. An electrolyte of 150 cu cm H,O, 500 cu cm HsPO4 (85 pct conc), and 3 g CrO3 at a current density of 0.9 amp per sq cm or a solution of 10 pct HaW4 in alcohol used at 4 v and 0.3 amp per sq cm was used for electropolishing. The resultant surface exhibited a finish of 3 ± 1 p rms. Continuous weight-gain tests were made at 1600°, 1700°, 1800°, 1900°, 2000", and 2200°F on auer&apos; type balances capable of recording a total weight change of 110 mg with an accuracy of k0.1 mg. All tests were made in air dried to a dew point of -70°F and metered into the 2-in.-diam reaction

Jan 1, 1964

By P. L. Allsman

Butte mining district contains extensive manganese vein deposits forming a peripheral zone. Oxidation in the veins studied usually extends to a depth of about 75 ft. Secondary minerals formed by oxidation were found to be ramsdellite—always accompanied by intermixed pyrolusite—and cryptomelane. Enrichment of the gossan is accomplished by reduction of weight upon oxidation; theoretical enrichment is 32.2 pct. Additional enrichment is caused by leaching of soluble minerals, particularly calcium and magnesium carbonates. BUTTE mining district contains extensive manganese vein deposits in the outer zone, surrounding the copper and zinc deposits and corresponding to the well known silver zone. This article describes the mineralogy of the manganese veins, the oxidation and enrichment processes, and the use of this information in prospecting. Information was derived from a study of the Emma, Star West, Tzarena, and Norwich mines, selected as representative of the district. Vein exposures at these mines were mapped, studied, and sampled on the outcrops and throughout the oxidized zone. Specimens were cut and polished for minera-graphic examination, identification, and textural studies. Knowledge of the manganese oxide minerals is scanty, previous information having been rendered obsolete by publication of the first correctly identified list of manganese oxide minerals by Fleischer and Richmond in 1943. Positive identification of the manganese oxides is possible only by X-ray analysis. Identifications for this study were made by the author with a Phillip&apos;s Diffractometer at the Montana School of Mines and confirmed by Lester Zeihen of The Anaconda Co., using a Norelco X-ray camera. It was necessiary to re-evaluate some X-ray data, as published patterns of several manganese oxides proved to be of mixtures, mostly showing pyrolusite as a contaminant. Perhaps the most useful information on oxidation and enrichment of manganese is presented in recent books by Goldschmidt1 and Rankama and Sahama.2 While their hypotheses are not conclusively proved, all laboratory and field evidence has served to substantiate them. This information was very useful in this study. Mineralogy: The primary minerals of the manganese veins are chiefly rhodochrosite and quartz. Rhodonite is abundant in the northern part of the district and in places has been found to comprise over a third of the vein matter. A variable but generally small amount of sulfides may be present, principally pyrite and silver minerals. Sphalerite is progressively more abundant near the zinc zone. Rhodochrosite is believed to form complete iso-morphous series with siderite, ankerite, and calcite. Some variation into these compositions is common, and the intermediate forms are termed manganosid-erite, manganankerite, and rnanganocalcite. Much of the rhodochrosite is remarkably pure. Other manganese minerals in the district include huebner-ite, alabandite, and helvite. Ramsdellite (MnO2, orthorhnmbic) is the principal manganese oxide mineral, comprising perhaps two-thirds of the total oxides. It is dull to iron black, and generally massive or platy in structure. A prominent platy cleavage is the only distinguishing megascopic characteristic. Pyrolusite (MnO2, tetragonal) is next most abundant to ramsdellite, with which it is usually intimately mixed. The luster is often brighter or more metallic than in ramsdellite, and needle-like crystals are diagnostic. Pyrolusite is common in small cavities formed by oxidation of pyrite grains. It is relatively abundant in zones of high limonite content. Cryptomelane (KMnO16 tetragonal ?) is rare in the outcrop, but becomes more abundant with depth. At depths of several hundred feet it is the principal oxide. Although its appearance varies, a blue-black flinty luster and blocky to conchoidal fracture are most common. A potassium flame test will identify this mineral. Hardness of all three oxides varies from 2 to 6. The three are quite commonly intermixed, and their textures can vary greatly. The commonest textures are massive or colloform, representative of colloidal deposition, or vuggy and boxwork textures, formed by partial leaching and oxidation in place. A box-work of either ramsdellite or chalcedony is formed after rhodochrosite rhombs and is indicative of ore shoots in this district. Some replacement of both quartz and the granitic wallrock by ramsdellite has been noted, but most of the oxide was deposited as a fissure filling by fine particles. No trace of manganite, hausmannite, braunite, or manganosite was found. No minerals of the psilome-lane group were detected besides cryptomelane. Amorphous MnO, was found at several spots. A specimen of oxide coated with yellow barite crystals was amorphous and not psilomelane (BaMn9O18. 2H2O). Voids formed by the leaching of sphalerite were coated with cryptomelane, not hetaerolite (ZnMn2O4) as might be expected. No manganese sulfate minerals were found in the gossans; however manganese alum (apjohnite ?) has been re-

Jan 1, 1957

By E. W. Stewart, G. P. Conard, J. F. Libsch

The effects of several additives upon the reduction characteristics of hydrogen-reduced ferrous formate are described. The various additives inhibit sintering of the reduced iron particles by apparently different mechanisms. The magnetic properties of the low density compacts produced from the resulting ultra-fine iron powders were improved markedly. THE permanent magnetic characteristics of ultra-fine iron powder prepared by various means have been a subject of considerable interest and experimentation in the past few years. When such particles are small enough to show single domain behavior, they possess&apos; 1—permanent saturation magnetization, and 2—high coercive force. In the absence of domain boundaries, the only magnetization changes in a particle occur through spin rotation which is opposed by relatively large anisotropy forces. With decreasing particle size, the coercive force tends to increase to a maximum and then decrease because of the instability in magnetization associated with thermal fluctuations. Kittel&apos; has calculated the critical diameter at which a spherical particle of iron can no longer sustain domain boundaries or walls to be approximately 1.5x10-&apos; cm. Stoner and Wohlfarthr in England and Neel4,6 in France have shown from purely theoretical calculations that the high coercive force expected from single domain particles is dependent upon crystal anisotropy, shape anisotropy, or strain anisotropy contributions. Further work by Weil, Bertaut,&apos; and many others has contributed much to the understanding of fine particle theory. Neel and Meikeljohn" have demonstrated that a decrease in particle size below a critical value of approximately 160A leads to a quite rapid decrease in coercive force because of the prevention of stable magnetization by thermal agitation. Lih1, working with powders prepared by the reduction of formate and oxalate salts of iron, has shown the marked influence of powder purity upon magnetic properties. Maximum coercive force was obtained in powders of approximately 65 pct metallic iron content while the maximum energy product, (BxH) occurred in powders of 85 pct metallic iron content. Careful consideration of the preceding theoretical considerations and experimental results has led to the manufacture of permanent magnets from ultra-fine ferromagnetic powders by powder metallurgy techniques. Such work has been done by Dean and Davis," the Ugine Co. of France, and Kopelman." The aforementioned work of Kopelman and the Ugine Co. was concerned somewhat with the effect of various additives upon the properties of hydrogen-reduced ferrous formate. Virtually no work, however, has been published on the effects of additives on the reduction rates of metal formates, although unpublished work by Ananthanarayanan16 howed promise of improved energy product in ultra-fine iron compacts prepared by the hydrogen reduction of a coprecipitated mixture of magnesium and ferrous formate. After consideration of the preceding information, it was hoped that a better balance between the metallic iron content and particle size of the reduced iron powder could be accomplished by a prevention of the attendant sintering of the partially reduced iron powder during the reduction reaction. It appeared possible that magnesium oxide might interpose a mechanical barrier between adjacent iron particles and prevent their sintering together, while metallic cadmium and metallic tin would interpose a liquid barrier which might accomplish the same purpose. The degree to which these materials were effective in accomplishing the foregoing objective and the experimental details associated with the work are reported in the following sections of this paper. Experimental Procedure Preparation of Formate and Oxide Mixtures: To obtain ferrous formate of reproducible reduction characteristics, a slight modification&apos; was made in the technique of Fraioli and Rhoda." A supersaturated solution of ferrous formate was mixed with an equal volume of 95 pct ethyl alcohol and the formate crystals precipitated by stirring and screened to —325 mesh. These crystals were in the shape of elongated hexagons, approximately 4x10 micron in dimension. Various preparations of such ferrous formate, designated as lot 111, were reduced for 2 hr, yielding ultra-fine iron particles of exceedingly reproducible size, metallic iron content, and magnetic properties. The magnesium and cadmium formates were prepared by the reaction of dilute formic acid with their respective carbonates, while the tin formate was prepared by the reaction of dilute formic acid with stannous hydroxide. To evaluate the effect of metallic formate additives in intimate mixture with the ferrous formate, varying amounts of magnesium, cadmium, and tin formates were coprecipitated with the latter. The designations of these materials and their chemical compositions are given in Table I. Due to the differing solubilities of the various formates in aqueous media,

Jan 1, 1956

By W. H. Smith

IN connection with some recent work on the effect of impurities on the ductility of chromium, it appeared desirable to know the solid solubility of carbon in chromium. A literature survey indicated that this information was not available. Although considerable work has been done on the Cr-C phase diagram,&apos;.&apos; previous investigators have been more concerned with the structure and phase boundaries of the carbide phases than with the terminal solid solution. The phase diagram shown in Fig. 1 is taken from the work of Bloom and Grant&apos; and represents the most recent determination. As indicated by the dashed line, the a solid-solubility limit was not determined. Experimental Procedure Alloys of chromium were prepared from hydrogen-treated and vacuum-degassed electrolytic chromium plus spectrographic grade carbon. The oxygen and nitrogen content of the alloys was <0.002 pct. After melting, analysis of the alloys showed them to contain 0.02, 0.08, 0.15, and 0.55 pct C. Pieces of the alloys were heated in a protective atmosphere to various temperatures and then quenched after holding for a time sufficient to insure equilibrium. Microscopic examination of the as-quenched alloys for the presence of a second phase was used as a measure of the solubility limit. The heats were made in a multiple hearth arc-furnace using a zirconium-gettered static argon atmosphere. A zirconium melt was made before each Cr-C heat. Triple melting was used to insure ingot homogeneity as shown by microscopic examination. The alloys were prepared by adding portions of a 4.5 pct C-Cr master alloy to high purity chromium. The carbon contents listed previously were those obtained by analysis. The nitrogen and oxygen contents after arc melting were both <0.002 pct. Sections 1/8X1/4X1/2 in. were cut from the 100-g ingots and a hole drilled in one end in order to suspend the sample from a molybdenum wire. After the surface was carefully cleaned, a sample of each melt was hung in a mullite tube heated externally by a platinum resistance furnace connected to a vacuum system. The lower portion of the mullite tube was sealed to Pyrex and closed off several inches below the furnace. This was filled with sili-cone oil kept cold by circulating cold water around the outside of the Pyrex. Quenching into the oil bath was achieved by melting a fuse wire supporting the sample. It required about 4 sec for the sample to cool from 1400" to 600°C. This severity of quench was considered satisfactory to freeze-in the high temperature equilibrium. For tests made at temperatures of 900" to 1200°C, heating was done in vacuum; for tests above 1200°C, an argon atmosphere was used. The holding time employed ranged from 12 hr at 900°C to 6 hr at 1400°C. Experiments were performed at temperatures of 900°, 1000°, 1100°, 1200°, 1300°, and 1400°C. Microscopic examination for evidence of a second phase was done at X1500. Experimental Result The microstructures of a 0.08 pct C-Cr alloy as-cast and after quenching from 1300°C are shown in Figs. 2 and 3. A 0.15 pct C-Cr alloy quenched from 1300°C is shown in Fig. 4. The data obtained from the quenching experiments is shown graphically in Fig. 5. If the Van&apos;t Hoff equation is obeyed, a plot on a logarithmic scale of the mol fraction of solute vs the reciprocal of the absolute temperature should give a straight line. For dilute solutions the weight percentage can be substituted for the mol fraction without introducing any appreciable error. The Van&apos;t Hoff equation can then be written as where H is the heat of solution in calories per mol. The slope of the straight line on the log pct C vs 1/T plot gives the value of AH. Assuming that the Van&apos;t Hoff equation is obeyed, which is probably justified for the dilute solution of carbon in chromium, the heavy straight line shown on Fig. 5 represents the best fit of the data. This line was obtained as follows. On Fig. 5 the results of the microscopic examination of all alloys following quenching were plotted and designated as to whether one or two phases were seen. Below 1100°C all alloys showed a second phase on quenching. The heavy vertical lines shown in Fig. 5 therefore represent the possible range of the ter-

Jan 1, 1958

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

H. Schwartzbart and W. F. Brown, Jr.—The authors have divided the effects of recovery on the true stress-true strain curve into two types; metarecovery, which effects only the first part of the curve or the yield strength, and orthorecovery, which effects the flow stress at any strain. Both of these are said to be true recovery effects, involve no recrystallization, and are explained by the removal of two different types of imperfections caused by work hardening. However, there seems to be some question as to whether the data are sufficiently conclusive to exclude, as an explanation of the authors&apos; results, a mechanism based on the relief of residual stresses between the grains or slip bands and recrystallization. It appears that metarecovery could be interpreted in the same fashion as a customary interpretation of the Bausch-inger effect. The balanced system of internal stresses which exists between grains in a strained specimen due to varying orientation and, hence, yield strengths, of the different grains is responsible for a reduced yield strength in compression following pre-tension, and, similarly, for an elevated yield strength in tension following pre-tension. If the specimen is now heated so that the internal stresses are relieved by creep, then the yield strength in tension following tension will have been reduced and in compression following tension will have been raised. There seems to be a very strong case for the lack of recrystallization in the aluminum investigated by the authors, if one defines recrystallization as the presence of visually detectable new grains or accepts the X-ray evidence as conclusive. One must remember, however, that the appearance of spots on the back-reflection X-ray patterns cannot be taken as the time when recrystallization first started. The areas of recrystallized strain-free material must first have grown to a size large enough to give distinct spots on the patterns and this may take some time. Averbachl7 in an investigation of brass has shown that recrystallization can be detected by extinction measurements at temperatures lower than those based on hardness or X-ray line width determinations. It can be seen from fig. 10 that the rate of recrystallization is extremely low over a considerable time period at the onset of the process. Observations on the rate at which small amounts of recrystallization effect the flow stress would have given further insight as to whether undetectably small amounts of recrystallization might have been responsible for orthorecovery. Also, the question arises as to whether the effects observed in fig. 6 for various times and temperatures could not have been obtained if the time at 212°F were sufficiently long. In addition, the argument that the curve in fig. 10 is not sigmoidal seems weak in view of the scattering of the points. It is conceivable that an accurate determination of the curve for the first 100 hr would exhibit a relationship other than the one drawn. There is one point we would like to raise about the condition of the starting material. The authors annealed their material at 750°F for 15 min to remove the effects of any previous work hardening or machining strains. Reference to the work by Anderson and Mehl shows that this treatment may not have completely recrystallized the aluminum, so that the starting material may have had some strained areas. Higher temperatures or longer times may have been required to remove the effects of any small strains. We would like to mention some results of tests being conducted at the Lewis laboratory of the National Advisory Committee for Aeronautics in an investigation of the Bauschinger effect in relation to fatigue. Tests were performed on annealed electrolytic copper and several annealed brasses. Specimens were pre-strained 1 pct in tension and then tested in compression or tension with and without intermediate stress-relieving annealing treatments at 500°F for various times. Specimens heated at 500°F for 10 1/2 hr showed an elevation of the flow curve in compression and an approximately equal lowering of the flow curve in tension when compared with the curves for the un-heat treated specimens. After approximately 0.8 pct strain, all flow stresses coincided and were equal to the flow stress of the virgin material at this strain. This behavior is consistent with the metarecovery observed for aluminum by the authors and for which a residual stress model can be used. On the other hand, increas-

Jan 1, 1951

By Luc Delaey, Horace Pops

The structure and morphology of thermoelastic and burst type martensitic phases that form upon cooling in Cu-Zn-Si p phase alloys have been studied by transmission electron microscopy. The martensitic phases are composed of a lamellar mixture of two close-packed structures with different stacking sequence, namely ABCBCACAB (orthorhombic) and ABC (fcc). Striations within thermoelastic martensite are most likely produced during interaction with impinging burst-type martensite and not as a consequence of secondary shears. In a study of the martensitic transformation in ternary Cu-Zn based 0 phase alloys1 the dependence of the martensitic transformation temperature, M,, with composition shows variations for elements within a constant valence subgroup and between different subgroups. Such variations are not reflected in a change in habit plane, which is approximately the same for each ternary alloy, namely in the vicinity of (2, 11, 12 Ip. The fact that the habit plane remained constant, despite large differences in M, temperature and electron concentration, suggested2 that the crystal structures of the martensitic phases could be nearly the same. Crystal structures of ternary Cu-Zn based martensites have been determined recently for alloys containing the three-valent elements gallium3, 4 and aluminm. The present studies have been made to examine the structures and morphology of the martensitic phase in ternary Cu-Zn based alloys containing a four-valent element, silicon. I) PROCEDURE Two alloys were prepared by melting and casting weighed quantities of the component high-purity metals in sealed quartz tubes under half an atmosphere of argon. They were subsequently remelted by levitation under a protective atmosphere of argon. After allowing for losses of zinc as determined by the difference in weight before and after casting, the compositions in atomic percent of both alloys were established to be Cu-33.5 Zn-1.8 Si and Cu-27 Zn-5.0 Si. These alloys were homogenized in the P-phase field for 2 days at 800" C. Bulk samples consisted of a martensite phase at room temperature, the M, temperature being approximately 30&apos; and 200" for the 1.8 and the 5 pct Si alloys, respectively. Thin disks were cut from the ingots using a spark machine, and they were heated for 5 min at 800&apos; and quenched into water in order to obtain martensite. These slices were thinned chemically at room temperature in a solution consisting of 40 parts HN03, 50 part H3PO4, and 10 parts HC1 and thinned further electrolytically by the Window technique, using a voltage of 15 to 25 v and a mixture of 1 part HN03 and 2 parts methanol, which was kept at a temperature near -30° c. Foils were examined by transmission electron microscopy using a Philips EM 200 electron microscope. 11) RESULTS AND DISCUSSION 1) Structure and Morphology. Fig. 1 shows the martensitic phase in the alloy containing 1.8 at. pct Si. This phase is composed of contiguous platelets, each containing striations. The direction of the striations changes at the boundary between individual platelets. These internal markings resemble the striations that are usually identified as stacking faults, as for example in Cu-A1 martensites6-a or the lamellar mixture of two close-packed phases in Cu-Zn-Ga marten-sites.3p &apos;9 lo In the present alloys, selected-area diffraction experiments have been obtained in order to determine the nature of the striations. Figs. 2(a), (61, and (c) are electron diffraction patterns of an area inside a single martensite plate. Fig. 2(a) contains diffraction spots which correspond to two close-packed structures with different stacking sequences, namely ABCBCACAB (orthorhombic) and ABC (fcc). Spots belonging only to the fcc structure are indicated by arrows. By tilting the foil either the orthorhombic structure, Fig. 2(b), or the cubic structure shown in Fig. 2(c) may be obtained. When the foil is oriented so that only the diffraction spots of the orthorhornbic structure are present, bright-field illumination shows small lamellae, as seen in Fig. 3. In this figure the lamellae that belong to the fcc structure are bright bands inside the dark extinction contours of the orthorhombic structure. The boundaries of the lamellae are parallel to the basal planes of the orthorhombic structure and to the {Ill} planes of the cubic structure, the close-packed directions of both structures being parallel. The 5 pct Si alloy shows similar features as those described for the 1.8 at. pct Si alloy.

Jan 1, 1969

By H. C. Gatos, J. T. A. Pollock

It is well known that the superconducting critical current densities of many alloy superconductors may be increased by cold working and in some cases further enhanced by a short heat treatment. This latter enhancement has been attributed to the redistribution of dislocations into cell-like networks&apos; and to the precipitation of second phase particles,2&apos;3 which act as flux pinning centers. In a manner analogous to dislocation pinning in precipitation hardening alloys,4 it is expected that here also a critical distribution of the pinning centers should result in maximum pinning effect. Concentration inhomogeneities exist in most or all commercial alloys yet there have been only a few attempts made to determine their effect on critical current capacity in the absence of cold working. Sutton and Baker,5 and Kramer and Rhodes6 have found that the complex precipitation processes occurring during the aging of Ti-Nb alloys can result in critical current density enhancement. Livingston7-10 has clearly shown, for lead and indium based alloys, that the distribution of precipitated second phase particles is of critical importance in determining magnetization characteristics. However, these &apos;(soft" alloys age at room temperature and the time involved in specimen preparation prevents metallographic examination in the state in which the superconducting measurements are made. Thus results with such alloys are expected to be biased towards larger precipitates and interpar-ticle spacing. The present study of Ta-Zr alloys was undertaken to examine the influence of second phase precipitation, as controlled by heat treatment, on the critical current capacity of well annealed polycrystalline material. A study of the published phase diagram11 indicated that annealing supersaturated samples containing up to 9 at. pct Zr at suitable temperatures would result in the precipitation of a zirconium-rich second phase. It was MATERIALS AND PROCEDURE The alloys were prepared from spectrochemically pure tantalum and zirconium. Analysis was carried out by the supplier. Major impurities in the tantalum were: 12 pprn of 02, 17 pprn of N2, 19 pprn of C, and less than 10 ppm each of Mo, Nb, Al, Cr, Ni, Si, Ti. The crystal bar zirconium was pure except for the following concentrations: 15 pprn of 02, 17 ppm of C, 23 ppm of Fe, 11 ppm of Cu, and less than 10 pprn each of Al, Ca, N2, Ti, and Sn. Samples were prepared in the form of 8 to 10 g but-tons by arc melting using a nonconsumable electrode on a water-cooled copper hearth in a high purity ar-gon atmosphere. Each button was inverted and re-melted three times to ensure an even distribution of the component elements. The samples were then homogenized at temperatures close to their melting points for 3 days in a vacuum furnace maintained at 5 x 10-7 mm Hg. After this treatment the buttons were cold rolled to sheets approximately 0.020 in. thick from which specimens were cut, 0.040 in, wide and 1 in. long suitable for critical current density (J,) and critical temperature (T,) measurements. These strips were then recrystallized and further grain growth was allowed by an additional vacuum heat treatment at 1800°C for 60 hr. Some second phase precipitation occurred during cooling of the furnace and a solution treatment was necessary to produce single phase supersaturated samples. This treatment was successfully carried out by sealing the samples together with some zirconium chips in quartz tubes under a vacuum of 5 x 10-7 mm Hg, heating at 1000°C for 5 hr and then quenching into water or liquid nitrogen. The samples were then heat treated at either 350" or 550°C and quenched into water or liquid nitrogen. All samples which were heat treated at 350°C were quenched in both cases by cracking the capsules in liquid nitrogen. The samples treated at 550°C were quenched by dropping the capsules into water. Analysis for oxygen in randomly selected samples indicated that the oxygen content was in the range of 175 to 225 ppm. Values of Tc were determined by employing a self-inductance technique. Jc measurements were made at 4.2oK by increasing the direct current through the wire in a perpendicularly applied field until a voltage of 1 pv was detected with a null meter. The risk of resistive heating at the soldered joints during these latter measurements was reduced by first plating the ends of the wires with indium and then soldering to the copper current leads using tin. Metallographic examinations were performed after mechanical polishing of the same samples and etching in a 4H20:3HN03 (conc):lHF(conc) solution.

Jan 1, 1970

By J. B. Knaebel, M. W. Von Bernewitz

OUTSTANDING FACTORS that have largely induced the current great interest in the reopening of old mines and the search for new deposits are the increased relative value of gold, the certainty of a market for it, and the decreased activity and poor profits in other lines of endeavor. It is easy to understand why a miner out of a job and unable to find any other means of livelihood would naturally take to the hills with his pan, pick, and shovel; but never before have inexperienced, would-be prospectors and placer miners materialized from the factories and farms, the haberdasheries, and the oil and gasoline supply stations, in such numbers as the last couple of years have witnessed, except when rich strikes of the proportions of a Klondike have been made. What, may one ask, has occasioned this condition? Unemployment has put these men in a receptive frame of mind, and newspaper and magazine articles have done the rest-- The Gold Miner of Los Angeles (a new weekly), The Mid- Week Pictorial (New York) for Sept. 3, 1932, and Popular Science Monthly for August, 1932, for instance. Even the Saturday Evening Post had an article on a promising part of Colorado. Stories that good wages may be had for the panning in nearly every western state have been featured by daily papers, popular "scientific" magazines, and quasi- technical journals. These tales have been eagerly grasped by thousands of people whose ignorance of mining has only served to increase their enthusiasm.

Jan 1, 1932

By Shiou-Chuan Sun

THE presence of an excessive amount of tough froth in the flotation of minerals, particularly coals, may create trouble in dewatering, filtering, and handling. Froth is also a nuisance in many chemical industries.&apos; This paper presents a study on the destruction of extremely tough froths with intense high-frequency sound. The data indicate that sound waves can be employed for continuous atandsoundwavescan instantaneous defrothing. A powerful high-frequency siren was used in obtaining the data. Also tested was an ultrasonorator of the crystal type with a frequency range of 400, 700, 1000, and 1500 kc per sec and a maximum power output from its amplifier of 198 w. The results, not presented, indicate that as now designed this machine is not suitable for defrothing. Although the sound generators of the magnetostriction type2,3 and of the electromagnetic type&apos;.&apos; were not available, it is beelectromagneticlieved they are capable of producing the required sound intensity for defrothing. The use of ultrasonics for defrothing was suggested by Ross and McBain1 in 1944. Ramsey8 reported in 1948 that E. H. Rose mentioned a supersonic device that broke down flotation froth but with low capacity. The writer has not been able to find any published literature containing practical experiments. Theoretical Considerations The mechanism of defrothing by sound is attributed to the periodically collapsing force of the propagated sound waves and the induced resonant vibration of the bubbles. The collapse of froth is further facilitated by the sonic wind and the heat of the siren. Sound waves can exert a radiation pressure&apos;," against any obstacle upon which they impinge. When a froth surface is subjected to the periodic puncturing of sound waves, the bubbles are broken. According to Rayleigh9 and Bergmann,12 the radiation pressure of sound, P, in dynes per sq cm is given as: P = 1/2 (r+1)i/v where r is the ratio of the specific heats of the medium through which sound is traveling and is equal to 1 on the basis of Boyle&apos;s law; i is the sound intensity in ergs per sec per sq cm, and v is the sound velocity in cm per sec. In this case, the accuracy of the formula is only approximate, because a perfect reflection can hardly result from a column of froth. In addition to the radiation pressure, the propagated sound waves cause the bubbles of the froth to have a resonant vibration.&apos;" he vibratory motion of the bubbles causes collision and coalescence, thereby weakening if not breaking the bubble walls. Sonic wind and heat were also generated." The sonic wind can exert pressure on the froth surface, and the heat can evaporate the moisture content of the bubble walls as well as expand the enclosed air. Apparatus The defrothing apparatus, shown in Figs. 1 and 2, consists of a powerful high-frequency siren, a glass or stainless steel beaker of 2-liter capacity with 12.4 cm diam and 17.1 cm height, and a metal reflector. The beaker was placed 2 in. above the top point of the siren. The metal reflector was adjusted to reflect and focus the generated sound waves into the central part of the beaker. Fig. 2 shows the crystal probe microphone used to measure the acoustic intensity and the mandler bacteriological filter employed to introduce compressed air into the beaker for frothing. The apparatus was enclosed in a soundproof cabinet equipped with a glass window. The siren, shown in Fig. 3, consists of a rotor that interrupts the flow of air through the orifices in a stator. The rotor, a 6-in. diam disk with 100 equally spaced slots, is driven by a 2/3 hp, Dumore W2 motor at 133 rps. The frequency of the siren can be varied from 3 to 34 kc. The maximum chamber pressure is about 2 atm, yielding acoustic outputs of approximately 2 kw at an efficiency of about 20 pct. The siren itself is relatively small and can be operated in any orientation. A detailed description of the siren has been given by Allen and Rudnick.11 Collapse of Froth To study the sequence of the collapse of froth, the glass beaker was partially filled with 920 cc water, 100 g of —150 mesh bituminous coal, 0.3 cc petroleum light oil, 0.2 cc pine oil and 1.54 cc Pyrene foam compound. This mineral pulp was agitated for 5 min and then aerated through a mandler filter until the empty space of the beaker, approximately 9 cm high, was filled completely with min-

Jan 1, 1952

By ALEC CROWELL

Mississippi has had oil production for only the past six years and natural gas production of minor magnitude since&apos; 1926. The search for oil and gas commenced in 1903 and 1496 wells had been drilled in search of oil and gas up to Jan. 1, 1946. As the year 1945 ended, 659 wells were producing oil and gas from 23 separate reservoirs. The production for the year was 8,353,719,000 standard cubic feet of natural gas measured on a pressure base of 15.025 lb. per sq. in. abs., 15.316,009 bbl. of oil¬field water and 19,093,766 bbl. of crude oil and condensate. Production for the year 1944 was 2,636,067,000 standard cubic feet of gas, 14,979,793 bbl. of salt water and 16,420,346 bbl. of crude oil and condensate.

Jan 1, 1946

By T. A. Rickard

Slovenliness is as reprehensible in words as in clothes. Much writing that we recognize as poor in style is merely sloppy. Just as some students postpone the necessary shave or forget to change their collars, so young engineers in writing drop their articles, definite and indefinite, or omit prepositions where they are required, possibly to compensate for these they use unnecessarily The work will begin [on] Saturday. The work will begin [on] Saturday. `Influenza seriously affected many mines [during] the last three months. Flotation in America [during] the last two years has made tremendous strides. Construction of the mill started [on] August 12, 1915, at which time 75% of the excavation was completed. The idea I wish to convey is [that] there are mineral deposits to which the present law applies badly. For this reason, if there was [for] no other, the ownership of the ore below and [of] the surface above should go together. When a unit of mapping is furnished, be the unit a claim or [a] group of claims, it is necessary .. . A fully stocked store was started in Park City and all employees [were] sold merchandise on a strictly cost basis. The word "merchandise" is left without government or agreement. I suggest: ". . . and merchandise] was sold to all the employees on a strictly cash basis.". The verb `be&apos; is serving concurrently both as a principal and as an auxiliary in the following: At first the work was interesting and [was] liked by most of the men. The sulphide ore was more complex or [was] milled at an increased cost. The failure to repeat tie auxiliary verb in successive clauses is a common error, as in The filter is filled with liquid allowed to empty, and then ignited.

Jan 1, 1931

By Zay Jeffries

HOSTILITIES in Europe, Asia, and northern Africa were responsible for dislocations in rare-metal supplies during 1940. Although the consumption of some of the rare metals is small the dislocations may be relatively large. In some cases these are advantageous to North America and in others they are disadvantageous. Specific instances will be cited later. Barium T HIN films of barium metal on special steel balls greatly improve the life and reduce the friction of rotating anodes in highly evacuated small X-ray tubes and make possible the operation of these anodes at relatively high temperatures. These remarkable results are described in an article by Atlee, Wilson, and Filmer in the Journal of Applied Physics for September, 1940. Oil could not be used because of the high temperatures on the one hand and its volatility on the other. Fig. 3 shows diagramatically the rotating anode and the method of coating the steel balls with barium. The letters K.I.C. refer to "Kemet Iron Clad." The K.I.C. wire was mounted so that the barium could be evaporated by direct passage of the electric current. At high temperatures the barium dif-

Jan 1, 1941

By J. L. Bray

ACCELERATED programs, as discussed in this paper, refer to the year-around operation of a college or university with three sixteen-week or four twelve-week terms per year, with pauses between sufficient only to allow the administrative group to perform their functions. In most engineering schools, under such conditions, the conventional four-year course can be condensed to two years and eight months. These accelerated programs of study, which now exist in most of our technical institutions, were forced upon us under the influence of the outburst of wartime patriotism, perhaps one might go so far as to call it hysteria. Many of us felt and hoped that these programs were temporary expedients, but the cold hard threat of permanency now rears its head; consequently we should examine the merits and shortcomings of the new order, and evaluate its effect on our educational system, since it may persist in some form in the postwar years, because of the changing political and financial situation. Many engineering students are being educated in state supported institutions

Jan 1, 1944

By Samuel S. Wyer

Bethlehem Meeting, February, 1906 THE following abbreviations have been used in the text:¬ Am. MF. and Iron World. American Manufacturer and Iron World, Pittsburg, Pa. Can. Min. Rev. Canadian Mining Review, Ottawa, Can. Cass. Mag. Cassier&apos;s Magazine, New York, N. Y. Col. Eng. Colliery Engineer, London, Eng. Col. Guard. Colliery Guardian, London, Eng. Eng. and Min. Jour. Engineering and Mining Journal, New York, N. Y. Eng. News. Engineering News, New York, N. Y. Engr. Engineering, London, Eng. J. I. and S. I. Journal of the Iron and Steel Institute, Lon¬don, Eng. Jour. W Soc. of Engrs. Journal Western Society of Engineers, Chicago, Ill. Lond. Eng. The Engineer, London, Eng. Mines and Min. Mines and Minerals, Scranton, Pa. North of Eng. I. M. E. North of England Institute of Mining Engineers, Newcastle-on-Tyne, England. Oester Zeitsch f. Berg u. Hüt. Oesterrcichische Zeitschrift für Berg. und Hüttenwescn, Vienna, Austria. Pract. Engr. Practical Engineer, London, Eng. Proc. I. C. E. Proceedings Institution of Civil Engineers, London, Eng. Trans. A. I. M. E. Transactions American Institute of Mining Engineers, New York, N. Y. Trans. A. S. M. E. Transactions American Society Mechanical Engineers, New York, N Y Trans. Fed. I. M E. Transactions Federated Institute Mining Engineers, Newcastle-on-Tyne, England. Trans. I M E Transactions Institute Mining Engineers, Newcastle-on-Tyne, England.

Mar 1, 1906

By W. T. lsbell

HERCULANEUM, MO., about thirty miles south of St. Louis on the Mississippi River, is the site of the lead smelter of the St. Joseph Lead Co. The lead concentrates come by rail from the Flat River district and from three properties in Madison County, Missouri; from the Balmat division in St. Lawrence County, New York; a small tonnage from the Tri-State district; and occasionally from the Aguilar property in Argentina. The average grade is 67 to 68 percent lead and 1 to 3 oz of silver. The bulk of the material is flotation concentrate, with some gravity or table concentrate. No secondary metals, outside drosses, or any materials high in bismuth, arsenic, or antimony are treated. All concentrate is received in box-caps and is unloaded directly from a trestle into the concentrate bins at the roaster plant. Flux, coke, and any miscellaneous lead-bearing material is either unloaded directly into bins or unloaded with a locomotive crane. All moving and switching of cars is done with two thirty-ton steam locomotives. Shipping facilities for the plant are provided by the Missouri-Illinois Railroad. Water for the plant and for fire protection is obtained from a dam built in a near-by creek. Drinking water both for plant and town is obtained from

Jan 1, 1947

By H. Kenworthy, M. M. Fine

The progress made to date in the mineral dressing of complex Arkansas titanium ores is reported in this paper. Concentrates of rutile, a dioxide of titanium, were produced by treating a submarginal ore from the Magnet Cove Rutile Co., Inc., Magnet, Ark. The rutile recovery at present is 45 to 50 pct of the total TiO2 with the possibility of increased recovery with additional research. The work reported herein is part of a general study which will later include results of investigation of other titanium ore bodies in the Magnet, Ark., area. The fragile character of the rutile minerals, the softness of the gangue, the occurrence of pyrite and leucoxene, and the considerable proportion of extremely small size rutile in the presence of montmorillonite- and illite- type clays in the Magnet Cove open-pit mine are the important factors in the mineral dressing of this submarginal rutile ore.

Jan 1, 1949

By H. M. Howe

A Discussion of the paper of Professor Howe, presented at the London Meeting, July, 1906, and printed in Bi-Monthly Bulletin, No. 14, March, 1907, pp. 169 to 274. SECRETARY&apos;S NOTE.-M. Beutter&apos;s introductory remarks, being simply a resume of Prof. Howe&apos;s paper, with a disclaimer of the intention to criticise it, have been omitted, and the remainder of this contribution has been somewhat condensed, without omitting any essential statements. M. BEUTTER, St. Etienne* (communication to the Secretary-+):-Professor Howe observes in paragraph 47 of his paper that the fluid-compression of steel. diminishes piping by forcing the liquid and viscous metal, while the pipe is forming, or after it has formed, into the space so produced, and proceeds to study the different systems of compression, alluding to the four principal ones: Whitworth, Illingworth, Williams, and Harmet. Having now for many years had in use the last-named process, that of M. Henri Harmet, I shall attempt to explain the difference between it and the three other processes named. The Harmet process does not diminish or close the pipe after it has formed, but prevents it from forming; and I may add that it is the only one of the four which produces this result. It is true that the Whitworth process diminishes the interior hollow by localizing it around the central axis of the ingot, which is afterwards removed by trepanning the hollow forgings for which this process has been, I believe, always exclusively used. The Illingworth and Williams processes, which, in my opinion, are applicable only to small ingots, of necessity allow the pipe to form, or (to use the expression of Professor Howe) they allow the surface of the lake of liquid steel to sink into the interior of the ingot, since they involve waiting a certain time before compression, so that (in the case of the Williams process) the ingot-mold can be opened without dan¬ger, or (in the case of the Illingworth process) so as to avoid the risk that the steel may enter the grooves produced by the removal of the distance-bars. During the time required for

Jul 1, 1907