Search Documents

By C. N. J. Wagner, E. N. Aqua

Dilute Fe-Si alloys (0 to 5 wt pet Si) were cold-worked by making filings at room temperatuve. The analysis of the broadening of the X-vay powdev pattern peaks yields anisotropic particle sizes normal to the (110), (100), and (112) planes which are a consequence of deformation faults (probability a) and twin faults (probability p). The combined fault probability (1.5a +ß) increases from 0.01 in pure iron to 0.02 in Fe-5 pct Si. The root mean square stvains vary with crystallographic ovientation due to elastic anisotropy of the alloys, and increase from about 0.0035 in pure iron to 0.005 in Fe-5 pct Si measured in the [100] direction. Assuming that deformation and twin faults occur with equal probability, the X-ray data would imply that the stacking-fault energy does not change upon alloying. THE crystallographic aspects of the plastic deformation of dilute Fe-Si alloys has been studied many times since the observation of glide band structures by Barrett et a1.l These glide bands were much straighter than the wavy bands observed by Gough2 in unalloyed iron nearly 40 years ago. This difference in the morphology of the slip band structure has been verified many times, most recently by replication electron microscopy3 and dislocation etch-pitting methods.4,5 These observed differences in deformation behavior have been considered to result from the degree of cross slip that occurs in pure iron and in the Si-Fe alloys. The lowered tendency for cross slip would result from a lowering of the stacking-fault energy of iron by the silicon alloying addition. Experimental evidence for this lowered stacking-fault energy in the Si-Fe alloys, obtained with transmission electron microscopy, is the observation of dissociated dislocations in Fe-6 pct si6 and Fe-3 pct Si alloys,7 and the observation of sharply defined cellular substructures in Fe-3 pct si6,7 compared to the more diffuse substructure in zone-refined iron.' The activation energy for recovery of cold work is greater in the Si-Fe alloys than it is in pure iron, indicating that cross slip has become a more difficult process.9 The purpose of this investigation is to determine the change in stacking-fault probability from the broadening of powder pattern peaks in dilute silicon-in-iron solid solutions, when cold-worked at room temperature. The knowledge of the stacking-fault probability and the dislocation density, both of which can be deduced from line-broadening analysis of two orders of reflections from (110), (200), and (112) planes, will permit us to calculate the change in stacking-fault energy upon alloying silicon into iron. Previous X-ray investigation of cold-rolled Fe-5 wt pct Si (100)[001 ] single crystals did not reveal any line broadening, whereas cold-rolled Fe-3.1 wt pct Si (001) [110] and (001)[100] single crystals10 showed line bro2dening as a consequence of small particle sizes (-200A) and root mean square strains (-0.25 pct), which are comparable to those found in cold-worked iron filings.11 EXPERIMENTAL PROCEDURE A series of five Fe-Si alloys containing nominally 1 to 5 wt pct Si and pure iron were cold-worked by making filings at room temperature. The actual silicon content deviated at the most by +0.1 pct which is of no significance in the present study. The carbon contents of these materials were less than 0.02 pct. The X-ray diffraction patterns were measured with molybdenum, cobalt, and iron radiation using a GE and a Philips diffractometer. The (110)-(220), (200)-(400), and (112)-(224) pairs of reflections were

Jan 1, 1968

By H. E. Cline, T. H. Alden

A study zvas made of rate-sensitive plastic deformation and superplasticity in alloys of lead and tin. These alloys (lead, PO-19 pct Sn, Sn-38 pct Pb, Sn-2 pct Pb, tin) were extruded, aged at room temperature, or melted and resolidified to produce a variety of ~nicrostrnctures. Flow stress us strain rate data were obtained frorn tension tests for strain rates between 10-6 and 1 min-1. The curve log o .us log £ was S-shaped jor fine-grained materials and approxinzately linear for coarse-grained nzaterials. At constant grain size, the behavior was relatively insensitive to conposition. High rate sensitivity (d log o/d log k) and superplasticity occurred at intermediate strain rates in fine-grained materials and are believed to be associated with a transition with strain rate in the mode of plastic flow. This transition was shifted to higher strain rates with increasing temperataire or decrensing grain size. The high rate rneclzanisrn is presunzed to be slip, while rnetallographic evidence sug-gests that the low rate lnechanism is pain boundary sliding. PEARSON' discovered that extruded eutectic alloys of Pb-Sn and Bi-Sn could be elongated as much as 2000 pct in tension. The ability for stretching decreased with aging time or annealing to increase the grain size. At high strain rates, or if the material was in the cast condition, normal ductility was observed. Following deformation of the extruded Pb-Sn eutectic at low rates, Pearson observed an equiaxed granular structure on an initially flat surface, while rapid straining produced elongated grains. He attributed the large deformation in the extruded alloys to the persistence of extremely small grains to a temperature sufficiently high for inter granular flow. Avery and backofen2 measured the strain rate sensitivity of the flow stress, m = d In old In 6, in the Pb-Sn eutectic and established a correlation between m and the tensile elongation. In the extruded eutectic alloy the strain rate sensitivity was 0.1 to 0.2 at rapid rates and the elongation was small, while at low rates m increased to 0.4 to 0.6 and superplastic elongation was observed. They also noted a grain size effect. In the case of the cast Pb-Sn eutectic the strain rate sensitivity remained at 0.1 over the range of strain rates of their experiment (3 x 10"3 to 2 min-I). These authors suggested that diffusional (Nabarro-Herring) creep was the mechanism by which deformation occurred at low strain rates, while climb-controlled creep occurred at high rates. Two predictions of this model are that, at low strain rates, the strain rate sensitivity approaches 1, i.e., Newtonian viscosity, and that the strain rate at constant stress varies as D/L2, where D is the coefficient of self-diffusion and L the grain size. More recently, a mechanical and microstructural investigation of the dilute superplastic alloy, Sn-5 pct Bi, has been done.3 The results show that the high strain rate sensitivity is associated with a transition with strain rate of the mechanism of plastic flow. At low strain rates, grain boundary sliding and its associated accommodation processes were evident, while at high strain rates quasi-uniform slip was concluded to be the dominant deformation process. The following experiments were performed to extend our knowledge of the phenomena of superplasticity to a larger range of strain rates, compositions, temperatures, and microstructures in the Pb-Sn alloy system. The question of why a cast structure does not exhibit viscous behavior although it appears to have a fine microstructure2 was investigated.

Jan 1, 1968

By R. D. Vaughn

The analysis of laminar flow of power-law non-Newtonian fluids in narrow, eccentric annuli is employed in this paper to discuss the problems of lubricant flow in journa! bearings and of errors introduced by eccentricity in experimental studies with concentric annuli on extruders and wellbore annuli. The velocity profile and pressure loss-flow rate equations are developed for the laminar flow region. In addition, the expected error in flow rate and pressure-loss measurements for concentric annuli as a result of eccentricity is determined. For example, a 10 per cent displacement of the core of an almost concentric annul us would cause a 1.8 per cent decrease in the observed pressure loss for a fluid with a power-law exponent n of 0.25. The corresponding increase in the observed volumetric flow rate would be 7. 5 per cent. INTRODUCTION Non-Newtonianism and eccentricity occur simultaneously in two engineering problems: (1) flow of lubricants in journal-bearings and pressure-reducing bushings, and (2) flow of non-Newtonian fluids in plastic extruders and wellbore annuli. The lubricants used for moving parts are often non-Newtonian in character — often they are plastic in behavior. A solution to the problem of flow of non-Newtonian fluids in narrow eccentric annuli is particularly pertinent to this problem. In all experimental studies of laminar flow of fluids in concentric annuli, such as in extruders and well casings, the error due to eccentricity must be estimated or studied. A number of publicationsl-4,6,7 have dealt with this problem for Newtonian fluids; however, I am not aware of work for non-Newtonian fluids. This work is directed to the non-Newtonian problem. Before the solution to the problem is given, the pertinent conclusions from the work on Newtonian fluids will be reviewed. Heyda 1 and Redberger and Charles 2 have published general solutions to the problem of the laminar flow of Newtonian fluids in eccentric annuli, apparently without knowing of the earlier work of Ca ld well 3 and Bairstow and Berry,4 which is reported by Dryden, et al. 5 Although several mathematical routes are encompassed by the work of these authors, the results appear to be equivalent. Redberger and Charles2 show that the error caused by eccentricity in concentric annuli is negligible for small diameter ratios (k < 0.5); however, for large diameter ratios (k + l), the error in the predicted flow rate can be as great as 100 per cent or more. Partial solutions to the problem are available from the work of Dryden,5 Tao and Donovan6 and Piercy, et a1.7 Tao and Donovan examined the case of flow in narrow, eccentric annuli (k + 1) with and without rotation of the annular core. These authors also reviewed previous work on this subject and verified their approach with experimental data. Dryden gives the solution for the limiting case of complete eccentricity or tangency. Piercy, et a l. published an early solution to the problem of narrow eccentric annular flow. The conclusions of Redberger and Charles2 and the experimental proof of Tao and Donovan6 both suggest that the region of large diameter ratios (k + 1) is of main interest and that the parallel planes approximation to the solution in this region is satisfactory. This method will now be extended to the laminar flow of non-Newtonian fluids in narrow eccentric annuli. THEORETICAL SOLUTION The geometrical aspects of the problem are illustrated in Fig. 1. To represent the non-Newtonian fluid the power-law model was selected. This model has many disadvantages which have been pointed out; nevertheless, its simplicity, its frequent and wide applicability justify its use in this work. Fredrickson and Bird8 and Savins9 have used it as a basis for a theoretical study of laminar flow of non-Newtonian fluids in concentric annuli.

Jan 1, 1966

By J. Chipman, H. Towers, M. Paris

A simple radioactive tracer technique is used to measure the diffusion coefficient of calcium ion in molten slags. In a slag of 40 pct Ca0-40 pct Si0,-20 pct Al203, Dc " at 1450°C is 1.3x10-6 cm&apos; sec-&apos;. THE application of the principles of thermodynamics to steel and iron making problems has proved so fruitful that the kinetic approach has tended to be neglected. It seems probable that in some reactions the rate-determining step is the dif-fusivity of the reactants or of the products. But knowledge of the diffusion coefficients of the constituents of liquid slag and metal is singularly lacking. The present work was undertaken as a first step toward supplying such data for slags. Furthermore, any additional information on the physical properties of liquid slags might be expected to help in elucidating their structure. It is essentially a preliminary investigation, the course of which was determined more by the necessity of establishing a method than by the immediate intrinsic interest of the results. For example, the selection of calcium ion to be studied was dictated by the suitability of the isotope Ca45 in that it is a simple emitter with a long half-life. Of the other ions commonly encountered in slags, the isotopes of iron and manganese have relatively complex radiations as well as the normal disadvantage of requiring control of the oxygen potential of the atmosphere; Mg27 and Al29 have half-lives measured only in minutes; Si3&apos; has a simple decay process but its half-life of 2.8 hr is too short for preliminary studies; the only useful oxygen isotope is the stable O18; and there remain only sulphur and phosphorus both of which have suitable isotopes but were rejected as being of less fundamental interest than calcium. Similarly a lime-alumina- silica slag was used in preference to calcium silicate primarily because of its low melting point and its capacity to form a glass on fairly rapid cooling. Literature Review Very few studies of diffusion in liquid silicate systems have been reported. In order to determine the origin of diopside inclusions in felspathic rocks, Bowen1 investigated the diffusion between diopside and various mixtures of albite and anorthite. Platinum crucibles were used with diopside, the heavier of the two liquids, forming the lower half of the cell and diffusion taking place against gravity. Change in concentration along the diffusion path was found by measuring the refractive index of the quenched glass. Nearly thirty years later McCallum and Barrett2 used essentially the same method to determine the diffusion coefficient of lime in lime-alumina-silica slags. In this case the interest was to find the rate-determining step in the process of slag attack on refractory materials. In an investigation of the kinetics of the sulphur reaction, Derge, Philbrook, and Goldman8 determined the diffusion coefficient of sulphur in a typical blast furnace slag by the simple procedure of melting a slag containing 2 pct S over an identical slag sulphur-free. They make no claim to a high degree of accuracy but suggest that D, is of the order of 10-6 cm2 sec-l. Other high temperature liquid diffusion studies have been concerned with metals. Holbrook, Furnas, and Joseph4 determined the diffusion coefficients of silicon, phosphorus, sulphur, manganese, and carbon in liquid iron by immersing a small carbon crucible containing pure iron-carbon alloy in a large vessel containing iron with a high concentration of the particular element. Their results were confirmed by Paschke and Hauttmann5 using a similar method. Diffusion coefficients in silicates in the glassy state have been studied by Johnson, Bristow, and Blau6 Both Na24 and Ca45 were used as tracers but only the

Jan 1, 1954

By S. R. Maloof, W. R. Mitchell, J. A. Mullendore

Preliminary experimental evidence is presented to show that the metallic impurities aluminum, iron, and silicon, and beryllium oxide as found in commercially pure hot-pressed beryllium powder can be reduced to lower Concentrations by Zone -Purification techniques. The reduction in the concentration of aluminum to extremely low levels (10 PPm) is noteworthy, since earlier work demonstrated that aluminum is a major factor contributing to the hot-tearing of beryllium during fusion welding. On the basis of present findings, a method is suggested for producing beryllium metal of improved weldability. EXPERIMENTAL research now being conducted on the purification of beryllium indicates that several of the metallic impurities and beryllium oxide can be reduced to lower concentrations by employing standard horizontal zone-refining techniques. For the preliminary work, commercially-pure hot-pressed beryllium having a purity of 97.84 pct was used. The chemical composition is given in Table I. The hot-pressed beryllium was machined into bars 5/8 by 5/8 by 4 to 6 in. in length. Beryllium-oxide boats which had been conditioned by prior heating in a vacuum of 10"5 mm of Hg at 1100°C for 3 hr were used to hold the beryllium while it was zone melted. The boat with its charge, along with a smaller beryllium-oxide boat containing scrap beryllium to be used for gettering purposes, was loaded into a quartz tube and evacuated to 10-6 mm of Hg. Alter alternately evacuating and flushing three times with purified argon, the furnace tube was backfilled to a pressure of 1/6 atm of A and sealed off by means of a vacuum-tight stopcock. It was then removed from the pumping equipment and mounted on the traveling carriage of the zone-refining apparatus. Heating was accomplished with a 10 kw 450 kc induc- tion heating unit using an induction coil consisting of two turns of 3/16-in. diam copper tubing. Before starting to zone melt, the atmosphere in the furnace tube was gettered by heating the scrap beryllium in the smaller boat to above its melting point and holding at temperature for several minutes. The carriage was then shifted so as to locate one end of the beryllium ingot in the large boat within the induction coil. A molten zone approximately 3/4 to 1 in. was established by loading directly into the ingot. The molten zone was moved very slowly along the length of the ingot. Before each pass was made the procedure for evacuating, flushing, and backfilling, and so forth was repeatedI&apos; Speeds of 1 1/2 and 3 in- per hr were used with up to twelve zone passes. The appearance of a typical zone-refined ingot is shown in Fig. 1. After zone refining, the grains in the ingot appear to be elongated in the direction of zone travel, whilst before, they are essentially equi-axed. A microexamination revealed the presence of a network in the beryllium grains as seen in Fig. 2. Laue spots in back reflection pictures taken of the sample were not sharp, indicating the presence of subgrains in the structure. As can be seen, however, many of the network boundaries cross beryllium grain boundaries. It has been shown by Martin and Moore1 that beryllium solidifies as a bcc structure which then transforms to the hexagonal structure at about 1250oC.It is believed that the observed network is merely the outline of the bcc structure which formed from the melt and are not subgrain boundaries. In order to eliminate surface contaminants, approximately 1/16 of an inch of material was removed from the outer skin of each ingot after zone refining.

Jan 1, 1962

By Herman Dykstra, Irving Fatt

Relative wetting phase permeabilities calculated from capillary pressure-saturation data are compared with measured relative permeability data. The equation relating relative permeability to capillary pressure-saturation data is derived by assuming that a porous medium is analogous to a bundle of capillary tubes. The equation includes a term to correct for the difference between fluid path length and length of core. Relative oil permeability data in the water-oil-gas system are presented, and it is shown that if the water is considered part of he rock matrix, the relative oil permeability curve is typical of a wetting phase relative permeability curve. Apparatus for measuring two and three-phase relative permeabilities are described. INTRODUCTION The difficulty in measuring relative permeability of cores has made it desirable to have a correlation between relative permeability and some more easily measured property of porous media. Such an easily measured property is the capillary preisure-saturation relation. In the past there has been a tendency to separate the capillary pressure concept from the very complex pore geometry and to consider that the capillary pressure-saturation curve give? only some characteristic distribution of interfacial curvature between two fluids.&apos; Recently, however, it has been realized that if capillary pressure data are to yield information concerning pore size distribution2 and fluid flow in porous media. the pore must be assumed to have a simple shape such as a cylinder or a sphere. Childs and George&apos; showed that relative water permeability could be calculated from the capillary pressure-water saturation curve by assuming that the pores are cylinders in which the fluid flowing obeys Poiseuille&apos;s Law, and that the capillary preisure curve indicated the size and number of pores. Purcell5 derived an equation relating the permeability of a porous medium to the capillary pressure curve by assuming the porous medium to he analogous to a bundle of capillary tubes. Gates and Lietz6 calculated relative permeability by an equa-tion derived from Purcell&apos;s equation. In this paper an equation is derived giving the relative water permeability as a function of water saturation by as-sulning that the core sample can be represented by a bundle of capillary tubes in which the fluid path length is not the same as the bulk length, and in which the fluid path length varies with saturation. THEORY For a bundle of N capillary tubes the flow through dN tubes will be dQ = qav dN ..........(1) where Q is the total flow rate through all the tubes and q., is the aberage flow rate through the tubes in the interval dN. If the interval dN is made small the average flow rate through a tube in the interval dN is given by Poiseuille&apos;s Law, 8 nl where ?P is the pressure drop across the tube of length 1 and radius r, and µ is the viscosity of the fluid. Substituting for qav in Equation (1), dQ =pr4 ? P/8µl dN.........(3) Darcy&apos;s Law for linear flow of an incompressible fluid in a porous medium is Q = KA?P/µL...........(4) where K is the permeability and ?P is the pressure drop across a bundle of tubes which has replaced the porous medium of length L and cross-sectional area A. Differentiating Darcy&apos;s Law with A, ?P, µ, and L constant, dQ = A?P/µL dK.........(5) Equating (3) and (5) gives dK------------dN.........(6) 8Al If the pores are assumed to be cylinders dV =pr2ldN..........(7) where V is the volume of flowing fluid in the pores. Substituting for dN in Equation (6) gives dK = —dV..........(8) 8AI&apos; By definition the saturation, S, of the core is v v S =V/Vp..........(9) Vv -PAL

Jan 1, 1951

By Irving Fatt, Herman Dykstra

Relative wetting phase permeabilities calculated from capillary pressure-saturation data are compared with measured relative permeability data. The equation relating relative permeability to capillary pressure-saturation data is derived by assuming that a porous medium is analogous to a bundle of capillary tubes. The equation includes a term to correct for the difference between fluid path length and length of core. Relative oil permeability data in the water-oil-gas system are presented, and it is shown that if the water is considered part of he rock matrix, the relative oil permeability curve is typical of a wetting phase relative permeability curve. Apparatus for measuring two and three-phase relative permeabilities are described. INTRODUCTION The difficulty in measuring relative permeability of cores has made it desirable to have a correlation between relative permeability and some more easily measured property of porous media. Such an easily measured property is the capillary preisure-saturation relation. In the past there has been a tendency to separate the capillary pressure concept from the very complex pore geometry and to consider that the capillary pressure-saturation curve give? only some characteristic distribution of interfacial curvature between two fluids.&apos; Recently, however, it has been realized that if capillary pressure data are to yield information concerning pore size distribution2 and fluid flow in porous media. the pore must be assumed to have a simple shape such as a cylinder or a sphere. Childs and George&apos; showed that relative water permeability could be calculated from the capillary pressure-water saturation curve by assuming that the pores are cylinders in which the fluid flowing obeys Poiseuille&apos;s Law, and that the capillary preisure curve indicated the size and number of pores. Purcell5 derived an equation relating the permeability of a porous medium to the capillary pressure curve by assuming the porous medium to he analogous to a bundle of capillary tubes. Gates and Lietz6 calculated relative permeability by an equa-tion derived from Purcell&apos;s equation. In this paper an equation is derived giving the relative water permeability as a function of water saturation by as-sulning that the core sample can be represented by a bundle of capillary tubes in which the fluid path length is not the same as the bulk length, and in which the fluid path length varies with saturation. THEORY For a bundle of N capillary tubes the flow through dN tubes will be dQ = qav dN ..........(1) where Q is the total flow rate through all the tubes and q., is the aberage flow rate through the tubes in the interval dN. If the interval dN is made small the average flow rate through a tube in the interval dN is given by Poiseuille&apos;s Law, 8 nl where ?P is the pressure drop across the tube of length 1 and radius r, and µ is the viscosity of the fluid. Substituting for qav in Equation (1), dQ =pr4 ? P/8µl dN.........(3) Darcy&apos;s Law for linear flow of an incompressible fluid in a porous medium is Q = KA?P/µL...........(4) where K is the permeability and ?P is the pressure drop across a bundle of tubes which has replaced the porous medium of length L and cross-sectional area A. Differentiating Darcy&apos;s Law with A, ?P, µ, and L constant, dQ = A?P/µL dK.........(5) Equating (3) and (5) gives dK------------dN.........(6) 8Al If the pores are assumed to be cylinders dV =pr2ldN..........(7) where V is the volume of flowing fluid in the pores. Substituting for dN in Equation (6) gives dK = —dV..........(8) 8AI&apos; By definition the saturation, S, of the core is v v S =V/Vp..........(9) Vv -PAL

Jan 1, 1951

By Benjamin F. Tillson

THE past seven years, and 1937 in particular, have witnessed the return of New Jersey iron mining to a place of importance. Following the World War period, little mining was done for several reasons. The properties were operated by small merchant furnaces whose demand was not sufficiently large to warrant large-scale methods with their attendant low operating costs. Under those conditions, the ore produced could not compete with that from the Great Lakes. However, when on Nov. 1, 1.929, the Alan Wood Steel Co., of Conshohocken, Pa., leased the Scrub Oak and Washington properties at Mine Hill and Oxford respectively, they made radical changes in the mining and milling processes which greatly reduced the cost of production and pointed the way to a renewed interest in mining in New Jersey. The following factors have been advanced as influencing the reopening of New Jersey mines:

Jan 1, 1938

By John F. Elliott, Robert D. Pehlke

The rate of reaction of nitrogen with liquid iron and with binary alloys of iron and Al, Cb, Cr, Ni, O, S, Si, and W were measured. The surface active elements, oxygen and sulfur, decrease the rate markedly. The other alloying elements have very little effect on the rate except when they function as deoxidizers, The rates of absorption and de-sorption were found to be equal. Several possible reaction mechanisms which may control the rate are considered. In order to describe completely the behavior of nitrogen in steelmaking processes, the mechanisms of mass transfer between the gaseous and liquid phases, nitrogen and iron, respectively, must be understood. A kinetic study to determine the nature of these mass transfer processes was undertaken, and the results of that investigation are presented in this paper. Specifically, the study was directed toward determining the influence of alloying elements on the rates at which pure nitrogen gas at constant pressure is absorbed and desorbed by liquid iron solutions: A previous paper1 reported measurements of the equilibrium solubility of nitrogen in liquid binary iron alloys. The experimental data are presented and discussed first and then several possible rate limiting mechanisms are considered. PREVIOUS RESEARCH The results of several investigations on the rate of absorption of nitrogen by liquid iron and iron alloys have been reported.2-14 There is little agreement on the rate coefficients among these studies because of the influence of geometry on the experimental system and of the purity of the liquid iron. The rate was found to be influenced by alloying content for the binary liquid iron systems: Fe-Al,2 Fe-C,4,6 Fe-Cr,4,5,8 Fe-Mn,5 Fe-Ni,5,8 Fe-O,9,10 Fe-O,9,10 and Fe-Si.2,6,7,11 Several investigators12"15 have reported that the rate of nitrogen absorption is increased in a reducing gas mixture and decreased in an oxidizing atmosphere. A mechanism for the retardation by oxygen of the absorption of nitrogen has been described by Naeser18 as the formation of an iron oxide film at the gas-metal interface. The film slows the absorption rate until it disolves in the metal, thus permitting nitrogen to enter the liquid iron. Karwat17 discussed the influence of oxygen in terms of the formation of gaseous molecules of nitrous oxide which represent a higher energy form than the nitrogen and oxygen or the oxidizing gas and consequently constitute an energy barrier for the process. Fischer and Hoffmann10 showed that the oxygen markedly reduces the rate of absorption of nitrogen, the rate constant being one order of magnitude smaller in liquid iron containing 0.15 to 0.24 pct 0 as compared to that in melts containing 0.001 to 0.02 pct 0. Although Chipman and Murphy2 reported that the rate of absorption of nitrogen in liquid iron was essentially independent of temperature, Eklund3 found that the rate increases strongly with increasing temperature as did Kootz4 and Saito.5,6 Karnaukhov and Morozov7 also reported a large temperature coefficient, but related it to increased stirring at higher power inputs in an inductively heated system. All of the authors above have treated their results assuming that the reaction is diffusion controlled, that the surface reaction is in equilibrium with nitrogen gas, and that a "first order" reaction takes place. Karnaukhov and Morozov7 and Humbert; who studied the rate of absorption in a closed system by observing pressure changes in the system as a function of time, concluded that their results best fit a diffusion-type analysis. This was further verified by von Bogdandy, Dick, and stranski18 and Fischer and Hoffmann10 who found the initial rate of

Jan 1, 1963

By F. D. Rosi, C. H. Mathews

THE plastic properties of face-centered cubic metals below room temperature present a field of investigation which has not been extensively ex-plored. The work by Schmid and Boas1 has demonstrated the importance of temperature upon such properties as strain hardening and critical resolved shear stress. The work by Yamaguchi2 upon the shear stress as related to the number of slip bands accentuates the necessity for further experiments of a similar nature. The approach to a mechanical equation of state from the standpoint of thermal fluctuations and activation energies by Becker3 and more recently by Kauzmann4 further emphasizes the need for a quantitative and more comprehensive analysis of the dependence of fundamental plastic properties on temperature. The purpose of the present work was to investigate specifically: (1) The gross shape of the stress-strain curves at several temperatures, (2) the change in the critical shear stress as a function of temperature, and (3) the number and appearance of slip bands as a function of strain and temperature. Preparation of Specimens Single-crystal specimens of 99.996+ pct alumi-num, 1/2 in. in diam and 5 to 6 in. in length, were made by the Bridgman method of gradual solidification from the liquid state. The crystallographic orientation of the single crystals was determined from back-reflection, Laue X-ray photograms ac-cording to the method described by Greninger.6 In most specimens the Laue photograms showed double diffraction spots indicative of the lineage structure type of imperfection, discussed in great detail by Buerger.7 The angular spread of these spots was never observed to exceed 2". Most of the crystals were radiographed to insure against microporosity. In preparing the metal surface for optical microscopy, the following sequence of operations gave good results: The as-cast crystals were turned down in a lathe, 0.001 in. per cut, to obtain a 2.5 in. gauge length. The cold-worked layer resulting from this operation was removed chemically by etching with Tucker&apos;s reagent. Then the specimen was polished mechanically through 2/0 metallographic emery paper, after which it was etched again to remove the cold-worked layer resulting from the mechanical treatment. A 48-hr anneal at 580°C ±10°C followed so as to insure an essentially stress-free single crystal. After the annealing treatment, the specimen was electrolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. With a current density of 10 amp per sq dm (decimeter) the time required to obtain a satisfactory surface varied from 10 to 12 min. The polish-ing was carried out for short periods of 2 min to avoid rapid deterioration of the solution as well as to enable the rotation of the specimen 180" for uniformity of polish. It was necessary to place the solution in a bath of dry ice in view of its explosive nature at room temperature. Etching of the electrolytically polished surface was accomplished by using the fuming etch-pit method recommended by Lacombe and Beaujard8 for high-purity aluminum. Method for Tensile Testing A modification of the loading equipment devised by Miller9 was used. In this apparatus, the specimen was suspended from a chain and gimbal arrangement (for axial loading) in a heavy steel framework connected at the bottom to a balanced 6:1 lever and bucket system. Loading of the specimen was accomplished by allowing sand to flow from a reservoir into the bucket suspended from the longer end of the lever-arm at a rate of approximately 3 lb per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire, strain gauge and an SR-4 portable strain indicator (type K), which permits a reading accuracy of 2 microinches per inch. For low-temperature study, the gauge was calibrated by measuring the elastic modulus of an annealed stainless steel rod, which is known to be independent of temperature."

Jan 1, 1951

By A. R. Gregory

A shear wave velocity laboratory apparatus and techniques for testing rock samples under simulated subsurface conditions have been developed. In the apparatus, two electromechanical transducers operating in the frequency range 0.5 to 5.0 megahertz (MHz: megacycles per second) are mounted in contact with each end of the sample. Liquid-solid interfaces of Drakeol-aluminum are used as mode converters. In the generator transducer, there is total mode conversion from P-wave energy to plain S-wave energy. S-wave energy is converted back to P-wave energy in the motor transducer. Similar transducers without mode converters are used to measure P-wave velocities. The apparatus is designed for testing rock samples under axial or uniform loading in the pressure range 0 to 12,000 psi. The transducers have certain advantages over those used by King, 1 and the measurement techniques are influenced less by subjective elements than other methods previously reported. An electronic counter-timer having a resolution of 10 nanoseconds measures the transit time of ultrasonic pulses through the sample; elastic wave velocities of most homogeneous materials can be measured with errors of less than 1 percent. 5- and P-wave velocity measurements on Bandera sandstone and Solenholen limestone are reported for the axial pressure range 0 to 6,000 psi and for the uniform pressure range 0 to 10,000 psi. The influence of liquid pore saturants on P- and S-wave velocity is investigated and found to be in broad agreement with Biot&apos;s theory. In specific areas, the measurements do not conform to theory. Velocities of samples measured under axial and uniform loading are compared and, in general, velocities measured under uniform stress are higher than those measured under axial stress. Liquid pore fluids cause increases in Poisson&apos;s ratio and the bulk modulus but reduce the rigidity modulus, Young&apos;s modulus and the bulk compressibility. INTRODUCTION Ultrasonic pulse methods for measuring the shear wave velocity of rock samples in the laboratory have been gradually improved during the last few years. Early experimental pulse techniques reported by Hughes et al.2 and by Gregory 3 were beset by uncertainties in determining the first arrival of the shear wave (S-wave) energy. Much of this ambiguity was caused by the multiple modes propagated by piezoelectric crystals and by boundary conversions in the rock specimens. Shear wave velocity data obtained from the critical angle method, described by Schneider and Burton4 and used later by King and Fate sand by Gregory, 3,6 are of limited accuracy, and interpreting results is too complicated for routine laboratory work. The mode conversion method described by Jamieson and Hoskins7 was recently used by King 1 for measuring the S-wave velocities of dry and liquid-saturated rock samples. Glass-air interfaces acted as mode converters in the apparatus, and much of the compressional (P-wave) energy apparently was eliminated from the desired pure shear mode. A more detailed discussion of the current status of laboratory pulse methods applied to geological specimens is given in a review by Simmons.8 A new shear wave velocity laboratory apparatus has been developed for testing rock samples under elevated pressures. This apparatus employs liquid-solid interfaces as mode converters. The technique for generating pure shear waves at liquid-solid interfaces was developed from studies of critical angle methods.6 Two identical transducers are placed in contact with opposite ends of the rock sample, one transducer acting as an ultrasonic energy emitter or generator and the other acting as an ultrasonic energy receiver or motor. The P-wave energy emitted from the piezoelectric crystal in the generator transducer is converted into pure S-wave energy at the Drakeol-aluminum

By T. B. Massalski, C. S. Barett

THAT metals and alloys of the body-centered-cubic structure tend to become unstable at low temperatures is so nearly universal that any exceptions are worthy of special attention. Studies of the exceptions may disclose unrecognized examples of metastability or may shed light on the nature of some of the factors that stabilize the body-centered-cubic phase. Among the structurally analogous body-centered-cubic 3/2 electron compounds, the ß-phase in the Cu-Zn system deserves further attention for, although this phase is known to undergo partial mar-tensitic transformation on cooling below room temperature to the temperature of liquid nitrogen when the composition is less than about 42 wt pct Zn, it does not transform on cooling .when there is more than this amount of zinc present.1-4 The present authors recently found that an alloy containing 48.35 wt pct Zn could be transformed, however, if deformed severely at room temperature or lower temperatures.V his discovery led to the suggestion that the jerky flow of ß-brass single crystals6 and some of the unusual temperature variations of the yield strength and hardness are due to strain-induced transformation during the tensile tests. The present investigation is an extension of that work to cover the entire available range of compositions of Cu-Zn ß-phase alloys and certain interesting compositions of the ß-phase in the Cu-Zn-Ga system. Particular attention is given to the structure of the transformation product resulting from cold work, which is found to vary with alloy composition, and to the temperature range in which transformation can be induced in the various alloys. The composition limits of the body-centered-cubic phase in the Cu-Zn system, based on a recent review by Raynor7 and the precision determinations of Beck and Smith: are shown in Fig. la; in the ß region the alloys are disordered and in the ß region they are ordered. The rate of ordering is so rapid that a high degree of order is found in any of these alloys immediately after quenching. Experimental The nine binary and four ternary alloys of this investigation were prepared from cathode copper (99.99 pct purity), electrolytic zinc (99.99+ pct), and gallium (99.98+ pct). All alloys were cast in transparent Vycor tubing, homogenized at temperatures between 800° and 890°C, and quenched in water. Ternary alloys were cast in small amounts (-5 g) to predetermined compositions to fall along a line of constant electron concentration in the ternary system. Changes of weight during the casting operation of the ternary alloys were not greater than 1 part in 2500 from the intended nominal weights and therefore their compositions were accepted without chemical analyses. All binary alloys were cast in larger amounts (100 to 150 g), homogenized, and hot rolled after preheating to 800°C. The central portion of the rolled strip of each alloy was annealed for eight days and quenched in brine. All binary alloys were analyzed chemically. The compositions, heat treatments, and metallographic appearances of all alloys are tabulated in Table I. Various samples were subjected to heat treatment or cold work at several temperatures and were then examined metallographically or by means of X-rays. Specimens about 6x6x3 mm in size were examined metallographic ally to confirm the presence of the ß-phase after quenching. Cold work was introduced by fastening each sample between two pieces of steel, cooling the assembly to the desired temperature, and transfering it rapidly to a vise where moderate or severe compression was immediately applied. Cold working at liquid helium temperature was done by a chisel-shaped tool mounted on an X-ray spectrometer, described elsewhere.% A!! metal-

Jan 1, 1958

By C. H. Li, J. A. Sarteli, W. Bonfield

The stress to cause a permanent micros train of 2 x 10-6 in. per in. (defined as the microscopic yield stress) in beryllium is found to be very sensitive to surface condition. The initiation of plastic flow in as-machined specimens, which contain a high density of twins and large residual compressive stresses to a depth of about 0.010 in. from the surface, occurs by the nucleation of slip from high stress fields around twin tips in the surface layers. Removal of the damaged surface layers by chemical polishing results in an appreciable increase in the microscopic yield stress, which is attributed to the remoual of stress raising twins rather than to the release of residual stresses. IT is well known that the macroscopic mechanical properties of beryllium are very sensitive to the nature of its surface finish. Matthews and coworkers1 have shown that the tensile strength of rolled beryllium sheet can be considerably enhanced by chemical polishing, presumably due to the removal of the high concentration of notches, twins, and large residual compressive stresses normally found in the surface layers of ground specimens. There was no similar effect of surface condition on the macroscopic yield stress (the stress to produce 0.2 pct strain), a point to which we shall return. To date there have been no extensive studies on the effect of surface condition on the microstrain region of beryllium. Recent measurements2 of the stress to cause a permanent microstrain of the order of 10-6 in. per in. on machined hot pressed QMV beryllium, gave values ranging from about 600 to 3500 psi. Reasons for the considerable scatter in the results were not discussed. In this paper, we wish to show that the microstrain region of polycrystalline beryllium is, in fact, very sensitive to surface condition. The stress to cause a permanent strain of 2 x 10-6 in. per in. which for convenience we will refer to as the microscopic yield stress, can be increased by almost a factor of 2 by minimizing the amount of surface damage. The variation of microscopic yield stress is attributed to the presence of twins in the surface layers, rather than to residual compressive stresses. EXPERIMENTAL PROCEDURE The starting material for this investigation was commercial purity hot pressed QMV beryllium, with an average grain size of about 20 . The effects of surface treatment were assessed by comparing the microstructure with residual stress measurements and microstrain properties. Specimens were prepared for metallographic examination by wet grinding with 240, 400, and 600 papers, followed by polishing with a suspension of fine alumina in warm 20 pct oxalic acid. After this treatment, the surface could be examined, either in the unetched condition with polarized light, or after etching in 2 pct hydrofluoric or boiling 20 pct oxalic acid with normal light. Thin films of beryllium suitable for electron transmission study were prepared from bulk specimens by chemical polishing with hydrofluoric and phosphoric acids, and were examined in an RCA-EMU-3 electron microscope. Residual stress measurements were made by a procedure similar to that of Treuting and Read.3 Specimens 4.0 in. by 0.625 in. by 0.080 in. were prepared by three different machining procedures, namely: turning, grinding, and sawing, in order to introduce different levels of residual stresses. An electrical resistance strain gage was attached to one side of the specimen, and that surface was then protected by an acid-resistant enamel, while the opposite surface was removed by etching approximately one thousandth of an inch at a time. The change in specimen curvature in the longitudinal direction was noted and the residual stress was calculated by the following formula:

Jan 1, 1963

By W. A. Backofen, D. H. Avery, W. F. Hosford

Sheets of the magnesium alloys AZ31B, HK31A, and ZE10A in several different tempers were tested in tension and determinations were made of the ratio of width-to-thickness strain. A marked increase in the ratio with tensile straining and a dependence upon alloy and test direction are rationalized in terms of a balance between the amounts of basal and prism-plane slip. All such variations are related, in turn, to the prevailing crystallographic texture. Fracture appearance is explained on the basis of anisotropy in plastic flow, and implications for developing texture -hardening effects in these alloys are discussed. ThE crystallographic texture or preferred orientation of a given material is determined by details of processing history. Such texture is known to influence many aspects of material behavior, in particular both the yielding and strain-hardening characteristics which are of special interest in the present work. Traditionally, the resulting plastic anisotropy has not been regarded as especially desirable. Earing in drawn sheet is perhaps the most common example of an unwanted effect of texture. However, it has also been recognized that suitable textures may be usefully employed to improve drawability,1,2 as a specific example, and generally to control yielding resistance under combined-stress loading.374 Texture would seem to be a detail of structure not yet exploited to nearly the fullest extent. A convenient basis for characterizing anisotropy in plastic behavior is the ratio of width-to-thickness strains obtained in a tension test;5&apos;6 the parameter is frequently labeled "R" and its value is revealing with respect to the nature of the prevailing texture. R gives a useful measure of a material&apos;s "thinning resistance". For an isotropic material, R = 1. With R > 1 the increased through-thickness strength in a sheet means greater resistance to yielding under biaxial tension, or "texture hardening";3&apos;4 if R < 1 the result may be a "texture softening" under the same loading conditions.4 Most R data relate to steel sheets for deep-drawing applications. Values for steel and other materials of cubic structures are not often much greater than 1 and nearly constant with strain in testing.1,2,7,8 To explore the implications of plastic anisotropy further, it was felt that experiments with much more strongly textured materials would be useful, and this led to the choice of magnesium alloys. The "ideal" sheet texture for magnesium contains the (0001) plane in the rolling plane, which ought to lead to R values approaching infinity. However, departures from the ideal texture, the possibility of slip in non-close-packed directions, and deformation by twinning would all be expected to introduce some range of R. Accordingly, studies on these materials were undertaken. EXPERIMENTAL Alloys in sheet form, Table I, were selected to obtain a variation in crystallographic texture, in the expectation that this would be reflected in differences in plastic anisotropy. Pole figures constructed by the Schulz surface-reflection technique9 were provided with the experimental materials by the Dow Metal Products Co. Profiles of pole density along great circles through the rolling (0 deg) and transverse (90 deg) directions were prepared from the pole figures and are collected in Figs. 1 and 2; considerable departure from the "ideal" (0001) alignment in the rolling plane is evident, with the largest angular spread in both directions being found in the ZEl0 alloy. Results of tensile tests on full-thickness specimens of 6-in. gage length by 1/2-in. width are given in Fig. 3 as engineering stress-strain curves* in rolling and transverse directions. All tests but one were made at a constant drive rate of 0.02 in. per min, and the final values of percent elongation at fracture, over the initial 6-in. gage length, are noted at the ends of the curves; one test on ZE10A-

Jan 1, 1965

By W. A. White

UNDERCLAY squeeze is the plastic flowing of underclay below coal pillars into mined-out entries and rooms. Squeezes may be caused either by wet mine conditions where the moisture is taken up by the clay—making it more plastic—or by the presence of certain clay minerals, such as mont-morillonite, which are plastic when there is enough natural moisture. Under either condition, sufficient stress will cause the underclay to flow. Squeezes may fill an entry or room within several hours, or it may be several months before movement stops. Squeeze areas commonly cover hundreds or thousands of square yards. The Coal Div. of the Illinois State Geological Survey has collected samples of underclays from various mines and from cores drilled by coal companies in the state. From these samples natural moisture content, particle size and particle size distribution, and clay mineralogy are determined. Data from samples collected from the underclay below Herrin (No. 6) coal in the Lumaghi Coal Co. mine near Collinsville, Ill., are used in this report to clarify points in the discussion. Data from samples taken from other mines lead to the same conclusions. A generalized geological section for the area is given in Table I. The underclay below coal No. 6 ranges from a few inches to 3 or 4 ft thick. The upper 6 to 18 in. are noncalcareous; the lower part becomes more calcareous with depth. Limestone nodules become larger with depth, almost grading into the limestone below. In areas where the clay is nearly absent the limestone may thicken to take its place; thus they may complement each other in thickness. There are two types of squeeze areas in a mine. In one type up to 3 or 4 ft of underclay lie in what appears to be a depression in the limestone underneath. This is suggested by a rim surrounding the squeeze area where the underclay is thin and the limestone lies within a few inches of the coal. In the second type the underclay of the squeeze area is surrounded by underclay of similar thicknesses which does not squeeze. Test Methods: Natural moisture content, particle size and particle size distribution, and clay mineralogy were determined by the following methods: Natural moisture is the moisture content a clay contains in its natural environment, expressed in percentage of the weight of ovendried clay (110°C or 230°F). To obtain the natural moisture content, given in Table 11, the clay samples were sealed in containers as soon as the samples were taken in the mines. Particle size and particle size distribution were determined by the pipette method,&apos; and the data were plotted as cumulative curves, Fig. 1, on semi-logarithmic paper. Particle size was plotted on the logarithmic scale and percentage on the arithmetic scale. The quartiles (diameters that correspond to frequencies of 25 and 75 pct) and medians (diameters that correspond to the frequency of 50 pct) of the samples were determined from these curves. The clay minerals were identified from the data obtained by differential thermal&apos; and X-ray powder" techniques. The differential thermal analyses were made on the whole samples, whereas the X-ray analyses were made on fractions of less than 2p. Data and Discussion Moisture Content: After the sealed jars had stood for 24 hr, those that contained squeeze samples had perspired, so that droplets of water had accumulated on the insides of the jars. Table II shows the moisture in the clay after it had perspired for 24 hr. (This perspiring was not noted in samples from nonsqueeze areas.) After perspiration one of the squeeze samples still had a higher moisture content than the samples that did not squeeze. Clay Mineralogy: The thermal analysis, Figs. 2 and 3, indicates that the clay minerals are chiefly micaceous in type; the low-temperature endothermal

Jan 1, 1957

By S. J. Matas, R. F. Hehemann, R. H. Goodenow

The hot-stage metallographic method has been employed to determine radial growth rates of upper and lower bainite. Lower bainite appears to grow as individual plates that increase in both length and thickness while upper bainite grows as sheaves of closely spaced plates or needles. A discontinuity in the temperature dependence of the growth rate appears to be associated with the transition from upper to lower bainite and stepped quenching experiments suggest that lower bainite will not continue to grow when the temperature is raised to the upper range. Thus, a single process does not appear to control the growth of both upper and lower bainite. A tentative model based on the forces acting on a dislocation interface is proposed to account for the slow growth of bainite. It has been recognized since the early studies of Davenport and Bain that a close relationship exists between the martensite and bainite transformations in steels. However, diffusion of carbon during the transformation has lead to considerable controversy concerning the reaction mechanism.1-7 Many studies4,5,7-9 have emphasized the structura and kinetic aspects of the bainite reaction and, in particular, the difference observed between the two forms of bainite—frequently termed upper and lower bainite. A kinetic difference between the two types of bainite has been revealed in the activation energy determined from the overall reaction;4,5 however, many difficulties arise in an interpretation of these activation energies since a number of temperature dependent factors contribute to the kinetics of the overall reaction. The displacive surface relief10 accompanying the bainite reaction permits a separation of the nuclea-tion and growth contributions to the reaction and allows the kinetics of the growth process to be examined. Several investigations of this type have been conducted; however, they have been restricted to the low temperature range.3&apos;6&apos;11 Here, bainite plates are observed to grow slowly in both length and width. The present investigation extends such studies to include the upper bainite range. MATERIALS AND PROCEDURE Materials. The composition of the steels studied in this investigation are presented in Table I. The range of composition permitted a study of the effect of carbon content on the growth rate of upper bainite in the 9 pct Ni steels and consideration of both upper and lower bainite in the higher carbon steels. These steels were received as hot-rolled rounds and were forged to approximately 1/2 in. thick plates for preparation of metallographic specimens. In order to produce an essentially zero carbon steel, Steel A was decarburized in wet hydrogen at 1550°F for 15 days with the result tabulated as Steel AD. Experimental Procedure. In order to study the slow growth of the displacive transformation product, a commercially available Leitz hot stage was modified to permit heating of the specimen by its own resistance in a manner similar to that employed by other investigators.6 The furnace chamber was maintained at a pressure of 2 to 3 X 10-5 mm Hg prior to austenitizing at 2000° ± 12° F for 5 min. Samples could be cooled from the austenitizing to the transformation temperature in approximately 15 sec and the progress of transformation was recorded with a 9 cm by 12 cm single frame camera or a 16 mm movie camera. RESULTS AND DISCUSSION Growth Characteristics. The general growth characteristics observed in this investigation were analogous to those reported previously.3,6,11 Typical growth sequences for the high temperature and low temperature forms are illustrated in Figs. 1 to 5. In both temperature ranges, bainite plates increase in length at slow, temperature dependent rates until interrupted by a grain boundary, another plate, or

Jan 1, 1963

By J. M. Roberts, N. Brown

The stress-strain behavior of zinc single crystals was measured over a strain range of 10-6 to 10-2. The phenomenon of macroyielding was observed in detail and plastic strains were detected at almost zero-stress. Closed hysteresis loops were observed during loading and unloading in the strain region of about 10-5. From the hysteresis a frictional stress on the dislocation of about 6 psi was obtained. A preliminary analysis indicates that impurities are primarily responsible for the friction. Nonelastic Strains as much as 10 -4 were recovered depending on the amount of prior deformation. Part of the recovered strain occurs instantaneously upon unloading and the remainder occurs at zero stress. The time dependence of the recovered strain was measured. THIS investigation is concerned with the details of plastic deformation preceding the ordinary yield point as measured with the usual strain sensitivity of about 10-4. The approach leads to internal friction observations in the hitherto neglected frequency range below 10-1 cycles per sec. It is believed that if the phenomenon of macroscopic yielding is to be understood, then the stress-strain curve in the neighborhood of the macroyield point should be greatly magnified. It may then be possible to determine whether macroscopic yielding is a unique event or whether it is a process which begins gradually at a lower stress. In the case of low-carbon steel a unique event obviously occurs at the macroscopic yield point as indicated by a drop in the load, but copper appears to exhibit a gradual transition from the elastic to the plastic state. In zinc the yield point is rather abrupt although the data indicates that some plastic deformation precedes large scale yielding.&apos; One of the purposes of this investigation is to determine whether there is an abrupt transition from the preyield microstrain region to the region of macroscopic deformation. Such a rapid transition would support the concept that there is a critical stress for yielding. The concept that yielding is a unique event associated with such phenomenon as activating a Frank-Read source, freeing the dislocation from solute atoms, dislocations cutting through dislocations, or dislocations moving freely by one another, has been expounded widely on theoretical grounds. It is hoped that highly sensitive measurements of strain in the neighborhood of the macroscopic yield point will shed some light on the event known as the "Yield Point". EXPERIMENTAL METHOD 1) Specimens—High-purity zinc was cast into spherical graphite moulds in air and grown into spherical single crystals by the Bridgman method under a positive pressure of Argon gas. Spectro-graphic analysis of cleaved sections from four crystals showed a purity of 99.994 pet Zn. The specimens were acid machined with an 1/8 in. gage section in a form similar to those used by Parker and co-workers.2 Bausch type grips were fastened to the specimen by Epon VI adhesive. The specimens were oriented so that only [1120] (0001) slip occurred. Fig. 1 shows two of the specimens in the grips. Prior to each test, the gage section of the specimen was given a concentrated HNO3 chemical polish followed by alcohol rinsing and air blast drying. 2) Test Method- The shear tests were performed on an Instron testing machine and the experimental set-up was made very "hard". Strain could be measured to a sensitivity of 10 -6 by means of a capacitance gage extensometer. The design and calibration of this type of extensometer to measure microstrain, as applied to pure shear and tensile tests of metals, will be the subject of a separate paper—therefore, only a brief account will be presented here. The method essentially consists of attaching a

Jan 1, 1961

By A. J. Stosick, J. R. Hoffman, E. Rudy, St. Windisch

The binary alloy system Mo-C zoas investigated by means of X-ray, metallog/aphic, thermoanalytical, and melting-point techniques on chemically analyzed specimens. The system, Fig. 39, is characterized by three congruently melting, intermediate phases, Mo2C, n MoCi-x, and aMoC1-,, of which only Mo,C is stable at temperatures below 1650°C. Substoichio-metrzc (~32.5 at. pct C) dimolybdenum carbide undergoes a homogeneous sublattice order-disorder transformation at temperatures of approximately 1400°C, whereas hyperstoichiorrletric compositions undergo a discontinuous Phase change. The order-disorder transitions in the Me, C phases are discussed in terms of the structural changes involved in the transformation processes and the absence of long-range sublattice coherency in stoichiometric or hyperstoiclziomet-ric compositions attributed to the impossibility of obtaining long-range order in a linear chain of alternating carbon atoms and vacancies. From the experimental phase relutionships and the known thermody-namic data for Mo2 C, limits for the free energies of formation for the high-temperature phases r) MoC1-, and aMoC1-, are deriued and found to be in good agreement with data previously obtained from phase equilibria in ternary metal-carbon systems. IN the course of studies of the high-temperature phase relationships in ternary systems of refractory transition metals with carbon,&apos; a number of inconsistencies found in previous work necessitated a reex-amination of some of the related metal-carbon binaries. A reassessment of the binary system data also seemed

Jan 1, 1968

By M. N. Pathasarathi, P. A. Beck, T. J. Koppenaal

EARLIER work1 indicated that in rolled and annealed copper the volume fraction of the cube-texture component may increase on continued isothermal annealing. Merlini found2 that in rolled copper the well-known increase in the amount of cube-oriented material with increasing annealing temperature3 is concurrent with grain growth, which takes place after recrystallization is complete. It was found that both in copper2 and in aluminum4 the texture resulting from primary recrystallization, even if this is followed by some grain growth, may in general comprise, in addition to the cube-texture component, four symmetrical texture components of the general type (123)[412], i.e., components not very far from the ideal orientations of the rolling texture. The volume fraction of the cube-texture component increases on further annealing at the expense of these four components.&apos; The present work was undertaken to study quantitatively the increase in the volume fraction of the cube-texture component in the course of normal grain growth, under varying conditions. Since the grain-gr3wth behavior of A1-Mn alloys has been already investigated in some detaiL5 an A1 + 0.8 pct Mn alloy was chosen for this work, in which the extent of normal grain growth can be effectively controlled by the inhibiting effect of a dispersed second phase. EXPERIMENTAL PROCEDURE High-purity aluminum of the following composition was used: A1 99.997 pct, Cu 0.0004 pct, Fe 0.0005 pct, and Si 0.001 pct. A high-purity A1-Mn master alloy was prepared by dehydrating manganese chloride at 500°C and reacting it with molten high-purity aluminum at 750°C in a graphite crucible.5 The Mn metal reduced from the salt by the molten aluminum goes into solution in the latter. The master alloy? containing 13 pct Mn, was solidified under conditions suitable for minimizing segregation. An ingot of the final alloy, to be used in the experiments, was per pared by melting high-purity aluminum and the necessary amount of master alloy in a graphite crucible, and by pouring the molten alloy into a graphite mold preheated to 700°C through a box containing graphite baffles designed to intercept most of the aluminum oxide films floating in the melt. The melt was then solidified by placing the mold on a water-cooled copper plate and by keeping the top of the mold hot, in order to minimize piping. The 6 1/2 in. long, 11/4-in.diam ingot consisted largely of a single crystal. Chemical analysis showed that there was little segregation from the bottom (0.83 pct Mn) to the top (0.81 pct Mn). Spectrographic analysis of the ingot showed that the impurity content remained essentially the same as that of the aluminum used. The ingot was processed so as to obtain a uniformly small grain size. without banding. The ini-tial steps of rolling in the form of a flat bar and of annealing, down through a thickness of 0.4 in., are shown in Table I. At this point the bar was cut into four sections, each approximately 3 in. long, which were processed separately as shown in Table If. The table also gives the penultimate grain sizes obtained in each section by annealing prior to the final rolling of 90 pct RA. During the final rolling the strips were reversed end to end between passes. Annealing treatments were given in a salt pot furnace, with the temperature controlled to 1°C. All annealing of section "6s" was carried out above the solvus point to avoid the formation of second-phase precipitate. The penultimate annealing was sufficiently short to give a relatively fine grain size in spite of the high temperature. Section "6L" was processed in a similar manner, except that the penultimate annealing was much longer, so as to allow considerable grain growth. Section "4" was given the two final

Jan 1, 1961

By Arthur H. Wilson

INTRODUCTION The stratified deposits of the coal measures are strongly laminated and exhibit a high degree of anisotropy. The stronger rocks in the sequence possess joints and shear planes, the coal itself has a closely spaced cleat pattern, and the softer rocks are capable of flowage. To calculate the general distribution of stress in such a medium by analytical means based on the theories of elasticity is difficult, and has not yet been satisfactorily achieved. Nevertheless, some estimate is required to aid the design of supporting pillars and permit the correct siting of main roadways. This is important when laying out districts for longwall extraction, particularly if the results of previous experience are not available in the area to be exploited. Although elastic stress analyses, including finite element analysis, may not be very appropriate, the basic equilibrium conditions will apply. These, combined with logical deductions based on observed fact, can be used to give appropriate solutions which experience has shown to be capable of giving acceptable results in the design of pillars associated with longwall workings. Constancy of cover load is one of the fundamental equilibrium conditions. When mining below ground, the cover is not removed, therefore the average vertical load after mining must equal the initial cover load. If mining produces a local decrease in load in any particular area, it must be balanced by an equivalent increase in load nearby. Bending moments in the strata above are capable of compensating for the turning moments which this redistribution of load may produce, and the existence of a "rear abutment", much discussed between 1950 and 1960, is not an essential equilibrium requirement. If the distribution of vertical stress is plotted three-dimensionally, then the load on any small element of area 6S will be o.6S, where o is the average stress. This also represents the volume of the "stress envelope" which lies above 6s. By making the individual areas very small and summing together, it is possible to show that the total load on any particular area can be found by calculating the volume of the stress distribution envelope which lies above it. A similar consideration applies to the stress distribution in a two-dimensional situation. If the stress distribution curve is drawn, then the area below any portion will represent the load per unit depth of section. For example, Figure 1 represents the possible stress distribution across a caved waste and associated ribside. If AW is the load deficiency [ ] These loads must balance, therefore area AW = AS, and if one can be deduced, the other will then be known. Attempts have been made to measure stress distributions in the ribside and in the waste. Stress meters in soft rocks such as the coal measures have not proved very effective. Those based on the measurement of strain have experienced difficulty in strata capable of flowage, high modulus stress meters suffer from cross sensitivity, and overcoming to obtain absolute stress is almost impossible. Load measuring instruments left in the waste have also proved largely ineffective, mainly as a result of the difficulties of protecting the leads in a caving environment. Certain logical deductions, however, can be made about the conditions in the waste. CONDITIONS IN THE WASTE Over the area of the waste the surface trough which develops is remarkably consistent, despite the geological variations which occur from coalfield to coalfield. In Britain, an accuracy of 210% is claimed for subsidence prediction based on width of extraction and depth of cover (National Coal Board, 1975). The subsidence in the USA is more variable (Adamek and Jeran, 1981), particularly with respect to the point of inflexion, but the same general pattern occurs. At the shallower depths the somewhat harder roof strata involved in the caving in the USA may suffer less compaction, giving reduced values of subsidence. Subsidence at intermediate horizons below the surface

Jan 1, 1982