Search Documents

By O. F. Kammerer, W. E. Miller, D. H. Gurinsky, J. Sadofsky, J. R. Weeks

Zirconium and titanium inhibit solution mass transfer of steels by liquid bismuth, mercury, and lead. It is shown that in bismuth and mercury, these adsorb on the surface of the steels and subsequently react with nitrogen and possibly carbon from the steels to form inert, adherent surface layers of ZrN, TiN, or TiN + Tic. Data are presented which describe the condition under which thase deposits form. These inhibitors decrease the solution rate of iron into bismuth, and require a higher supersaturation for precipitation of iron from bismuth. USE of the low-melting heavy metals (bismuth, lead, mercury, and their alloys) as coolants has been limited because solution mass transfer of steels occurs in these liquids; i. e., iron dissolves in the hot sections of the heat transfer circuit and deposits in the colder sections. The rate of solution of iron and the temperature coefficient of solubility are sufficiently great to cause complete or partial stoppage by the deposition in the coldest section of a closed circuit in finite time, even though the actual solubilities are extremely low. In the development of the mercury vapor turbine by the General Electric Co., Nerad and his associates1 discovered that the addition of as little as 1 ppm Ti or Zr to magnesium-deoxidized mercury reduced the mass transfer of ferrous alloys by mercury to a negligible amount. Reid2 reported that titanium was detected chemically on the surface of steels contacted with this mercury alloy in amounts varying from 2.0 to 2.6 mg per sq in., the greatest amount being found in the hottest portion of the circuit. Reid stated that the titanium forms the intermetallic compound Fe2Ti by reaction with iron on the surface of the steels. This compound was presumed to be highly insoluble in mercury. More recently, El-gert and Egan3 have reported a greater than 100-fold reduction in the rate of mass transfer of a 5 pet Cr steel by liquid bismuth upon the addition of titanium (in excess of 50 ppm) and magnesium (350 ppm) in the liquid metal, during experiments performed in thermal convection loops* over the temperature differential 700° to 615° C. Also, Shep-ard and his associates' have reported that the addition of titanium to liquid bismuth and Pb-Bi eutec-tic produced a marked decrease in the rates of solution of both iron and chromium from type 410 steel capsules under static conditions. This inhibiting effect increased with repeated reuse of the capsules. Tests performed in this laboratory under carefully controlled conditions have shown that the addition of zirconium and magnesium, or titanium and magnesium, to liquid bismuth or lead greatly reduces the rate of mass transfer of chromium alloy steels and carbon steels in thermal convection loops with a maximum temperature of 550°C.5-9 The present paper will review the data obtained to date at this laboratory on the behavior of iron and steels in contact with liquid bismuth alloys containing titanium or zirconium, and will attempt to explain the role of the above additives in reducing solution mass transfer. Reaction between the Zirconium or Titanium Dissolved In Liquid Bismuth and an Iron or Steel Surface Reaction between Zirconium Dissolved in Bismuth and the Surface of Pure Iron-—A small pure iron crucible (analyzed by the supplier to contain 0.8 ppm N was contacted with bismuth containing approximately 0.1 pet Mg and varying amounts of a radioactive zirconium tracer. The crucible was then inverted at the temperature of contact. The thin residual layer of adherent bismuth was dissolved in cold, concentrated nitric acid. The crucible surface and the solidified bismuth were then analyzed for radioactive zirconium. An analysis of the activity loss on the crucible surface and the weight loss of the crucible during the nitric acid treatment showed that the acid treatment removed the zirconium that had originally been dissolved in the adherent bismuth, but not any zirconium that may have reacted with the crucible surface. The crucible was then pickled in warm aqua regia to remove all surface activity, hydrogen-fired at 600°C, and recontacted with a new liquid alloy. The results of the experiments contacted 1 hr at 450°C show, Fig. 1, a Langmuir-type adsorption with an adsorption free energy of approximately 17 keal per g atom Zr.5 This deposit was estimated to contain 1 atom of zirconium for each 7 to 8 iron atoms on the crucible surface, assuming a surface roughness factor of the pickled crucibles to be five. Increasing the temperature to 520°C caused consi-

Jan 1, 1959

By D. S. Tomalin, D. F. Stein

The effect of reducing oxygen to low concentrations on the fracture of high-purity iron single crystals has been examined at 78° and 20°K. It is found that iron single crystals grown by the strain-anneal method usually contain a few occluded grain boundaries which may become embittled in the presence of oxygen, thereby nucleating cleavage fractures. High purity with respect to interstitial elements was found to inhibit twinning and evidence is presented for an orientation dependence of the resolved yield stress. Deformation occurred by slip rather than twinning at both temperatures of testing with elongations of as much as 9 pct at 20°K. THE fracture properties of iron single crystals have been observedl-3 to be a function of temperature, orientation, and purity. Allen, Hopkins, and McLennan1 demonstrated that at 78°K iron single crystals became increasingly brittle as the tensile axis approached the (001) pole of the stereographic unit triangle. Iron crystals with the tension axis near a (001) pole were completely brittle and orientations near the (011)-(111) boundary were very ductile, achieving a 100 pct reduction in area prior to fracture. Later work of Biggs and pratt2 and of Edmondson3 demonstrated that by reducing the carbon content of the single crystals the transition between brittle and ductile failure at 78°K could be shifted to orientations nearer the (001) pole. Ed-mondson went further and pointed out that any mechanism which tended to increase the yield strength of the iron (i.e., carbon addition, pre-strain) also increased the tendency for brittle behavior at 78°K. Thus by a reduction of carbon content Biggs and Pratt were able to obtain ductile behavior to within 20 deg of the (001) pole, and Ed-mondson was able to obtain ductile behavior to within 26 deg of the (001) pole. Edmondson's material had a total interstitial content (carbon, oxygen, and nitrogen) of approximately 60 ppm and, although Biggs and Pratt reported no analysis, indications were that their iron contained comparable impurities. Stein, Low, and seybolt4 purified iron single crystals to a total carbon, oxygen, and nitrogen content of approximately 20 ppm. They observed a lowering of the yield stress with this increased purity, and thus one might have expected an observation of increased ductility. Although they tested specimens of orientations which the previous workers had indicated should be ductile, the crystals failed at a 78°K in a brittle manner with little elongation. Stein noted,' however, that about 90 pet of the failures could be traced in origin to occluded grains. Allen et al.1 and Edmondson3 do not report examination of their cleavage surfaces, but Biggs and pratt2 reported that microscopic examination of the cleavage surfaces of many of their specimens revealed the presence of small occluded grains. Honda and cohen6 and Keh7 have also observed the initiation of fracture at occluded grains in iron single crystals. Therefore, the additional complication of occluded grains must be considered in studying the properties of iron single crystals and the origin of fractures determined if the ductility exhibited by the crystals is to be considered meaningful. Various investigators8-12 have studied the effects of impurities on grain boundaries in high-purity polycrystalline iron. Rees and Hopkins10 showed that the addition of oxygen to low-carbon (0.002 pet) iron weakened the grain boundaries, causing a shift from transcrystalline to intercrystalline fracture and a progressive decrease on the brittle-fracture stress with increasing oxygen content. In addition, it has been shown by Low and Feustel11 that the addition of carbon to polycrystalline iron containing oxygen eliminated grain boundary brittleness. Thus, oxygen can embrittle grain boundaries in high-purity polycrystalline iron, but the addition of an appropriate amount of carbon can eliminate the oxygen-induced brittleness. The oxygen content (19 ppm) of the iron "single crystals" employed by Stein el al. was large enough to suspect impurity effects at the occluded grain boundaries. Allen et al.1 Biggs and pratt,2 and Edmondson3 may have masked any occluded grain problem in their specimens considering the relatively high carbon levels they employed. stein13 demonstrated that the addition of as little as 0.9 ppm C to previously purified (less than 5 x 10-3 ppm C) "single crystals" would increase the elongation from a few percent to more than 20 pet at 78°K and the fracture was not associated with grade boundary initiation.

Jan 1, 1965

By Ray W. Carpenter, Ralph Hultgren, Raymond L. Orr

Heats of formation of Au-Zn alloys of compositions Au3Zn and AuZn were rneasured at several temperatures by liquid tin solution calorimetry. The data for Au3Zn show that much smaller heat and entropy effects are associated with the a2- a1 transformation than for the a1 - a transformation. This result is consistent with reported X-ray diffraction studies which indicate that the a1 and (a2 phases have ordered structures which only slightly differ, whereas the a phase is disordered. The heat of formation of AuZn(ß') does not change significantly between 322o and 8000 K, confirming that the ß' alloy remains highly ordered to high temperatures. Not many measurements have been made of the energies of order-disorder transformations in alloy phases. In many cases these energies may be conveniently determined by measuring heats of formation as a function of temperature. Many alloy phases approximately obey Kopp's law of additivity of heat capacities; as a consequence their heats of formation do not change with temperature. In ordered alloys, however, a decrease in degree of order with increasing temperature will contribute an endothermic component to the heat of formation. Thus, for ordered phases where other anomalous contributions to heat capacity in the alloy or its pure components are absent, a measured change in the heat of formation may be attributed to the energy of disordering. A portion of the Au-Zn phase diagram1" is shown in Fig. 1. The composition AuZn(ß') has a well-ordered superlattice structure of the CsCl type at room temperature. The alloy is considered to remain ordered to its melting point,1 although, from X-ray diffraction data and electromotive force measurements of zinc activities, Terpilowski3 concluded that considerable disordering began at -673°K. The Au3Zn composition is a disordered fee solid solution (a) at high temperatures. Between 693o and 543oK, the ailoy orders to form the a1 phase, having a structure based on the L12(AuCu3) type, but with a regular distribution of ordering faults in the c direction, making it tetragonal. Below 543oK, the alloy orders further by means of slight atomic shifts, without diffusion, yielding a complex long-period orthorhom-bic superlattice structure, a2.4-7 Heats of formation of Au3Zn(a2) and AuZn(ß') were measured at 363°K by Biltz et al.8 by aqueous solution calorimetry. Heat capacities of several alloys between 14.9 and 38.4 at. pet Zn in the range from 373" to 723°K were measured by Iwasaki ef al.6 Stoichiometric Au3Zn, however, was not included in the alloys measured, the nearest composition being 26.1 at, pet Zn. Also, the heating rate used for the measurements, 2 deg per min, may not have permitted equilibrium to be reached in the neighborhood of the transformations. Heat contents of solid and liquid AuZn were measured between 488o and 1138°K by Kubaschewski.9 It was decided to determine the ordering energies of Au3Zn and to check on the possible disordering of AuZn by measuring the heats of formation of these alloys at several temperatures. The present paper reports measurements by liquid tin solution calorimetry of the heats of formation of the three phases of Au3Zn at temperatures within their regions of stability, and of AuZn at a low (322°K) and a high (800°K) temperature. EXPERIMENTAL Alloy Preparation and X-Ray Examination. Ten-gram ingots of Au3Zn and AuZn were prepared by melting weighed amounts of gold (99.95 pct Au) and zinc (99.99 pet Zn) together in sealed evacuated Vycor tubes at 1060°K, followed by rapid quenching. The resulting ingots were homogenized at 900°K for 10 days. The Au3Zn alloy lost no weight in preparation, the loss from the AuZn alloy was enough to introduce an uncertainty of only 0.1 at. pet in its composition. Filings for X-ray examination were taken from various parts of each ingot and strain-annealed at 723°K for 20 min in vacuo. The Au3Zn filings were quenched rapidly to retain the disordered phase. Diffraction patterns were determined with an X-ray dif-fractometer using copper Ka radiation.

Jan 1, 1968

By Yoginder P. Chugh

Elastic and viscoelastic behavior of three rocks-Tennessee sandstone, Barre granite, and Indiana limestone-was studied experimentally under uniaxial tensile stress. Cylindrical specimens of these rocks, about 1.0 in. diam and 2.0 in. long, were subjected to incremental constant stress history under uniaxial tension. The stress was held constant for a period of 40 min at each stress level. During this period, longitudinal and transverse strains on specimens were continuously monitored. The straintime history at each stress level was analyzed for elastic and viscoelastic parameters of a generalized Burger model. The viscoelastic parameters under uniaxial tensile stress were compared with those under uniaxial compressive stress. The experimental setup, experimental procedure, analysis techniques, and more significant results are described. This limited research effort clearly indicates the importance of the mechanical behavior of geologic material under tensile stresses.

Jan 1, 1975

By W. E. Rudolph, R. E. Baylor

DUE to its location in the Atacama Desert, one of the most barren of the earth's surfaces, Chuquicamata's water supply presents unusual problems. Yearly rain-fall averages less than one tenth of an inch at the plant. However, there are summer showers above 12,000 ft in the Cordillera to the east, the resulting run-off flowing through old river valleys buried beneath more recent volcanic formations, to be impounded within sediment-filled basins. This water emerges at springs where the outlets of these basins are blocked by lava flows, and here are formed the small streams which feed the only important river of the region, the Rio Loa. Chuquicamata's water is obtained from these springs and rivulets. [ ] The map above indicates four pipe lines from which potable and industrial water are supplied. Potable water, amounting to 4500 metric tons per day, is conveyed in the Toconce pipe line from springs 59 miles due east of Chuquicamata. This water is used not only for drinking, but also for boilers and other needs requiring high quality. For industrial water at the oxide plant, there are two 12-in. pipe lines from the Rio San Pedro, carrying a total of 17,000 metric tons per day of slightly brackish water. This water is at present used mainly for leaching and for hygienic purposes. Water Source Found For the present and future needs of the sulphide plant, it was calculated that at least 32,000 metric tons per day of make-up water would be required. For this purpose, a pipe line of 44 miles length was constructed to bring in the entire flow of the Arroyo Salado, one of the eastern tributaries of the Loa. The salt content of this water is so high (over 5000 parts per million of solubles, mostly chlorides) that it is highly detrimental to farming, and the Chilean Government had been studying projects to separate these waters from others of the Loa system in order to improve agricultural conditions in the fertile valley of Calama. So it happened that the Government was willing to award rights to the Arroyo Salado waters under agreement whereby the Mining Company removes waters from the Rio Loa system above Calama for all time. The outlet of these waters, after serving their purpose at the new concentrator and leaving the plant in tailing, is the Salar de Talabre, an old salt lake which presents fully ten square miles of surface to serve as an evaporating pan, the outlets having now been blocked by dams. Here the dry climate of Chuquicamata is a favourable factor, evaporation averaging slightly above 1/4 in. per day. The Toconce and San Pedro pipe lines have been functioning from 26 to 34 years, and through the use of special cleaning tools which were developed at the plant, as well as deaeration of the more active Toconce water, these pipes are now maintained at capacities which do not diminish as years go on. Constructing the Dam The Arroyo Salado pipe line design and construction involved certain special and interesting features, and inasmuch as this line and its intake works are solely for the needs of the new sulphide plant, more detailed description is given. The waters are impounded at a gravity dam constructed of concrete to a height of 100 ft above the river bed, keyed into the precipitous Dacite walls of the narrow canyon (barely 6-ft wide at the bottom, only 25-ft width at 50 ft above). A small secondary dam was built 100 ft down stream from the main dam, providing a pool of 15-ft depth to protect the main structure from flood flows over the spill-way during the rainy season. A system of four 36-in. syphons was designed for discharging these flood waters from the lower depths of the lake, in order to avoid eventual sedimentation behind the dam. The lake has a length of 3300 ft, and its water level is controlled by an adjustable spillway permitting draw-down of eighty inches, amounting to 41,000 metric tons of available capacity. This regulation is necessary because of wide fluctuations in stream flow between day and night due to freezing of feeders. During the construction of the dam the entire river flow was handled within a 36-in. pipe line some 2000 ft in length. As the excavations proceeded

Jan 1, 1952

PENNSYLVANIA ANTHRACITE LOCAL SECTION On Saturday evening, Jan. 31, 1914, about 40 members of the Institute met at the Hotel Sterling, Wilkes Barre, Pa., for the purpose of discussing plans for the formation of a local section in the Pennsylvania anthracite region. President Rand; Prof. Joseph W. Richards, of the Board of Directors; Dr. H. M. Chance, Chairman of the Committee on Coal and Coke, and Secretary Stoughton were among the guests present. R. V. Norris acted as Master of Ceremonies, and the arrangements were all made in advance by a Committee under the leadership of Charles Enzian, to whom an enthusiastic vote of thanks was accorded at the dinner. An address was made by President Rand, followed by .Professor Richards, who outlined the procedure necessary for the formation of a Local Section. Addresses were then made by W. J. Richards, F. W. Chase,. C. F. Huber, R. J. Foster, F. A. Hill, H. M. Chance, Bradley Stoughton, and others, after which a rising vote was taken, and it was unanimously decided to petition the Board of. Directors for the establishment of the Pennsylvania -Anthracite Local Section. More than the required number of members then signed -the petition, and President Rand announced the appointment of a Committee to organize the Section and arrange for a meeting in accordance with their By-Laws, consisting of R. V. Norris, W. J. Richards, R. J. Foster, Edwin Ludlow, C. F. Huber, Charles Enzian, Douglas Bunting, F. A. Hill, and J. M. Humphrey.

Jan 2, 1914

By William Kelly

An extensive swamp covers a large part of the town-site of Norway and adjacent laud. Through this swamp run two parallel oreformations. In the north one is the Aragon mine. The south one passes into the swamp on the Harrison property. On the edge of the swamp, about 1000 feet from the Aragon mine, a diamond drill, in the fall of 1889, located the ore-bearing formation and a probable ore-body. To explore further and develop this ore, the Penn Iron Mining Company proposed, in the spring of 1890, to sink a shaft. The drill had shown the depth of the glacial drift to be more than 60 feet. A test-pit near the location of the proposed shaft had struck, at a depth of 20 feet, an amount of water which a 200gallon pump was unable to lower. At the Aragon, a few years before, a shaft had been sunk to hard pan with great difficulty and many delays by the usual method of driving laths. Under the conditions it was decided to sink a caisson- or dropshaft. Two 40-horse-power boilers, a Lidgerwood engine with 4foot drum, and a good derrick were set up; and two No. 10 Kuowles

Jan 1, 1892

By M. Bevis, A. F. Acton, P. C. Rowlands

Defor~nation twinning and transformation twinning modes most likely to be operative in Fe-Ni and Fe-Ni-C martensites have been determined using a new theory of the crystallography of deformation t~inning.~ This analysis shows that potentially important conventional and nonconventional twinning modes1 have been omitted in previous analyses. Discussion is given on the relevance of the predicted twinning modes to the lattice invariant shear associated with the martensite transformation in steels and to anomalous deformation twinning in Fe-Ni-C martensites. THE two most important criteria which appear to govern operative twinning modes in metallic structures1 are that the magnitude of the twinning shear should be small and that the twinning shear should restore the lattice or a multiple lattice in a twin orientation. The latter criterion ensures that the shuffle mechanism required to restore the structure in a twin orientation is simple. These criteria have been adhered to in the prediction of twinning modes2"6 in bcc and bct single-lattice structures with axial ratios in the range y = 1 to 1.09 as, for example, encountered in martensite occurring in steels. Refs. 2 and 3 in particular consider the martensite transformation in steels and the twinning modes in these cases relate to transformation twinning, and hence the lattice invariant shear associated with the martensite transformation. The list of twinning modes which can be compiled from these sources is incomplete and the ranges of magnitude of shear considered could be unrealistically small, particularly in the case of deformation twinning. The latter consideration is supported by the fact that twinning modes with magnitudes of shear large compared with the smallest shear consistent with a simple shuffle mechanism have been established in, for example, the single-lattice structure mercury7 and the multiple-lattice structure zirconium.&apos; In addition the anomalous deformation twins reported by Ftichrnan4 to occur in a range of Fe-Ni-C martensites still remain unexplained. It is clear that a comprehensive analysis of twinning modes likely to be operative in martensite In steels is required. The results of the application of a new theory of the crystallography of deformation twinningg to these structures are presented in this paper. The theory has been used to determine all shears which restore the lattice or a multiple lattice in a new orientation with magnitude of shear up to a required maximum. The orientation relationships between parent and twinned lattices are not restricted to the classical orientation relationships of reflection in the twin plane or a rotation of 180 deg about the shear direction. PREDICTED TWINNING MODES Twinning modes which restore all or one half of lattice points to their correct twin positions will be referred to as m = 1 and m = 2 modes, respectively. These modes are the most likely to describe operative modes in single lattice structures. The bcc m = 1 and m = 2 modes which have magnitudes of shear s in the range s < 2 and s < 1, respectively, have been given10 and are reproduced here in Tables I and 11. Detailed discussion of the crystallography of these modes and cubic modes in general will be discussed elsewhere (~evis and rocker, to be published). The four twinning elements Kl, &,ql,7)2 as well as the magnitude of shear s are given for each twinning mode, and the twinning modes are given in order of increasing shear. Two twinning modes are given in each row of the tables, the twinning mode Kl, Kz, ql, q2 and the reciprocal twinning mode with elements Kl = K,, Ki = Kl, q: = q2, and 17; = ql. The m = 1 and m = 2 twinning modes which describe twinning shears with small magnitudes of shear and simple shuffle mechanisms in bct crystals with -y = 1 to 1.09 are given in Tables I11 and IV, respectively. On increasing the symmetry of the tetragonal lattice to cubic, that is making y = 1, all modes listed in Tables 111 and IV must reduce to crystallographically equivalent variants of the modes given in Tables I and 11, respectively, or become twinning modes with both shear planes as symmetry planes in the cubic lattice and hence not considered in Tables I and 11. With the exception of this last type of mode only those tetragonal twinning modes which reduce to modes 1.1, 1.2, 2.1, and 2.2 of Tables I and I1 are considered in Tables 111 and IV. For values of y in the range -y = 1 to 1.09 the tetragonal modes and the corresponding cubic twinning modes have approximately the same magnitude of shear. The twinning modes listed in Tables 111 and IV are therefore by the criteria given above the most

Jan 1, 1969

By K. E. Nelson

The effect of thorium and zinc variations on the strength and 100-hr creep characteristics of Mg-Th-Zn-Zr alloys was investigated. Optimum resistance to creep at 650° and 700°F are attainable within a certain range of thorium and zinc contents. This range does not conform to that which develops maximum tensile properties. RAPID advances have been made during the last few years in the development of magnesium alloys for elevated temperature applications demanding high resistance to creep. The beneficial effect of rare-earth metals on the creep resistance of magnesium alloys has been emphasized by a number of publications1-13 and such alloys are now in commercial production. The use of thorium as an alloying ingredient in magnesium was mentioned by McDonald and also in two Alien Property Custodian patent applications.10,17 The initial observation of Sauerwald that thorium contributes still higher creep resistance to magnesium than is attainable with rare-earth metals has recently been substantiated.&apos;" " In fact, it has been demonstrated that the useful temperature range of magnesium alloys is appreciably extended by the use of thorium. In all cases, it was observed that zirconium must be included in the alloys in order to render them fine grained and more readily castable. Several recent publications:2-27 indicate that a still further improvement in creep resistance and a further extension of the useful temperature range can be realized by the addition of zinc to alloys. The primary purpose of this paper is to present the results of a comprehensive study of the effect of zinc on the strength and creep characteristics of Mg-Th-Zr alloys. Compositions covering the range of thorium content from M to 6 pct and zinc content from 0 to 5 pct have been investigated. The creep characteristics at 650" and 700°F reported in this paper are based on results of tests of 100-hr duration. It is appreciated that creep tests of 100-hr duration might not yield adequate data for design purposes for parts with much longer expected life. However, for the purposes of the present discussion, it is felt that the combination of stresses and temperatures used in the 100-hr creep tests have yielded a clear representation of the compositional variation of creep resistance at the temperatures investigated. Creep tests of 1000-hr duration are now in progress on a few of the most promising alloys. Preparation and Testing of Alloys The alloys studied in this intensive investigation were prepared in 25 lb capacity mild steel crucibles. The thorium, zinc, and zirconium were alloyed and poured as described in earlier publications The thorium was introduced into the melt in the form of a Mg-Th hardener," the zinc added in the metallic form, and the zirconium alloyed in the form of the commercial hardener containing magnesium and 30 to 50 pct Zr.10, 26 Fluxing practices for melting and refining were the same as for magnesium-rare-earth metal-zirconium alloys. The melts were sampled for analytical determinations and poured into separately cast 1/2 in. diameter standard tensile bars. The test bars were given a precipitation treatment of 16 hr at 600°F in laboratory furnaces. It has been shown by other tests that a high temperature solution treatment followed by an aging treatment is unnecessary for the development of optimum properties in Mg-Th-Zn-Zr alloys. The selection of 600°F as the aging temperature was based on an attempt to achieve metallurgical stability without coalescence of the undissolved phases and the attendant loss in strength. The thorium, zinc, and zirconium contents of each melt were determined chemically. The zirconium contents are reported in two parts, "soluble" and "insoluble," referring, respectively, to the portions present in the alloy which are soluble and insoluble in dilute HCl acid. Distinction is being made between these two components of the zirconium content in the alloys because it has been found that only that portion of the zirconium content which is soluble in dilute inorganic acids affects the structure and properties of the alloys. The usual impurities consisting of copper, iron, manganese, and nickel were determined spectroscopically. The analysis for each melt is listed in Table I. A description of the methods of tension and creep testing has been detailed in earlier papers. The tests were performed with the cast skin re-

Jan 1, 1954

By C. S. Barrett, A. Smigelskas

There have been no publications of the deformation and recrystallization orientations of the metal beryllium, yet pronounced textures would certainly be anticipated since it is close-packed hexagonal in structure. Having an axial ratio approximately that of magnesium, beryllium probably deforms by nearly the same slip and twinning mechanisms that operate in magnesium, and the textures are likely to be similar or but slightly different from the magnesium textures. In the tests reported below this is found to be the case; the textures are found to differ from those of magnesium only in the details of the scatter from the average orientation. This report covers not only samples rolled at room temperature, but some rolled at elevated temperatures. Since magnesium has been suspected by some investigators of altering its crystallo-graphic deformation mechanism at elevated temperatures, it was considered possible that beryllium might do so and alter its textures accordingly. No pronounced alterations were found, however. Unfortunately, the theory of deformation textures is not in a state of development that permits one to deduce the deformation mechanism from a knowledge of the textures, which means that the similarity of textures at different rolling temperatures, reported here, cannot be taken as definite evidence that the deformation mechanism is actually the same at all temperatures. The general similarity of the deformation textures of magnesium and beryllium also extend to the recrystallization textures of the two metals, judging by the pole figures for recrystallized sheet presented in this report. Samples were prepared in the form of composite sheets made up of small pieces stacked in a pile. Each piece was trimmed with scissors so that an edge was parallel to the rolling direction, dipped in paraffin, and assembled into the pack by aligning it under the cross hair of a microscope. As the desired orientation was obtained on each piece it was secured in place by touching with a hot wire to melt the paraffin. A stack of ten or fifteen pieces was built up in this way, then trimmed to the shape of a T; the portion to be X rayed was then etched to the shape of a wire about 0.045 in. diam with 6N HCl. This method of shaping the sample is a modification of that used by Bakarian on magnesium.&apos; The absorption of the rays in the sample was so slight that it caused no difficulty in interpreting the films. Exposures were made with a 0.030 in. diam pinhole, using molybdenum radiation (40 kv, 25 ma, Type A film at 5 cm, 2 to 3 hr exposures). With the recrystallized specimens it was found necessary to oscillate the specimen so as to reduce the spottiness of the lines. A range of oscillation of 5" was SUB- cient to produce reasonably satisfactory patterns, though the quality was somewhat inferior to that of the deformation texture patterns, and only two degrees of intensity were read from the arcs on the films. Typical photo-grams for each of the deformation textures and the recrystallization texture are assembled in Fig 1. The pole figures were plotted in the usual way with the intensity of the various portions of the diffraction rings estimated by eye. Seven to nine films were made of each sample and each was carefully read in plotting the pole figures. Typical series included exposures with the beam normal to the rolling direction and at 11, 26, 41, 56 and 71" to the cross direction, plus two exposures with the beam normal to the cross direction, and at 11 and 79" respectively to the rolling direction. The rolling was in each case considered sufficient to develop the final texture: the reduction by cold rolling was 84 pct (from 0.0045 to 0.0007 in. thickness), following prior hot rolling in longitudinal and transverse directions and recrystallization; the reduction by hot rolling at 800°C was 90 pct (0.010 to 0.001 in.), following similar prior treatment; the reduction by rolling at 350°C was 88 pct (from 0.005 to 0.0006 in.) after similar prior treatment. The recrystallization texture was determined on a sample rolled at 350" to a reduction of 88 pct (0.0165 to 0.002 in.) after similar prior treatment, then mounted between steel strips to keep it flat and annealed at 700" in an atmosphere of argon. Discussion of Results The results of the X ray determinations are assembled in the pole figures of Fig 2, 3, 4 and 5 for rolling at

Jan 1, 1950

By Charles R. Keyes

I. Introductory,.......... 185 II. Hypotheses oF the Origin of OzaRk Ores..... 186 1. General Considerations........ 186 2. Schmidt-Leonhard and Gage View...... 187 3. Jenney Opinion.......... 187 4. Posepny Idea,.......... 188 5. Winslow-Robertson Hypothesis....... 188 6. Branner Proposition......... 189 7. Keyes Statement.......... 189 8. Van Hise-Bain Theory........ 190 III. Requirements of an Adequate WoRking-Hypothesis,... 190 IV. GeneRal Geotectonics of the OzaRk Region.... 192 1. Salient Aspects.......... 192 2. Geologic Formations......... 192 3. Character of Faulting...192 4. Extent of Flexing......... 193 5. Unconformity Inequalities....195 6. Warping of Strata...195 V. Classes of Ore-Deposits... 196 VI. Vadose ORe-ConcentRation,........ 197 VII. GeogRaphic DistRibution of the Ore-Bodies,... 199 VIII. Relation of ORe-Deposit to Geologic Structure... 201 1. General Occurrence of Ore-Bodies in Basins.... 201 2. Deposits of the Central Missouri District..... 203 3. Deposits of the Southwestern Missouri District.... 203 4. Deposits of the Northern Arkansas District... 305 5. Deposits of the Southeastern Missouri District.... 206 6. Synclinal Ore-Deposits of Other Districts.....207 7. Significance of Ore-Troughs in Prospecting... 209 8. Origin of the so-called Synclines,...210 9. Significance of the Cross-Bars of Joplin..... 213 10. Relation of Ore-Run to Ancient Relief-Features,... 215 IX. Direction of GRound-Water Circulation..... 216 X. VeRtical Range of Workable Ore-Bodies,... 218 XI. Oscillation of Ground-WateR Level...... 219 XII. Relations of Ore-Bodies to Lithoclasic Features,.. 220 XIII. PRimaRy Source of Ore-Materials,...... 220 XIV. Zone of Ore-Enrichment,......... 222

Jan 1, 1910

By D. I. Bardos, Paul A. Beck

A MARK, Boren, and westgrenl in their X-ray diffraction study of manganese alloys with 10 to 25 at. pct Si reported the occurrence of a phase with complex crystal structure in a Mn + 14.5 at. pct Si alloy after annealing at 800° or at 600°C. Recently Kuzma and Gladyshevskii2 identified Mn6Si as an R phase,3,4 the second binary R phase known. (A binary R phase was previously found in the Mn-Ti system by Waterstrat.5) A ternary R phase was reported earlier0 near the Mn-Si binary border of the Ti-Mn-Si system at 1000°C. In the light of the Russian work it now appears that this "ternary" R phase may be in fact an extension of the binary (Mn6Si)R phase. As already found by Amark, Boren, and Westgren, the corresponding binary phase is absent at 1000°C; the effect of titanium is evidently to stabilize it up to higher temperatures. In a recent paper Wieser and Forgeng7 gave the boundaries of this binary phase, which they referred to as 6. In order to re-examine the identity of this phase, an alloy of Mn + 14.5 at. pct Si was prepared by induction melting in helium atmosphere and annealed for 3 days at 800°C. The powder pattern, taken with an asymmetrical focusing camera of large dispersion and shown in Table I, was found to be that of the R phase, in agreement with the results of Kuzma and Gladyshevskii. For comparison, Table I also lists

Jan 1, 1965

By Charles W. Schwartz, Subash Kolluru

INTRODUCTION Creep of rock in situ, like most rock mass behavior, will be largely governed by the behavior of the natural discontinuities -- bedding planes, faults, and joints, in particular, Several past studies have investigated various aspects of the time-dependent deformation of rock discontinuities; examples include Amadei and Curran (1980), Engelder and Scholz (1976), Johnson (1975), Kaiser and Morgenstern (1979), Solberg et al. (1978), and Wawersik (1974). These studies have provided much insight into the general phenomenon, but they have also produced some inconsistent conclusions and left many unanswered questions. This paper will attempt to shed some light on one of these questions: What is the influence of stress level on the creep of unfilled rock joints? The discussion will follow a two-part approach to the problem: (1) laboratory creep experiments on small scale jointed specimens, (2) a simple theoretical mechanism to explain, at least in qualitative terms, some of the results from the experimental program. EXPERIMENTAL PROGRAM Uniaxial creep tests were conducted on intact and jointed samples of a specially formulated gypsum plaster "synthetic rock." Synthetic rock materials have several advantages over natural rock for long-term creep testing: (a) higher creep rates, (b) lower strength and therefore lower loading requirements, (c) simpler specimen preparation, and (d) more controlled and consistent properties. Gypsum based plasters have been used previously in studies of short-term strength and deformability of jointed samples (Patton, 1966; Einstein and Hirschfeld, 1973). Furthermore, Williams and Elizzi (1977) demonstrated that natural gypsum, at least, creeps in a manner similar to that of most other creep-susceptible natural rocks.

Jan 1, 1982

By Henry Emmett Gross

Two types of decline curves are considered and their applications are discussed. The first is the well-known semilogarithmic decline curve having the rate of production plotted on the logarithmic scale and the time on the horizontal scale. The other curve is the percentage of oil in the fluid versus cumulative production, and it is plotted on Cartesian coordinate paper. These curves are illustrated by carefully and adequately labeled graphs. Where conditions permit application of both types of curves for rationally determining the reserves of a well, both should be applied and the most conservative reserve should be chosen. Formulas are given for determining the economic limits. For a semi-l~~arithmic~decline curve the formula is: A = B X C X D X E X F or B = A/C ? D X E X F A = total monthly operating cost (average of past year), B = economic limit in barrels of oil per day, C = days in an average month = 30.4, D = market price of crude per barrel, E = 1-royalty, F = 1-gross production tax, G = water production in barrels per day at the economic limit, H =per cent oil in fluid at economic limit. The economic limit for a per cent oil in the fluid curve is: H = B/B+G X 100 The semilogarithmic decline curve is treated first. Straight-line extrapolations on semilogarithmic paper follow the compound interest compound discount law, hence the ensuing formulas derived from this law may be used in computing reserves for such extrapolations: [1___1/(1+Y)]

Jan 1, 1939

By Henry Emmett Gross

Two types of decline curves are considered and their applications are discussed. The first is the well-known semilogarithmic decline curve having the rate of production plotted on the logarithmic scale and the time on the horizontal scale. The other curve is the percentage of oil in the fluid versus cumulative production, and it is plotted on Cartesian coordinate paper. These curves are illustrated by carefully and adequately labeled graphs. Where conditions permit application of both types of curves for rationally determining the reserves of a well, both should be applied and the most conservative reserve should be chosen. Formulas are given for determining the economic limits. For a semi-l~~arithmic~decline curve the formula is: A = B X C X D X E X F or B = A/C ? D X E X F A = total monthly operating cost (average of past year), B = economic limit in barrels of oil per day, C = days in an average month = 30.4, D = market price of crude per barrel, E = 1-royalty, F = 1-gross production tax, G = water production in barrels per day at the economic limit, H =per cent oil in fluid at economic limit. The economic limit for a per cent oil in the fluid curve is: H = B/B+G X 100 The semilogarithmic decline curve is treated first. Straight-line extrapolations on semilogarithmic paper follow the compound interest compound discount law, hence the ensuing formulas derived from this law may be used in computing reserves for such extrapolations: [1___1/(1+Y)]

Jan 1, 1939

The Institute assembled in the library of the Sheffield Scientific School at 8 o&apos;clock, Tuesday evening, February 23d. Prof. G. J. Brush greeted the members present on behalf of the Government of the Sheffield School in a few words of cordial welcome, to which President Raymond responded. Dr. Raymond then delivered an address on the History of the Relative Values of Gold and Silver. The Council presented, through the President, a list of names of persons duly proposed for members and associates, with recommendation for election. The following gentlemen were unanimously elected: *Prof. George J. Brush,. .. New Haven, Conn. *Prof. Oscar D. Allen,. .. New Haven, Conn. *C. Constable,.....New York City. *Leven S Goodrich,.... Oxmoor, Jefferson Co., Ala. *Charles J. Nourse,.... Columbia, Lancaster Co., Pa. *J. W. Mickley,.....Hockendauqua, Pa. *Hugh Alex. Crawford,. ..St. Louis, No. *General Ario Pardee,. .. Hazleton, Luzerne Co., Pa. N. W. Lord,.....New Pork City. J. Holme Maghee,.... New York City. *George E. B. Jackson,. .. Portland, Me. *Charles W. Watkis,.... Salt Lake City, Utah. *Charles E. Hall,....Philadelphia. *Charles J. Duval,.... San Francisco, Cal. Joseph Gorlinski,.... Salt Lake City, Utah. * Alfred Wartenweiler,. .. Salt Lake City, Utah. Wilmot J. Bowen,.... Salt Lake City, Utah. *Joseph Stokes,..... Trenton, N. J. Jason P. Brown,.... Boston, Mass. *William Davis Hartshorne,. . Bethlehem, Hunterdon Co., N. J. *Henry Williams,.... Spanish Bar, Clear Creek Co., Cot. *Robert Forsyth ,....Chicago, Ill. *S. T. Wellman,.....Cleveland, Ohio. *H. C. Walton,.....Chicago, 111. *Andrew Roy,.....Columbus, Ohio. *James H. Rittenhonse,. .. Providence, Pa.

THE Institute assembled in the library of the Sheffield Scientific School at 8 o&apos;clock, Tuesday evening, February 23d. Prof. G. J. Brush greeted the members present on behalf of the Government of the Sheffield School in a few words of cordial welcome, to which President Raymond responded. Dr. Raymond then delivered an address on the History of the Relative Values of Gold and Silver. The Council presented, through the President, a list of names of persons duly proposed for members and associates, with recom¬mendation for election. The following gentlemen were unanimously elected: *Prof. George J. Brush, - New Haven, Conn. *Prof. Oscar D. Allen, - New Haven, Conn. *C. Constable, - New York City. *Leven S Goodrich, - Oxmoor, Jefferson Co., Ala. *Charles J. Nourse, - Columbia, Lancaster Co., Pa. *J. W. Mickley, - Hockendauqua, Pa. *Hugh Alex. Crawford, - St. Louis, Mo. *General Ario Pardee, - Hazleton, Luzerne Co., Pa. †N. W. Lord, - New York City. †J. Holme Maghee, - New York City. *George E. B. Jackson, - Portland, Me. *Charles W. Watkis, - Salt Lake City, Utah. *Charles E. Hall, - Philadelphia. *Charles J. Duval, - San Francisco, Cal. †tJoseph Gorlinski, - Salt Lake City, Utah. *Alfred Wartenweiler, - Salt Lake City, Utah. †Wilmot J. Bowen, - Salt Lake City, Utah. *Joseph Stokes, - Trenton, N. J. †Jason P. Brown, - Boston, Mass. *William Davis Hartshorne, - Bethlehem, Hunterdon Co., N. J. *Henry Williams, - Spanish Bar, Clear Creek Co., Col.. *Robert Forsyth, - Chicago, Ill. *S. T. Wellman, - Cleveland, Ohio. *H. C. Walton, - Chicago, Ill. *Andrew Roy, - Columbus, Ohio. *James H. Rittenhouse, - Providence, Pa. * Members. † Associates

Jan 1, 1875

By John Chipman, Daniel Dutilloy

The equilibrium of gaseolis H2O-H2 mixtures with liquid iron-phosphorus alloys in the range 0 to 3 pct P is used to establish the increuse of the activity coefficient of oxygen, in the presence of phosphorus. Two different sampling techniques are used. THE importance of oxygen as a refining agent in steelmaking operations makes it desirable to improve our understanding of its behavior. Phosphorus which is always present in the ores has adverse effects on steel properties and its removal is necessary. The present study was undertaken to evaluate the interaction of oxygen and phosphorus in molten iron. Bookey, Richardson, and welch1 have studied the phosphorus-oxygen equilibria in liquid iron in the presence of lime. They used a mixture of hydrogen and water vapor to control the oxygen potential and worked with crucibles made of tetracalcium phosphate and lime. At low phosphorus concentration, i.e., at high oxygen, they observed a marked deviation in their results. They tentatively ascribed this to a large negative effect of oxygen on the activity of phosphorus. This was then included by chipman2 in his review of interactions in liquid iron. Pearson and Turkdogan 3 have later reported an interaction parameter They equilibrated a mixture of hydrogen and water vapor with an iron-phosphorus alloy contained in an alumina crucible and sampled the melt by suction in a silica tube. The solubility of oxygen in iron-phosphorus alloys has been studied by Levenets and Samarin.4 They reported an interaction parameter

Jan 1, 1961

By C. G., Fink

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution.

Jan 1, 1950

Discussion of the paper of BOYD DUDLEY, JR., presented at the New York meeting, February, 1915, and printed in Bulletin No. 96, December, 1914, pp. 2767 to 2782. H. 0. HOFMAN, Boston, Mass.-At the close of the paper Mr. Dudley said that his experiments in the laboratory had shown that it was possible to separate nickel from copper by means of a chloridizing roasting, but that in order to demonstrate a process of this kind, work upon a large scale would have to be carried out. I think it was in 1913, that experiments of this kind were carried out at the works of the Pennsylvania Salt Manufacturing Co., Philadelphia, in a Wedge furnace, and at Sault Ste. Marie in a Sjöstedt furnace. They showed a satisfactory separation of nickel and copper. The ore was first subjected to an oxidizing roast, then mixed with pyrite and salt, and given a chloridizing roast. A. H. Carpenter published in the Engineering and Mining Journal, vol. xcvii, p. 1085 (1914) the details of this work. The conclusion arrived at is, that if you subject sulphide ore to an oxidizing roast, finishing at the temperature at which all nickel sulphate is dissociated, i.e., 764° C., then mix it with pyrite and salt, and subject the mixture to a chloridizing roast between 600° and 700° C., you can chloridize a high percentage of the copper without chloridizing any of the nickel, and obtain thereby a satisfactory means of separating the two.

Jan 5, 1915