Search Documents

By John P. Dolan, Charles A. Einarsen, GiIman A. Hill

his paper discusses how the following formation characteristics can be determined mathematically from drill-stem test pressure charts: true formation pressures, effective permeability of the entire section tested, well productivities, wellbore damage, and possible detection of barriers (faults, pinchouts, etc.). This paper also presents a practical method for im-mediate determination of eflective permeability and well-bore damage from successful double shut-in pressure tests. A list of recommendations for improving the reliability of drill-stem rest pressures is also presented. INTRODUCTION A drill-stem test is a temporary completion designed to sample the formation fluid and to establish the possibility of commercial production. Early pressure recording devices were used merely to verify proper operation of the testing tool. Until recently the accuracy of the pressure gauges has been insufficient for any reliable quantitative use of the recorded pressures. In view of the need for more reliable formation evaluation and as a result of the recent interest in exploration work employing the concept of hydrodynamic en-trapment,1,2,3,4 better pressure recording gauges are now in use. These devices can record pressure within 1 per cent above 1,000 psig and can detect differential pressures as low as 1/2 psig. In addition to formation pressure, several other reservoir characteristics can be determined from DST charts; namely, well productivity, formation permeability, wellbore damage, and the possible existence of bar- riers (faults, pinchouts, changes in permeability, etc.). This paper presents a practical method to interpret DST pressure charts for formation pressures and many other reservoir properties, a method that has been developed in analyzing approximately 4,000 DST charts during the last five years. The techniques used are a composite of published articles on drill-stem testing5,6, together with well-known pressure build-up analysis methods. THEORY It has been shown7,8 that the following equation may be used for analysis of pressure build-up curves: Po - Pw = 162.6 qu/kh log ( to + ?/?) .....(1) When this equation is applied to the curves obtained in drill-stem testing, the assumptions and boundary con-ditions are more nearly realized than in conventional flow and build-up tests on producing wells. Zak and Griffen9 have recently discussed in detail the use of this equation in analyzing DST charts. One of the problems with DST curves is the lack of reservoir data for precise analysis. Therefore, it is necessary to develop empirical rules and field methods for analyzing DST charts in quantity. For this reason, the empirical methods presented in this paper have been developed, and their derivation is found in Appendices A and B. METHOD USED FOR ACCURATE READING OF DRILL-STEM TEST CHARTS In order to apply the pressure build-up theory to DST charts, it is necessary to obtain a digitized expression for the pressure and time data recorded by the pressure gauge. These data may be either provided by the service company or interpolated by projecting a

Jan 1, 1958

By Gerard Matthes

Only in recent years has any practical headway been made in the application of aerial photography to geological problems, and up to the present time its principal value to the geologist and mining engineer has been in "areal geology;" i. e., the study of formations as revealed at the surface. The object of this paper is to set forth briefly the principal advantages that may be derived from aerial photographic data in geological work and to serve in a measure as a guide to those who may be contemplating its use. Geophysical prospecting has for object the locating of mineral under the surface. Inasmuch as the geologist's chief complaint in life is a dual one—inability to see under the surface and inability to visualize comprehensively what he does see on top of the ground—geophysical prospecting coupled with aerial photography should do much to lessen his burdens. To what extent aerial photography can be made a useful adjunct to geophysical prospecting remains to be proved, but the inference drawn here is that it holds many alluring possibilities. To avoid disappointments, it should be stated at the outset that to the geologist or mining engineer an aerial photograph or mosaic is only a tool, the efficient use of which he must set out to master. Upon his skill and ingenuity in applying it to particular problems will depend largely the value of the results that he will obtain. Under the most favorable conditions an aerial mosaic, or even a few loose photographs, because of the exceptionally comprehensive oversight which they afford of field data, such as dips and strike observations at isolated outcrops, local indications of faulting, mineral and fossil finds, greatly facilitate study and correlation, save much tedious foot work, and may repay their cost many times. Even so, types of country may be found where the most skillful use of the best of pictures will produce results so meager as to render the cost of aerial photography entirely unwarranted. Between these two extremes will be found endless variations and possibilities. Hence no set rules can be promulgated. The safest procedure is to treat each case as a separate problem and to carefully weigh the relative advantages and shortcomings of aerial photography before embarking on its use.

Jan 1, 1928

By David R. Mitchell

THIS paper is limited primarily to a description of dry coal-cleaning processes in which air currents are used to effectuate a separation between coal and refuse. Processes depending mainly on differences in the coefficient of friction, resilience and shape are not described unless the use of air is necessary for the proper functioning of the process. The air cleaning of coal is of primary importance to the coal industry of the United States. From figures presented in the 1941 edition Mechannual,1 it is estimated that at least 12 million tons of bituminous coal was cleaned in the United States during 1940 by machines using air as the separating medium. One of the current problems confronting the coal-preparation engineer is the dry cleaning of small sizes and slacks. Progress in machine development for the cleaning of small sizes has been slow in recent years in the United States of America; it has been much more rapid in Britain and on the European continent. This paper does not attempt an exhaustive survey of all these developments, and only machines and processes that have found considerable commercial application are cited. Further, no critical analysis has been made of the theory involved in the separation of coal from refuse by processes using air as the separating medium other than that necessary for an understanding of particular machine designs and applications. HISTORICAL SUMMARY The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. The ingenuity of the early experimenters is to be marveled at in view of their lack of knowledge of the theoretical principles involved. As in other arts, practice has largely preceded theory. Yet, science and practice play a game of leap frog, now one ahead, then the other; the careful experimenter governs his efforts along practical lines by adapting his experiments to the limits prescribed by scientific laws. By first studying developments and the theory involved, it is not only possible to adapt processes to new uses but also to reduce materially operating cost and to build larger units without costly failures. Although many inventors have applied for patents for separating minerals by the use of air currents, the literature in regard to coal is meager. Berrisford2 describes briefly some of the early attempts to clean coal without the use of water. Several of the examples cited by him are reproduced herein. Fig. I shows a machine used for grinding and sizing, in which rollers running in a pan with a perforated bottom and fan opening on the side crushed the coal, which was then carried by the air currents to a settling chamber. The heaviest particles dropped out first and the light ones farthest away, as shown. In the year 1864, a machine was made that could be used as a sizer or to separate dirt from coal with a sized feed (Fig. 2).

Jan 1, 1942

By J. Volney Lewis

The following paper is based chiefly on work done for the North Carolina Geological Survey, and is presented here by permission of Professor J. A. Holmes, State Geologist. It represents, in a very general way, the field-results obtained during the summer months of 1893, and 1894, and part of 1895; and the portions pertaining to North Carolina are, to a certain extent, abstracts of a report shortly to be published as Bulletin No. 11 of the State Survey. Less emphasis, however, is here laid on the petrographic descriptions of the peridotites, and more detailed treatment is given to subjects pertaining to methods of mining, cleaning, and utilization of the commercial product, corundum. Some of the most extensive fields for investigation which this subject presents have been scarcely more than suggested.

Jan 1, 1896

By W. C. Elmore

THE magnetic powder method, long used. for roughly mapping mag-netic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the varia-tion of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing con-siderable light on the magnetic secondary structure of alpha iron4 and of nickels single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure.

Jan 1, 1936

By J. J. Stokes

Literature on the electrolysis of aluminum from cryolite melts and on the structure of these melts is surveyed critically. Data on density, freezing point, and other properties are reviewed. Theories of the electrolysis are examined in the light of these data. Two theories are presented which account equally well for the observations. ALTHOUGH the production of aluminum is a large-scale industrial process, consuming approximately 3 pet of all of the electric current generated in this country, the mechanism of the Hall Process remains a 70-year-old mystery. It is a remarkable fact that the aluminum industry, which was established largely through research and owes much of its growth to research, still employs as its basic process the one developed by Charles Martin Hall while he was still a young man working in a woodshed. There are, of course, modifications in detail and a tremendous expansion of the size of the units used, but basically the process employs carbon anodes and a carbon-lined iron vessel as a cathode for the electrolysis of alumina dissolved in molten salt. Of the almost infinite variety of salts available, the relatively minor Greenland mineral, cryolite, 3NaF.A1F3, is still the only one which gives good performance in the electrolysis. In the early days, the process was thought of as a simple one. The dissolved alumina dissociated and, during the electrolysis, the aluminum was carried to the cathode where it was discharged and collected in a pool of metal. The oxygen was carried to the carbon anode where it reacted to form primarily carbon dioxide together with some carbon monoxide. About the only virtue that can be claimed for this hypothesis is that of simplicity. The actual mechanisms must be tremendously more complex. This paper is devoted to a rather narrow part of the whole subject, namely, what ions are present in the bath, and by what mechanism the current is carried. The complexity of the literature on this system is demonstrated in Table I, which shows the ions postulated as being present during the process. This system is not easy to investigate. Cryolite melts at about 1000°C, so that all the investigations are at relatively high temperatures. Molten cryolite fumes in air, particularly if excess aluminum fluoride is present. The cryolite changes composition on heating at 1000°C, principally by reaction with moisture in the air, but apparently also by reaction with oxygen. Cryolite reacts with most of the customary materials of construction, and those that are not attacked by cryolite seem inevitably to react with molten aluminum. Graphite is the only common material that is inert to the electrolytic bath. Pure cryolite can be held in platinum. There is hope that some of the newer refractories will stand up in bath, and their development for this purpose would be a major advance in the field. The techniques to be discussed, then, are not the most advanced ones. Rather, they are examples of old standardized methods applied under difficult conditions. The principal methods that shed real light on the mechanism are density, electrical conductivity, freezing-point lowering, transport number, viscosity measurements, and reactivity of bath with carbon dioxide. The first measurement to be discussed is density. This procedure is relatively straightforward. A hollow platinum bob is suspended by fine platinum wire from an analytical balance into the melt being investigated. Density1-4 of the system sodium fluoride-aluminum fluoride is shown in Fig. 1. There is a maximum in the density near the cryolite composition, but actually the maximum is on the NaF-rich side of cryolite, close to the composition NaF - Na3AlF8. Density measurements are also useful in giving a clue to the nature of cryolite-alumina melts.1, 4 On the first addition of alumina, density decreases, Fig. 2, although the density of alumina, either solid or liquid, is higher than that of cryolite. These density results indicate that the systems are not simple. A great deal of effort has been spent in measuring the electrical conductivity of molten cryolite and of cryolite with various additives. Conductivity measurements are quite easy for fused salts that can be measured in a dip cell, but no successful dip cell has been made available yet for cryolite. Recourse is had

Jan 1, 1959

By J. M. Pilcher

The application of oil to coal for-the reduction of dust has greatly increased the consumers' satisfaction with solid fuels, especially those for domestic use. The combination of oil-treated coal and automatic firing by a small stoker has made possible clean, automatic heating with bituminous coal. This, with the added pressure of competition by other fuels, has caused a rapid development of oil treating practice. A variety of materials derived" from petroleum oils is available from which one may choose for treating a par-ticular coal. Until recently, however, little information had been published to guide the choice. It is most im-portant that the proper type and amount of oil be used in order that all coals marketed as "dustless" will be reason-ably dustless, and thereby maintain a good reputation for oil-treatment. During the past two and one-half years, an investigation of a number of the problems related to the treatment of coal with oil has been conducted at Battelle Memorial Institute. This project was jointly sponsored by Bituminous Coal Research. Inc., Standard Oil Company of New Jersey, Sun Oil Company, and Viking Manufacturing Company. A progress report giving the principal results of the work of the first year was presented before the American Society of Mechanical Engineers in December 1937.1 The present paper is a summary of the entire inves-tigation.

Jan 1, 1939

By Richard P. Rothwell

FIRES in mines are so serious in their consequences and of such frequent occurrence, that their causes and the means of extinguishing them are certainly questions of the greatest interest to a large part of the engineering profession. We have already, in this country, many mines which have been burning for years, and though our hard anthracite is so difficult to ignite that for a quarter of a century after it was first discovered it was not known how to burn it except with the aid of an artificial blast, yet most of the fires which have occurred underground have been in anthracite mines, and in the coal itself. The injury which these fires have caused to properties in various parts of the anthracite regions, and the cost of extinguishing them, would amount to many millions of dollars, and they have also occasioned the loss of many valuable lives. It is not surprising, therefore, that the subject has already attracted much attention, and the exercise of great ingenuity ; and the present communication is made less with the expectation of announcing anything new, than with the object of putting upon record the present state of our knowledge on this subject, or, in other words, of indicating how defective are the present means of combating underground conflagrations. (Causes of Mine Fires.-Even upon the surface, fire is a terrible foe to contend with, and there is probably no other which inspires such thorough and well-founded alarm. With what feelings, then, must we look upon this destructive element, when its field is in the narrow galleries of a mine, where the poisonous products of combustion, spreading in every direction, protect, in the most effectual manner, the fire itself from the attacks of extinguishers, while, if the face of attack be ventilated so as to enable them to approach the seat of the fire, the air current simply increases the extent and violence of the conflagration. Fires underground originate in as various ways as those on the surface, and it is scarcely necessary to say that, except in the rare cases where they are the result of design, they are invariably classed as " accidents," and most generally as " unavoidable accidents." In reality, by an intelligent understanding of their causes and with due precautions, they can almost always be prevented. Ignorance and

Jan 1, 1876

By George J. Young

DURing the spring of 1910 1 visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. Thc principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories. The commercial deposits are confined to the Tertiary period although

Jan 1, 1916

By P. A. Fisher, J. B. Wilson, D. J. Whitehead, C. J. P. Ball, A. C. Jessup

The properties of a new magnesium alloy ZT1 containing 3.0 pct Th, 2.5 pct Zn, 0.7 pct Zr are described. The alloy possesses good creep and fatigue resistance up to 650°F, is free from microporosity, and is readily sand-cast. ZT1 is shown to be superior to zinc-free Mg-Th-Zr alloys. THE advent of the jet engine created a demand for a light sand-casting alloy capable of being cast into large complex shapes and capable of resisting creep at temperatures up to 500°F. This demand has been largely met by alloys of the magnesium-cerium mischmetal-zirconium types, containing about 3 pct Ce mischmetal and 0.7 pct Zr, typified by Elektron magnesium alloys MCZ and ZREI, the latter alloy also having a zinc addition of 2.5 pct. These alloys utilize the valuable properties at elevated temperatures conferred by the addition of rare earth metals to magnesium, a fact which has been known for many years and discussed by several investigators.1-1 Murphy and Payne8 showed that the addition of the powerful grain-refining element zirconium to Mg-Ce mischmetal alloys produced alloys with attractive room temperature properties combined with good creep properties and castability. With the increasing power of modern jet engines the temperatures to which some of the magnesium parts are subject are likely to exceed the safe working range of the cerium-mischmetal-containing alloys, and at the beginning of the research considerable interest had been shown by aeroplane engine designers in a magnesium sand-casting alloy suitable for service at higher temperatures, e.g., 600°F and above. At an early stage in the development of this type of alloy a check on the fatigue properties at elevated temperatures indicated that, since the fatigue limit even at 108 eversals was appreciably higher than any permissible creep stress, the main emphasis of the research could be concentrated on creep behavior. The primary aim in developing the new alloy has therefore been to attain maximum creep resistance; but due consideration has also been given to other important properties such as castability, tensile strength, and cost. It is by now well established that it is not possible to correlate creep strength with other short time mechanical properties such as are obtained in tensile

Jan 1, 1954

By J. J. Kanter

There has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-temperature steels" are meant those specifically designed for service at elevated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service. Uses of Silicon Next to oxygen, silicon is the most widely distributed and abundant of the earth's substances. Although classed as a nonmetal, it is highly important in the metallurgy of all steels, having been used for years as an efficient and economical degasifier and deoxidizer. Silicon is added to various steels in the form of ferrosilicon, generally at the end of the heat so as to avoid oxidation losses. With acid steels it is added in the furnace (also in the ladle) and generally with basic steels is added in the ladle, so as to avoid reaction with the basic lining through high-temperature acidic reaction with silica, which may be formed by oxidation of the silicon alloy. Several grades of ferrosilicon are available, containing, respectively, 15, 50, 75 and 90 per cent Si. By far the largest tonnage produced is the 50 per cent grade although the 75 and 90 per cent ferro-silicons are used as ladle and furnace additions in the manufacture of steels of high silicon content. The introduction of silicon into steel as an alloying element is well known in connection with high-yield-strength constructional steel for bridges, ships, car construction, etc., and it is also well known as an alloy-

Jan 1, 1938

By J. J. Kanter

There has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-temperature steels" are meant those specifically designed for service at elevated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service. Uses of Silicon Next to oxygen, silicon is the most widely distributed and abundant of the earth's substances. Although classed as a nonmetal, it is highly important in the metallurgy of all steels, having been used for years as an efficient and economical degasifier and deoxidizer. Silicon is added to various steels in the form of ferrosilicon, generally at the end of the heat so as to avoid oxidation losses. With acid steels it is added in the furnace (also in the ladle) and generally with basic steels is added in the ladle, so as to avoid reaction with the basic lining through high-temperature acidic reaction with silica, which may be formed by oxidation of the silicon alloy. Several grades of ferrosilicon are available, containing, respectively, 15, 50, 75 and 90 per cent Si. By far the largest tonnage produced is the 50 per cent grade although the 75 and 90 per cent ferro-silicons are used as ladle and furnace additions in the manufacture of steels of high silicon content. The introduction of silicon into steel as an alloying element is well known in connection with high-yield-strength constructional steel for bridges, ships, car construction, etc., and it is also well known as an alloy-

Jan 1, 1938

By A. M. Skov, L. F. Elkins

Inclusion of anisotropic permeability in mathematical analysis of pressure transients observed during development of the huge Spraberry field indicates a major fracture trend which is in good agreement with that observed by fluid-injection tests spread over a 12- by 17-mile area. Delineation of this trend is important in selecting a pattern of injection for the pending large-scale water flooding in this field. Determination of reservoir parameters yielding best agreement between calculated pressures and observed reservoir pressures in newly completed wells was made using an IBM 650 computer. INTRODUCTION The Spraberry field covering 400,000 acres is a tight sand of less than 1-md permeability cut by an extensive system of vertical fractures. Primary recovery dominated by capillary retention of oil in the fractured sand matrix blocks is less than 10 per cent of oil in place. Strong forces of capillary imbibition of water into the sand, coupled with water flow under dynamic pressure gradient, indicate considerable increase in oil recovery can be achieved through water flooding. Best results will occur if the pattern of water injection is selected to force the water flow across the grain of the major fracture system. Existence of an oriented vertical fracture system in the Spraberry, observed first in cores, was highlighted more recently by the 144-fold contrast in permeability along and at right angles to the major fracture trend required to match relative water breakthrough times in Humble Oil & Refining Co.'s waterflood test there. Spraberry operators since have conducted two gas-injection tracer tests for further areal confirmation of the fracture trend. Re-analysis of early reservoir pressure transients for evidence of anisotropic permeability has permitted many more local determinations of major fracture trend without resort to further field tests. This paper is limited to updating analysis of reservoir pressure transients to include anisotropic permeability as a test for orientation of the major fracture trend in the Spraberry. The reader is referred to Refs. 1 and 2 for information about general Spraberry reservoir performance and to Refs. 3 and 4 for information about significance of fracture orientation in selection of the injection-well pattern for water flooding the Spraberry. RESERVOIR PRESSURE DATA—DRIVER AREA During early development of the Spraberry Driver area, Sohio Petroleum Co. made the extra effort to measure the initial pressure in each of the 71 wells in a 5-mile-long area immediately after completion. Progressively greater reductions in pressure ranging up to 400 psi were observed throughout the six-month development period. Detailed data are presented in Ref. 1. Since the reservoir oil was undersaturated some 300 psi initially, early reservoir performance involving 55 new well pressures is subject to analysis as flow of a single compressible fluid in a porous media. Assumption of uniform permeability in all directions yielded good agreement between calculated pressures and observed pressures of these wells in the earlier study,' but subsequent, additional, mathematical development to include anisotropic permeability in the transient pressure considerations and present availability of electronic computers to perform the much more extensive arithmetical calculations now yield even better agreement. The previous analysis, assuming uniform permeability, consisted essentially of calculating pressure reduction expanding circularly around each producing well and summing these effects at the time and location of each newly completed well for comparison with the measured pressure reduction. Permeability, effective fluid and rock compressibility, and permeability X thickness were varied until the best match with measured pressures was obtained. The present analysis, assuming anisotropic

By William Price

DURING the past three or four years, the fabricators of silicon-bronze alloys have endeavored to induce risers of phosphor bronze to use instead the silicon-bronze alloys, claiming that the silicon bronzes are superior to the phosphor bronzes for switches and springs, or where high fatigue resistance is desired. This paper gives the results of tests comparing several phosphor bronzes with a 3 per cent silicon bronze and a copper-nickel-tin alloy (Adnic), all processed by the Scovill Manufacturing Co. So far as the authors are aware, sheet-metal fatigue tests have not been made on any of the alloys included in this report, except on one phosphor bronze, material C, Table 1, which was tested by Townsend and Greenall1.

Jan 1, 1937

By W. A. Backofen, M. L. Ebner

SINCE the early work of Gough with Hanson and Wright,l-3 the study of fatigue has been characterized by experiments on single crystals only in recent times.9-10 Now, increasing attention is given to this aspect of fatigue research for the insight that it may provide into details of mechanism. The investigations have concentrated to a large extent on the development of deformation markings on fatigued crystals, and have shown the cracks to originate in slip bands possibly preceded or accompanied by slip-band extrusions. Experiments of special interest to the present work were conducted by paterson5 on copper crystals and involved both metallographic examination and measurement of change in flow stress. Crystals were cycled in alternating tens ion-compress ion with a constant plastic shear-strain amplitude of approximately 0.8 pct, and were particularly revealing for their demonstration of hardening with accumulated strain similar to that in unidirectional straining, through an easy-glide stage I followed by a stage II of rapid hardening; deformation was not continued beyond 40 cycles, however, so that the eventual course of the hardening curve could not be decided. For the conditions used by Paterson, surface slip markings were similar to those observed in unidirectional straining, but there were no X-ray asterisms and no deformation bands on the surface. In current thinking about the nature of fracture in fatigue, two views relative to mechanism are generally acknowledged, with the reservation that both could apply simultaneously in some measure. As one possibility, fracturing across a slip plane is regarded as a result of loss of cohesion from the creation of many point defects by dislocation movement under the cyclic loading.'' On the other hand, fracture has also been taken to follow as a consequence only of the geometry of slip at a free surface, consisting of offsets and crevices which eventually become fatigue cracks.12, l3 The work of McCammon and Rosenbergl4 showing fatigue in polycrystals at 4.2oK makes clear that any long-range diffusion of point defects is unnecessary, yet studies such as those of Forsyth and stubington15 show that accelerated diffusion may be a characteristic of deformation under fatigue loading. Interest in obtaining data of possible use for resolving such questions led to the experiments described below. Copper crystals were conveniently loaded in alternating four-point bending at constant deflection, a test condition shown to approximate a constant plastic strain amplitude for a wide range of axial orientations. The method of testing was not readily adapted to extensive study of temperature effects, but an investigation of the geometry of crack formation could simply be made by orienting,the slip direction at different angles to the surface. EXPERIMENTAL PROCEDURES Single crystals were grown by a modified Bridgman method in a stationary gradient furnace under an atmosphere of purified dry nitrogen. Purity of as-grown crystals was 99.999 pct as determined by spectrographic analysis plus vacuum fusion and gravimetric analyses for oxygen and sulfur, respectively. Crystals were of reasonable perfection as evidenced by a critical resolved shear stress at 10 deg from (110) of 60 g per sq mm and half-width of a (400) X-ray diffraction line from one crystal of

Jan 1, 1960

By H. E. Swanson

A description of the field apparatus has been published by D. G. Brubaker. Data from laboratory model studies of the in-line and broadside methods of operation are detailed. The conductor models include a single sheet conductor at several strike and dip angles and a schistose-type conductor. In addition, data on the effects of the strike length and of the depth of the conductor are presented for the broadside method of operation. All of the data show that the inclintion reverses direction over the top edge of dipping single sheet conductors. Differences between anomalies over conductors dipping between 90" and 30" are subtle,but flat-lying sheets can be readily distinguished from steeply dipping sheets. Schistose conductors are easily distinguished from single sheet conductors, and a procedure is given for determing the direction of schistosity. The depth of penetration under ideal conditions is 0.7 of the coil separation. In 1950, The New Jersey Zinc Co. (of Pa.) developed a lightweight apparatus for electromagnetic prospecting. A description of this apparatus has been published by D. G. Brubaker.1 It consists of a small, battery-powered vertical source coil and a direction-finding receiving coil. Source and receiver are kept a fixed distance apart and move as a unit along the survey lines. At each receiver station the inclination of the magnetic field created by the source is measured. Two methods of operation are used, in each of which measurements are taken with a constant source-to-receiver distance and with the plane of the source oriented to pass through the receiver station. In one procedure, called the in-line method, source and receiver travel in tandem along the same line. In the other procedure, called the broadside method, source and receiver move along adjacent lines, with the source-to-receiver direction oriented parallel to the assumed strike direction. The data recorded in either case are the inclinations, measured in degrees from the horizontal, of the magnetic field created by the source. These data are plotted at the receiver stations on a map. Scale-model studies of both methods of operation have been conducted in the laboratory and are reported in this paper. APPARATUS Small source and receiving coils wound with many turns of fine copper wire were used to produce and measure an alternating magnetic field in the same manner as the field apparatus. The model source coil was mounted in a vertical position and oriented so that the receiving coil was in the plane of the source. The receiving coil was mounted in a frame so it could be rotated to obtain the inclination measurements. The source coil was excited by a 100-kc signal generator. A tuned amplifier and a voltmeter were used to detect the null position of the receiving coil. The coils used in the field apparatus are usually spaced about 400 ft. The coils used in the model work were spaced from 4 in. to 4 ft apart. Thus the scale of the model work ranges between 1/1200 to 1/100 natural size. The model conductors were aluminum-coated building paper supported on wooden frames. The conductivity-thickness product was measured using a four-electrode system and was found to be about 300 ohms-'. CONDUCTIVITY CONSIDERATIONS The electromagnetic response from a thin sheet conductor is a function of the product of the conductivity of the sheet times the thickness of the sheet times the frequency of the alternating electromagnetic field times some linear dimension of the system such as the coil separation which indicates scale. The secondary electromagnetic field produced by the conductor increases in amplitude from zero at zero conductivity to a maximum value for infinite conductivity, while the phase of the secondary field with respect to the primary field shifts from 90" at zero conductivity to 0" at infinite conductivity. Several authors2-' have shown that most of both the increase in amplitude and the change in phase of the secondary field takes place over a three-decade range of the conductivity-thickness-frequency product. Only small changes in the amplitude and

Jan 1, 1961

By S. K. Tarby, W. O. Philbrook

The rate of FeO and MnO reduction from silicate and aluminate slags by carbon-saturated iron is dependent on both slag composition and temperature. Owing to variable stirring rules during- the course of reaction, the reduction processes occur in two stages in stationary graphite crucibles. In the first stage the slirring caused by CO evolution results in forced convection conditions in the slag. As the boiling action subsides during reduction, the flow conditions within the system become those defined by natural convection. Analysis of the data by an unsteady-state penetration model indicates that the rate of reduction is controlled by the rate of cocur-rent flow of' cations and anions from the bulk slag to the interface during both stages of reduction. The hearth reactions of the blast furnace have been extensively investigated from the viewpoint of equilibrium by deductions from controlled laboratory experiments. However, the literature contains relatively few studies that have been directed toward the area of slag-metal reaction kinetics, and the majority of these have been concerned with the rate and mechanism of sulfur transfer between iron and slag. More recently, attention has turned to the kinetic factors in the reduction of oxides from liquid slags. One of the first investigations in this field was conducted by Dancy1 on the reduction of pure liquid FeO and pure liquid Fe3O4 by carbon-saturated iron. The integrated form of the rate equation indicated that the reduction of FeO was of the first order up to 80 pct reduction. Over the initial 30 pct of reduction, the magnetite reaction was also interpreted as a first-order process. The rates of reaction were extremely rapid as indicated by a 30 pct reduction of the liquid magnetite in a time interval of about 1 to 2 sec. Phil-brook and irkbbride' studied the reduction of FeO from a lime-alumina-silica slag by carbon-saturated iron and solid graphite in stationary crucible assemblies. With the use of the differential form of the rate equation, the rate of the reduction reaction was found to be proportional to the second power of the concentration of the reactant FeO for both the slag-metal and slag-graphite reactions. These authors presented a number of comments in an effort to explain the difference between the molecularity of the above reaction and the observed second-order relation. One such argument, recently extended by Wagner,3 was that the rate-limiting step may well be one of transport control. A complete discussion of the proposed mass-transport control mechanism of this reduction reaction will be presented in a later section of this paper. Kinetic studies of the reduction of other oxide species, namely chromous oxide, titania, and silica, have also been reported. McCoy and philbrook4 used rotating crucible assemblies to investigate chromium reduction from Ca0-SiO2-A12O3 slags. First-order kinetic law was obeyed for the slag-metal reduction reaction as determined by the integration method of data analysis. Due to scatter of the data, any dependence of the rate constant on temperature or slag composition was obscured. Concentration-time data for the reduction of titania from blast-furnace type slags under reducing conditions were obtained by Delve, Meyer, and Lander.' The data were too few, however, for a formal kinetic interpretation. Kinetic data for the very slow reaction of silica reduction have been observed by McCoy and Philbrook6 and Fulton and chipman.7 The former experimenters found the reaction-rate constant for silica reduction by carbon-saturated iron to be 20 to 60 times less than the rate constant for chromium reduction. In their work on the reduction of SiO2 in mechanically stirred systems, Fulton and Chipman also found small values for the specific reaction rate and derived a high value for the energy of activation for the reaction. In both of these investigations, the reduction process was assumed to follow first-order behavior. schuhmann8 proposed that the rate-limiting step in this reaction is the diffusion of oxygen from the interface through a boundary-layer film to the bulk metal phase, and Rawling and Elliott9 have reported experimental confirmation of this hypothesis for temperatures below 1600°C. Turkdogan et a1.10 have also concluded that the rate of reduction of silica is a slow process and controlled by the diffusion of oxygen in the metal, but only in the absence of carbon monoxide bubbles at the slag-metal interface. In the presence of bubbles, achieved either by injecting carbon monoxide at the slag-metal interface or by blowing it through the metal and slag, these investigators found a rather rapid reduction of silica which appeared to be controlled by an interfacial reaction involving the de-sorption of silicate ions from the slag-metal interface to the metal phase as silicon and oxygen atoms. In view of the unresolved nature of the kinetics of FeO reduction and the lack of kinetic data for the manganese reaction,

Jan 1, 1968

By Herbert H. Uhlig

Although the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldla summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.I5 per cent carbon. He noted: From these comparisons it wil! be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable.lb His data showed that alloys containing 4 to 10 per cent manganese water-quenched from Iooo°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 87o°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loring2 reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 54o°C. (Iooo°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to &apos; 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.I5 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <o.ooI per cent P). In this paper it is shown that of the low-carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from IOOO°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By Herbert H. Uhlig

Although the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldla summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.I5 per cent carbon. He noted: From these comparisons it wil! be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable.lb His data showed that alloys containing 4 to 10 per cent manganese water-quenched from Iooo°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 87o°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loring2 reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 54o°C. (Iooo°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to &apos; 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.I5 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <o.ooI per cent P). In this paper it is shown that of the low-carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from IOOO°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By T. E. Eagan, W. R. McCrackin

IN dealing with segregation in babbitt, and its effect on the final cast structure, which is a bearing, it is obviously impossible to cover all of the compositions manufactured. Each composition, of course, will exhibit certain specific types of segregation. However, as examples,, two compositions of babbitt are presented: one a tin-base of well-known analysis and the other a lead-base, which in the past few years has found wide usage. Bearings usually are cast either statically or centrifugally; therefore the effect of these two methods on segregation is presented. EXPERIMENTAL PROCEDURE A slab of babbitt 1/2 in. thick by 5 in. wide and 17 in. long was cast, using a book mold with the long edge vertical. An A.S.T.M. grade 2 babbitt was used (3.5 per cent copper, 7.5 per cent antimony, remainder tin), to which 0.10 per cent tellurium had been added. Unfortunately, no metal without tellurium was available. The mold to hold the babbitt was heated to approximately 300°F., the temperature being judged by the babbitter. The pouring temperature of the babbitt was 875°F. (470°C.). One slab was made by allowing the babbitt to cool without stirring. The other slab was stirred during the entire cooling cycle. This stirring consisted of a vigorous churning or puddling into the mold until complete solidification had taken place. Three samples were removed from these slabs. One was taken at the extreme bottom, another half way to the top, and another at the extreme top, all at the center of the width. Chemical, macroscopic and microscopic examination was made of all samples. Table I shows the chemical analyses obtained at the described positions [ ] in the slab. The analyses show no serious amount of gravity segregation. Microscopic examination from edge to edge of the slab showed little change in structure. From top to bottom there was a progressive coarsening of the grain size in the stirred slab but little change in the slab that was not stirred (Fig. I). No definite exhibit of segregation could be detected. In line with our experimental study on the tin-base babbitts, we cast an almost duplicate slab using A.S.T.M. Alloy No. 15, containing 0.9 to 1.25 per cent tin, 14.75 to 15.5. per cent antimony, 0.80 to 1.25 per cent arsenic and 0.4 per cent copper. The slab was 16 in. long and 3/8 in. thick, cast with the long side vertical. One slab was allowed to cool normally and the other was stirred continually during cooling. The pouring temperature of the babbitt was

Jan 1, 1944