Search Documents

The Sub-committee on Coal Mining, since its appointment, has been collecting data about subsidences in coal mines in this country, and thinks that almost all of the available data about occurrences of this sort in bituminous mines has been collected. Similar data is being compiled for the anthracite regions, which it is hoped will be ready for the 1927 meeting. As most of the bituminous seams are nearly level, the records obtained give the problem in its simplest form, without complications due to the pitch of the seam. Copies of the questionnaire, Appendix A, were mailed to all of the coal operators' associations, to most of the large operating companies and to many engineers, with the request that any data on the subject be returned to the committee, or that advice of any subsidences known be given: the replies to most of the questionnaires were general, although some specific cases were given. Many of the companies were unable to reply to all questions, as they lacked the necessary data, but in nearly every case where accuratc data was available, it was cheerfully furnished, and any additional information requested was secured. All specific cases of subsidence were followed up by correspondence, and in several cases by personal inspection. Figs. 1 to 31 were made from the information furnished. Table 1 gives measurements of elevations taken in one case at intervals from October, 1913, to May, 1918. With one exception, where the evidence cannot be released on account of a lawsuit, it is believed that the cases submitted with this report include practically all that have happened in bituminous coal mining in this country of which actual measurements were secured. Some of these have been published by Young and Stoek,l and some have been secured from other publications. In collecting these data, the subcommittee had the Engineering Societies Library extend its bibliography to date; this list is given in Appendix B. To assist in the study of the problem, all of the subsidence literature in English was examined for cases in which spccific measurements were given, and the essential data for each case are shown in Appendix C.

Jan 1, 1927

By Y. C. Liu, W. R. Hibbard

Based on pole figure data and microstructural observations, the re-crystallization orientation found in a copper strip previously cold-rolled 99.5 pct from a single crystal with an initial (110) [112] orientation may be described as: a 30° rotation, clockwise and counterclockwise, about octahedral poles of the cold-rolled texture such that all four poles function at a low annealing temperature (400°C) and only three of them function at high temperatures (500' to 1050°C). The relative intensity of deformation stresses on various slip planes can be correlated with the choice of poles affecting the rotations found in the recrystallized orientations. ROTATIONAL reorientation about the poles of densely packed crystallographic planes is an important characteristic of secondary recrystallization" in face-centered cubic metals. Some evidence has also been interpreted to show that such a rotational relationship also exists in the primary recrys-tallization process." In an investigation of the crystallographic relationships in the recrystallization process, several aspects of the experimental procedure should be considered. With cold-rolled poly-crystalline metal as the initial material, pole figure analysis leaves many ambiguities as to whether or not simple indices can be assigned to adequately represent its orientation. The rolling texture does not consist of a single texture. Minor deformation textures are usually present. In all cases, twin textures are present. The presence of both minor and twin deformation textures influences the recrystallization texture. In order to study the recrystallization mechanism, a more precise knowledge of the history of the material before recrystallization is necessary. Tensile deformation of a single crystal usually produces residual stresses which are concentrated at slip bands. Since the exact nature and orientation of these potential nuclei sites cannot be experimentally evaluated, the tensile deformation of a single crystal was not considered adequate. From the work done by Barrett and Steadman6 n copper, it appeared that cold rolling of a single-crystal specimen with an initial (110) [112] orientation would yield a specimen which fulfills the conditions required for the present investigation, namely a highly preferred single rolling texture with relatively homogeneous stress distribution. By investigating the recrystallization texture of this material, additional details of reorientation during recrystallization might be obtained. The purpose of this paper is to describe such an investigation. Experimental Procedure Copper used in the present investigation was cathode sheet with a purity of 99.94 to 99.97 pct. A copper single-crystal specimen, 1.15x0.8720x0.5322 in. (thickness) was cut from a cylindrical crystal which was grown in a Bridgman furnace.' The cutting was accomplished on a horizontal milling machine operated at a very slow speed to obtain a (110) plane in the rolling plane and a [112] direction in the rolling direction. The disturbed surface was removed by electrolytic polishing in dilute orthophos-phoric acid (H3PO4) with a specific gravity of 1.14, and a current density of about 1 to 2 amp per sq cm. A 3-min polishing was needed to eliminate the disturbed surface causing Debye-Scherrer rings and a 45-min polish produced a surface which yielded sharp rounded Laue spots. It was estimated that about 1/16 in. of metal was removed from the original cut surface. The final orientation of this specimen before rolling was about 2" from the (110) plane in the rolling plane with a [112] direction aligned in the rolling direction. It is possible that a small amount of strain was still present in the cube despite the fact that the Laue spots seemed very sharp. It is doubtful, however, that this would be an important factor after a subsequent rolling reduction of 99.5 pct. This copper specimen was rolled on a laboratory rolling mill with two highly polished rolls 37/8 in. in diam in the following manner: 0.010 in. per pass to 50 pct reduction, 0.005 in. to 70 pct, 0.002 in. to 85 pct and, finally, 0.001 in. per pass to a 99.5 pct reduction. Specimens, about 1 in. sq with the rolling edges intact, were cut from the rolled strip by the electrolytic method previously described, after the strip

Jan 1, 1954

By L. Seigle, R. Resnick

An inert-marker movement experiment indicates that the ratio of the intrinsic diffusion coefficients DC:DTa = 80:l in TaC at 2500°C. Measurements of the diffmion coefficient of carbon in nonstoichiometric TaC at temperatures from 1700° to 2700°C reveal that Dc increases with decreasing carbon content, but much less than expected from the probable change in vacancy concentration with carbon content. A diffusion process involving two simultaneously operating mechanisms is postulated, and shown to be theoretically feasible. The average value of the carbon diffusion coefficient is given by DC = 0.18 exp[(-85,000 ± 3000)/RT] sq cm per sec over the composition range 46 to 49.5 at. pct C. BECAUSE of their high melting points and hardness, the carbides of the IV, V, and VI group transition metals, along with those of uranium, have attracted considerable interest for applications at high temperatures. In these applications the reactivity of the materials is important, and, since rates of diffusion within the compounds influence reactivity, a knowledge of diffusion kinetics and mechanisms is desirable. While many investigations of the mechanical and electrical properties of these compounds have been made, only two fundamental investigations of diffusion in the carbides are known. Chubb, Getz, and Townleyl measured the diffusivity of carbon and uranium in UC, and Gel'd and Liubimov2 measured the diffusivity of carbon and niobium in NbC. This paper describes an investigation of the diffusion of carbon in tantalum monocarbide and, in particular, the influence of carbon deficiency on this process. Tantalum carbide melts at approximately 3800°C, which makes it one of the highest melting materials known. The compound exists over a rather wide range of carbon Content.3-7 At the peritectic temperature, 3240°C, the phase extends from about 36 to 50 at. pct C. Although the compound can exist with a substantial carbon deficiency, the high carbon phase boundary remains near the stoichiometric composition over the entire temperature range; i.e., no carbon excess is observed. The structure of TaC is the NaCl type wherein carbon atoms normally occupy the octahedral sites in a somewhat expanded fcc lattice of tantalum. Decrease of the lattice parameter with decreasing carbon suggests that the removal of carbon introduces octahedral vacancies into the lattice. I) EXPERIMENTAL DETAILS AND RESULTS Inert-Marker Experiments. In a compound such as TaC the interstitial element would be expected to diffuse more rapidly than the metal. This was confirmed by an inert-marker experiment, following Srnigelskas and irkeendall.8 Ideally, the markers should be placed at the interface between a slab of low-carbon TaC and graphite, and their movement during subsequent inter-diffusion measured. Unfortunately, no solid could be found which is unreactive in contact with carbon at the high temperatures employed in these experiments. In order to circumvent this problem, a specimen was designed in which the markers consisted of several small canals running just below the surface of a tantalum slab. This specimen was prepared by machining grooves on the surface of the tantalum slab and then diffusion-bonding a thin plate of tantalum to the slab over the grooves. The surface of the plate was then ground down until the distance between the canals and surface was as small as possible (about 0.01 cm). Thus, the canals would lie entirely within the TaC phase after a short period of diffusion. The diffusion anneal consisted of immersing the metal sample in high-purity graphite powder and heating for approximately 10 hr at 2500°C under vacuum. At this temperature, the vapor pressure is sufficiently high and the transfer of carbon from graphite sufficiently rapid to allow the surface of the diffusion sample to attain the stoichiometric carbon concentration very quickly. Conclusions regarding the relative diffusion rates of carbon and tantalum in the compound layers (TaC and Ta2C) can be drawn from the location of the canals after the diffusion anneals. If the growth of the layers is governed mainly by the diffusion of carbon, as expected, the canals should remain close to the sample surface. If the diffusion of tantalum contributes appreciably to formation of the compound layers, the distance from the markers (canals) to the surface should increase. Fig. 1 shows, diagrammatically, the appearance of the specimens after diffusion, and Table I presents the depth below the surface at which the

Jan 1, 1967

By P. Chiotti, J. T. Mason

Thermal, X-ray, metallographic, and resistivity data were obtained to establish the phase diagram for the Yb-Zn system. Six intermetallic compounds and five eutectics have been identified. The compounds position at 695°C. No evidence for the compound YbZn,, was observed. Whether this compound is stabilized or inhibited by small amounts of impurities is uncertain. SEVERAL aspects of the Yb-Zn system have been reported in the literature. Much of this work deals with the crystallographic identification of some of the compounds. The YbZn compound has been reported by Iandelli and palenzonal and the YbZn, structure and thermal data for the composition range between YbZn and Yb3Znll have been reported by Michel et al. A compound of uncertain stoichiometry in the range 60 to 68 wt pct Zn with a cubic structure has been reported by Kuz'ma et aL4 The YbzZn17, YbZn,,, and YbZn13 compounds have been reported by both Kuz'ma et a1 and Iandelli and Palenzona.' YbnZn17 has also been identified by Laube. This investigation was undertaken to establish the phase diagram of this system. Ytterbium in many respects behaves as an alkaline earth rather than a rare earth metal6 and it is of interest to note the resemblance between the Yb-Zn system, the Ca-Zn,' and typical rare earth-zinc systems.g'10 MATERIALS AND EXPERIMENTAL PROCEDURES The materials used in this investigation were Ames Laboratory ytterbium and Bunker-Hill slab zinc, 99.99 pct pure. Analyses of the ytterbium showed 38 ppm Ta, 82 ppm 0, and 15 ppm N with Ca, Cu, C, Mg, Al, Si, Cr, Fe, Ni, Sc, Y, Er, Tm, and Lu all less than 50 ppm. The ytterbium was dehydrogenated by heating in tantalum under vacuum for 8 hr at 900°C. The metal was kept under argon except when being cut with shears and when being weighed. Tantalum was found to be a suitable container for alloys in the composition range between ytterbium and Yb2Zn17. With higher zinc concentrations the tantalum was penetrated by the alloy and failed after several days at temperatures of 600" to 700°C. Approximately 20 g of zinc and ytterbium metal were sealed under argon in *-in.-diam tantalum cruci- bles equipped with thermocouple wells. The crucibles were in turn sealed in stainless-steel jackets. The alloys were equilibrated in an oscillating furnace and given various heat treatments in a soaking furnace. The steel jackets were removed and differential thermal analysis data were obtained under an atmosphere of argon. The thermal analysis apparatus was calibrated against the melting points of pure zinc, aluminum, silver, and copper and found to give thermal arrests within 1°C of the accepted melting temperatures for these elements. The thermal analysis apparatus has been described in an earlier paper.g Alloys were further heat-treated as necessary and subjected to metallographic examination and X-ray diffraction analysis. Most alloys were etched with Nital (0.5 to 10 pct nitric acid in alcohol). EXPERIMENTAL RESULTS The results of the thermal analysis are summarized by the points on the phase diagram, Fig. 1. Six compounds and five eutectics were observed. The eutectic temperature and compositions in weight percent zinc are 491°C and 12 pct, 645°C and 32 pct, 687°C and 54 pct, 742°C and 67 pct, and 750°C and 77 pct. The compounds YbZn, YbZn2, Yb2Zng, Yb2Zn17, and YbZnll melt congruently at 650°, 751°, 75Z°, 754", and 755"C, respectively. The compound Yb3Znll undergoes a peritectic decomposition at 695°C. The transformation and melting temperatures for the ytterbium were observed to be 797" and 817°C. re-

Jan 1, 1969

By F. D. Wright

Production of a coal preparation plant is governed by many restrictions, such as the tonnage of different products and blends that can be sold within a given period, capacities and output proportions of the cleaning and sizing units, blending proportions, quality specifications, and costs and prices for the various products. Determination of the tonnage of each product and blend that should be made in order to obtain the maximum profit can be difficult unless a systematic method such as linear programming is used. In this paper the basic method of linear programming is described briefly. The Old Ben No. 9 preparation plant is used as an example to illustrate in detail how eqwations can be written to form a linear programming model of a coal preparation plant. Three sample problems, each requiring 56 or more equations and 63 structural variables, were solved with an IBM 650 computer. Linear programming is one of several mathematical tools used for operations research. It has been applied to many fields and has been used by a number of industries either to maximize the profits of certain operations or to minimize costs. P. B. Nalle and L. W. weeks' have described the use of the method by the Riverside Cement Co. to minimize the cost of blending raw materials to make portland cement. Their problem is to obtain at minimum cost a mix with certain specifications from a number of possible materials which have various costs and various amounts of CaO, SiO2, Fe2O3, and other constituents. In a paper on the use of linear programming by the National Coal Board in England, K. B. Williams and K. B. Halley2 describe how the transportation method, a variation of linear programming, is used to minimize the cost of sending 37 grades of coal from 28 mines to seven central washing plants which produce coal for furnace coke and foundry coke. The various coals have different percentages of volatile matter, moisture, sulfur, ash, and phosphorous, so there is considerable choice in how they can be blended to meet the specifications of the two products. The purpose of this paper is to show how linear programming can be used to maximize the profits of a coal washing plant which produces individual final products as well as blends. The Old Ben Corp. furnished assumed sample data from their Old Ben Mine No. 9 preparation plant for this investigation. However, the data that have been used are entirely the author's responsibility. METHOD OF LINEAR PROGRAMMING Numerous articles and books have been written on the theory and applications of linear programming.3-5 However, since the method has not been widely applied by the mining industry, a brief, nontheo-retical discussion of its basic method seems to be in order. Linear programming (Table I) is used to determine the best possible solution to a number of interdependent activities. It is essentially a method for making systematic selections from a number of possible solutions to determine positively the optimum solution. There may be other equally good solutions but no better ones. Each activity must have linear coefficients and there must be a criterion to judge how good the solution actually is. Linear programming is different from the solution

Jan 1, 1961

By E. C. Tveter, L. A. Roe

The authors present a general outline of the theory and development of heavy-liquid application to mineral processing. Patent literature and processes are reviewed with special emphasis on liquid recovery systems which have been employed or proposed. Advantages and disadvantages of the process are discussed together with the recent developments which have revived interest in this old concentration method. The most important single factor in this resurgence of interest is concluded to be the narrowing gulf between chemical engineering and mineral dressing which has opened the field for new concepts of mineral plant design. A partial summary of patents on heavy liquid separations is included. In spite of the fact that heavy-liquid separation with organic liquids has been used in the laboratory for over 50 years, this process has never graduated to large scale commercial use for any extended period. However, a variation of this process, the sink-float or heavy-media separation process has found wide acceptance and is used to separate minerals from diamonds to gravel. Materials used to increase the specific gravity of the pulps used as heavy media include sand, clay, barite, magnetite, galena, hematite, atomized lead and ferrosilicon. Because of the greater ease of recovery, the magnetic materials, magnetite and ferrosilicon, are the preferred media today. In the U. S. alone, heavy-media iron ore plants with a capacity of over 10 million tons of concentrate per year are in existence. Heavy-media separation involving use of solid, inorganic particles suspended in water rapidly found a wide range of commercial use with the introduction of magnetic media. The minerals engineer is experienced in working with suspensions and quickly learned to develop and control such media at a cost compatible to the type of separation desired. The natural superiority of a heavy liquid with uniform chemical and physical properties has never been questioned since its first use in laboratory mineral separatory procedures. It offers the only method for gravity separation of fine particles of relatively close specific gravity. The most important early attempt to make heavy liquid separations commercial were made by the DuPont Co. which began experimental work on Virginia limonite in 1904. The appended "Partial Summary of Patents" compiled by W.L. O'Connell of The Dow Chemical Co. demonstrates the quantity and sequence of this work. Both inorganic and organic parting liquids were investigated and numerous patents were issued on the use and recovery of these liquids. The work culminated in the heavy liquid plant of the Weston Coal Co. at Shenandoah, Pa. Chemical engineering design of this plant was the responsibility of Francis I. and Hubert I. DuPont. Heavy-liquid separation of coal almost achieved commercial status at this plant which actually processed over 20,000 tons of coal. The liquids used were tetrabromethane, pentachloroethane and trichlo-roethylene, with liquid losses ranging from 8.9 to 12.4 oz per ton of cleaned coal. The reasons for failure of this plant are not clear but probably involved toxicity problems as well as other problems in chemical engineering. Excellent economics were reported. A more recent pilot plant was built in 1954-55 by Norris Goodwin for the Inerto Co. to treat hectorite clay. This plant employed carbon tetrachloride in jigs with liquid recovery by evaporation. Although good separation was achieved, incomplete removal of the CCl, from the clay prevented commercial operation. The only present operations known to the authors employing heavy liquids for gravity separations are limited to the use of calcium chloride in certain coal washers and bromochloromethane in a small batch operation (one ton solids per day) for the separation of beryllium metal particles from slag materials. This is not strictly a minerals beneficiation problem but it has demonstrated the feasibility of such separations. PROBLEMS Critics of early attempts to commercialize heavy-liquid separation of minerals summarize the draw-

Jan 1, 1963

By Charles W. Dickson

CONTENTS. [ ] I.THE RELATION OF NICKEL TO PYRRHOTITE. Introduction. The Sudbury district is to-day one of the two great sources of nickel in the world. The peculiar geological relations of

Jan 1, 1913

By J. E. Burke, C. S. Barrett

The fine lines shown in Fig I are typical of markings that ma): be detected after polishing and etching deformed specimens of alpha brass and other alloys. Although they have long been the subject of discussion by metallurgists their nature is still uncertain and the names that have been applied: to them, such as deformation line4 or strain markinas, indicate this uncertainky. In this paper which repotts the results of a furthcr investigatinn of their nature, they will be called strain mxrkings. Introduction Mathewson and Phillips1 described strain markinps in 1 916 and concluded that they appear only after 20 pet deformation. They objected to the markings being called slip tines believing this term should be sewrved for surface markings protluced by plastic deformntion. In 1921. vogel² described similar striations which appeared after polishing and etching the roughly ground surface of numerous alloys. He reported that the markings were crystallo-graphic in nature, and since they resemble Seumann hands in iron, at least superficially, he assumed them to be mechanical twins. In 1928, Matherwson reported work by Phillips which indicated that the lines were more readily produced by impact than by slow deformation and that in many cases the twins inside recrystallized grains were parallel to strain markings in the original deformed grains. This was taken as cvirlence that the markings coalesce into anncaling twins. and hence that they themselves are mechanical twins. Many attempts have been made to demonstrate directly that the markings are mechanical twins. In 1934, Samans described the results of X ray studies of two defomed crystals of alpha brass. Evidence was obtained which could be interpreted to indicate that the strain markings arc mechanical twins, and this remains the only direct evidence to this effect. Several other attempts to obtain similar evidence by X ray diffraction have failed5.8.7 although in no Ease was the original method of Samans employed. An

Jan 1, 1949

By C. S. Barrett, J. E. Burke

The fine lines shown in Fig I are typical of markings that ma): be detected after polishing and etching deformed specimens of alpha brass and other alloys. Although they have long been the subject of discussion by metallurgists their nature is still uncertain and the names that have been applied: to them, such as deformation line4 or strain markinas, indicate this uncertainky. In this paper which repotts the results of a furthcr investigatinn of their nature, they will be called strain mxrkings. Introduction Mathewson and Phillips1 described strain markinps in 1 916 and concluded that they appear only after 20 pet deformation. They objected to the markings being called slip tines believing this term should be sewrved for surface markings protluced by plastic deformntion. In 1921. vogel² described similar striations which appeared after polishing and etching the roughly ground surface of numerous alloys. He reported that the markings were crystallo-graphic in nature, and since they resemble Seumann hands in iron, at least superficially, he assumed them to be mechanical twins. In 1928, Matherwson reported work by Phillips which indicated that the lines were more readily produced by impact than by slow deformation and that in many cases the twins inside recrystallized grains were parallel to strain markings in the original deformed grains. This was taken as cvirlence that the markings coalesce into anncaling twins. and hence that they themselves are mechanical twins. Many attempts have been made to demonstrate directly that the markings are mechanical twins. In 1934, Samans described the results of X ray studies of two defomed crystals of alpha brass. Evidence was obtained which could be interpreted to indicate that the strain markings arc mechanical twins, and this remains the only direct evidence to this effect. Several other attempts to obtain similar evidence by X ray diffraction have failed5.8.7 although in no Ease was the original method of Samans employed. An

Jan 1, 1949

By P. J. Carroll, H. Colijn

Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. Feeder load, material properties, feed rate, physical layout, and environment as well as first cost determine the selection of feeder type. This paper provides a new method of calculating feeder loads with some experimental data as verification. General design criteria for belt and apron feeder, rotary table and plow feeders are discussed and a special section is devoted to vibratory feeders. Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. During the past few years various papers have been written and presented on feeders and their application.1-9 This paper will be confined to some specific bin-feeder design criteria such as feeder load and power requirements. Special attention is given to the basic design criteria for vibratory feeders. HOPPER AND BIN DESIGN Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. A lot of effort has been devoted in the past decade to the development of functional design criteria for hoppers and bins.1,10 The integrated concept of bin and feeder design requires quantitative analysis of the bulk material characteristics before the design and the selection of components can be attempted. The design of a feeder system must begin with the proper dimensioning of the hopper outlet to prevent arching or ratholing. The hopper opening should be large enough to allow passage of the bulk solid at the required maximum discharge rate." A feeder can only throttle the flow. FEEDER LOAD DETERMINATION Over the past ten years, there have been various attempts to determine the exact load or pressure on feeders mounted directly under hopper openings. Many designers, however, still consider this pressure equal to the hydrostatic head of material above the opening, and because such pressure would be very

Jan 1, 1969

By H. M. Howe

PART I. INTRODUCTORY. § 24. INTRODUCTION.-This paper discusses the chief existing data as to the temperature, in iron-carbon alloys, of Ae.3, the upper limit of the transformation range when in equilibrium, as distinguished from Ac3, the temperature at which the end of the transformation is noted in heating up, and from Ar3, that at which its beginning is noted in cooling down. The former is in fact carried above Ae3 and the latter below Ae3 by lag. I touch incidentally on the influence of manganese on Ae3 (§ 29, p. 1102). The sections, tables, and illustrations, are numbered consecutively with those in the accompanying papers by Howe and Levy on Determination of, the Position of Ae3 in Carbon-Iron Alloys, and by Burgess, Crowe, and Rawdon on Thermal and Microscopical Examination of Professor Howe's Standard Commercial Steels, to which the present paper forms a sequel. § 25. The contradictoriness of our present evidence is shown by grouping it together in Fig. 14. For instance, both Goerens and Meyer (Series 2) and Meuthen (Series 12) used practically stationary temperature, and thus reduced the influence of lag very greatly; yet Ae3 for 0.32 carbon steel according to the former investigators is 894°, but according to Meuthen it is at or below 770°, a discrepancy of 124° or more. In view of our ability to measure these high temperatures within a few degrees, the existence of such a discrepancy is as unwelcome as it seems needless. I attack the thankless task of bringing some order out of this chaos.

Jan 6, 1913

By R. Woodward Moore

A GRAPHICAL method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application.

Jan 1, 1944

By Pol Duwez, Ellis P. Frink, Paul Pietrokowsky

Ti-Au alloys in the composition interval 0 to 66 213 atomic pct Au have been studied over a temperature range from 400° to 1500°C. A partial phase diagram has been established from micrographic and macroscopic observations. All intermediate phases, Ti3Au, TiAu, and TiAu., exhibit open melting maxima. It has been observed that small additions of gold lower the allotropic transformation temperature of titanium. The P solid solution decomposes eutectoidally to a solid solution plus Ti3Au. The solubility of gold in a solid solution decreases with temperature. THERE have been several papers in the literature pertaining to the alloy system Ti-Au. However, a comprehensive study of this interesting constitu- tion diagram has not been conducted. Previous investigations have been concerned with the crystal structure of intermediate phases or partial phase diagrams. This paper represents a partial constitution diagram, Ti-TiAu,, the first portion of an investigation of the entire binary system. Laves and Wallbaum' reported the intermediate phase Ti,Au to be isomorphous with CuAu, L12 type. In a more recent paper, Duwez and Jordan' have concluded that TiAu has an atomic arrangement which is related to Cr,Si. The intermediate phase

Jan 1, 1957

By A. T. Goldbeck

THE use of stone as a building material in relatively large blocks is recorded in ancient historical records but only within the past 200 years has broken stone in small sizes begun to have extensive use, principally in highway construction. Tresaguet, in 1764, describing his method for highway construction in France, required the top surface to be built of stone about the size of a walnut, broken by the use of a hammer. It is said that the Romans, in the top layer of their rather massive roads, used large stones bonded together with lime mortar and bedded in small stones mixed with mortar. Much of the early macadam as built by McAdam around 1815 in England was made with hand-sledged broken stone. In 1858, the use of crushed or broken stone received a great impetus from the invention in that year by Eli Whitney Blake of what is said to be the world's first stone crusher. As a consequence of that invention, stone could be crushed to small sizes with considerable ease and, as a natural result, the use of crushed stone in macadam roads and as railroad ballast increased at a great rate. Also, as portland cement came into use, machine-produced crushed stone furnished readily available aggregate. Rapidly, other uses developed, such as for fluxstone in the production of pig iron and for other metallurgical operations and chemical utilizations. These utilizations made for the rapid growth of the crushed-stone industry and this growth is still proceeding with the growth of population and the development of new uses, notably the employment of limestone for the improvement of soils for agricultural purposes. The industries of which the production of crushed stone is a part have a tonnage second only to that of mineral fuel in the mineral industries of this country.

Jan 1, 1949

By K. D. Sheffler, R. W. Hertzberg, R. W. Kraft

The Ni-Ni,Ti lamellar eutectic alloy responds to unidirectional solidification by alig-nment of the platelets of the two phases roilghly perpendicular to the moving solid-liquid interface. X-ray diffraction and zetallographic experimenls show that the following cryslallographic relationships exist in the directionally solidified ingots: lamellar interface w [0001] Ni3Ti 11 (111 }Ni local growth direction (1120) Ni3Ti n (110) Ni These relationships are rationalized on the basis of the crystallography of the constituent phases. In recent years researchers in several laboratories have shown that an aligned or "controlled" micro-structure can be produced in many binary eutectic alloys by forcing the alloy to solidify unidirectionally in an elongated crucible.'-3 It also has been found that a unique crystallographic relationship often develops between the two phases in such a structure.4, 5 Since a parallel arrangement of phase particles in an alloy should, and, in many cases, does, produce unique and highly anisotropic properties, the alloys so produced are of potential interest in a variety of applications. Studies of these alloys are also of interest at the academic level because they help to improve our basic understanding of the way in which metals solidify. This paper reports the metallographic and crystallographic structure of another of these alloys—that between nickel and Ni3Ti. In a separate paper, hot tensile and stress rupture properties as well as deformation and fracture behavior of the same alloy are discussed.19 EXPERIMENTAL DETAILS AND RESULTS General Characteristics of the Eutectic Reaction. Several small exploratory Ni-Ti melts were made to resolve a conflict in Hansen6 over the eutectic composition. The alloy containing 16.4 at. pct Ti, Fig. 1, appeared metallographically to be closest to the eutectic composition, although small dendritic patches of proeutectic nickel are present. The eutectic morphology is lamellar and appears quite sharp and angular, indicating a strong influence of crystallographic factors upon the microstructure. Some of the eutectic nickel platelets are continuous with the primary phase, whereas in hyper eutectic melts a "halo" of nickel generally surrounded the proeutectic inter-metallic platelets, indicating that nickel is the nucleating phase in this eutectic reaction. Extensive precipitation of Ni3Ti has occurred in the primary nickel phase in a Widmanstatten pattern which makes the dendrites difficult to differentiate from the eutectic mixture. This phenomenon may account for discrepancies among the eutectic compositions reported in the literature. The sloping solvus line bounding the nickel primary solid solution explains the presence of the intermetallic precipitate. Poole and Hume-Rothery7 report that the solubility of titanium in nickel drops from 13.8 at. pct at the eutectic temperature (1304°C) to approximately 9 at. pct at 700°C (Ni3Ti, on the other hand, melts con-gruently and exhibits essentially no solubility for nickel or titanium). Lever rule calculations based upon Poole and Hume-Rothery's phase diagram indicate an increase from 21 vol pct Ni3Ti in the eutectic mixture at the eutectic temperature to 61 pct at room temperature. Selective point count measurements of the volume fraction of eutectic Ni3Ti platelets in the eutectic microstructure yielded a value of 46 i 2 vol pct, which required extensive precipitation of Ni3Ti from the nickel solid solution onto the eutectic intermetallic platelets during cooling from the solidification temperature. Influence of Directional Solidification. Nickel bar and titanium sponge of 99.9 pct purity were induction-melted in zirconia crucibles under argon in the proportion of 13.8 wt pct (16.4 at. pct) Ti to produce 14-lb master heats which were cast into investment molds yielding 5/8-in.-diam pins approximately 10 in. long. These pins were remelted under argon in horizontal zirconia boats and unidirectionally solidified to produce 1/2-in.-sq ingots approximately 44 in. long. Details of the experimental techniques and apparatus are described elsewhere.'

Jan 1, 1970

By D. D. Pollock

Many constitution diagrams do not indicate the limits oJ solid solubility of the silver-rich solid solutions below 200°C. Thermoelectric measurements were employed to determine this limit in the nieighborhood of room temperature. The appearance of a second phase causes a discontinuity to occur in the tkevtrroelectric power as a function of cornposition at constant temperature and pressure. This discontinuity was employed to determine the limits of the silver-rich terzinal solid solutions of the Ag-A l, Ag-As, Ag- Bi, Ag--Ge, Ag-In, Ag-Pb, Ag-Sb, and Ag-Sn systenls at 30°C. CONSIDERABLE work has been done on the constitution of binary alloys of silver. The available data have been compiled by Hansen1 and Elliott.2 However, many of the binary diagrams do not show the limits of solid solubility of the silver-rich solutions below about 200° C. This work was undertaken in an attempt to extend these limits to the neighborhood of room temperature . PREPARATION OF ALLOYS All of the alloys were made with silver containing less than 0.014 pct (by weight) of impurities. The materials were weighed out into 225-g heats and melted in a high-frequency induction furnace. The indium, tin, and antimony alloys were melted in A1203 crucibles, under a boric anhydride cover, and were poured into split graphite finger molds. The aluminum, germanium, arsenic, lead, and bismuth alloys were melted in machined graphite crucibles; they were also covered with boric anhydride and poured into split graphite finger molds. The $-in.-diam ingots were heated to 750°C and were forged and hot-rolled down to 0.1 by 0.1 in. The wires were pickled in a 25 pct HNO3-75 pct H2O solution to remove any oxygen-rich surfaces. The wires were then annealed at 550°C for 2 hr in a dissociated ammonia atmosphere. They were then furnace-cooled for 20 hr to room temperature in this atmosphere. The wires were cold-drawn to 0.0808 in. diam. The finished wires were again annealed at 550°C in the same manner as in the first anneal. Thermoelectric Power. The thermoelectric power of a single specimen of each alloy was determined against pure silver which contained a maximum impurity content of 0.014 pct by weight. The wire specimens were straightened and then cleaned with ethyl alcohol. They were then reannealed in the same way as the finished wires to assure that any residual stress would be at a minimum level. Previous work has shown that the presence of small amounts of stress has the effect of decreasing the thermoelectric power. The alloy specimen was soldered to the pure silver wire to form the measuring junction. A standard set of copper leads was then soldered to the reference junctions of the thermocouple. These junctions were maintained in separate dewar flasks which contained finely shaved melting ice during the test. The thermal electromotive forces of the thermocouples were measured at four temperatures between 15° and 45°C. A known source of electromotive force was balanced against the output of the thermocouple until a null balance was reached. The data were then expressed in terms of the thermoelectric power at 30°C. The results were then converted to absolute thermoelectric power, s303.3 These data have an average error of less than ±0.2 pct. RESULTS AND DISCUSSION All of the experimental data are given in Table 11. Since the electromotive forces of the binary alloys of silver were determined against the pure silver from which they were made, the resultant thermoelectric powers are only a function of the intentionally added binary elements at the constant test temperatures. This provides a direct measure of the effects of the alloying elements. The absolute thermoelectric power of an alloy of silver is given4 by:

Jan 1, 1968

By Ralph Hayden

I. INTRODUCTION. IN the wet concentration of ores there is always a certain amount of very fine material with which to contend, and which invariably carries such quantities of value that the treatment of it is worth while; commercially. This fine material usually contains that portion of the ore which hinders the separation of the mineral values: namely, the colloidal material resulting from the decomposition of certain constituents of the ore. The object of this paper is to show what efforts have been made to solve the slime problem as it occurs in the concentrator of the Washoe

Jan 8, 1913

By G. F. Loughlin

More than 20 years have passed since the publication of Lindgren and Ransome's report on the Cripple Creek District,1 which was made when the district was much more active and prosperous than in recent years. They concluded that the output of the district, which had reached its maximum of about $18,200,000 in 1900, would gradually decline, and their conclusion has been confirmed by records of subsequent production. Between 1905 and 1915 annual declines were partly compensated by encouraging increases, especially in 1908, 1914, and 1915; but a rapid continuous decline followed, due largely to the war and its after-effect's, until in 1922 the value of output was only slightly more than $4,000,000. It rose to nearly $5,000,000 in 1924, but declined again in 1925 and in 1926, when it was about $4,400,000, and represented ores mainly from deep levels in the Cresson and Portland mines. The profitable operations of these two mines were the principal factors leading to a study of ore at deep levels in the district by the U.S. Geological Survey in cooperation with the Colorado Metal Mining Fund. The principal reasons for Lindgren and Ransome's conclusion were three: (I) the greater cost and difficulty of deep exploration; (2) the decrease in the number of veins with increasing depth, and (3) the probability that the telluride ore, believed to have formed at comparatively low temperature, would not persist indefinitely in depth. Operations since they made these statements have verified the first two, but call for some modification of the third. Rich telluride ore is being mined at a profit in the Portland mine 3000 ft. below the present surface, 07. 5000 ft. below the original surface of the Cripple Creek volcano, as interpreted by Lindgren and Ransome. The question arises, therefore, as to the number and extent of such deep deposits, and the answer, so far as it can now be given, must be based mainly on structural data, supplemented by data on the processes of ore deposition. Presentation of these data based on a study of deep mines in the southeast quarter of the district, the only

Jan 1, 1927

By J. W. Gwinn

The underground haulage system in the lead-silver mine of the Bunker Hill & Sullivan Co., situated at Kellogg, Idaho, is the most extensive in the Cæur d'Alene district, comprising about 35,000 ft. of tunnels, drifts, and cross-cuts where locomotive haulage is in use. The main working adit, known as the Kellogg tunnel, or No. 9 level, is approximately 10,000 ft. in length from the portal to the main working shaft and extends beyond that about 4,500 ft. in each of two directions. On this level all the ore from the Bunker Hill & Sullivan, the Sierra Nevada Consolidated, and the Caledonia Mining Co.—an average of 44,600 tons per month—is hauled to the mills, located a short distance from the portal. Electric haulage by the trolley-type locomotive is used on this level throughout. Below this level, at intervals of 200 ft. vertically, are five other working levels (Nos. 10, 11,12,13, and 14); and the total haulage distance on these, where electric locomotives are used, is approximately 16,000 ft. No. 13 level has but recently been opened up and is not working to capacity; while the main cross-cut on No. 14 has just been started, and has no need of power haulage. Of the four levels equipped with electric haulage, Nos. 11, 12, and 13 have storage-battery locomotives, and No. 10 still retains the trolley type by reason of the small and decreasing tonnage produced. Electrification - Electric power is supplied to the mine by two systems. The first, the 500-volt direct-current trolley, was installed in 1897 when the Kellogg tunnel was started, and was extended as the tunnel advanced, being used for the first trainload of ore on Nov. 17, 1902, since which time it has been in continuous service. The current for the line is transmitted on a No. 00 copper wire as far as the shaft, and on No. 0 wire throughout the remaining length of the Kellogg tunnel; and until the installation of the storage-battery locomotives it was used in practically all the cross-cuts and drifts on each level below No. 9.

Jan 1, 1915

By Carl Henrich

Aspen, the flourishing mountain- and mining-town of Pitkin county, Colorado, is located in the valley of the Roaring Fork, 11 miles above Glenwood springs, where that stream empties its waters into Grand river, a tributary of the Colorado. The Roaring Fork heads on the western slope of the Sawatch range near Grizzly peak, and runs in a general northwesterly direction to its junction with the Grand river. Of its numerous tributaries, Castle creek joins it just below the town of Aspen, the town being built on an extensive flat hounded on the northeast by the Roaring Fork and on the west by Castle creek. The latter heads at the junction of the Sawatch and the Elk mountains and flows northward between the two chains, until it empties into Roaring Fork. Opposite the town of Aspen, Hunter creek, coming westward from the western slope of Mount Massive, joins the Roaring Fork. About a mile north of Aspen, the bed of Hunter creek is at least 300 feet higher than that of the Roaring Fork at Aspen. Hunter creek forms thus, at its mouth, one of the best water-powers in Colorado. A portion of it is now utilized for electric lighting in Aspen, while in the near future, the whole of this magnificent natural power will be applied, through electric transmission, for hoisting, pumping and ventilating at different mines of the district. The mountain opposite the town of Aspen, on the east side of Hunter creek (which near its mouth flows southerly), is called Smuggler mountain, from the famous mine at the foot of it. On the other, or western, side of Hunter's creek (see map, Fig. I), a higher mountain rises, on the slope of which the regular dip of the Triassie or Upper Carboniferous red sandstone strata, alternating with white layers of the same rock, can be clearly seen from town. This mountain is called Red mountain, from the prevailing color of its rocky

Jan 1, 1889