Search Documents

By M. C. Young

The Ozark Lead Company operating facilities are located in Reynolds County at the south end of the "New Lead Belt" of southeast Missouri. Development of this wholly owned subsidiary of Kennecott Copper Corporation started in May 1964, with a six foot diameter by 1250 foot deep steel lined shaft. A 20-foot diameter, 1480 foot deep, concrete lined production shaft was collared in March 1968. Production from the facilities began that month and has reached a present average of approximately 6000 tons per day. This paper describes the fully automatic system used to hoist the lead-zinc ore from a depth of 1420 feet to the surface crushing and concentrating facilities, as well as the man and materials hoisting system which allows the lowering of large equipment into the mine. MINING Galena, sphalerite and some copper minerals are found in several mineralized zones of the relatively flat lying dolomite of the "Bonneterre formation". The mineable ore zones vary from 10 feet to 110 feet thick, from 200 feet to 1200 feet wide, and several thousands of feet on strike. Two-boom diesel-hydraulic jumbos equipped with rotary percussion drills are used for both development and production. The jumbos are used principally to open the room and pillar stopes, and a track mounted down hole drill is used to bench in areas where the ore thickness warrants. Explosives used are ANFO, dynamite, and water-jell which are detonated by electric blasting caps. Broken ore (and waste) is hauled by rubber tired transports to chuted transfer raises. Approximately every 500 feet, these raises connect the orebody to the 15 foot by 28 foot train haulage level below. Two twenty ton diesel-hydraulic locomotives haul 160 tons per trip to storage pockets which have a total storage of 1500 tons of material. From these pockets the material is fed over a 6 foot by 20 foot mechanical vibrating feeder which includes one 4 foot by 6 foot grizzly section to a 48 inch by 60 inch jaw crusher. The grizzly and crusher products are transferred horizontally 45 feet on a 48 inch conveyor belt, to one of two 750 ton storage pockets. The material can flow unimpeded into one pocket or be deflected into the second pocket by a movable rock filled hopper. LOADING POCKET The material in each storage pocket is controlled by six lengths of ship anchor chain. The upper end of the 20 foot chain is anchored behind a brow in the pocket, while the lower ends are joined by a header. The lower ends of the chains are raised by two electric powered marine barge winches using 3/4 inch cables. The crusher operator controls the raising and lowering of these chains from a console in the crusher station. The upper and lower travel of the chains is controlled by cams and limit switches on the winch drive. The winches are located within 5 feet of the shaft, and shaft water continually causes problems with the electric components. A malfunction in the upper travel switch will cause the winch to pull the chains into the cable sheave (breaking the cable or sheave), while the lower switch causes the winch to unwind too much rope. Serious consideration is being given to changing the electric motors to pneumatic, since pneumatic motors will eliminate the need of any electrics at the winches. The winches can be "bottomed out" against the sheave without damage to the cable or sheave when raising the chains, and can be allowed to "free wheel" to lower the chains. A surge pocket below the two storage pockets feeds material to two

Jan 1, 1975

By E. P. Mathewson

The early development of the reverberatory furnace for smelting copper-ores was the work of the Welsh smelters, particularly those of Swansea. The first record of a reverberatory furnace is made by Jars, who states that in 1755 copper-smelting was effected .in reverberatory furnaces at Middleton-Tyas, in Yorkshire, England. The first patent, of any importance, for improvements in reverberatory furnaces was granted to Thomas Williams in 1778 for the granulation of the regulus. The next was that of William Evetts, in Sheffield, in 1812, for the cooling of the fire-bridge by the admission of air. Charge-hoppers above the furnaces were in common use in 1848. The size of the hearth of the furnaces about the beginning of the 19th century was commonly 11 by 8 feet. No material development was made until the Welsh process mas brought to Colorado, where Richard Pearce, as manager of the Argo works, near Denver, developed the furnace to meet the requirements of a custom plant, under keen competition with lead-silver smelting-plants, using blast-furnaces. His improvements are outlined in Fig. 1, elaborated by permission from E. D. Peters's excellent work,' to which the reader is referred for further details. This figure shows that the furiiaces were in 1878, 9 ft. 8 in. by 15 ft. in hearth; and in 1894, 16 by 35 ft., while the capacity of the furnace had been increased from 12 tons per 24 hr. to 50 tons in the same period.

Jan 1, 1913

Sifto Salt Div. of Domtar Chemicals Ltd. has developed a new method for installing roof bolts in the high backs of its 1-million-tpy rock-salt mine at Goderich, Ontario, on the east shore of Lake Huron. The method teams a telescoping- boom hydraulic crane with a specially developed combination auger-drill and bolt-tightening ma- chine. One man, controlling all operations from a basket supported at the end of the crane's telescoping boom, installs an average of 100 5-ft roof bolts per shift, at heights to 45 ft. The mine has very long backs that are not as stable as might be expected. The result has been that roof scaling has occupied an unusually high percentage of the underground work force. About six years ago, company officials decided to go to 100% roof bolting of all backs as a safety measure. The present roof-bolting equipment is the result of a development program instituted at that time to find a faster and more economical method for doing the job.

Jan 9, 1967

[Murray and Renard: chondres on ocean floor, XLI, [155]. Musconetcong Iron Works, Stanhope, N. J., blnst furnace, XL, 467. MUSSEN, H. W.: Discussion on The Bogoslovsk Mining Estate, XXXIX, 897. death, XLIII, [Ixxvi]. Muzo, CoIombia: emerald deposits, LV, 910. emerald mine, XXXIX, 317. minerals, LV, 925.]

Jan 1, 1918

By J. B. Cheatham, C. E. Murphey

Presently, computer control of Borobolic direction cannot be obtained during drilling, and most straight-holc drilling methods attempt to resist hole deviation rather than control direction. Many of the theories advanced as possible explanations of the cause of hole deviation are Summarized berein. A new correlation of physical partables is introduced to indicate bow factors such iis drill collar stiffness clearance and hit weight influence borehole deviation, .A methord is proposed for predicting the rate of change of hole angle when drilling conditions are changed. INTRODUCTION Control of borehole direction during drilling can be difficult and costly. Unintentional crooked holes are often lrilleti in dipping formations and many times directional drilling is required when the surface location is not directly above the target area —- for example, at offshore and mountainous locations. Prilllng progress can be greatly hindered in either air or liquid drilling when it be comes necessary to use low bit weight to prevent excessive hole angle build-up. If hole inclination becomes too great, drill pipe drag becomes excessive and fishing risks are increased, logging is more difficult and problems of differential sticking, key seating and fatigue failures may be encountered. Dog-legs and key seats are more serious problems than steep inclination angles: therefore, reducing rate of direction change is preferred to attempting to maintain absolutely vertical holes. Consequently, a straight inclineti hole is preferable to a nearly vertical crooked hole containing numerous dog-legs. In this paper, theories of the cause of hole deviation and analyses of drill string behavior under down-hole conclitions are summarized. Methods for computing hole deviation are presented und systems for resisting deviation as well as neans for provic!ing control of holt- direction are iliscusseI. A new correlation of physical variables is introduced tu indicate how factors such as drill collar stiffness, clearance and bit weight influence borehole deviation. A method is oroposeti for predicting the rate of change of hole anFrle when drilling conditions are clianged. IIEVIEU' OF PREVIOUS WORK ON HOIaE DEVIATION Significant progress in the theoretical analysis of hole deviation problems has been made in the past 1 5 years. The pioneering work has been primarily a result of the efforts of Lubinski and Woods.l-5 In 1950, Lubinski 1 considered the buckling of a drill string in a straig:rt vertical hole, a problem also considered by Willers6 in 1941. It wns concluded that very low bit weights must be used to prevent hole deviation resulting from drill collar buckling. The use of conventional stabilizers was proposed2 in 1951 by Mac Donald and Lubinski as a method for permitting greater Sit weights to he carried without drill collar buckling. These authors pointed out that a 2° nearly vertical spiral hole can cause severe key seatinp, and drill pine near, wilereas n 3 straight inclined hole with deviation all in one direction, while not vertical, will not result in serious drillirig or producing problems. Studies were continued with an investigation of straight inclined holes by Lubinski and Woods3 in 1953. In this paper they concluded that perfectlv vertical holes cannot be drilled even in isotropic forriations unless extremely low bit P-eights are used. .l'l~ey postulated that constant drilling conditions produce holes of constant inclination angle and varying conditions cause the hole to drill at a neiv equilibrium angle. This analysis was not concerned with drill string buckling since it was based on an equilibrium solution in which the ~irill string Was presumed to lie along the lower side of the hole abcrve the point of tangency. Weight of the drill collars below the point of tangency tends to force the hole toyard the vertical, whereas the weight on hit tends to force the hole aurav from the vertica l. The concept of an anisotropic formation Lvas introduced as an empirical method for explaining actual drilling data and as a means for extrapolating known deviation data to otiier conditions of hit

Jan 1, 1967

By D. B. Hunter, H. W. Rosenberg

The titanium-rich portion of the Ti-Pd system was investigated from 0 to 75 wt pct Pd by metallo-graphic and X-ray techniques. A 0 eutectoid occurs at 24 wt pct Pd and 1190°F. Two compoutzds are indicated in the region below 75 wt pct Pd, Ti,Pd and Ti2Pd3. The solubility of palladium its a titanium is low, probably less than 1 pct. In 1960 Rudnitskii and Birunl published a complete version of the Ti-Pd phase diagram. However, their work was in disagreement with the earlier literature in that they reported only one inter metallic compound, whereas three had been reported earlier. In view of these discrepancies, it was therefore necessary to redetermine those portions of the diagram of immediate interest. The following account describes our work on the system over the range of 0 to 75 wt pct Pd. MATERIALS AND METHODS Distilled titanium sponge and elemental palladium were used in the formulation of the alloys; the chemistry of these materials is detailed in Table I. The alloys were prepared as 10 to 50 g blended compacts that were melted into buttons by arc melting under gettered argon on a water-cooled copper hearth. Weighing of the ingredients before and after melting showed that negligible weight changes occurred. Therefore, no analyses were undertaken and the compositions of all alloys are nominal. All alloys were fabricated by hot rolling at 1700°F to 0.070-in.-thick sheet. Scale was removed by sandblasting and pickling in a 5 pct HF-35 pct HNO,, balance H20 solution. For metallographic examination, specimens were mounted after heat treatment transverse to the rolling direction, ground on silicon carbide papers of increasing fineness to 600 grit, and then electro-polished using a solution containing 600 ml me-thanol, 60 ml perchloric acid, 360 ml butyl cello-solve, and 2 ml "Solvent X". Unless otherwise specified, etching of alloys containing up to 42 pct Pd was carried out by swabbing with a 12 pct HN03-1 pct HF aqueous etch where a bright etch was required, or by a 1 pct hydrofluoric in saturated oxalic acid solution where contrast between phases was required. The Ti-52.8 Pd alloy was etched with a solution of 25 ml HF, 40 ml glycerine, 35 ml methanol, and 18 g benzalkonium chloride. For X-ray examination, 1/2-in.-square speci- mens of sheet were mounted flat in a standard 1-in. metallographic mount and ground and polished as above. X-ray diffraction was performed using a Norelco type 12045 Diffractometer, employing CuKa radiation with a nickel filter at 40 kv and 20 ma. Specimens were rotated about the sheet normal during exposure. Although this procedure did not remove the effects of sheet texture from the relative intensities, it had the advantage that oxidation or contaminants entering during preparation of powder samples could not confuse the patterns obtained. RESULTS AND DISCUSSION Fig. 1 illustrates the Ti-Pd phase diagram according to Rudnitskii and Birunl with the work of the present authors superimposed. Both interpretations agree that the system is of the 0 -eutectoid type with an extensive 0-phase field, and that the eutectoid temperature is just below 1200°F. There is also agreement that the solubility of palladium in a titanium is restricted. Our work would indicate that the a solubility of palladium is low, probably less than 1 pct. However, whereas Rudnitskii and Birunl place the eutectoid composition at 41 wt pct Pd, this investigation shows it to be at about 24 wt pct Pd. Moreover, this investigation confirms the existence of compounds at Ti2Pd and Ti2Pd3, whereas Rudnitskii and Birun report only a single Berthol-lide phase covering the TiPd to TiPd, range. Laves et a1.' and Wallbaum, whose work was summarized by Maykuth , reported the existence of Ti2Pd3 and TiPd, in addition to Ti2Pd. More recently, Nevitt and Downe~' have reported the structure of

Jan 1, 1965

By K. Osseo-Asare

The thermodynamics of solid-aqueous solution equilibria up to 200°C In the systems Me-NH3 H2 0 (Me=Cu, Ni, Co) are summarized with predominance area diagrams generated with the DIAGRAM computer program. The implications of the diagrams to ammonia hydrometallurgy are discussed.

Jan 1, 1981

By W. H. McFarland

The mechanical properties have been determined for a large number of alloy-free martensitic steels with carbon contents ranging from 0.08 to 0.20 pct and with manganese contents of about 0.4 to 0.5 pet. These steels were tested 1) as water-quenched, 2) after quenching, temper rolling, and tinning, and 3) after tempering treatments which involved temperatures from 400o to 1300oF and times from 1 min to 8 hr. The majority of these tests represent steel from commercial-size coils, i.e., strip 32 in. wide, coil weights up to 20,000 16, and steel thicknesses from 0.0055 to 0.024 in. As a result of these treatments, it has been shown that as-quenched low-carbon alloy-free steels can be produced with tensile strengths ranging from 140,000 to 220,000 psi and tensile elongations from 3.0 to 4.0 pet in 2 in. The tensile strength of the as-quenched martensites can be represented by the equation, tensile strength (ksi) = 119 + 560 (wt pet C). The response to tempering of these steels is related to previous work by Muir, Averbach, and Cohen and by Grange and Baughman. Strain aging of low-carbon martensite has also been investigated. If low-carbon steels are defined as those steels with a maximum carbon content of 0.2 pet, it is found that the literature on low-carbon, alloy-free martensites contains little data on the mechanical properties of these steels. However, the following facts concerning low-carbon alloy-free martensites seem firmly established:'-' 1) The major factors in controlling the strength of the martensite appear to be a) fine structure, b) the internal strain resulting from the transformation, and, particularly, c) the amount of carbon in solid solution. 2) In low-carbon steels, the martensite is auto-tempered and is in the form of needles with only minor amounts of internal twinning, whereas the martensite in high-carbon steels forms as plates which are internally twinned on a fine scale. 3) Care must be taken in comparing the results of work that has been done on low-carbon steels with varying amounts of alloying elements to data on plain carbon steels. As has been noted by Irvine, Pickering, and Garstone,6 alloying elements generally lower the martensite start temperature and, thereby, decrease the amount of auto tempering obtained during the quench. This makes it difficult to

Jan 1, 1965

Primarily, 1961 was a year for widespread application of tools and techniques which have become operational in the past several years • • • Raising --Raise climbers and climber raising techniques have been improved; narrow veins as low as 55° dip are now being mined from climber raises. Climber modifications include: larger motors, tighter radius curves negotiated, improved lubrication and new methods of stowing the climber during a blast. Climber raises are now ventilated in several ways: a 12-in. diam flexible vent tube behind the climber rail; a 6-in. diam pipe behind the climber rail (with fan); or a 6 to 8-in. diam drill hole along the axis of the raise. In hot raises, these ventilating techniques have resulted in more rounds per shift. When driving raises from crosscut and lateral development, mucking machine loading of raise rock is preferred over slusher ramp loading for the following reasons: a) faster set-up and teardown of climber facilities; b) easier access for climber maintenance, repair and loading of raising supplies; c) area at the bottom of the raise can be kept cleaner. Both wide and narrow veins are mined from 7 x 7-ft climber raises at Butte and at Republic, Wash. At Republic, climber rollers have been modified to support increased weight when driving 55°dip raises • Drilling-The new largebore, short-stroke push feed drills are much faster drilling than previous models and are most satisfactory in hard ground. Although reports on maintenance studies of the new drills are not yet available, increased steel and bit wear and breakage, and increased drill maintenance are seen as potential problems. Mines in Montana and Idaho continue to test rubber-collared drill steel. The fabricating methods used are successful but advantages in increased steel life have yet to be proved. Underground applications of down-the-hole drills continue. Drilling speed and accuracy are reported as the outstanding advantages. Manufacturers are now hopeful of making drills which will operate in any direction. Present applications are for ventilation holes (to 8 in. diam) for climber raises, holes for hydraulic fill distribution, drain holes and "predrilled" raises. Good drilling accuracy has been reported to a depth of 200 ft. Cutting holes in drifting is seen as a future application

Jan 2, 1962

By Eugene S. Meieran

The effects of methods of crystal growing, wafer sawing, polishing, routine handling, diffusion, and epitaxial growth on the defects in GaAs are reviewed and studied using reflection and transmission X-ray topographic techniques. In general, it was found that boat-grown crystals exhibited fewer defects than Czochralski crystals, although all crystals showed large numbers of precipitates visible when examined in the electron microscope. Mechanical surface treatments such as sawing and mechanical polishing introduce damage to a depth of about 5 µ, most of which can be removed by suitable chemical or chem-mechanical polishing. In addition, defects can be introduced through routine handling of wafers, for example with metallic tweezers. These defects can be quite severe, and have been observed 20 µ below the wafer surface. Defects can also be introduced through diffusion and epitaxial growth. These defects, which include precipitates, growth pyramids, stacking faults, dislocations, and so forth, can be detrimental to device fabrication. It is shown that wafers or films which appear defect-free optically can contain defects visible in the X-ray topographs. WHILE the use of GaAs in the semiconductor industry has increased very rapidly in the last few years, due mainly to the recent development of many important GaAs devices,1,2 the major limit to the production of commercial quantities of many GaAs devices remains a severe lack of suitable materials technology. This lack is apparent in two critical areas. First, production quantities of high-quality GaAs crystals, reproducibly doped and precipitate-free, simply are not available commercially, although some reasonable quality material is available on a limited first-come, first-serve basis. Second, in comparison to silicon technology, little is known about the effects of processing variables on the defects either present in as-grown GaAs or introduced through processing and handling of wafers. These areas are now receiving some attention from semiconductor device manufacturers, who are studying defects in GaAs in order to better understand how either to prevent their occurrence or to cope with their existence. Most investigations of the defects in GaAs have been made by optical microscopy3-5 or transmission electron microscopy techniques.'-' Recently, however, the imaging techniques of X-ray topography, electron mi-croprobe analysis, and scanning electron microscopy are being applied to the study of GaAs.9-14 In the case of X-ray topography, a one-to-one image is obtained that must be photographically enlarged. In compensa- tion, the defects within entire wafers may be imaged by simple scanning (Lang technique15) if the wafer is reasonably perfect, or by using the scan oscillation technique developed by Schwuttke16 if the wafer is warped or distorted. The purpose of this paper is to both review and extend the general application of X-ray topographic techniques to GaAs. Emphasis will be placed on the effects of growth and process variables on the quality and perfection of both bulk and epitaxial GaAs. Reference to optical or electron microscopy results will be made when useful. Since the effects on defects of a wide variety of processing variables such as crystal growing, sawing, polishing, diffusion, and epitaxial growth will be somewhat superficially reviewed, a fairly extensive bibliography of the most important recent results in these areas is included. However, for completeness, important defects will be illustrated here, although such defects have been previously shown by others. While this paper is concerned with defects rather than with the physics of X-ray scattering, the mechanisms of contrast formation in the topographs will of necessity be briefly mentioned. EXPERIMENTAL GaAs crystals, both boat-grown18 and Czochralski-grown,'8 containing a variety of dopants of various concentrations, were purchased from outside vendors. Wafers were sliced from the crystals using a Hamco ID saw and were mechanically polished using 1 µ diamond paste. Chem-mechanical polishing was done in bromine-methanol as described by Sullivan and Kolb.18 Chemical polishing was done using a modified sulfuric-peroxide solution, 11 parts H2SO4, 1 part 30 pct H2O2, 1 part DI water.5 Zinc diffusion was carried out in a closed tube, using a 10 pct Zn-In source at 825°C for 1 hr. Oxide masking techniques were used to select the area to be diffused. Epitaxial wafers were either purchased or prepared here. All epitaxial runs prepared here were carried out using a Ga-GaAs-AsC13 source in a closed tube at a substrate temperature of 750°C. Wafers were chem-mechanically polished and gas-etched prior to deposition. The X-ray topographs were taken on a Krystallos Lang camera, operating in the transmission scanning geometry (Lang technique15) or in the reflection scanning geometry (modified Berg-Barrett technique20,21). MoKa, radiation was used for all transmission topographs using a Jarrell-Ash 100-µ spot focus. CuKal radiation was used for all reflection topographs using a General Electric CA-7 1-mm spot focus X- ray tube. Topographs were printed from an intermediate contrast inversion film, so the contrast shown in all figures here is the same as that of the original 50-µ-thick emulsion L4 Iiford nuclear plate used to record the topograph.

Jan 1, 1969

CENTRAL EMERGENCY COMMITTEE Chairman, MRS. H. N. SPICER As no further requisition will be Made for knitted garments, for the boys of the 27th Engineers, all completed garments and wool have been collected and returned to Mr. W. R. Ingalls, and the activities of the

Jan 12, 1918

By M. H. Waxman, L. J. M. Smits

A simple physical model was used to develop an equation that relates the electrical conductivity of a water-saturatedshaly sand to the water conductivity and the cation-exchange capacity per unit pore volume of the rock. This equation fits both the experimental data of Hill and Milburn and data obtained recently on selected shaly sands with a wide range of cation-exchange capacities. This model was extended to cases where both oil and water are present in the shaly sand. This results in an additional expression, relating the resistivity ratio to water saturation, water conductivity and cation-exchange capacity per unit pore volume. The effect of shale content on the resistivity index - water saturation function is demonstrated by several numerical examples. INTRODUCTION A principal aim of well logging is to provide quantitative information concerning porosity and oil saturation of the permeable formations penetrated by the borehole. For clean sands, the relationships between measured physical quantities and porosity or saturation are well known. However, the presence of clay minerals greatly complicates log interpretation, particularly the electrical resistivity and SP logs, and considerably affects evaluation of hydrocarbon-bearing formations. The conductance and electrochemical behavior of shaly sands and their relation to log interpretation have been studied by many workers. wylliel and Lunch2 reviewed this work in some detail. Virtually all laboratory measurements of electrical resistivity and electrochemical potential of shaly sands published to date are the work of Hill and Milburn.3 Their measurements were made on about 300 cores covering a large variety of sedimentary rocks, and a wide range of equilibrating NaCl solution concentrations. Hill and Milburn described their conductivity data by an empirical equation in which the shaly sand conductivity Co was expressed as a function of the solution conductivity C and two parameters b and F01 . The quantity b was shown to be a measure of the effective clay content of the rock, being approximately proportional to the cation-exchange capacity of the rock divided by its pore volume. The latter ratio is designated as 9, in this paper and has the dimensions meq/ml or equiv/liter. Qv is identical with the term representing the concentration of fixed charges in the Meyer-Sieved and Teorel15 theory of permselective membrane behavior. F01 is a formation resistivity factor referred to a hypothetical equilibrating solution resistivity of 0.01 ohm m at 25C,* where clay effects presumably are minimized. F01 was correlated to porosity by an Archie-type equation.6 The Hill-Milburn equation describes their data with a standard deviation of approximately 1 percent and a maximum deviation of + 10 percent. Shaly sands behave as permselective cation-exchange membranes, their electrochemical efficiencies increasing with increasing clay content. The electrochemical potential data of Hill and Milburn were expressed graphically, and demonstrate that the membrane efficiency (or cation transport number) of these sands is a function only of the b value (i.e., Qv) and the respective salt concentrations of the two solutions forming the liquid junction in the sand. The diffusion potentials are not dependent on F01 or any parameter relating to the porosity or pore geometry of the rock. The Hill-Milburn resistivity equation correctly predicts a decreasing sand conductivity Co with decreasing solution conductivity C?. However, at some low value of C,, the calculated Co-C, function goes through a minimum; with further decrease in C?, the predicted sand conductivity increases sharply. As pointed out by Hill and Milburn, an increasing value of Co with decreasing C, is physically meaningless. Since this occurs below the range of practical values of C,, the usefulness of the empirical equation is not affected when

Jan 1, 1969

By M. H. Loveman

The orebody described below has been rediscovered and developed within the last 3 years. It has, however, been known and worked by the Chinese for hundreds of years. When assay values and size are considered, it contains what is probably one of the largest single bodies of zinc and lead sulphides yet found. The tonnages developed at other places, as at Broken Hill, are much greater but the average zinc and lead sulphide contents are considerably lower than at Bawdwin. Bawdwin is situated in the semi-independent State of Tawng Peng, one of the numerous units which make up the Northern Shan States. These States are under British rule and are generally considered as a portion of Burma. They are governed as a separate administrative unit, however, under the Lieutenant Governor of Burma. Each State is under its own chief, or Sawbwa, who has considerable power over his own subjects. Bawdwin is approximately in latitude N 23°6', longitude E 97°201, about 50 miles south of the nearest point on the Chinese border and 450 miles north of Rangoon (Fig. 1). The period at which mining was first begun at Bawdwin is unknown. The most reliable records have been obtained by deciphering local Chinese inscriptions and from these it is concluded that the work dates back to at least the beginning of the 15th century. The first undoubted reference to the mines by a European is by Syrnes in 1795. Crawford in 1827 estimated the output of silver from the mines at $600,000 anually. At about the middle of the 19th century the rebellion of the Chinese Mohammedans in the neighboring Chinese province of Yunnan so weakened the power of the Chinese that the incursions of hostile tribes (Kachins) made work extremely dangerous. The mines were finally abandoned by the Chinese about 1868. The . closing down of the mines was probably not entirely due to outside causes but may have been influenced somewhat by the increasing difficulty of handling the water, as the workings gradually descended below the water level of the district. Several attempts were made by the Burmese kings, Mindon Min and Thebaw, to resume operations, but because of a

Jan 1, 1917

By Louis Stott

IT is well known that the oxide of beryllium was identified as a new "earth" in 17971 and the metal first isolated in 18272. The history of the many difficulties encountered by early investigators, the laboratory achievements of Lebeau3, Fichter4 and Oesterheld5, and the eventual development of methods for commercial production are well covered in the literature, particularly in the authoritative published work of Siemens and Halske6 reviewing their comprehensive investigation of the element. Accordingly it has seemed desirable to restrict this paper to the properties and uses of beryllium and its alloys.

Jan 1, 1936

Executive HOWARD N EAVENSON, Chairman FREDERICK M. BECKET EDGAR RICKARD ERLE V. DAVELER WILLIAM WRAITH Finance HENRY KRUMB Chairman PAUL D. MERICA J V W REYNDERS H G MOULTON, Consultant Admissions JOHN M LOVEJOY, Chairman GEORGE D BARRON - DONALD M LIDDELL ELI T CONNER - WILLIAM W LYNCH

Jan 1, 1935

[1-Iron and Steel JOHN A. MATHEWS, Chairman RALPH H. SWEETSEH. Vice-chairman WILLIAM CAMPBELL. Vice-chairrmn MAX ROESLER, Secretary Iron Ore R C. ALLEN W. 0. HOTCHKISS MAX ROESLER ERNEST F. BURCHARD THOMAS T. READ DWIGHT E. WOODBRIDGE M. M. DUNCAN WILLIAM KELLY CARL ZAPFFE]

Jan 1, 1928

By H. F. Ramstad, F. D. Richardson

The equilibria (a) SiOz +Hz =SiO +H20 and (b) Si + SiO, = 2Si0 have beet1 studied at temperatures of 1425"to 1600°C ad 1310°to 1485°C respectively. The stattdard free energy changes for the tzrro reactions are given by the equatiotts Combination of the results for both equilibria leads to tiotz removes certain anomalies in existing high-terlzperature data for equilibria involving silica and silicon in iron. In many metallurgical processes and in many laboratory investigations silicon monoxide undoubtedly plays an important role. It is unfortunate therefore that wide differences exist between the results obtained by different investigators1-7 in their studies of such equilibria as In an attempt to put our knowledge of SiO on a surer basis, an exhaustive study has been made of equilibria [I] and [2] at temperatures ranging from 1300" to 1600°C. Reaction [I] was studied by measuring the amounts of silica which could be condensed from streams of Hz or Hz + HzO which had previously been brought into equilibrium with silica at temperatures ranging from 1425" to 1600°C. Reaction [2] was studied by measuring the material that could be condensed from streams of Hz or argon which had been brought into equilibrium with mixtures of silicon and silica at temperatures ranging from 1310" to 1485°C. EXPERIMENTAL Materials. The silicon was "superpure" grade and contained less than 0.1 pct impurities. The silica was prepared from pure mineral quartz; this was crushed and treated with concentrated hydrochloric acid to remove particles of iron, washed with water, and finally dried at 120°C. For the hydrogen + silica reaction, the silica was sized to —20+100 mesh. For the silicon + silica reaction, the two materials were ground to a fine powder in an agate mortar. The hydrogen and argon were commercial oxygen-free gases. The gas streams were controlled with capillary flow meters and the volumes were measured by wet gas meters. After passing through the meters, the gases were partially dried by silica gel. The hydrogen for the HZ + SiOz reaction was then passed through palladised asbestos at 300°C and dried with magnesium perchlorate. The efficiency of oxygen removal was checked throughout the experiments by passing the gas over an electrically heated strip of nichrome, used as an indicator as described by Rathman and de itt.' When mixtures of HZ + Hz0 were required, the partial pressures of water vapor (1.8 to 22 mm) were obtained by passing the hydrogen through oxalic acid dihydrateg' lo held at various controlled temperatures, O.l°C, by means of a water bath. The hydrogen for the Si + Si02 reaction was purified by passing it over a mixture of 3 parts of magnesium to 5 of lime heated to 600°."l1 u The argon for this reaction was passed through titanium powder (-3/16 in. + 100 mesh) heated to 900°C. The nitrogen used to prevent the reaction products escaping from the condenser (see later), was deoxidized by copper or iron at 600°C. All these gases were finally dried with magnesium perchlorate. Furnace, Temperature Contr01, and Measurement A molybdenum resistance furnace was used for both sets of experiments. The reactions were conducted inside a high-grade alumina tube, 36 in. long and 1 in. in diam as indicated in Fig. 1. With this arrangement an even temperature zone (2"C) 4 cm long was satisfactorily obtained. The temperatures were kept constant by means of a proportional controller actuated by a Pt-Pt 13 pct Rh thermocouple. This was placed between the two alumina tubes, so that the temperature at the junction was 1400" to 1450°C. Up to 1485"C, the temperatures were measured with Pt-Pt 13 pct Rh thermocouples. For higher temperatures an optical pyrometer was used, this being sighted (through the glass window 1 in Fig. 1) on the end of the alumina tube, that held the SiOz or Si +SiOz mixture, 10 in Fig. 1. The optical pyrometer was recalibrated whenever a change was made in any part of the apparatus situated in the hot zone. Successive readings with the optical pyrometer were reproducible to within 1"C. Equilibrium Apparatus and Procedure. Hydvogen and Silica Reaction. The apparatus is shown in Fig.

Jan 1, 1962

By W. W. Mullins, F. A. Nichols

Solutions are developed, assuming surface diffusion and both internal and external volume diffusion, for the relaxation of bodies slightly perturbed from spherical and cylindrical geometries. Combined with those previously published for the nearly planar case, these results provide a means of gaging the relative contributions of the two diffusional proc-cesses in any given case. It is shown that in all sintering experiments to date, and probably in any attainable in practice, surface diffusion has played the dominant role, although most previous authors have assumed otherwise. It is also shown that surface diffusion predominates in normal field-emission tip blunting and also for the coalescence of gas bubbles introduced into metals by a bombardment. The surface-diffusion solutions for a perturbed sphere are combined with previous results for volume diffusion to show that the inclusion of interface diffusion permits considerably larger spheres to develop in diffusion-controlled precipitate growth before the onset of instability. A mechanism is also proposed for the spheroidization of precipitate platelets as well as rods. In a previous paper1 the relaxation of a nearly plane surface to flatness by the combined action of the transport processes of viscous flow, evaporation-condensation (in a closed system), volume diffusion, and surface diffusion has been analyzed under the assumption that all surface properties are independent of orientation. In this treatment, criteria were developed for deciding which process predominates, and solutions valid in the latter stages of the sintering of small wires and particles to a plane were obtained. A numerical solution, valid throughout the entire particle-sintering process for the case of surface diffusion, was subsequently obtained by the present authors.' It was found that the analytic solution (which assumed small slopes everywhere) is accurate to within -10 pct when the maximum slope of the profile is less than 0.3; the wire-sintering problem has also been solved nu- merically for the case of surface diffusion and here again the results converge to the analytic small-slope solution at late stages of the process, the two solutions agreeing in this case to within 10 pct when the maximum slope of the profile is less than -0.6. The purpose of this paper is to extend the perturbation solutions to nearly spherical and nearly cylindrical geometries. We treat only the two principal diffusional processes, i.e., surface and volume, but for these geometries we discuss volume diffusion both inside and outside of the solid. Our results, when coupled with Mullins' solutions1 for nearly planar surfaces, provide criteria for gaging the relative contributions of surface and volume diffusion to the over-all transport process in three basic geometries. A very interesting feature in the cylindrical case is the occurrence of instability for longitudinal perturbations with wavelengths greater than the cylindrical circumference, a classical result. This instability of the cylindrical surface is applied to give a quantitative explanation for the often-observed "erratic" pore closure in the late stages of the sintering of wire compacts; also, the theory previously presented for the spheroidization of rod-shaped precipitates by surface (interface) diffusion' is expanded now to include volume diffusion inside and outside of the particle. The results for circumferential perturbations on a long cylinder allow quantitative estimates for gaging the relative importance of surface or volume diffusion in the early stages of the sintering of spheres or wires. The results here demonstrate clearly that surface diffusion has played a very important, if not dominant, role in all sintering experiments discussed in the literature, although the surface-diffusion contribution to the kinetics has usually been ignored. The results for the sphere (surface-diffusion case) are added to the results obtained previously by Mullins and sekerka3 concerning instabilities of a growing spherical precipitate particle (with interface diffusion disallowed) to obtain a general solution to this problem including interface diffusion. The inclusion of interface diffusion is found to increase significantly the range of stability of a growing spherical precipitate for typical metallurgical cases. The following assumptions are made: (i) the initial surface lies everywhere near and has a slope differing only slightly from that of the reference

Jan 1, 1965

HOWARD N. EAVENSON, Chairman C. T. HAYDEN, Vice-chairman, Bituminous Coal Production CHARLES DORRANC~ Vice-chairman, Anthracite Coal Production HOWARD P. ZELLW, Vice-chairman, Evaluation of Coal for Coke Making W. H. F'LTLWEILER, Vice- Chairman Gas and Its Manufacture 3. B. MORROW, Vice chairman, Coal Preparation

Jan 1, 1928

Jan 1, 1962