Search Documents

By A. G. Jordan, W. Jeitschko, Paul A. Beck

The occurrence qf the V phase structure /Zr,Co,Ge, type) in ternary syste7ns (titanium, zivconium, niobium, lanta1urn) -(nickel, cobalt, iron)-(silicon, germanium) was incestigated. Nine V silicides and four V gertrlanides were found and their lattice constants are reporled. The lattice constants of twenty-one preri-ously identified E phases (TiNiSi type) are given. The average atomic volumes of these phases are discussed in relation to similar binary phases. ThE occurrence of a phase Ti4Ni4Si7 was first reported by Westbrook. DiCerbo, and peat' who gave it the name "V phase". They also reported the existence of an E phase TiNiSi. Subsequently a systematic study was undertaken in this laboratory to explore the occurrence of E' and V phases3 in related ternary systems. In the meantime the crystal structure of the E phase TiNiSi 4 and of the V phase Zr4CO4Ge 75,6 was determined. In the present paper the details of the V phase investigation and the lattice constants of the E and V phases are presented. V PHASES Alloy specimens of approximately 10 to 15 g were prepared by arc melting under argon (99.996 pct Ar) atmosphere. The starting materials were all of purity higher than 99.9 pct, with the exception of cobalt. which contained 0.14 pct Fe as the only major impurity. The weight losses were in all cases less than 2 pct, in most cases less than 1 pct. The samples were encapsulated in fused silica tubes with sufficient argon to yield about 1 atm pressure at the annealing temperature. After the homogenization anneal. Table I. the specimens were water-quenched. A representative portion of each specimen was then examined metallographically (etchant: 20 pct HNO,. 10 pct HF. 25 pct glycerine, 45 pct H20). Only minor amounts of second- and third-phase particles were observed in the specimens listed in Table I, with the exception of alloys Zr4Fe4Si7 and Ta,Fe,Si,. which contained an estimated 10 pct by volume of foreign phases. X-ray powder photographs were taken with a Seeman-Bohlin type focusing camera and Fe-KO radiation. Of the thirty possible combinations of elements in the ternary systems (titanium, zirconium. vanadium. niobium. tantalum)-(iron. cobalt, nickel)-(silicon. germanium) thirteen V phases could be identified. In the remaining seventeen ternary systems and also in the systems Cr-Ni-Si and (M0.W)-(Ni.Co)-Si no V phase was found at the composition 4:4:7 after annealing at temperatures between 900" and 1200'C. For the determination of the lattice constants of the V phases Debye-Scherrer photographs were taken using the asymmetric film arrangement and CrKcr radiation (ka1, = 2.28962A). Using the positional parameters, as determined6 for Zr,Co,Ge,. Table 11. intensity calculations were carried out for each of the V phases with the aid of a computer program.: Thus unequivocal indexing of the diffraction patterns was greatly facilitated. The lattice constants. Table I. were then computed by a least-squares fit of the high-angle lines with f (0) = cos2 Q as extrapolation function. Only few. if any. very weak impurity lines were observed, with the exception of the three iron alloys Zr,Fe,Si7. Zr4Fe,Ge7. and Ta,Fe,Si7. The agreement

Jan 1, 1970

J. B. Cohen (AVCO Mfg. Co.)-The model presented by the authors is only one of several possible mechanisms for low-temperature aging. It is true that the motion of dislocations to the copper atoms, followed by diffusion along the dislocation lines, is one such mechanism. However, the details of such a process which would :result in copper-rich platelets on (100) planes in the f.c.c. matrix are not clear. Furthermore, there is at least one other mechanism that may be used to e.xplain the authors' results, so that the data do not clearly favor the Turnbull model. The zones may form by "normal" diffusion. The diffusion constants would be higher at room temperature than extrapolated data would suggest due to vacancies trapped in the specimens in the quench. The diffusivity would then be multiplied by the ratio of the number of vacancies present at the solution temperature to that present at room temperature. These vacancies could remain in the alloy specimen for long times at room temerature, due to interaction with the copper atoms. ' The activation energy for diffusion is smaller than that for bulk diffusion at elevated temperatures for it is only that for the motion of vacancies existing after the quench; after these are used up, the aging process effectively ceases. It is somewhat questionable if the laws governing transformation kinetics can be directly applied to changes in elastic moduli, especially in the case of aging where the structure and the composition of the zones may be changing during aging, If such laws are assumed, it is possible to explain the exponential factor of % with this vacancy model. It is probable that the structure of the zones and the matrix match only on (100) planes. Certainly the precipitates that form in this system after various aging treatments show orientation relationships similar to those of the zones. Strains on the edges of the zone may set up fields which do not allow the zone to grow in an edgewise manner. The exponent in the growth of a thin plate in a direction perpendicular to its face would be %. It may also be that copper atoms are attracted to dislocations. If this is the rate-controllin factor in the growth process Ifthisthen an exponent of % or % may arise. The writer would like to know if the authors have tried plotting l/a; proportional to as might be expected for "dislocation drainage." R. H. Doremus (General Electric Research Laboratory)—An important new method for following the growth of Guinier-Preston zones is presented in this paper, and I wish to congratulate the authors on their experiments. Their interpretation of the results, however, is doubtful in certain respects. To determine the exponent m in Eq. [4] the authors plotted -log at against t to various powers (their Fig. 6). The initial value of frequency used for these plots was found by extrapolating the data to zero time. In Fig. A the data from their Fig. 2 are plotted against a linear, rather than logarithmic, time scale. To obtain graphs similar to their Fig. 6 for these data one must use an initial frequency of about 52720; such a plot for m = % is shown in Fig. B. The straight line in Fig. B fits the data in an intermediate range only. The curve drawn in Fig. A was mapped from this line; comparison of

Jan 1, 1960

By A. D. Rich

The term "bleaching clay" or "bleaching earth," as used in the oil industries, refers to clays that in their natural state, or after chemical or physical activation, have the capacity for adsorbing coloring matter from oil. There are three common types of bleaching clays: fuller's earth, activated clays, and activated bauxite. Fuller's earth, or naturally active clay, is prepared from bentonites (see Chap. 5) that possess natural activity. It is not activated commercially; in fact, earths of this type ordinarily do not respond satisfactorily to acid activation. Fuller's earth is prepared in pulverized as well as granular form for use in the contacting and percolation processes, respectively. Acid-activated clays also are of bentonitic origin. The basic raw clay, however, is of a type that has a very low natural activity but is highly activable by treatment with mineral acid. Commercial acid-activated clays generally possess several times the decolorizing power (bleaching efficiency) of the best quality of fuller's earth. The former are prepared commercially only in the pulverized grade because of the difficulties in obtaining a satisfactory granular product, and hence are used only in the contact process. Activated bauxite is made by heat-treating bauxite ore, which in its natural state has very little natural activity. The commercial product is prepared in granular form for use in the percolation process on petroleum oils. For the most part, bleaching clay is used commercially in the decolorization of animal, vegetable and petroleum oils, fats and waxes. It is applied in two ways: (1) by the percolation method and (2) by the contacting method. Percolation refers to the passage of oil through a bed of granular clay whereas contacting refers to direct agitation of oil and pulverized clay followed by removal of the clay from the oil by filtration. In either case, the decolorizing effect is obtained by intimate contact between the liquid oil and the solid adsorbent. Petroleum oils are treated commercially by either the percolation or the contact process. Animal and vegetable oils are treated by the contact process only. Composition The raw clays from which both fuller's earth and acid-activated clays are prepared are composed of hydrous aluminum silicates containing varying quantities of magnesium, iron, calcium and other elements. These raw materials are usually nonswelling bentonites derived from volcanic ash or lava by weathering and hydrothermal chemical reactions. The bentonites have as their chief mineral constituent montmorillonite, which has the formula [(OH)4Si6A14O20•nH2O], according to Grim. (See Chap. 5, ref. 6, p. 91.) The underlying reasons are not fully known for the natural activity of the fuller's earth type of clay and its usual failure to further activate with mineral acid in contrast to the natural inactivity of the activatable type of clay. However, it may be said that the bentonites that are responsive to the acid-activation treatment generally have not undergone any drastic metamorphism. The chemical composition is not a reliable means of discrimination between a nonactive, a naturally active, and a nonactive but activable clay, therefore it is not possible to forecast the ultimate quality of a clay on the basis of the raw-clay analysis alone. Table 1 gives typical analyses of representative clays of the foregoing classifications.

Jan 1, 1960

By O. N. Carlson, W. M. Paulson

A phase diagram is proposed for the Y-C system based on the vesults of thermal analyses, microscopic obsevvations, and X-ray diffraction studies. Three intermediate phases occur in the system: a congru-ently melting fcc phase with a wide range of homogeneity about the composition Y2C, an intermediate solid-solution region between 55 and 58 at. pct C, and a bct dicarbide melting congruently at 2415°C. All three compounds undergo a phase transformation at elezlated temperatures. A continuous serzes of solzd solutions exists between the fcc phase and the high-temperature form of YC2 with a maximum in the solidus at 2000°C and 30 at. pct C and a minimum at 1805°C and 54 at. pct C. THIS investigation of the Y-C system was undertaken as part of a nuclear materials development program. Yttrium-base alloys are of interest as possible containers for liquid metals, and carbides are currently receiving increased attention as high-temperature materials for advanced reactors and other applications. Previous work on this system was limited in scope, and the results were somewhat inconclusive and at times contradictory. Spedding et al.&apos; reported the existence of a triyttrium carbide having an fcc structure with a wide range of homogeneity and Dean et a1.2 reported the existence of a rhombohedra1 phase having the stoichiometry of Y2C. Bachella et a1.3 observed that the latter was the result of ordering of carbon atoms in the fcc solid solution. The ordering range was placed at 800" to 1000°C. Vickery et a1.4 reported a high-melting compound which they identified as yttrium dicarbide, and Spedding and coworkers1 determined the structure of this phase as bct with lattice parameters a = 3.66 and c = 6.17A. Samsonov et al.5 reported the melting point of YC2 as 2300" * 50°C. Recently Bowman et a1.6 found a transformation in the dicarbide from the tetragonal to an fcc form at 1320 20°C. Samsonov and coworkers7 reported a monocarbide of yttrium melting at 1950" * 20°C and also a sesqui-carbide melting at 1800" * 50°C. The existence of the latter has also been indicated by others,1&apos;8 but neither compound has been definitely established. The Y-C phase diagram shown in Fig. 1 was proposed by Chubb and Keller8 in 1964 based on the data available at that time. The tentative nature of this diagram together with the uncertain status of the compounds indicated that additional work on this system was needed. EXPERIMENTAL PROCEDURE Yttrium metal of 99.9 pct purity was prepared for use in this study by the reduction of YCl, with calcium to form a sponge product.9 The major impurities in this material were as follows: 100 ppm C, 150 pprn H, 20 ppm N, 300 to 1000 ppm O, <20 ppm Ca, <100 ppm Cr, <80 ppm Cu, 150 ppm Fe, <30 pprn Mg, <400 ppm Ta, and <100 ppm Ti. Alloys were prepared by arc melting yttrium sponge together with pieces of high-purity graphite rod in a purified argon atmosphere. Homogeneity was insured by repeated melting, inverting the ingot between melts.

Jan 1, 1969

By R. C. Hall

The magnetic anisotropy and magnetostriction of single crystals of alloys between 25 and 59 wt pct Co in Fe have been determined in the disordered and ordered states. The magrzetostriction is large and positive for all alloys in both states of order (up to 150 x 10-6 for A,, and 40 x 10-6 for 111). The magnetic anisotropy becomes zero rzear 41 pct Co for the disordered state. Ordering shifts the zero-anisotropy composition to about 50 pct Co. COBALT-iron alloys have for many years been of interest as magnetic materials because they have unusually high magnetic saturation values.&apos; This interest was increased recently by the development of Supermendur.&apos; Supermendur is an alloy of 49 pct Co-49 pct Fe-2 pct V* which was found by suitable purification and heat treatments, including a magnetic anneal, to possess excellent magnetic properties. These included a square hysteresis loop with a low coercive force and a high magnetization, and a low total loss. Two factors which are important in determining the magnetic hysteresis properties are the basic magnetic properties of magnetostriction and anisotropy. Alloys having zero anisotropy and zero magnetostriction show improved hysteresis properties.3 Since very meager data4-&apos; are available in the literature on the single-crystal anisotropy and magnetostriction of the cobalt-iron alloys, the present program was undertaken to determine these two properties in the disordered and ordered states. EXPERIMENTAL TECHNIQUES Ingots of the cobalt-iron alloys containing from 25 pct to 59 pct Co in iron were vacuum melted from electrolytic iron and cobalt of 99.9 pct purity. The ingots were cooled at a rate of about 1°C per hr through the transformation temperature (950" to 980°C dependent on the alloy content) for the growth of large grains. From these grains, single-crystal disks were fabricated with either the (110) or (100) plane parallel to the faces of the disk. The crystals were given two heat treatments to produce either the ordered state (cooling rate of 20°C per hr from 850 "C) or the disordered state (water quench from 850 °C). Since the iron-cobalt alloys order very rapidly, the water quench may not have produced complete disorder in all cases. Due to the method of growth, the crystals were not perfect. Most of the samples had low-angle boundaries and a few had some small included grains. These imperfections could and probably did affect the accuracy of both the magnetic anisotropy and magnetostriction measurements. Much of the scatter in the data may be attributed to the crystal imperfections. The methods of determining the spontaneous saturation magnetostriction and the anisotropy have been previously described.419110 MAGNETOSTRICTION The magnetostriction in the [loo] and [Ill] directions (hO0 and ?111 respectively) is illustrated in Fig. 1 for the disordered state. Both ?100 and ?111i became large positive values as cobalt was added to iron. The state of order did not have a large effect on the magnetostriction. The effect of order did not appear too consistent in these data. Tentative curves are shown in Fig. 1 for the ordered magnetostriction near the FeCo composition; here ?100 appeared to be lowered and ?111 raised as the degree of order was increased. These results agree qualitatively with the

Jan 1, 1961

By D. G. Westlake

NUMEROUS hydride habit planes in zirconium, Zircaloy-2, and Zircaloy-4 have been observed by various researchers and have been compiled by Louthan and Angerman.1 While only partial agreement exists on the identification of these habit planes, there is a growing consensus that a tensile stress applied on a polycrystalline rod during slow cooling will cause the hydride platelets to lie perpendicular to the tensile axis. walters2 agrees with Louthan and Angerman who reason that "The particular plane on which precipitation will occur is the plane that will result in the maximum relief of stress by precipitation of the low-density hydride." The experiment described below was initiated to test this hypothesis on a single crystal of zirconium. A single-crystalline tensile specimen of zone-refined zirconium, designated number 13 in a previous study,3 had a square cross section with one pair of parallel faces only 4 deg from the basal plane of the hcp structure. The tensile axis was about 86 deg from the (0001) pole, 14 deg from the (1010) pole, and 16 deg from the (1150) pole. The specimen was charged to 50 ppm H by allowing reaction with the correct amount of hydrogen at 1073°K, homogenizing at this temperature for 2 hr, and cooling in the furnace. Two- surface analysis revealed that hydride platelets had precipitated parallel to the three {1010} prism planes. The specimen was heated to 673°K, in air, for 16 hr to bring the hydrogen back into solid solution, and furnace-cooled to 573°K.* It was then stressed in ten- sion at 1.2 kg per sq mm. (This produced a resolved shear stress of 0.6 kg per sq mm for glide on the prism plane with the highest Schmid factor. A higher stress would have produced significant strain at this temperature because the critical resolved shear stress for prism-plane glide in this crystal was only 1.0 kg per sq mm at ambient temperature.) The poles of the three prism planes were at angles of 14, 46, and 74 deg to the tensile axis so that an applied stress would exert normal stresses on the three planes in the approximate ratios 10:5:1, respectively. As soon as the stress was applied, the sample was furnace-cooled to room temperature. It was ground on wet Sic paper and chemically polished in 50 parts HNO3, 50 parts water, and 7 parts HF before examination. The result of the experiment was negative; i.e., the three (1010) planes were of equal importance as hydride habit planes.* It must be admitted that the ex- periment is not entirely comparable to those performed by walters,2 Louthan,5 and Louthan and Marshall6 on polycrystalline materials. They have found that some critical stress (below the macroscopic yield stress) is required for stress-orienting the hydrides. The applied stress in the present experiment was, by necessity, smaller by an order of magnitude than the critical stresses they report for the various materials. If the critical stress was related to the microstructure, one might postulate that it should be decreased by increasing the degree of perfection of the metal lattice and by increasing the grain size. But the experiment above suggests that, for the extreme case of a zone-refined single crystal of zirconium, the critical stress lies above that which one can apply without introducing gross plastic strain as another variable.

Jan 1, 1967

By T. R. Ingraham

When aluminum sulfate was decomposed in an evacuated apparatus and the sample cooled, Q alumina was found. The thermodynamics of the decomposition reaction were resolved by measurements of the total pressure of SO3, SO2, and O2 generated over the sample at various temperatures. The results were correlated with other published data to calculate the rmges of thermodynamic stability of the various compounds involved. The thermal decomposition of aluminum sulfate was studied by Wijhler, Pluddeman, and Wöhler1 and by Warner and Ingraham.2 The results of both studies were critically reviewed by Kellogg,3 who observed that "each set of data shows considerable scatter and strong curvature on a plot of log pso3 vs 1/T".3 He agreed with Warner and Ingraham2 that both the discrepancy in the two sets of results and their curvature may arise from the indefinite properties of the particular form of A12O3 which is formed during the decomposition. While studying the thermal stability of other sulfate systems, we had noted the presence of nonequilibrium oxide properties in both the cobalt4 and manganese5 systems, but neither had shown any appreciable curvature on a logPSO, vs 1/T relationship, and the data from both systems agreed reasonably well with prior work. It therefore seemed reasonable to reexamine the technique which had been used in our earlier work on aluminum sulfate.2 The principal difference was that a tightly compacted pellet had been used for the earlier aluminum sulfate work, whereas a loose powder, contained in a platinum boat, was used for our work on other sulfate systems. In addition, a better technique had been developed for dehydrating the samples. From work done on the nickel system,6 we had become aware of the highly protective nature of some sulfate layers on their oxjdes, and hence of the necessity of providing a large surface area of P3e sample when equilibrium was to be attained in a reasonable time. That observation suggested that perhaps a steady state, rather than equilibrium, had been reached in the earlier work on aluminum sulfate. This paper reports a repetition of the experimental work with large, finely divided samples of anhydrous aluminum sulfate. APPARATUS AND PROCEDURE The apparatus used in the experimental work was described in earlier papers.2,7 The source material was Anachemia reagent-grade Al2(sO4)3 - 18H2O which was first partly dehydrated by heating at 400°C for 48 hr and then completely dehydrated by repeated baking of an aluminum sulfate-oleum slush to dryness at 450°C. ? Alas was prepared by decomposing some of the sulfate in a muffle furnace at 800° C overnight. Approximately equal amounts of the 7) alumina and aluminum sulfate were used in the experiments. The finely divided samples were handled under dry box conditions, and in addition some of the aluminum sulfate was decomposed in the apparatus while it was under vacuum, to ensure its complete dehydration prior to sealing the apparatus. The samples were heated to a series of constant temperatures on both increasing- and decreasing-tem-perature programs. Two to three days were required to obtain steady readings of the total decomposition pressure on an increasing-temperature program, and 5 to 6 days on a decreasing-temperature program. Three samples were examined on both programs. Within experimental error, the results for each sample and each program could not be distinguished.

Jan 1, 1969

University of Alaska College, Alaska Mining Society (Inactive) H. G. WILCOX, Faculty .Sponsor University of California Berkeley, California Mining Association. OLEG D. SCHERBININ. President CHARLES S. PRATT, Secrctary LESTER C. UREN, Faculty Sponsor

Jan 1, 1944

PRESIDENT AND DIRECTOR CHESTER A. FULTON NEW YORK, N. Y. PAST PRESIDENTS AND DIRECTORS EUCENE MCAULIFFE OMAHA, NEBR. C. H. MATHEWSON NEW HAVEN, CONN. TREASURER AND DIRECTOR ANDREW FLETCHER NEW, YORK, N. Y.

Jan 1, 1944

By W. L. Doyle

SLAG weights were taken on a series of twenty-eight 6-ton bottom-pour heats. These weights varied from 573 to 1050 lb. Of these, four were chosen for study of the effect of cleaned and uncleaned foundry scrap on the variations of slag weights. Data regarding the make-up and results of the heats are given in Table I. For heat No. 3 the actual slag weight was checked, using the Mn-MnO calculation method-weight 1050 lb. [5,600 X 0.0055 = 30.80 heads and gates 6,000 X 0.004 = 27.00 plate scrap 800 X 0.0083 = 6.64 pig iron 450 X 0.0034 = 1.53 iron ore]

Jan 1, 1947

By Paul Cherin

ThE angle of intersection, 0, between h2k2l2 planes and the (loo), (110), (101), and (111) planes was calculated on an IBM 7040 using the well-known relationship

Jan 1, 1968

OFFICERS AND DIRECTORS For the year ending February, 1932 PRESIDENT ROBERT E. TALLY JEROME, ARIZ. FREDERICK W. BRADLEY SAN FRANCISCO, CAL. WILLIAM H. BASSETT,P WATERBURY, CONN KARL EILERS NEW YORK N. Y.

Jan 1, 1929

By R. F. Burdyn

The inadequate use of centrifugation to economically recover solids from weighted drilling fluids reflects the need for better equipment and techniques for this putpose. Laboratory studies in the development of an improved separator are described in which an operating equation is derived and tested. Results show that the concentric cylinder geometry employed effectively separates bnrite from a suspension and that the operating equation provides a good approxinmtion for scale-up. INTRODUCTION Our current drilling technology frequently requires a high-density drilling fluid obtained by addition of barite. In the course of drilling, formation solids which are too fine to be removed either by screening or settling become suspended in the drilling fluid and gradually the volume of solids in the mud increases. The volume fraction of solids must be limited (if a satisfactory set of rheological parameters are to be maintained). A centrifugal separatorprovidesan economical way of accomplishing this. The barite recovery process can be considered as a separation of two solids. One, the light solids, composed of formation and added solids, has a specific gravity of 2.6 to 2.7; the other, barite, has a specific gravity of 4.2 to 4.3. This density difference, plus the fact that the average light-solids particle size is much smaller than the average barite particle size, permits separation by a centrifuge. In drilling fluids some of the coarse particles of the light-solids-range will settle faster than fine particles of the barite-particle range. As a result a complete separation of the two species is not possible. since the object of the process is not merely recovering the maximum amount of barite but includes as well removing the maximum amount of light solids, an optimum barite recovery efficiency exists. From a practical standpoint this optimum cannot be determined in the field for each drilling fluid system, and in practice the separation is less than optimum, with some sacrifice of barite. Drilling technology has included centrifugal separators for barite recovery for more than a decade. Results have been reported by a number of investigators indicating that the process is practical and economica1. l-4 The decision to use a centrifuge is based on economics in which direct cost savings and the indirect benefits in rig time derived from improvement of the drilling fluid are important factors. One would expect that centrifugal separation of barite from drilling fluids would significantly affect barite consumption; however, this is not the case. The Minerals Yearbook shows an annual domestic barite consumption in the drilling industry of nearly 1 million tons.5 By rough estimate there are perhaps 80 separators presently in field use. Assuming half of these in use at any one time, operating an average of four hours per day, at recovery rates averaging 3,000 Ib of barite per hour, total annual recovery is about 90,000 tons. This is less than 10 per cent of he total barite used. I conservatively estimate that barite consumption in drilling operations can be reduced by 30 per cent through greater utilization of centrifugal separators. To encourage more widespread acceptance of centrifugal separators in the drilling industry, improved equipment and techniques would be very desirable. The present paper, covering theory and results obtained from a laboratory model, is the first in a series on he development of an improved mud separator for field use. THE CONCENTRIC CYLINDER GEOMETRY AS A SEPARATING DEVICE Consider the geometry shown in Fig. 1, consisting of two concentric cylinders separated by an annular space. These are arranged so that the outer cylinder is fixed and the inner one can be rotated about its axis on shafts sealed against the ends of the outer cylinder. If the outer cylinder is fitted with openings at either end, the inner

Jan 1, 1966

By G. Sandoz, D. A. Meyn

The fracture surfaces of specimens of titanium a1loys which exhibited susceptibility to subcritical crack growth in a wide variety of environments, including aqueous solutions, alcohols, hydrocarbon gases, carbm tetrachloride, and dry air, were examined. The dominant and characteristic fracture mode was cleavage. which became mixed with an increasing porportion of ductile fracture modes (dimples. and so forth) as the applied KI was increased. The cleavage plane in all the alloys was oriented at 15 deg from (0001) of the a phase. No indices could be assigned to the 15 deg cleavage Plane because of uncertainty as to which zone it belonged to. SLOW crack growth and delayed fracture take place in certain titanium alloys at stress intensity (KI) lower than the critical values for complete fracture (KIc) found in short-time tests for plane strain fracture toughness.&apos; Such crack growth may take place in very dry air on sustained loading if the alloy contains a sufficient amount of hydrogen and if the stress intensity factor is higher than a threshold value designated KIH.2 Similarly, a number of environments such as water, alcohols, and hydrocarbons may cause slow crack growth provided the stress intensity factor exceeds the threshold value KISCC. In this paper it is intended to examine some fracto-graphic and crystallographic details of this subcritical crack propagation process as related to alloy composition, environment, and stress intensity. It has been previously reported that subcritical crack growth takes place in titanium alloys in aqueous environments by cleavage.2"6 The observations to be described here indicate that in the alloys investigated the mode of subcritical crack propagation is more dependent on the stress intensity during cracking than on the environment. The fracture mode is illustrated with photographs of the fracture surfaces at a wide range of magnifications. The crystallographic character of the cleavage mode is also presented and the results discussed. EXPERIMENTAL APPROACH The studies were made on four titanium alloys— Ti-8A1-1Mo-lV, Ti-5A1-2.5Sn, Ti-7Al-1Mo-lV, and Ti-0.350. Of these four alloys the first two were mill annealed and fine grained. The latter two were noncommercial and coarse grained, having been prepared for other experimental purposes. The crystallographic studies required a large-grain size. Consequently the fine-grained alloys were an- nealed in a vacuum at 1950°F and furnace cooled to produce samples for these studies. This treatment did not alter the microstructure significantly except for grain size. All the aluminum-containing alloys showed primary a with a network of ß-phase particles within the a grains; Figs. 1 and 2 show this microstructure for the specific case of fine-grained Ti-8A1-1Mo-1V. The cracks in the figures will be discussed later. Fractographic studies were made on all the alloys, but the electron fractographs displayed herein are from the Ti-8A1-1Mo-1V alloy in the fine-grained condition. Emphasis was placed on this commercial alloy because considerable information was available on the stress-corrosion cracking characteristics in a variety of environments. Sufficient supplementary studies of the alloy after the anneal to produce large grains were conducted to establish that the stress-corrosion cracking susceptibility and fractographic characteristics were not changed significantly. Thus it could be inferred that the crystallographic data obtained exclusively on large-grained specimens would apply also to fine-grained specimens. Fracture surfaces for study were obtained using precracked cantilever beam specimens loaded as described by Brown. The precracked section of a specimen was immersed in the environment of interest. Values of initial stress intensity factor Kli were chosen slightly higher than KISCC in order to obtain a fairly extensive region of slow crack growth. Fracture surfaces representative of a variety of stress intensity levels could then be examined because in the cantilever beam test KI increases as the crack propagates.

Jan 1, 1970

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper .to, discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in. brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: 1-gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2-liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3-glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4-crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that carried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant, contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.1 At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1-aqueous solution, a much more expansible liquid, and a gas; 2-aqueous solution, salt crystals, and a gas; and 3-the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20° and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.2-6 Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid. carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.7,8 Hartley (1876, 1877),9,10 Hawes (1881),11 Wright (1881),12 Johnsen (1920),13 and Holden (1925)14

Jan 1, 1952

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By R. J. Grace

Primarily, this report presents the results of direct efficiency tests which were conducted on the 200-hp Coal-Pak, hot water generator, No. 3 unit, at the Otterbein College heating plant in Westerville, Ohio. Also included is a comparison of fuel consumption of the old plant with that of the new plant, a comparison of efficiencies obtained by the indirect method on a 300-hp Coal-Pak, and the cost of gas vs coal to show the savings effected by the latter. Tests were conducted with ten different bituminous coals selected by Mr. S. A. Frye, business manager at Otterbein College. The coals, of ten different suppliers, from four different states and eight different seams, represented competitive products economically available to the heating plant. The tests were conducted by the usual plant personnel which consisted of the plant superintendent and two assistants. No outside supervision of any kind was given during the tests. The tests were made from Dec. 13, 1960, through Mar. 4, 1961. During this period, 300.03 tons of coal were burned in the No. 3 unit. This tonnage represented 25.5 pct of the total coal requirements for the 1960-61 season. Operation during the period was typical for the comfort heat load which the plant supplies. Of the 78.12 operating days, the boiler was on bank or holdfire 14.31 days, or 18.32 pct of the time. The length of individual bank periods varied from 2 hr to three days. Run periods varied from about 2 hr to 7.26 days. DESCRIPTION OF PLANT AND HEATING EQUIPMENT The new Otterbein College heating plant, completed in the summer of 1957, is located in a 50x50 ft boiler room on the lower level of a combination maintenance building and heating plant. The building is situated away from the main college complex on a hillside, which allows for on-grade delivery of coal to the three bunkers. The bunkers are located directly above and connected with the individual stoker hoppers. Fig. 1 shows an in-plant view of the Coal-Pak installations. The No. 3, hot water, unit is at the extreme right. The heating plant consists of three 200-hp Coal-Paks. Unit No. 1 is operated at 4 psi and carries the steam heating load of 14,000 sq ft EDR (steam) installed in two buildings. Provision has been made to convert these buildings to hot water heating at some future date. Since the unit under maximum load conditions operates only at about 50 pct steaming capacity, a heat exchanger was installed to convert steam to hot water. Thus, during light loads in mild weather the unit can be employed more efficiently to supply both steam and hot water and eliminate the need for operating either of the two hot water units. Units No. 2 and No. 3 serve a hot water heating circuit for a large group of 21 buildings of the College. These boilers deliver hot water at temperatures up to 200°F to the various buildings through distribution lines in tunnels. The present calculated maximum heat loss for the College is 15.195 million Btu per hr. The Coal-Paks have individual design capacities of 6.700 million Btu per hr. Table I lists the design date for the Coal-Paks. The No. 3 unit was chosen as the test unit, primarily because of its bunker location at the far end of the delivery ramp. Because of this location any excess coal above bunker capacity could be conveniently stored and isolated from the adjoining bunkers. Each bunker has a capacity of 30 to 35 tons of coal. The No. 2 and No. 3 hot water generators are equipped with automatic controls which maintain the

Jan 1, 1962

By J. L. Brimhall, R. A. Huggins, M. J. Klein

IN a recent paper1 it was shown that small additions of magnesium, copper, and oxygen decrease the stacking fault probability in plastically deformed silver. Correlation of :X-ray data with measurements of the twinning frequency and metallographic observation of slip lines indicated that this effect may be due to an increase in the relative stacking fault energy. It is the purpose of the present note to report experiments on these alloys of known stacking fault probability that relate to the stacking fault contribution to electron scattering in silver. There has been a considerable amount of disagreement in the literature concerning the contribution of dislocations to electrical resistivity in metals. Calculations relating to the scattering of conduction electrons by the dislocation core, its strain fields, and related effects have been made by several authors.2-5 In addition, experimental work on Cu,3,6-10 Ni,11 and Ni-Co alloys1:! has shown that dislocations in those materials exert an anomalously large effect on resistivity, this effect being related to the presence of extended dislocations. The problem of the scattering due to the stacking fault region between partial dislocations has been treated theoretically using several different procedures.13-&apos;0 The results of these calculations show a wide range of predicted values, from rather large to completely negligible, due to the models and the approximations involved. Almost all of this work has been applied to the specific problem of scattering in copper. The more complete theoretical treatments depend rather critically. on the shape of the Fermi surfaces and the effective mass parameters. The scattering from stacking faults might therefore be expected to vary significantly from one metal to another. Unfortunately, sufficiently accurate information is not available .which would allow one to have any confidence in a theoretical prediction of the scattering in the case of silver. Resistivity measurements were made on small wire specimens of vacuum melted high purity silver and several dilute alloys. These measurements were made at approximately 20°C, with great care being given to temperature measurement and corrections. At such temperatures phonon scattering is significantly greater than imperfection scattering. However, the experimental technique was such that measurements on similarly treated samples were reproducible to better than 2.4 X 10-9 ohm-cm, which was satisfactory for this work. Values of the stacking fault probability and the increase in resistivity after severe plastic deformation are given in Table I. The increases in resistivity resulting from plastic deformation agree quite well with previous work on silver.14,21-26 In addition, it has been previously found that interetitials and vacancies in silver anneal out well below room temperature, so that the residual imperfection scattering in these experiments could be expected to be primarily associated with dislocations;. It is seen from the data in Table I that large changes in stacking fault probability are accompanied by differences in resistivity due to imperfection scattering of only a few percent. If the scattering of conduction electrons by extended dislocations is primarily due to the area of the stacking fault region independent of the stacking fault energy, and not the core and strain fields associated with partial dislocations, the resistivity increase should be proportional to the product of the dislocation density and the stacking fault width, as is the stacking fault probability. Therefore, the imperfection scattering caused by plastic deformation of the alloys should be considerably smaller than that found in the pure silver. Since this was not observed, these results sugegest the possibility that stacking faults do not themselves contribute appreciably to the electrical resistivity of silver deformed at room temperature. An alternative explanation of these observations is that the scattering by the stacking fault is roughly proportional to the stacking fault energy, rather than being determined by the total area of such faults. Sufficient evidence is not yet available to separate these two possibilities. This work was supported by the Office of Naval Research.

Jan 1, 1962

Prof. Henry S. Jacoby, Cornell University,Ithaca, N.Y. (communication to the Secretary): When a simple beam supports any given load, the lower fibers me in tension while the upper fibers are in compression, and if its cross-section is rectangular the neutral surface, where the stresses pass through zero from tension to compression, is at mid-depth, provided the elastic limit is not exceeded. In addition to the longitudinal stresses, there are horizontal shearing-stresses between the fibers which have their maximum value in the neutral surface, and which equal zero at the upper and lower surfaces, while there are also vertical shearing-stresses. Let another beam of the same dimensions be placed on top of this one, and the load be doubled, it then produces stresses in each beam of the same character, magnitude and distribution as in the preceding case, provided there be no friction between the adjacent surfaces of the beams. Next let these two beams be so firmly united that there will be no motion between them when the same load is again applied. All the fibers in the upper beam are now in compression, and those in the lower beam in tension, while the maximum stresses in the outer fibers are only one-half as large as before. The strength of the combined beams is therefore doubled. If, however, some motion occurs between the beams, then the stresses in some of the lower fibers of the upper beam pass from compression to tension, and those in some of the upper fibers of the lower beam from tension to compression, while the stresses in the outer fibers have a magnitude between the two values previously stated. These fundamental facts relating to the flexure of beams indicate the necessity of carefully designing the keys or brace-

Jan 1, 1898