Search Documents

ARTHUR PHILLIPS, Chairman C. S. SMITH, Past-Chairman L. W. KEMPF. Vice-Chairman. E. E. SCHUMACHER, Vice-Chairman H. A. MALONEY, Treasurer FRANK T. SISCO, Secretary °9 West 39th Street, New York 1S, N. Y. Executive Committee 1945 1946 S. BARRETT H. L. BURGHOFF T. A. WRIGHT GERALD EDMUNDS L. L. W MAN A. A. SMITH, JR.

Jan 1, 1944

Established as a Division November 17, 1948 B W Gonser, Chairman J C Kinnear, Jr, Past Chairman H H Kellogg, Chairman-Elect R C Cole, Vice-Chairman, '58 A E Lee, Jr, Vice-Chairman, '59 W R Opie, Vice-Chairman, '60 R W Shearman, Secretary AIME, 29 West 39th Street New York 18, N Y

Jan 1, 1957

By T. P. Papazoglou, N. A. D. Parlee, W. C. Phelps

PRACTICAL designs for good "home made" molybdenum furnaces are hard to find in the literature. The one described briefly below left something to be desired but was good enough to operate as a rather long (30 in.) two-zone furnace for periods of over 2 months at temperature (1400° to 1600°C) without shutdown. The principal problem in our application was to establish a temperature profile with two distinct constant-temperature zones and no dip between the zones. This and other problems mentioned below would not arise, however, if both zones were operated at the same temperature and if a shorter furnace were acceptable. Since molybdenum windings oxidize very rapidly when heated in air, impervious refractory tubes were used for both the furnace core and the outer jacket tube shown in the accompanying figures. A protective atmosphere of forming gas (10 pct H2, 90 pct N2) was continuously passed through the gas-tight annular volume between the core and outer jacket. The water-cooled copper ends shown in Figs. 1 to 3 sealed the ends of the tubes. Annealed molybdenum wire (40 mil) was wound on the recrys-tallized alumina core (35.5 mm OD by 28.5 mm ID by 30 in.) at a spacing of 0.36 in. The spacing was reduced to 0.29 in. close to the ends to partially compensate for end heat losses. Fig. 2 shows two molybdenum-ground lead taps off the center of the winding to produce the two independect temperature zones. The ground lead was insulated with 1/4-in. alumina tubing and connected to the grounded copper end by passing the wires through the gas port tube and crimping each wire into notches cut at the mouth. To prevent sagging of the core at high temperatures, refractory "troughs" were cut from alumina and mullite tubing to cradle the core. The support "troughs" which were 6 in. long and located about 5 in. from each end of the annular volume also served as radiation shields. In view of the different expansion coefficients and operating temperatures of the core and outer jacket (3.5 in. OD by 3 in. ID by 30 in.), the ends of the tubes were smoothed and squared to produce good sealing surfaces, and the core was ground 1/32 in. shorter than the outer tube. The power terminals were passed through their respective conductor ports which were internally lined with alumina tubing and sealed with Armstrong adhesive A-6 leaving about 1 in. of protruding lead wire for external connections. (Adhesive A-6 is a two-component system consisting of an epoxy-type resin with a mineral fibrous filler and an amine catalyst.) Figs. 1 and 3 show the entire assembly of concentric refractory tubes, copper ends, and sealing o rings, held together with two brass flanges and 3/8-in. bolts with heavy springs for dimensional flexibility. The furnace shell (19 by 19 by 30 in.) consisted of a steel frame with sheets of transite forming a box. The copper ends protruded through two 3.75-in. circular holes cut at the center of each transite square end. Thermal insulation next to the transite exterior was effected by K-23 B&W bricks alld in a central volume of approximately 9 by 9 by 30 in. a row of K-30 bricks was lined up to support the hot assembly. The rest of the volume around the outer

Jan 1, 1965

New York LOUIS D. HUNTOON, Chairman. ARTHUR S. DWIGHT, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. E. MALTBY SHIPP, Treasurer. GEORGE F. KUNZ, W. De L. BENEDICT. Boston ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston. Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH.

Jan 1, 1917

Executive HOWARD N. EAVENSON, Chairman FREDERICK M. BECKET EDGAR RICKARD ERLE V. DAVELER WILLIAM WRAITH Finance HENRY KRUMB, Chairman PAUL I). MERICA J. V. W. REYNDERS H. G. MOULTON, Consultant Admissions JOHN M. LOVEJOY, Chairman GEORGE D. BARRON DONALD M. LIDDELL ELI T. CONNER WILLIAM W. LYNCH Alternates WM. H. BASSETT, JR. L. B. LINDEMUTH W. A. SINSHEIMER

Jan 1, 1934

By John McDonald

THIS report is a continuation of an earlier one with a similar title,1 to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as re-ported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be com-pared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a con-siderable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated.

Jan 1, 1940

By W. H. Emmons

In 1922 Morey made a series of experiments in which he observed the cooling of a molten system containing H2O, 9.1 per cent; K2O, 17.3 per cent and SiO2, 73.6 per cent. This system was confined in a bomb; it was fluid at 500° C. and exerted no vapor pressure. In cooling to 420° C. a large part of it crystallized and at that temperature much of the water had separated from the crystals and remained as steam, which built up a pressure of 4998 lb. per sq. in., a force sufficient to lift nearly one mile of granite.' If granite, cooling at 600°, expels vapor in the process of crystallization it is reasonable to suppose that a considerably greater vapor pressure would result, and it is thought that the vapor expelled from crystallizing granitic batholiths probably has a pressure sufficient to lift two or three miles of granite. This vapor, collecting near the tops of cupolas of batholiths, is believed to exert sufficient pressure to fracture the hoods and roofs of batholiths above the cupolas. If that is true, one would expect to find that the fracture systems above cupolas are arranged in patterns that depend in part on the shapes of the cupolas. The mechanics of the situation seem to require that conical cupolas should have radial fracture patterns, that bluntly rounded cupolas should have fracture systems that are either irregular or rudely conjugated in plan, and that elongated stocks or cupolas should have fracture systems in which the fractu'res lie nearly parallel to the direction of the elongation of the cupolas. Study of essentially all the cupolas of the earth that have associated important vein-filled fractures shows that this is generally true. This

Jan 1, 1935

By W. H. Emmons

In 1922 Morey made a series of experiments in which he observed the cooling of a molten system containing H2O, 9.1 per cent; K2O, 17.3 per cent and SiO2, 73.6 per cent. This system was confined in a bomb; it was fluid at 500° C. and exerted no vapor pressure. In cooling to 420° C. a large part of it crystallized and at that temperature much of the water had separated from the crystals and remained as steam, which built up a pressure of 4998 lb. per sq. in., a force sufficient to lift nearly one mile of granite.' If granite, cooling at 600°, expels vapor in the process of crystallization it is reasonable to suppose that a considerably greater vapor pressure would result, and it is thought that the vapor expelled from crystallizing granitic batholiths probably has a pressure sufficient to lift two or three miles of granite. This vapor, collecting near the tops of cupolas of batholiths, is believed to exert sufficient pressure to fracture the hoods and roofs of batholiths above the cupolas. If that is true, one would expect to find that the fracture systems above cupolas are arranged in patterns that depend in part on the shapes of the cupolas. The mechanics of the situation seem to require that conical cupolas should have radial fracture patterns, that bluntly rounded cupolas should have fracture systems that are either irregular or rudely conjugated in plan, and that elongated stocks or cupolas should have fracture systems in which the fractu'res lie nearly parallel to the direction of the elongation of the cupolas. Study of essentially all the cupolas of the earth that have associated important vein-filled fractures shows that this is generally true. This

Jan 1, 1935

In 1922 Morey made a series of experiments in which he observed the cooling of a molten system containing H2O, 9.1 per cent; K2O, 17.3 per cent and SiO2, 73.6 per cent. This system was confined in a bomb; it was fluid at 500° C. and exerted no vapor pressure. In cooling to 420° C. a large part of it crystallized and at that temperature much of the water had separated from the crystals and remained as steam, which built up a pressure of 4998 lb. per sq. in., a force sufficient to lift nearly one mile of granite.' If granite, cooling at 600°, expels vapor in the process of crystallization it is reasonable to suppose that a considerably greater vapor pressure would result, and it is thought that the vapor expelled from crystallizing granitic batholiths probably has a pressure sufficient to lift two or three miles of granite. This vapor, collecting near the tops of cupolas of batholiths, is believed to exert sufficient pressure to fracture the hoods and roofs of batholiths above the cupolas. If that is true, one would expect to find that the fracture systems above cupolas are arranged in patterns that depend in part on the shapes of the cupolas. The mechanics of the situation seem to require that conical cupolas should have radial fracture patterns, that bluntly rounded cupolas should have fracture systems that are either irregular or rudely conjugated in plan, and that elongated stocks or cupolas should have fracture systems in which the fractu'res lie nearly parallel to the direction of the elongation of the cupolas. Study of essentially all the cupolas of the earth that have associated important vein-filled fractures shows that this is generally true. This

Jan 1, 1935

By W. H. Emmons

In 1922 Morey made a series of experiments in which he observed the cooling of a molten system containing H2O, 9.1 per cent; K2O, 17.3 per cent and SiO2, 73.6 per cent. This system was confined in a bomb; it was fluid at 500° C. and exerted no vapor pressure. In cooling to 420° C. a large part of it crystallized and at that temperature much of the water had separated from the crystals and remained as steam, which built up a pressure of 4998 lb. per sq. in., a force sufficient to lift nearly one mile of granite.' If granite, cooling at 600°, expels vapor in the process of crystallization it is reasonable to suppose that a considerably greater vapor pressure would result, and it is thought that the vapor expelled from crystallizing granitic batholiths probably has a pressure sufficient to lift two or three miles of granite. This vapor, collecting near the tops of cupolas of batholiths, is believed to exert sufficient pressure to fracture the hoods and roofs of batholiths above the cupolas. If that is true, one would expect to find that the fracture systems above cupolas are arranged in patterns that depend in part on the shapes of the cupolas. The mechanics of the situation seem to require that conical cupolas should have radial fracture patterns, that bluntly rounded cupolas should have fracture systems that are either irregular or rudely conjugated in plan, and that elongated stocks or cupolas should have fracture systems in which the fractu'res lie nearly parallel to the direction of the elongation of the cupolas. Study of essentially all the cupolas of the earth that have associated important vein-filled fractures shows that this is generally true. This

Jan 1, 1935

By W. H. Emmons

In 1922 Morey made a series of experiments in which he observed the cooling of a molten system containing H2O, 9.1 per cent; K2O, 17.3 per cent and SiO2, 73.6 per cent. This system was confined in a bomb; it was fluid at 500° C. and exerted no vapor pressure. In cooling to 420° C. a large part of it crystallized and at that temperature much of the water had separated from the crystals and remained as steam, which built up a pressure of 4998 lb. per sq. in., a force sufficient to lift nearly one mile of granite.' If granite, cooling at 600°, expels vapor in the process of crystallization it is reasonable to suppose that a considerably greater vapor pressure would result, and it is thought that the vapor expelled from crystallizing granitic batholiths probably has a pressure sufficient to lift two or three miles of granite. This vapor, collecting near the tops of cupolas of batholiths, is believed to exert sufficient pressure to fracture the hoods and roofs of batholiths above the cupolas. If that is true, one would expect to find that the fracture systems above cupolas are arranged in patterns that depend in part on the shapes of the cupolas. The mechanics of the situation seem to require that conical cupolas should have radial fracture patterns, that bluntly rounded cupolas should have fracture systems that are either irregular or rudely conjugated in plan, and that elongated stocks or cupolas should have fracture systems in which the fractu'res lie nearly parallel to the direction of the elongation of the cupolas. Study of essentially all the cupolas of the earth that have associated important vein-filled fractures shows that this is generally true. This

Jan 1, 1935

By N. M. Langdon

Spokane Meeting, September, 1909.) THE following corrections to the paper of Mr. Langdon (Bulletin No. 34, October, 1909, pp. 919 to 940), received after the publication of the paper in the Bulletin, will be incorporated in the paper as finally published in the forthcoming Vol. XL. of the Transactions, but are here presented for the information of members:' Page. 921. Table I., furnace M2, item 11. For " 8801 " read "0.8801." 922. Table II., furnace C, item 2, under gas. For " 0.011 C " read " 0.011 0." Furnace G, item 13, under gas. For " 5.074 air " read " 3.074 air." Item 15, 114.269 " should be " 4.289." Furnace H, item 2, under iron. For " 0.04 " read ".0.01." 923. Table II., furnace J, item 1, under iron. For " 0.95 " read " 0.93." Furnace N2, item 6, under gas. For " 0.66 CO," read 0.066 C02." 924. Table III., furnace C, item 17. For " 379 " read " 397." 927. Table IV., furnace C, item 4. For " 0.0124 " read 0.0424." Furnace G, item 15.. For " 4,060 " read " 4,066." 928. Line 2. Items 19 and 20 of heat-supply, should be items 20 and 21. 930. Line 3. Expunge remainder of paragraph after the word " supplied," and substitute the following : "As compared with the fusion-zone, the loss by radiation n C was 25.5 per cent. of the total (2,278 units) supplied to that zone, while in D it was 22.5 per cent. of the total heat (1,824 units) supplied to that zone. Finally, as compared with the reduction-zone, C lost by radiation 36.8. per cent. of the 1,580 units supplied to that zone,

May 1, 1910

By Morris Cohen, Robert C. Ruhl

The phases in Fe-C alloys over a wide composition range have been studied after splal quenching from the liquid state. Binary alloys containing 0 to 5.1 wt pel C as /cell as a large number of ternary Fe-C-Si alloys with 2.5 to 5.0 wt pct C and 0.3 to 5.1 wt pct Si were attlong those sludied. Olher Fe-C-X alloys, zcilh X being Co, Cr, ,Wn, Ni, and Ru , were also inrestigated after splat quenching. At high carbon contents, a new hcp phase (designaled 6 phase, but different from e carbide) is retained upon splat quenching. The .fraction of this phase varies up lo 97 pcl for a Fe-4.K-1.9% alloy. The composition of the E phase ranges from about 3.8 10 4.8 wt pet C, and the corresponding laltice parameters increase linearly ulith carbon content, while the c/a ratio remains essentially conslc~nl. The E phrtse appears to he a solulion of carbon in E iron, the latler being nornially found only at high pressures. It is deduced that the unit cell of the E phase corresponds to the formula Fe12C3, and llzal il is relaled to tlie ordered slruclures 0.f 6 iron carbide and c iron nilride. The E phase is compared and contrasted to the olher known carbides and nitrides of iron and nickel. An exlrapolaTion of the atomic volume 1,s carhon conlent of /he E pllase lzcts giz.en a neu7 estitnale jor /he alomic volume of E iron, 11.30 cu A, a1 atmospheric pressure and temperature. Other alomic volume relalionships lead to /he co~zpositioti Fe2.iC tor E iron carbide, /he unit cell fortr~ula being -Fe2rClo The E phase undergoes a lulo-slage decomposition upon healing, .forrning firsl rnarlensile plus E carhide, a/ler 1 hr at 140" lo 200°C, slid then ferr ite Plus cementile, after 1 lir a1 330" to 460°C. A1 carbo,l contents between 1.5 and 3.0 LC/ pcl, (he predo.wirzar/t plzase alley quenching is fcc austenite. The retained carbon content of this phase increases with itlcreasing silicon in certain concentration ranges, reaching a maximum of 2.37 wt pct C itz a Fe-2.6C-4.OSi alloy. This is the highest carbon conten1 reLaitled in austenite to date. These high-carbon aus-tenites can be partially tm?zsforttled lo tnartensile hy severe deformation in the temperature range of — 190 to -50°C. TECHNIQUES for splat quenching from the liquid state have been utilized in numerous recent investigations to produce metastable phases in a variety of alloy systems. Among the several ways of splat quenching, the shock-tube method appears to yield the highest cooling rates1-3, 7, 8 and was adopted here. Estimated cooling rates attained in the present experiments ranged from 10' to 10 80Cper sec.' As a part of a research program on interstitial al- loy phases, the Fe-C system was selected for splat-quenching studies. It was hoped that splat quenching would allow high metastable supersaturations of carbon to be retained in solution. Also of considerable interest were the conditions governing the occurrence of the various intermediate phases upon solidification. The alloys investigated included both binary Fe-C compositions as well as six ternary Fe-C-X alloy systems. The known phases in the Fe-C system are summarized in Table I.* Only the ferrite and graphite are ent investigation.14 and is described in detail herein Table II summarizes corresponding data on Fe-N phases, which are also of interest here because of their similarity to the Fe-C phases. EXPERIMENTAL PROCEDURES Alloys were prepared by melting the elements. 99.9 pct purity, in an inert gas nonconsumable electrode arc furnace. The buttons. weighing about 5 g. were remelted twice. were then fragmented. and their interior surfaces were examined for uniformity: if any doubt existed. they were remelted again. Chemical analyses were performed on all the alloys. the accuracy being about k0.05 wt pct. At high temperatures, carbon-containing alloys react with alumina crucibles as follows: If the atmosphere in the splat-quenching furnace does not contain sufficient carbon monoxide the alloy can be depleted of carbon and contaminated with aluminum. Calculations and experimental observations showed that 50 to 100 torr CO partial pressure effectively blocked the above reaction in all the alloys investigated. The splat-quenching equipment in Figs. 1 and 2 provides for evacuation and back-filling with CO-Ar mixtures. The furnace is capable of operation up to 1650°C. and the gettering action of the graphite heating element reduces the oxygen partial pressure in the furnace atmosphere to below 10-5 torr, thus preventing oxidation of the specimens.

Jan 1, 1970

By T. L. Joseph

S. T. Killian (Johnstown, Pa.)—This is one of the finest papers I have read. Tying in stoichiometric calculations with furnace performance and practice is a step which had to be taken sooner or later. The noteworthy difference between Dr. Joseph's type of calculations and regular blast furnace calculations is that the Ib mol system is used as a basis. With the Ib mol system, weights, volumes, and chemical reactions can all be expressed in the same equation. In the paper, wind, ore, flux, and fuel are all expressed as lb or lb mols. Probably Dr. Joseph does not realize it, but the vague word coke appears only twice in the entire paper. Lb of C and Ib mols of C are followed through reactions but the word coke appears only as 1560 lb coke per ton of pig and 1700 lb of coke per ton of iron. Obviously in order to understand furnace reactions, the coke should be expressed as lb or lb mols of C. Furnaces can also be compared more easily. In some respects the paper is too thorough and too complete. The effects of the metalloids reduced into the iron upon the top gases represents a difference of less than 3 pct of the CO formed in the bosh. Due to the completeness of the calculations in relation to the CO/CO2 ratio, this was included and was necessary. However, the exclusion might have enabled more furnace men to follow the lb mol system of calculations through the blast furnace to a better degree. By considering only irons of similar analysis, this part of the calculations might have been omitted. However, if this had been done, total rewriting of the paper later would have been necessary in order to make the work complete as it is now. It also would not have been nearly as authoritative. In the paper, there appears the reaction: H2O + CO ? CO2 + H2 [I] Dr. Joseph states that he did not take this reaction into consideration in any calculations pertaining directly to the paper. The piobable reason- for this is that although it contains all the main reacting top gases except N2, it is rather inflexible since it is monomolecular in relation to each of the reacting gases and does not tie in with the gasification of C. Actually the reactions: H2O + C ? CO + H2 [2] 2H2O + C ? CO2 + H2 [31 and the solution loss reaction: CO2 + c ? 2c0 [41 tend to assume an equilibrium through the reaction: H2O + CO ? CO2 + H2 [I] which should be considered a balancing or equilibrium reaction. Reactions 2, 3 and 4 permit furnace conditions to balance with the CO/CO2 ratio and H2 formation. They tie in with the solution loss. Reaction 1 unites them chemically. Probably the best calculation to make at this time would be to try to find the relative importance of the CO2 from the flux and the H2 in the dilution on an actual furnace gas analysis. For this purpose the Dob-scha-Carnegie-Illinois paper—"Effect of Sized and Sintered Mesabi Iron Ores On Blast Furnace Performance" is chosen. This paper was presented before the blast furnace section of the AIME in 1948. This represents the best large scale furnace operation available to me. Unfortunately the changes were brought about by beneficiation of the burden and not by changes on one burden. In choosing the basis for the calculation in relation to the furnace, 100 mols of dry top sgas is chosen. This leaves something to be desired inasmuch as the nitrogen basis is changing but I believe it will be better understood than any other type and it is the easiest to use.

Jan 1, 1952

By AIME AIME

WILBER JUDSON is one of that fairly large group of mining engineers that graduated at an Eastern college, worked his way up in various jobs in the West and in the Latin-American countries, and finally came to New York as an administrative officer of a large mining company. Since coming to New York he has been a loyal friend and counselor of the A.I.M.E., and is now serving a second term as one of its Directors, his first term covering the period 1935-1938. Mr. Judson was born in the capital city of Michigan on July 26, 1880. Probably it was his roving spirit rather than professorial urging that was responsible for the fact that four colleges were responsible for his education: Northwestern, University of Michigan, Harvard (S.B., 1901), and the Michigan College of Mines (graduate study). In his first ten years of professional work he might have been found serving as mine foreman at Catamarca in the Argentine, as superintendent of the Inter Ocean mine at Sunshine, Colo.. as foreman for the Cerro Prieto, Magdalena, Sonora, as superintendent of the Hudson Iron Co. in New York, or as manager of the Dolores mine in Chihuahua for the Mines Co. of America, or in Spain, or in Panama.

Jan 1, 1942

Oct. 8-13, 1917 COMMITTEE ON ARRANGEMENTS H. A. BUEHLER, Chairman, W. E. McCOURT, Secretary, C. J. ADAMI, Southeastern, J. A. CASELTON, Entertainment, F. W. DEWOLF, Book, , E. F. GOLTRA, Finance, L. L. HUTCHISON, Tulsa, E. McAULIFFE, Transportation, P. N. MOORS, Reception, MRS. P. N. MOORE, Ladies, J. D. ROBERTSON, Publicity, VICTOR RAKOWSKI, Joplin., H. A. WHEELER, Excursions, A. THACHER.

Jan 7, 1917

By B. L. Averbach, M. F. Comerford, M. B. Rough

The volume fraction of ß phase was determined in a Ti-6Al-4V alloy by measurements of integrated diffraction intensities. The (0002), and (100)ß diffraction lines were chosen because this combination minimizes the errors resulting from preferred orientation. The difficulties arising from fluorescence radiation were eliminated by use of a diffracted beam monochromator. A specimen quenched from 1475OF (800°C) contained approximately 5 pct ß, but in specimens quenched from higher temperatures no ß was found. The ß phase formed during aging, and in specimens solution treated at 1570oF (855oC) approximately 10 pct ß was present after aging at 1000°F (540°C) for 24 hr. This ß appears to form by decomposition of martensitic a'. ThE kinetics of the reactions which occur during the heat treatment of titanium alloys are complex ' and not completely understood. It has been proposed that hardening occurs in some alloys' on aging by the precipitation of a transition phase w followed by the formation of the stable a and ß phases. It has been proposed for other alloys2 that the a' marten-site decomposes by precipitating finely dispersed a particles. Most investigations have been hampered by the difficulties of determining quantitatively the amounts of the various phases present. This paper is concerned with the measurement of the amount of ß phase by an X-ray method, similar to one developed for the determination of retained austenite. The principal new feature was the use of a mono-chromator in the diffracted beam in order to reduce the fluorescence arising from the sample. EXPERIMENTAL PROCEDURE The experiments were carried out on an alloy of nominal composition Ti-6Al-4V (actual weight percentages: 6.2 Al, 4.1 V, 0.02 Mn, 0.17 Fe, 0.005 H, 0.03 C, and 0.02 N). The material was received as 5/8-in.-diam centerless ground rods in the annealed condition. The heat treatments were carried out in a vacuum of approximately 0.03µHg. The X-ray intensity measurements were made on 3/8-in. thick discs. The surface was prepared by grinding off about 0.060 in. and electropolishing in a solution af 60 ml (70 to 72 pct) perchloric acid in 1000 ml glacial acetic acid with a current density of 0.5 amp per sq cm.q The X-ray determination is based on the proportionality of the diffracted intensity of each line to the volume fraction of the corresponding phase. In calculating the intensities for a powder sample it is assumed that a large number of grains con- tributes to the diffracted intensity and that the grains are oriented at random. The presence of preferred orientation introduces serious errors in the relative intensities. The material used in this investigation exhibited a strong preferred orientation, which could not be removed by heat treatment. Other investigators have also found that preferred orientation may be retained after phase transformations. Glen and pugh5 performed a detailed analysis of the randomness expected after several allotropic transformations, but stated that this is not observed. Burgers,6 and Burgers and Ploos van Amstel,7 found that, in zirconium, the original orientation is retained after two phase transformations. Newkirk and Geisler8 observed similar behavior in titanium. On the basis of this evidence, it appears that, in the absence of plastic deformation, textures present in annealed titanium alloys are retained. Heating an a-ß alloy to the all-ß region and subsequent cooling to room temperature do not make the orientation of the mar-tensite different from that of the original a phase. In the present investigation it was possible to take advantage of the crystallographic relationships involved in the martensitic transformation to minimize the errors associated with preferred orientation. The relative orientation for titaniu-m marten-site9 takes the form (0001), 11 (110)ß; [1120], 11 [lll]ß. The same relationship has been proposed for zirconium' and certain titanium-base alloys.10-12 Additional sets of approximately parallel planes have been determined for titanium-nickel alloys." The influence of preferred orientation can be minimized by comparing intensities from parallel planes in the two related phases. If it is assumed that each family of planes in a given phase is equally well populated, the effect of preferred orientation can be eliminated by using the normal multiplicity for the family of planes since each set of parallel planes is equally preferred for any orientation of the sample relative to the X-ray beam. The most suitable combination of reflections in the Ti-6A1-4V alloy appeared to be (0002), and (110)ß It must be recognized that the ß formed during aging of the Ti-6A1-4V alloy is a precipitate rather

Jan 1, 1960

By Klaus-Peter M. Hanke

INTRODUCTION In early 1979 Jim Walter Resources, Inc. (JWR) of Brookwood, Alabama approached TMCI Construction, Inc (TMCI) to make a proposal on a program that involved the sinking of up to 10 ventilation shafts of approximately 6.7 m (22 ft) diameter and ranging in depth from 500 to 700 m (1650 to 2300 ft) for the JWR coal mines in Alabama. At this time TMCI was already constructing the first spiral underground bunker (capacity 2000 tons) in North America for the JWR organization at their No. 4 mine in Alabama. The TMCI proposal was based on the use of the mos modern large diameter shaft boring machine rather than sinking the shafts using the conventional drill blast-muck technique. The proposal was made based o: the experiences by the parent company, Thyssen Schachtbau, which has been using this type of machin in Germany for shaft boring since 1971. As a result of the TMCI proposal JWR issued a purchase order to TMCI for the construction of four 6.7 m (22 ft) diameter, concrete lined, unfurnished ventilation shafts ranging in depth from 500 to 700 (1650 to 2300 ft). An order was thus placed with WIRTH Machinen- and Bohrgeraete Fabrik GmbH, in Germany for the manufacture of a model 650/850 E/Sch "Schachtbohrmaschine" (Vertical Shaft Borer = V-mole which arrived on site in Alabama in early 1981. The first V-mole GSB 450/500 was introduced in Germany in 1971 and was capable of enlarging in one step a pre-drilled 1.2 m (4 ft) pilot hole to 4.5 - 5.0 m (14.7 - 16.4 ft). This machine has sunk 9 staple shafts and deepened one surface shaft for a total of 2360 m (7740 ft) of shafts. On the last shaft boring operation in 1978 the machine was converted as an experiment to drill without a pilot hol using a hydraulic pumping system to remove the cutting debris. A second generation machine, the SB VI 500/650, was introduced in 1977 for enlarging the pilot hole to a range of 5.0 - 6.5 m (16.4 - 21.3 ft) diameter. This machine is still in operation and has already drilled well over 2000 m (6500 ft) of shaft. The third generation of V-mole, the SB VII 650/85( for diameters from 6.5 to 8.5 m (21.3 to 27.9 ft) was: commissioned in May 1980 and has been used for two surface shaft deepenings totalling 606 m (1990 ft) with another scheduled for 1982. The main advantages favouring the use of such V-moles were identified as: 1) A reduction in manpower to the crew required in a conventional shaft sinking operation. 2) A considerable reduction in time to complete a shaft compared to conventional techniques. 3) The use of the V-mole eliminates many of the hazards encountered in conventional sinking. Based on the successful performance of the first three V-moles in Germany, Thyssen Schachtbau decided to employ this principle abroad. In 1980 a second machine of the third generation was built and is now operated by TMCI Construction, Inc. in Alabama. The first shaft was completed at the end of 1981 and this paper describes the method of operation including some unique aspects not attempted on prior V-mole operations and some of the statistics arising out of the experiences during the first shaft boring operation. THE NO. 7 MINE FAN SHAFT SITE Jim Walter Resources, Inc. was formed in 1970 to exploit the coal field in Alabama on the southern tip of the Appalachian coal field. The coal reserves amount to around 650 million tons of mainly good quality coking coal of which about 350 million tons are to be extracted over the next 30 years. Shaft sinking and preparatory work began in 1972, and at present 6 mines are producing around 5.4 million t.p.a. Annual production is to expand to 10 million t.p.a. as soon as possible, and the ventilation shafts to be sunk by TMCI play a vital role towards attaining this goal. The first shaft site is located at the No.7 mine, near Brookwood, Alabama. The actual location of the shaft relative to the production shafts is shown on the mine plan (Fig. 1), which also shows the room-and-pillar extraction system used at present. The mine plan further shows the conveyor route used for the muck removal. The geological survey showed that the strata consisted of horizontal layers of mainly sandstone, sandy shale and shale interspersed with several coal seams. The seam being extracted at the No. 7 mine is a combined seam made up of the Blue Creek and Mary Lee seams at a depth of 513 m (1682 ft) and having an average seam thickness of about 2 m (6 ft). At the beginning of September 1980 the surface site preparation and pre-grouting work was completed by JWR, and TMCI was able to commence with Stage I of the shaft sinking program - the drilling of the pilot hole.

Jan 1, 1982

By C. M. Brinckerhoff

Safety work in mining at the Andes Copper Mining Company, Potrerillos, Chile, is divided into three parts: (1) accident prevention, (2) fire prevention and protection, and (3) silicosis prevention and control. In the company's operations a steady campaign has been waged to reduce accidents and silicosis, and to prevent fires. In the following pages the safety record for the past twelve years will be examined and the methods explained by which the accident rate was reduced. Table 1 contains yearly data pertaining to the scale of the mining operations and the accident record. Block caving is used for all ore production and the tonnage mined has aver- aged 30,000 short tons per day for the past seven years. Table 2 classifies 44 fatal accidents which have occurred since 1935. The leading causes of accidental death are transportation of ore and use of explosives, followed in order by per- sons falling, falls of ground, and by asphyxiation. In the case of serious accidents, however, the greatest cause is falls of ground, followed, in turn, by ore

Jan 1, 1949

By Meguru Nagamori

DURING the smelting of the sulfide ores of copper, nickel, and certain other metals, a matte phase is formed. For a better understanding of the physico-chemical properties of mattes, binary systems such as Cu-S, Ni-S, Fe-S, and so forth, should be studied, especially in the vicinity of liquid compounds such as Cu2S, Ni3S2, FeS, and so forth. These compounds are relatively stable in the solid state although they can exhibit appreciable deviations from stoichiometry. With small deviations from stoichiometry there are large changes in the activity of both sulfur and metal this is a characteristic of both solid and liquid sul-fides near the stoichiometric compositions. In the vicinityof molten Cu2S,1 for instance, the activity of sulfur increases about 100 times for a 0.012 increase in the mole fraction of sulfur and, correspondingly, the activity of copper decreases greatly. In this sens the minor deviations from stoichiometry should be carefully taken into account in studies of such metal-sulfur melts. Metal-sulfur melts may be considered to have properties intermediate between metallic solutions and molten salts, i.e., neither entirely metallic nor entirely ionic. The radius of the ion sZ- is 1.84 as compared with 1.04? for a single bond covalent s.2 It is therefore inferred that when the sulfur is more ionic its partial molar volume is larger, although metal-metal, metal-sulfur, and sulfur-sulfur interactions may bring about further complexities. Thus, it is to be expected that the molar volumes, which are derived from density-composition relations, will help in resolving the structure of the melts. In this study the maximum bubble pressure method with bubbling gases of H2, H2S, and Ar, .was employed to measure the density. EXPERIMENTAL Materials. Silver of 99.95 pct purity was melted in an alumina crucible and hydrogen gas was then bubbled through the liquid for the deoxidation. In preparation of Cu2S, electrolytic copper powder (>99.9 pct Cu) was mixed with precipitated sulfur and heated to 1200°C in an alumina crucible under a hydrogen atmosphere. Mixtures having the approximate compositions FeS and Ni3S2 were prepared by heating reagent grade electrolytic iron or reduced nickel powder with precipitated sulfur under a hydrogen atmosphere. The H2S gas was of 98.5 pct purity, the impurities being mostly CO2 and CS2 which hardly contaminate the melts. Apparatus. The crucible system is shown schematically in Fig. 1. To minimize the variation of melt composition during a density measurement, the apparatus was designed in such a way that either Ar, H2, H2S, or mixtures of these gases could be used as the bubbling gas. When the melt had a high partial pressure of sulfur, H2S gas was used. When the partial pressure of sulfur was so low that oxygen might dissolve in the melt, the use of H2 was preferred. In intermediate cases, argon or mixtures of H2-H2S were used. Density of Dibutylphtalate. Dibutylphtalate was used as the manometer fluid. Relative to distilled water, the density of the dibutylphtalate, pdib g per cc, was measured and found to be: pdib (25°C) = 1.046 i 0.002. With the use of the temperature coefficient reported by Kemppinen and Gokcen,3 the following value was

Jan 1, 1970