Search Documents

By Wayne A. McCurdy

For the third consecutive year, predicted increases in coal production and consumption failed to materialize. Production of bituminous, sub-bituminous and lignite coal for 1961 was estimated by the U.S. Bureau of Mines at 400 million tons, a drop of 15,- 512,000 tons from the 1960 figure. Anthracite production for the year was 17.8 million tons compared to 18.8 million tons produced in 1960. Consumption figures are expected to show a proportionate decline. Of coal's major markets, only electric utilities showed an increase-and even here the increase of approximately 2% was smaller than had been expected. Major cause of relatively low consumption was a decrease of more than 20% in the use of metallurgical coal for making coke. Reductions of lesser importance were registered in general industrial, retail, and export markets.

Jan 2, 1962

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information' will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 2, 1918

By J. E. House, J. L. Drobnick, R. R. Swanson, D. W. Agers

Since the commercial acceptance of the liquid ion exchange process in the mineral processing industry, it has been predicted that eventually the hydrometallurgist would have a wide selection of commercially available chemical reagents to make separations efficiently and economically of virtually all metals in solution under a wide range of conditions. Several years ago, General Mills began a research and development program to determine if it were possible to develop a reagent to extract a specific metallic ion from solution at a cost that would allow large scale commercial application. A giant step toward reaching this objective was announced in late 1963, when development quantities of LIX®-63 reagent, a highly selective reagent for the extraction of copper, were first offered to industry. The properties of this reagent were de- scribed in a previous paper.1

Jan 12, 1965

By M. D. Cooper

Production of both anthracite and bituminous coal in 1954 was about 16 pct below 1953. Estimates on Dec. 1, 1954, indicated 27 million tons of anthracite and 385 million tons of bituminous. Decline in production was due principally to lower demand by the steel industry and the railroads, although competition from other fuels also affected coal. The year was notable for vigorous effort by the coal industry to promote the use of its product. A Cabinet Committee on Energy Supplies and Resources Policy and an Interdepartmental Committee on the Soft Coal Industry were set up by the Administration in Washington. A Governors' Fuel Conference was also organized.

Jan 3, 1955

By G. M. Ritcey

The design of the plant facilities together with the necessary equipment required for the operation is at an optimum only for the specified plant with its peculiar priorities and preferences. Because many alternatives in design are possible to suit a particular plant, each plant designer and contractor must choose carefully in the selection of the site, design and choice of materials of construction, as well as the type of equipment necessary for the process. Basic factors as efficiency, dependability, simplicity, and safety must be considered early in the construction; while the choice of equipment, materials of construction, possible corrosion problems, automation, maintenance, effluents disposal and tailings dam construction can greatly affect the plant costs. While existing plants are in operation, the know-how gained from the operating experience of those plants can be invaluable in the new plant planning, design, and construction.

Jan 1, 1978

By A. J. W. Headlee

RECENT interest in germanium centers around its use as a semi-conductor of electricity in electronic devices. It is generally believed that germanium transistors, diodes, triodes, photocells, and rectifiers will largely replace the present-day vacuum tubes. The germanium electronic devices are much smaller, lighter, and more resistant to shock, and they require only a small fraction of current required for conventional devices. Hence only a small amount of heat is given off by the equipment. This development will require many times the quantity of germanium now being produced, which in 1948 was approximately 1000 lb1 and was obtained almost entirely from zinc ores in Missouri, Kansas, and Oklahoma. No one knows with certainty what the demand will be for germanium by 1956. It may be 40,000 lb.1 Known concentrations in zinc ores are not sufficient to

Jan 10, 1953

By Thomas Connolly

The Homestake Mine is situated in the northern portion of the Black Hills of South Dakota in a series of steeply dipping and highly folded Precambrian Rocks. The ore bodies are localized along plunging anticlinal and synclinal folds which are locally called "ledges." The gold bearing ore is confined mainly in the Homestake formation which is an iron-magnesium carbonate series of rocks. The individual ore bodies are pipe or lense-shaped zones which plunge 30º to 75º from the horizontal. These ore bodies range from 10 to 100 feet wide and 50 to 400 feet along the strike. Gold values are erratically distributed in a gangue consisting of cummingtonite schist, sideroplesite schist, quartz, pyrrhotite, arsenopyrite, chlorite schist and ankerite. Usually the ore bodies dip at 70° to 80º and often have folded shapes like "fish hooks" or "troughs." Ore grades must be determined by extensive sampling and all mining is based on assay control.

Jan 3, 1974

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, lnc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society, but the name has now been changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees, of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which have equal and undivided interests in. the property. The land and building cost two million dollars. During the year 1934, the Constitution and Bylaws

Jan 1, 1938

By Walter Riethmeier, Arthur J. Lynch

The future of plant design in mineral processing and extractive metallurgy is discussed in relation to present trends and the future need to build plants that will treat larger tonnages and lower grades of ore. The future equipment and plant design of crushing, grinding, screening, classification, flotation, magnetic concentration, gravity concentration, hydrometallurgy, thickening, filtration, tailings disposal, health, safety, environment, and materials of construction are discussed. Future plants are expected to follow upon present evolutionary trends. The impact of escalation, energy costs, and increased regulation of the industry is foreseen as a major influence on plant design.

Jan 1, 1978

Jan 1, 1936

J. B. MCGRAW, New York, N. Y. (written discussion*).-In Mr. Burke Baker's description of the process of the American Briquet Co., he speaks only of the attractive features, but every process which uses a compound or emulsified binder has certain undesirable features which must be considered. In making an emulsion, the success of which depends upon the introduction of the various ingredients at certain fixed temperatures and the complete intermixing of a soluble solution with an oil which has absolutely no affinity for it, considerable difficulty is found in keeping the various factors in strict accordance with the formula. To serve its purpose properly or, in other words, to be right for easy mixing with the coal, it should be of a certain predetermined density. Among the controlling factors of this ate the proportion of moisture contained and the temperature of the oil when introduced. If the latter is higher than intended, a greater proportion of moisture will be evaporated than is proper, and if the oil is not sufficiently hot the process of emulsification is retarded. These various factors can be controlled with more or less certainty where working in a laboratory or in a small experimental way, but when it is attempted on a large commercial scale, certain obstacles not otherwise apparent are likely to be encountered.

Jan 5, 1918

By Alexander Knoll, Dwight L. Baker

THE work herein reported shows that galena in certain organic solutions of fatty acids becomes coated with lead soaps, and that this coating is not only highly water-repellent but is also repellent to certain organic liquids, particularly those [ ] of high surface tension; i.e., nitrobenzene, diphenylmethane. WETTING PROPERTIES OF GALENA IN NONAQUEOUS FATTY ACID SOLUTIONS When a "captive bubble"' is withdrawn from a polished, plane galena surface under a nitrobenzene solution of stearic acid, the air bubble shows a decided tendency to "cling" to the mineral surface. The contact angle, therefore, was greater than zero, although it was not large enough to be measured quantitatively by the captive-bubble method.* [ ] When pure nitrobenzene was substituted for the nitrobenzene-stearic acid solution, no clinging of the bubble was observed; viz., contact angle = zero. Although the contact angle developed in air-galena-nitrobenzene-fatty acid solution was small, the organic solvent repellency of the galena surface was great enough to enable good recovery in a laboratory flotation cell.2 In Table I are given the results of flotation experiments using several different fatty acids dissolved in nitrobenzene.

Jan 1, 1941

By M. D. Everell

A study has been made of the relationships between grinding selection functions and physical properties of rocks, particularly the failure loads of irregular particles and the compressive and tensile strengths of large regular specimens. The rocks used were limestones of various structures and impurity contents, a carbonatite, and a high-purity crystallized calcite. The selection functions were obtained from carefully performed grinding experiments on selected narrow size ranges in various grinding machines-a laboratory batch ball mill, a Hard grove grindability machine, and a mill of the type suggested by Yang, Mempel, and Fuerstenau. The specific rates of breakage during milling and the failure loads of irregular specimens correlated well for the rocks studied. The testing of irregular particles is suggested as a means of predicting the behavior of commercial mills.

Jan 1, 1973

By Chi-Yuen Wang, Chaw-Long Chu

The time-dependent volumetric constitutive relation for a San Andreas fault gouge and a consolidated kaolinite are experimentally determined at confining pressures to 200 Mpa, under creep condition and at ultrasonic frequency. At any given pressure, the bulk modulus determined at 1 Mhz frequency is identical to the "elastic" modulus determined at a stepwise change of pressure. After the pressure change, there occur a time-dependent change of volume and thus the effective bulk modulus. The constitutive relations may be modeled by a standard linear viscoelastic medium with pressure-dependent moduli and viscosity. For the San Andreas fault gouge, viscosity increases from 2x10 13 poise, at 17 Mpa, and 10 14 poise, at 100 Mpa. For kaolinite sample, the corresponding values are 3x10 12 poise and 10 13 poise. These results imply that both stress and pore pressure in fault zones may show time-dependent variations in response to a change of state of stress, such as that occurring after an earthquake.

Jan 1, 1982

By D. J. Spottiswood

The control of thickener operation has proved difficult due to a lack of understanding of thickener operation and the long retention times involved. This is particularly true in counter current decantation circuits where the interact ion between thickeners further complicates the control problem. In this paper, the control aims and controlable variables are identified, and the development of a control system is discussed. Models of the sedimentation process, as carried out in thickeners, have been primarily aimed at thickener design. These models are examined and utilized in a dynamic model development. A preliminary dynamic model of the thickener operation is discussed here with relation to control application and its use in CCD circuit control examined.

Jan 1, 1984

By J. Donald Graham, John G. Kuhn

The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an ore body, no more and no less. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. The method for controlling development drilling programs to be described was developed during the latter part of a major development drilling project at the Christmas mine of Inspiration Consolidated Copper Co. in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous ore bodies of the porphyry-copper type would be the most likely candidates for application of the technique. Discontinuous ore bodies would not be amenable. The method is based on the measurement of the linear correlation between the spatial distribution of two sets

Jan 1, 1973

By J. D. Dixon

Procedures are given for calculating stresses in underground tunnel supports which accounts both for the structural behavior of the support and that of the adjacent rock mass. Stresses in the support are caused by service loads and rock reactions. Service loads are due to rock pressures, hydrostatic and hydraulic pressures, selfweight of the support, or other utilitarian-type loads. Rock reactions, equal and opposite those in the support, are due to the deformational interaction that results as service loads deform the tunnel support against the adjacent rock mass. The procedures developed for solving this problem are an application of matrix structural analysis. The principles involved in this method allow for the consideration of the deformable characteristics of most tunnel support systems and an iterative solution procedure is applied to determine the areas of support-rock interaction. Numerical results of example problems are given.

Jan 1, 1972

By R. D. MacDonald

The search for metalliferrous deposits in the Labrador-Ungava Trough of Canada dates from 1929 when non-ferrous minerals were the main quest of prospectors in this area. Many gossans, resulting from the oxidation of sulfides, were located and examined but none of these led to any orebodies of commercial value. However, such investigations did much to arouse interest in this area and fostered further mapping and prospecting. Since this early period in the history of prospecting in the Trough, the presence of iron ore deposits and potential iron producing sites has commanded the center of attention of exploration personnel. The iron-bearing rocks of southwestern Labrador have in recent years come into prominence as possible sources of iron ore of the beneficiation type. Exploration and development work has been carried on in concession areas granted by the Newfoundland Government to the Labrador Mining and Exploration Co. Ltd. and to the Newfoundland and Labrador Corp. In the course of evaluating its holdings in the Wabush Lake area (Fig. l), Labrador Mining and Exploration Co. has conducted geological, geophysical and diamond drilling programs.

Jan 10, 1960

By Cornelius F. Kelley

SEVENTY-FIVE years ago, in Wilkes-Barre, Pennsylvania, 22 men of vision banded together to initiate this great organization. Ideals and emotions mingled and united in the declaration of a twofold purpose: first, the more economic production of minerals and metals, and second, the promotion of greater safety and welfare for each man so employed-tacit recognition of the inseparability of humanitarian and utilitarian concepts of world progress. The members and honorary members then, as now, were mining engineers and associates from allied walks of life. Under the able guidance of David Thomas, our first president and outstanding ironmaster of the time, there were elected 46 members and associates, and the foundations of the Institute were laid. Conceived in a turbulent postwar era, the problems then faced had some similarity to those we face in this time of war-bashed uncertainty. With a Civil War behind them and once again dedicated to a spirit of national endeavor, they surveyed the landscape, then surged ahead toward a beckoning industrial horizon. That effort has never been relaxed. Poised upon the threshold of a new century, rancher, banker, engineer and businessman paused to contemplate and evaluate his natural endowments. Surrounded by immeasurable God-given wealth, necessity inspired

Jan 1, 1947

By C. F. Tolman

Discussion of the paper of C. F. TOLMAN, JR., presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 401 to 433. Louis C. GRATON, Cambridge, Mass.-Of particular interest at this time is any paper that deals with chalcocite, the characteristic product of secondary enrichment and the copper mineral of greatest commercial importance, and that seeks to aid in the distinction between primary and secondary chalcocite-a distinction of much scientific and practical importance but one which thus far it has proved difficult to draw. The present paper on this subject by Professor Tolman, like the ,many preceding it which he and his colleagues at Stanford have published in the last couple of years, contains much of interest and suggestiveness. Without endeavoring at this time to review or comment upon Professor Tolman's conclusions in detail, I may say that many of them are in accord with the findings that my associates and I have been accumulating in the course of studying secondary enrichment in many of the copper deposits of the country. On the other hand, it goes without saying that in this comparatively new field of research or, at least, a field in which

Jan 5, 1916