Search Documents

By Howard Clarke, Cyril Stanley Smith, Clarence Zener

THE importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature." PREPARATIONS OF SPECIMENS In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal frictions is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm. Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tensiontesting machine, using special grips10 to ensure axial application of the load. The rate

Jan 1, 1941

By Joseph M. Dawson

Although there was a very great increase in drilling activity along the fault line of south Texas during 1937 as compared with the previous three or four years, and although seven new fields were discovered, it cannot be said that any major development of importance took place. There were slightly over 550 completions during 1937, of which nearly 350 were oil wells as compared with some 275 the preceding year, of which 169 were oil wells. This increase in drilling activity was occasioned almost entirely by the greater interest in and development of Austin chalk production, principally in Caldwell, Guadalupe and Bastrop Counties. Seven fields were found, of which a brief description is given in Table 3. None has as yet assumed anything of major importance, and it is doubtful whether any will be classified as major discoveries through further development. Two were producing from the Edwards limestone, one from serpentine and the other four from the Austin chalk; the latter may be classified as extremely erratic in nature. The major discouraging feature of the year was the rise and subsequent fall of interest and importance of Austin chalk production. Many new operators came into this district to drill and produce Austin chalk oil toward the first of the year, but in the latter months the production decline from this formation was so rapid and the production so erratic that drilling operations fell off materially and interest largely abated. This was particularly true of the Branyon field in Caldwell County, and the same statement is applicable to the Pearsall field, Frio County. The latter field, covering some 5000 acres and owned and controlled entirely by the Amerada and Rycade, had early completions from the Austin chalk as high as 22,000 bbl. per day. The decline was extremely rapid and the maintained production from 17 wells is only around 700 bbl. per day after a total recovery of less than one-half million barrels. Present estimates of recoverable oil from Chalk vary from 2000 to 5000 bbl. per acre. A new process for the completion of producing wells from the Edwards limestone, particularly applicable to old producing areas, was developed, in that the penetration of the Edwards lime in drilled wells is now only 1 or 2 ft. as compared to between 15 and 75 ft. in wells drilled several years ago. Many new wells have been drilled in old Edwards lime producing

Jan 1, 1938

By T. B. Brooks

THE iron ores of the Marquette region are mostly extracted in open excavations ; hence the process is more properly quarrying. Several attempts at underground work have been made, which have not, on the whole, been successful. The Edwards mine has been almost entirely wrought by candle-light. The slate ore pit, No. 1, of the New England mine, is now worked in the same way, as is also the Pioneer furnace pit of the Jackson mine. The Champion mine was opened systematically for underground work, with two levels, 60 feet apart, and three shafts at distances apart along the bed. of 200 feet; but this idea has been practically abandoned, the greater part of the ore in that mine being now taken out in open pits. Several other mines have occasionally worked underground stopes, but only temporarily; if such stopes could not be opened out to day-light, they have usually been abandoned. In brief, it may be said that no considerable amount of ore has as yet (1870).been extracted underground in the region, and of that so mined very little has been taken out at a profit; and I may add that it seems to be the belief of the most experienced mining men that this state of things will hold for some time to come for reasons which will appear. Nearly the same remarks may be applied to the mines of the Iron Mountain region, Missouri, the ores of which are very similar in character to those of Marquette. Some of the New York and New Jersey magnetic deposits are wrought open, but this is the exception, underground mining there being the rule. The following brief sketch of the geological structure of the Marquette deposits will indicate some advantages of the method of mining employed. The iron-bearing (Huronian) series of rocks, are stratified beds, the principal ore formation being overlaid by a quartzite, and underlaid by a diorite, or greenstone. This ore formation is made up, first, of pure ore ; second, of a mixed ore" (i. e., banded * A second part of this paper was read before the American Society of Civil Engineers. Both papers are embraced in Chapter IX, Part I, Vol. II, Geological Survey of Michigan.

Jan 1, 1873

By Ralph Hultgren, David W. Mitchell

MAGNESIUM alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600° to 1700°F while the casting temperature, which depends upon the mold shape, is usually 200° to 300°F lower. The process of superheating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported' that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results.2 As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted" Project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. MATERIALS AND METHODS The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesium used in these alloys was of both carbothermic3 and electrolytic4 origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200' to 1250°F., portions of approximately one pound each were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21† covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F for 15 min., then cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

By M. D. Hassialis, A. F. Taggart

ark' observed some years ago that collector-coating reactions with xanthates and with fatty acids clearly follow paths parallel to those prescribed by the familiar mass-action law for reactions in dilute solutions. He proposed, therefore, the logical hypothesis that they are governed by the solubility-product principle. However, he went astray in the application of his proposal to collector coating by overlooking the fact that coating involves a heterogeneous reaction. A mistaken concept of the meaning of the word adsorption also entered. Wark thought that the concentration of metallic ion that must be used in setting up the solubility-product equation for the coating reaction was that which could be obtained by solution of the mineral. Since this is very low for sulphide ores, and since the amount of the collector ion necessary for coating produces an extremely low concentration, the resulting ion-concentration product, under conditions when coating occurs, is much lower than that which would indicate a saturated solution of the collector-coating compound. Hence he was forced to the position that the solubility product governing the coating is much smaller than the standard solubility product. To justify this position it was necessary to postulate a coating mechanism that did not obey the ordinary laws of chemical reaction. This Wark did by adopting the concept that adsorption is a property of matter, rather than merely a more or less ephemeral local concentration thereof. Thus he says (p. 142 of ref. I): "Adsorption is not a purely physical property of the solid surface, for the specific nature of the adsorbed molecule or ion is important." The result was that he destroyed the great potential utility of his postulate by tying it to this erroneous concept in the words (pp. 142, 143): "It will be obvious that the adsorption solubility product is less than the normal solubility product." The writers have found quantitatively in the case of galena and potassium ethyl xanthate, and semiquantitatively in the case of covellite and the same collector, that the coating reaction does follow the mass-action law to the extent that coating occurs when the ordinary solubility product of the coating compound is exceeded, and that coating does not take place under the reverse conditions. In the course of the investigation leading to the establishment of this fact it was necessary to work with xanthate concentrations so low (down to 0.0004 mg. per liter), that very long conditioning times, and bubble-contact times of as much as 16 hr. were necessary sometimes to follow the reactions. The results have led to some illuminating conclusions as to necessary collector concentrations in normal flotation operations, and the action of the frothing agent in connection therewith' The experimental work comprised accurate determination of the standard solubility product of lead ethyl xanthate, development of a much less laborious

Jan 1, 1947

By M. D. Hassialis, A. F. Taggart

ark' observed some years ago that collector-coating reactions with xanthates and with fatty acids clearly follow paths parallel to those prescribed by the familiar mass-action law for reactions in dilute solutions. He proposed, therefore, the logical hypothesis that they are governed by the solubility-product principle. However, he went astray in the application of his proposal to collector coating by overlooking the fact that coating involves a heterogeneous reaction. A mistaken concept of the meaning of the word adsorption also entered. Wark thought that the concentration of metallic ion that must be used in setting up the solubility-product equation for the coating reaction was that which could be obtained by solution of the mineral. Since this is very low for sulphide ores, and since the amount of the collector ion necessary for coating produces an extremely low concentration, the resulting ion-concentration product, under conditions when coating occurs, is much lower than that which would indicate a saturated solution of the collector-coating compound. Hence he was forced to the position that the solubility product governing the coating is much smaller than the standard solubility product. To justify this position it was necessary to postulate a coating mechanism that did not obey the ordinary laws of chemical reaction. This Wark did by adopting the concept that adsorption is a property of matter, rather than merely a more or less ephemeral local concentration thereof. Thus he says (p. 142 of ref. I): "Adsorption is not a purely physical property of the solid surface, for the specific nature of the adsorbed molecule or ion is important." The result was that he destroyed the great potential utility of his postulate by tying it to this erroneous concept in the words (pp. 142, 143): "It will be obvious that the adsorption solubility product is less than the normal solubility product." The writers have found quantitatively in the case of galena and potassium ethyl xanthate, and semiquantitatively in the case of covellite and the same collector, that the coating reaction does follow the mass-action law to the extent that coating occurs when the ordinary solubility product of the coating compound is exceeded, and that coating does not take place under the reverse conditions. In the course of the investigation leading to the establishment of this fact it was necessary to work with xanthate concentrations so low (down to 0.0004 mg. per liter), that very long conditioning times, and bubble-contact times of as much as 16 hr. were necessary sometimes to follow the reactions. The results have led to some illuminating conclusions as to necessary collector concentrations in normal flotation operations, and the action of the frothing agent in connection therewith' The experimental work comprised accurate determination of the standard solubility product of lead ethyl xanthate, development of a much less laborious

Jan 1, 1947

By L. B. Ticknor, M. B. Bever

An isothermal calorimeter suitable for measurements of heats of solution in liquid tin as solvent is described. Measurements of the heats of solution of gold, silver, copper, and a gold-silver alloy are reported. The heat of formation of this gold-silver alloy is also reported. HEATS of solution in liquids can be determined directly, but few such data have been published for metals as solvents. Knowledge of heats of solution is desirable because it contributes to the general understanding of energy relations in metallic solutions. Thermochemical measurements of this type also furnish answers to specific problems: For example, from the heats of solution of an alloy and of a mixture of its constituent elements in a given solvent, the heat of formation of the alloy may be found. Similarly, differences in the energy content of samples of the same metal in two different states, such as the annealed and cold worked states, may be determined. In the work reported here, gold, silver, and an alloy of gold and silver were dissolved in liquid tin at 240°C and gold, silver, and copper were dissolved in tin at 300 °C. The experiments yielded the heats of solution of these metals in tin. The heat of formation of the gold-silver alloy was also determined. The same calorimetric method is being used to measure the energy stored in metals during cold working and preliminary results have been published.' Equipment and Experimental Procedure The isothermal calorimeter used in this work, Fig. 1, consisted of a Dewar flask completely immersed in a constant-temperature salt bath. A long neck provided space for thermocouple leads and a stirrer shaft and permitted the injection of solute samples. The metal bath in the calorimeter flask was stirred at about 100 rpm by a small glass impeller driven by a constant-speed motor. The shaft of the stirrer passed through a Wilson vacuum seal.2 All measurements were made under vacuum in order to eliminate temperature disturbances resulting from gas convection and to prevent the oxidation of tin. The calorimeter flask was joined by an all-glass connecting line to a gas-control system which made possible the use of a protective atmosphere of deoxidized and dried hydrogen. At the operating temperature of the calorimeter tin oxide was not reduced by hydrogen, presumably because the reaction rate was too slow. Part of the closed system was a removable side tube through which the solute sample could be introduced and in which it was held at a temperature of 0°C prior to injection into the metal bath. The salt bath containing a mixture of sodium, lithium, and potassium nitrates was similar to that described by Beattie3 and was equipped with a stir-

Jan 1, 1953

By Albert E. Reed

THE development of the modern high-speed vibrating screen, together with the increasing availability of long-lasting stainless-steel screen cloth for relatively fine-mesh separations, means that more screen circuits will be used in the future. It seems pertinent therefore to examine a few characteristics of screen-circuit products, and especially the points of difference as compared with products of classifier circuits. The most noticeable change that takes place when substituting screening for classification in a grinding circuit is a substantial drop in the circulating load, owing to the greater ease with which the "fines" leave the circuit. Where circulating loads of 500 to 600 per cent are considered fairly normal in classifier grinding circuits, the grinding circuit equipped with screens for equivalent work will have a circulating load of only 20 to 75 per cent. As a result, the products of screen circuits will show a minimum of overgrinding or sliming as compared with a classifier circuit. The desirability of this characteristic will naturally vary according to the metallurgical requirement in each case. Because screen separations make a sharper division according to particle size, the products of screen circuits can be expected to show greater crowding of particles near the point of separation. These changes in product characteristics are so important that other factors, both in the grinding and concentration processes must be adjusted if the operator is to take full advantage of the increased tonnages and higher efficiencies available to him through the use of the screen circuit. One factor that too often is overlooked when changing to screen circuits is the importance of adjusting the ball-mill or rod-mill charge, to compensate for: (I) increased tonnage of new feed, (2) decreased circulating load, or (3) more granular character of feed. These same factors should also be taken into consideration for their effect on the various types of concentration or flotation equipment that may follow the screen circuit. Over a period of years, this equipment has generally been designed and adjusted to the product of the classifier, therefore it seems obvious that some research on the adjustment and adaptation of concentrating and flotation equipment to screen-circuit products will be most profitable to the operators. To illustrate the points mentioned above, the results from three recent installations follow, with data on the comparative characteristics of screen and classifier circuits. A range of separation from 10 to 48 mesh has been chosen, using two general types of screening equipment and two types of classifiers. The first of the installations of which the results are to be examined is that of an iron-ore installation where eastern magnetite was being concentrated prior to sintering. Fig. I shows the original grinding circuit, using classification, while Fig. 2 shows the same circuit equipped with a

Jan 1, 1945

By Leland L. Mink, Roy E. Williams, C. Daniel Kealy

The passage by Congress of Public Law 92-500 (the 1972 Water Pollution Control Act amendment) has placed a new emphasis on the need for methods to minimize the escape of water from tailings ponds. Presumably tailings pond seepage will fall under the jurisdiction of the act. This paper is designed to explain some of the problems caused by leakage from tailings ponds and to present a method by which leakage can be minimized if not eliminated. Ground-water pollution in one case studied by the authors results from leaching of old jig tailings that are intermixed with the upper part of a sand and gravel aquifer. Anomalous concentrations of zinc, lead, and cadmium occur in ground water and soil samples taken from the portion of the sand and gravel aquifer containing the old jig tailings. Analysis of water samples from a tailings pond located in the area indicates that the pond water is not the source of the heavy metal concentrations found in the down-gradient ground water. However, leakage from the pond and water from the pond's decant system combine with natural ground water to compound the problem by raising the water table into old jig tailings which cover the upper portion of the aquifer. The ground water which discharges from this aquifer causes a statistically significant decrease in the quality of the receiving stream water. The shallow ground water contains oxygen; therefore, corrective measures include lowering the water table to depths below the old jig tailings which cover the aquifer at ground level. This, in turn, implies elimination of ground-water recharge by subsurface leakage from the pond. A laboratory study and a mathematical model study have revealed that seepage from such ponds can be minimized by a carefully designed and managed peripheral tailings discharge system. The process involves maintaining the slime zone and the free-water surface near the center of the pond so that the slimes retard downward and semilateral movement of pond water. The free-water surface must not be allowed to extend out over the nonslime portion of the tailings during or after pond operation. Mathematical model output reveals that this method can hold the subsurface discharge rate to as little as 110 gpd per acre of pond water area. The technique should be applicable to any tailings pond system in which the loss via seepage of poor quality water must be minimized or where recharge of ground water by losses from a tailings pond must be minimized, regardless of the reason.

Jan 1, 1974

By Raymond Mancha

When calculating the pressure-volume characteristics of projected mine-ventilating circuits by orthodox methods, certain basic assumptions are required in order to employ the various available empirical data. It is assumed, for example, that the mine air is an incompressible fluid subjected to isothermal flow, an assumption sufficiently accurate for practical purposes since pressure and temperature differentials are small throughout the average circuit. A more erroneous assumption, however, is that all air is accounted for as it travels throughout the mine. No attempt is usually made to evaluate stopping leakage as it occurs; instead, the air volume required at the last crosscuts is assumed to enter the mine, travel the various intake air courses intact, sweep the workings and travel out by the return air courses to the point or points of exit from the mine. Actually, there is a leakage of air from intake to return at every stopping, the quantity of this leakage depending upon the tightness of the stopping and the pressure difference across the stopping. Unfortunately, a lack of empirical data and knowledge of the condition of individual stoppings makes an exact analysis of underground stopping leakage impossible. Generally, leakage is most severe through the old stoppings outbye the circuit. These are also subjected to higher pressure differences than the newer inbye stoppings. Therefore the circuit air volume diminishes at a decreasing rate progressing from outbye to inbye the circuit. Consider a simple mine circuit consisting of one intake and one return air course, each of equal and uniform section area and interconnected at regular intervals with crosscuts equipped with stoppings. At any point X inbye the circuit the air volume q on the intake air course equals that on the return air course and decreases with diminishing rate from outbye to inbye the circuit between the limits of Q1 completely outbye and Q completely inbye. Such a volume change is represented by curve a, Fig. I, which is computed with the aid of the equation q = Q1- (Q1- Q)(X + L)N. This equation results from the general algebraic equation of form q = k, — kXN after solving for kl and k with the knowledge that completely outbye X = o and q = QL, also completely inbye X = L and q = Q. Curves a, b and c, Fig. I, show values of q as ordinates versus values of X as abscissas, for values of N equal to 0.50, 1.00 and 2.00, respectively. Distribution of underground stopping 1eakage directly affects the air-volume distribution along the circuit, which in turn determines the circuit pressure gradient. To deliver any required air volume inbye a circuit or portion thereof requires a higher circuit-pressure differential if stoppings leak than is necessary with tight stoppings. Every mining engineer engaged in the analysis of projected mine-ventilation circuits is therefore confronted with the problem of making proper allowance for the effects of leaking stoppings. The purpose of this paper is to present evidence in support of the author's suggestion that circuit pressure increase (per cent)

Jan 1, 1942

By Walter Miller

During the second year of America's active ia in the war the inain objectives of the petroleum-refining industry were again to provide the four most important product needs for war: 100-octane aviation gasoline, toluene for T.N.T. production, high-quality lubricating oils for the needs of aviation and the armed forces, and petroleum chemicals for synthetic rubber manufacture. All other materials supplied by the petroleum industry took an inferior priority ranking, depending on the degree of essentiality. To accomplish the above objectives the industry initiated and carried on a building program during 1942 and 1943 which will put those two years down in petroleum-refining history as the greatest construction years of all time, a record which will hold for decades to come. Led by an estimated total of $ 900,000,000 going into 100-octane and contributory plant investment, it is easy to picture a total of two billion dollars and more going into additional refining-industry plant investment during 1942 and 1943, most of it privately paid for, but a substantial part covered by R.F.C. Government money financing. Some of the new plants will not be completed until 1944, but a large proportion of the program was finished and put into operation, adding substantially to the output of the four principal products during 1943- lne most important and spectacuiar activity of the refining industry is of course the 100-octane gasoline program necessitated by the fact that nearly 90 per cent of the requirements of the United Nations is being furnished by the United States. Recent P.A.W. figures mention $goo,-ooo,ooo as the cost of the construction looking to increasing the output of this all-important munition. Thirty-four major plants have been completed, 11 of them during the last quarter of the year. Thirty-eight more will be completed and put into operation during the first four or five months of 1944. Twenty-two additional plants authorized during 1943 are already well under way and scheduled for production late in 1944. Early in 1942 the aim was to treble the capacity for making 100-octane gasoline then existing; later, plans were to make it five times as great, to match the increased warplane building program; and toward the end of the year the sights had been set at a still higher but unannounced target, representing six to seven times the early 1942 figure. Comparative figures issued at the end of 1943 enable one to guess a program by the middle of 1944 of eight to nine times the former production, with an ultimate production in 1944 of eleven or more times the early 1942 output. It became obvious in 1943 that building of new units would be materially slowed because of delay in getting construction materials and that they would reach operation at considerably later dates than

Jan 1, 1944

By Raymond Mancha

When calculating the pressure-volume characteristics of projected mine-ventilating circuits by orthodox methods, certain basic assumptions are required in order to employ the various available empirical data. It is assumed, for example, that the mine air is an incompressible fluid subjected to isothermal flow, an assumption sufficiently accurate for practical purposes since pressure and temperature differentials are small throughout the average circuit. A more erroneous assumption, however, is that all air is accounted for as it travels throughout the mine. No attempt is usually made to evaluate stopping leakage as it occurs; instead, the air volume required at the last crosscuts is assumed to enter the mine, travel the various intake air courses intact, sweep the workings and travel out by the return air courses to the point or points of exit from the mine. Actually, there is a leakage of air from intake to return at every stopping, the quantity of this leakage depending upon the tightness of the stopping and the pressure difference across the stopping. Unfortunately, a lack of empirical data and knowledge of the condition of individual stoppings makes an exact analysis of underground stopping leakage impossible. Generally, leakage is most severe through the old stoppings outbye the circuit. These are also subjected to higher pressure differences than the newer inbye stoppings. Therefore the circuit air volume diminishes at a decreasing rate progressing from outbye to inbye the circuit. Consider a simple mine circuit consisting of one intake and one return air course, each of equal and uniform section area and interconnected at regular intervals with crosscuts equipped with stoppings. At any point X inbye the circuit the air volume q on the intake air course equals that on the return air course and decreases with diminishing rate from outbye to inbye the circuit between the limits of Q1 completely outbye and Q completely inbye. Such a volume change is represented by curve a, Fig. I, which is computed with the aid of the equation q = Q1- (Q1- Q)(X + L)N. This equation results from the general algebraic equation of form q = k, — kXN after solving for kl and k with the knowledge that completely outbye X = o and q = QL, also completely inbye X = L and q = Q. Curves a, b and c, Fig. I, show values of q as ordinates versus values of X as abscissas, for values of N equal to 0.50, 1.00 and 2.00, respectively. Distribution of underground stopping 1eakage directly affects the air-volume distribution along the circuit, which in turn determines the circuit pressure gradient. To deliver any required air volume inbye a circuit or portion thereof requires a higher circuit-pressure differential if stoppings leak than is necessary with tight stoppings. Every mining engineer engaged in the analysis of projected mine-ventilation circuits is therefore confronted with the problem of making proper allowance for the effects of leaking stoppings. The purpose of this paper is to present evidence in support of the author's suggestion that circuit pressure increase (per cent)

Jan 1, 1942

By Harry M. Mikami

Refractories are heat-resistant, generally nonmetallic materials used as the linings of furnaces or high temperature vessels in the steel, iron, nonferrous metals, glass, cement, lime, ceramic, chemical, petroleum, paper, and power and heat generation industries. Refractories must have structural strength at high temperatures but also, in many applications, must simultaneously resist chemical-physical corrosion-erosion from stags, metals, granular solids, or gases. Among the major uses are the pyrometallurgical processes for producing iron, steel, copper, aluminum, nickel, lead, zinc, etc. Rotary cement kilns, glass tanks, refineries, utility boilers, chemical and ceramic (including refractories) plants, and a myriad of other smaller scale users employ refractories in the high temperature parts of their operations. Thermal, chemical, and structural conditions under which refractories are used differ widely so there is a great variety of refractories to fill the various needs. Two major classifications are the "basic" and "acid" types. Basic refractories include magnesia and chromite, singly and in combinations, dolomite, and forsterite (olivine). The acid category includes aluminosilicates, alumina, and silica. There are a number of other specialized types such as carbon, graphite, silicon carbide, zircon, and zirconia that have important applications but are used in much smaller amounts than the major categories. Physically, refractories can be divided into bricks and shaped products on the one hand and unshaped or monolithic products (also termed specialties) on the other. There are many further subclassifications and divisions, a discussion of which is beyond the scope of this chapter; see Refs. 2 and 9. Raw materials for the principal basic refractories are magnesia and chrome ore. Magnesia, generally termed magnesite or periclase, is obtained mainly from seawater or saline brines extraction, but substantial amounts are produced from mined magnesite (MgCO3). Dolomite (CaCO3•MgCO3), another important basic refractory, is obtained entirely from mined sources. Acid refractory raw materials are: fire clays, flint clays, kaolin, and other natural clay minerals; aluminosilicate minerals such as kyanite, andalusite, sillimanite, pyrophyllite, bauxitic clays; calcined refractory grade bauxite, alumina from the Bayer process for the alumina group; and quartzitic rocks for silica refractories. The total value of all refractories shipped in the United States in 1974 was $989 million, a record to that date. Of this amount, about 73% represents bricks and shaped products and 27% is in nonshaped or monolithic products which comprise mortars, cements, castables, plastics, and ramming and gunning mixes. Fig. 15.4E.1 shows the rising value of all U.S. refractory shipments in the period 1948-1974. Values of brick and shapes paralleled

Jan 1, 1976

By Walter Miller

During the second year of America's active ia in the war the inain objectives of the petroleum-refining industry were again to provide the four most important product needs for war: 100-octane aviation gasoline, toluene for T.N.T. production, high-quality lubricating oils for the needs of aviation and the armed forces, and petroleum chemicals for synthetic rubber manufacture. All other materials supplied by the petroleum industry took an inferior priority ranking, depending on the degree of essentiality. To accomplish the above objectives the industry initiated and carried on a building program during 1942 and 1943 which will put those two years down in petroleum-refining history as the greatest construction years of all time, a record which will hold for decades to come. Led by an estimated total of $ 900,000,000 going into 100-octane and contributory plant investment, it is easy to picture a total of two billion dollars and more going into additional refining-industry plant investment during 1942 and 1943, most of it privately paid for, but a substantial part covered by R.F.C. Government money financing. Some of the new plants will not be completed until 1944, but a large proportion of the program was finished and put into operation, adding substantially to the output of the four principal products during 1943- lne most important and spectacuiar activity of the refining industry is of course the 100-octane gasoline program necessitated by the fact that nearly 90 per cent of the requirements of the United Nations is being furnished by the United States. Recent P.A.W. figures mention $goo,-ooo,ooo as the cost of the construction looking to increasing the output of this all-important munition. Thirty-four major plants have been completed, 11 of them during the last quarter of the year. Thirty-eight more will be completed and put into operation during the first four or five months of 1944. Twenty-two additional plants authorized during 1943 are already well under way and scheduled for production late in 1944. Early in 1942 the aim was to treble the capacity for making 100-octane gasoline then existing; later, plans were to make it five times as great, to match the increased warplane building program; and toward the end of the year the sights had been set at a still higher but unannounced target, representing six to seven times the early 1942 figure. Comparative figures issued at the end of 1943 enable one to guess a program by the middle of 1944 of eight to nine times the former production, with an ultimate production in 1944 of eleven or more times the early 1942 output. It became obvious in 1943 that building of new units would be materially slowed because of delay in getting construction materials and that they would reach operation at considerably later dates than

Jan 1, 1944

By C. C. Nathan

Data are resented on the physical properties of five waxes obtained from fields in Texas and Louisiana in which "parafin" troubles are being experienced. The crude parafin was fractionated into three components, voluble in cold acetone, soluble in boiling acetone, and insoluble in boiling acetone. The acetone insoluble fraction was found to consist essentially of straight chain parafin hydrocarbons in the molecular weight range 525 to 700. Solubilities of the purified high molecular weight parafins were determined in a number of solvents. It was found that in hydrocarbon solvents, including crude oil, solubilities could be calculated satisfactorily by use of ideal solubility relations. In chlorinated, and oxygenated solvents, large deviations from ideal behavior were observed. These deviations could be partially correlated with the internal pressure of the solvent. INTRODUCTION A problem encountered in many producing oil fields is that of "paraffin" deposition. The problem refers to the deposition of material from the crude oil onto tubing, pumping rods, flow lines, or other material contacted by the crude. This problem has been recognized for nearly a hundred years, and numerous investigations have been reported on its causes and prevention or alleviation. One of the more comprehensive of such investigations was published by Reistle1 in 1932. A few of the salient findings of his report are briefly as follows: The term "paraffin" as used to describe this problem refers to the deposit of carbonaceous material which is not soluble or dispersible by the crude oil under the conditions where deposition occurs. The "paraffin" normally consists of high molecular weight paraffin hydrocarbons, both straight chain and branched, resins and asphaltic materials of undetermined nature, occluded oil and water, and possibly sand. In consistency, the deposit may vary from a soft, sticky material, to one which is hard and brittle. Deposits are usually black, although lighter colors are sometimes observed. Under the conditions of temperature, pressure, and crude oil composition occurring in the underground reservoir, the paraffin is in suspension or solution in the crude. As the oil flows to the surface, there is generally a reduction of temperature, pressure, and the amount of dissolved gases contained in the oil. Reduction of temperature and gas break-out were shown by Reistle to be factors causing reduced solubility of the paraffin in the crude. Thus, as the crude containing paraffin rises to the surface and flows to storage tanks at atmospheric temperature, the solubility of the paraffin may be exceeded. Deposition will begin at the point in the system where the temperature of the system falls below its cloud point, and continue as long as there is a further drop in the solution power of the crude for the paraffin. The severity of the deposition as well as the location of the bulk of the deposition, i.e., in subsurface or surface equipment, will depend on the amount of paraffin originally in the crude, the manner in which pressure and temperature of the crude

Jan 1, 1956

By L. D. Wooddy, W D. Moore

Water drives may be natural or artificial. For the case of a natural water-drive reservoir, the volume of water influx corresponding to reservoir pressuve-production history may be calculated by means of the material bal-ance-unsteady state equation. For the artificial water drive or pattern injection water flood, the material balance equation is sufficient to determine the reservoir pressure-production, injection history. However, for both cases to reliably predict reservoir performance, it is necessary to calculate the saturation distribution of the reservoir fluids at different stages of depletion. This paper consolidates the various equations used to determine the performance of water-drive reservoirs into one approach that is applicable to any reservoir that has a natural water drive or is to be produced by water injection. The numerical procedure has been simplified considerably, and the solution is adaptable to either hand calculations or digital computer operation. INTRODUCTION A water-drive reservoir is one in which the predominant source of energy for production of oil results from the encroachment of water into the oil zone. The water drive may be either natural or artificial. Water invasion takes place by expansion of water in the aquifer as a result of the pressure decline transmitted from the oil reservoir. Because water is practically incompressible, a natural water drive requires an extensive aquifer containing a volume of water many times the volume of oil in the reservoir. Provided the permeability of the formation is reasonably high, a moderate decline of reservoir pressure usually causes adequate water influx. If the reservoir pressure decline becomes excessive because of low permeability or a high rate of production, part of the oil production may result from the liberation of dissolved gas which may cause excessive quantities of free gas to be produced along with the oil. In extreme cases, reservoir pressure may decline so rapidly as to cause the oil to be produced predominantly by dissolved gas drive, leading to abandonment of the reservoir before the advancing water has had a chance to flush the entire reservoir. In reservoirs that are not connected to extensive aquifers, an artificial water drive may be created by injecting water into or around the lower edges of a reservoir. Sometimes water is injected within the reservoir through wells interspersed among the producing wells. When injection is carried out in such fashion, the reservoir is in effect subdivided into a number of separate producing segments, in each of which the displacement of oil is simultaneously taking place, and the shapes of which are fixed by the well patterns employed. Because of the natural tendency of oil and water to segregate according to their relative densities, water will tend to migrate downdip regardless of where injected. Accordingly, the injected fluids can be retained within the intended reservoir segments only when conditions are unfavorable to their migration under the force of gravity. Pattern injections are usually confined, therefore, to reservoirs having low structural relief, or low permeability, or when production and injection rates are such that fluid movements in the reservoir are dominated by the pressure gradients rather than by the force of gravity. In the case of natural water-drive reservoirs and artificial water-drive reservoirs in which the water is in-

Jan 1, 1958

By F. G. Tahmoush, N. J. Grant, E. P. Abrahamson

The effect of grain size on the brittle -ductile transition temperature of pure iron and three dilute Fe-W alloys has been investigated by slow bend tests. The brittle-ductile transition temperature for pure iron increased with increasing grain sizes from 8000 to 500 grains per sq mm where the transition temperature then decreased with further increase in grain size. The dilute additions of tungsten lowered the transition temperature for fine grain sizes, suppressed a reversal of the curve in the coarse grained portion, and raised the transition temperature for this region. The frequency of twin occurrence increased with increasing grain size and decreasing temperature. The object of the present investigation was to re-examine the effect of grain size on the brittle -ductile transition of pure iron and several dilute Fe-W alloys. Current literature normally presents a simple relationship between grain size and the brittle-ductile transition temperature, namely, that the transition temperature increases with increasing grain size. Heslop and etch' have studied the transition temperature of mild steel by V-notch Charpy impact tests for the grain size range between 200 and 6000 grains per sq mm. The result was a linear plot of In 1-1/2 vs brittle-ductile transition temperature, where 1 is the grain diameter. Recent experiments by sipos2 revealed the possibility of a reversal in the slope of the grain size vs transition temperature plot for pure iron; however, his investigation was limited in scope, and the data obtained were insufficient to permit a definitive curve. The present investigation was undertaken in an effort to confirm or extend the grain size effect observed in iron by Sipos. PROCEDURE All alloys were vacuum induction melted, using 99.95 pct Fe containing 0.03 pct 0 and 0.004 pct C. Four ingots were made, ranging from pure iron to iron with 0.035 pct W. The chemical composition of each alloy, after processing, is given in Table I. The four alloys were prepared as 45 lb heats and cast into 4 in. diam by 16 in. molds. They were then extruded into 3/4 in. rods at 1800oF. Specimens for chemical analysis, taken from various positions along the rods, revealed no variation in tungsten content along the length. The extruded rods were reduced to 0.156 in. diam stock by a series of cold swaging operations involving intermediate vacuum annealing treatments. This procedure yielded a final cold reduction in area ranging from 10 to 90 pct. The swaged rods were chemically cleaned, cold pressed to a cross section of 0.10 by 0.18 by 1.0 in. long (2.54 by 4.73 by 25 mm). The specimens were wrapped in iron foil and vacuum sealed (10-4 mm Hg) in quartz. Various heat treatments at temperatures from 700" to 1300oC were utilized to produce grain sizes from 8000 to 1 grain per sq mm. Grain sizes were determined by measuring the average area of grains in a polished section. In specimens with grain size greater than 20 grains per sq mm, the total number of grains in the cross section was counted and then divided by the area to yield grains per sq mm. Grain size was measured both for longitudinal and transverse cross sections. The average of the two measurements was plotted vs transition temperature. An Instron Table Model testing machine was used to determine the transition temperature of specimens tested in three point horizontal bending. The specimen was supported by two 1/4 in. dowels one in. apart. Bending was accomplished with a push rod, the end of which had an 1/8 in. radius. The head speed was 50 in. per min. Temperatures were established through the use

Jan 1, 1963

By L. H. Robinson

Triaxial compression tests on Indiana limestone indicate that chemical additives in the pore fluids can increase or decrease the strength in plastic failure but not in brittle failure. Tests using a series of the sodium salts of dicarboxylic acids show that odd-number carbon-atom chains decrease the yield strength as much as 3.0 x 10 3 psi, and even-number carbon-atom chains increase the yield strength as much as 9.0 x 102 psi. ,The most effective chemical (sodium citrate) decreased the yield strength of Indiana limestone from 16.0 x 103 to 12.0 x 103 psi. The chemical additives investigated have no influence on microbit drilling rate when drilling with zero differential pressure. However, when drilling at a 2.0 x 103-psi pressure differeniial and using an odd-number carbon chain compound as the circulating fluid, the roller bit drilling rates were slower than with water whereas the drag bit drilling rates were faster. One even-number carbon chain compound added to the circulating fluid produces the opposite effect: the roller bit drilling rate is slightly faster than with water and the drag bit slower than with water. INTRODUCTION A Russian book by Rehbinderl published in 1944 generated much interest in the possibility of aiding and accelerating the destruction of solids by the action of a liquid in which the solids are deformed. This book describes a process in which microcracks are generated during elastic deformation. To describe this process, the rock is divided into three zones: (1) the zone in which the destruction takes place, (2) the predestruc-tion zone (an affected area immediately below the destroyed zone) and (3) the undisturbed specimen. Consider a load applied normally to a surface of an infinite slab of rock. Immediately below the point of application of the load, the rock is destroyed by compression or shear forces. Below this area of destruction, because of a great number of discontinuities ranging from defects to weak points in crystals of discontinuities in crystal latices, very small cracks are created in or between the crystals (often referred to as microcracks). Upon removing the load, the broken rock in the destroyed zone could be removed. In the lower predestruction zone, however, the microcracks in and between the crystals could disappear by the process of rehealing, i.e., the molecular attraction from one side of the crack to the other side being sufficient to completely eliminate the crack. Thus, a large number of these microcracks possibly exist only for a relatively short period of time. The concept of small cracks being generated within the crystals of a rock is not unreasonable. If the rock matrix is deformed below the yield point, some of the defects present within the crystalline structure could start small cracks through the interior of the grains. Upon removal of the load, these microcracks reheal (or the newly generated surfaces come back together) so that all evidence of cracks completely disappears. Under various types of loading, and in various types of fluids, the rehealing of these cracks would be time dependent. If a liquid adhered to the surface of a rock, it could penetrate into the microcracks and thus delay or prevent the rehealing process. This suggests that the prevention of healing of the microcracks may be dependent upon the wetting characteristics of the solid. Thus, rocks which are water-wet should be more easily destroyed in water than in nonpolar hydrocarbon liquid. Adsorption of a liquid could also reduce the free surface energy which could explain the decrease in strengths of materials under nonrepetitive-type loading. Rehbinder's work prompted Boozer, Hiller and Serdengecti 2 to examine the effects of pore fluids on the deformation of rocks subjected to triaxial compression over a range of confining pressures, temperatures and strain rates. Fluids which strongly adsorbed on the rock grain surfaces decreased the strength of sandstone and limestone, which deformed plastically. For certain strain

By A. Romero-Juarez

This paper is concerned with the effect of propping-agent concentration on flow capacity of a fracture in the case in which there is embedment of the propping agent. Previous published studies have shown definitely that there is a relationship between fracture flow capacity and prop ping-agent concentration, and it has been shown that the theoretical results are confirmed by laboratory experiments. The problem of directly finding sand concentration for maximum flow capacity of a sand-propped fracture is solved, and formulas and charts are given to obtain this concentration under various conditions of effective overburden pressure, medium sand-grain diameter and rock properties. It is shown that, for the same effective overburden pressure and the same rock characteristics, optimum sand concentration in pounds per gallon does not depend on medium sand diameter. For conditions met in bydraulic fracturing operations, it is found that sand concentration in grains per square inch for maximum flow capacity varies within a wide range of values; this indicates the convenience of using data of fracturing pressure and rock characteristics for calculating sand concentration in order to achieve the best results in fracture treatments. INTRODUCTION It has been pointed out in the published literature1 that one important factor controls the success of a hydraulic fracturing operation — the propping of the fracture. The main effect of the propping agent is to hold the fracture open by means of the reaction forces that oppose the pressure due to the overburden. It is assumed in this paper that the propping agent is sand, that the grains are spherical and uniform in size, and that this sand is distributed in a monolayer in the fracture. The existence of a sand concentration value for maximum fracture flow capacity has been recognized since the publication of one of the first studies on the subject.2 In the reference cited, flow capacity was assumed to be proportional to the cube of the fracture volume per square inch not filled by sand. The obtained experimental curves relating to flow capacity and sand concentration had the same appearance as the curves obtained with the afore-mentioned assumption. Recent work3 has shown that fracture permeability, in the case of a monolayer, can be calculated accurately by means of a modified Kozeny-Cacman equation; thus, it can be shown that fracture pqmeability is a function of free volume in the fracture and of the rock and sand wet surfaces. The flow capacity of a fracture is dependent on the permeability of the fracture and on the fracture width. If all excessive quantity of sand is present in the fracture, its width may be large but its permeability i:; low due to the greater flow resistance; too few grains of sand per square inch are present in the fracture, sand embedment in the rock is greater and the width becomes small enough to appreciably decrease the rate of flow. To determine optimum conditions of flow, therefore, it is necessary to know the dependence of fracture width on density or concentration of propping agent. This relation is given in a study4 in which the approach to embedment is similar to the one made in a penetration hardness test of metal. With the equacions presented by Darin and Huitt,3 the number of sand grains per square inch that results in maxirnum fracture capacity can be determined graphically by plotting fracture capacity vs sand concentration. Since the relationship between fracture capacity and sand concentration may be considered known, one is led to formulate the analytical problem of directly determining sand concentration for maximum fracture flow capacity, in order to study the effect of the various quantities that come into the process. The solution of this problem appears to be interesting both from the viewpoint of fluid mechanics and from the practical viewpoint of oil production in hydraulic fracturing treatments. EQUATION FOR FRACTURE FLOW CAPACITY It can be shown3 that the fracture flow capacity of a monolayer is given by the following expression,

By B. M. Larsen, T. E. Brower

INTRODUCTION AND SUMMARY BY "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath, To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over 1 million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct, The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 lb oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 lb oxygen replacing 145 lb ore per ton of steel) decreased the

Jan 1, 1948