Search Documents

By William H. Spice

Exploratory drilling in South Central Texas for the year 1944 showed a marked increase over that of 1943 and resulted in a similar increase in new fields discovered. In this area, which comprises the 30 counties included in district No. I, Oil and Gas Division, Railroad Commission of Texas,? 61 exploratory wells were drilled during 1944 as compared with 29 exploratory wells drilled during 1943, or an increase of over 100 per cent. Three new oil fields, two new gas fields and one gas-distillate field were discovered during the year, as compared with one new oil field and one new gas field discovered during 1943. These new fields were the result of exploratory drilling throughout the district along the Wilcox trend and the deeper Edwards lime trend, which was started during the previous year. The Wilcox trend yielded the new Loma iilta-Wilcox oil field and the San Caja gas-* tlistillate field, both in McMullen County. The Charlotte field, in Atascosa County, was discovered along the deeper Edwards lime trend. These three discoveries were of considerable importance and subsequent development should indicate the desirability of continued exploration along these trends. The other three discoveries, United oil field in Guadalupe County, Pederson gas field in Milam County and Van Cleve gas field in Zavalla County, were of minor importance. Charlotte Field, Atascosa County, was discovered by the Humble Oil and Refining Company's No. 3 Pruitt, completcd on Aug. 9, 1944, flowing 176 bbl. per day, 3/16-in. choke, 710 lb. tubing, 475 lb. casing pressures, 37.7º A.P.I. gravity, from the top of the Edwards lime from 6917 to 6923 ft. Two oil wells were completed during the year in this field. This discovery is 14 miles southwest of the same company's Imogene field, also producing from the Edwards lime but with considerable difference in reservoir characteristics. The discovery of this field is the result of surface geology and subsequent seismograph survey of the area. Loma Alta-Wilcox Field, McMullen County, was discovered by the Atlantic Refining Company's No. I Atkinson, completed on June I, 1944, flowing 102 bbl. per day, 9/64-in. choke, 1900 lb. tubing pressure, 37º A.P.I. gravity, from Wilcox sand from 6866 to 6869 ft. after being drilled to a total depth of 7185 ft. This discovery is the result of subsurface geology and an extensive seismograph survey of the entire area. Sun Caja Field, McMullen County, was discovered by Edwin M. Jones No. 2-C Ezzell, completed on June 2, 1944 as a dual completion in the Wilcox sands, flowing 1,740,000 cu. ft. gas with 53 bbl. distillate, 1/4-in. choke, 2035 lb. tubing pressure, 53.2º A.P.I. gravity, from sand 6416 to 6453 ft. and flowing 2,000,000 cu. ft. of gas with 127 bbl. distillate, 1/4-in. choke, 2500 lb. tubing pressure, 50º A.P.I. gravity, from sand 6889 to 6916 ft., after being drilled to a total depth of 7264 ft. Three gas-distillate wells were completed during

Jan 1, 1945

By Wm. R. Webster

THIS is a contribution for the proposed new discussion on the physics of steel. The former discussion on the subject started with the consideration of five papers presented at the Chicago meeting in 1893, and continued for several years. The Suggested Lines of Discussion, prepared by Doctor Howe, covered a wide field and added greatly to the success of the work. Naturally, the first step in a new discussion will be to remodel and bring up to date the old Suggested Lines of Discussion so as to embody all the important advances in the metallurgy of steel that have a bearing on the physics of steel and keep the papers and discussions within the field of work undertaken. This paper will be devoted to the practical application, in rolling steel, of the effects of carbon, phosphorus, and manganese on its tensile strength, with some suggestions on further research work. Dr. J. E. Stead, in his paper Influence of Some Elements on the Mechanical Properties of Steel,1 gave a complete review of all that had been done during the past thirty years. He gave full credit to all investigators who worked on these lines, also their results, with his views on same, and in many cases his own results. All of this data and much new valuable information were put in convenient shape for reference and study. To do this required a great deal of work, which is fully appreciated by the steel manufacturers and investigators. The variations in the values given by the different investigators for the increase of the tensile strength of steel for each 0.01 per cent. of carbon, phosphorus, and manganese were largely due to the steels they worked on, the large or small variations in the amount of the elements present, and the omission to take into consideration all the factors, from the blast furnace through to finished rolled material, that affect the character of the steel. For instance, a poorly made dirty steel requires considerably more carbon to give the same ultimate strength than a well-made clean steel with the same phosphorus and manganese content.

Jan 3, 1921

By S. Mukai, Y. Shah, T. Zshikawa, T. Wakamtsu

In order to recover coal concentrate of low ash and low iron content, the electrostatic separation of coal was studied. It is more successful in the corona discharge field to recover the coal concentrate of low ash and low iron content than in the field without corona discharge. The effect of humidity on the electrostatic separation of coal was then studied. From the experimental results, it was clear that the electrostatic separation was excellent in about 60% relative humidity of atmosphere. Thus, the separation of vitrite from coal is practicable by electrostatic separation. In recent years the demand for high quality coal containing low ash, low iron, and low sulfur has increased. To fulfill this requirement, a higher grade coal concentrate must be produced. Study on the electrostatic separation of coal has been performed for several years in the author's laboratory. From the results of this research, it was considered that the behavior of coal particles in the electrostatic field relates closely to the ash and iron content in coal. In the present paper, the electrostatic separation of coal in corona discharge field was studied in order to recover the high quality coal concentrate and then the effect of humidity on the electrostatic separation was investigated. PREPARATION OF COAL SAMPLES The coals from the Akabira mine, the Kushiro mine, the Miike mine, and the Oshima mine which are famous coal mines in Japan were used in this study. The ash contents of these coals are shown in Table I. From the results of the analysis of the coal samples by the Norelco X-ray diffractometer, it is recognized that the Miike coal includes mainly pyrite, quartz, kaoline, calcite, and epidote; the Kushiro coal: kaoline, quartz, and montmorillonite, and the Oshima coal: siderite, dolomite, and other substances. For the preparation of samples, the coarse pieces of coal were crushed to about 2 mm in diam and then ground in an agator mortar. The ground products were sieved and fractions of 10 — 14 mesh, 14 — 20 mesh, 20-28 mesh, and 28-35 mesh were prepared, respectively. APPARATUS OF ELECTROSTATIC SEPARATION The principal part of the apparatus of the electrostatic separation used in the experiments is shown in Fig. 1. In order to generate the corona discharge field, a needle-shaped electrode combined with a pole electrode is installed as the high tension electrode. In the case of investigating the effects of the humidity on the electrostatic separation of coal, the needle-shaped electrode was combined with a plate electrode instead of the pole electrode as shown in Fig. 2. The pole or the plate electrode was installed to promote the repelling of the charged particles by producing the electrostatic field between this electrode and the grounded roller. It seems to be very useful on the coal separation to install these combined high tension electrodes. SEPARATION OF COAL PARTICLES IN CORONA DISCHARGE FIELD The separation testings on the coal samples in the corona discharge field were performed by the apparatus as shown in Fig. 1. These experiments were carried out under the following conditions: feed size 20 — 28 mesh, room temperature, normal humidity and applied voltage 15-20 KV, and the combined electrodes including the needle-shaped electrode were negatively charged. The results of these testings are

Jan 1, 1968

By L. Guttman

THE equilibrium diagram of the indium-thallium system was of interest to us in connection with a study of the superconducting properties of metallic solid solutions in progress at this Institute. For this purpose, a series of alloys was prepared covering the range from pure indium to 75 atomic pet TI, and X-ray diffraction patterns were obtained. Roughly speaking, the results indicated a region of continuous decrease in the axial ratio of the face-centered tetragonal structure from the value ca. 1.08 in pure indium to unity at about 23 atomic pct TI. From this concentration to the solubility limit, the structure was face-centered cubic, a form not reported by Hansen.1 At this point we became aware of the work of Valentiner,2 who had found the same structures at room temperature but had not investigated further the relationship between them. To study the transformation f.c.c.??f.c.t., and to clarify the phase diagram, we undertook the work reported in this paper and that which follows." Preparation of Alloys Pure indium and thallium* (both about 99.9 pct, as estimated from spectroscopic analyses) were weighed out in quantities sufficient to prepare 10 to 25 g of alloy of the desired concentration. (Occasionally indium was mixed with a previously pre- pared solution.) The metals were melted over a flame, in an open graphite crucible, stirred with a graphite rod, and poured into a graphite trough. The rough slug was hammered and swaged into a rod of 2 to 3 mm diam, and annealed in a drying oven at about 125°C for 1 to 2 days. Samples were taken from the rod for analysis, as well as for diffraction and other measurements. The thallium was determined by electrometric titration, using a modification of the method of Beale and co-workers.' The precision of analysis was generally about 2 0.2 pct of the thallium content. The rods were sometimes found to vary in thallium content as much as 1.5 pct from end to end, but since analyses were also made close to the segments used in the various studies, the composition was usually known as accurately as the analyses could be made. Where one less significant figure is given, the error is estimated to be ±0.4 pct of the thallium content. X-Ray Diffraction Measurements Three different cameras were used: (1) A 7 cm Debye camera, with oscillating specimen (manufactured by the Picker X-ray Corp., Cleveland, Ohio); (2) a 9 cm diam Debye camera of the type designed by Bradley;" (3) a 10 cm diam symmetrical focusing back-reflection camera (manufactured by Geo. C. Wyland, Ramsay, N. J.). Samples were prepared from the homogenized rods, either by filing under liquid nitrogen, or more often, in the form of wires or foils made by working at room temperature or liquid nitrogen temperature. Sharp patterns were obtained from specimens annealed at room temperature, although higher annealing temperatures were also used (cf. below). Generally, copper radiation was used; a few patterns were obtained with

Jan 1, 1951

By F. E. Jaumot, A. Sawatzky

IT as long been recognized that there is a need for accurate systematic data on diffusion in solids. Originally, such data were needed to check existing theories but, more recently, it would appear that it could be used most advantageously as a guide to, or a check for, much needed extensions of the theory of diffusion. The awareness of the conditions which are important to experimental accuracy, the availability of the materials for accurate experiments, and the techniques have improved to the extent that it would now seem to an experimentalist that, unless extensions of the theory are made which take into account the fundamental parameters of the atoms, the electrons, and the lattice in some detail, the field of diffusion will rapidly become an empirical or semi-empirical field. The present series of experiments was designed to provide accurate data on the diffusion of the elements of the IB and IIB subgroups in silver; that is, to provide data on the diffusion in silver of three face-centered-cubic elements with roughly similar chemical properties, but with different atomic or ionic sizes and, similarly, for three noncubic elements. The elements of these two subgroups have different valences, so that the data will not give any significant information on differences due to the crystal structure of the solute. The present paper reports data on the diffusion of copper and mercury in single crystals of silver; the data for the other elements of the IB and IIB subgroups were reported previously by the authors1'2 and by Tomizuka and Slifkin.8 Experiment The general technique used was identical to that previously described1,2 and will not be repeated here. In all cases, the sectioning technique and high specific activity isotopes" were used. The short half-life of Cu64 made decay corrections more important than for the other isotopes, and necessitated around the clock shifts while data were being taken. Each section was counted at least twice (as was true for all longer half-life isotopes) and a monitor was counted along with each sample. Data for the diffusion of mercury in silver are presented at a greater number of temperatures than for the other solutes. This is a result of two circumstances. First, six (of 30) samples had to be discarded because of pitting or recrystallization which occurred during the diffusion runs, even though the samples had sustained high temperature prediffusion anneals. Either of these was a very rare phenomenon in the other experiments, and their occurrence in this case is considered in more detail below. Second, the curves of the logarithm of the activity of the sections vs the square of the penetration deptht were, in general, quite good, but frequently seemed to show one point to have high activity and the next point to have slightly low activity in terms of the best straight line. When this occurred, there was remarkable regularity of the high-low sequence. In any event, the results, as far as diffusion coefficients are concerned, were not affected by this amalgam effect. In fact, the mercury data had the highest internal consistency of any of the data. Results Diffusion of Copper in Silver—-Diffusion runs were made at eight temperatures In the temperature range from 700° to 950°C, for times ranging from 5 to 45 hr. A linear curve of the logarithm or the activity vs the square of the penetration depth was obtained for all samples. Table I summarizes the results for individual samples and Fig. 1 gives a plot 02 the logarithm of the diffusion coefficients as

Jan 1, 1958

By F. O. Jones

The capabilities of small proportions of divalent cations, such as calcium or magnesium, for controlling clay blocking are reported. Potentially sensitive formations can be exposed to fresh water if at least one-tenth of the salts dissolved in both the native water and invading fresh water are calcium and magnesium salts. Often, even less suffices. The behavior evidently depends upon the cation exchange properties of the clays, which favor adsorption of calcium and magnesium over sodium. Clays having sufficient adsorbed calcium and magnesium resist dispersion by water and consequent blocking of permeability. An allied phenomenon, the dependency of clay blocking on salinity contrast, is also reported. Abrupt change from highly saline to fresh water can cause blocking which may not occur if salinity is lowered slowly. A process related to osmosis is thought responsible for this behavior. Applications of findings to drilling, fracturing and water flooding are discussed. INTRODUCTION Many formations, when exposed to fresh water, can lose permeability through clay effects.',' For example, drilling-mud filtrate can cause oil permeability decreases, which persist long enough to interfere with drill-stem testing and well completion.3 Ultimate productivity may suffer when clay damage is severe, especially if drawdown pressures are low.' The injection pressures and the time required for water flooding can increase if clay blocking occurs. Earlier work indicates that clay blocking is caused by obstruction of flow channels by clays or other mineral fines dispersed by fresh water.'!" It is well known that increasing salt concentrations in water tends to prevent clay blocking. Also it is well established, although perhaps not as widely known, that the nature of the dissolved solids is also important. If, for instance, formation clays are exposed to calcium chloride solution and then exposed to weaker solutions of calcium chloride or distilled water, considerably less permeability damage results than if the clays had been exposed instead to sodium chloride solutions. The reasons for this behavior are: (1) clays are cation-exchange, or base-exchange, materials similar in this respect to zeolites or exchange resins, and (2) clays in the calcium form do not disperse easily in fresh water, whereas clays in the sodium form do. The base-exchange form of a clay is easily altered by flowing a solution through it. For example, a sodium clay can be changed to a calcium clay simply by passing a calcium chloride solution through the clay bed. There is general agreement that the reason calcium and magnesium clays do not disperse easily in fresh water is because the calcium ions do not ionize easily from the clay surfaces.' Sodium clays, however, are believed to allow the sodium ions to ionize from the clay particle surfaces. In fresh water, this allows the particle to accumulate a net negative electrical charge great enough for the particles to repel one another and, therefore, disperse more easily. The foregoing suggests that, even in the presence of a large excess of sodium, a relatively small ratio of divalent cation, such as calcium or magnesium, might serve to prevent clay dispersion. The divalent ion probably adsorbs to a disproportionately large extent, because of being adsorbed more tightly, with the result that the proportion of divalent cation on the exchange positions of the clay might then be great enough for the clays to resist dispersion. Consequently, an investigation was conducted to find how mixtures of salts in solution influence clay blocking. APPARATUS AND PROCEDURE Water permeability tests were conducted using conventional techniques. The equipment is illustrated schematically in Fig. 1. Flow rates of solutions driven through small core samples at known temperatures and pressures were measured. Regulated compressed air, usually at 10 to 15 psig, was used to drive the solutions. Core samples 0.75 in. in diameter and 1 in. long were used for the most part. Cores were saturated by evacuating and then admitting a de-aerated solution. Tight core samples were first saturated with carbon dioxide gas and then evacuated and saturated with the test solution. After saturation, 140 psig pressure was imposed for several hours. Cores were tested to insure absence of gas saturation by a Boyle's

Jan 1, 1965

By R. J. Quigg, G. S. Doble

Commercial stress -relieved TD Nickel bar was shown to retain room- and elevated-temperature tensile strength after exposure up to 2501°F. Cold swaging increased both room -temperature and 2000°F tensile strength. After annealing at 2500°F the strengthening due to swaging was retained at 2000°F hilt eliminated at room temperature. Annealing produced changes in hardness and X-ray half peak width indicating the presence of recovery processes as 1071° as 1000°F but no recrystallization of swaged material was noted at any temperature. In contrast to swaging, rolling induced a recrystal-lized structure after annealing. The tensile strength of this recrystallized structure was comparable to the cold-worked condition. High-temperature tensile properties of as -received bar were highly anisotropic with the transverse tensile strength being one fifth the longitudinal value. The aniso-/ropy is affected by working direction and may he partially reversed by changing the direction of metal flow. The divergence in tensile strength, beginning above 550°F or- approximate one third the absolute melting point, is strain-rate dependent. T D Nickel is a commercial dispersion-hardened alloy containing 2 vol pct thoria. The dispersion, consisting of spherical particles 0.030 to 0.050 in diameter with an interparticle spacing of less than 1 is reported to maintain stable properties up to 2400°F.1 This stability of second phase results in maintenance of elevated-temperature strength at higher temperatures and longer times than normal nickel-base superalloys.2 The purpose of this paper is to describe the effect of various mechanical working operations on the strength and microstructural stability of TD Nickel bar. MATERIAL AND PROCEDURES All material used in this study was commercial TD Nickel bar. This material is produced by a chemical process which results in a nickel powder containing a dispersion of thoria particles. The powder is then pressed, sintered, extruded, and subsequently worked to bar stock. Three starting materials from three separate lots were used: as-extruded bar. 1-in.-diam stress-relieved bar, and 1/2-in.-diam stress-relieved bar. Since TD Nickel bar stock is cold-worked without a recrystalliza-tion anneal, the accumulated deformation or degree of cold work in these materials increases as the bar diameter decreases. Some of the 1/2-in.-diam bar was swaged to 1/4 in. diameter at room temperature in order to produce an as-worked condition for comparison with the stress-relieved stock. Tensile testing was performed on an Instron Tensile Tester at a constant crosshead speed of 0.020 in. per min. The 0.2 pct offset yield strength was measured from the load-crosshead movement plot. Specimen gage dimensions were 0.080 in. in diameter by 0.40 in. in length, producing a strain rate of approximately 0.050 min-1. Specimens were tested in air and heated within a resistance-wound furnace controlled to ±5°F. A 15-min soak at temperature was employed before testing. Samples were heat-treated in air and specimens machined after exposure with sufficient material removed to eliminate any surface contamination. X-ray line breadth was determined from a diffractometer scan of a transverse face of a bar using copper K, radiation. Metallographic preparation utilized standard mechanical polishing with Carapella's etch. Specimens for electron microscopy were electropolished in a 1:7 sulfuric/methaol solution and chromium-shadowed collodion replicas prepared. RESULTS AND DISCUSSION I) Effect of Elevated-Temperature Exposure on the properties of TD Nickel. The effect of various elevated-temperature exposures on the room-temperature tensile strength of TD Nickel is shown in Table I. In the unexposed condition the tensile strength, reduction in area, and hardness all increase with increasing accumulated deformation while the elongation decreases. After exposure at 2500°F the strength of all three materials decreases to about 65,000 psi and the elongations increase slightly. The apparent increase in strength of the 1-in. bar after a 2000°F treatment is probably experimental scatter. These results indicate that the room-temperature strengthening due to additional deformation is annealed out upon elevated-temperature exposure. In contrast to the room-temperature data, the 2000°F tensile strengths increase in order of increasing deformation even after exposure. Although some loss of strength occurs after exposure, much of the effect of working is still maintained at 2000°F. The room-temperature hardness after various

Jan 1, 1965

By George V. Smith, Daniel E. Sonon

Various mechanical properties of the Ni-Co-C alloy system were investigated to delineate the strengthening effect of carbon. Carbon concentration, cobalt concentration, vain size, temperature, and strain rate were varied so that thermal activation analysis and the Hall-Petch analysis could be used to evaluate the strengthening effect of carbon. Increasing carbon increased the strength of nickel and a Ni-60 pct Co alloy , with the effect becoming more pronounced at lower temperatures. Yield stress depended linearly on carbon concentration in nickel, but it depended on the square root of carbon concentration in the Ni-60 pct Co alloy. The Hall-Petch slope of nickel increased with carbon concentration; however, that of the Ni-60 pct Co alloy did not. The yielding behavior of these alloys was sensitive to composition, grain size, and temperature. Cobalt eliminated serrations in the flow curve of carbon-containing nickel at 300' and weakened them severely at higher temperatures. Pairs, or clusters, of carbon atoms appear to be responsible for the observed strengthening behavior. FLINN' conducted several experiments with carbon in nickel in an effort to provide information on the strengthening effect of interstitial impurities in solid solution in fcc metals and alloys. Strengthening which increased with decreasing temperature led him to conclude that carbon causes Cottrell locking in nickel. Fleischer2 analyzed Flinn's data and calculated that the strengthening effect of carbon in nickel was smaller by a factor of fifty than the strengthening effect of carbon in a! iron. Fleischer2 termed the magnitude of strengthening of carbon in nickel "gradual" and that of carbon in a! iron "rapid". He attributed "gradual" hardening to hydrostatic strains and localized changes in modulus of elasticity around solute atoms, whereas he attributed "rapid" hardening to tetragonal strains around solute atoms. Sukhovarov et a1.3-7 reported strain aging and serrated plastic flow in nickel, both of which they attributed to the presence of carbon. Serrated plastic flow has been rationalized by a process involving a series of dislocation pinning and multiplication steps.8, This process is more probable when screw dislocations are strongly pinned. Screw dislocations cannot be pinned by pure hydrostatic forces from the symmetrical strains of an interstitial impurity in an fcc lattice, except for small, second-order effects. However, they might be pinned by localized changes in modulus of elasticity around solute atoms,' by the pinning of the edge components of the partial dislocations of an extended screw dislo~ation,'~ or by clustered groups of solute atoms whose net elastic stress field is unsymmetric. The purpose of the present work was to investigate various mechanical properties of the Ni-Co-C a1loy system which are sensitive to pinning effects in order to delineate the specific pinning mechanism of carbon. Carbon concentration, grain size, temperature, and strain rate were varied so that thermal-activation analysis and the Hall-Petch analysis could be used to evaluate the pinning mechanism. Cobalt was added to lower stacking fault energy so that the number and extension of split, screw dislocations would be increased in order to test the possibility of pinning by carbon at extended screw dislocations. EXPERIMENTAL PROCEDURE Nickel and cobalt (both 99.98 pct-. pure) were melted with graphite in stabilized zirconia crucibles and cast at lo-' Torr to form Ni-C and Ni-60 pctCo-C alloys. Two ingots were heated to 1250°C and were forged to 1-in.-sq bars. These bars were machined to 4-in.-round bars, and then swaged cold to 0.144-in. -diam rods. Reductions in area of approximately 75pct were used with intermediate anneals at 900°C for 1 hr. The carbon content of batches of 0.144-in.-diam rods from each ingot was reduced to two levels by annealing 5-in. lengths in palladium-purified, dry hydrogen at 1100°C for 25 and 100 hr. The remaining material from each ingot was annealed at 10"5 Torr for 1 hr at 1100"~. These treatments gave a total of three carbon levels for both the nickel and the Ni-60 pct Co alloy. The 0.144-in.-diam rods were swaged to 70-mil wire, cut into test specimens, and then re crystallized at lom5 Torr in capsules for 1 hr at temperatures ranging from 760" to 1050" ~. The capsules were broken and the specimens were immediately quenched into water. Average grain size was measured using Hilliard's method of circular intercepts." Annealing twin boundary intercepts were counted in addition to grain boundary intercepts to establish an average grain size. Average grain sizes ranged from 5 to 140 p depending on the cobalt concentration and re-crystallization temperature. Tension tests were made in duplicate at various temperatures at a crosshead speed of 8.34 x 10"4 in. per sec with an Instron Universal Testing Machine. Specimens of 1-in. gage length with soldered ball ends were used at atmospheric and cryogenic temperatures. Pinch grips were used on specimens at elevated tem-

Jan 1, 1969

By O. J. Hassel, W. T. Maidens, J. H. Calbeck

The rotary gas fired reheating furnace used by the American Zinc Oxide Co. at Columbus, Ohio for Therotarygasfiredreheatingfurnacerefining lead-free zinc oxide is described. The outstanding features of this operation are that the color of the zinc oxide is greatly improved, sulphur is eliminated, and cadmium arethatrecovered without densifying the product to an objectionable degree. IN 1919 Leland S. Wemple obtained a patent for a process of reheating zinc oxide wherein the "coarsening of grain due to excessive heating was avoided." He taught in his specification that if solid carbonaceous material, such as lamp black, was added to the zinc oxide in proper amounts prior to reheating, objectionable sulphur compounds could be removed and the color would accordingly be improved and no objectionable densification would occur because of the relatively low temperature required. The situation that made this invention imperative was the newly opened zinc oxide plant of the American Zinc, Lead & Smelting Co. in Hills-boro, Ill. This was one of the early Western Type American Process zinc oxide operations. Characteristic of all of these early Western operations using Tri-State and Western ores was the great difficulty encountered in obtaining a product low enough in sulphur to compete with the Eastern Type American Process zinc oxides which were made from ores containing very low sulphur percentages. Wemple demonstrated that the refining process of his invention produced a superior color and although this was true and a most welcome feature, the primary purpose of the early refining operations at Hillsboro was to reduce substantially the high sulphur content of the crude zinc oxide. Although many and varied attempts had been made for refining zinc oxide none of the processes had a commercial history of any consequence until Wemple's invention became standard practice for the American Zinc, Lead & Smelting Co. in 1919 and their operations have been unique in that substantially all of their lead-free zinc oxide has been reheated since the first installation at Hillsboro. This process has become known in the industry as refining. The furnace developed by Wemple and continued in use by the company from 1919 until 1943 was unusual and merits some consideration by way of review in this paper. The furnace was essentially a double hearth coal-fired muffle furnace with a mechanical raking system consisting of a central shaft supporting six rabble arms in each muffle. The untreated or "crude" zinc oxide was fed onto the outer rim of the top muffle, moved to the center where it dropped to the lower muffle and progressed to the outer rim where it was discharged into an alloy screw conveyor. The retention in this furnace was extremely short, about 5 min, and the shallow zinc oxide bed on the hearths of the muffles was being continuously turned by the fast moving rabbles. Soft coal was burned on the grates below the lower muffle and the long yellow flame necessary to carry the heat around both muffles resulted in a very inefficient combustion of the fuel. The temperature of the top of the lower muffle seldom exceeded 65 °C although the oxide itself often reached 700°C before discharge. The capacity of this furnace was approximately 1/2 ton per hr. In our plant at Columbus it was necessary to keep four of these furnaces running in parallel to take care of the production because, as mentioned above, every pound of zinc oxide produced during these 24 yr passed through one of these refining furnaces. An essential part of this refining operation was the use of carbonaceous material admixed with the zinc oxide fed to the furnaces. Between 1 and 2 pct of a bran produced in the processing of cotton seed was added to all zinc oxide charged to the furnaces. The bran ignited on the top hearth and was still burning when the charge fell from the top hearth to the bottom hearth making a cascade of sparks. The rapid turning of the zinc oxide caused these particles of bran to flash on the hearths behind each rabble; but the combustion, of necessity, had to be complete by the time the charge reached the outer rim of the bottom hearth, otherwise the finished product would be contaminated with the charred particles of bran which would give the zinc oxide an unsatisfactory color. Although this operation was initiated to reduce objectionable sulphur percentages, as time went on new properties of the product were appreciated which made advisable continuing the refining process long after other methods of sulphur reduction became known in the industry. The particle size and particle size distribution, the absence of colloidal fines and perhaps a unique surface condition gave this product an outstanding performance when used in paints. The Wemple furnaces installed in Columbus in 1919 had to be rebuilt frequently and were extravagant in the use of fuel. The raking mechanism and the muffles required excessive maintenance expense and as the furnaces wore out the problem arose whether to continue along this line or to explore the possibilities of obtaining similar or better results in the simpler and more commonly used rotary furnace. To this end special research was initiated in 1941 on a small laboratory rotary

Jan 1, 1951

By Frank Firmstone

It is proposed to consider here only comparisons made between results obtained when the materials employed are precisely the same, two furnaces at the same works for example, or the same furnace under different conditions as respects temperature of blast, method of charging, etc. With this limitation, the most important point in the comparison is the amount of fuel consumed per ton of iron. This, in fact, is the only item in the prime cost of the iron which can properly be said to vary in consequence of changes in the furnace process; for of the other principal items, the ore used per ton of iron, and also the amount of fluxing material, will depend on its richness, which, under the assumed conditions, will be practically invariable when taken over any considerable period; the labor cost also, from its nature, should be very nearly constant when estimated on the ton of iron. Moreover, as it consists principally in handling and moving material, it is greatly affected by circumstances quite independent of

C. A. Stetefeldt, Oakland, Cal.: It has always been assumed by the writer, and also by others, that the silver volatilized by roasting in a Stetefeldt furnace was a minimum as compared with roasting in other furnaces. Now, Mr. Morse records at

Jan 1, 1896

By A. C. Stevenson

THE hoisting equipment selected for use at the Hecla mine in 1907 was one of the first Ilgner type Ward-Leonard controlled hoists put into ser- vice. Development of the Hecla below the 2000-ft. level, which is the ultimate depth of the old equipment, and the additional service required by the "Star," necessitated additional hoisting capacity. It will be our endeavor to give j70u a brief summary of the engineering which determined the selection of the new equipment. The engineer in making his decision as to size, speed, etc., must .make a duty study approximating as closely &s possible the actual opePating conditions which will eventually result. Primarily, it is necessary to know what work must be done. The amount of material which must be hoisted under the maximum condition, as well as its distribution from the various levels of the mine was carefully studied by the mining engineering department, as the ore reserves, their relative-position and the probable method of working them had to be considered. The final figures reached, taking into consideration four different operating conditions, were, in tons per day, as follows:

Jan 1, 1930

Jan 1, 1966

Jan 1, 1940

Jan 1, 1904

Jan 1, 1965

Jan 1, 1931

No. 243. Superintendent for operating Virginia, manganese mine. One experienced with wet concentration, labor and general management. Opportunity for advancement for right man. Write fully concerning experience, references and salary expected to start.

Jan 11, 1917