Search Documents

By Lyle D. Randen

With the environmental movement beginning in the late 1960's came a deluge of permit requirements for the mining industry. Coal mining has been one of, if not the most, severely impacted of the mineral industries as a result of the passage of the Federal Surface Mining Control and Reclamation Act of 1977. Numerous provisions of this Act and numerous regulations developed under authority of the Act are being challenged in differing levels of the judicial system across the United States. Such court cases have had varied success. Numerous other regulatory programs that are not quite as dramatic as the SMCRA have presented an unending regulatory problem for mining operators. My comments in this presentation relate primarily to the major Federal and State agencies and their legal responsibilities which we in the coal mining industry must address in order to receive authority to construct and operate surface coal mines in the State of Wyoming. A list of the Federal and State agencies one could deal with in an application is as follows: 1. Bureau of Land Management (BLM). BLM is responsible for deciding where and when to lease federally owned coal and for establishing terms and conditions for leases. BLM also has some control over surface reclamation on federal land, i.e. regrading to eliminate highwalls, covering of spoils, maximum extraction of coal to limit future disturbance, contemporaneous reclamation, etc. BLM is also responsible for designation of federal lands unsuitable for all or certain types of surface coal mining operations. 2. Geological Survey (USGS). USGS coal mining responsibilities apply only to Federal and Indian lands and concern compliance with production requirements including diligent development, minimum production levels, royalty payments and resource protection, and

Jan 1, 1983

By P. H. Scott, Walter Rose

Recent papers by S. T. Yuster have called attention to the largely ignored concept that there will be a transfer of viscous forces across fluid-fluid interfaces during the flow of immiscible fluid phases through porous media. This leads to the implication that the relative permeability us saturation function, as applied to each of the fluid phases of the system, will in some way be dependent on the viscosities of all the other fluid phases which are contiguous to the flowing fluid of interest. In fact, Yuster has selected and analyzed the properties of a capillary-tube model of the reservoir-prototype flow systems and concludes from his studies that relative permeability values will be very markedly influenced by the viscosity ratio in two-phase systems. On the other hand, relative permeability data have been reported in the literature for more than 20 years; and where these data are consistent at all, they consistently how no dependence on viscosity ratio (cf. chapter 7 of Muskat3 for a resume of past experiniental work). This paradoxical situation has prompted us to re-evaluate Yuster's work. The major flaw we find has to do with the properties of the model Yuster employed to give qualitative support to his predictions. This model is defective in that important surface area parameters characteristic of the prototype-reservoir flow system have not been propertly scaled. Fig. 1 shows how we believe Yuster's model should be modified to circumvent this difficulty. It depicts the capillary tube of radius R and length L, comprised of two elements in series. The first part of length, L has the nonwetting phase flowing centrally out to a radius distance r, where an interfacial boundary exists with the wetting phase which flows in the concentric annular pace of the tube. The second part of length, L-L,. has the

Jan 1, 1953

By D. A. Farmen

INTRODUCTION In early 1978, engineering personnel at The Carter Mining Company began using photogrammetry coupled with a computer modeling technique to aid in mine planning efforts. The decision to develop this approach was based on the following needs: 1. A method to accurately capture excavated quantities for reporting purposes, 2. A method to produce accurate up-to-date maps for planning purposes, and 3. A computer-based mine-planning technique that would be compatible with techniques used in the past. The system developed utilizes a photogrammetric contractor to provide thousands of aerially-surveyed data points for input into the computer system. Each month the Rawhide and Caballo mines are flown by the photogrammetric contractor. The terrain of the active pit area is digitized and punched out on computer cards. This information is read into The Carter Mining Company's computer facilities, and an updated two-dimensional topographic grid model of the pit is generated. This surface is used to generate quantities moved during the month, to update isopachs, and to update quantities contained in fixed block progression polygons used for forecasting purposes. The system has greatly reduced the amount of manhours spent in field surveying and provides a useful tool for expeditiously evaluating many different forecast cases. It also provides the

Jan 1, 1983

By Joseph C. Buchen

In principle, productiorl of salt from sea water is a simple operation. The sun and wind cause evaporation of sea water trapped in ponds, and what is left is principally salt. Commercial production, however, requires consideration of many factors. First is a high consistent annual rate of evaporation, as well as large areas of suitable low-lying ground close to economical shipping facilities. The south end of San Francisco Bay has these requisites. Large ponds are built, by using clamshell dredges to build up levees to a height of approximately 3 ft. on ground usually lower than sea level, so that the water may be taken in through tide gates without pumping. Ponds are divided into extremely large concentrating ponds and smeller crystallizing ponds. Approximately ten times more area is required for concentrating than for crystallizing. The concentrating ponds are irregular in shape and size but the crystallizing ponds are rectangular and fairly regular in size, to aid in harvesting. The ocean water is taken into the first of a series of concentrating ponds and gradually moved forward from pond to pond as it increase:: in density, reaehing the crystallizing area as a saturated brine. This brine is pumped into the crystallizer at the beginning of the net evaporating season, usually in May, and further evaporation causes its sodium chloride content to deposit on the bottoms of the ponds. The brine must be drawn off and a fresh supply added from time to time to prevent other undesirable salts from depositing with the sodium chloride. Harvesting usually begins near the end of August and now is accomplished almost entirely by mechanical means. After harvesting, the salt is stored in large sbockpiles until required for shipping or refining. The greatest amount is used for industrial purposes and is shipped without any processing other than screening, but all salt for domestic use produced by the Leslie Salt Co. is refined by the racuum process, giving a produet consistently testing over 09.9 per cent sodium chloride.

Jan 1, 1938

By Colin M. Sargent

THE electron diffraction pattern as seen in the electron microscope represents an approximately plane section of the reciprocal lattice. Identifying the zone axis of a diffraction pattern is often laborious for a crystal of low symmetry, especially if several crystal orientations are present. A program has been written in FORTRAN II (Version 2) for the IBM 1620 which will assist in plotting out reciprocal lattice sections. The calculation is performed by choosing a zone axis [uvw] and determining the d spacings and angle between the planes (Ow - v) and (wO - u). (This procedure is varied slightly for zone axes with Miller indices equal to zero.) Cartesian coordinates for the reciprocal lattice points are then calculated for these planes and for (ww— [u + v]). Any reciprocal lattice points within the parallelogram formed by the origin and these three points are then computed. The input and output are best described by use of an example (Monoclinic ZrO2) used in the author's work. Input consists of two cards: 1) The crystal parameters: a, b, c, a, 8, y, e.g., 5.1477, 5.2030, 5.3156, 90.000, 99.380, 90.000. 2) Three numbers, D, E, F, e.g., 5, 3, 3.0710-the first is the limit of the sum (u + v + w) considered; the second limits the absolute value of u, v, and w to (E- 1), e.g., 2, so that zones (221) would be the highest order considered in this example; the third, F, is the required constant, yL. Output is in the format shown in Table I. The reciprocal lattice sections may then be plotted on standard graph paper and compared with the unknown diffraction pattern. (Note that no attempt has been made to deal with systematically absent reflections.) A card deck for the program is available from Colin M. Sargent, ARZ, W-PAFB, Dayton, Ohio, 45433.

Jan 1, 1969

By W. F. Tanner

A river delivers a given load of sand, and hence heavy materials, into the sea. The load is fixed by drainage basin characteristics and processes. Wave energy available for redistributing that load is fixed in an entirely different way. An equilibrium diagram of these two parameters (load vs energy) pennits a tentative prediction of what will happen to the heavy minerals. Alluvial rivers transport a mechanical load which consists essentially of wash load (finer than about 0.05 mm in particle diam), bed load (coarser than about 0.10 mm) and the transition sizes in between. A few rivers carry no appreciable mechanical load, and are excluded from this discussion. An example of the latter is the Suwannee River of Florida, which empties across an oyster bar into the Gulf of Mexico and does not build a delta despite the absence of significant waves or currents in that part of the Gulf. An alluvial river may deliver its load into a protected sediment trap (such as an estuary, sound or lagoon), onto a low-energy coast (where it builds a delta) or onto a high-energy coast (from which spot the river load is swept away). The nature and disposition of the load depends, obviously, on three sets of factors: 1) drainage basin characteristics and processes, which determine quantity and make-up of the load; 2) coastal structure and geomorphology, which determine the kind of river-sea coupling which

Jan 1, 1962

By M. T. Abasov

The work suggests an approach to the problem of optimally planning the drilling and development of gas fields. The approach is based on systems analysis and allows a joint optimal choice of the total number of wells in the field, their spacing in the reservoir, the diameter of production tubing, drilling dynamics, the number and spacing of drilling platforms and well pattern schemes for each plat- form as well. The optimal solution satisfies the set of technical- economical requirements and provides a minimum value of discounted total expenditures (capital costs plus operating costs). A mathematical model of the problem is presented. This work represents an extension of the authors&apos; previous investigations that formulated and solved problems of optimal drilling of oil and gas deposits by directional wells [1] and problems of optimal control of the number of active wells in multi-reservoir oil and gas fields [2], [3]. For construction of the mathematical model we choose a range (Nmin, Nmax) of possible values of the total number of wells, N, which should be drilled in the deposit. Here Nmin, Nmax are minimum and maximum numbers of wells correspondingly, that should be drilled into the reservoir. N[€](Nmin = N1, ... N[o], ..., Nm = Nmax). For simplicity a one-reservoir gas field is considered. It is assumed that: (a) wells are spaced in the reservoir uniformly, (b) there is a certain algorithm providing a uniform spacing of the given number N[o] ([0]=l, . . . , m) of wells in the reservoir, (c) the diameters of the production tubing for all the wells are the same. The relation Qz (x), i.e. the dependence of the cumulative output of gas from the cumulative "well-years" of operations is constructed for each diameter dZ from the given range of diameters d1< ...< dr.

Jan 1, 1977

By R. W. Ph. D. Raymond

PROFESSOR W. P. BLAKE, in a note to his Catalogue of California Minerals, pointed out that the mining districts of the Pacific slope are arranged in parallel zones, following the prevailing direction of the mountain ranges. This interesting generalization has been more fully illustrated and connected with the geological history of the country by Mr. Clarence King, who sums tip the observed phenomena as follows: "The Pacific coast ranges upon the west carry quicksilver, tin, and chromic iron. The next belt is that of the Sierra Nevada and Oregon Cascades, which, upon their west slope, bear two zones, a foot-hill chain of copper mines, and a middle line of gold deposits. These gold veins and the resultant placer mines extend far into Alaska, characterized by the occurrence of gold in quartz, by a small amount of that metal which is entangled in iron sulphurets, and by occupying splits in the upturned metamorphic strata of the Jurassic age. Lying to the east of this zone, along the east base of the Sierras, and stretching southward into Mexico, is a chain of silver mines, containing comparatively little base metal, and frequently included in volcanic rocks. Through Middle Mexico, Arizona, Middle Nevada, and Central Idaho is another line of silver mines, mineralized with complicated association of the base metals, and more often occurring in older rocks. Through New Mexico, Utah, and Western Montana lies another zone of argentiferous galena lodes. To the east, again, the New Mexico, Colorado, Wyoming, and Montana gold belt is an extremely well-defined and continuous chain of deposits." These seven longitudinal zones or chains of mineral deposits must

Jan 1, 1873

By William Fink

MANY investigators have attempted to determine the true nature of the internal changes taking place during aging. Merica, Waltenberg and Scott1 were the first to propose a theory of age-hardening. They attributed the age-hardening of duralumin to the precipitation of minute particles of the compound CuA12. Later Zay Jeffries and R. S. Archer2 augmented the above theory by suggesting that the small CuA12 particles acted as "keys" causing "slip interference." Many other investi-gators3 have devoted much time to the mechanism of age-hardening, some corroborating the "precipitation" and "slip interference" theory, others coming to different conclusions because of effects that to them seemed unexplainable by the early theories; e.g., the increase of electrical resistance upon aging, the fact that no change in lattice parameter could be detected during the early stages of aging even at elevated tempera-tures, and the fact that the density did not change as would be predicted. In 1932, Merica revised4 his earlier precipitation theory to take care of these presumably anomalous effects. This revised theory, the "knot" theory, assumes that substantial age-hardening occurs before actual precipitation of solute as discrete particles. The assumed mechanism is one of diffusion of solute atones into groups forming distorted regions which act as "hard" spots and cause slip interference. These "knots" are assumed to have approximately the same lattice arrangement as the solvent.

Jan 1, 1936

By Jose M. Sobral

The approximate production of petroleum in the various fields and for the country as a whole is shown in the following table, the figures for the later months of the year being estimated. Among the developments of the year may be mentioned the finding by the Standard Oil Co. of a small production, about 6290 bbl., at Aguas Blancas in the Province of Salta near the Bolivian border, and of about 88,000 bbl. at Lomitas, near Tartagal in the same province. The Government (Yaciementos Petroliferos Fiscales) in the last four months of the year also obtained about 6290 bbl, from Quebrada Galarce. .The oil found in Salta is of good grade and while the quantity is small great hopes of larger production are entertained. Approximate Total Argentine Production for 1928 Barrels Barrels Comodoro Rivadavia............................... 8,165,615 Plaza Huincul..................................... 783,514 8,949,129 Distribution of Production Government, Comodoro Rivadavia................... 5,165,159 Government, Plaza Huincul......................... 306,166 5,471,325 Private, Comodoro Rivadavia....................... 3,000,456" Private, Plaza Huincul............................. 477,348b 3,477,804 a The companies represented are Astra, 649,474 bbl.; Oriente, 42,237; Ferrocar-rilera, 1,337,380; Comp. Indust. y Comm., 609,092, Solano, 64,158; Diadema, 298,114. b Standard Oil Co. and a few smaller companies, Exploratory drilling has also been conducted around the Comodoro Rivadavia field. The Government is drilling at Vuela del Senguer south of Colonia Sarmiento and about 200 km. west of the main field hut the prospect of success is not as yet large. The country around Castillo, where the Royal Dutch Co. has property, is regarded more favorably. perhaps the most interesting event of the year was the discovery of a productive horizon at Comodoro Rivadavia about 200 m. below that previously exploited. This new horizon was found by the Ferrocarrilera Co. at 769 m. in its well No. 81, the previous yield for this

Jan 1, 1929

By F. J. Tuck

THE Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a 3/4-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 clays. Manganese-steel lifter bars, 3 5/8 in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 clays. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1 1/2 -in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood hacking is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots; and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 2.5 to 33 per cent of the ore. Addi-tional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department.

Jan 1, 1938

By J. F. Myers, F. M. Lewis

IN the mining and handling of sulphide ores, some degree of oxidation takes place on the sulphide surfaces, which are exposed to the atmosphere. It is, moreover, well known that the oxidation compounds formed are a factor when such ores are subsequently treated by flotation. Modern operating technique and reagents are capable of contending with this condition to a major degree, provided that the proportions of the reagents used are varied correctly. This is particularly true at the Tennessee Copper Co., where the ore treated contains pyrrhotite in addition to other sulphides. A number of soluble salts, some of which are unstable, can be formed during the oxidation of the sulphide ores. Those unstable salts, whose oxygen requirements are unsatisfied, are constantly changing to more stable forms because oxygen reacts with them during the crushing, grinding and other operations of ore preparation. We add no chemicals of any kind to the ore pulp in its preparation for flotation feed. Consequently the only compounds that are present in the flotation feed are those produced by the natural oxidation of the ore in the presence of air and water. The Tennessee Copper Co. ore is composed of from 60 to 70 per cent sulphides and from 40 to 30 per cent nonsulphide material. It is not the purpose of this paper to discuss the nature of these various oxygensulphur compounds nor their effect on flotation, but to describe a method for [ ] correcting the effect. Suffice it to say that we have found that the reducing sulphur and oxygen salts have a depressing action on our bulk flotation process.1 From long experience we find that the best means of correcting for this variation in our work is to increase or decrease the quantity of xanthate, the promoting agent, as the quantity of the reducing salts increases or decreases. It was, therefore, very desirable to provide the operators with some quick and

Jan 1, 1946

By John M. Lovejoy

I take pleasure in transmitting herewith "Petroleum Development and Technology in 1927," in which we have attempted to set out in a series of 40 papers with attendant discussions the advances made in Production Engineering and Refinery Engineering during the year. The volume also contains a digest of round table discussions on Petroleum Engineering Research problems and Petroleum Engineering Education. In addition to the above we set out in 16 papers a review of production of each producing area of the United States and of the more important foreign countries, together with a review of the world&apos;s production and forecasts for 1928. We also include 8 papers on the Economics of the oil industry. The papers and discussions included herein represent the contributions of more than 200 engineers, including the foremost in each line. These papers were presented at technical sessions held in Fort Worth in October, 1927, and at the annual meeting in New York in February, 1928. We desire to express our thanks and appreciation to all those who have contributed to this volume. As in previous years, we have attempted to emphasize the value of both written and impromptu discussions. -We have made a practice of returning all impromptu discussions to the authors for correction and amplification, and because of this practice we feel that the discussions contained herein are in very presentable and readable form. It was decided by the nominat,ing committee when meeting for thc purpose of nominating officers for 1928 to eliminate the vice-chairrnanship for Transportation Engineering, as that branch of the industry seemed to come more naturally under the activities of the American Petroleum Institute. It was also decided by this committee to institute a new vice-chairmanship for Petroleum Engineering Research. Wc have had heretofore round table discussions on engineering research, but through the newly created vice-chairmanship, to which Mr. L. C. Uren was elected, we expect to have more comprehensive sessions on engineering research than heretofort.

Jan 1, 1928

By O’Brian. Daniel T.

Ore reserve determinations supporting property appraisals and economic analyses leading to investment decisions typically require many repetitive calculations. Computers have become well-accepted tools for accomplishing these computations, and are partly responsible for the development of new evaluation methods during the last decade. Excellent descriptions of manual ore reserve may be compared with current computer reserve methods1,2 in North America2 and South Africa3. A comparison indicates that computers are used in two cases: a) when a cost savings can be achieved by the simple conversion of a manual method to a computer processed equivalent, and b) when the quantity of data and ore reserve estimation purpose justifies adoption of a complex ore reserve computational method not feasible on a manual basis. Ore reserve computations essentially consist of using sample data and a mathematical method to arrive at an estimated geometry, tonnage, and grade for a mineral deposit. The mineral deposit is then subdivided, if necessary, into ore and waste components. This separation is based on economic factors which may be explicitly introduced in the computation or incorporated in a numerical cutoff grade4. Computer methods for accomplishing these tasks are presented in three papers. "The Use of Contour Surfaces as Predictive Models for Ore Values" discusses the requirements for a satisfactory value prediction model and the importance of considering auto -covariance. A weighted moving average method is described and compared to other mathematical surface development methods. In the second paper, "The Applications and Limitations of Computer Techniques in the Evaluation of Hypothermal Tin Lodes," particular problems encountered in estimating geometrically erratic economic deposits with a low valuable mineral content are documented. Economics and probabilistic concepts are introduced, allowing a comparison of risk and speculative value for a deposit. Economic considerations are integrated with ore estimation techniques in the third paper, "Method of Calculation of the Iron Ore Reserves in the Lorraine Deposit." The prediction model

Jan 1, 1969

By Charles A. Colton

(Read at the Amenia Meeting, October, 1877.) THE results of a series of analyses extending over a period of three weeks at the Cedar Point Iron Company&apos;s furnace, Port Henry, New York, are given in Tables I and II. This furnace uses a very pure magnetite and Lehigh and Lackawanna anthracite. The flue leading the gas from the "down-comer" to the boilers was tapped by a a inch gas pipe, which carried the gas to the Orsat apparatus. The pressure of the gas not always being sufficient, owing to the small amount made, to force it into the apparatus, I omitted taking samples several days, and with the exception of the last three days of the campaign, made the analyses whenever opportunity offered. I find the Orsat apparatus, as described by Prof. Egleston,* to work very well, with one exception. The CO is not absorbed as readily in the ammonia-copper solution as he states in his description of the apparatus, as many as 50, and sometimes 60, passes being necessary to absorb all the CO. The power of absorbing rapidly increases as the solution is used, and this would indicate that the more oxygen it contains the quicker will it do the work. Probably the addition of a small amount of some oxidizing agent would remedy this. When the furnace was working in its normal condition, I had no occasion for using the filter, the amount of fume being so small as not to cause any inconvenience. The gas burned with the flame peculiar to CO, and contained just enough solid particles to give it a slight reddish tinge. * See Transactions, II, 226; V, 487, 621.

Jan 1, 1878

By H. C. George

At the annual meeting of the Institute in February, 1927, we had a comprehensive discussion of Petroleum Engineering Education. This discussion covered basic training and prerequisites, laboratories and equipment, graduate courses, availability of lecturers, geological engineering, petroleum production engineering, refinery engineering, transportation engineering and economics and management. However, there are several phases of petroleum engineering education, which many members of the Institute felt should be further discussed at this year&apos;s meeting. The first was expressed by me in a letter to those participating in the written discussion, from which I quote as follows: "We fell that the question of handling engineering graduates who enter the petroleum industry should be thoroughly discussed. "During the first five years after graduntion from college, how can these young men be best trained to be of the greatest service to the industry and at the same time do work which will be interesting and of a character which will make them feel that they are accomplishing something and making progress leading toward personal advancement?" Both the written and oral discussion would indicate three groups of opinion; first, those who advocate letting the young engineers go into the industry and take care of themselves without any supervision, direction, or guidance; second, those who advocate the taking of young engineers into the industry and letting them go through all the steps that any laborer or any other mian without a technical education would take, but with some supervision, and third, those who advocate that young cngineers should be given special training for several years after entering the industry. Of course all of these different groups are found in rnost of our industries. The Doherty training school of the Empire Gas & Fuel Co., finds its counterpart in the practice of the Gcneral Electric and Westing-house companies in the electrical industry and the Baldwin and Brooks Locomotive works in mechanical engineering.

Jan 1, 1928

By Richard Dunmore

Tests of the MRDE firedamp prediction method have been carried out in a number of longwall districts with different conditions. The method itself and its development have been described previously At many test sites the prediction has been good, i.e. the calculated gas emission levels have agreed with measured values, averaged over a period of many weeks, within a few percent. In other cases, where there have been larger discrepancies between calculation and measurement, investigations have shown that these may be attributed to particular conditions of mining or geology. Recognition of these conditions in advance of mining is clearly desirable to improve the accuracy of the initial prediction. It has been shown that variations in gas emission rates depend largely on coal production in terms of the weekly advance of the coal face. Although there appears to be a random element present, variations in gas emission levels calculated from changing face advances agree well with measurement. The accuracy of prediction therefore depends on how well face advance can be forecast and needs to be updated as the working proceeds in the light of the face performance actually achieved. Continuous monitoring of the mine environment provides the information necessary to compare actual gas emission with predicted levels, and computerised systems make it possible to carry this out in real time. Predictions can thus be adjusted to take account of emission levels measured in previous weeks These adjustments, whether they are made after the first few weeks or subsequently during the district life, would also be used to alert management to particular abnormalities or significant changes in gas emission.

Jan 1, 1982

By Frank Firmstone

WE found it necessary, in December, 1874, to repair the upper part of the lining in No. 5 furnace at Glendon, and, as we succeeded in doing it with comparatively little trouble, a description of the plan followed may be of service to those having a similar operation to perform. On two opposite sides, as shown by the sketch, the lining was completely gone for a height of about four feet, below which it increased gradually in thickness, being nine inches thick about three feet lower down. On a plane at right angles to the section drawn, the brick were nowhere entirely gone, but were in some places not more than two or three inches thick, being still sufficient to sustain the upper part, where the brick, being above the level of the stock, were not at all worn. The furnace was blown down, so that when we cast and closed the tuyeres, about 7 A.M., on December 8th, the top of the stock was about twenty-four feet below the filling-plates. The walls were quite hot, and a good deal of gas was given off for several hours after the tuyeres were closed. The hopper and bell were thrown into the furnace, and were covered by filling several charges of cold stock over them, which at once greatly cooled off the top of the furnace. A wrought-iron pipe, thirty inches in diameter, in five sections, each six feet long, was then put down, and made to stand upright, as nearly as possible in the centre of the furnace. Around this we filled a double charge of coal, taking care to heap it up next the pipe, and let it get thinner as it got to the walls. This was covered with about two feet of fine ore, leaving the lowest joint in the pipe entirely uncovered. We were now ready to put in our scaffold to get at the

Jan 1, 1876

By L. J. West, R. M. Perrry

This chapter describes the rock mechanics studies performed for a high cut at a nuclear power station in Pennsylvania. Two units presently are being constructed on the Susquehanna River. When these units are completed, they will generate approximately 2100 MW of electricity. It was necessary to excavate about 1 million cu yd of rock to prepare the site. This excavation resulted in a high cut on the west and north sides of the station area with a maximum height of about 200 ft. The location of the high cut with respect to the plant facilities is shown on Fig. 1. The recommended slope angles ranged from 1 ½ (horizontal) to 1 (vertical) for the upper residual soil to ½ to 1 for the deeper competent rock. Because of the significant height of this cut and the fact that the slope is immediately adjacent to the proposed nuclear facilities, extensive stability analyses were performed prior to, during, and after excavation to evaluate the steepest angle at which the slopes could be safely cut. The studies consisted of evaluating both qualitatively and quantitatively all apparent factors which could affect the stability of the slopes. These factors include the strength of the material, the zones of weak material which are present along the planes of schistosity, the prominent joint systems, the ground water, and postulated seismic effects. FIELD AND LABORATORY STUDIES A comprehensive program of field explorations was performed to evaluate the geologic characteristics of this site. This program consisted

Jan 1, 1970

By R. W. Raymond

Prof. Henry Lours, of Armstrong College, Newcastle-on-Tyne, England, a distinguished member of this Institute and other technical societies, has recently sent to the Institution of Mining Engineers, and to the Institution of Mining and Metallurgy, in Great Britain, a communication, the substance of which is as follows : Professor Louis calls attention to the absence of any recognized English term for the definite description of a frequent phenomenon—namely,the oblique position of an ore-body in the plane in which it lies. In this connection, Professor Louis says that in America the term " pitch " has been occasionally applied to this relation, and proposes that, in the literature of ore-deposits, it shall be hereafter restricted to this particular meaning, the angle of the pitch, like that of the dip, being always measured from the horizontal, and the dip being always taken at right angles to the strike, while the pitch is taken on the plane of the dip, in the direction of the strike. Thus, for example, in a vein or bed striking N-S., and dipping, say, 45&apos; E., there might be an ore-body, the axis of which pitched northward, at an angle of 45O below the horizontal line, as measured on the plane of the inclosing vein or bed. If&apos; the term " pitch " had this universally recognized meaning, the situation could be simply and perfectly expressed by its use, in connection with the general data of strike and dip. As Professor Louis says: "This suggestion has a certain practical value, and is not merely academic. Every mining engineer of practical experience in such types of ore-deposit will have met with cases, in which a vertical shaft has been sunk with the object of cutting the deposit, but has missed it, because the dip alone has been taken into account, while the pitch has been overlooked." He adds the acute observation that such an oversight is much likelier to occur with regard to a condition not definitely desig-

Jan 1, 1909