Search Documents

By Janshi Sen

Vertical-intensity magnetometers, for instance the Hotchkiss Superdip and the Askania vertical field balance, are now widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. I, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1946

Mr. Raden has described the practical problems associated with fines in phosphate rock beneficiation. In this discussion, a colloid chemical viewpoint is given to the problem of separating phosphate values from phosphatic clay slurries. The phosphatic clays are predominantly colloids of a complex mixture of many minerals (1). The constituents are typically 25% apatite, 40-50% clays, and various amounts of wavellite, quartz, dolomite, fluorite, and other minerals. The clays are montmorillonite, attapulgite, and illite, with some kaolinite. The various mineral colloids in the slurry are heterogeneously coagulated in the as-produced state. Dispersion of the coagulated state is evident from the fact that dispersing agents (certain polyelectrolytes) cause a large reduction in the viscosity of the slurry (2). The as-produced slurry settles from 4 to 8% solids within a week, but thereafter settles much more slowly in the form of a sediment of flocs. The supernatant liquid is often clear because of the cooperative action of the mutual interaction of particles during settling. Mineral segregation during settling has not been observed for the same reason. The initial slow settling rates indicate that the coagulated assemblies are very small. Efforts to separate apatite from the other minerals would be complicated by the heterogeneous coagulation state. Somehow the apatite must be "liberated" from its association with the other minerals before it can be physically separated. One approach for liberating apatite is to disperse the entire suspension. While this is feasible technically, for example by using certain polyelectrolytes (2), the reagent costs based on present

Jan 1, 1979

By Byron E. Eldred

Generally speaking, the practical study of combustion has been made mainly from the stand-point of the steam engineer. This narrow view-point has left open a large field for scientific research on the application of combustion in other arts, where the conditions of heat-utilization are widely different from those presented in the steam-generator. The great economic importance of the boiler and the ease of measuring its performance, together with the comparative uniformity of conditions in the steam-generator, is, probably, quite largely responsible for the practical neglect of the study of the use of fuels in other arts save only on the basis of their thermal value. yet these other arts show quite plainly that a thermal-value basis alone is not sufficient. For example, in burning lime, under ordinary conditions of firing, a cord of wood will do as much work as a ton of coal, though the latter affords more than twice the number of heat-units. Similar results are evidenced in burning brick, in the roasting of certain ores, in reheating billets, and in many other, arts where heat is to be applied over extended areas to fragmental masses of more or less refractory materials. In these arts much is to be gained by a

Jan 1, 1911

By Sandford S. Cole

Manganese compounds occur in many mineral forms widely distributed throughout the crust of the earth. The most important of these commercially are the oxides which are usually found as irregular masses, but in some places (notably U.S.S.R.) occur as extensive beds of varying thickness and purity. The principal sources of ore have been U.S.S.R., Ghana (the Gold Coast of Africa), India, Union of South Africa, Belgian Congo, French Morocco, Cuba, Brazil, and Mexico. New developments of ore are being conducted in Brazil, British Guiana, French Equatorial Africa, and Northern Rhodesia. The production of the United States normally meets less than 10 pct of domestic manganese consumption. Manganese ore (35 pct or more Mn) is used principally by the ferrous metallurgy industry for production of manganese metal, ferromanganese, and other manganese alloys for use in production of steel ingots and castings. Some manganese is used in the nonferrous industry as an alloying element and cleanser in aluminum alloys, aluminum bronze, constantan, manganese bronze, Monel, Everdur, nickel-chromium resistance alloys, and nickel-silver. The metallurgical uses consume about 97 pct of the total manganese ore requirements of the United States. The balance goes principally for the manufacture of dry cells and for chemicals, with limited amounts for ceramic products, plastics, welding rods and varnish. The Materials Survey on Manganese, compiled in 1952 for Materials Office National Security Resources Board by the Bureau of Mines and Geological Survey, provides an excellent review of resources, reserves, specifications, uses, mining, beneficiation, metallurgical processes and deposits, and is worth referring to for greater details. Mineralogy and Geology The more common manganese minerals with typical characteristics are listed in Table 1 in order of importance. [ ]

Jan 1, 1960

By Robert C. Meaders, Arthur R. MacPherson

Many attempts have been made to eliminate most of the crushing plant and all the grinding plant in the process of ore beneficiation by substituting a combined crushing and grinding unit which could take coarsely crushed ore and reduce it to a fine size in one unit. This unit normally would have no other grinding media than the ore itself. This is true autogenous grinding, as we understand it today, and should be clearly distinguished from pebble mill grinding, where pebbles are substituted for steel balls to grind a ball mill size feed. To compete in efficiency with normal methods of crushing and grinding, the autogenous mill must use less labor and steel to produce an equivalent product at equal or lower power consumption. In general terms, a unit to perform these functions must have means to crush the ore to fine sizes and to then further reduce the crushed pieces by grinding. In other words, to do efficient autogenous grinding, there must be a proper balance established between crushing and grinding rates. There is not much point in crushing at too fast a rate if the grinding means are not present to reduce the small particles to the required product size. The crushing means used in an autogenous mill are impact forces of two kinds, namely, (1) the rock travelling at high speeds striking the shell, and (2) the lifters travelling at high speeds striking the rock. Grinding is probably effected in a manner equivalent to pebble milling.

Jan 9, 1964

By David J. Mack, Chin Bea Kim

The decomposition of the Ni-Zn eutectoid at 56 wt pct Zn was studied by isothermal transformation. Its progress was followed by metallographic, hardness, and X-ray diffraction methods. Three transformation products were found: lamellar pearlite at high temperatures; an intermediate temperature structure; and martensite at the lower temperaCures. No transition structu,ves were found. THE decomposition of the Ni-Zn eutectoid at 56 wt pct Zn was stuadied as part of a long-range program of study on the eutectoid transformation in alloy systems which do not have one or more components which exhibit allotropy. Available information on the Ni-Zn eutectoid transformation is limited to that presented in connection with the determination of the phase dilagram. No systematic studies of the eutectoid were found in the literature, alkhough the microstructures of the Ni-Zn eutectoid were reported by Tamuru.3 X-ray diffraction data exist for the ß, ß1, y , and y1 phases.' EXPERIMENTAL PROCEDURE The eutectoid alloy was prepared from "A" nickel shot and Bunker Hill super-purity zinc (99.998 pct).

Jan 1, 1962

By Maxwell Adams

CONSIDERABLE interest has recently been developed in sage-brush oil because of its possible utilization as a flotation agent in the mining industry. A list of some of its physical properties, together with the method used in its extraction, may prove of interest at this time. Something over a year ago, a study of the essential oils in desert plants was begun in the Chemical Laboratory of the University of Nevada. None of the oils so far studied possess properties of special interest to engineers, except the oil of sage, Artemesia tridentate, which has exceptional power as a flotation agent. This plant, known as common sage brush, also called black sage, is widely distributed over the semi-arid West, being found quite generally on most of the dry plains and mountains west of Missouri. The method of extracting the oil followed in these experiments is very simple. The leaves, twigs and small branches are placed in an airtight drum, having a capacity of about 27 cu. ft. Steam is admitted through a number of small openings at the bottom of the retort, and the pressure maintained at 20 to 25 lb. per sq. in. for 3 hr. The escape of the steam from the retort is regulated by allowing it to pass through a stop-cock into a condenser. The water in the receiver is drawn off from time to time and the oil, which is insoluble and floats upon the water, is thus collected. At the end of 2 hr. most of the oil has been driven out, though traces continue to come over for a much longer time. By raising the pressure, the time required could probably be shortened and the yield increased, but the lack of laboratory equipment has prevented the carrying out of this experiment.

Jan 9, 1916

By Stanley J. LeFond, Neal Davis

Drilling an oil well or most other types of drilling or coring is no longer a simple and uncomplicated operation. Drilling today at depths which exceed 30,000 ft is hazardous and requires personnel with long and varied experience in drilling. It also requires extensive experience and knowledge in the use of materials which are added to the drilling fluid or "mud," more often than not materials utilizing an industrial mineral. The drilling fluid can vary from a simple mixture of water and "mud" to a very sophisticated, scientifically compounded drilling fluid. Industrial Minerals Used in Drilling Fluids Industrial minerals which are commonly used in oilwell drilling and completion are listed on [Table 1]. The most important minerals, determined by sales, are bentonite and barite. The other minerals listed are either used to achieve a specific purpose or are used regularly but in limited quantities. The main suppliers of drilling fluids internationally are Magcobar Div., Dresser Industries, Inc.; Baroid Div., National Lead Co.; IMC Drilling Mud Co., (a subsidiary of International Minerals and Chemicals Corp. and Halliburton Co.) ; and Milchem, a division of Baker Industries. Most of the industrial minerals are found in North America, with barite mines and processing plants located in Nevada, Arkansas, Missouri, and Arizona, and bentonite mines near Graybull, Wyo. Other mines, such as those in Nova Scotia, are capable of shipping to South America and to the European and Middle East countries. Most of the materials processed by any of the suppliers must conform to specifications set by the American Petroleum Institute (API) or the Oil Companies Material Organization (OCMA). These specifications provide for uniform physical and chemical properties of the materials to be sold on the open market.

Jan 1, 1975

By H. W. Turner

Lying to the east of the Rio Grande, in central New Mexico, is a long N. and S. mountain range, broken into separate ridges at several points. These have received separate names; the mountains at the south end, near El Paso, being known as the Franklin mountains, and then, following successively, to the north, the San Andreas range, Sierra Oscura, Manzano and Sandia mountains. At the eastern base of the Sierra Oscura there are several low ridges, remarkable for their red color. All of these red ridges contain reefs of copper-ore. The eastern flanks of the Sierra Oscura are composed of limestone. Some fossils in the limestone were examined by Prof. J. P. Smith of Stanford University, who says they are Fusulina and indicate an Tipper Carboniferous age. The sandstones and shales containing the copper-reefs directly overlie this limestone (Fig. I), and are very likely of Permian age, like the similar beds in Texas, described by Mr. W. F. Cummins.* Overlying the copper-beds are red sandstones and shales in which very little copper has been found. The cupriferous zone and the red sandstones and shales are everywhere associated, and as one stands on a high point, he will see that these rocks form three main belts or lines of hills. These may be referred to as the northern, middle and southern belts. The northern belt was not visited by me, but is known to contain copper-deposits. The middle belt has a trend of N. of W. and S. of E. The copper-reefs have been traced for a distance of more than 2 miles. The southern belt has a trend of about N. 30' W. and S. 30°

Jan 1, 1903

By Albert Williams

A large proportion of the work performed in wet-crushing silver mills is devoted to the handling and re-handling of pulp between the battery and the pans. There seems to be no generally applicable substitute for the settling-tanks, and in the present system of constructing mills the tanks involve an amount of labor which may be regarded as disproportionate and unnecessary, in view of the automatic improvements which have been introduced in other directions. This diffculty has been met, however, by Boss's continuous process, in which the pulp flows directly from the mortars to the first of a series of constantly working overflow-pans. This method has been adopted at the Noonday mill, Bodie, California; the Harshaw, Arizona; the Sierra Grande, New Mexico ; and the Prietas, Sonora. The continuous process, while giving excellent results with special ores, and under peculiar local conditions (such as a deficiency in water supply), is not, I believe, claimed to be available for all raw-amalgamating mills, notwithstanding its well-merited popularity for certain work. Some trouble has been experienced from the tendency to concentration in the pans, though this can be avoided by skilful manipulation. It has also the disadvantage inherent in combinations of distinct operations ; it requires a very nice adjustment of the water supply to obtain full battery efficiency without running the pans too thin, though the latter defect is partially compensated for by the gradual thickening of the pulp as it proceeds through the series of pans. The objection is similar to that which holds in a parallel duplex process, that of combining roasting and smelting in a single furnace, where each operation is injuriously affected by the necessity of fitting it in with another and entirely different one.

Jan 1, 1883

THE RELATION OF THE ENGINEER TO RECONSTRUCTION FIFTY-THIRD MEETING OF BOSTON SECTION The fifty-third meeting of the. Boston Section was held April 28. The speaker of the evening was the new president of the Institute, Mr. Howard V. Winchell, who spoke on "The Relation of the Engineer to Reconstruction." He told of the part engineers had played in the war and paid tribute to Herbert E. Hoover as an example of what engineers can do. He said that engineers are not taking enough interest in politics, although it is badly needed as shown by the evidences of Bolshevism even in America. Conditions have suddenly changed; whereas we formerly borrowed money we are now loaning widely to foreign countries and our investments, abroad have to be protected. A committee is badly needed to investigate and determine the actual conditions. The Government has already been invited to cooperate with the Institute along professional lines and this should lead to closer contact between our Society and the Government. Mr. Winchell then went on to describe some of the mining conditions in Russia. He brought out the point that the rich platinum deposits are exhausted and only the poorer sands remain. The largest copper properties average less than 2 per cent. copper and there are some 4,000,000 tons available in .the Caucasus region near Batum. There are approximately 100,000,000 tons of high-grade manganese ore scattered in small deposits in the eastern Ukraine. There are some copper mines in the East, butt they are almost exhausted. The Baku oil field is the second largest in the world and there is probably oil in Persia. There are also manganese in Siberia and coal veins of enormous thickness.

Jan 7, 1919

By Roger W. Swindle

INTRODUCTION The Uravan Mineral Belt in southwestern Colorado and southeastern Utah is a uranium-vanadium mining district with a unique set of radon daughter control problems. This paper describes these problems and the methods that have been developed to deal with them. The greatest emphasis is placed on the problems caused by air stagnation because these are the most frequently encountered ventilation problems, and this is an aspect of uranium mine ventilation that is often misunderstood. VENTILATION PROBLEMS Most of the mine ventilation problems in the Uravan Mineral Belt are caused by one or more of the following conditions: (1) the highly irregular ore deposits are difficult to locate and delineate, (2) air stagnation occurs in many areas of the extremely irregular mine workings, and (3) it is often necessary to reactivate old workings with small airways that are often caved. Planning Problems Orebodies in the Uravan Mineral Belt are so discontinuous and unpredictable that they are difficult to locate and delineate. Data supplied by surface drilling and underground test holing are often misleading; very little ore may be found in the vicinity of an ore hole, and, conversely, an unmineralized hole may be adjacent to a high-grade ore deposit. Also, ore guides are often ambiguous, and their interpretation is usually a matter of opinion.

Jan 1, 1983

Dr. Wadsworth's discussion of leaching is straightforward and certainly points out some of the critical areas in regards to the fundamental aspects of leaching. I will address myself to the more practical aspects of leaching. As a couple of general comments, very fine particles are often dealt with only when necessary. In many processing applications the sands and slimes are separated with the sand portion being treated by common metallurgical techniques and the slime portion being treated essentially by any technology that will recover some of the values. Ore treatment techniques such as leach/precipitate/float (LPF) have been used in the copper industry to take advantage of leachable copper preferentially reporting to the fine fraction. The second advantage, of course, is the improved metallurgy associated with the treatment of the sand fraction. Cases can be made for sand/slime separations in the aluminum and uranium industry where most of the value reports to the slime fraction and the sand fraction is rejected In the agitated leach systems, fine particles are often the most readily attacked and leached. In dump, vat and in-situ leaching, fine particles cause considerable problems. The fines will tend to restrict the solution flow from portions of the leach feed. This either causes a significantly reduced solution flow or, more probably, the solution will channel, by-passing much of the ore. In either case the result is a decreased metal recovery from ore. The fine particles of principal concern are clays of a flat plate-like shape which can very effectively compact, swell and cause a decreased solution flow. Discrete silica grains or sulfide grains due to their shape, even though they may be very fine, will not cause nearly the problems clays and secondary precipitates can cause.

Jan 1, 1979

At a large meeting of the members of the American Fund for French Wounded it which Mr. Franklin D. Roosevelt presided and at which Mrs. B. Girault Lathrop, President of the Paris Administration A. F.F. W., gave a most interesting address, special rows of seats were reserved for the members of the W. A. A. I. M. E. Those who were unable to be present will be glad to hear that Mrs. Lathrop complimented our organization on having supplied the largest dispensary operated by the A. F. F. W. and the Red Cross in northern France. The A. F. F. W. is going to erect an American Memorial Hospital at Rheims and it is hoped that the one hundred beds in the hospital will be endowed in memory of the men who gave their lives for the liberty of the world. It will be possible not only to endow beds, for which sums of $6000 each are needed, but also to give, as. memorials, sun- parlors at a cost of $10,000 each, two roof gardens at $5000 each, a laundry at $10,000 and a garage at $10,000. The New York Section has undertaken to endow a heel in memory of members of the A. I. M. E. who gave their lives in the Great War. Perhaps other Sections or groups of Sections may wish to do the same thing, or if no other Section cares to assume so much responsibility possibly individuals may like to join the fund already growing in New York, in which case they should send their contributions to Mrs. W. Y. Westervelt, 1 Lexington Ave., New York, N. Y.

Jan 6, 1919

By C. L. Dake

Many proposals have recently been made regarding the broadening of engineering education, often with little consideration of the problems their application involves. The chief purpose of this paper is to point out how many and how complex are the questions that absolutely must be answered, in any conscientious effort to solve the problem of liberalizing engineering curricula. Among proposed additions, more training than is now given has been urged in public speaking, report writing, business law and contra s, general finance, money and banking, scientific management, gene ' economics, economic and financial history, social problems, labor pre lems, public ownership, psychology and similar related subjects. T urge in this direction is widespread and persistent. In discussing the blem, the following questions must be given careful consideration, an he absolutely definite conclusion reached: 1. The Present Curriculum Load.—Is this load actually too heavy? In the face of this load, is there room to add broadening subjects to our curricula? Can elimination of present subject matter make room for such additions? Can an elective system accomplish the desired end? 2. Problem of Early Specialization.—Is early specialization a weak ness? Is industry forcing early specialization? Do our varied degrees demand early specialization? Can broadening be harmonized with the present degree of specialization? 3. Graduate Work to Solve the Broadening Problem.—Can we add the desired work in the graduate school? Are the proposed additions of graduate caliber? Is it desired to reduce graduate standards? Can present undergraduate work be removed to the graduate school, to make room for desired broadening courses? Is graduate work normally broadening, or is it specialization ? 4. Importance of Proposed Additions.—Will they increase entrance salaries? Will they increase the engineer's efficiency? Will they raise

Jan 1, 1934

By Thomas MacFarlane

During the last fifteen years the progress made in the science of lithology has been of a very marked character. From being a miscellaneous collection of facts and observations regarding certain mineral aggregates seemingly incapable of systematic arrangement, it has become a most interesting and orderly department of science. The investigators who have brought about this great change have recorded the results of their labors, and placed at our service an extensive and varied literature on the subject. To this I have paid some attention, and partly from studying it,, partly from my own observations, I have wrought out a classification of original or crystalline rocks, which I venture to bring under the notice of the members of this Institute. The practical importance of the subject will be acknowledged when it is considered that rock species are not without their influence on the contents of the mineral veins which intersect them. Besides, the Institute has been doing good service in defining terms in metallurgy, and no doubt in mining and geology we might

Jan 1, 1880

By S. W. Parr

THE low-temperature carbonization of coal involves the carrying out of the coking process under conditions wherein neither the coal mass nor any of the passageways through which the volatile products pass are heated above 700° or 800° C. For convenience in this discussion, the single number 750° will be used to designate the maximum range. This temperature is not selected arbitrarily; it is the result of certain natural conditions that are inherent in the substances involved. Two of these conditions arc sufficiently pronounced to suggest a line of demarcation at this point as follows: (1) Below 750°, all the heavy hydrocarbons are expelled, which means that, at these lower temperatures, the illuminants, the gases of high calorific value, and the condensible oils are discharged; above 750°, there are given off the lean, non-illuminating gases consisting for the most part of hydrogen and marsh gas and having no condensible constituents present. (2) Below 750°, there is substantially no secondary decomposition; above 750°, the volatile products are readily decomposed, forming tars, naphthalene, free carbon, etc. It is not intended to maintain that no secondary decompositions occur below 750°. Many recent studies have demonstrated the practicability, especially in the presence of catalytic substances, of cracking certain of the hydrocarbon compounds; but at these lower temperatures the step is a moderate one, as, for example, from xylene to toluene or from toluene to an anthracene. These changes are moderate in amount. Not only do the reactions proceed slowly but they are subjected to the decomposing conditions for only a short time. This is evident when it is recalled that at these initial temperatures the decomposition, of the coal is very rapid and, if anywhere near a neutral pressure is maintained, the movement

Jan 2, 1920

By W. E. C. Coxe

AT the meeting of the Institute in Philadelphia, in June, 1876, it was my pleasure to read a paper on the "Manufacture and Endurance of Iron Rails." I then spoke of some trial rails which had been placed in the down track of the Philadelphia and Reading Railroad, over which passed, in addition to merchandise and passengers, most of the heavy coal traffic of that company. One of these rails, made at the Philadelphia and Reading Rolling Mill in 1870, and then placed in the track, was removed in 1876, after having carried about 55,000,000 gross tons, and was on exhibition at the Centennial Exhibition. A piece of this worn rail, twisted cold, was also shown there. One of the same series of rails was allowed to remain in the track until 1878, and short sections of this rail, as well as one not worn, to show its original shape, are presented for your inspection. A comparison of the two will show that the top of the head or tread has worn down 3/16 ths of an inch during its nine years of service. It carried in that time 67,000,000 gross tons of freight, passengers, cars, and engines. This rail was made in the usual way of manufacturing iron rails at the Philadelphia and Reading Rolling Mill. The head was made from puddled iron bars, piled, heated, and rolled into bars, 4 1/2 and 3 inches wide by 1 inch thick, these bars, breaking joints, were made into a pile in section 9 inches square, heated and rolled into slabs 9 inches wide and 2 inches thick; the balance of the rail-pile was made of 4 1/2 and 3-inch bars, rolled from two-thirds old rails and one-third puddled iron, the

Jan 1, 1880

By T. F. Witherbee

AS the forms of blown-out furnaces are of much interest to ironmasters and metallurgists, the manner of taking the accompanying sections of the Cedar Point stack is here given. The diagrams show the original and also the final shape of the furnace after a two years and twelve days' blast,, during which the following solid materials passed through it, viz.: Coal, 41,000 tons; ore, 57,000 tons; limestone, 30,000; total, 125,000 gross tons. Product, 411/4 tons per day Bessemer pig iron. The apparatus used in taking the sections was a modification of that proposed by Mr. Frank Firmstone,* and consisted of a sliding rule, to follow around the circumference of the stack, which rule was connected by a string to a segment of a circle of 24 inches radius. The segment was carried by an arm which connected it to a huh as a centre, 2 inches in diameter. A second string was wound around the hub, and communicated motion to a pencil-carrier, the pencil of which marked out on paper the exact outline, and reduced it to a scale of & inch to the foot. The whole machine was made in about three hours, with the facilities of a carpenter's shop, and gave in operation every irregularity of the lining. The sections were taken at salient points, by lowering a hanging staging on which the apparatus was placed. Tracings from the paper of the machine were made, and, as in this case several copies were required, the tracings were glued on to thin sheets of basswood, and patterns carefully sawed out with a bracket saw.

Jan 1, 1879

By H. R. Payne, A. F. Gorton, H. A. Schwartz

In a previous paper1 we published what we believed to be a correct stable equilibrium diagram for an iron-carbon alloy containing + 1.20 per cent. silicon. The purpose of the present paper is to record the results of studies concerning the effect of silicon on the location of the eutectoid points of both systems, including also certain incidental observations of general interest. We prepared white cast irons containing roughly 21/2 per cent. carbon, 0.05 per cent. manganese, and 0.03 per cent. each of phosphorus and sulfur, but of accurately known silicon contents which varied from 0.40 to 3.32 per cent. These were completely graphitized, and both A1 points determined, as in our previous work, the specimens being converted from the stable to the metastable condition and vice versa by appropriate heat treatments. Each stable alloy was heated to a few degrees above Arl for 3 to 7 hr., quenched and analyzed for total and graphitic carbon, the difference being the "combined" or, better, agraphitic2 carbon content of the saturated solid solution just above the eutectoid transformation. One specimen was lost through accident, and the 0.40-per cent. silicon material gave an anomalous result ascribed to difficulty in maintaining the stable system in the presence of but little silicon.

Jan 1, 1923