Search Documents

By R. E. Reed-Hill, W. H. Hartt

The second order, {1011}-{1012} twin bands observed in critically deformed magnesium are often accompanied by an unusual form of kinking. These kinks, which lie adjacent to and run more or less parallel to the twin band habit, allow plastic deformation that occurs inside the twins to be accommodated into the matrix. The bend planes of these kinks cannot be explained using slip dislocations with Burgers vectors lying in the basal plane. A mechanism involving a single set of {1012)(1011) dislocations is proposed to account for the kink band habit, in good agreement with the experimental observations. It has been shown that second order, {101l)-{1012} twinning is an important phenomenon for magnesium deformed in the ambient temperature range. A detailed study of these twins has recently led to a better understanding of their irrational habit plane1 and their relation to fracture in magnesium.' This paper is concerned with a third aspect of these twins; this being the kink bands, originally referred to as shear accommodation kinks,3'4 that are often induced in the adjacent matrix. A twin band and its shear accommodation kink usually appear as a single macroscopic deformation, as seen in Fig. 1. The complex nature of these deformed regions is easily revealed, however, with the aid of a suitable microscope. It has been proposed374 that the primary function of these kinks is to accommodate the nonhomogeneous deformation that normally occurs in the second order twins. The twins tend to form as small discrete lamellae lined up approximately one in front of the other.''' Very large plastic deformations varying in magnitude from one twin to the next, may occur inside these lamellae. The kinks serve both to pass this strain into the matrix and to accommodate strain variations between twins. Deformation within the kinks, subsequent to their formation, has also been observed;3,4 and it is thought that this contributes to the strain accommodation process. The bend planes of the kinks have a habit near that of the twin band itself, which lies about 56 deg from the matrix basal plane. This orientation does not bisect the angle formed between the basal plane to either side of the bend plane and therefore differs markedly from the kink structure usually observed in hcp metals.'-' The present paper reports the results of a study of shear accommodation kinks and proposes a possible solution to the problem of the orientation of the bend plane. EXPERIMENTAL PROCEDURE Rectangular cross-section tensile specimens with axes parallel to (1010) and faces to (1210) and (0001) were cut and acid machined from a high-purity magnesium single crystal. After straining on an Instron machine the specimens were examined by both optical and replica electron microscopy. The basic procedures have been previously reported."' EXPERIMENTAL RESULTS AND DISCUSSION Structure of Shear Accommodation Kinks. A typical, large (101l)-{1012) twin band with its associated shear accommodation kink is shown running diagonally from upper left to lower right in Fig. 1. In this optical micrograph the twin band, consisting of a row of small, highly deformed twin lamellae, is visible as a narrow dark band along the left hand edge of the structure in question. The kink lies to the right of the twins, is approximately three times as wide, and is lighter in contrast. The horizontal slip lines visible on the general specimen surface correspond to matrix basal slip and are parallel to the tensile axis. Note that on the right-hand side of the band these slip lines can be followed from the matrix into the kink. At the kink band boundary the slip lines suffer a clockwise rotation of about 25 deg. Rotations of this magnitude are not uncommon. When a surface such as that in Fig. 1 is given an etch1 making it sensitive to polarized light, it has been observed that the slip traces in the kink are parallel to the basal plane trace in this region. This is in excellent agreement with the assumption that these regions are indeed kinks. Fig. 2 is an electron micrograph of this same twin band and kink. Note that a row of small supplimation pits has formed

Jan 1, 1969

By H. C. Fiedler

The development of cube-on-edge secondary re crystallization texture in Si-Fe strip depends upon the ability of inclusions, such as manganese sulfide, to restrain nomal grain gvowth. The ability of inclusions to perform this function is shown to depend upon their size and distribution. The desired uniform dispersion of many small inclusions is obtained by controlling the cooling rate from above the solution tempmature of the inclusions or, alternatively, by drastic 'quenching from above the solution temperature followed by heat treating at a lower temperature. The development of the cube-on-edge secondary recrystallization texture in Si-Fe strip depends upon both establishing the proper primary recrystallization texture and having inclusions to restrain normal grain growth. It has been suggested that the first requirement is met with a texture which, though weak, is near (110)[001]. A mechanism for secondary recrystallization originally proposed by ielsen' is consistent with the presence of this primary texture. It is visualized that a secondary grain appears where two adjacent grains happen to be sufficiently similar in orientation to be capable of behaving as a single large grain. This pair of grains will grow at the expense of its smaller neighbors as a consequence of its having lower grain boundary free energy. Other explanations of the origin of the secondary recrystallization texture have been offered,' and it can be concluded that the mechanism is not fully understood. Nevertheless, it is apparent that operationally the necessary primary recrystallization texture is obtained simply by interposing an anneal during the cold reduction to final gage. The role of inclusions in the development of the secondary recrystallization texture has been demonstrated by May and Turnbull4 in a comparison of a high-purity heat and a heat containing manganese sulfide. They showed that the driving force for secondary recrystallization is inversely proportional to the diameter of the matrix grains and that the function of the inclusions is to maintain a small matrix grain size. Other inclusions, such as various sul- fides,')' silicon nitride,8 and vanadium nitride,' titanium carbide,'' and vanadium carbide," have been shown to be effective in promoting secondary recrystallization to the cube-on-edge texture. There is also evidence that silica inclusions in Si-Fe strip made by powder-metallurgy techniques perform this function.' This report is concerned with the second of the two requirements for secondary recrystallization, namely the importance of the metallurgical control of the size and therefore number of inclusions. While the concepts involved are simple, they are fundamental to the making of this material. EXPERIMENTAL PROCEDURE A heat containing 3.27 pct Si, 0.026 pct S, 0.06 pct Mn, and 0.004 pct C was made in an air induction furnace from electrolytic iron, 98 pct ferro-silicon, electrolytic manganese, and iron sulfide. The heat was divided between graphite and baked-sand molds with a cavity 2-5/8 by 5 in. and with walls 2-3/4 in. thick. Slabs, 1 in. thick and 2-5/8 by 5 in., were cut from the ingots and hot-rolled either in the as-cast condition or after one of the heat treatments described later. After pickling, the 80- to 100-mil-thick hot-rolled band was, unless otherwise noted, heat-treated for 5 min at 900°C before being cold-rolled to 25 mils. After a heat treatment of 1 to 3 min at 860°C, the strip was cold-rolled to 12 mils, the final thickness. The percent cube-on-edge texture was determined by dividing the maximum torque as averaged from four samples by the maximum torque of a 3-1/4 pct Si-Fe single crystal having the (110) plane in the plane of the sample. The torque measurements were made in a field of 1000 oe on 1-in.-diam disks. RESULTS AND DISCUSSION The importance of the thermal history of the ingot is evident in Fig. 1 from the appearance of strips heat-treated in a temperature gradient. The sample

Jan 1, 1964

By B. C. Mariacher

EXTRACTION of uranium from ores is being ac-complished by processes which. for the most part, subject the entire ore to acid or carbonate leaching. Ore deposits with a U 3 O 8 content below 0.10 pct U 3 O 8 are seldom considered suitable for treatment by leaching. A preliminary concentration that would enrich the uranium content of an ore by a simple, low cost process based on physical properties of the ore might result in some low grade deposits becoming commercial ores. In addition, the process might be employed in existing operations to reduce transportation and leaching costs and to increase capacity of existing leaching plants. A study to attempt the development of a preliminary concentration process for primary uranium ores was undertaken by the Colorado School of Mines Research Foundation under sponsorship of the U.S. Atomic Energy Commission. The objective of this work was to produce concentrates containing 0.25 pct U3O8 from the low grade ores tested. Ores Tested: The main effort was devoted to the low grade primary uranium ores from northwestern Saskatchewan. Samples were obtained from the Beaverlodge operation of the Eldorado Mining & Refining Ltd. Additional primary ores, obtained from deposits in Gilpin County, Colo., contained from 0.07 to 0.10 pct U3O8. Summary of Concentration Tests: The Beaverlodge ore was tested to determine amenability of the ore to concentration by magnetic, electrostatic, gravity, and scrubbing processes. None of these produced satisfactory results. Both gravity and magnetic processes produced fairly good concentrates when closely sized fractions of the ore were treated, but on the basis of treating the total ore, recovery was poor. Preparation of sized fractions and the low capacity of equipment for suitable concentration made these methods impractical. As flotation offered the advantage of treating the total ore without intermediate sizing, the main effort was in this direction. A flotation process was developed that fulfilled the concentration objectives as set by the AEC. Pilot plant testing was used to verify results obtained from laboratory batch testing. Mineralogy: A petrographic examination of the Beaverlodge ore included a study of polished sur- faces and identification of the radioactive mineral by autoradiograph and X-ray diffraction. Approximate quantitative mineral identification was as follows: quartz, 60 pct; orthoclase feldspar, 20 pct; chlorite, 10 pct; carbonates, 5 pct; and miscellaneous minerals, 5 pct. Included in this last group were plagioclase feldspar, pyrite, mica, chalcopyrite, pyroxene, sericite, magnetite, galena, and uraninite. The most general occurrence of uraninite was in the form of crusts and thin coatings on limonite-stained grains of pyrite, quartz, and pyrite-quartz intergrowth. At least 90 pct of the uraninite was still attached to other minerals in a 100 by 200-mesh size fraction. The uraninite crusts were as small as 10 to 20 µ diam, and 5 to 10 µ thick. The Flotation Process Petrographic examinations of the Beaverlodge ore had indicated the impracticability of attempting to concentrate the uranium by floating individual grains of uraninite. Liberation of the uraninite required grinding to sizes below those suitable for flotation. However, there was preferential association of the uraninite with some minerals while others were free of uraninite attachment. The approach to the development of a flotation process was, therefore, based upon an attempt to concentrate the uraninite by floating carrier minerals. The following paragraphs discuss the various stages of the process with regard to the factors tested and the conditions under which best results were obtained. Grinding: The most effective size range for flotation was —150 mesh + 13 µ. The —13 µ material in the final concentrate had a higher U3O8 content than the total ore, but not as high as the average concentrate; however, rejection of slimes before flotation was prohibitive because of the loss in uranium carried in the —13 µ fraction. Grinding techniques which contributed to a minimum production of fines, such as stage grinding, were then employed. Quartz and Silicate Depression: These minerals represented approximately 80 pct of the ore and were free to a large degree of uraninite attachment. Significant improvement in the grade of the concentrate was obtained by depression of these minerals with hydrofluoric acid or sodium fluoride. Promoter: Selective stage flotation of uraninite carrier minerals was simplified by development of a single promoter mixture. The mixture consisted of an emulsion of a fatty acid, fuel oil, and a petroleum sulfonate and was selected after a comprehensive series of tests. It contained three parts by weight of an oleic and linoleic acid such as Emersol 300,

Jan 1, 1957

By Josiah Royce

To evaluate chemically the sample of rock obtained by diamond drilling, it has long been recognized that the analyses of the two components of the sample, core and sludge, must be given appropriate influence in computing the average analysis of any unit of depth. The purpose of this investigation is to set forth what means are available for apportioning the effect of core and sludge on the final analysis, what variables affect the problem, and what combination of applied mathematics will closest approximate the truth under each condition as these variables proceed within their limitations. A drill hole is bored in iron ore exploration principally to test variations in rock composition with depth and is usually directed as nearly normal to the bedding of a horizon to be tested as possible. This practice has a tendency to minimize variation in composition laterally which in any event is not likely to be great. It is obvious that the opportunity for change in analysis of a particular rock is not statistically as great radially in a diamond drill hole where the distance in which such a change may occur is from 0.719 in. (EX bit) to 1.469 in. (NX bit) as there would be longitudinally even in a' run as short as 5 ft. Variations in composition of bedded or layered rocks are usually greater normal to the bedding than parallel thereto. Even in massive rocks, like porphyries, variations are functions of distance. Hence. in either case, variations along the hole are of greater effect than across it. Let us examine Fig 1 briefly to observe a cross section of a unit of depth of a typical diamond drill hole. If we neglect radial change in chemical composition, which we have seen is small compared to lengthwise variation, we can see that if core recovery was 100 pct, the core and its surrounding area, which would be recovered as cuttings (assuming 100 pct sludge recovery), must analyze the same if the sampling is perfect. This is the foundation of this paper, namely, that if core recovery is complete we may assume that the core constitutes as nearly as possible a perfect sample of the ground drilled. Now let us pass to the methods of weighting core and sludge in the final analysis and then develop each in turn. One might employ core analyses only, sludge analyses only, or apportion the influence of each by one of several methods. The most common apportionment is by direct proportion to relative theoretical vol- ' ume occupied by each component in the cylinder hollowed out by the drill, known as the Longyear formula. Another logical treatment would be to consider core and sludge in the final analysis according to the weight of each recovered. This procedure was elaborately set forth and refined by R. S. Moeh1man.l Then to be sure that we have embraced all the possibilities, we must admit that some other method or methods may be devised empirically or by mathematical maneuvers. Should a drill machine be capable of recovering 100 pct of the core in all types of rock, certainly core alone need be analyzed and no complicated mathematics are required; but although some companies have had fair success in obtaining high percentages of core in certain homogeneous ores on the Mar-quette Range, their same methods have proved disappointing on the Menominee, Cuyuna, and Gogebic Ranges where the iron formation often varies widely from flinty chert beds interstratified with soft hematite to wholly leached ore material composed of an unpredictable mixture of hematite and limonite with occasional zones of sugary, recrystallized chert. In spite of numerous mechanical improvements in core barrels, few drilling programs can count on complete core recovery. The sludge alone might be analyzed but for practical reasons this is inadvisable when core is obtained due to the numerous opportunities for contaminating or losing portions of the cuttings. The Longyear formula involves a weighting of the core and sludge in proportion to the theoretical volume of each, that is, where the volume of the core recovered is one-third of the total cubic volume of the cylindrical hole made by the drill, the analysis of the core is given one-third of the weight in the final analysis. This approach to

Jan 1, 1950

Jan 1, 1922

By Morris Muskat, James M. McDowell

A report is given of electrical analog experiments on the effect of casing perforation completions on well productivity for ideal uniform reservoirs under steady state homogeneous fluid flow conditions. Graphical results are presented for the effect of perforations of different densities and various degrees of penetration into the formation surrounding the casing or cement sheath. The latter range from perforations which terminate flush with the casing to those which extend into the formation a distance equal to the casing diameter. For the special case where the perforations terminate immediately beyond the casing with semi-spherical protrusions the electrical analog results correct and supersede previously reported theoretical calculations. It is found that the penetration of the perforations into the surrounding productive section may so increase the resultant productivity as to approach or even exceed that for open hole completions. INTRODUCTION A theoretical analysis of the effect of casing perforation on well completion, without additional penetration of the formation, was reported several years ago.' In this treatment the perforations were represented by mathematical sinks and no explicit account was taken of the imperviousness to flow of the casing in which the perforations were made. This procedure was justified by consideration of the mutual interference between the sinks, which seemed to indicate that the analytical method automatically eliminated flow across the casing radius between the perforations. However, both further theoretical investigation and the electrical analog measurements described below showed that this assumption in the previously developed theory was not valid and that the calculated well capacities would considerably exceed the correct values. § Even if this simplifying assumption were retained the generalization of the theory to situations where the perforations extend into the producing formation would be extremely difficult. On the other hand, the electrolytic model analog of this type of steady-state homogenous fluid system is, in principle, so simple that it has not been worthwhile to attempt to develop the exact analysis even for the more limited case of strict casing perforation. The whole problem has therefore been studied anew by electrical models to cover the range from holes in the casing which terminate flush with the casing surface to such as extend into the surrounding rock to a depth equal to the casing diameter. It is to be expected that the productivity of a well completed with casing radius* rw, perforated with holes of radius Tp, and extending to depths d into the surrounding rock, would depend primarily on the dimensionless geometrical parameters Te Tw TP d of the system, such as —, —, — , and —, where re is the Tw, a a rw external boundary radius and a is the mean vertical separation between the perforations. It will also depend, of course, on the number of perforation lines or total perforation density. While such parameters automatically control analytical treatments, it would require a very extensive series of model experiments to fully disclose their functional effect on the well productivity. For practical purposes, however, a rather limited range of the variables suffices to give the effects of interest. Accordingly, in the experimental study reported here the casing diameter has been kept fixed? at six in., the perforation diameter has been taken as either one-fourth in. or one-half in., their density has been varied from one to eight per ft, and their penetration into the formation has ranged from zero to six in., with a primary scaling factor of one to six. EXPERIMENTAL METHOD AND RESEARCH Although electrolytic model experiments have been made for years, there still seems to be some question as to what set of conditions will give the best results. For this reason a number of electrode materials and electrolytes were tried. Those chosen for the final experiments were copper electrodes and a weak copper sulphate solution as the electrolyte. This 'Assuming that the casing has been cemented with a uniform and impermeable cement sheath, the effective casing radius is to be interpreted as the external radius of the cement annulus. It is also assumed here that the casing is set through the complete producing section that it is perforated throughout with a uniform density and that tie formation has a a and isotropic permeability. As noted later, however, a uniform scale change permits reinterpreting the primary measurements to correspond to a casing diameter of 12 in.

Jan 1, 1950

By Richard G. Warren, Michael M. Minor, Gayle J. Thomas

INTRODUCTION Los Alamos Scientific Laboratory (LASL) initiated its effort in the Hydrogeochemical and Stream Sediment Reconnaissance (HSSR), a part of the Department of Energy (DOE) National Uranium Resource Evaluation (NURE) program, in late 1975. Since that time, LASL has completed sampling of the Rocky Mountain states of New Mexico, Colorado, Wyoming, and Montana at a density of about one water or waterborne sediment sample per 10 km2 and has sampled about 85% of Alaska at a density of at least one per 25 km2. Analytical results for these samples are reported by National Topographic Map Series (NTMS) quadrangle. All collection and analytical procedures have been standardized from the outset (Sharp, 1977; Sharp and Aamodt, 1978). Until early 1979, only uranium results were reported for these samples; thereafter, results include analyses for at least 42 additional elements in the sediment samples. Each LASL HSSR report also includes a discussion of the relationship of these analytical data to known or possible uranium resources; more recently, these data have been re- examined for their relationship to resources for other metals (Beyth et al., 1980; 1980a). Analytical results for LASL HSSR sediment samples are both comprehensive, including 43 elements, and precise, allowing close inter-comparison of data between quadrangles. A recent HSSR study shows that elemental concentrations in sediment samples from the Dixon Entrance quadrangle in Alaska are insensitive to the choice of sieve size fraction and do not vary significantly between stream locations a few meters apart, except for extremely high elemental concentrations (Warren, et al., 1980). Elements that are particularly reproducible include thorium, hafnium, and the .ram earth elements. Fortunately, sensitivities for these elements, which are often associated with uranium, are excellent by the nondestructive analytical technique of neutron activation analysis that LASL employs. Wet chemical techniques may not always give reliable results for these elements in sediment samples due to the difficulty of dissolving the resistate mineral phases that normally contain these elements. LASL has recently open-filed results for a large number of NTK3 quadrangles; to date analyses have been reported for about 605 of the quadrangles within the states of the Rocky Mountain region. As a result, uranium analyses am now complete for all sediment samples collected from the state of Wyoming. We have chosen to sumnarize the analytical results for Wyoming and portions of adjoining states hereafter termed "the ~ Wyoming regionn (Fig. 1 ) ; nearly 24 000 uranium analyses and nearly 17 000 analyses for 42 additional elements are available for sediment samples collected from this area. The DOE open-file report numbers are shown in Fig. 1 for reports open filed before September 1, 1980. The Wyoming region provides an ideal area for an examination of regional geochemical patterns ex- hibited by sediment samples. It is endowed with a variety of exposed geologic units and with widely distributed uranium districts associated with host units of several ages. However, discussion will focus on rock units of Eocene and Precambrian ages because they are widely exposed and host the majority of the uranium resources within the region (Fig. 2). Miocene units are also widespread and host mineralization in the Brown's Park Formation (Fig. 2). Epigenetic uranium mineralization occurs in sand- stones of lower Eocene age such as the Wasatch, Battle Springs, and Wind River Formations whereas vein type mineralization occurs in Precambrian crystalline rocks. Precambrian rocks within the region consist of a variety of granitic and meta- morphic rocks with l .4-2.8 billion year ages, except within the Uinta Arch, where they consist of a sequence of very low grade metamorphosed or unmetamorphosed 1.0 billion year old sedimentary rocks. Precambrian rocks have served as sources for much of the clastic material comprising the lower Eocene units, and may also have provided the source for the uranium in mineralized Eocene or Miocene sandstones (Stuckless, 1979). The remainder of this paper describes the relationship of elemental concentrations in HSSR sediment samples to exposures of Eocene and Precambrian rocks. The results are used primarily to determine where these Precambrian rocks might provide the most suitable uranium source areas and to infer the direction of transport toward adjacent depositional basins during the Eocene.

Jan 1, 1980

By T. A. Read, M. S. Wechsler, D. S. Lieberman

A theoretical analysis of the austenite-martensite transformation is presented which predicts the habit plane, orientation relationships, and macroscopic distortions from a knowledge only of the crystal structures of the initial and final phases. THIS paper presents a new theory of the formation of martensite. This theory makes possible the calculation of the austenite planes on which the martensite plates form, the orientation relationship between the austenite and martensite crystal axes, and the macroscopic distortions which are observed. The only input data needed are the crystal structures and lattice parameters of the austenite and martensite. Considerable effort has been devoted over the past thirty years to the development of an understanding of the crystallographic features of martensite reactions. Much of this work has been done on steels and iron-nickel alloys, for which a great deal of data has been accumulated concerning the shape and orientation of the martensite plates, the relative orientations of the austenite and martensite crystal axes, and the observable distortions which result from transformation. These observations are reviewed in refs. 1, 2, and 3. The first major step toward an understanding of these phenomena was made in 1924 by Bain,' who showed that the a body-centered cubic structure can be produced from the 7 face-centered cubic structure by a contraction of about 17 pct in the direction of one of the austenite cube axes and an expansion of 12 pct in all directions perpendicular to it. Since that time, most of the efforts at further interpretation have been made by investigators who have worked from the phenomenological data, incorporating some of the information from the lattice properties, and have sought an analysis into likely deformations which would produce the observed results."- "11 but the three most recent papers on the subject have already been reviewed in some detail." Machlin and Cohenl0 measured the components of the distortion matrix and verified that the habit plane is a plane of zero distortion and rotation for the (259) case. They showed that the measured distortion matrix, when applied to the parent lattice, does not yield the product lattice and hence some inhomogeneous distortion must occur. Frank,u working from the lattice properties and taking some clues from the observations, considered the correspondence of close-packed rows and planes in the austenite and martensite. He predicted substantially the observed lattice relationship and habit plane for certain steels which have a (225) habit. Geisler12 suggested that there is a natural tendency for the habit plane to be a (111) and postulated certain slip processes to account for the fact that the experimentally observed habit plane is irrational and deviates from the assumed one. The present work differs from previous treatments of martensite formation in that it permits calculation of all the major manifestations of the process. Habit plane indices, orientation relationships, and observable distortions are all calculated from a knowledge of the crystal structures of the initial and final phases alone. The calculations contain no adjustable parameters. The agreement found between calculated results and the observations reported in the literature constitutes powerful evidence in favor of the mechanism of martensite formation proposed. The theory is applicable to systems other than steel (as is discussed later in this paper) which exhibit a diffusionless phase change but because of the wide-spread interest in the austenite-martensite transformation, particular attention will be given to the iron-base alloys. For other systems which undergo a similar face-centered cubic to face-centered tetragonal transformation, the mathematical treatment is identical with that presented here. Hence the theory successfully describes the transformation in the indium-thallium alloy.'" Homogeneous Transformation to Martensite The distortion which any homogeneously transforming volume of austenite undergoes in order to become martensite is shown in Fig. 1, as was first suggested by Bain.' (This distortion will hereafter be referred to as the "Bain distortion.") This specification of a contraction along one cube axis ;ombined with an expansion in all directions perpendicular to this axis describes what is properly called the "pure" distortion associated with this transformation. The distinction between a "pure" and an "impure" distortion plays an important part in the discussion which follows. A "pure" distortion is characterized by the existence of at least one set of orthogonal axes fixed in the body which are not rotated by the distortion. (These are called the "principal axes" of the distortion.) No such set of axes exists in the case of an "impure" distortion. On the other hand, an impure distortion can always be represented as the result of a pure distortion combined with the rotation of the specimen as a rigid body. For a given impure distortion the corresponding pure distortion

Jan 1, 1954

By A. H. Heim

A method and apparatus for measuring gas porosities of rocks are described. The apparatus can be assembled from commercially available components. In principle, measurements are made by volume substitution at constant pressure. The maximum error is not more than 0.3 porosity per cent. Typical results are given. INTRODUCTION Determining the porosity of rock samples is one of the most important and yet most varied types of measurement in core analysis. Among the many techniques devised are the so-called "gas porosity" methods. An old and well known example is the Washburn-Bunting method.' The U. S. Bureau of Mines2-' described and later improved the apparatus for a now widely used method generally known as the "Boyle's law" method. In the present form of the Washburn-Bunting method,' the volume of air in the pores of a rock sample at atmospheric pressure is extracted and then collected in a graduated burette at atmospheric pressure. The volume of air is read directly as the pore volume of the sample. The absolute error in reading the collected volume of gas is independent of the total volume; thus, the relative error is larger when the volume is small, as it is for rocks of low porosity. In addition, the sample after measurement contains mercury, which limits its use for other analyses. The Bureau of Mines (or Boyle's law) method measures directly the solids volume of a sample from which the pore volume and porosity are derived, using a separate measurement of the bulk volume. Gas at a few atmospheres pressure is introduced into a sample chamber of known volume containing the rock sample. The pressure is accurately measured. Following, the gas is expanded into a burette at 1 atm, and the gas volume is read directly. From the initial pressure p, and the final pressure p2 and volume v,, the initial gas volume v1 is calculated using Boyle's law; that is, p1v1 = p2v2. Volume v, minus the volume of the empty sample chamber is the solids volume of the sample. The accuracy of the method is limited, unless corrections are made, by deviations of the gas from the "ideal" gas-law behavior assumed in the simple form of Boyle's law. The purpose of the present paper is to describe a method for measuring the gas porosity of a rock which avoids many of these difficulties. Gas volumes are measured directly with the same accuracy as the bulk volumes. Pressures of at least an order of magnitude larger than those of previous methods are employed to insure rapid penetration of the gas into the sample. While special equipment may be built to apply the method, the porosimeter may be constructed as well from commercially available components. For simplicity, the apparatus described will be referred to as the "Constant-Pressure gas porosimeter". THE CONSTANT-PRESSURE METHOD Fig. 1 shows schematically the arrangement of components comprising the present Constant-Pressure porosimeter. Briefly, the method is one of volume substitution and may be considered a null measurement. Omitting (for the present) some of the operational details, the method of measurement consists of the following three steps. 1. After evacuation, the volume of the measuring system (a ballast chamber, a manifold, two gauges and their connections) up to the sample chamber is filled with gas to a high pressure (- 1,000 psi). A sample of the gas at this pressure is trapped in one side of a sensitive differential pressure gauge to serve as the reference pressure for subsequent steps. 2. The evacuated sample chamber containing the rock sample is opened to the measuring system. As the gas expands into the chamber, the resulting decrease in pressure unbalances the differential pressure gauge. 3. The pressure is restored by means of a mercury volumetric pump. The volume of mercury injected exactly equals the free or void volume of the sample chamber (volume of empty chamber minus the solids volume of the rock within). From the injected volume and the known empty chamber volume, the solids volume is obtained and the porosity calculated. The pressure and the volume occupied by the gas are the same before and after opening the sample chamber. Expansion and compression of the gas are incidental operations and do not enter into the calculation of porosity. By the pressure balancing or nulling, the free volume of the sample chamber is merely substituted by an equal and measured volume of mercury. Since the measurements are at constant pressure, there are no compressibility corrections necessary for the sample chamber.

By V. F. Hollister

The Queen Charlotte gold deposit (also known as the Specogna, Babe, or Cinola) was discovered in late 1970 by Efrem Specogna and Johnny Trico. They were prospecting along the trace of the Sandspit fault, and they sampled jarositic material that included veins from the fault zone. Their assays included some good gold values. They located the Babe Claims in 1971 and optioned them to Kennco Explorations Ltd. Kennco conducted stream sediment and soil geochem studies, geological mapping and drilling of 55.2 m (181 ft) in two drill holes. Kennco withdrew from the property, and by 1977, Cominco, Placer Development, Silver Standard, and Quintana Minerals had each successively worked on the deposit. Consolidated Cinola Mines bought the claims in 1977 and completed exploration of the deposit ultimately in a joint venture arrangement with Energy Reserves. Energy Reserves entered in late 1979, and by 1983, a total of 200 surface and 12 underground drill holes had been completed, totaling 28 600 m (93,832 ft). In addition, a 461.9 m (1515 ft) adit was driven in the ore body. Reserves published by Cinola aggregate 34 Mt (37 million st) of 1.7 g (0.060 oz) Au per tonne. All industry geologists working in the area agree that the Queen Charlotte gold is an epithermal gold deposit in porous volcaniclastic and clastic rocks that is genetically related to a Miocene-Pliocene rhyolite plug. The geologic description here follows the oral presentation made by G. G. Richards, J. S. Christie, and M. R. Wolfhard at a 1976 CIM meeting. Additional comments by the late C. S. Ney of Kennco Explorations are included with the Richards, Christie, and Wolfhard data to complete the geologic set- ting. The attached reprint by Champigny and Sinclair (1 980) provides additional data on the deposit. The Queen Charlotte (Babe, Specogna, or Cinola) gold deposit is located on Graham Island in the northern Charlotte Islands, at the fault boundary of the Skidegate plateau and the Charlotte lowlands. The Sandspit fault marks the physiographic boundary, and it is intruded by rhyolite porphyry at the deposit. Because displaced geochem anomalies, drain- age patterns, and topography suggest dextral and east side down movement for the fault, exposed east block rocks are younger than rocks west of the fault. The east block, which included the ore deposit, is a lowland largely masked by unconsolidated Pleistocene and Recent clastic rocks. Rocks west of the rhyolite plug, on the Skidegate plateau, are Cretaceous carbonaceous and calcareous shale unconformably overlain by a thin veneer of rhyolite tuff. The deposit is about 100 m (328 ft) above sea level. GEOLOGIC SETTING At the ore deposit, the Sandspit fault is a complex structure. However, lithologies on either side of the fault-controlled rhyolite porphyry plug are distinct. West of the rhyolite, the upper member of the Cretaceous Haida formation shale is the most common rock type. The member is composed of dark grey to black, poorly consolidated, and thinly bedded carbonaceous and calcareous shale. The sequence is silicified to an argillite or a hornfels near the rhyolite. West of the rhyolite porphyry plug, but not importantly involved in the mineralization, is a thin masking cover of rhyolite tuff. The tuff unconformably succeeds the cretaceous shale, but it is largely eroded in the mine area. East of the fault-controlled rhyolite porphyry plug is a thick section of conglomerate and sandstone of the Miocene- Pliocene Skonun formation. The ore body occurs within the coarse clastics, the rhyolite intrusive as the western boundary. Ore is entirely contained within the clastics. Original permeability of the clastic rocks was a major control for ore deposition and alteration, and for that reason, the Skonun formation is described in greater detail. The Skonun formation clastics unconformably overlie Haida shale. The Skonun is at least 300 m (984 ft) thick in the mine area, where it trends northerly and dips easterly 15º to 25º. The sequence is about 62 percent conglomerate, 3 1 percent coarse arkosic sandstone, and 7 percent interbedded siltstone and sandstone. Contacts between adjacent beds are generally sharp. Stratigraphic correlations between drill

Jan 1, 1985

By Lloyd Pollish, Robert N. Breckenridge

SUCCESS in any underground mining operation is determined by accessibility of the orebody, which in turn is dependent upon maintenance of passageways to the mining zones and temporary support of the voids caused by extraction of ore. This is accomplished by one or a combination of the following methods: timbering, back-filling, pillaring, or, more recently, rock bolting. Timbering has usually been the principal means of maintaining these underground openings necessary for mining operations. Timber, however, does not prevent ground movement beyond the scope of localized sloughing, which is indicated by the gradual failing of the timber itself. Besides this, timbering has always been a costly process, and with the decline of available supplies of timber close to the mining areas, mining men have constantly sought other methods of controlling ground. Rock bolting is now replacing timbering at an ever increasing rate. Experience has proved that this form of ground support is just as applicable to blocky igneous rock as to stratified rock. Besides preventing sloughing of the walls and back of underground openings, Fig. 1, rock bolting has a stabilizing effect on the surrounding ground in much the same manner that steel reinforcing rods add to the strength of concrete structures. Further, rock bolting is flexible and may be applied to any shaped excavation, whereas timber sets are in a fixed pattern and the ground must often be changed to conform with this pattern. Rock-bolting installations were made in metal mines of the Northwest as early as 1939. An exhaust air crosscut was driven that year in one of the Butte mines of the Anaconda Copper Mining Co. The crosscut was rock-bolted and gunited at the time it was driven and is still being used to exhaust hot humid air from the 3400 level of the Belmont mine. It is interesting to note that no sloughing or caving has taken place in the 14 years it has been open. Even though these early installations of rock bolts were successful, few men recognized their potentiality until recent years, when the coal mines started their programs of mechanization and the great trend toward roof bolting began. In some areas of the Northwest stopes that previously required heavy timbering and close backfilling are now being mined by the more economical cut-and-fill and shrinkage methods. When used in conjunction with timbering, rock bolting increases the efficiency of the operation by decreasing hanging wall dilution and by making it possible to blast larger rounds. Most of the rock bolts installed to date in mines of the Northwest have been the 1-in. diam slot and wedge type, but there has been a recent trend to- ward using the 3/4-in. diam expansion shell bolt shown in Fig. 2. In addition to these commercially manufactured steel bolts, wooden bolts have been used with considerable success by the Day Mines of Wall'ace, Idaho. Installation of the slot and wedge type requires three distinct operations, with tools for each operation: 1—drilling the hole to proper diameter and depth, 2—setting the bolt, and 3—tightening the nut. Holes are drilled and bolts set with pneumatic rock drills. A number of setting or driving tools have been used successfully, but most follow the same general pattern. Usually the driving tool is designed to accommodate a short length of drill steel on one end and the rock bolt on the other end. In this manner the hammering effect of the rock drill is transmitted through the steel and driving tool to the bolt. When machines not having stop rotation are used, slippage is allowed between the driving tool and bolt or between the drill steel and driving tool. The rock bolt nuts are tightened either with pneumatic impact wrenches or with hand wrenches. Impact wrenches are desirable because they are faster and assure adequate tightness. Expansion shell bolts have the following advantages over slot and wedge rock bolts: 1—No special equipment other than a wrench is needed for their installation. 2—Installation is faster. 3—They are removable. 4—Holes need not be drilled to a specific depth as the expansion shell will anchor anywhere along the length of the hole. These advantages are offset somewhat by the lesser strength of the bolt, since expansion shell bolts are generally made from 3/4-in. diam steel as compared to 1-in. diam steel for the slot and wedge type. One manufacturer, however, is now fabricating expansion shell rock bolts from steel of high tensile strength, which gives this ¾-in. bolt a much greater strength than that of the mild steel bolt. Table I illustrates tests made by the Anaconda Copper Mining Co. to determine the proper hole size to use with various types of bolts and to determine

Jan 1, 1955

By M. Safiuddin

Within the mining industry, open-pit mining has progressed to a point where a 200-yard walking dragline is as conceivable today as a 35-yard dragline was just a few years ago. This is possible due to the technological advances and efforts of the excavator manufacturers, and the manufacturers of electrical equipment have always stayed abreast with them in meeting their requirements and in making available their experience with the latest control techniques and hardware from various fields for application in the mining industry. An electrician in the coal mines of Pennsylvania who had not heard the word "thyristor" a few years ago now wonders how the old excavators with Rototrols® and magamps could ever work. The thyristors, transistors and operational amplifiers which were considered too fragile and delicate for a rugged and severe application like the mining industry, today constitute the brain of an excavator control taking commands from the operator and giving signals to the muscles of the excavator to move the bucket within a few seconds. A giant 200-yd bucket filled with overburden moves within seconds of the operator's command. Digging cycles for these excavators range from 40 to 60 sec depending on the swing angle. With these tremendous production capabilities of the excavators, the equipment failures and downtime become very expensive, and the loss of return on large capital investment for such machines becomes intolerable. Even though these failures and downtimes cannot be avoided completely, a good preventive maintenance program can help reduce them, thus increasing the machine availability. As we shall see below, the causes for breakdowns and failures of electrical equipment can be analyzed and a good preventive maintenance program can be drawn up to eliminate most of these failures.

Jan 9, 1967

By A. C. D. Chaklader, Ashok K. Kakar

The basic density equation originally dericed ' to predict the increase in density of a compact of spherical particles with the progressive deformation at the points of contact has been further modified to include the yield strength of the material. This has been done by assuming that the contact areas grow to stable sizes under a fixed stress which is equal to three times the yield strength. The final equation has the form: where Do and D me the initial and final bulk densities of the compact, u is the applied pressure, and Y is the yield strength of the material. This equation was tested with the data obtained on spheres of lead, K-Monel, and sapphire. The calculated yield strength t~alues for lead and sapphire are within the range of values reported in the literature. A few of the earliest hot pressing models proposed to explain the mechanism by Murray, Livey, and williams2 and then by McClelland3 are based on a plastic flow mechanism. However, more recent investigations suggest that the overall densification process is a combination of several mechanisms, such as particle rearrangement, fragmentation, plastic flow, and stress-enhanced diffusional creep. While fragmentation and particle rearrangement are considered to be responsible for the densification in the early stages,"475 it has been concluded that the final stages of hot pressing are controlled by stress-enhanced diffusional creep.516 The manner in which the densification takes place, i.e., by fragmentation, particle rearrangement, plastic flow, or stress-enhanced diffusional creep, would depend upon the type of material, the temperature, and the stress level used during the hot-pressing experiments. Metal compacts can be expected to have a much greater contribution from plastic flow than ceramic oxides. Also, plastic flow would be a significant contributing factor to densification at high temperatures and high stresses. Most of these works, directed towards elucidation of densification mechanism, have dealt with kinetics of the process. The results of most of the authors vary from one another and they have proposed either new empirical or semiempirical equations to fit their data. The densification rate was found to vary with the type of the powder, shape and size of the powder, initial packing density of the compact, and a few other factors such as rate of heating, pressure, and so forth. Beyond the initial stages, the densification process has been considered to be as time-dependent flow, controlled by a diffusional process, e.g., Nabarro-Herring creep. Palm our, Bradley, and johnson' have attempted to use modified creep rate equations to interpret the data of densification under hot-pressing conditions. Beyond the initial stages, however, the densification would be controlled by a process depending upon the temperature, pressure, and size of the powders. It is the authors' belief that such densification cannot be exclusively controlled by a single process and so attempts should be made to study some observable phenomenon like microstructure, yield strength, and so forth. The emphasis of this work has been toward studying the densification problem from a more fundamental point of view. Some of the principal variables, like initial packing density, mode of packing, and size of the powders, have been controlled to a great extent. The total strain produced on pressure application (instantaneous) in such a case can be considered to be due to plastic and elastic deformation. The elastic component of the strain can be determined by decreasing the load to the initial value. The strain remaining then can be correlated with the contact areas produced by deformation and the corresponding applied load. In a previous paper,' the possible deformation behavior of spheres in a compact has been theoretically analyzed and experimentally tested. The change in contact area radius a relative to the particle radius R was related to the bulk density and the bulk strain for simple and systematic modes of packing. Tt was found that a density equation relating the above parameters can be represented by: where D and Do are the bulk densities of the compact at any value of a/R and a/R = 0, respectively. This basic equation should hold for any material as it was derived from geometrical considerations alone. An attempt has been made in this work to include the yield strength in the above density equation, so that a knowledge of the properties of any material can be used in predicting the densification behavior during the hot-pressing process. THEORETICAL CONSIDERATTONS The deformation of two spheres in contact under a static load can be compared to the deformation occurring between a hard spherical indentor and the flat face of a softer metal. Tt has been shown theoretically by both ~encky~ and lshlinskyg and experimentally by ~abor" that, for a material incapable of appreciable work hardening, the mean pressure required to produce plastic yielding (for deformation occurring between flat face and a hemispherical indentor) is approximately equal to three times the elastic limit, Y, of the material (in tension or compression experiments). Tabor has further observed that the same relationship is valid in the case of work-hardening materials, if the elastic limit at the edge of the indenta-

Jan 1, 1969

By A. Simkovich, R. W. Lindsay

The possibility of using sodium sulfide slags to remove copper from ferrous alloys has been investigated by Jordan1 and by Langenberg.2, 3 In these studies, such slags were determined to be capable of removing copper and sulfur from the melt. The present work represents additional effort to clarify the effects of temperature on copper removal. The experiments were performed in a 17-lb induction furnace. Graphite crucibles contained the melts and kept the baths saturated with carbon. Temperatures were measured with a calibrated optical pyrometer and were controlled by manipulation of power input to the furnace. Estimated accuracy of temperatures in this investigation is ± 10°C (18°F) for measurements prior to slag additions, and + 20°C (36°F) after slag formation. The procedure consisted of melting 800 g of electrolytic iron. During this step, powdered graphite covered the exposed iron surface. After a predetermined temperature was reached, copper shot was added. A sample of the molten alloy for chemical analysis was then aspirated into a silica sheath. Next, a slag-forming mixture of sodium sulfite and graphite was added instantaneously to the melt. The sodium sulfite amounted to one-tenth the charge weight of iron; sufficient graphite was added to combine with oxygen in the sodium sulfite, assuming formation of carbon monoxide and reduction of the sulfite to sulfide. Subsequent to the slag addition, the molten alloy was sampled periodically, with the exception of heat A in which no intervening samples were taken between the slag addition and the end of the run. The iron was poured into a graphite mold, and the ingots sectioned and drilled for samples. Results of selected heats are presented in Table I. Analyses of samples drawn from the iron prior to slag addition are listed under zero time. Two samples from heat D were reported with copper contents greater than the initial concentration in the bath. Owing to the gradual but complete disappearance of slag during this heat, it is believed copper momentarily became more concentrated in the upper portion of the bath while reverting from the slag. This is the region from which samples were drawn. It should be noted that analysis of the ingot was equal to the copper content at the time of slag addition. The terminal temperatures of heats D and E, and the initial sulfur content of heat A are also to be noted. Because of the large temperature drop which occurred when slag was formed in heat D, power input to the furnace was increased in heat E after the slag addition, causing a higher terminal temperature. In heat A, the initial sulfur concentration was relatively high as compared to heats B through E owing to contamination by some slag remaining in the crucible from a previous heat. It is evident from Table I that copper was removed at the onset of slag formation. Roughly 30 pct of the copper was taken into the slag, with the exception of heat D, which had approximately 50 pct removed. For a comparatively short time of slag-metal contact, it appears that no gain is to be made in copper removal through use of high or low temperatures. If the slag initially formed remains in contact with the iron for an extended period, temperature has a marked effect upon copper removal, as can be seen by studying results for the two extremes in temperature. At about 1425°C, the copper level remained relatively constant after the initial removal by the slag. However, in the region of 1670°C, a definite reversion of copper occurred. Reversion was incomplete in heat D, and complete in heat E. The final temperatures of heats D and E differed by about 75°C. This temperature difference is thought to be the reason for only partial copper reversion in heat D. It is believed the effects of temperature noted above are related to the evolution of a white fume, which appeared in every run except heat A. (In the case of heat A, the fume was practically indiscernible.) After each slag addition, a yellow flame formed for about 5 sec. When the flame subsided, a white fume appeared. Upon contact with surrounding cooler surfaces, this fume deposited as a white solid. In the experiments made at 1425°C, evolution of fume continued unchanged to the end of the runs. However, heats D and E exhibited a different behavior. A very noticeable decrease in fume evolution from heat D was observed. Furthermore, this heat had much less slag remaining than did runs A through C when the experiments were terminated. No slag remained at the end of heat E; evolution of fume from this heat ceased prior to pouring. Spec-trographic analysis of the white deposit indicated sodium to be the major metallic element, with the maximum concentration of iron and copper as 0.1 and 0.01 pct, respectively. It is supposed the white fume observed in these experiments is principally sodium oxide (Na2O), formed by oxidation of sodium in the slag and subsequent sublimation. (Sodium oxide is a white to gray substance in the solid state; at 1275oC, it sublimes.4) According to this mechanism, elevated temperatures would accelerate removal of sodium from the slag, sulfur pickup by the

Jan 1, 1961

By P. J. Shenon

ENROLLMENT in geological and mining engineering curricula is declining at an accelerated rate despite the greatest need for trained men ever extant in the minerals industry. Industrial and military demand is mounting, but the number of freshmen selecting the mineral field continues to fall. Estimates on the needs of industry range as high as 30,000 new engineers a year. The current deficit is more than 60,000 engineers less than the 350,000 to 450,000 which eventually will be needed. The indisputable fact is that the colleges are turning out fewer and fewer engineers despite the greatest enrollment in colleges and universities ever experienced in the United States. In 1950 a record 52,000 young men stepped out of the confines of ivy covered walls with engineering degrees in their hands. By 1951, however, the number dropped to 41,000 and present enrollment indicates a national graduating class of only 25,000 for 1952. No letup in the drop is forecast. About 19,000 can be looked for in 1953 and 1954 may reach an unhappy 12,000. It becomes clear that something must be done to attract high school graduates to engineering. One immediate possibility could be to make the course burden carried by the engineering student somewhat lighter. The prescribed curriculum in many schools is such that the student takes the path of least resistance, and instead of training for an engineering future, studies for a vocation which will allow him to learn and at the same time get at least a nominal enjoyment out of college life. Review geological and mining curricula of 20 colleges and it will be found that the engineering student is a veritable pack mule compared to a lad taking liberal arts or some other non-technical program of study. The curriculum for geological engineering at one school calls for 202 semester hr, with almost 23 hr carried per semester. Multiply this figure by three hr, the minimum supposedly to be devoted to a credit and you get 69 hr per week. With a bare minimum of 84 hr for sleeping and eating, about two hours a day remain for recreation. However, the load of other schools investigated is about 19 hr. The University of Utah requires 238 quarter hr for graduation with a degree in geological engineering, while requiring only 183 quarter hr for baccalaureate degree from University college, Utah's liberal arts school. It can be stated with a measure of surety that the same proportions exist in other universities. The first step would be for ECPD to review its requirements for mining and geological engineering. It must recognize that mining and geological engineers operate in a specialized field, as do other types of engineers. Although a geological engineer may not design a bridge, as pictured by the ECPD Committee on Engineering Schools, his field of design calls for similar engineering precision, a knowledge of materials, construction methods, economic considerations, and financing. Six schools have been accredited by the ECPD. What is the basis for approval and can the requirements be modified and still be kept in line with the needs of the geological engineer? Course work from school to school varies with the exception of mathematics, chemistry, and physics. Even in those courses the not inconsiderable variation lends dubious creditability to the mean. One accredited school requires 7 1/3 semester hr of chemistry, compared with 24 hr required by another, making an average for the six schools of 17 1 /3 hr. Required credit hr in mechanics ranges from 4 to 18 and in surveying from 2 to 15. Several non-accredited schools require more hr than do the accredited schools in some courses. Why is the engineering student forced to carry such a back-breaking load? The answer is of course fairly obvious. He is irrevocably set apart from the rest of the student body because of the nature of his life's work. He is training for a place in a world where technology is becoming increasingly involved. He must be prepared to do a job now-and not later. Mining and geological engineering require the same essential backgrounds as other engineers, and more. The "more" is a knowledge of mining methods, metallurgy and geology for the mining engineer. The geological engineer must know in addition, mineralogy, petrography, and geophysics. The load is compounded finally by the addition of liberal arts courses. Should anything be done to relieve the situation? Today's engineer must be a whole man, capable of handling the tools of communication and with an understanding of the economics of industry. He must be able to write clear simple English, and he must be man who can think from some other position than bent over a work table. He must be aware of the history of his country and to some extent that of the world. Not all schools share this view. Only two of the accredited schools require history courses. However, five of the non-accredited schools make it mandatory. Four accredited and five of the nonaccredited schools require economics. Courses in mathematics, physics, and chemistry are fundamental in engineer training. The average for the accredited schools could serve as a guide in

Jan 1, 1952

By Rossiter TV. RAYMOND, Charles H. Snow, THEODORE DWIGHT

SECRETARY'S NOTE.-The complete list of all officers of the Institute will be found on p. iv. of this number of the Bulletin. The following explanation may recall to old members, and convey to new ones, the relations of the two governing bodies, as determined by the, Certificate of Incorporation of the Institute, and the Constitution and By-Laws adopted in accordance therewith. The body legally responsible for the business management is the Board of nine Directors (three elected annually to serve three years), which elects its own officers. This body, for reasons of practical convenience, is composed of well-known members, residing in New York City, and able to attend, without serious inconvenience or expense, the necessary meetings of the Board. The officers of this Board are legally the officers of the Institute. But, apart from business manage-ment, the Board exercises no control over the election of members, or the professional and technical work of the Institute, except that its vote is required to elect honorary members, upon the recommendation of the Council. The Council is a. body, constituted in all respects (except that it has no Treasurer) like the Council existing before the incorporation of the Institute, in January, 1905, and charged with all duties and powers, except those which the Board of Directors must legally perform. It elects members, appoints the times and places of professional meetings, and controls the publication and distribution of papers and volumes, etc. Its members (President, Vice-Presidents and Councilors) are elected by the members of the Institute, voting in person or by proxy, and after publication of the nominations received ; and it is intended to repre¬sent, as far as practicable, both the professional and the geographical distribution of the membership. Consequently, whatever professional honor attaches to official position belongs to membership in the Council, rather than in the legal Board of Directors. This remark implies no disparagement of the members of the latter body, every one of whom has served, or is now serving, as a member of the Council. But it is only fair to explain that their election and continued re-election as Directors is simply a matter of legal convenience.

Mar 1, 1906

By Edgar Rickard

E UGAR RICKARD comes of a long line of mining men and was born at Pontgibaud, France, in 1874, where his father was then in the course of his professional work. Later his father came to California and was until his death prominently connected with milling in that state and Nevada. Edgar Rickard grew up at Berkeley, attended the University of California, graduated in 1895 from the mechanical engineering course, and remained a year longer for post-graduate work in the College of Mining. His first job was as assarer for the Mountain Copper Co., Keswick, Cal., in 1896. The following year he was assayer and surveyor for the Cornucopia Mines, Oregon. In 1898, he joined the staff of the Venture Corporation, London, and for two years made examinations for them in various parts of the world. He served as mine manager at Cripple Creek and at the Briseis tin mine, in Tasmania. From 1901 to 1905, he was general manager of the Progress Mining Co. in Lower California, but when his cousin, T. A. Rickard, bought the Mining and Scientific Press he was persuaded to come to San Francisco as business manager of that periodical. A few years later the two cousins went to London and started the Mining Magewine there as a joint venture, Edgar being the business manager. In 1915, he took over control, T. A. Rickard returning to California to devote his time to the Mining u.rbd Scientific Press. In 1917 Edgar Rickard sold out to his British associates and came home to serve in the Food Administration through the war. Rickard was one of the first of the American engineers called to his staff when Herbert Hoover began his relief work by helping stranded Americans home at the be- ginning of the war and he has been with him constantly since in the Commission for Relief in Belgium, the

Jan 1, 1929

By Edwin Ludlow

EDWIN LUDLOW, president of the American Institute of Mining and Metallurgical Engineers for the year beginning Feb. 15, 1921, is a well-known figure in the state that was the birthplace of the Institute-Pennsylvania-although he was born and educated in New York and is again one of its residents, after years of active work in the field. Mr. Ludlow was born at Oakdale, Long Island, and was graduated from the School of Mines at Columbia University with the class of 1879. After graduation, he became a civilian worker with the U. S. Engineer Corps under General William Ludlow, his brother, and for two years did river and harbor surveying along the New Jersey coast.

Jan 1, 1921

By E. A. Holbrook

AS A whole, engineering schools have not awakened A to the fact that the workmen compensation laws passed in most of our states between 1914 and 1917 effected a quiet but none the less real revolution in. the relations between labor and management; no longer are industrial accidents unfortunate or careless happenings over which we feel a humanitarian interest and sorrow, they are a cost of the process and the finished product, as vital as improved design and increased efficiency. Last year the writer and others made a committee report to. the American Institute of Mining and Metallurgical Engineers on the cost of accidents in the coal industry of Pennsylvania. Comparatively the accident record in Pennsylvania coal industry is not high, yet the direct compensation cost plus the interference with operation cost of accidents was over 5 per cent. of the total cost of producing the coal. This stands out more vividly -if you realize that about 70 per cent. of the' cost of producing the coal is for payment of labor, wages that are fixed and over which engineering efficiency and management skill have little or no direct effect. This leaves 30 per cent. of the cost chargeable .to hoisting, haulage, overhead 'and other items subject to engineering control. One sixth of this is due to cost of accidents. Surely a direct place 'for an engineering attack.

Jan 1, 1925

By J. E. Johnson

Discussion of the paper of Mark A. Amnion, presented at the Cleveland meeting October, 1913, and printed in Bulletin No. 70, October, 1913, pp. 1167 to 1 79. J. E. JOHNSON, JR., Ashland, Wis.:-Mr. Amnion's paper is of great value and it is not with any desire to reflect. on it that I wish to make some comments on the use of the scleroscope. We obtained one on trial some months ago and made very extensive tests with it, but without getting very satisfactory results. The readings on good car-wheels and bad ones were just about the same, but the factor in its use most likely to produce erroneous results is a variation in the thickness of the specimen being tested. In order to find out something on this subject we cut a thin disk, about -1,: in. thick, off a brass rod; then one 0.25 in. thick, and another about 1 in. thick, put the surfaces of all in about the same condition and tested them with the scleroscope. The readings varied widely; the resilience of the anvil evidently entered to a very high degree on thin pieces. By putting a soft cushion between such a thin specimen and the anvil, and forcing it up against the tube, the softness of the cushion cut off the resilience of the anvil and the results were more like those of the thick specimens. After a thickness of 1 in. was passed, the specimen seemed to have mass enough so that the resilience of the anvil no longer played an important part, and above that thickness results on different materials would be comparable, even though the thicknesses differed. But in order to get comparable results on thin specimens the thickness of those being tested should be the same. I should like to ask how the variations introduced in this way were overcome, so as to get strictly comparable results. Mr. AMMON :-.I have not had much experience in that, but the scleroscope is simply an indication of the surface harden-

Dec 1, 1912