Search Documents

By P. de Vitry, Willis P. Mould

THE wire saw is a tool not less than 60 years old, probably nearer 100 years old. It was developed in Europe and is reputed to have originated in Belgium. Frombold is said to be the original patentee. [ ] Wire sawing equipment, as indicated in Fig. I, is very simple. It consists of a three-strand wire cable, usually 3/16 or 1/4 in. in diameter, or a single flat ribbon of medium hard, tough, alloy steel twisted into a helix of those diameters, made to form an endless belt of any length up to several thousand feet. The wire is guided into the cut by sheaves mounted in slides on steel columns situated close to either end of the cut. The feed motion usually is controlled either by gravity or by hand-operated feed screws. The steel columns or "standards" range from 15 to 30 ft. in length. At the top is a swiveled arm supporting a sheave similar to the traveling sheave below. Immediately under the swivel-mounted sheave is a guy plate or collar with shackles attaching four chain or wire-rope guys with suitable tightening devices, or with two guys and two jack legs for supporting the standard vertically or at any desired angle. The usual drive is by a 10-hp. motor through a gear reducer, on which are mounted two grooved sheaves, one of which is keyed and the other free running on the shaft. Tension is provided by a car running on a track in line with the driving sheave

Jan 1, 1946

By P. Stark, B. S. Lement

ACCORDING to Hanemann1 the hardness of retained austenite in a 1.7 pct C steel is increased by subsequent tempering. He reported that the hardness of this constituent increases only slightly on tempering to 300°F, rises more rapidly above this temperature, and attains the same value as the tempered martensite present in steel at approximately 480°F. The variation of hardness of both retained austenite and martensite with tempering temperature as obtained by Hanemann1 is shown in Fig. 1. Hanemann attributes the increase in hardness of the retained austenite essentially to continued formation of fine needles of martensite on tempering. Although he did not explain the actual mechanism involved, work hardening of retained austenite by the plastic deformation associated with such martensite formation appeared to be a possibility. Recently Lement, Averbach, and Cohen2 reported the existence of subgrains, about l000Å in diameter, in retained austenite and suggested that they may be delineated by a subboundary carbide. This raised the possibility that carbide precipitation might be responsible for the hardening reported by Hanemann. In view of these conflicting possibilities, an investigation" was carried out on a high purity, Fe-C alloy containing 1.7 pct C in order to clarify the nature of the phenomenon involved in the reported hardening of retained austenite. This investigation involved correlation of changes in microhardness and microstructure of the austenite as a result of tempering. Microhardness tests were made with a Tukon tester using a 25 gram load and a Vickers diamond. It was found that two groups of austenite hardness values were obtained after tempering at a series of temperatures up to 450°F, which was the highest temperature at which retained austenite regions could be identified microscopically. One group represents a high hardness level which in-

Jan 1, 1955

Lewis, B. LINDEMUTH, ?New York, N. Y.-I would like to confirm Dr. Howe's supposition that a process could be worked out for steel along similar lines. About 1 ½ years ago, F. D. Carney and myself were working on the elimination of columnar crystals which are particularly evident in nickel steel. We discussed rotation and varying speeds of rotation, but figured that with just rotation the steel would eventually catch-up to the motion of the mold and that the desired effect could not be obtained in that way, so we decided to alternate the direction of rotation. We rigged up in ordinary commercial turntable and on the same mounting attached a blast, furnace and mud gun, which is a simple steam cylinder, and mounted an 18-in. ingot mold on the turntable. The turntable had a stroke of about 10° to 12°, with stops at the ends. The steam cylinder would bang the table against the stops so that the stopping was so violent that it would tend to keep the metal in motion when the mold stopped and thus wash away any crystals that would form. We made quite a few interesting experiments; the results of which were that the columnar crystallization was entirely eliminated. At the same time we cast ingots in a similar mold, allowing the molds to remain stationary; these showed columnar crystals of from 2 to 4 in. in depth. The grain structure of the balance of the ingots, which were rotated, was very much finer than the grain structure of the ingots that were cast and allowed to cool slowly. The experiments were made on a 0.35 per cent. carbon nickel steel, which is probably more susceptible to columnar crystallization than any other. I think that the rolling properties and the forging properties of some alloy steels could be very much improved by a similar method, or some commercial method of casting ingots to eliminate this columnar crystallization.

Jan 5, 1919

By Douglas R. Cook

The urgent need for new base metal ore discoveries was discussed by various authoritative exploration personnel at a CIM symposium on the future of the Canadian mineral industry held at Ottawa in 1967. Data presented at this meeting showed that approximately 150 new mines have started or restarted production in Canada since 1955. Over half of these mines were discovered prior to 1950. The distribution of Canadian ore discoveries during the last 15 years (shown in Fig. 1) illustrates a striking reduction in the discovery rate in recent years in spite of increasing exploration expenditures. These data indicate that $20 million is now spent in exploration for every significant metal deposit found, and evidently the cost of discovery is still rising. Even fewer discoveries are being made in some other important continental areas of the world such as Africa, Australia and South America. The discovery record in the U.S. is thought to be more rewarding than in Canada because the new deposits appear to be substantially larger. Fortunately, most good base metal ore deposits have attractive investment re- turns to justify large exploration expenditures. The magnitude of the exploration expenditures and the increasing need to develop additional metal resources justifies a critical review of the procedures used in the search for ore deposits. Of particular concern is the need to improve the use of exploration techniques in the attempt to obtain better discrimination and efficiency. There is a tendency by inexperienced exploration groups to think of any geological, geochemical or geophysical anomaly as an exploration target and ignore the fact that anomalies can result from many factors other than economic concentration of metals. The desire for a unique and favorable explanation of exploration data often results in too rapid a movement from the reconnaissance to the drilling stage without the use of all the relevant information.

Jan 7, 1968

By Fred R. Harris

INTRODUCTION MacMillan Tungsten is located in northwestern Canada on the border of Yukon and Northwest Territories at a latitude of 63º17' and altitude of 1800 m above sea level. The deposit lies within the Selwyn Mountains 10 km from the Canol Road. It is 660 km by road from Whitehorse, Yukon, and 1325 km by air from Vancouver, British Columbia. MacMil lan Tungsten is a contact metasomatic deposit in gently dipping Lower Paleozoic limestone and limestone breccia adjacent to a Cretaceous quartz monzonite stock. Four tabular tungsten skarn horizons contain total geological reserves of 30 million tons grading 0.9% WO3. DISCOVERY AND HISTORY J.F. Allan, a former AMAX geologist, located mineral claims in September, 1962, to cover the source of scheelite-bearing skarn float found in the headwaters of Cirque Lake Valley. Exploration work on the property conducted mainly between 1968 and 1973, includes geological mapping, 10,500 m of diamond drilling in 73 holes, and 735 m of underground exploration. Mil 1 tests were carried out on a 300 ton bulk sample obtained underground. Preliminary feasibility studies, collection of weather data and a variety of environment studies have been carried out since 1973. Although no production date has been set MacMillan Tungsten will undoubtedly be a major tungsten producer.

Jan 1, 1976

By W. G. Pfann

Formation and slow solidification of a molten zone in a homogeneous ingot produces a discontinuity in solute concentration at the boundary of the zone and a gradient of concentration within the zone. By using two solutes, one a donor, the other an acceptor, step or graded pn barriers can be produced. EXPLOITATION of the difference in concentration between a molten solution and the solid which freezes from it is continued in this paper. The normal segregation which results from this difference has been used for purification'.'2 and for pn barrier-formation in semiconductors."4 By means of traveling molten zones this difference has been used to effect multistage separations and to eliminate segregation in ingots." a It will be shown here that by means of stationary molten zones this difference can be used to produce discontinuities in concentration. In particular it will be shown that a pn or npn barrier can be made by the simple act of melting and refreezing a portion of a block of semiconductor, provided that the block contains proper concentrations of a donor and an acceptor in solid solution. Assumptions The operation of melting and slow refreezing will be called remelting and the interface between liquid and solid at the start of refreezing will be called the remelt bormdary. While remelting may be done for various shapes of starting crystal and remelt zone it will be assumed that the remelt zone is cylindrical, its length being measured in the direction of freezing, which is normal to the remelt boundary, and

Jan 1, 1955

By Henry Louis

The object of the present paper is to describe a primitive method of gold-extraction, practiced by a small colony of Chinese in the district of Tomoh, one of the Siamese-Malayan States. This district has been worked for gold about 150 years, but has been only twice or thrice visited by Europeans, who are looked upon with a good deal of jealousy by the miners. The gold-district, covering not more than 10 square miles, is situated about Lat. 5' 47l N. and Long. -101' 39 E., on the headwaters of the river Teluban. It is a very mountainous region, lying on the northern flanks of the great range that forms the watershed between the rivers Patani, Kelantan, Teluban, etc., on the north and Perak on the south. The gold occurs in narrow veins and leaders of quartz, intersect- ' ing and intercalated among irregularly upheaved and contorted, highly metamorphosed, micaceous and chloritic schists. These veins vary between 3 inches and 3 feet in thickness, and are sometimes very rich. The geology of this region is thus very similar to that characterizing gold-regions all over the world; if must, however, be.

Jan 1, 1892

By H. E. Lee, P. C. Feddersen

Blast-fuRnace operation at the Bunker Hill smelter deviates somewhat from common practice. Under existing conditions it is economical to operate the furnaces at "forced" capacity. The furnace feed consists chiefly of sinter and averages close to 50 per cent lead. Experience in smelting such material favors a low charge column attended by smaller proportions of coke and a low blast pressure. Under such conditions the gain in furnace tonnage greatly overbalances the somewhat higher slag losses and increased percentage of material fumed Furnace Charge The ingredients for the blast-furnace feed are stored in a group of 24 charge bins (3600 cu. ft. capacity). Each bin has two discharge chutes. Beneath each chute is a steel weighing hopper, suspended from a Fairbanks scale. The several hoppers are kept filled with the exact amount of material required to complete a furnace charge. The weighed material is discharged into a standard-gauge, bottom-dump charge car containing two compartments, each of which holds a complete charge (approximately 1½ tons). It is hauled to the blast furnace by a 44011 electric trolley locomotive. The proportionate parts of the various constituents of a representative blast-furnace charge are shown in Table 1. Table 1.—Representative Blast-furnace Charge at Bunker Hill Smelter Material Pounds Sinter.................................................. 2500 Limerock............................................... 0- 50 Coke................................................. 250-300 Scrap iron.............................................. 0-25 Settler skulls.......................................... 75 Undried zinc-plant residue................................ 0-200 Siliceous ore............................................ 25 Baghouse dust.......................................... 0-50 By-product slag......................................... 100 A variable stock tonnage of zinc-plant residue and return by-products results in fluctuations in the percentages of these materials in the blastfurnace feed. Accompanying such variations are corresponding increases or decreases in the amounts of coke, limerock and scrap iron necessary to obtain good furnace operation and adequate reduction.

Jan 1, 1937

By J. D. Audley Smith

Heine's " blue test" for copper, as described by the authorities generally, calls for a set of standard colors; and there has been some discussion concerning the relative superiority, for this purpose, of sulphate and nitrate solutions. The whole matter evidently hinges on the preservation of the standard colors in well-stoppered bottles. The apparatus described by Q. L. Heath* cannot be much improved, when very accurate readings are required. The following method was devised for the purpose of doing away with preserved sets of standard colors, by making a fresh standard for each batch of assays. The solutions are prepared in the usual way, each ammoniacal solution being filtered into its separate bottle, and then filled up to the containing-mark and thoroughly mixed. A similar color-bottle, with an " S " etched upon it, to distinguish it from the other bottles, which are numbered to correspond with the samples, is kept to run the standard. About 150 C.C. of water is put into it, and then the amount of acid (sulphuric or nitric) present in each determination, followed by 30 C.C. of ammonia (s. g. 0.90), which should make the mixture strongly ammoniacal. The liquid is now made up almost to the containing-mark (200 c.c.), say within 1 C.C. The lowest assay is selected first and placed alongside the standard, which, at the beginning, contains no copper. A copper-solution is then dropped into the standard from a burette ; and after each addition the bottle is well shaken and compared with the assay-sample. This operation is repeated until the two shades match exactly, when the burette is read and the assay-result is calculated. The assay next in order of depth of color is now taken and treated in the same way, and so on, until the batch is completed. It

Jan 1, 1901

By John S. Rinehart, Norman Ahlquist

The model which Birkimer has developed to explain the increase in fracture strength of brittle, rock-like materials with increasing rate of loading may have some applicability. It should be noted that since his analysis presupposes elastic behavior he could equally well express his result as an increase of stress to fracture with increasing strain rate, a fact which is well known. Certainly his experimental results do not contradict his strain rate to the one third power law. On the other hand, we do feel that the data are insufficient and inadequate to establish the relation- ship definitely. 'In metals, the whole fracture picture is greatly complicated by concomitant plastic flow and, in rocks, by the presence of macroscopic flaws and inhomogeneties. Both lead to uncertainties as to the state of stress during the fracture process. He quotes in support of his theory Rinehartfs results on rock in which the latter found that under impulsive loading by explosives, rocks appear to be many times stronger than under static loading. We suspect that the observed increase has little specific relevance to the theory which Birkimer puts forward. Rinehart's measurements were made by spalling rocks using a sawtooth shaped stress wave of known intensity and duration. The rise time of such a pulse is essentially zero, certainly less than 0.1 microseconds, so that it is not possible to apply Birkimerfs theory quantitatively. We favor attributing the increase in fracture strength to two factors. First, the action takes place very quickly in an exceedingly thin region so that statistically the probability is small of encountering one or more of the large flaws that contribute so significantly to the reduction of strength of most rocks under tension. It is also conceivable that the compressive wave that has just passed by the region of fracture has strengthened the rock by collapsing some of the larger flaws. Second, the state of stress obtaining at the time of fracture is not all that existing when the

Jan 1, 1971

By J. V. Emmons

THE processes of hardening and tempering steel tools within the past 15 or 20 years have been so developed that the forward strides of the industry can scarcely be followed by the average observer. No small part of the credit for this phenomenal advancement is due to the improved methods of measuring the high temperatures necessary. Pyrometry has made possible the discovery and use of the many special alloy steels the wonderful properties of which are revolutionizing the industrial world. So sensitive are these steels to changes of temperature that often a variation of only 10° F. at a critical point of the heat treatment will cause the failure of the tool. In the tool-manufacturing industry today, accurate control of the many heating operations is imperative. The principal processes in the manufacture of tools that require accurate high-temperature measurements are annealing, carburizing, hardening, tempering, and laboratory research. Several other operations, such as forging and straightening, use rougher and correspondingly less accurate methods. These operations are usually performed in the following approximate ranges of temperature: DEGREES F. DEGREES F. Annealing 1000 to 1700 Tempering 200 to 1200 Carburizing 1400 to 1000 Forging 1400 to 1800 Hardening 1400 to 2500 Straightening 300 to 1300 Laboratory research covers the entire range. Annealing and carburizing are usually done in muffle or semi-muffle furnaces, heated with coal, coke, oil, gas, or electricity. Many of them are of large size, holding several tons of steel at one charge. Both indicating and recording pyrometers are used. The recording instruments are generally of the thermoelectric type, while for the indicating, both optical and thermoelectric are used.

Jan 9, 1919

By F. Weinberg

WHEN impure Zn (< 99.99 pct)&apos;&apos;Z or Zn-Cd alloys3 are progressively solidified, a cell or "corrugation" substructure4 is produced in the solid, with a high impurity or solute concentration along the cell walls. When these materials are polished and suitably etched, etch pits are often observed along the cell walls. For the Zn-Cd alloys these etch pits have been associated with decorated dislocations, present in the corrugation boundaries to accommodate the lattice strain. In the course of an investigation of Zn-2 pct Au alloy, molten metal of this alloy was poured into cold water and the resultant solid pieces were sectioned, polished and etched with a Cr0 ethant. An extremely regular cell pattern was observed on the etched surface, similar in general to the corrugation structure previously reported for impure zinc and Zn-Cd alloys. At higher magnification, regularly spaced pits were observed along the cell boundaries. An example of the regular cell pattern at the center of a specimen is shown in the center and lower portions of Fig. 1; the top of the figure shows the pattern near the specimen surface. Typical etch pits in the cell walls are shown in Fig. 2. It was surprising that a cell pattern as regular as that shown in the center of Fig. 1 was produced at the very rapid solidification rates used (estimated as > 1 cm per sec). In addition, the distribution coefficient for the Zn-Au system is greater than 1. Accordingly, the center of the cells should be rich in solute and should etch

Jan 1, 1963

By James Boyd

REACTIVE metals are not only those sufficiently radioactive to be used as fuels, such as uranium and thorium, but all metals that will find application in power reactors. It is required of such metals that they be relatively inert or chemically unreactive, dimensionally stable at high temperatures and pressures, and either very absorbent of radioactivity or transparent to it. To gain the right perspective concerning these metals it is necessary at this point to explode some erroneous concepts propounded so often they have become accepted as fact. The first of these is that the great industrial nations, especially the U. S., have reached their pre-eminent position chiefly because they possess abundant mineral resources. Some U. S. mineral economists, echoed by the politicians, have taken this position so often that many of their theories and policies are based on the presence of developed mineral resources as a sine qua non to the country&apos;s greatness. Actually the reverse is true- under a social and political system granting free rein to the initiative and creativeness of its people, many hidden mineral resources that otherwise would have lain fallow have been developed into productive enterprises to the benefit of the national industrial economy. Again, once the proper incentive was furnished, other countries have also been able to establish valuable mineral enterprises in recent years; resources long dormant for lack of a proper economic environment suddenly have become valuable and productive. It is possible to name immediately several nations where such domestic economic developments have had favorable repercussions within the last decade. The absence of productive mines in any country is no indication that workable deposits do not exist within its territory.

Jan 11, 1957

By R. Gatewood

The solution here offered is at once simple and important in its direct and indirect bearings. According to the principles of surface-tension, which will be found sufficiently enlarged upon for present purposes in Clerk Maxwell&apos;s excellent little treatise on The Theory of Heat, a mechanical mixture of liquids will frequently of itself divide into groups, consisting of liquids mixing among themselves but withdrawing from the other liquids. The following simple and familiar illustration will suffice: " If we mix water with alcohol, the liquids diffuse into each other. If we now attempt to mix oil with the alcohol and water, the two liquids separate from each other of themselves, and in the act of separation sufficient force is brought into play to set in motion considerable masses of the fluids." Maxwell goes on to show that this relative energy is one of arrangement, depending on the nature of the fluids and the area of the surface of contact, the act of separation tending to reduce this surface to a minimum consistent with equilibrium; that this surface-tension exists between a solid and touching fluid, either liquid or gaseous, being of one sign or the other, in the case of a liquid, according as it tends to draw itself up into a drop on its surface or to spread and wet the solid. After considering various cases, lie states that which particularly interests us, thus : " When a solid body is in contact with two fluids, then, if the

Jan 1, 1885

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc., may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, together with the names of its president and its secretary, may be published in Mining and Metallurgy or the Directory of the Institute. The members of such a society will not be named individually on the membership list of the Institute, but may at any time be proposed for election as Student Associates or Junior Members of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied by suitable testimony as to character and qualifications, will have special weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership. The Affiliated Student Societies receive the following privileges: 1. A copy of Mining and Metallurgy free; 2. The use of Employment Service; 3. The use of Mining and Metallurgy for publicity purposes, such as printing notices of their activities, etc.; 4. Assistance in obtaining speakers for their meetings, lists of moving-picture films, etc. To retain the privileges of the Affiliated Student Society, its officers must keep in touch with the Secretary of the Institute and advise him of its activities. The foregoing plan is not confined to students in mining engineering or metallurgy. Any undergraduate society of engineers may avail itself of the privileges offered. Societies desiring to be recognized as Affiliated Student Societies are requested to make application to the Secretary of the Institute, giving particulars as to the nature, membership and officers. The following list gives the names of the Affiliated Student Societies as of December 1, 1929, and their presidents and secretaries.

Jan 1, 1929

J. L. McK. YARDLEY,* Pittsburgh, Pa. (written dlscussion ?) .-It is interesting to observe how closely Mr. Hansen agrees with other investigators to the effect that the art of electrolytic zinc has left the realm of mystery. In his introduction, lie has said practically what Thomas French said in his paper "The Future of Electrolytic Zinc. "1 The successful electrolysis of zinc from sulphate solutions has not been an easy matter, and it is only within recent years that the difficult problem of depositing high-grade zinc has been satisfactorily: accomplished on a commercial basis. The principal requisite is. that the electrolyte shall be quite free from certain impurities. The methods by which freedom from these impurities is assured are now very well understood, and with experienced superintendents there is little difficulty in obtaining a high efficiency in that part of the process. When certain underlying principles are recognized, the difficulty encountered in dealing with the filtration of the acid and slimy solutions also largely disappears, although it has been a very serious one to the uninitiated. In the dissolving of the zinc from the roasted ore, there is nothing which any competent chemical&apos; engineer cannot undertake, and any other operations connected with the electrolytic process are either of little or no difficulty, or are common to the retort process. Mr. Hansen also agrees with R. G. Hall&apos;s statement in " Some Economic Factors in the Production of Electrolytic Zinc:"2

Jan 10, 1918

By C. S. Herzig

In the Engineering and Mining Journal of Jan. 27, 1900, there appeared an article by Fred T. Greene, describing a method of measuring stopes by the use of strings, a clinometer and a tape. In the early part of 1899 I had occasion to use a somewhat similar method, for the purpose of accurately ascertaining the volume of a very irregular drift connecting two mines. This drift was an important factor in a lawsuit for $150,000, in which it was necessary to determine accurately the volume originally occupied by the material extracted from the drift. While it is unnecessary to give all details of the controversy, some explanation of the conditions is required for a clear understanding of the following description. This drift was started by the a E." Co. from its workings, in about 7 ft. of ore, and headed toward the " G " property, the plan being to extract all the ore between foot- and hanging-walls, but to take out nothing but ore. As the " G." workings were approached; the ore-body became very irregular and much thinner. It was, however, very closely followed, and where the drift broke through into the " G." workings, the hole was only 11 inches high by 14 inches wide, or just about the size of a man-hole in a boiler.. Thus, this connection-drift tapered sharply; and the very irregular foot-wall sloped toward the " G." workings, and entered them at a place where the stope was only about 3 ft. high, and the ground had already commenced to cave. It may be added that the ore-body was a nearly flat deposit of lead carbonate in limestone, the ore and gangue being quite soft. I was called upon by the " G." people to make the survey

Jan 1, 1901

By William E. Hubbard

During the last decade the known reserves of petroleum in the United States have increased from about five billion to over thirteen billion barrels. From the standpoint of public welfare the existence of these known reserves presents an undeniably favorable picture, but viewed from the position of many a harassed operator the blessing has not always been considered an unmixed one. Along with this increase in excess reserves, curtailment of production has come into being as a matter of necessity and the principle of proration as a matter of equity. As a practical matter it has been considered necessary to curtail the production of old wells as well as that of new wells in a pool. The right of new pools to produce has been recognized, and the allowable for them has come partly from increased market demand and largely from the allowables already enjoyed by the developed pools. The natural result—a downward trend in daily per-well allowables—has been especially felt by Texas operators. This trend may be illustrated by Table 1, which comprises the five active areas in Texas, and from which may be noted the following: 1. The average daily allowable per well has decreased about 53 per cent in three years. 2. Of the 184,000-bbl. increase in total allowable for the five areas, 29,000 bbl. came from the increase in state demand and 165,000 from the combined allowables of the remaining pools in the state.

Jan 1, 1937

By H. A. Kursell

IN pre-war days, the mining industry of Russia occupied in the industrial life of the Empire a place of ever increasing importance. The peak of produc-tion was reached in 1913 and 1914, the years of greatest prosperity, and a rapid growth of the mineral industry seemed assured, especially as regards base-metal mining. Exceptions were the gold production, for which a gradual decline was anticipated, and the platinum out-put which was expected to remain steady. A greater productivity of labor, corresponding to better working facilities was noticeable, and the economic status of the working classes was constantly improving. The tremendous strain on Russia&apos;s economic life caused by the World War did not materially alter the prospects of the mineral industry and the fundamental changes began only with the revolution in the spring of 1917. Their scope and character are illustrated by the figures in Table 1 which compare, for the parts of the Russian Empire under Soviet (R. S. F. S. R.) control, the average mineral production of 1913 and 1914 with that of 1920, 1921 and 1922, as supplied by bolshevik sources.1The latter three years in Russia&apos;s history were characterized by the firm establishment in power of the Communist party as a new ruling caste. Silver, lead, zinc, tin, nickel, tungsten, barite, etc., were either produced in negligible quantities, or not at all. However, before the revolution the development of several argentiferous lead-zinc deposits in western Siberia had reached a stage which seemed to assure an appreciable output of the white metals for the near future.

Jan 7, 1923

Economic Significance of High-grade Concentrates BY PAUL M TYLER AND CARLE R HAYWARD (Min & Met, Dec, 563 4000 words) Generally pyro¬mctallurgical methods yield a higher recovery but cost more per ton of ore treated Milling methods are inherently cheaper for the reason that they do not involve dissipa¬tion of heat energy in slag formation, ctc It is vaguely realized that the smelter man could do a better job if he were supplied with purer raw materials but hard¬headed mill men have been offered little inducement to do a really good job of cleaning concentrates To do this may involve some sacrifice in percentage yield and in mill capacity and unless there is a compensating saving in freight and smelter charges, it simply is not good business to go beyond a certain point in the way of making clean concentrate Opportunities exist for eliminating one or more steps in the expensive series of processes for recovering various metals, or at least reducing the volume of materials that has to be handled at the most costly steps The beneficiation of nonmetallic minerals likewise affords numerous examples of over-all economies obtainable through more refined methods of mechanical improvement All this leads to the conclusion that perfecting selective processes for isolating pure minerals (e g, galena) virtually free from other sulfides as well as gangue may be productive of industrial economies Conversely, cheapening smelting methods may invade the field of mechanical improvement of ores but, as Kiphng said, that is another story

Jan 1, 1937