Search Documents

By Kenneth Cottingham

The number of wells drilled in Ohio in 1943 was slightly in excess of the number drilled in 1942. Compared with the average annual completions for the five years preceding, the year 1943 was short 11 per cent, hut the average initial volume of gas wells was considerably improved. In 1942 the average initial open flow per gas well was 668 M cu. ft., whereas in 1943 the average was 913 M cu. ft. Although no large gas-producing areas were discovered during the year under review, some 30 small pools were found in 17 of the counties of eastern Ohio. These new pools averaged about 300 acres each, and most of them were not extensions but were separate pools adjacent to older production. The Clinton sand furnished most of these discoveries, although six were from the Berea, one was Newburg, and three were shallow sands. No discoveries were made outside former producing counties, and there was no new development the Trenton area of western Ohio. The number of oil wells decreased from 181 drilled in 1942, to 170 in the year 1943. The production of Pennsylvania-grade oil increased 7644 bbl. The total Corning production, however, decreased 91,325 bbl. The present price of Corning-grade oil, $1.31 per bbl., is too low, in the opinion of the operator, to justify exploration. Until something is done in correcting the price level of Corning grade, the production probably will continue to decline. The oil industry in Ohio is making a concentrated effort toward increased production and improved methods of recovering Pennsylvania-grade oil, and a.s this report is written a research and engineering program is being formulated for the benefit and information of the various producers of that grade in Ohio.

Jan 1, 1944

By Walter Miller

Construction of new large refineries was small in 1937, but extensive modernization and expansion of existing plants were made, bearing out the observation of the Bureau of Mines that the trend is strongly toward fewer and larger refineries. Building the first large combination skimming and cracking unit of 20,000-bbl. capacity was a startling achievement four or five years ago, but it has been exceeded many times since, and at least four units with a capacity of 30,000 bbl. or more were contracted for during 1937, as well as many other units of smaller but still substantial capacity. Installation of polymerization plants for producing high-antiknock blending naphthas from refinery gases progressed at an accelerated rate in refineries affording sufficient raw gas to make the use of the process profitable. The total productive capacity of polymerization units built and contracted for in the United States is now about 25,000 bbl., equivalent to the gasoline production from approximately 55,000 bbl. of crude oil a day. Octane Fuels Also utilizing refinery gases—the butylene fractions in particular—the plants for manufacture of iso-octane increased in number to such an extent that the combined capacities will enable the air forces of the United States shortly to go entirely to the use of 100-octane fuel, indications being that the Army will reach that position in 1938, with the Navy not far behind. Commercial air-lines are expected to take advantage of the greater power of high-antiknock fuels to gain the increased power and increased pay loads possible with their use. Work done on producing fuels with octanes beyond the 100 point has recently been reported, and their production can be expected, although at high cost, when the economics of the situation justifies and engines capable of utilizing them efficiently are available. In the field of motor fuels, important work was reported to the A.P.I. at its annual meeting, on the effect of altitude on antiknock requirements

Jan 1, 1938

By Otto F. Pfordte

The great advance of the last twenty years in the specialization, delicacy and efficiency of ore-concentrating apparatus calls for a finer system of testing both the qualities of ores and the operations of machines in this department. In amalgamation, lixiviation and smelting, the daily employment of physical and chemical tests has been recognized as necessary, and the cost of the necessary laboratories and employees is cheerfully paid. But while much progress has been made in concentration (due, in a large degree, to the study of the subject in our technical schools), it is still too common in actual practice to follow the loose old method of roughly estimating, once for all, that a given ore " concentrates x tons into one," and resting on this assumption so long as that ore continues to be treated, while assays of the tailings from concentration are made from time to time, without exact determination of their quantity. The first step toward accuracy of control must be a more frequent and precise measurement of the quantity of concentrates from a given operation. This should be expressed in pounds per unit of one ton; and the variations shown in frequent determinations will furnish a constant check upon the character of the ore and the performance of the apparatus. But this is only a part of what should be constantly and systematically done to insure the best work upon a material which must vary continually, even though it come from one mine only. If, in any mill, appropriate laboratory-tests were made at least once a week, the labor and expense involved would be amply repaid by increased knowledge and control of the current operations. A small testing-laboratory, provided with a few gold-pans;

Jan 1, 1902

By C. E. Feltner

In a recent note, Meleka and Hiarris1 have reported that the application of a constant strain rate Ad a superimposed cyclic stress to 99.99 pct polycrystal-line zinc at room temperature produced some marked effects in the resultant behavior. In their work, one end of the specimen was pulled in tension at a constant strain rate while the other end was subjected to a sinusoidally varying load (20 cps) of constant amplitude. For the slower strain rates and the larger superimposed cyclic loads, it was observed that the specimen could withstand strains prior to failure more than 100 pct greater than the fracture strains obtainable in simple unidirectional straining. This ductility effect was interpreted as being due to a cyclic stress enhanced thermal recovery process. It is the purpose of the present note to describe some related effects in 99.99 pct polycrystalline cadmium. Specimens were loaded in repeated tension at room temperature with a stress of sufficient magnitude to cause failure in about 1000 cycles and the accumulated strain was measured as a function of cycles and time. In addition, some specimens were subjected to a steady creep stress equal in magnitude to the peak value of the cyclic tensile stress. The resultant strain-cycle and strain-time curves for both types of test are shown in Fig. 1. It should be noted that the static creep specimen failed in about one third the time required to produce a cyclic failure but in the cyclic test the specimen was able to withstand a uniform strain before necking more than 50 pct greater than that possible

Jan 1, 1963

By James A. Barr

Prospecting methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the "grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist† who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals in chemical corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by small, temporary, hand-dug shafts.

Jan 1, 1948

By C. L. Berrien

BEFORE the present company was formed, in 1916, each group of mines comprising the old organizations made its detailed daily and monthly mine cost records along the lines used before the consolidation; that is, there was no attempt made to standardize and compare the stope costs of all mines. The general cost sheets for all mines, however, were standardized, and cumulative labor cost sheets were compiled in the general superintendent's office. At most of the mines, a daily record or distribution sheet for each working place was kept, showing the number of men, hours of drilling, hours of timbering, hours of tramming, cars of ore, cars of waste, sticks of powder and feet of fuse. This information was kept by each shift boss and entered on the distribution sheet by him or, at some mines, by a tram boss. The superintendent solved his own problems under the direction of the general superintendent, but without coming in touch with other superintendents, either through records or general conferences. Probably 95 per cent. of the stopes were square-set worked by day's pay; there were some back-filling and shrinkage stopes. Many of the development places, such as shaft sinking, station cutting, drifting and raises had always been run by contract. These contracts were given, for no definite period, at so much per linear foot and were measured monthly, or when completed; the men being paid monthly. In some cases, fairness to the employee, was not maintained. On the whole, there was no standardization. There were no stope contracts, because of the objections of the Western Federation of Miners to general contracting in the mines.

Jan 2, 1922

By Ernest Burchard

A RECONNAISSANCE Of the manganese-and chrome-ore deposits of Cuba was made by the writer, as a representative of the U. S. Geological Survey, in company with Mr. Albert Burch of the Bureau of Mines under instructions of the Secretary of the. Interior, in the Spring of 1918. The object of the study was to obtain authentic information for the use of the United States Government as to the location, character, quantity, and availability of the manganese and chrome-ore deposits in Cuba. Accordingly, the work comprised the examination of such deposits as seemed to be of promise, without regard to stage of development, with a view to determination of the quantity and quality of ore likely to become available for shipment during 1918 and 1919, and of the tonnage of ore in reserve. While it was possible to visit most of the deposits that seemed to be of promise, there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Manganese ore is found in Cuba in Oriente, Santa Clara, and Pinar del Rio Provinces, but in Oriente Province only does it occur in large commercial quantities. There, the deposits are in three areas: one north of Santiago de Cuba, one south of Bayamo and Baire, and one on the Caribbean coast between Torquino Peak and Portillo. In Santa Clara Province, a little ore has been found near the Caribbean coast west of Trinidad; and in Pinar del Rio Province, manganiferous material occurs north of the city of Pinar del Rio and farther west near Mendoza. The manganese ores of Cuba occur, principally, in sedimentary rocks, such as limestone, sandstone, and shale, that are in places metamorphosed, and. in beds that originally may have been water-laid tuff

Jan 3, 1919

By O. A. Knight

THE suppression of the austenite-martensite transformation that can be brought about by the addition of certain alloying elements, such as manganese or nickel, to plain carbon steel has been known for a long time, especially since Guillet's investigation at the beginning of this century. The extent to which the critical range is lowered depends upon the percentage and nature of the special element added. First the Ar1 point is lowered gradually, then at a certain percentage a sudden lowering to about 300° C. occurs. The addition of still larger percentages of the alloy may result in lowering the Ar1 point to room temperature or below, in which case the steel remains austenitic at room temperature, especially after rapid cooling. The effect of alloying elements of this general type on the lowering of the transformation temperature is well illustrated by Sauveur(1)§ in his Fig. 281a, reproduced here as Fig. 1. This type of curve is characteristic of both manganese and nickel though it requires about 2 1/2 times as much nickel as of manganese to produce the same result. The influence of nickel in retarding the transformation of austenite into the lower transition constituents is due to its lowering of the critical range of the steel, which is also well illustrated by Sauveur(1) (after Osmond) in his Fig. 284, reproduced here as Fig. 2. Scott(15) presents a diagram illustrating the effect of manganese on the Ac3 and Ar3 points which is strikingly similar to the diagram above referred to in Fig. 2 concerning the effect of nickel.

Jan 1, 1934

By James A. Barr

Prospecting methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the "grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist† who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals in chemical corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by small, temporary, hand-dug shafts.

Jan 1, 1948

By J. Walter Scott

IT is usual practice in the copper industry to use open horizontal molds for casting tough-pitch copper wire bars.1 A wire bar cast in this manner is partly characterized, by heavy wrinkles and a comparatively deep skin of oxide on the top of the bar, corresponding to the open side of the mold. On the theory that the rough, high-oxide surface might have an adverse effect on the rolling and drawing properties of a wire bar and might account for some of the irregularities of mill behavior, several bars which had been planed to remove the wrinkled surface were processed into wire. These bars responded to mill treatment more satisfactorily than did the regular wire bars. Realizing that machining the surface of one face of each bar would not be commercially feasible, it was decided that casting the metal into a vertical mold and cropping off the pouring end would accomplish. approximately the same result. Several wire bars of commercial size (250 lb.) were so cast and processed into wire for comparative test with bars cast in the usual horizontal molds. It is the purpose of this paper to present the results obtained from this investigation, in which commercial bar sizes and processing technique were used throughout. The results show that in general copper wire bars cast vertically are superior to those cast horizontally.

Jan 1, 1930

By A. K. Sinha

The annual production and productivity of underground coal mines in recent years declined from 334 Mt (368 million st) and 14.5 t (16 st) per man per shift in 1969 to approximately 254 Mt (280 million st) and less than 8 t (9 st) per man per shift in 1977. Productivity is still hovering at about 7.25 t (8 st) per man per shift. According to US Bureau of Mines, the estimated US coal reserve is about 396 Gt (437 billion st), 68.65% of which is obtainable by underground mining methods. Approximately 153 Gt (169 billion st), or about 85.2% of the high Btu premium coking coal of the eastern US, would need to be extracted by underground mining methods. It is thus apparent that under- ground mining will continue to play a major role in total US coal production, which is expected to rapidly increase to about 1.1 Gt (1.2 billion st) by 1985, with about 606 Mt (668 million st) being contributed by underground mines. Production Potential of Continuous Mining The production potential of a continuous mining section depends primarily on the producing ability of the miner, transporting ability of the face haulage, and the matching of the two systems. The producing ability of the continuous miner depends on its actual cutting ability and the time available for cutting coal. The performance of 10 continuous miners operating in coal seams of various thicknesses were monitored in Pennsylvania and West Virginia, using continuous electrical power analyzers and time studies. The recordings on current and power strip charts yielded an accurate analysis of the cutting, trimming, and idle times of the machines on a full shift basis. Continuous miners of various models and sizes from 112-298 kW (150-400 hp) were monitored. Based on actual cutting time, the average cutting ability of the machines, as shown in [Fig. 1], ranged from

Jan 1, 1983

By R. H. Johnson

The Manual of the Oil and Gas Industry, under the Revenue Act of 1918, published by the Treasury Department for the guidance of oil companies in preparing their estimates of future recoverable oil for the purpose of calculating depletion, gives the first large public collection of comparative decline curves for the whole country. It is a matter of both scientific and practical interest to so arrange these data that the pools can be readily compared. There are certain difficulties in such a comparison, however: (1) The economic limit varies from 50 to 2000 bbl. a year in different pools taken. (2) Because of this variation in economic limit, the range of data shown makes comparison possible only for wells of intermediate size. In order to be as inclusive as possible, I have taken as an expression of the rate of decline the amount of oil produced in the period during which a well drops from 3000 to 2000 bbl. a year. No period of smaller production could be used because of the high economic limit in California; and no period of larger production and yet include the small well areas of the Appalachian. As it is, the Lima-Indiana wells are excluded. In a few instances, curves were extrapolated to obtain the reading, where the curve seemed regular enough to warrant it. In general, the amount of oil, in barrels, produced while a well declined from 3000 bbl. to 2000 bbl. a year is shown in Table 1.

Jan 1, 1921

By F. H. McDowell

The electro-magnetic separator of Mr. G. Conkling, Glens Falls, N. Y., described by Mr. Birkinbine* in a paper at the New York meeting of the Institute, in February, 1889, has been in successful operation at the Tilly Foster 'mine for a considerable period, under the disadvantages which seem to be the inevitable attendants of pioneer enterprises in new technical fields. The results of a run of several months, which the Superintendent, Mr. S. P. Tomkins, has taken pains to collate, are here presented by his courteous permission, and that of Mr. E. S. Moffat, the energetic and skilful General Manager of the Lackawanna Iron and Coal Company, to whom our profession is already indebted for examples of bold and ingenious practice in mine-engineering. It is believed that these figures will assist those who are planning similar operations to decide intelligently what they may, and, more important still, what they may not, expect to accomplish. The local difficulties in the way of this experiment at the Tilly Foster mine were many and great. Only about two-thirds of the waste-dump, resulting from the assorting of previous years, is ore; and this varies in content of iron from 20 to 28 per cent. The remainder is rock, some (from horses in the vein) showing particles of adhering mineral, some (from the foot- and hanging-walls) entirely barren. The expense of overhauling the dump and removing this rock is by no means the least of the numerous items which must be charged against the concentration. Associated with the lean ore are hornblende and other minerals, carrying iron in the non-magnetic state, which must necessarily be washed away with the tailings. The waste-dump was originally located without reference to future treatment, and now can only be handled by means of a locomotive,

Jan 1, 1891

By R. J. Armstrong, J. J. McKay

The Montana Phosphate Products Co. is currently operating three underground phosphate mines in Powell County, MOnt. † In this area the Phosphoria formation is from 35 to 50 ft thick and contains a bed of phosphate rock varying in thickness from 2 1/2 to 5 ft, overlain by 12 to 30 ft of cherty quartzite, and underlain by about the same thickness of quartzite and shaly to cherty beds. In general, the phosphate bed has a reasonably hard quartzite footwall, as well as a hard cherty hanging wall, both of which greatly facilitate the mining operation. Folding has deformed the phosphate bed to a considerable degree in the area. It is carried to surface by several of the anticlines and lowered to considerable depths in some of the syn-clines. The main structural features affecting the mining operations of the company are the Garrison anticline and the adjoining syncline and succeeding limb of a second anticline on the east (Fig I). The axis of the folding strikes roughly northwest-southeast. The three mines, namely, the Anderson, Graveley, and Luke are on different limbs of the above folds. Accordingly, the dip of the bed, and consequently the mining method, in each mine differs to a considerable degree from that of the others. For this reason, each operation will be dealt with separately. Anderson Mine LOCATION AND DEVELOPMENT Topographically this mine is in a narrow valley, the bottom of which has an altitude of 5200 ft. The phosphate bed outcrops near the ridge on the east and dips towards the valley floor at an angle of from 25 to 30°,

Jan 1, 1950

By S. Y. Han

INTRODUCTION More than 97% of the total uranium production of the United States comes from sedimentary deposits (1). These sandstone deposits were formed by reduction of migrating uranium-bearing solutions from volcanic silicate rock sources. Such deposits occur in two major forms, either as relatively flat, lens-like deposits or as crescent- shaped roll front deposits. The lens-like deposits are found as discrete masses enclosed in reduced sandstone which is generally surrounded by oxidized sandstone. The roll front deposits are found along crescent-shaped interfaces between reduced and oxidized sands tone (2). In-situ mining of selected sedimentary deposits has proven to be a viable method of extraction and competitive with conventional mining for relatively deep low-grade ores (2). In in-situ leaching, uranium is recovered by drilling injection and collection wells in the ore body, pumping a suitable lixiviant to dissolve the mineral, extracting uranium from the pregnant solution by ion exchange, and finally regenerating and recycling the lixiviant. Even though there is increasing interest and practice in developing the in-situ technique for obtaining uranium values from deeper, lower-grade reserves, there is a lack of knowledge of the basic leaching kinetics and combined transport processes. In-situ leaching operations, in general, appear attractive for the following three general types of deposits (2): (1) low-grade surface dumps or deposits which lie above the natural water table,

Jan 1, 1983

By J. A. M. van Liempt

SINCE the discovery, of von Laue, that a crystal forms a natural grating for X-rays, our knowledge of the structure of solids has gone forward with rapid strides. This progress is not only of purely scientific interest, but has also yielded direct technological results. One of the most valuable results is the broadening of our knowledge of the structure of pure metals and alloys. To promote these studies it is often desirable to have at our disposal pieces of metal consisting of one single crystal. As is so often the case in the natural sciences, we obtain the best results by making our earliest experiments on pure, simple materials and avoiding unnecessary complications. The Cryogen Laboratory at Leyden followed this method with much success, because the work was done at such low temperatures that the heat movement of the atoms was almost' absent. Similarly we can simplify the studies of metals by leaving out of consideration the influence of the grain boundaries and the mutual influence of the crystals by using unicrystalline instead of polycrystal-line metal. Methods of making single crystals have been scientifically studied during the past few years. Some methods were already known in the arts, but these have been improved and new methods have been developed. The methods for making metallic single crystals may be divided into the following groups: A. From the liquid state B. From the gaseous state C. Electrolytically D. By recrystallization in the solid state

Jan 1, 1927

By L. B. Lindemuth

To those who are in a position to carry the thought to a conclusion; I would like to present a theory for the cause of blisters in galvanized sheets. Blisters that are caused from piping and shrinkage cavities will not be considered because the reason for their formation is entirely obvious. Blisters that occur periodically with no apparent system of ocation, number, size or grouping, and then disappear with no. apparent change in manufacturing method, are the ones to which this theory would apply. Examination of blisters of the latter type has shown that they contain hydrogen gas at atmospheric pressure, and that occasionally traces of oxide or sulfide are found on the inner surface of the blisters. These two characteristics have led to the rather general idea that hydrogen gas generated in pickling, and that iron oxide supposed to be inherent in the ingot and causing weak spots were, in some manner, responsible for the development of blisters in galvanizing. The theory which I wish to advance is that these blisters are caused by moisture that has penetrated the steel after the annealing operation. This moisture comes from the atmosphere, or from pickling or washing and when it is suddenly expanded into superheated steam in galvanizing, the increase in volume is so great that it cannot escape with sufficient rapidity through the small opening where it entered as moisture.The pressure so generated forces the sheet apart along those lines of lamination ;hat may be found in practically all flat sections of steel rolled comparatively cold. The increase in volume. from moisture to steam at 800° F. is 2244 times the original volume of the moisture. The pressure generated by ;he moisture heated to 800° F. and entirely confined would be enough to expand or explode any container. This would explain the source of sufficient pressure to cause a sheet to blister.

Jan 3, 1927

By H. F. Miller

Fox some years the prejudice against basic open-hearth steel for casting has been gradually decreasing. Yet many consumers and engineers still cling to acid steel for castings, because of their alleged greater freedom from blow-holes and sponginess. Acid steel has been used for this purpose much longer than basic steel; and the melters in acid practice had it well in hand when basic steel was first tried. Then the necessity of learning a new set of laws for the production of satisfactory basic open-hearth steel for castings became evident. The first of these laws, in my opinion, has to do with the furnace construction. The heat should be melted down as speedily as possible so as to prevent excessive oxidation. I have described in another article ' some furnaces designed by me, and having as one of their features the promotion of quick melting. Size of the Furnace. The hearth of the furnace, however, is a decisive factor in the production of solid castings. The manufacturer should know the size of the heats he intends to make constantly, and should have his furnace built for that size of heat. The hearth should differ in dimensions from that of a furnace making ingotr steel. That is, the bath should be deeper and should have less surface-area. A shallow bath permits the slag to come out soon after the steel commences to flow, and thus prevents the additions from going into the steel, or from becoming uniformly distributed in case they have been put in hurriedly. Under this head comes the very poor practice of making small heats in hearths of a much larger capacity. If into a 25-or 30-ton furnace only 12 or 15 tons of metal is charged per heat, the proportion of heats that will be wild, or show signs

Jan 1, 1913

By Carl E. Reistle

ENGINEERS as a group are often criticized because they have been responsible for the development of many technical improvements only to allow the administration of them to pass into the hands of others who may have little understanding of how they operate and little competence in their use. These criticisms are not always justified. There are many engineers who have shown themselves to be great administrators in addition to being great creators or builders, and more and more one sees the engineer demonstrating unusual administrative ability as he moves into the executive ranks. The last five or ten years have seen a new movement developing in this country-a movement brought about through the recognition by business statesmen that successful business administrators and executives just cannot be expected to develop like Topsy, that the management of a company must deliberately take steps to cultivate the proper climate or environment for growth if it wishes to provide an adequate and capable succession of executives in the future. This movement has taken on a number of names-Management Development, Executive Development, Personnel Development-but are these not actually misnomers? Can we develop anybody? In the strictest sense of the word, the author doubts that anyone can change any other person, at least, not much. The change must come from within. Perhaps this movement should be looked at not as a program of developing people but as one of giving people an opportunity to develop themselves. In the Humble Oil & Refining Co. there is an Executive Development Program; maybe it might better be called a Program of Development for Executives.

Jan 8, 1954

By W. R. Hibbard

IN ref. 1, on the basis of tension and torsion experiments with single crystals of a brass, the values given in Table I were obtained for elastic coefficients. It was pointed out by Zener that the values for the 71.2 pct Cu were not satisfactory, since they resulted in a negative value for the bulk modulus, namely —4.17X1012 sq cm per dyne. In reevaluating the data of this investigation, it was determined that the reason for this negative bulk modulus lay in the extrapolation of the reciprocal Young's modulus to the zero value of the orientation function shown in Fig. 5 of ref. 1. This extrapolation was reevaluated by the method of least squares (50 pct probability) and a new value of the coefficient S,, was determined as 18.9220.42X 10M sq cm per dyne in lieu of the value originally reported of 18.82x10 sq cm per dyne. This new value of S, leads to a new value of S, of — 9.43 X101" sq cm per dyne. The values of the other coefficients are unchanged. results. This value compares with the value of 12.3X10 sq cm per dyne reported by Schmid and Boas? The new results are summarized in Table 11. These results follow similar qualitative trends, previously published,' relative to the effect of zinc content. However, the derived values of C11, C,, C,, and K are so sensitive to the uncertainty in the first decimal place of the S, values that they are probably not useful. This uncertainty must also apply to the previous results of Masima and Sachs," who obtained S, values from a similar extrapolation drawn wholly above their data points. Acknowledgments Advice and assistance on the statistical methods were obtained from R. W. Guard. The calculations were carried out by Miss E. Saacke.

Jan 1, 1958