Search Documents

By J. C. Bokros

At temperatures above 950°F, zirconium which has been strained a critical amount will experience critical recrystalli-zation. The large grain size thus formed can result in a reduction in the fatigue life by a factor of 2 to a factor of 9 at both high and low temperatures. The critical strains for zirconium vary from 15 pct at 900°F to about 2 pct at 1125°F, while those for zircaloy III vary from 15 pct at 1050°F to 5 pct at 1200°F. Zircaloy II ,experiences no critical recrystallization up to 1200°F. ZIRCONIUM has become increasingly important for nuclear applications and is being employed in reactors at temperatures where recrystallization can occur. Recent work' on the fatigue properties of zirconium has shown that coarse-grained structures developed in zirconium during recrystallization have much lower fatigue lives than fine-grained material. The development of these large grain sizes under such conditions is well known to be the result of critical recrystallization.2-4 Briefly, critical recrystallization occurs when a metal is strained a critical amount and annealed in the recrystallization range. The critical strain is defined as that minimum strain necessary to promote nucleation in the time unit and temperature considered. The maximum grain size occurs at the critical strain, since at this strain the fewest stable nuclei per unit volume grow into new grains. Recrystallization is not evident below this; strain since the nucleation rate is vanishingly lolw, and metal strained more than the critical amount has a higher nucleation rate per unit volume which results in a finer grained structure. This paper describes the critical recrystallization observed in reactor-grade zirconium, zircaloy 11, and zircaloy I11 as a function of annealing temperature and temperature of strain. EXPERIMENTAL The zirconium used was hafnium-free, double arc-melted sponge obtained from the Bureau of Mines. The ingots were forged and hot reduced to 0.08 to 0.10-in. sheet and subsequently cold reduced to 0.035-in. sheet with intermediate and final anneals at 1200 OF for 15 min. The zircaloy II and zircaloy III used were 0.035-in. sheets in the annealed condition. Compositions of these materials as tested are given in Table I. To determine the critical strain at a given temperature, tensile specimens having a0.065-in. taper in a 2-in. gage length were machined from the sheets parallel to the rolling direction. The specimens were polished, etched, and examined metallographically to ensure that all of them were strain-free, initially. Tukon indentations were made every half millimeter along the gage length of each specimen. These served as fiducial marks enabling the plastic strain to be measured with a microscope and micrometer stage. The specimens were pulled to failure at a rate of 0.002 in. per min in an Instron tensile-testing machine. Three temperatures were used for straining: room temperature, 500 ºF, and 900 ºF. The 500º and 900 ºF tests were run in an argon atmosphere. Since the rate of work hardening changes with temperature, a different critical strain was obtained for each temperature of strain. Specimens, prepared in the manner described, were annealed in vacuunl at various temperatures ranging from 900" to 1200 F for up to 1000 hr, after which they were examined metallographically. The critical strain and the recrystallized grain size as a function of strain were determined for each specimen. Results for the same temperature and time indicated that the critical strain measured was reproducible to within 5 pct of each other. RESULTS AND DISCUSSION Since increasing the time of anneal increases the probability of the nucleation of a new grain, the critical strain decreases with time at a decreasing

Jan 1, 1961

By C. D. Stahl, E. E. Templeton, R. F. Nielsen

It has been customary, in predicting saturation changes, to use the Leverett fractional flow formula", obtained by eliminating the unknown pressure gradient from the generalized Darcy equations for the separate phases. The formula presents difficulties in the case of counterflow, since the "fractional" flow may be negative, greater than unity, or, in the case of a closed system, infinite. Recently, it has been shown by several authors that the corresponding equations (with capillary pressure and gravity terms) for actual flow of the phase may be used just as well. These equations are in agreement with Pirson's1 statement that, if the two mobilities differ considerably from each other in a closed system, the flow is largely governed by the lower value. The present study was undertaken because of an apparent lack of experimental data on gravity counter-/low with which to test the theory. A 4-ft sand-packed tube in a vertical position was employed. Electrodes for determining saturations by resistivity were spaced along the tube, one phase being always an aqueous salt solution. Air, heptane, naphtha, or Bradford crude oil was used for the other phase. A reasonably uniform initial saturation was set up by pumping the phases through the system, alter which the tube was shut in and saturation profiles obtained at definite intervals. Cumulative flows over certain horizontal levels were obtained by integration of the distributions; hence, differentiation of the cumulative flows with respect to time gave instantaneous flow rates. To compare experimental and theoretical flow values, capillary pressures were assumed given by the final saturation-distribution curve. The upper part corresponds to the "drainage" region and the lower part to the "imbibition" region, where trapping of the nonwetting phase occurred. While calculations indicated that the capillary pressure saturation function and, probably, the relative permeability saturation functions changed during the segregation, the relation of the measured rates to saturation distributions are in general accord with the frontal-advance equation. It appears that the Darcy equations, as modified for the separate phases, are generally valid for counterflow due to density differences. The usual method of predicting saturation changes, which involves a continuity equation and the elimination of the unknown pressure gradient from the flow equations, should therefore be applicable. However, the need for advance knowledge of drainage and and imbibition "capillary pressures" and relative permeabilities during various stages presents difficulties. INTRODUCTION The present study was undertaken because of a seeming lack of experimental data relating to vertical counterflow of fluids of different densities in porous media. In particular, it was desired to determine whether data obtained from these laboratory tests were in accordance with certain mathematical treatments of counterflow which have been proposed. The gravity "correction" has been incorporated into the flow equations (and, hence, into displacement theory) nearly as long as both have been used. field4 and laboratory5 data have generally borne out the validity of the theory as applied, for instance, to downward displacement by gas, with all fluids moving downward. However, the modifications for counterflow have only recently been pointed out. 2-3 It has been customary to use fractional flow rates instead of actual flow rates in displacement calcuIations. In the case of counterflow, this results in negative values, values greater than unity and, when rates are equal and opposite, in infinite values. As pointed out by Sheldon, et a1,3 and by Fayers and sheldon,2 actual flow rates may be used just as well. The fact that these may be of opposite signs for the two fluids does not present any difficulty.

By A. J. de Witte

INTRODUCTION The importance of determining dips of subsurface formations in wells, especially in wildcat wells, is self-evident and need not be enlarged upon. Various dipmeter instruments have been described in technical literature1,2,3,4 over the years. The introduction of the continuous dip-meters3,4 has made the earlier types obsolete. Continuous dipmeter logs are run by at least two different major service companies. Included as part of the service are a limited number of dip calculations—usually 10—made at different levels from the log. Very frequently this is the total result of a dip survey. It is believed that dipmeter surveys would be of considerably more advantage if geologists and engineers were able to make their own calculations from the original records. Determination of dips from the dipmeter record starts with the correlation of three log curves taken at different sides of the borehole. It cannot be over-emphasized that the quality of the results hinges primarily on this correlation. Nobody should be better qualified to correlate logs than a subsurface geologist or field engineer. The next requirement is to have an easy yet accurate way of computing the dip from the correlated points. Service companies use a mechanical device for this purpose. Directions for a graphical method were given in a recent article by B. 0. Prescotts. This paper describes a different graphical technique which, in our experience, is simpler, faster and at least as accurate. The entire manipulation is carried out on the stereonet in a number of easy moves. The paper is divided into two parts. This first part contains the introductory sections and full explanation of the geometry involved. The second part reviews the reading of data from an actual field log and summarizes the practical rules for computation of dips, the whole process being illustrated by an example. Following the outlined procedure, one could calculate a good many levels in a relatively short time, thus being able in particular to check suspected anomalies such as fault zones or unconformities in as close detail as the log will permit. GENERAL EXPOSITION OF THE METHOD Prnciple of the Dipmeter The position of a plane in space is defined by the location of three points, not on a straight line. Referring to Fig. I, if a borehole traverses a bedding plane, we can determine the strike and dip of the bed by finding three points which are not in line along this plane. Such points as A, B, and C are obtained with the dipmeter. The device consists of three electrodes (or caliper arms)1, 2, and 3 spaced at 120 angles, as schematically indicated, whose readings are separately recorded (Curves 1, 11, 111, to the right). When electrode 1 passes the boundary of the bed, Curve I will kick, etc. From these curves, we know the relative distances of points A, B, C, measured along the axis of the hole. If A is at zero, then B and C are at levels d1 and d2 up the hole,

Jan 1, 1957

By R. F. Mitchell, G. F. Dillon, A. F. Armington

In this paper the present methods of boron preparation are discussed with emphasis on the iodide intermediate. Several methods of boron triiodide preparation were investigated, the most satisfactory method being the preparation from the elements. A yield of 60 pct based on iodine is found for this method. Zone-refining, sublinzation, distillation, and fractional-recrystallization results are given for the boron triiodide, with distillation producing the best results. Several methods of decomposition are also discussed. The purity of the resulting iodide boron approximates the puritjl of the best available bromide boron, ELEMENTAL boron has been suggested as a possible high-temperature semiconductor by several workers,' but has never been exploited as a device material. The principal difficulty with boron is the unavailability of pure crystalline material from which accurate information on electrical properties could be obtained. Most boron crystals presently produced are very imperfect in structure and of questionable purity, particularly in relation to carbon content. Several methods of boron purification have been reported in the past few years, all of which produce material with a purity better than 99.0 pct. Most of these methods have been the subject of a recent review by Starks' and will not be elaborated upon in this report. However, of all the purification methods reported, only those using halide intermediates produce a purity approaching that usually required for electronic applications. The bromide intermediate has been most used for the preparation of high-purity boron.'y3 This material is easily prepared from the elements and can be effectively purified by distillation and decomposed by hydrogen reduction. The resulting product contains a trace of silicon, and an uncertain amount of carbon, believed to be approximately 100 ppm. It has been recently reported by Russian workers that high-purity boron can be produced using an iodide intermediate.' In the work cited, boron is reported free of spectro-scopically determined impurities, but the reported detection limits are quite high (- 100 ppm). In addition, no data is given on the carbon content of the product. In the present paper, boron triiodide was chosen as the intermediate for several reasons. First, carbon tetraiodide, which could be a major impurity, is reported to be unstable above 200" and hence could be easily separated from the boron triiodide by its decomposition, since temperatures greater than this are attained during the purification process. The low melting point (45°C) and boiling point (20B°C) and the relatively high vapor pressure of boron triiodide should allow the application of any physical purification technique to the material. The possibility of a lower decomposition temperature than that used for the bromide process is another advantage which might cut down extraneous contamination. The iodide, however, does have certain disadvantages when compared with the bromide, the production cost being the most significant. This is the result of a higher halide-to-boron weight ratio, which means more intermediate must be employed. The cost of the starting material is also greater for the iodide. This cost could be considerably reduced however, by recycling the iodine byproduct. Epitaxial growth of boron, which is probably the best method of producing junctions, should be possible with either the bromide or the iodide as the intermediate. However, this has been attempted only on a limited scale up to the present time because of the unavailability of good crystals. The authors have been relatively successful in laying down a heterotaxy of boron on silicon, however. This will be reported at a later date. Several crystalline modifications have been reported for boron, four of which are now believed to be real.' These are the a! and 0 rhombohedral and the a, and 0 tetragonal. In general, the a! rhombohedral is the low-temperature form and the B rhombohedral is the high-temperature form. The tetragonal structures are detected between 1000"

Jan 1, 1964

By W. Rostoker, H. Nichols

It has been demonstrated in previous work1'2 that wetting of aluminum alloys by liquid mercury can cause fracture to occur with substantial suppression of prior plastic flow. This has been interpreted as the action of a critical liquid species in reducing the cohesive strength of a stressed solid at sites of potential crack nucleation. In this way the critical transverse stress for fracture nucleation is reached at much lower stresses than is normally the case. The stresses for both fracture nucleation and fracture propagation are depressed by the same mechanism. In so doing the plastic-energy component of fracture energy is reduced to a level which is of the same order of magnitude as the surface, interfacial, or cleavage energy. Recent work2 has illustrated the influence of dispersed precipitates, cold work, and combinations of these on brittle fracture associated with plastic strains of the microyield order of magnitude. This has been rationalized in terms of the contribution of internal microstress fields to the stress magnifications at points of obstruction of active slip bands in a stressed metal. The presently reported studies on an Al-4-1/2 pct Mg alloy amplify this subject by introducing thermal-mechanical conditions which can produce strain aging. As amply demonstrated by Phillips, Swain, and borall, the tensile behavior of aluminum alloys containing magnesium reveals a yield-point elongation and successive discontinuous elongations over the whole plastic-strain range. This gives a stepped or serrated character to the stress-strain diagram. The yield-point elongation is not temperature-dependent. On the other hand, the discontinuous extensions in the plastic-strain range are gradually suppressed by lower temperatures of testing. At -78"C, only the yield-point elongation persists. The yield-point elongation itself can be suppressed by rapid quenching to room temperature from an annealing temperature of 500°C. The argument presented by Phillips et 1. and Cottre114 is that the yield-point elongation derives from surmounting at a critical stress the restraint to slip by grain boundaries which have been reinforced by appreciable magnesium-atom segregation. The serrated character of the plastic-strain range is the result of rapid strain aging during the test. This is made possible by the inevitable proximity of magnesium atoms to any dislocation line. In the Al-4-1/2 pct Mg alloy there is one magnesium atom for every twenty-two aluminum atoms and, with a coordination number of 12, a magnesium atom is on the average only about two atomic distances from any given lattice site. Rapid strain aging is therefore a reasonable expectation. A study of mercury embrittlement of the Al-4-1/2 pct Mg alloy (commercial designation 5083) provides an opportunity to relate the interplay of grain size, grain boundary restraint to slip and strain aging in the brittle-fracture process. One lot of commercial sheet material of 0.125-in. thickness was used for all of the tests. The specimen shape and test procedures used were the same as those described in a previous publication.2 A range of grain sizes between 0.0057 and 0.0125 mm was produced by various combinations of plastic prestrain and annealing. The coarsest grain was somewhat elongated in shape. In this case the measurement was taken in the direction transverse to the axis of tension as more meaningful to a brittle-fracture process. In the annealed condition, specimens wetted with mercury failed with zero permanent elongation at stresses slightly below the normal yield point, i.e., stresses at 0.05 to 0.2 pct strain. Since this occurs before yield-point elongation can begin, fracture derives from slip contained within individual grains and restrained from propagating across grain boundaries. No significant difference in wetted fracture stress was observed between specimens which had been water-quenched or furnace-cooled from the annealing temperatures. This signifies that the degree of magnesium segregation at grain boundaries

Jan 1, 1964

By F. W. Jessen, F. W. Rols-Hausen

It is the purpose of this paper to present data on brines occurring in the Frio formation of the Texas Gulf Coast, and to show how their composition varies, (1) with depth below the surface, (2) with depth below the top of the formation, and (3) along the approximate strike. The brines vary in chloride content from 3,180 to 73,000 p.p.m., though the average salinity of the salt waters is shown to vary with total depth; the concentration being 35,000 to 40,000 p.p.m. at 3500 to 5500 ft., slightly less than 50,000 p.p.m. chloride at 5500 to 6500 ft. and average 38,000 to 40,000 below 6500 feet. From the analyses available, it appears that the highest concentration of salts occurs in the upper 300 ft. of the formation, while lower salinity is found with increasing depth below this point. The salt waters from wells in Starr County show less concentration of dissolved salts than in any other group of wells farther north along the strike. In all, 116 analyses from 63 fields and 14 wildcats, from depths ranging from 1300 to 11,400 ft. below the surface and from z to 3240 ft. below the top of the Frio, are recorded. Introduction Brines have been studied for many Years in an attempt to solve some of the geologic and production problems associated with the production of oil and gas. One practical application of study of . water analyses is the correlation of waters occurring above, in, or below the producing sand in the same field or throughout the same formation. The Frio formation, the series of sands and shales occurring below the Marginulina zone and above the Vicksburg, is one of the major oil and gas-producing formations in the Texas Gulf Coast. Fossils are rare or absent in the upper Frio throughout most of the area. When available, cuttings and cores, and electric logs were used to determine the top of the Frio. A change in lithology was used to determine this point in most of the wells, and fossils were used in some of the deep wells. It is realized that a change in lithology is not perfect for correlation purposes over long distances and some of the trends may be influenced by the inability to differentiate between the nonfossiliferous Marginulina zone and the Frio. It underlies virtually all the area shown on the accompanying map (Fig. I). Although it is not productive in the updip facies, it has been explored to a limited degree below I2,000 ft. Further more, toward the coast line future drilling to deeper depths should encounter this formation. Although thousands of wells have penetrated or drilled entirely through the formation, very few water samples have been secured from the many sands occurring in this formation and analyzed. Previous Investigation No previous published study has been made of the chemical composition and concentration of waters from the Frio formation. However, one water analysis

Jan 1, 1944

By Whitman E. Brown, Louis J. Erck

The installation in 1948 of a Hum-phrey~ spiral concentrator section at the Hill-Trumbull plant of The Cleve-land-Cliffs Iron Co. is the latest commercial method on the Mesabi Range being used for the recovery of fine iron ore. In two stages of concentration 84 spirals treat approximately 120 long tons per hour of minus ? in. ore. These spirals augment the production of the heavy-density plant which recovers the plus 36 in. iron from the plant crude ore. Structure of the ore is such that, when crushed, about 50 pct of the plant crude is minus ? in. size. After de-sliming in a 66 in. Akins classifier, grinding the classifier product in a ball mill and again desliming in a 78 in. Akins classifier about 15 pct of the crude ore remains to be treated in the spiral plant. Overall recovery of the ball mill feed in the Hill-Trumbull spiral plant during the 1948 season was about 53 pct of the weight and 66 pct of the total iron content. Of the actual feed delivered to the spirals from the 78 in. classifier 64.9 pct of the weight was recovered containing 73.7 pct of the total iron. The average analysis of the spiral concentrate is 55.05 pct Fe and 14.83 pct SiO2. An average of mill assays during the 1948 season is given in Table 1. The Hill-Trumbull plants treat both wash ore and jig-type ore. During the 1948 season spirals were used only on the fine sizes of jig-type ore. At times the deslimed minus ? in. size is of sufficient grade to warrant bypassing the spirals but in the main the fine size is delivered to the 48 first stage spirals and thence to the 36 cleaner or second stage spirals. In the past several years numerous Mesabi Range ores in the fine size cate- gory have been tested by a wide variety of beneficiating equipment. The prodigious amount of research devoted to the recovery of values in the fine ore reflects the dire need of the iron industry to squeeze the last possible unit of iron from the mined ore and to develop suitable equipment and processes to satisfactorily concentrate the leaner horizons as they are encountered in the process of mining. Large governmental and private appropriations have been allotted, new laboratories built, research and technical staffs increased, and operator-manufacturer cooperative agreements applied to hasten the solution of the problem. The University of Minnesota, at its Eighth Annual Mining Symposium in January 1947, dedicated as its objective the bringing to light of technological developments in iron ore beneficiation. Papers were given at that time relating to processes being developed. Specifically, these papers reviewed flotation, Baum jig, selective media concentrator, Hardinge concentrator, Dorrco sizer, heavy media concentration, Hydrotator, and the Humphreys spiral. The Cleveland-Cliffs Iron Co., after encouraging results from tests in a small pilot plant using one full size spiral, made the first commercial installation of Humphreys spirals on the Mesabi Range at their Hill-Trumbull mine, Taconite, Minn. This company

Jan 1, 1950

By B. M. Larsen, T. E. Brower

In two previous paperslJ dealing with the carbon-oxygcn reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity A[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm.; that is, if [C] X [O] is taken as 0.00222, A[O] = [O] - 0.0022[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.3 This quantity ?[O] proves to be substantially independent of carbon content over the range 0.08 to I,z per cent, as well as of the basicity of the slag, and is nearly always within the limits o.o15 to o.oz5 per cent when the bath is boiling normally and is in what we have termed a steady state, Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, ~(01, on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in A[O] level following addition of spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. Variability of Excess Oxygen in Normal Open-hearth Operation The preceding genera' statements refer to the average value of A[0] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining Oxygen from the gas phase above it, Or from added Ore$ faster than it is losing oxygen to the metal; Yet when the bath starts to boil vigorously, the opposite condition may prevail for Some time. The consequence of this lag is a variation of A[o], the interpretation of which in a sing1e heat may not be immediately obvious. This condition is illustrated in Figs. I and 2. In Fig. 1, A[0] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small orc feed causes only a small rise in A[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1948

By F. W. Jessen, James N. Howell

INTRODUCTION The determination of cloud points has to date been limited to rather transparent oils, visual observation of the formation of a solid phase being the criterion for the standard ASTM D 97-47 method. The need for a quiclc and simple method for determining cloud points under dynamic conditions for opaque crude oils became necessary in a study of fundamental aspects of paraffin deposition from crude oils. PREVIOUS WORK The determination of cloud points in opaque oils by viscosity temperature curves is fairly new, Young' described a method employing the capillary tube principle. No information exists relative to the determination of cloud points of crude or refined oils under dynamic conditions. Shock' noticed that deposition of paraffin from crude oils took place at temperatures at or below the temperature at which a sharp inflection point occurred in the viscosity-temperature curve. This observation indicates a possible correlation between this temperature and the cloud point of the crude oil. Reistle and Vietti1 have reported that when crude oils containing small amounts of asphaltic materials were heated to temperatures sufficiently high to solubilize these materials and immediately cooled the pour point of the crude oil was lowered as much as 70°F. Sachanen\ asribes this effect to the action of colloidal asphaltenes in preventing the formation of the crystalline structure necessary to maintain the oil in a rigid state. At high temperatures, asphaltenes are peptized, and the paraffin crystals formed at these temperatures adsorb the colloidal asphaltenes on their surface thereby hindering further growth of the crystals. Reistle" found, however, that such heating and cooling of crude oils had no effect upon the cloud points. This latter work dealt with a crude oil of fixed composition, and the question immediately arises as to the effect of varying the concentration of asphaltic materials on the cloud point. APPARATUS AND PROCEDURE All viscosity measurements were made with a Bendix Ultra-Viscoson. The Bendix Ultra-Viscoson, which consists of a vibrating probe and an electronic computer. measures viscosity by exciting a thin alloy steel blade on the end of a probe by short electrical pulses in damped oscillation at 28 kilocycles. The blade vibrates longitudinally with an amplilude of less than 55 micron or 20 millionths of an inch. Energy to protlucc this excitation is generated in he computer and transferred to the probe through the connecting cable. The oscillating blade is magnetostric-tive, i.e., it is capable of transforming electrical energy to mechanical energy in the ultrasonic range. Ultrasonic waves are produced in the material surrounding the blade by the oscillating motion of the blade causing layers of the material to slip back and forth over one another at a known frequency. The electronic computer calculates the energy required to produce the sliding motion which is in turn proportional to the viscosity of the material. Actual values of viscosity times density (centi-poise X grams/cc) are indicated on the computer and a continuous D-C signal is provided which is fed into a type 153 Electronic Recorder (manufactured by Brown Instruments Div. of Minneapolis-Honeywell Regulator Co.) The liquid sample container was fabricated from a Lucite cylinder and jacketed by a Luicite water bath. Early experiments using glass and steel sample containers were not satisfactory. since the Ultra-Viscoson was apparently affected by the alterzltion of the magnetic fields surrounding the probe by stresses set LIP in the glass and steel as it cooled. The procedure for determining viscosity-temperature curves was relatively simple. The temperature ot the sample was raised sufficiently high to solubilize all paraffin and asphalts present. After heating, the oil sample was immediately transferred

Jan 1, 1957

By Andrew B. Crichton

The oft repeated statements of the United States Geological Survey and the Bureau of Mines that the coal reserves in the United States are sufficient for 3000 yr have given us all a sense of security hard to disturb. If we discount that statement 66 pct, which to the uninformed seems drastic, we would still have 1000 yr supply, and why should mortal man worry about the difference between 1000 and 3000 yr supply of coal. That is exactly the attitude which many who should be better informed have taken toward the problem. A recent brochure "How Strong is America," by the New York Herald Tribune, states there is "no end to coal * * The truth is staggering * * U. S. has enough coal to last 4000 years." What the statement actually means is that the calculator got as high as 4000 yr and decided it was pointless to go on. The President's ERP Committee on Natural Resources and others in high places continue to assure the country of our superabundance of coal. In the past few days the "Wall Street Journal" carried an item from Director Boyd of the Bureau of Mines saying that within a hundred years we would need to triple our annual coal production of 600,000,000 tons, making it 1,800,000,000 tons annually, and at that rate we had coal reserves sufficient for 1000 yr. In my humble opinion, we cannot now or ever produce 1,800,000,000 tons annually, because we do not have the reserves in the producing districts to do it. Past reckoning in geology may be, as in the Psalms, a thousand years are as yesterday, but the future must be considered more realistically, and " a thousand years" is really a "heck" of a long time. In most developed areas, mining engineers can count the coal reserves in terms of a hundred years or less, and in some important areas now producing large annual tonnages in much under fifty years. They think when they hear of thousands of years coal reserves, reference is made to distant fields and "the fields are always green far away." The estimates of our coal reserves upon which we are relying were made in 1907 under the direction of Marius R. Campbell, Director of the United States Geological Survey. It is apparent this work was not well done. It was necessarily based on rather meager data because of the little development and prospecting as of that date. There were mistakes in the correlation of seams, and they assumed the continuity of thick seams throughout large coal bearing areas where coal often did not exist. The overstatement of coal bearing areas in the Campbell figures are common. The 1907 survey includes all coals over 14 in. in thickness to a depth of 3000 it. The total coal reserves according to Campbell were 3157.2 billion tons. The production and mining losses that year would amount to 570 million tons and

Jan 1, 1949

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953

C. W. Kempton, Oro Blanco, Ariz.: In his interesting paper, Mr. Ingalls refers to reports of tin-deposits near Sain Alto, Zacatecas, Mexico. During 1891 I made some personal examinations of these deposits. They are, for the most part, located from 10 to 30 miles west of the town, in the Sierra del Fraile.

Jan 1, 1896

By C. O. Dale, W. J. Rundle

THE upper Mississippi Valley zinc-lead area was the first major lead-producing section in the United States. The lead ore, found near the surface in crevices, was relatively pure galena that could be smelted directly into lead, at first in log hearth furnaces and later in more efficient blast type furnaces. French Canadian fur traders encouraged the Indians to mine the lead ore and showed them how to smelt it into lead that had a high value for bullets1 Nicholas Perrot found lead ore on the Mississippi River bluffs near the junction of Wisconsin and Illinois and in 1690 established a trading post on the Wisconsin side of the river opposite the present site of Dubuque, Iowa.2 Shortly after 1720 discovery of Mine La Mott in Missouri diverted considerable attention from the Upper Mississippi area. Mining continued on a desultory basis with operations concentrated in the Galena, Illinois-Dubuque, area. In 1740 at least 20 miners were at work in the Fever River area around Galena and are reported to have shipped 2500 70-lb pigs of lead to Kaskaskia in 1741." Julien Dubuque established a mining and smelting operation in 1790 near the city that bears his name and was granted sole right to exploit the mining operations on the lands of the Sauk and the Fox Indians. He is reported to have produced 30,000 70-lb pigs of lead in 1805. Following the death of Dubuque in 1810 the Indians refused to let the white miners enter their lands, and little was done on the Iowa side of the river until the Indians were removed by treaty with the United States government in 1832." Early mining was entirely for lead but as the crevices were followed down, increasing percentages of zinc sulphide and zinc carbonate were encountered and at first discarded. Later a market became available for the zinc ores, and hand jigging devices were made to separate the lead, the zinc, and the rock or waste materials. The first record of zinc production from the area is for 1860. Production of zinc passed that of lead before 1900, reached a peak of 64,000 short tons in 1917, fell off rapidly and continually to about 2000 short tons in 1938, and since 1940 has ranged from 11,000 to 19,000 short tons. Lead has been of considerably less importance since 1900, and at present only about 10 pct as much lead as zinc is produced. Practically all of the zinc ore has come from orebodies that are rather flat and wide with considerable length as compared to width. Most of the early lead came from the crevice type deposit, but present production is from the predominately flat zinc orebodies. The Graham-Snyder orebody, scene of Eagle Picher operations, is practically all zinc with little or no lead being recovered. Marcasite, present in varying amounts, makes production of finished concentrates by gravity separation impractical. Satisfactory lead and zinc concentrates have been produced since flotation was introduced in the area in 1927. An acid recovery plant was operated for about 20 years after World War I, but it has been dismantled, and no recovery of the iron sulphides in the ores of the district is being made at the present time. In June 1950 there were three companies operating mines and mills, Tri-State Zinc Co., Calumet & Hecla Consolidated Copper Co., and Eagle Picher Mining and Smelting Co. The Vinegar Hill Zinc Co. had completed a shaft at a new orebody and had started to develop the mine which will supply the Cuba City mill. The Cuba Mining Co. was holding the Andrews Mine inactive. The Dodgeville Mining Co. was not operating but was exploring for additional reserves. Several small mines were selling ore to the Eagle Picher mill. A general area map is given in Fig. 1. The Eagle Picher Mining and Smelting Co. entered the area in 1946 with an active exploration campaign. Leases on a block basis were secured for the area south from the Wisconsin-Illinois line near

Jan 1, 1953

By Howard N. Eavenson

Waste of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. Average Recovery The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered—it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed 'that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed—often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal—is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1947

By Alan Stanley

THE Maclntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.1 Pigment plant production demands that the MacIntyre mill produce a 44.7 pct. TiO2 ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the Maclntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from one level to the next.. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the, physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO2 has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO2 has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the Maclntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO2 was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiO2 a constant gravity would invariably be obtained, and as the TiO2 value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct TiO2 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO2 value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO2 and as the specific gravity increased the trend was for the TiO2 assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. [ ] Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1952

By A. S. Yue

Small-angle tilt boundaries have been observed in a lamellar eutectic structure. These boundaries are morphologically similar to a theoretical till boundary originally proposed by Burgers. The production of a small-angle tilt boundary in the lamellar eutectic structure is attributed to the formation of an indentation on a planar solid-liquid interface during growth. Constitutional supercooling due to the accumulation of impurity atoms ahead of the interface is primarily responsible for the generation of an indentation. The distance between two faults of like sign, designated as lamellar fault distance, is calculated by the Burgers equation for small-angle boundaries. It was found that the lamellar fault distance decreases exponentially and the tilt angle increases exponentially with freezing rate. SMALL-ANGLE tilt boundaries have been observed in many crystals in the as-grown states by etching techniques. However, a detailed substantial proof for revealing the presence of dislocations in the form of etch-pits was recently accomplished by Vogel. These boundaries are described as an array of dislocations of like sign. The angle of tilt associated with a boundary is treated theoretically by Burgers3 and is given by 0 = b/D for small tilt-angle where b is the Burgers vector of the dislocations and D is their average spacing. During the course of experimentation on the solidi fication of the lamellar Mg-32 wt pct Al eutectic a microstructure which was strikingly similar to a dislocation tilt boundary was observed. An example of the type of microstructure is given in Fig. 1, which shows a combination of transverse and top sections of the lamellar eutectic structure. The lamellae of the top section on one side of the apparent tilt angle are not parallel with those on the other side. Consequently, some lamellae must be terminated somewhere. Fig. 1 shows that the termination of lamellae is analogous to a dislocation tilt boundary in a crystal lattice originally proposed by Burgers. This work represents a closer look at such structures. The factors governing the production of the small-angle tilt boundary are discussed in terms of the freezing condition and impurity distribution in the melt. The effect of freezing rate on the distance between two faults, designated as lamellar fault distance, and the tilt angle is also described. In addition, the lamellar fault distance is determined by means of the Burgers equation for small-angle tilt boundary. EXPERIMENTAL PROCEDURE The slightly impure Mg-32 wt pct Al eutectic rods, 5/8 in. in diam and 12 in. long, were made from 99.99 wt pct Al and 99.98 wt pct Mg and were cast in a high-purity graphite mold. Some of these rods were purified by zone-refining the eutectic using direct-radiation helical-coil furnaces5 A molten zone about 2 in. long was passed through the cast rods at a speed of 5.3 x 104 cm per sec for ten passes of the molten zone. Before the freezing experiment was begun, 2-1/2 in. of the material from the head and tail ends of the zone-refined eutectic were removed from the rod to eliminate any impurity. The freezing experiments were carried out under controlled conditions,8 using a protective atmosphere of purified argon. At the end of each run, observation of the tilt boundary was made throughout the entire length of the rod with a light microscope on the top, longitudinal, and transverse sections (three mutually perpendicular sections) of the lamellar eutectic solid. The experimental data used for the determination of interlamellar spacing and tilt angle were taken from the middle portion of

Jan 1, 1964

By C. O. Dale, W. J. Rundle

THE upper Mississippi Valley zinc-lead area was the first major lead-producing section in the United States. The lead ore, found near the surface in crevices, was relatively pure galena that could be smelted directly into lead, at first in log hearth furnaces and later in more efficient blast type furnaces. French Canadian fur traders encouraged the Indians to mine the lead ore and showed them how to smelt it into lead that had a high value for bullets1 Nicholas Perrot found lead ore on the Mississippi River bluffs near the junction of Wisconsin and Illinois and in 1690 established a trading post on the Wisconsin side of the river opposite the present site of Dubuque, Iowa.2 Shortly after 1720 discovery of Mine La Mott in Missouri diverted considerable attention from the Upper Mississippi area. Mining continued on a desultory basis with operations concentrated in the Galena, Illinois-Dubuque, area. In 1740 at least 20 miners were at work in the Fever River area around Galena and are reported to have shipped 2500 70-lb pigs of lead to Kaskaskia in 1741." Julien Dubuque established a mining and smelting operation in 1790 near the city that bears his name and was granted sole right to exploit the mining operations on the lands of the Sauk and the Fox Indians. He is reported to have produced 30,000 70-lb pigs of lead in 1805. Following the death of Dubuque in 1810 the Indians refused to let the white miners enter their lands, and little was done on the Iowa side of the river until the Indians were removed by treaty with the United States government in 1832." Early mining was entirely for lead but as the crevices were followed down, increasing percentages of zinc sulphide and zinc carbonate were encountered and at first discarded. Later a market became available for the zinc ores, and hand jigging devices were made to separate the lead, the zinc, and the rock or waste materials. The first record of zinc production from the area is for 1860. Production of zinc passed that of lead before 1900, reached a peak of 64,000 short tons in 1917, fell off rapidly and continually to about 2000 short tons in 1938, and since 1940 has ranged from 11,000 to 19,000 short tons. Lead has been of considerably less importance since 1900, and at present only about 10 pct as much lead as zinc is produced. Practically all of the zinc ore has come from orebodies that are rather flat and wide with considerable length as compared to width. Most of the early lead came from the crevice type deposit, but present production is from the predominately flat zinc orebodies. The Graham-Snyder orebody, scene of Eagle Picher operations, is practically all zinc with little or no lead being recovered. Marcasite, present in varying amounts, makes production of finished concentrates by gravity separation impractical. Satisfactory lead and zinc concentrates have been produced since flotation was introduced in the area in 1927. An acid recovery plant was operated for about 20 years after World War I, but it has been dismantled, and no recovery of the iron sulphides in the ores of the district is being made at the present time. In June 1950 there were three companies operating mines and mills, Tri-State Zinc Co., Calumet & Hecla Consolidated Copper Co., and Eagle Picher Mining and Smelting Co. The Vinegar Hill Zinc Co. had completed a shaft at a new orebody and had started to develop the mine which will supply the Cuba City mill. The Cuba Mining Co. was holding the Andrews Mine inactive. The Dodgeville Mining Co. was not operating but was exploring for additional reserves. Several small mines were selling ore to the Eagle Picher mill. A general area map is given in Fig. 1. The Eagle Picher Mining and Smelting Co. entered the area in 1946 with an active exploration campaign. Leases on a block basis were secured for the area south from the Wisconsin-Illinois line near

Jan 1, 1953

By C. J. Leith

A study of the effect of rock composition, rock structure and degree of weathering on the stability of cut slopes is being sponsored jointly by the U.S. Bureau of Public Roads and the North Carolina Highway Commission. In 58 mountain and piedmont counties of North Carolina the percentage of failed cut slopes is greatest in micaceous metasediments, gneisses, and schists, and in saprolite and soil derived from these rock types. Soil slope failures outnumber rock slope failures by two to one. Joints and similar planes of separation exert a strong influence on size and shape of the sliding mass. They may or may not act as failure surfaces, depending on their orientation with respect to the active forces. Climatological data, though indicative of weathering conditions, do not correlate well with slope failure frequency. Because of the presence of joints and similar planes of weakness in soil and rock materials, conventional methods for analyzing slope stabilities are not directly applicable. Empirically derived modifications of these methods are being investigated. A study of the stability of highway cut slopes, sponsored by the U. S. Bureau of Public Roads and the North Carolina State Highway Commission, began in 1962 at North Carolina State of the University of North Carolina at Raleigh. As part of this study all slides, rockfalls and other types of cut slope failures on Federal and State highways in the 58 mountain and piedmont counties in North Carolina were located and described, and the data catalogued in a punched card file system. A major objective of the project is to relate slope failures to properties and physical conditions of the geological units in which the slopes were constructed, and to correlate soil type and/or geological unit with type and frequency of slope failure. The complexities of the problem of slope stability and the limitations which these complexities impose on methods for analyzing slopes have been recognized for many years. A great variety of factors and processes may lead to slides, often making it almost impossible to analyze theoretically the conditions required for stability of slopes. One of the principal factors determining maximum safe slopes is the shear strength of the material in which the slopes are cut, but unfortunately there are very few data available concerning shear strengths of residual soils. Vargasl tested clay derived from gneiss and granite in southern Brazil; the properties of decomposed granite occurring near Hong Kong were determined by Lumb.2 These data are being used, when applicable, to supplement the test data obtained in the present study by Yorke.3 The locations of the North Carolina slope failures, more than 400 in number, are shown on Fig. 1. This map, adapted from the Geological Map of North Carolina,4 suggests the possibility of a relationship between frequency of slide occurrence and rock type. However, the evaluation of this possibility requires consideration not only of the type of rock, but also of its large and small scale structural features, its susceptibility to and degree of weathering, and the composition and structure of the weathering products. Soil slope failures in thoroughly weathered soil material and saprolite outnumber rock slope failures two to one. INFLUENCE OF ROCK TYPE The agricultural soil type involved in each soil slope failure was identified and each failure was catalogued in terms of the parent material from which the soil was derived. These data indicate that most of the slope failures, whether in the rock or in the derived soil, are associated with metamorphic rocks (see Fig. 2a). The data may be skewed somewhat because of the relative sizes of the total areas underlain by the various rock types, but Leith and Gupton5 have demonstrated that the preponderance of failures in metamorphic rocks is of much greater magnitude than could be accounted for by the areal factor alone. The dominance of metamorphic rocks is emphasized when soil slope failures are considered in terms of the specific rock types from which the soils were derived (see Fig. 2b). In particular, mica schists and mica gneisses account for more slides

Jan 1, 1965

By L. C. Brown, A. J. Stewart

Phase transformations have been studied in Ag-Zn alloys quenched from the high-temperature bcc 0 phase and lying in the composition range 37.4 to 50.0 at. pct Zn. On quenching, the alloy with the lowest zinc content transformed to massive a (fcc); all other alloys formed the ordered (3' phase. On deformation, a martensitic reaction took place forming a close-packed structure. At Lou' zinc contents transformation to this structure was complete. However, above 43 at. pct Zn a p.rogressively increasing amount of ß' was retained following deformation. The close-packed structure was fcc at lower zinc contents (under 47 at. pct Zn) and either hcp or a mixture of fcc and hcp at high zinc concentrations. The structures produced by cold working were unstable and on aging transformed to the ß' phase or the complex hexagonal to phase. For low zinc contents (under 43 at. pct) the fcc st-ructure transformed directly to the equilibrium To phase. With higher zinc contents, some 13' was retained following defownation, and on aging the amount of this phase relative to the close-packed structure increased. On further aging both structures transformed cornpletely to PO. Metallographic examination indicated that the nature of the deformation product depended very markedly on the mode of deformation. Tensile deformation gave a microstructure characteristic of thermal martensite. KING and Massalski1 have shown that an alloy of Ag-50 at. pct Zn quenched from the high-temperature bcc ß phase undergoes a low-temperature ordering reaction forming ß' which can be retained to room temperature. On deformation an hcp phase is produced, although this is unstable and the structure reverts completely to ß' on aging. In the present paper, the work of King and Massalski is extended to cover a wide composition range in the p phase, observations being made of the structure of the quenched 13 and of the effects of deformation and aging. The relevant portion of the Ag-Zn phase diagram is shown in Fig. 1. King and Massalski have shown that close to stoichiometry the ß' phase is the equilibrium structure at low temperatures. The approximate composition range of this phase, taken from a recent paper by Pops and Massalski,3 is shown on the phase diagram. The locations of atom sites are very similar in the ß' and to structures, and the 4, structure can be derived from the 0' structure by a small movement of atoms mainly in the direction of the cube diagonal.4'5 However, the probability of filling any particular atom site by a silver or a zinc atom is markedly different in the two structures. The structure can be considered partly ordered but the arrangement of the ordered atoms is completely different from that in the p' structure and transformation from ß' to requires a large fraction of the atoms to change position. It has been shown that the ß' transformation is thermally activated involving normal nucleation and growth processes.5,8 Massalski and Barrett7 have shown that in the Cu-Zn binary the (3 phase can be retained in the ordered state to room temperature over a wide composition range. On deformation a new close-packed phase is produced, the structure varying from fcc to a mixture of fcc + hcp to hcp alone with increasing zinc concentration. It appears that an ordering reaction is necessary to retain the bcc phase to room temperature. In CU-Ga,8 the bcc phase cannot be retained to low temperatures as it transforms by a massive reaction above the ordering temperature of the ß phase. The structure of the massive phase is very similar to that in Cu-Zn, varying from fcc to fcc + hcp to hcp with increasing zinc concentration. Similar structures have also been observed in CU-A1,9 Ag-Cd,10,11 and Ag-Al.12 EXPERIMENTAL The alloys were prepared by melting fine silver (99.99 pct purity) and electrolytic zinc (99.999 pct

Jan 1, 1969

By W. M. Myers

Certain minerals possess inherent color and other properties that make them suitable for the pigmentation of paints, mortar, plaster, concrete, face brick, and other materials. Their production is one of the most ancient of mineral industries and their use by primitive man is well known. These natural pigments have some economic factors in their favor, particularly wide geographic distribution, low cost of production, ease of preparation, chemical stability, and permanence in use so that they continue to form the basis of a small but useful industry. When used in paints such pigments act as a filler and supply body and opacity in addition to color. Natural mineral pigments are prepared for the market by the comparatively simple operations of washing, grinding, blending, and calcining. Any one, or all of these processes may be applied to a single pigment. The development of synthetic pigments and the use of byproduct materials have introduced competition with the products of nature and are having a growing influence on the economic position of the mined minerals. Development of the Industry The industry developed to commercial stature in Pennsylvania largely because of the presence of beds of ocher extending from Easton in a southwesterly direction toward Reading, and a variety of small iron mines in the region. The mining of paint ores in the Lehigh Valley was active as early as 1850 and shortly after the Civil War the establishment of mills expanded production and led to the development of new products and eventually the manufacture of synthetic pigments. Pennsylvania continues to maintain it.s leadership as a producer of mineral colors. Production is recorded also in New Jersey, Illinois, Virginia, Ohio, and Georgia. Iron as a Pigment Iron in various compounds is the most important pigment in nature. The iron pigments are characterized by stability, light fastness, good covering power, high index of refraction, and economy in production. Ferrous compounds display a typical green coloration. This has not been employed as a commercial pigment to any great extent except incidentally in such greenstones as have been used in construction, or crushed and sized for application as a granule to roofing. Ferric oxides are characteristically red and form an important group of industrial pignents. Hydrated ferric oxides exhibit various shades of yellow and are present in such familiar pigments as ocher and sienna. The addition of small amounts of manganese oxide or carbon as organic matter to the yellows produces the brown umbers. Magnetite is one of the few black minerals that grinds to a black powder. The mineral pigments vary from earth colors of low intensity and great dilution of iron content to almost pure iron compounds with high tinting strength and correspondingly greater value. There has been some relationship between the mining of iron ores and the production of mineral pigments; although the production of colors is not carried on appreciably as a byproduct of iron mining. A number of mineral pigment producers, particularly in the eastern states, have operated mines which in the past were small producers of hematite, bog ore, or carbonate ore. The knowledge of the location of the deposit and its possibilities as a producer of pigment are due to its past history as a producer of metallic ore. Many iron compounds may be changed in color by calcination, the end product being Fe2O3, a stable red oxide. The yellow hydrated oxides may be changed to red. The gray carbonate, found in Carbon County, Pa., calcines to a fine red product. Ferrous sulphate (copperas) often available in tonnage as a byproduct of the steel industry, breaks down under heat or chemical action leaving a residual red oxide. Pigments produced by calcination or dissassociation of compounds possess the advantage of fine particle size and ease of grinding. Mineral Pigments MINERAL BLACKS Many black minerals grind to a light colored powder. This characteristic is familiar to the mineralogist as the white streak produced by a black

Jan 1, 1950