Search Documents

By D. W. Fuerstenau

THE object of this article is to point out the experimental relationship which exists among contact angle, adsorption density, zeta potential, and flotation rate data. In each of the experiments discussed in this article, the surface properties of quartz, as a function of pH, were measured in solutions to which constant quantities of dodecylam-monium acetate were added. Morrow1 and deBruyn2 worked with solutions containing 4.08x10-5 moles per liter, whereas Fuerstenau3 and Seele worked with solutions containing exactly 4x105 moles per liter, but this difference is not significant. The pH of the solutions was regulated with HCI or NaOH in all cases. In each case, the addition of collector was constant, but the concentration of dodecylammonium ions decreased because of the formation of dodecylamine at higher pH values.2 Contact Angles: Gaudin and Morrow1 presented data for the contact angle of quartz in solutions containing 4.08x10-5 moles of dodecylammonium acetate per liter between pH 2 and pH 10.15. Using the same captive bubble techniques, the writer measured contact angles on quartz in solutions containing 4x105 moles of dodecylammonium acetate per liter at pH values ranging from 9.9 to 13.2. Both sets of data are presented in Fig. 1, in which the contact angle in degrees is plotted as a function of the pH of the solution. From pH 2 to about 8, the contact angle

Jan 1, 1958

By John T. Crawford

Introduction Loading and hauling systems are evaluated in open pit mining for new properties, expanding existing operations, changing systems or equipment, and equipment replacement analysis. The objective of such evaluations is to determine the equipment needed to handle planned tonnages at the lowest cash flow cost. Cash flow costs are used to combine capital outlays with operating and maintenance costs. Leasing costs could be substituted for capital costs with appropriate modifications to calculation procedures. These modifications will not be covered. This chapter will describe methods of evaluating loading and hauling systems, concentrating on some of the more often raised questions concerning quantitative data. While the methods described are not the only ones in current use, they have a record of proven reliability. The shovel and haulage truck system is used In the examples because of its common use in open pit mines. In medium to large open pit mines, electric shovels and diesel-electric drive haulage trucks are normally used. The basic ideas presented in this chapter apply to all loading and hauling systems, with appropriate modifications. The process of performing a shovel and haulage truck evaluation can be time-consuming and tedious because of the quantity of data involved, but it is not particularly difficult. The examples used to Illustrate shovel and haulage truck evaluation are based on a hypothetical open pit mine operating 350 days per year producing 31 750- 000 t (35,000,000 st, 100,000 stpd) annually, of which 11 110 000 t ( 12,250,000 st, 35,000 stpd) are ore. Selection of the optimum shovel and haulage truck fleets will be shown. The principal sources of data for the examples or any other equipment evaluation are equipment manufacturers and actual operations. Whenever possible, actual operating experience should be used to verify estimates. The quantitative data presented herein are unrelated to a specific existing mining operation.

Jan 1, 1979

By Benjamin Gi ldersleeve

Uniquely colored, thin-bedded quartzite is quarried between Crossville and Crab Orchard in Cumberland County, Tenn. It is produced in all sizes up to the limits of transportation from beds usually ranging in thickness from less than 1/2 in. to 6 in. The stone is very resistant to wear and weathering and is marketed throughout the country for many different purposes in exterior and interior construction. The annual production exceeds 36,000 tons, valued at nearly $1,000,000.

Jan 1, 1950

Abbott, Franklin E. Adgate, Frank Aertsen, G. Aid, Kenneth Albert, H. I. Alexander, D. B. W. Allan, Wm. G. Allen, R. 0. Allen, Roy H. Aller, Mr. and Mrs. F. D. Altmayer, Maurice Ambler, Harry A. Ambrose, A. WV. Ammon, Mark A. Ammon, Mr. and Mrs. Robt. Anderson, George H. Anderson, Mr. and Mrs. L. D. Andros, S. 0. Appleby, W. R. Archer, R. S. Armitage, Paul Arobb, Alden D. Arthur, Walter Ashman, A. 0. Atkinson, R. H. Aupperle, J. A. Austin, D. F. Avery, G. E.

Jan 11, 1919

By Hans Lundberg

N OT so long ago, the discovery of an orebody took place only by accident. At the present time mineral deposits, even though concealed, may be revealed by their physical or geophysical characteristics, considered in connection with geological studies. Geophysical methods are based on sound, scientific principles and in no sense partake of the mysteries of "divining-rod " methods. Geophysical methods are divided into two main groups: Group I: Methods where fields of force surrounding mineral deposits are investigated (magnetic, gravitometric, electric) ; Group I1 : Methods where fields of force are applied (produced) and anomalies caused in these fields by mineral deposits are recorded (electric, seismic). By methods belonging to Group I, the investigation of the fields of force may be brought to an astonishing degree of accuracy by means of highly sensitive and delicate apparatus (torsion and magnetic balances) ; at least, in simple cases these methods have proved to be of great value.

Jan 1, 1925

Truman H. Aldrich '78 W. S. Ayres '73 Andrew A. Blair '75 Walter M. Brodie '72 H. M. Chance '74 Fred'k G. Corning '77 Ralph Crooker '81 A. W. Crookston '80 George M. Davidson '81 W. B. Devereaux '80 H. S. Drinker Founder

Jan 1, 1929

By AIME AIME

THE following Officers, Directors, and guests were present: Herbert Hoover, A. R. Ledoux, Henry S. Drinker, Edwin Ludlow, Samuel A. Taylor, Charles F: Rand, William M. Corse, Arthur S.. Dwight, Glen H. Clevenger, L. W. Francis, F. G. Cottrell, Bradley Stoughton, Percy E. Barbour, E. P. Mathewson, Dorsey A. Lyon, Archibald Douglas, A. D. Flinn, RobertLinton, James F. Kemp, William Y. Westervelt, J. W. Richards, W. L. Saunders, George Otis Smith, Thomas T. Read, J..C. Murray, Ralph Arnold. A Committee on Mine Equipment was appointed composed as follows: Graham Bright, chairman, William Kelly, Howard N. Eavenson, R. E. Hobart, and S. P. Rumsey. B. D. Saklatwalla was added to the Committee on Miscellaneous Metals and W. Spencer Hutchinson was added to the Committee on Mining Geology. A revised budget for 1921 was approved. A petition duly signed to amend Section 1., of Article III of the Constitution, increasing the initiation fees from ten dollars to twenty dollars, was approved by the Board.

Jan 1, 1920

By E. V. Daveler, Frank L. Antisell

CERTAIN physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface, and the "set," or the decail appearance of the surface of the shape. The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are these characteristics connected that they are often used as synonymous terms by the refiner when he is speaking of well-refined copper. Oxygen is often spoken of as a medicine for copper, it being used to regulate the pitch.

Jan 1, 1920

Members whose deaths were reported from Mar. 5, 1919, to Apr. 5, 1920. Elected Died 1895 ANDERSON, ROBERT HAY 1920 1916 ATWATER, M. W 1919 1905 BARD, D. C 1920 1893 BECKER, GEORGE F 1919 1914 BIGELOW, BRAXTON 1917 1917 BLACK, HERBERT F 1919 1911 BOWLER, ROBERT P 1919 1902 BROWN, ARTHUR H 1919 1913 BURNHAM, WILLIAM 1918 1905 Carnegie, Andrew 1919 1900 CARPENTER ROLLA C 1919 1908 CONNER H. MCKEAN 1919 1883 COOK, ROBERT A 1919 1903 COOPER, JOHN 1919 1875 CROXTON, SAMUEL W 1919 1889 DICKMAN, R. N 1919 1893 DUFOURCQ, EDWARD L 1919 1917 FAY, CHARLES H 1918 1875 FOHR, FRANZ 1919 1879 FRICK, H. C 1919 1880 GAYLEY, JAMES 1920 1917 GARVIN, JOHN C 1920 1915 GIBBS, CHARLES H 1919 1917 GODBE, RALPH T - 1918 GREGORY, A. E 1919 1917 HAMILTON, A. McL 1918 1914 HEISE, HENRY C - 1913 HINCKLEY, E. R 1918 1884 JENNINGS, HENNEN 1920 1895 JOHNSON, J. E., JR 1919 1895 KANN, MEYER M 1919 1895 KAYSER, H. W. F 1919 1918 KENNEDY, DANIEL J 1903 KING, PAUL S 1919 1901 LANGTON, JOHN 1920

Jan 1, 1923

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period May 10, 1916 to June 10, 1916: G. Aertsen, Philadelphia, Pa. Hennen Jennings, Washington, D. C. Frederick C. Alsdorf, Wickenburg, Ariz. H. M. LaFollette, LaFollette, Tenn. A. H. Anderson, Worcester, Mass. E. T. Lednum, Chicago, Ill. J. H. Batcheller, Mattapoisett, Mass. Francis Church Lincoln, Reno, Nev. Arthur B. Clark, Sheridan, Mont. H. Mortimer-Lamb, Montreal, Canada. J. Murray Clark, Toronto, Canada. Andrew W. Newberry, San Francisco, Cal. J. H. Collier, Oakland, Cal. C. E. Pettibone, Cleveland, 0. H. S. Emlaw, Spring Lake, Mich. Heinrich Ries, Ithaca, N. Y. E. L. Estabrook, Platteville, Wis. C. S. Robinson, Youngstown, 0. James W. Hambleton, El Paso, Tex. - M. K. Rodgers, Basin, Mont. James Henderson, London, England. E. J. Rossbach, St. Louis, Mo. G. P. Hulst, East Chicago, Ind. J. B. Tyrrell, Toronto, Canada. William F. Jahn, Riebeling, Mont. G. B. Waterhouse, Buffalo, N. Y.

Jan 7, 1916

By ROBERT. RICHARDS

I. INTRODUCTION The object of this paper is to enlarge the field of settling velocities treated by me in my former papers, Close Sizing Before Jigging, and Sorting Before Sizing.' There seemed need of work both on coarser and on finer sizes. Messrs. A. Sidney Warren and M. L. Nagel undertook the investigation for the coarser sizes, from 12.85 mm. down to 2.05 mm. diameter. Their work, because of the closer spacing and because of the increased number of observations and consequent stronger averages, called for a revision of the former work. Messrs. G., A. Barnaby and Ralph Hayden undertook this part of the work, from 2.49 mm. down to 0.28 mm., which is near the limit of sifting. Their work covers the ground much more minutely and comprehensively than the former papers. There remained to be covered the portion of the field too fine for investigation with the sieves. This part, covering the range of grains from 0.48 to 0.03 mm., was undertaken by Mr. E. S. Bardwell. For it he used the elutriation method. II. THE FIRST, OR COARSEST, SECTION OF THE FIELD. The first desideratum in this investigation was a series of sieves for sizing the sands preparatory to making the tests. It became necessary, therefore, to decide on a sieve-scale for this purpose. A sieve-scale is a series of sieves in which the dimensions of the holes of the successive members form a series increasing by a. definite ratio. There are three natural sieve-scales : 1, progressing by doubling the width of the hole for each suc-

May 1, 1907

By Joseph Hyde Pratt, Douglas B. Sterrett, CHAPEL HILL

I. DESCRIPTION. MONAZITE is one of the minerals which, for a long time, was considered rather rare in its occurrence, but, upon a commercial demand arising for it, prospectors and engineers soon located large deposits of it in the Carolinas and Brazil, and the supply has always been able to meet the demand. During 1908 further sources of supply of monazite have been discovered and developed in Idaho. North and South Carolina, however, are the only States that have thus far put any monazite on the market. Monazite is essentially an anhydrous phosphate of the rare-earth metals, cerium, lanthanum, and didymium (Ce, La, Di)PO;. There is nearly always present a varying but small percentage of thoria, ThO2, and silicic acid, SiO, which are very probably united in the form of a thorium silicate, ThSiO4 Some monazites contain but a fraction of a per cent. of thoria, while others have been recorded that showed the presence of from 18 to 32 per cent. ; but the majority contain from 3 to 9 per cent. of this oxide. It is the presence of the thorium oxide that gives the monazite its commercial value. The analysis occasionally shows also the presence of other constituents, as the yttrium and erbium oxides, zirconia, alumina, magnesia, lime, iron oxides, manganese oxide, and titanium oxide. Monazite is light-yellow, honey-yellow, reddish-, brownish-, or greenish-yellow in color, with a resinous to vitreous luster, and is translucent to subtransparent. It is brittle, with a conchoidal to uneven fracture, and is from 5 to 5.5 in hardness, and from 4.64 to 5.3 in specific gravity. It crystallizes in the monoclinic system, and some crystals have been observed that were 6 in. in length. The more perfect crystals are, however,

Jun 1, 1909

By D. T. Camp, J. A. Clum

WITH experience, the indexing of back-reflection Laue patterns for cubic crystals is usually a straightforward matter. However, for noncubic systems where in general tables of interplanar angles are not available or when inexperienced personnel are involved, properly indexing a crystal is normally a tedious, time-consuming affair. The authors have written a digital-computer program which calculates and prints out a table of interplanar angles for an arbitrary crystal structure and then systematically searches through this table attempting to obtain a consistent fit to back-reflection Laue data supplied by the user. Of course it is possible simply to calculate a desired set of interplanar angles should this be the only requirement. The program was originally written in ALGOL for use on a Control Data G-21 computer and a preliminary version is described elsewhere.' A version in FORTRAN TV which has been run on an IBM 7040 and one in FORTRAN II run on an IBM 1620 are also available. While it is not the purpose of this communication to describe the program in detail, an indication of how the program operates may help one to decide whether the program would be useful under particular circumstances. The hypothetical example chosen involves the indexing of the zinc crystal which has a hexagonal structure and a c/a ratio of 1.856. Input data for this example consists of only nine cards: The first card controls the list of families of planes to be considered. If the Miller indices of a prospective family are (h k 1), the first digit places a limit, in this case 3, on the absolute values of any individual index. The second digit limits the sum (h +k + l + 1), in this case to 5. Therefore the families (013) and (112) are considered but the family (122) is not. All systems, including the hexagonal, are treated using three-digit Miller indices. The second card contains the crystallographic parameters required to define the system. The first digit is 0 if the system is rectangular, that is all angles are 90 deg. If the system is nonrectangular, as in this example, the digit 1 so indicates. The next three values are the lengths of the sides of the reference cell, a, b, c. The final three entries on the card are the angles, a, 8, y between the sides. The digit 0 on the third card indicates that more data follows, the digit 6 shows that a set of six planes is to be indexed, and the value 2.0 indicates that agreement between a tabulated angle and an input angle is considered adequate if their absolute difference is less than 2 deg. The fourth card lists the measured input angles. a12 = 38 deg, a13 = 24 deg, and so forth. More input angles are listed on cards five to eight with the latter giving the input angle 058 = 40 deg. The final card in this series indicates by the digit 1 that no more data is to be processed. The program operates in the following manner: 1) The input data from cards 1 and 2 is read, thereby indicating the crystal system to be examined and the crystallographic parameters of the particular crystal to be indexed. 2) A table of interplanar angles is generated. 3) The input angles contained on cards 4 to 8 are read. 4) The measured input data is systematically compared with the generated table of standard angles. All combinations of poles whose interplanar angles compare with the requisite, specified accuracy are printed out. If no adequate fit is found an indication of this is printed. A typical line from the generated table of interplanar angles is: (001) - (111) 74.92 64.99 It can be shown that in the Miller-Bravais system the first value corresponds to the angles between (0001)-(1121) and the second to that between (0001)-(1011). This particular set of data gave the following result for the planes 1 to 6: (011) (110) (121) (111) (112) (010) The ALGOL version also has the option of simply providing the Greninger-chart coordinates ? and 6

Jan 1, 1967

By J. W. Downey, J. B. Darby, L. J. Norton

THE only previous investigation of the phase equilibria in the Ta-Pd system was reported by Greenfield and Beck.1 Their work (actually a portion of a much broader survey) was limited to the composition range 50 to 75 at. pct Ta and to a single temperature, 1000°C. The results indicated that no intermediate phases were present at this temperature. They pointed out that this was an unexpected result in view of the fact that niobium, which belongs to the same group in the periodic table as tantalum and has essentially the same atomic size, forms a o phase with palladium.' Also, tantalum in combination with rhodium,' iridium,' or platinum' stabilizes the s phase. By analogy, the Ta-Pd system would also be expected to contain a s phase. The present investigation was therefore undertaken to explore more fully the phase relationships in this system. Alloys were prepared by arc melting on a water-cooled copper hearth in an argon-helium atmosphere. The purity of the starting materials was greater than 99.9 pct. The weight losses on melting were less than 1 pct and therefore the alloys were not analyzed chemically. Specimens were wrapped in molybdenum foil, encapsulated in quartz capsules under a vacuum of at least 1 x 10-5 mm of Hg, annealed as indicated in Table I, and water quenched. Optical and X-ray metallography were used for identifying the phases present in the annealed and quenched alloys. The alloys were resistant to attack by several acids; however, a sodium cyanide electroetch and an immersion etch containing 1 part HF, 1 part HNO3, 2 parts H2SO4, and 5 parts H2O by volume were found satisfactory. The X-ray diffraction patterns were taken with a Straumanis-type Debye-Scherrer camera and filtered copper or chromium radiation. A summary of the phases found in this investigation is presented in Table I. No attempt was made to determine the composition limits of the various phases. The present results indicate that this system consists of two terminal solid solutions separated by at least four intermediate phases at the approximate compositions Ta3Pd, -TaPd, TaPd,, and TaPd3. The Ta-rich solid solution, containing less than 10 at. pct Pd at 1150°C, is in equilibrium with a o phase which is stable in the vicinity of 25 at. pct Pd. The latter phase is also in equilibrium with a bct phase at the equiatomic composition. At high temperatures it appears that the Pd-rich solid solution extends to at least 66.6 at. pct Pd and is in equilibrium with the bct phase. When annealed at 900°C, a sample containing 66.6 at. pct Pd transformed to an unidentified phase designated as X. An X-ray diffraction pattern of this phase contained sharp low-angle lines while the high-angle lines were characteristically diffuse. The observed d-spacings and relative intensities for lines in the low-angle region are presented in Table 11. In the vicinity of 70 at. pct Pd an intermediate phase having the TiA13-type structure is formed. It is stable to at least 1100°C, and presumably dissolves congruently into the ter-

Jan 1, 1963

By S. C. Sun

Most previous work on sedimentation of coal 1 and mineral 2-3 suspensions has been conducted in graduated 1-liter glass cylinders of 6-cm diam. With this type of large container it is often difficult to see through the suspension and tedious to perform a large number of tests. Furthermore, the heavy glass walls and the graduation lines of glass cylinders cause internal and stray reflections, respectively. To obviate these difficulties, an Atlab Emulsion Viewer from Arthur H. Thomas Co. was adopted as an alternative apparatus. Equipment: The viewer," shown in Fig. 1, consists of: 1) a stainless steel frame rack holding 21 flat-bottom Nessler tubes or an ungraduated replica 1.64 cm ID and 1.80 cm OD, 2) a movable masked 150-w lumaline lamp behind the tubes, and 3) a scaled glass panel with 100 vertical divisions in front of the tubes. The tubes are snugly held by springs in slots formed by spacer bars, which also serve as shields to eliminate stray light. The lumaline lamp is mounted behind a slit in a movable housing so that it can be positioned behind the suspension to be examined. The lowest or 100-divi-sion line on the front glass plate is leveled with the upper side of the bottom of all tubes. The scaled portion of each tube, roughly 19 cm high and 40 ml in volume, is used to study coal and mineral suspensions. Procedure: The following procedure was used in many tests. A 1.6-gm sample of dry coal was mixed with 16 ml of distilled water in an ordinary test tube and allowed to stand for three days, with occasional shaking to insure thorough wetting of all particles. The slurry was transferred to a Nessler tube and diluted to 32 ml. The pH regulator and flocculating reagent were added, and the slurry was diluted to reach the uppermost or zero-division line. The tube was immediately stoppered and inverted downward and up again ten times during a period of 35 to 40 sec. The lumaline lamp was turned on during the inversion period. After inversion the tube was quickly returned to the viewer rack. The time elapsed for each 10-division drop of the demarcation line between solid and liquid was recorded by stopwatch until the 80-division line was reached in the zone of compression. Additional readings were taken at 15, 30, and 60 min after settling began. The clarity of the supernatent liquid was observed also. As the settling rate became considerably slower at the 75-division line, it was convenient at this time to start the next test in a separate Nessler tube. This was continued until the suspensions in any number of the 21 tubes were tested. An attempt was made to correlate the experimental results between the Nessler tube and a 1-liter glass cylinder. Table I shows that coal particles settle much faster in the cylinder than in the tube, which has a large wall effect.' The correction factor for the tube impedance is 1.662 2 0.145 at the 40-division line in the hindered settling zone, and 1.614 & 0.139 at the 75-division line in the compression zone. This rough correlation was established by dividing the pulp height of each container into 100 divisions and comparing the settling rates of the two containers at the same divisions. Tests were also performed to determine the accuracy of the viewer. The results, not presented, showed that error was within 10 pct.

Jan 1, 1960

By T. E. Evans, C. T. Baroch

ZrB2 was produced in batches of 4 to 6 Ib by interaction of ZrO2, B4C, B203, and carbon at around 2000°C in a simple graphite resistance furnace. Techniques of production are discussed and the final design of a suitable furnace is described in detail. Several other borides were made by the same technique and the process appears to have possibilities for commercial production. N seeking out new hard and refractory com- pounds, many researchers have turned to the investigation of the borides and excellent papers have been published on the properties of these compounds. Few papers, however, have appeared on the techniques and problems concerned with the production of these high temperature substances. This report describes progress made in developing a method for preparing zirconium diboride, ZrB2, on a pilot plant scale. The literature of the borides and other refractory hard metals recently has been reviewed, annotated, and classified so completely' that it is needless to attempt such an outline here. It is enough to say that three borides of zirconium have been reported: ZrB, ZrB2, and ZrB12.2 ZrB2 is the most stable of these and is especially stable in the presence of carbon up to and including its melting point of around 3000°C. Like most borides, it can be prepared in several ways. It can be prepared by synthesis of the elements, but these are expensive and difficult to produce in a high state of purity. Obviously, production directly from the oxides would have decided economic advantages. In electrolytic production such as that of calcium boride,:' the product is recovered as a sludge mixed with electrolyte; and separation of product from adhering electrolyte and regeneration of the electrolyte is an involved and difficult process. The work on borides was started on a small scale in 1948. Late in 1949, Naval Ordnance expressed a specific interest in ZrB2 and the project then centered on this compound. After the usual experimental work necessary in a new field, ZrB2 of good quality was produced by heating mixtures of B4C, ZrO2, B2O3, and carbon to a temperature of about 2000 °C in a resistance-type electric furnace. Over 100 lb was made for experimental use tests, and the method of production probably could be expanded into a commercial operation. A similar process has been described by Kieffer and coworkers.' The main chemical problems were the development of proper charges to insure complete reduction of the elements, determination of the proper temperature range at which these reductions took place, and adoption of techniques necessary to pre- vent inclusion of such impurities as carbon and nitrides. The mechanical problems consisted of developing a simple practical furnace that would attain the high temperatures required and permit use of a controlled atmosphere when necessary and determining of suitable refractories. Both problems were solved by designing a crucible resistance furnace. Crucible Resistance Electric Furnace Attempts were first made to produce ZrB2 in an electric arc furnace, but such a furnace would not provide the degree of carbon control required for producing clean graphite-free borides, so it was decided to try working in a crucible. Obviously, the furnace would have to be constructed of graphite, as the temperatures required are too high for other refractories or heating elements. Crucibles were made by hollowing out segments of graphite electrodes, which were fitted with a cover and clamped between two electrodes so that the current passing through the thin wall of the crucible would generate heat, using the principle of the Helberger crucible furnace."? Preliminary tests with this type of furnace were encouraging and led to the furnace design shown in Fig. 1. The essential components were a thin-walled graphite crucible resting on a graphite block, which formed the lower electrode assembly, and a top electrode assembly swung from a pipe column making contact with the top of the crucible. The space around the crucible was filled with graphite prepared from waste electrodes crushed to about ¼ in. This packing had excellent insulating properties, both electrically and thermally, and could be removed easily and quickly from around the crucible by means of an industrial vacuum cleaner. The largest resistor crucibles were machined from 8 in. electrode stock and were 26 in. long, with a side wall Yi in. thick and a 1 in. bottom. Temperatures were determined optically by sighting down a 1 in. hole drilled longitudinally through the top electrode and the crucible cover. Sealing this hole at the top was a water-cooled brass sight-glass assembly, shown in Fig. 2. An opening was provided for a light flow of helium to keep the sight opening clear of smoke, and a glass prism above the sight glass changed the line of sight to the horizontal for easier reading. More recently, the prism and optical pyrometer were replaced by a photoelectric recording pyrometer. At first the charges were placed directly in the resistor crucible but this meant that everything had to be withdrawn from the furnace every time the charge was emptied. Later, smaller crucibles were made up that could be placed inside the resistor

Jan 1, 1956

By J. Armanet

THREE MINING colleges are maintained in France; the École Nationale Supérieure des Mines, of Paris; École Nationale Supérieure des Mines, of Saint Etienne; and the École Supérieure de la Metallurgie et des Mines at Nancy. Besides graduates of these schools, a few graduates of the École Centrale des Arts et MIanufactures and of the École Polytechnique are employed as ]nine managers or engineers; however, most of the latter have taken a graduate course at one of the mining schools.

Jan 1, 1939

CONTENTS PAGE East Texas, except the Gulf Coast-H. Vance 3 Gulf Coast-L. P. Teas 8 Texas Panhandle-C. C. Rae 16 North Central Texas-H. F. Smiley 23 North Louisiana, South Arkansas and Mississippi-B. C. Craft 25 Oklahoma-C. H. Pishny, Raymond M. Carr and E. J. Dickinson 31 Kansas-E. A. Koester 35 Rocky Mountain District-C. D. Johnson 46 Illinois and Indiana-T. Wasson 49 Michigan-T. Wasson 52 Eastern States-P. D. Torrey and W. H. Young, Jr 58 West Texas and New Mexico-W. V. Vietti. Published as a Supplement.

Jan 1, 1933

By Johnson Crawford, Alan H. Hoagland

Zinc mining at Jefferson City began in 1854 with small scale production of oxidized ore from open pits. Significant production began in 1913 with the development of the Mascot Mine by the American Zinc Company. In 1965, four flotation mills were treating crude ore at the rate of about 12,000 tons per day and the Mascot-Jefferson City district currently is the largest zinc producing area in the United States. The producing mines, Mascot, Young, North Friends Station, New Market Zinc, Grasselli, Davis-Bible, Coy, and the Jefferson City, are 15 to 28 miles northeast of Knoxville in the Valley and Ridge physiographic province, an area of gentle relief lying between the more rugged Great Smoky Mountains and the Cumberland escarpment. The ore is strata bound, occurring essentially within a stratigraphic range of 200 feet in the Lower Kingsport and Upper Longview formations of Lower Ordovician age. In the lower strata of the mineralized section, the ore generally is found in coarsely crystalline elastic dolomite breccia containing silica and chert debris within a sequence of aphanitic limestones. The upper strata of the mineralized section are fine-grained primary dolomites that, in the ore zones, have been fragmented in mosaic patterns by solution collapse with the interfragmental space filled by white gangue dolomite and sphalerite. The mineralogy is unusually simple, sphalerite being the only important sulfide. Pyrite is very sparse. Dolomite gangue is abundant, silica was deposited in quite small amounts, calcite is minor, and fluorite and barite are very rare. The principal ore controlling structures are rubble breccia zones that were formed during the post-Lower Ordovician-pre-Middle Ordovician erosion interval by supergene solution as a phase of the development of a regional karst system of underground drainage that extended to' depths of at least 800 feet. The major Appalachian orogenic structures are post-ore and have been superimposed on the ore bodies. There is substantial evidence to support the current thinking of the writers that the ore deposits were formed at a depth not exc1~eding 800 feet.

Jan 1, 1968

By P. A. Beck, M. V. Nevitt

All binary and a number of ternary u alloys formed by first long period transition elements were examined and found to be ferromagnetic at low temperatures. The Curie temperatures for these alloys were measured. It was found that the correlation of the Curie temperature with composition may be described qualitatively in terms of the contributions of the various component atomic moments to the saturation moment of the alloy. Ternary Fe-Cr-Mo u phase alloys were also found to be ferromagnetic, with a Curie temperature dependent on the iron content and largely independent of the unit cell dimensions. Similar relations were found for the Co-Fe-Cr and the Co-Cr-Mo a alloys, where the Co + Fe content appears to determine the Curie temperature. RECENTLY, it has become increasingly evident that the u phase is some kind of an "electron compound." Several papers1-' discussed the empirical correlation between the composition of the various u phases in alloys of the transition elements and the distribution of electrons in the partially filled d-levels of the component atoms. However, a picture of the latter can be formed only in a more or less intuitive manner, as in the Pauling theory," and the rigorous treatment of these problems is at present prevented by lack of adequate knowledge of the electronic structure of the transition elements in the metallic state. It appeared reasonable to expect that investigation of the magnetic properties, which are related to d-shell electrons, may help in clarifying the physical nature of the foregoing empirical correlation. Qualitative tests of samples of various compositions have shown that certain u alloys become ferromagnetic at liquid nitrogen temperature." The present investigation was undertaken to determine whether or not low temperature ferromagnetism is characteristic of a large variety of u alloys and to establish how the Curie temperatures of ferromagnetic u alloys are influenced by changes in composition and in lattice parameter. In the first portion of the in- vestigation, Curie temperatures were measured for a series of u alloys containing either vanadium or chromium with one or two of the elements manganese, iron, cobalt, or nickel. In the second phase of the work, data were obtained on the Curie temperature of ternary (Fe, Co, Cr)a, (Fe, Cr, Mo)a, and (Co, Cr, MO)U alloys, as a function of composition and of interatomic spacing. Experimental Procedures High frequency vacuum melting in high purity re-crystallized alumina crucibles was employed in the preparation of the u alloys, using metals whose lot analyses are given in Table I. Approximately two-thirds of the alloys were analyzed chemically, the analytical results being in acceptable agreement with the intended compositions, as seen in Tables I1 and 111. The specimens were annealed for homogen-ization in an atmosphere of purified 92 pct He and 8 pct H, mixture or in evacuated and sealed Vycor tubes at temperatures from 780" to 1300°C, depending on the temperature range of the u phase field for the particular composition. The annealing temwerature and time for kach alloy are given in Tables 11 and 111. Curie points were determined by an induction method; the change with temperature of mutual inductance between two coils was observed when the i-u specimen was inserted into the flux path between the coils. The transformer consisted of three coils each containing 1200 turns of 0.0050 in. diam enameled copper wire. The center coil, P in Fig. 1, served as the primary coil, and was linked magnetically with each of the two secondary coils, S, and S? which were connected in series opposition. The primary coil, P, was energized by an audio-oscillator, set at a frequency of 500 cycles per sec, while the signal from the transformer secondary circuit,

Jan 1, 1956