Search Documents

By P. H. Mell

AMONG the minerals exhibited at the Atlanta Exhibition of 1881, soapstone, kaolin, and asbestos were well represented. The first two occur in large quantities, of very pure quality, throughout the South. The last is somewhat limited in amount, yet in certain localities it exists in masses sufficiently large to pay for working; in North Carolina, Georgia, and Alabama it has been mined with some profit. I would, in this paper, call special attention to the minerals soapstone and kaolin, because their many valuable qualities seem to have been al most entirely overlooked by our Southern manufacturers. Steatite, particularly, occurs in such large quantities, and generally in such close proximity to the great iron regions of Alabama and Georgia, that it is amazing that the iron companies will persist in sending abroad under. heavy expense for firebrick. It would require a much smaller sum of money to quarry this rock and place it at the various furnaces ; and the results obtained, I am sure, would prove its superiority over the majority of firebrick brought into this region. Soapstone, as well as kaolin, is found throughout the metamorphic regions of Alabama, Georgia, South Carolina, and North Carolina. Below-will be found seven analyses that I have made of this mineral, taken from various points in the four States above mentioned. I have also subjected these same specimens to severe fire-tests, and the results were very satisfactory. The tests were conducted in the following manner: Small portions of the compact variety were carefully weighed and placed in a Fletcher's new crucible furnace for gas, and subjected for half an hour to a heat that will in 12 minutes fuse iron. The only effect upon these specimens was a slight change in color .to a darker shade, a small loss in weight, due evidently to the evaporation of water, and, in one or two specimens, a slight degree of fusion on the sharp edges. The first specimen subjected to investigation was taken from a large outcropping in Tallapoosa County, Alabama. Specific gravity, 2.88 ; hardness, 1.9; color, blue gray. Composition Water, - 2.68 Silica, - 65.46 Iron oxide, - 2.10 Alumina, - 15.02 Magnesia, - 15.35 100.61

Jan 1, 1882

By William Meyer

DURING the seventeen years Fairchild has been making aerial surveys and aerial photographic equipment many changes and improvements have been made in the equipment and in the technique of using it. Aerial photographic operations have, been developed from the crude methods and apparatus of wartime to a science upon which exact engineer-ing calculations can be based. In the early days there was no airplane specially designed to meet aerial photographic requirements. One type of camera was used in all types of operations. Projects were made to conform to the products we could make and deliver. Obviously this entailed definite limitations. We now have airplanes designed specially for aerial photographic operations in accordance with the conditions encountered in actual service experience. We have cameras for every photographic purpose and our laboratory technique and equipment have been developed to the point where it is possible to make contour maps from vertical aerial photographs with contour intervals as close as five feet. Therefore, the selection of equipment now can be made in accordance with the time at our disposal, the justifiable cost, the scale desired, and the general requirements of the client. This does not mean, however, that arbitrary deliveries can be set for aerial photographic products. The factors in each project vary and each job must be considered in accordance with the factors involved. This accounts for the fact that products of aerial surveys may readily vary from $1.25 to $200 a square mile. Sherman M. Fairchild became interested in the design of a radically different aerial camera during the war. At its close he was about ready to demonstrate his design to the War Department. By 1920, he was able to bring out his first completed model. It had a number of radical features, one of which was the first dependable high-speed between-the-lens shutter, which makes for accuracy in aerial photographic work. Another feature was the use of metal throughout, eliminating the wooden parts that had been employed in wartime cameras. Another feature was the interchangeability of parts.

Jan 1, 1936

By R. W. H. Atcherson

BLAST-FURNACE flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers acid more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of flue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained are shown in Table 1.

Jan 2, 1920

By R. J. Murphy, N. J. Grant, J. W. Dowding

A large number of blast furnace slag-metal tests were examined to determine if the manganese reduction could be used as a primary indicator of the degree of oxidation or reduction of the slag and of its desulphurizing power. Slag basicity and temperature were also evaluated. Two laboratory heats were made and sampled prior to reaching equilibrium to check blast furnace data. IN a recent investigation of the factors affecting desulphurization in the blast furnace, is was evident that manganese reduction appeared to parallel the course of desulphurization. Grant, Kalling, and Chipman1 pointed this out in a series of time studies utilizing closely controlled laboratory melts. Fig. 1 is a composite plot of sulphur removal and manganese reduction as a function of time under two slags of different basicity. Manganese reduction appears to approach equilibrium at approximately the same rate as does sulphur. It was also demonstrated that the addition of oxygen to the slag, as manganese oxide, caused a sharp reversal of sulphur from the slag to the metal.' It has been shown that "Excess CaO" was a primary factor in measuring the degree of desulphurization under ideal reducing conditions,1,2 the following reaction being representative of the process: CaO (slag) + S + C (solid) = CaS(slag) + CO (gas) It was also evident that a second reaction could drive the sulphur from the slag into the metal. A suggested reaction was' CaS (slag) + 0 = CaO (slag) + S Any change in the oxidizing power of the system would thus affect both the sulphur and the manganese without causing any change in the calculated basicity of the slag. "Excess CaO," "Excess Base," and other similar basicity values, under such oxidizing conditions, would therefore not be the best measure of desulphurizing power; instead, as was shown by and Chipman" he oxygen content of the slag at low oxygen levels would be the controlling factor. Unfortunately, the extent to which FeO is reduced in the blast furnace makes it difficult to utilize slag FeO as an accurate indicator of the degree of oxidation. By comparison, manganese reduction in the blast furnace proceeds more slowly and is generally only about 40 to 70 pct complete. manganese, which is present in significant amounts and is readily analyzed, offers an opportun-

Jan 1, 1954

By J. F. Crouch

INTRODUCTION Roll front uranium has unique geologic characteristics (L,) which require specialized mining procedures. Roll front uranium occurs in arkosic sandstones with the ore zone typically less than 100 feet in thickness with up to 400 feet of overburden. The areal extent of ore is often a few thousand acres. Within the ore zone, ore grade material occurs in C and S shaped rolls, which are a few feet in width and height but may run laterally for several hundred feet. Since the total mine plan may include mining all ore, a roll front uranium mine may cover a few thousand acres. For both economic and environmental reasons, a roll front deposit is mined as a series of phases or sub-pits (3, 4) as illustrated in Figure 1. A typical sub-pit is 400 to 500 feet across. Sub-pit 1 is stripped initially and the overburden is spoiled on the surface. Depending on haul distance and overburden characteristics, stripping is done with trucks and shovels (or front-end loaders) or scrapers. When ore is encountered in sub-pit 1, mining begins, and the stripping equipment is moved to sub-pit 2, with sub-pit 2 overburden also being spoiled on the surface. When ore is encountered in sub- pit 2, sub-pit 1 mining should ideally be complete so the mining equipment can move to sub-pit 2 and sub-pit 3 overburden can be spoiled in the mined out sub-pit 1 area. Ore is mined selectively in a series of 12 to 24 inch cuts by a 2-1/2 yard backhoe on the basis of radiometric probing. For effective drainage, ditches must be maintained on the boundary of sub-pits, and mining lifts are kept as level as possible, with the orebody slightly elevated as part of general good mining practice. Waste removal in the ore zone is done by self- loading scrapers near the orebodies and by push-pull or push loaded scrapers away from the orebodies. Each self-loading scraper cut is

Jan 1, 1983

By Oliver C. Ralston, James Norman

DIATOMACEOUS earth occurs in deposits widely distributed throughout the nation. The chief producing areas are in the Western States, where many high-grade deposits are known. Eastern deposits of diatomite are unsatisfactory for many purposes either because of impurity or because of the extremely fine particle size. Eastern users of diatomite, on the whole, must pay for transportation of the material from the west coast. The freight rate is necessarily high because of the great bulk of the diatomite. A satisfactory process of purifying the diatomaceous earths of Maryland and Virginia, which are unsuited for wide use only because of impurities, should be of value to eastern users. In the past, benefication of diatomite by wet processes has been limited to classification or sedimentation for the removal of sand from diatoms. Calcination with salt is used to produce a white diatomite when iron is present in the impurities, and small amounts of clay are rendered inactive in the process. No treatment has been developed whereby a large proportion of clay can be removed from a low-grade diatomaceous earth to give a diatomite of very high purity. In August 1937 the Federal Bureau of Mines, in cooperation with Dr. R. C. Williams, of Baltimore, undertook the problem of purifying low-grade Maryland diatomite by Froth flotation. Work was done at the Eastern Experiment Station, College Park. Unless otherwise stated, the crude diatomite used was from the Patuxent River deposits near Dunkirk. This material, consisting of roughly one-third each or clay, quartz sand and diatoms, was representative of the usual low-grade marine diatomite found in the Coastal Plain Miocene beds of Maryland and Virginia and sporadically in other Atlantic coast states. As received, it contained 50 to 60 per cent moisture and probably had been wet since its formation.

Jan 1, 1942

By A. J. Lanza

IN view of the immense amount of attention that silicosis has received in this country in the past few years, it is timely to review the status of the silicosis problem at present. Who gets silicosis? The individual exposed to the inhalation of free silica dust. The effects upon the individual depend upon the amount of silica inhaled or, in other words, the severity of exposure, rather than upon any special variation or susceptibility among those exposed. A considerable amount of study has been given to determine what may be the role of predisposing causes in the development of silicosis. To mention one instance, at the Picher Clinic careful records were kept of all previous illnesses of the men examined as well as abnormalities present at the time of examination. Examinations of over 27,000 miners were made during the years the clinic was conducted under governmental auspices-a very fair sized sample. The general conclusions from all this work were that the incidence of silicosis is not appreciably influenced by racial, structural, or other inherent qualities; it is influenced by acquired defects-particularly as these affect the lungs. That is to say, the average run of human beings respond similarly to similar exposures to silica dust and those whose lungs are already impaired by tuberculosis or other pulmonary disease acquire silicosis more readily than those with healthy lungs. It may well be, and there is some clinical evidence in support, that negroes acquire silicosis more readily than do whites, but the infection factor has not been so carefully studied among negroes exposed to silica as it has among whites. We know that tubercle infection is more prevalent among negroes than among whites. There may be other factors concerned in the development of silicosis in negroes as compared to whites, but there is not available information upon which to base positive statements. INFECTION AND COMPENSATION Our first ideas about silicosis in this country were derived from early studies in the mining industry where the silica exposure was severe and

Jan 1, 1937

By A. B. Kinzel

A PREVIOUS study1 of the relations of impact strength to inclusions showed that the dynamic strength of steel is lowered by the presence of visible counted inclusions, but that other factors comprised in the term "body" have a marked influence. The previous work was carried out on selected steels from a single source, so that the body factor was purposely minimized, but even under these conditions it was found that inclusion counting or the use of the commercial inclusion rating is not satisfactory. The tensile-impact test, however, was indicated as a satisfactory measure of dynamic strength. It was further suggested that the tensile-impact test should be so standardized as to be suitable for use in specifications, and that the hardness factor should be worked out over a sufficient range to admit ready commercial use of the tensile-impact test. In accordance with these suggestions, and in view of the fact that the steels reported in the previous paper were selected and treated so as to have a minimum variation in body, hardness and structure, further work has been performed on a variety of steels which are not limited by these conditions. The word "body" is used here for want of a better term. It is simply a convenient expression which comprises the effect of the various unknown factors that modify the dynamic strength of the steel. Thus at our present state of knowledge, the writers have chosen to consider hardness, structure and counted inclusion content as factors not comprised in the term "body," and such factors as raw materials, process of melting, fabricating, etc. as comprised in the term "body." Numerous grades of steels made in several ways have been taken from different sources and have been heat-treated to varying hardness by normalizing and by quenching and drawing. The results, therefore, may be considered to be generally applicable to current engineering steels. A certain limitation with respect to the hardness at which steel should be

Jan 1, 1931

By Earl Bardwell

IN his paper entitled, Development of Hindered-Settling Apparatus, Dr. Richards has related the history of the development of the hindered-settling classifier and given illustrations of the several types of this apparatus which lie has designed.1 An earlier paper,2 Close Sizing Before Jigging, shows the nature of the hindered-settling phenomenon and the results which it produces. In the first-mentioned paper Dr. Richards describes the method of getting hindered settling and shows the relation that the constriction bears to the classifier. The question of proper ratios between the area of the sorting column and the area of the constriction opening Dr. Richards leaves open, aside from certain statements as to the ratios which have been found to give good results in practice. While working with a hindered-settling classifier of the type now in use at the Boston & Montana Reduction Plant of the Anaconda Copper Mining Co. a number of interesting facts were brought out which have thrown considerable light on the question of proper ratio between the area of the sorting column and the area of the constriction and which will be made the subject of this paper. Free and Hindered Settling. -If a, mineral particle be dropped into a vessel containing still water, the particle will sink in accordance with the laws of free settling in water, which are as follows: 1. Of two grains having the same specific gravity but differing in size, the larger will settle in still water at the greater velocity. 2. Of two grains having the same size but differing in specific gravity, the heavier grain will settle at the greater velocity.

Jan 8, 1913

By Stanley F. French

ELECTRICAL power and distribution for the sulphide ore plant is an addition and extension of the existing power system which has served the oxide reduction plant since its inception in 1914. The power plant is located at Tocopilla on the west coast of Chile, some 90 miles from Chuquicamata. A brief description of this plant and the existing transmission system is necessary to an understanding of the problems involved in the provision for the sulphide plant load. Originally the Tocopilla power plant consisted of four Escher Wyss turbines driving Siemens Schuckert generators, each rated 10,000 kw. At various times, units of 10,000 and 20,000 kw were added, all of which operated at 215 psi and 600°F at throttle. In order to improve the economy of the station, a Topping unit was installed in 1938 together with a high-pressure steam generator of 360,000 lb per hr capacity. This unit is rated at 11,000 kw and was designed for 750 psi, 880°F. The exhaust from this turbine passes to the low pressure station header for operation of part of the low pressure turbines. Total kw generated by the high pressure boiler, topping turbine and associated low pressure turbines totals 33,000 kw and the total station capacity is 113,000 kw. This installation proved one of the most successful of its kind, operating almost continuously. The original plant was of German design and consequently European characteristics were incorporated into the system, the frequency being 50 cycles and voltages of 500, 5000 and 100,000 were used for low, generator, and transmission voltages,

Jan 1, 1952

By Dorsey Hager

THE possibilities of finding new oil pools in Oklahoma and Kansas are far from promising. In 1916, the only new pools of importance were the Franchot pool near Bixby, the Garber, and the Billings pools in Oklahoma, and the Virgil and Utopia fields in Greenwood County, Kansas. In the first 8 months of 1917, a small pool of unknown extent was opened south of the Stone Bluff pool in Oklahoma, and a pool near Casey, Paunee County, Oklahoma. In Eastern Kansas, interest has been. caused by the sinking of new wells near the old Iola pool, but nothing of magnitude has yet been found. The outlook for new pools is far from encouraging, especially as geological surveys have covered all of Oklahoma and Kansas. There are a few areas where geological surveys throw little or no light on the subject, as exposures are poor, but the chances of finding new pools in such areas are slight indeed, if one can judge from the past history of such areas. So far the geologists have based their opinions largely upon the presence or the absence of geologic structure, such as anticlines, domes, and terraces, but some pools will most certainly be found where no surface structure exists, but where local changes in the sand body favor oil accumulations. However, the possibilities of new pools off structure are small, as fully 90 per cent. of the oil pools are on definite structure. In the past, it is estimated that one test in 150 "wild cats" or new tests has brought in a new field. The writer feels safe in asserting that the proportion will decrease still further, so that but one out of 500 new tests may bring in a pay well in a new area. From now on the principal field of work in Oklahoma and in Kansas will consist in developing the present pools. The years 1915, 1916 and 1917 saw the high peak of Oklahoma and Kansas oil production. The Eldorado and the Augusta oil fields present the largest possibilities for continued production in Kansas. These two pools have been scarcely more than one-third developed, and have greater potentialities than any of the present Oklahoma pools. In Oklahoma, pools of magnitude should

Jan 10, 1917

By Walter Miller

The remarkable strides which have been made in recent years in the art of petroleum refining are not fully apparent until we attempt to compare the scientific status of the industry today with the basic conditions existing a decade or so ago. The spotlight has played so strongly on the development of cracking that many of the wonderful steps brought about in other departments have crept upon us unawares. A number of causes have contributed to this highly accelerated rate of progress. Constant effort by both companies and individuals to obtain the honors and prizes rewarding new discoveries has played its usual important part in our industry as in others. Competition has applied its continuous pressure on the refiner to reduce costs and losses and increase the proportionate yields of the higher-valued fractions. Advances in the engineering professions and growth in chemistry and allied sciences have contributed much. But there are other factors which deserve particular mention. The rapid development of the internal combustion engine, with the rigorous quality requirements and large quantity consumption of both fuel and lubricants has been a tremendous influence in adding impetus to natural progress. The teaching of petroleum principles and practices in many of our best universities and technical schools, and the calling into the industry of ever greater numbers of scientifically trained men to supplement the efforts of the practically trained operators, as well as to apply at close hand the fundamentals of science as a life work, has had and is having an incalculable influence. Important Improvements Let us consider briefly some of the most important improvements: First, distillation, which constitutes the greatest single phase of refinery operations, even with cracking excluded; that phase of distillation being handled as an individual subject in this symposium. Today we are distilling crude oil and redistilling by-products at a rate very much faster than was possible with the lesser knowledge of the art which we possessed

Jan 1, 1927

By Eric Jette

IN a recent article,1 the authors reported the results of an X-ray investigation on the range of solid solutions that occurs in the iron-oxygen system in the vicinity of the compound FeO, which frequently is called "Wüstite." The object of that investigation was primarily to study the unusual type of solid solution phenomena involved in this range. Briefly summarized the results were: 1. The NaCl type of lattice found by earlier workers was confirmed. 2. The lattice dimensions decrease rapidly with decrease in iron content. 3. No alloy that was a homogeneous single phase was ever found at compositions beyond 76.80 per cent Fe, while the theoretical iron content of FeO is 77.73 per cent Fe. 4. Measurements of the densities and lattice constants led to the conclusion that the form of substitution was complex, an FeO group being replaced by oxygen. Such a substitution, of course, is equivalent to removing an iron atom (or ion). The ideal unit cell of FeO can be con-sidered as containing four groups of FeO and, thus, when this type of substitution takes place, there remain in the unit cell three FeO groups and an oxygen, or a total of seven atoms with a gross formula of Fe304 instead of the original Fe404. 5. This was the only interpretation that would fit the experimental results and at the same time be consistent with (a) the previously deter-mined fact that the FeO lattice is ionic (i. e., consists of Fe++ and 0= ions) and (b) the chemical fact that as the oxygen content of the substance increases, ferrous iron becomes oxidized to ferric iron. The experimental results of this investigation are included in Fig. 1.

Jan 1, 1933

By Ralph H. Sweetser

IN these days of the almost exclusive use of byproduct coke as the blast-furnace fuel in this country, it may seem out of place, and smacking too much of reminiscing, to say anything about the use of anthracite coal for blast-furnace fuel. Viewed in the light of present day research and of developments in alloy steel, some observations seem appropriate regarding this raw material that played such an important part in the development of the iron and steel industry during 50 years of the past century. The research work of that period, in which the whole iron and steel industry was revolutionized, passing from wrought iron to steel and from charcoal to three new mineral fuels for blast furnaces, was done chiefly in the full-sized plants of that day; and it was done largely by the ironmasters themselves. The laboratory had not become a part of the ironworks, and scientific instruments were lacking around the blast furnaces; "rule o' thumb" and erroneous theories prevailed-and have not yet all been eliminated. The recent interest in meteoric iron in connection with nickel steels and other alloys proves that it is worth while to search for the reasons for excellence and the causes for failures in the metallurgy of bygone days. Turner1 gives the reasons why the blast furnace of Dr. F. W. Geissenhainer on Silver Creek, Schuylkill County, Pennsylvania, about 10 miles northeast of Pottsville, was operated successfully with anthracite2 in August and September, 1836, and why several other attempts failed. It has taken a long time for us to find out that there are great differences in the behavior of anthracites from the several parts of the anthracite region, as well as differences in coking coals from the bituminous fields.

Jan 1, 1935

By D. W. Jessup

ONLY during the past few years, have the old-fashioned methods for treating ores and byproducts progressed to any marked degree. The advent of multiple-hearth roasting, blast roasting, the baghouse, and the Cottrell plant indicate this change. It is the ability to roast and smelt sulfide ores and concentrates that gave this later advance. Further investigations that will solve the problem of efficient handling of flotation concentrates and their attendant ills are of the utmost importance. With future developments, the metallurgist will be able to smelt more economically and to treat still more refractory ores, making the early methods appear small by comparison. GROWTH OF SMELTING Well within the memory of pioneer smeltermen, the ore was charged directly into the blast furnace as it came from the mine;, only the richer, ores were smelted, the lower grade and sulfide ores were undesirable. Matte was, at first, thrown away and only two products) were desired-slag and lead bullion. Scores of the early smelting companies failed because of improper reduction of ores, high costs, short- furnace campaigns, inability to treat sulfide ores, and ores containing-zinc. With the failure of weaker companies, consolidation eliminated many others, until today the field is dominated by a comparatively few organizations, each strong financially. Formerly, a few thousand dollars would erect a small plant, whereas the modern smelter costs over a million dollars. Ore and products to which formerly no attention was paid are now treated with comparative ease and at a good profit. Mechanical improvements have modernized smelting, furnace tonnages show an increase, and metal recoveries have made enormous strides. Even though costs have decreased, they have not dropped in proportion to the improvements, because of the higher wages, greater costs of fluxes and coke, more undesirable ores smelted, etc.

Jan 8, 1925

By T. Prof. Ph. D. Egleston

THE importance of having perfectly pure metals has led me to present to the Institute a record of some of the trials that have been made to obtain these metals, and also to show one of the largest specimens of extremely thin metal plate which has ever been made. The malleability of metals varies generally directly with their purity, and hence it is only with very pure metals that thin sheets can be obtained. The competition among different manufacturers has been so great at times as to lead to expensive and apparently useless experiments in obtaining in the first instance very thin sheets, and afterwards very large and thin sheets of metal, apparently with no other purpose than that of being able to say that they had produced the thinnest or the largest thin sheet that had ever been made. These experiments were at first confined exclusively to iron, their object being to show the great dexterity of manipulation, as well as the purity of the metal manufactured. They have since been extended to almost all metals by electrical action, and have gone far beyond the limits of what was possible with purely mechanical means. The processes which have been used are rolling or hammering, electrical deposition in a vacuum, and lastly, electrical deposition on plates, easily soluble in acids. The first and last of these methods have been known and practiced for a very long time, having been used to make thin sheets of almost all the metals. The other is of quite recent application. In the iron manufacture, the strife to produce these thin sheets was commenced in the year 1865, by the Sligo Iron Works writing to a firm in Birmingham, England, on a sheet of iron containing 270 square centimeters, and weighing only 4.469 grams. For some time this was considered to be the thinnest sheet iron that could be made. T. W. Booker & Co., of Cardiff, England, however, produced a few months afterward, a sheet of the same size, weighing only 4.015 grams. This was succeeded by one rolled by Neville and Everitt, of Llannelly, weighing only 3.174 grams. This was followed by one from Hallam, of Swansea, which was 283 square centimeters in size, and weighed but 2.979 grams; and this by one rolled by R. Wil-

Jan 1, 1879

By W. F. Boericke

NOT the least interesting sights that New York has to offer the visiting mining engineers are the extensive tunnel operations that are being pushed in connection with the subway construction. While a "hard rock" man might feel at home on these jobs, the engineers driving the subway tunnels have necessarily had to encounter some new problems pe-culiar to the largest permanent mining camp in the country. To drive a heading 36 by 18 ft. in hard rock, with a station section to follow 52 by 27 ft. across-and to do it in the midst of a city's traffic-demands engineering skill of a high order. Not the least of the problems overcome by the engineers in charge was to provide adequate ventilation for the men at the face at all times, so that there would be no delay in the work. With a crew of 40 men (32 drill runners and helpers on the machines alone, working two shifts) a hold-up due to inability to get back promptly to the face after shooting would affect costs quickly. AIR VITIATED BY EXHAUST FUMES FROM MOTOR TRUCKS A complication not encountered by metal miners, but which the subway engineers had to meet, was pollution of the air in the tunnels by fumes from the exhaust of the motor trucks used to haul away the broken rock. As shown in the cut, motor trucks were constantly em-ployed to remove the heavy tonnage broken as the tun-nels went ahead, amounting, according to R. J. Van Wagner, chief engineer of the Del Balso Construction Co., to 48 cu. yd. per ft. of tunnel advance. As the length of the tunnel under his management was 900 ft., it was essential for the safety of the men that suffi-cient air be introduced to dilute the poisonous fumes so that no ill effects would be felt for the entire distance that the trucks had to travel. The presence of the ex-haust fumes was especially noticeable on foggy days.

Jan 2, 1928

By H. M. Boylston

METALLIC manganese was first produced in 1773, by Sven Rinmann, a Swedish mineralogist. In 1799 William Reynolds, of Ketley, England, obtained a patent on the use of manganese dioxide in the manufacture of steel, and in 1808 an English patent was granted to John Wilkinson covering the use of manganese ore, or manganiferous ore, as an addition to iron ore in the blast furnace for the production of a superior grade of pig iron. Karsten showed in 1816 that manganese increased the hardness of iron without decreasing its malleability or toughness, while it caused pig iron to be more white in fracture and more fusible. The first practical application of manganese to steel-making, however, is attributed to Josiah Heath who discovered in 1839 (less than 90 years ago) that manganese conferred upon steel the properties of being more easily worked and welded under the hammer. When Bessemer invented the pneumatic process of steel-making which now bears his name he was at first successful because, as it afterward developed, he was using. a Swedish pig iron high in manganese. When his supply of this material ran out, he used a low-manganese pig from English sources and failed signally to produce a steel which could be rolled, while his Swedish licensees were continuing their successful application of his method. And it was not until Robert Mushet, in 1856, suggested the addition of manganese in the form of spiegeleisen to the molten product of the converter that success again came to Bessemer. In 1866, William Siemens patented the use of ferro-manganese as an addition to molten steel to counteract the bad effects of sulfur. It was in 1888, that Robert Hadfield published at some length his account of the effect of manganese as an alloying element in steel and described the unique properties of the now famous Hadfield manganese steel containing about 12 to 14. per cent. manganese and 1.25 per cent. carbon.

Jan 5, 1927

By M. L. Requa

In the fall of 1910, the Nevada Petroleum Co., operating in the Coal-inga field in California, determined to drill a number of wells with rotary tools, in order to prove conclusively the relative value of the rotary as compared with the standard rig. At that time, the rotary was but little known in California and its proposed introduction met with considerable criticism on the part of the operators and quiet opposition among the standard drilling crews. There were few men available who were competent to handle a rotary outfit, and these few had had but little experience in California fields. Machines as then built were much inferior to those now used, being lighter in construction and of a poorer quality of material. The shells encountered at depths between 1,700 and 2,000 ft. seemed to be too hard to permit of successful drilling, and at these depths the rig was changed over to standard tools and by them completed. Because of the heavy depreciation, the time lost in converting from rotary to standard, and the comparatively small profit, it was concluded that unless in the future there was some material improvement in rotary rigs, nothing would be gained by drilling with rotary tools upon this property. Little or no drilling has been done upon the property since that time, but in the meantime a large number of men have been trained in the use of the rotary; in fact, many standard-tool men have abandoned standard drilling and, starting in as roustabouts, have become thoroughly competent rotary operators. The improvements in the machinery have been such as to remove many of the objections and the rotary drilling of to-day is in every way superior to that of 1910. In contrast, a well drilled recently by the Kern Trading & Oil Co., in the east side Coalinga field may be cited. The first 2,500 ft. was drilled in 24 days and it is confidently expected that the water string will be set with a rotary at 3,400 ft.—a record obviously far beyond that made in 1910 by the Nevada Petroleum Co. The records herewith are published with the hope that some one having more recent data will publish them so that comparison may be

Jan 1, 1915

By Robert H. Dickson

Limestone replacement and contact metamorphic orebodies are 80 irregular that sampling and estimating are far less. exact than in more regular types of deposits; both the mineralized masses and the lenses of ore within them are extremely irregular. So much development work is required to find the ore that the expense of blocking out great tonnages is prohibitive; furthermore, the rock near these orebodies is so heavy that drifts or raises cannot be kept open for many years without excessive repairs. As a result, few mines in limestone have more than three years supply of ore in sight. As most of the ore, is developed by stoping— not by drifting, raising, or drilling—estimates of ore developed do not indicate the total amount of ore that may be expected; they simply indicate the relative condition of the mines. But even if they are to do this, they must be made according to a fixed plan, intelligently carried out. The estimates of ore in the Calumet & Arizona Copper mines, Warren District, Ariz., have been of much value to those who plan the mining and development work. This paper describes the methods of sampling and estimating used in these mines. Sampling Samples are taken in various ways and depend on the condition of the working and the purpose for which the sample is to be used. Drifts, crosscuts, and raises are sampled by channels or by taking a grab off each mine car as it is filled. Stopes are usually sampled by drill holes or by taking a representative sample off each mine car; the latter, or chute, sample is by far the best sample. All workings are studied periodically by an engineer, who makes graphic and detail notes of the geologic structure, as shown in Fig. 1. The daily car tally and assay of each particular working is added to the same sheet opposite the material it represents. These sheets make a permanent record, showing the exact boundaries as well as the grade of ore in all workings.

Jan 1, 1925