Search Documents

By R. W. D. Clarke, J. C. Folinsbee

INTRODUCTION This paper deals with a procedure for planning the mining of an orebody for which cross-sections, plans, grade of ore, and a geological estimate of the ore reserve have been prepared. The procedure begins with the preliminary selection of a mining method or methods on which an engineering evaluation will be carried out. The engineering evaluation is described in three parts: Conceptual Studies Engineering Studies Detailed Design An overall planning model is presented, plus an expanded model for the Engineering Study Throughout the discussion of the planning procedure, reference is made to three bulk mining methods, including block caving, sublevel caving, and longhole sublevel stoping, including a summary of the main characteristics of each of these mining methods. The planning model is designed for a longhole sublevel stoping method, but with modification, will apply to other methods. PRELIMINARY SELECTION OF A MINING METHOD To experienced mining engineers, identification of the nominal mining method for a given orebody normally involves a large measure of judgement. The geological data is reviewed to determine the configuration of the orebody, including size, shape, dip, grade, and metal distribution. Geotechnical data is considered, including the competence of the ore and host rock, faults, fracture patterns, groundwater, and the potential for in situ stresses. Geographical data, including the natural and societal conditions, are evaluated for their effect upon the mining method, and finally, economic data, basically defined as the value of the ore in the ground, but more specifically, including grade of mineable ore, distribution of ore grade throughout the orebody, and metallurgical recovery, will have a bearing on the nominal method selected. Preliminary evaluation of these factors will result in the elimination of the obviously inappropriate mining methods, leaving some method or methods for further, more detailed study. Since ore does not occur in simple geometric shapes, the method selected for more detailed study will require some variation to the standard. A few key factors will bear heavily on the selection and provide a basis for the most realistic choice. Geological Data The configuration of an orebody defined by the horizontal and vertical dimensions, the dip and strike, and the possibility of repetitive occurrences will have the major influence on the selection of the mining method. For bulk mining methods, the dip of the orebody should be steep, or the orebody must be thick so that gravity can be utilized to deliver fragmented ore to a central gathering area. Geotechnical Data The geotechnical data will be studied in greater detail when the nominal mining method has been selected and the engineering evaluation is undertaken. However, some basic initial information must be available. The structural strength of the ore and host rock, including the effect on it of faulting, fracturing, and insitu stresses, must be known. Data from exploration drilling and examination of drill core will assist in the preliminary assessment of these factors. Highly fractured ground may suggest a caving method of mining for certain orebody configurations, whereas highly competent or strong ore might indicate that for a similar configuration, longhole sublevel stoping will more likely succeed. Data obtained on groundwater from exploration drilling will be considered to determine if it can be controlled, or if it will represent a long term major expense or a hazard for which no control is possible.

Jan 1, 1981

By John C. Calhoun, Frank T. Bethel

Glass beads have been surface treated with Dri-film to render them oil wet by n-octane to varying degrees, and capillary desaturation curves have been determined by the restored state method. The desaturation curves show a regularity of increasing displacement pressures as the oil wetness increases. This has been used to compute apparent contact angles between n-octane and water on glass. The family of desaturation curves also shows a regular crossover, such that the residual wetting liquid saturation values are in reverse order to the displacement pressures. A semi-logarithmic variation is shown between the apparent contact angle and the residual saturation. The desaturation data are interpreted to mean that the wetting liquid ceases to be a continuous phase within individual pores before the capillary pressure can be raised sufficiently to force out the wetting phase completely. The saturation of wetting liquid at which this break in liquid continuity occurs is higher as the oil wetness decreases. INTRODUCTION The petroleum industry has for some time been using measurements of capillary pressures on porous media for research correlations and engineering calculations. It has been generally recognized that the capillary desaturation curve reflects the character and arrangement of the pores within the media and the distribution of fluids within the pores. Methods have been proposed for computing pore size distributions, tortuosity factors. and relative permeabilities from capillary desaturation data.' There is little doubt that the interactions between porous rocks and their contained fluids resulting from surface forces play a dominant role in determining the magnitude and direction of capillary pressure measurements. There have been attempts to introduce as variables two quantities — inter-facial tension and contact angle — generally used to char- acterize surface forces, but in spile of the wide interest in these quantities as important variables, few definite conclusions have been drawn concerning their qualitative or quantitative significance. INTERFACIAL TENSION The interfacial tension appears in a capillary pressure function given by Leverett for correlating capillary desaturation type curves. Use of the interfacial tension in this function seems to be justified by other experiments reported. Apparently, interfacial tensions have little bearing on wetting phase residual by desaturation. CONTACT ANGLE The contact angle was utilized as a variable by Bartell and co-workers"." in tests on displacement pressures, later recognized as the initial point of capillary desaturation. Although Leverett did not include contact angle in his original formulation of the capillary pressure function, later workers suggested its addition. Few reports are available to show variation of residual liquid with contact angle as a result of capillary desaturation.' The problems attendant to measuring contact angle within a porous medium are great. As a consequence of the lack of a concrete approach to a measurement. the workers in this area of research have adopted the general expression of "wettability" to indicate the relative position of two liquids saturating a porous body. It has been shown that gross measurements on porous systems, including capillary desatura-tions, are sensitive to wettability. Attempts at giving a scale to wettability in terms of contact angle through capillary desaturation curves have been made and these apparently are steps in the right direction. In these attempts presence of many other variables precludes attainment of exactness. Also, as a result of other variables, it has been impossible to correlate changes in apparent contact angle with changes in other physical measurements of the systems in question. The present work is an attempt to eliminate as many variables as possible in measuring capillary desaturations resulting from changes in contact angle within a porous medium.

Jan 1, 1953

By R. Maddi, I. R. Kramer

The delay time for the initiation of slip was studied in single crystals of a brass, aluminum, and ß brass. A delay time for slip was found in ß brass when the specimens were tested below room temperature; however, one was not found for a brass or aluminum. A general theory for the existence of the brittle transition temperature is proposed. A LTHOUGH a considerable amount of effort has A been devoted to the study of the deformation and fracture of single crystals, the vast majority of the work was concerned with static tests or with tests carried out at relatively slow strain rates. The necessity for the study of a possible incubation time for slip becomes apparent when the various theories which have been postulated for the elucidation of the mechanism of slip are considered. The existence of an incubation period would strongly indicate that slip occurs by a process of nucleation and growth; whereas the absence of an incubation would present rather convincing evidence that slip occurs by a cataclysmic process. In addition to shedding light on the process of plastic deformation, an understanding of the early stages of plastic deformation may be helpful in finding an explanation for the brittle behavior of the body-centered metals under certain conditions. It is well known that these metals, such as iron, molybdenum, tungsten, ß brass, etc., will become brittle as the test temperature is lowered or the strain rate is increased. In spite of the fact that this subject has received considerable attention since the turn of the century, no adequate theory exists today which explains the phenomenon. In the ductile temperature range the metal breaks with a "fibrous" fracture after considerable slip has taken place. In the brittle temperature range the metal fails essentially by cleavage on the {loo) planes: however, some plastic flow is always present even in the most brittle fractures. It is possible, as will be explained later, to ascribe this brittle behavior to the length of the incubation time for slip. Clark and Wood,' using polycrystalline metals, showed that a delay time existed for the yield point in mild steels and that the delay time depended upon the applied stress. These authors stated that the delay time was observed only with those materials for which the stress-strain curve showed a definite yield point. In their work only the mild steel specimens exhibited a delay time at the yield point, while the other materials studied-type 302 stainless steel, SAE 4130 normalized steel, SAE 4130 quenched and tempered steel, 24s-T aluminum—did not show a delay time. These authors' in an extension of their work, found that as the temperature was lowered the delay time was increased. It is, then, the purpose of this investigation to measure or to set an upper limit on the delay time for plastic flow in single crystals of a brass, aluminum, and ß brass. The delay time will also be studied as a function of temperature. The incubation time may be measured by determining the length of time the specimen will support a stress without slip occurring when the stress is greater than the static critical resolved shear stress. In order to accomplish these measurements use was made of a pendulum which was so designed that a single crystal specimen could be placed at various positions along its length. When a pendulum is struck by another pendulum of the same length, an elastic wave is transmitted down the bar with the velocity of sound in the material and is reflected from the far end of the bar. The reflected wave then travels back and unloads the stress until it reaches the impacted end of the bar and the two pendulums separate. The length of time that the specimen is subjected to the stress is equal to the time it takes for the stress wave to travel twice the distance from the specimen to the end of the bar. The stress applied to the specimen is governed by the velocity of impact of the two pendulums. The stress at which the specimen first suffers plastic: deformation was determined in these experiments by examining the specimen under the microscope for the first appearance of slip lines and by measuring the residual strain after each impact. In these experiments the critical resolved shear stress was approached from the low stress side and no attempt was made to determine it exactly. To determine it exactly, it would have been necessary to find that stress at which slip would have just started. However, since the stresses were increased in rather small increments the critical stress is believed to be approached rather closely, as will be seen from the experimental results. The critical stress will be taken as the highest stress obtained before the onset of plastic deformation. The stresses

Jan 1, 1953

By Martti E. Maliniemi

The Svappavaara mine is located 47 km southeast of Kiruna C. The ore deposit now being worked, Leveäniemi, belongs to Luossavaara- Kiirunavaara AB (LKAB) and is the company's, and also Sweden's, third biggest mine after Kiirunavaara and Malmberget. The distance by rail to the Norwegian port of Narvik is 214 km and to Lulei on the Gulf of Bothnia 340 km (Fig. 1). The village of Svappavaara has about 800 inhabitants. The climate is arctic in character. The temperature during the months of December to February is about -20º to -35ºC, and the ground is covered by a blanket of snow for about eight months of the year. The brief, intensive summer often arrives with startling speed, bringing both sunshine and warmth. HISTORICAL BACKGROUND Mining operations took place in Svappavaara as far back as 300 years ago. During the period 1655-1684, copper ore was taken from the deposit called Gruvberget in the vicinity of the village. The total production of raw copper was probably about 1,045 tons. During the 18th and 19th centuries, several attempts were made to extract iron ore from the numerous deposits found within the district. These brave attempts, however, were foiled by the high phosphorus contents and the enormous transport difficulties. The present-day mine fields in Leveäniemi were discovered in 1897. At that time, it was difficult to determine the size and value of the deposit because of the thickness of the soil cover (3 to 15 m) and the

Jan 1, 1969

HARD as it is at any time to provide more than three million tons of coal each year for power plants, the task really gets rugged in the wintertime when the fuel freezes solid in the cars. At the Marysville plant of the Detroit Edison Co. the problem of unloading cars of frozen coal was severe because there was an unloader over only one of the two tracks in the coal unloading house. Moving downward by their own weight, with no driving force to aid them, the spuds of this old unloader were unable to break through the crust on a frozen coal car. 20,000 Lb Force To meet this problem, a new mechanical car unloader was installed over No. 2 track and placed in service in December 1947. It is a Kenney type unloader built by Heyl & Patterson, Inc. of Pittsburgh, Pa., a modification of equipment originally designed to unload iron ore cars. The major advantage of this unloader is the force with which it can drive the sharp spade on the end of its ram down through the pockets of a frozen coal car. The unloader consists of the following major units: 1. A traveling bridge structure. 2. A traveling trolley. 3. A retractable and oscillating ram. 4. The operators cab and controls. The bridge is provided with safety hooks to prevent its being lifted from the rails by the upwards push of the ram. The bridge will travel 190 fpm and has sufficient traction on its four wheels to move three loaded 70 ton cars. The trolley runs on tracks supported by the bridge girders and also has upper tracks to control the push from the ram. Two of the single-flange trolley wheels are driven by a one and a quarter hp dc motors equipped with magnetic brakes. The ram is raised and lowered by a 20 hp dc motor equipped with a magnetic brake. A full stroke of a little over 14 ft is given the ram through its rack and pinion drive and the spade can be pushed down into a loaded car with a force of about 20,000 lb. A 15 hp dc motor with a magnetic brake is applied to this drive and is able to swing the ram 45º either side of the vertical. The usual procedure in emptying a coal car is first to drive the sharp spade down through the coal until the pocket is opened and the coal starts to run out the hopper. When all the hoppers are open, the sweeping action of the ram and spade is used to move the remainder of the coal in the car over to the open hoppers. The travel of the trolley permits cleaning the sides of a coal car with the edges of the spade, using the sweeping motion of the ram. It is still necessary to clean out the corners of the car by hand. Final Clean-Out This unloader was a new development and there were improvements to be made before it was completely satisfactory, such as reduction in speed and conversion to ac drive motors. However, it helped at Marysville and unloaded many frozen cars that would have taken a lot of heating to thaw out enough for the old unloader to handle. The mechanical coal unloader described above was a considerable improvement but still left a job to be done by hand-the final cleaning out of the coal cars. The ram had the ability to open a hole through the hopper cars, but did not meet required unloading speed. To eliminate hand cleaning a car shakeout, manufactured by Hewitt Robins, Inc. was added to the installation. This equipment is used to clean the coal car out after the unloader has provided an

Jan 1, 1952

By J.W. Halley

The effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. Published Work A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease' in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimml found no change in Olsen ductility, Kockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.1j per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0. 50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. Experimental WoRk Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1943

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By T. M Morris

THE rate of flotation of solid particles determines the percentage recovery of these particles which can be obtained during a given time interval. It is an established fact that the recovery is greatest in the fine sand size range and falls off on either side of this size range. It is also a fact that the history of the development of concentrating devices has been marked by a desire to recover the small particles: tables were developed to treat material too fine to recover in jigs; flotation recovers material too fine to be recovered on tables. As our ores become more complex and require finer grinding, a greater proportion is in the slow-floating size range. It is therefore of economic importance that the effect of size of particle upon rate of flotation be studied. Many studies have been made along this line. The present investigation attempts to quantify the rate of flotation by means of a rate equation, and then compares the effect of size upon the rate of flotation. It was found that the flotation rate constant increases with increase in diameter of particle in the size range smaller than the optimum size particle. The flotation rate constant decreases with an increase in diameter of particle in the size range coarser than the optimum size particle. This suggested two different actions taking place, and these are discussed. Suggestions for further work in order to improve the flotation rate of both fine and coarse particles are made. The usual method of expressing rate is to plot cumulative percent recovery vs time. If we knew the equation of this kind of curve we could replot it as a straight line, and the slope of the line would be an index of the magnitude of the flotation rate. It is easier to compare straight lines than curves. The basis used for obtaining the equation of the recovery vs time curve is the law of mass action. This law states that the "rate of a chemical reaction is proportional to the 'active masses' of the reacting substances present at any given time." This, of course, implies a constant temperature. We can modify this for our use by using the term flotation reaction instead of chemical reaction and the term floatable particle instead of active masses. dC Thus----— kc [1] where C denotes concentration of particles, t denotes time, k denotes a proportionality constant. If the exponent of C is 1, then we have a first order rate reaction. If the exponent of C is 2, then we have a second order rate reaction. For a first order rate reaction, we obtain, after integration, where k is again a proportionality constant and has the dimension of the reciprocal of time. C, is the original concentration or weight or percentage of floatable particles. C, is the concentration or weight or percentage of floatable particles remaining in the flotation cell after time t. If all particles of the mineral to be floated were capable of floating we could take C, as 100 and C, would be 100 - R, where R is the cumulative percentage recovery of mineral at time t. But it is not usual for all of the particles to be capable of floating, because of surface oxidation, etc. Therefore, we must introduce a factor x which is the percentage of un-floatable mineral. Hence the first order equation is It has been proposed by various workers1-' that this equation describes the flotation rate. More recently N. Arbiter4 states that a second order rate equation fits the recovery vs time curve more closely than does a first order rate equation. Morris- as discussed the evidence presented for this statement. It has been concluded that the first

Jan 1, 1953

By Morris Muskat, J. M. McDowell

In both production and refining operations of the oil industry many processes are controlled by the gas-liquid phase relationships of the hydrocarbon mixtures of interest. The quantitative behavior of fractionating or distillation columns and stills depends on the changes in the equilibrium distributions of the hydrocarbon components between the gas and liquid phases as the pressure or temperature conditions may vary along the length of the column or as the gross operating parameters and compositions are varied. In oil producing operations the nature and amount of gas phase developed within an underground reservoir as it is being depleted and its pressure declines also involve the basic equilibrium gas-liquid phase interactions. The influence of surface conditions of temperature and pressure and various separation procedures on the nature and amount of stock tank oil and natural gas recovered from a given well stream is likewise determined by the same basic phase equilibrium characteristics of the hydrocarbon systems. Such equilibrium separation of the gas and liquid phases in a well stream is of importance both in establishing optimum separator conditions for obtaining maximum stock tank oil yields and in the general problem of crude stabilization. The phenomena involved in these problems and their quantitative aspects can, of course, be established in each individual instance by appropriate laboratory experimentation. It has been found, however, that by associating with the individual hydrocarbon components functional characteristics de- scribing their individual gas - liquid phase equilibrium behavior, the phase properties of the composite mixtures can be predicted by mathematical computation. These characteristics have been termed "equilibrium constants", or "equilibrium ratios"," and are defined by the general equation: where K, is the equilibrium ratio for the jth component, y, is the rnol fraction of that component in the gas phase, and xj is the corresponding mol fraction in the coexisting liquid phase. Considering the Kj as representing available and measurable properties of the individual components of a mixture, and as defined by Eq. (l), it is readily shown that in a coexisting gas-liquid system the rnol fraction concentrations of the individual components in the gas phase, y,, and those in the liquid phase, x,, are given by the expressions: where the nj are the corresponding rnol fraction concentrations in the composite system, and ng is the mol fraction of the whole which is in the gas phase. The basic unknown in Eq. (2) is n,: which gives the gross separation between the gas and liquid phases. This may be determined in principle by imposing the requirement that the sums of the mol fractions in both the gas and liquid phases are unity, i.e. by the equations: The solution of the equivalent Eqs. (3) lying between 0 and 1, when inserted into Eqs. (2), provides a complete description of the compositions of the coexisting gas and liquid phases. While the Eqs. (3) are essentially equivalent to polynomial equations, such transformations are of little value when dealing with multicomponent sys-

Jan 1, 1949

By E. Miller, N. Chou, K. Komarek

The solid solubilities of the compounds PbS, PbSe, and PbTe have been determined by equilibrating single crystals with two phase alloys. The solubilities were determined by measuring the Hall coefficient of the equilibrated samples. The observed maximum deviations from stoichiometry on the lead rich and the chalcogen-rich side of the phase fields were: at. pct excess Pb at pct excess S at 850°C; PbSe--4 x 10'" at. pct excess Pb at at. pct excess at 800°C; and PbTe-2.8 x 10 4 at. pct excess Pb at 780°C, 10"1 at. pct excess Te at 720°C. The previously developed theory of retrograde solubility has been expanded to include intrinsic disorder in the compounds, and the experimental results are in agreement with the theory. THE solid solubility limits of intermetallic semiconducting compounds are of considerable interest, since many of these compounds have potential use as thermoelements in thermoelectric devices, as infrared detectors, or in semiconductor devices. The solidus curves of a significant number of these compounds have been reported to be retrograde with the maximum solid solubility occurring between the eu-tectic and the maximum melting temperatures. In a previous paper,' equations were derived which permit calculation of the maximum solid solubility of an AB compound exhibiting retrograde solubility. Derivation of these equations was based on the assumption that the compound is a nondegenerate semiconductor at the temperature under consideration, that the defects were unassociated, and that the vibrational contribution to the entropy of the compound could be evaluated by the Einstein approximation. It was shown that at the temperature of the maximum solid solubility The entropy term ASS is composed of the entropy of formation of the solid stoichiometric compound (AS$)*, and the entropy due to deviations from stoichiometric composition which is the sum of a con-figurational term (aS*), a vibrational term (AS,), and an electronic term (AS,). In the previous paper the positional entropy was evaluated considering the con- N. CHOU, Member AIME, formerly Graduate Student, New York University, N. Y., is with IBM, Yorktown Heights, N. Y. K. L. KOMAREK, Member AIME, formerly with New York University, is Professor, Department of Inorganic Chemistry, University of Vienna, Vienna, Austria. E. MI LLER, Member AIME, formerly with New York University, is Associate Professor of Mechanical Engineering, California State College at Long Beach, Calif. The paper is based on a thesis submitted by N. CHOU to the Graduate Division, School of Engineering and Science, New York University, in partial fulfillment of the requirements for the degree of Doctor of Philosophy in Materials Science. tributions from defects arising from deviations from stoichiometric composition. The derivation is generalized in the appendix to include intrinsic disorder. The electronic entropy term is also recalculated in the appendix. Of the various semiconducting compounds, the solidus curves of Pbs,' and ~b~e,~ have been most extensively studied. The solidus of PbSe has also been determined, but the temperature of maximum solubility has not been accurately established.5129 The present investigation was undertaken to compare the experimental solid solubility data for these systems with the values predicted theoretically. Since the temperature and composition of the maximum solubility of PbSe has not been accurately determined, experimental emphasis was placed on determining the solidus curves for PbSe in the region of maximum solubility, although experiments were also performed on PbS and PbTe at several temperatures. X-ray diffraction studies were also made on carefully prepared powder samples of PbSe to determine the variation of lattice parameter with composition. EXPERIMENTAL PROCEDURE The procedure of Brebrick and Allgaier was employed for determining the solidus data. Monocrystal-

Jan 1, 1970

By J. M. McDowell, Morris Muskat

In both production and refining operations of the oil industry many processes are controlled by the gas-liquid phase relationships of the hydrocarbon mixtures of interest. The quantitative behavior of fractionating or distillation columns and stills depends on the changes in the equilibrium distributions of the hydrocarbon components between the gas and liquid phases as the pressure or temperature conditions may vary along the length of the column or as the gross operating parameters and compositions are varied. In oil producing operations the nature and amount of gas phase developed within an underground reservoir as it is being depleted and its pressure declines also involve the basic equilibrium gas-liquid phase interactions. The influence of surface conditions of temperature and pressure and various separation procedures on the nature and amount of stock tank oil and natural gas recovered from a given well stream is likewise determined by the same basic phase equilibrium characteristics of the hydrocarbon systems. Such equilibrium separation of the gas and liquid phases in a well stream is of importance both in establishing optimum separator conditions for obtaining maximum stock tank oil yields and in the general problem of crude stabilization. The phenomena involved in these problems and their quantitative aspects can, of course, be established in each individual instance by appropriate laboratory experimentation. It has been found, however, that by associating with the individual hydrocarbon components functional characteristics de- scribing their individual gas - liquid phase equilibrium behavior, the phase properties of the composite mixtures can be predicted by mathematical computation. These characteristics have been termed "equilibrium constants", or "equilibrium ratios"," and are defined by the general equation: where K, is the equilibrium ratio for the jth component, y, is the rnol fraction of that component in the gas phase, and xj is the corresponding mol fraction in the coexisting liquid phase. Considering the Kj as representing available and measurable properties of the individual components of a mixture, and as defined by Eq. (l), it is readily shown that in a coexisting gas-liquid system the rnol fraction concentrations of the individual components in the gas phase, y,, and those in the liquid phase, x,, are given by the expressions: where the nj are the corresponding rnol fraction concentrations in the composite system, and ng is the mol fraction of the whole which is in the gas phase. The basic unknown in Eq. (2) is n,: which gives the gross separation between the gas and liquid phases. This may be determined in principle by imposing the requirement that the sums of the mol fractions in both the gas and liquid phases are unity, i.e. by the equations: The solution of the equivalent Eqs. (3) lying between 0 and 1, when inserted into Eqs. (2), provides a complete description of the compositions of the coexisting gas and liquid phases. While the Eqs. (3) are essentially equivalent to polynomial equations, such transformations are of little value when dealing with multicomponent sys-

Jan 1, 1949

By G. R. Fitterer

Trends in slag composition in acid open hearth practice, particularly the variation in iron and manganese oxides during refining, are reviewed. A procedure which is currently being used to control the refining reactions is described and partially explained through slag phase diagram considerations. In addition, the ionic nature of these slags is considered and it is proposed that silica combines with the oxide ion and forms a series of complex silicate ions. The effect of basic oxides such as FeO, MnO, and CaO is apparently additive in furnishing the oxide ion for this purpose. IT is now possible to control192 the refining of steel in an acid open hearth furnace to a surprising degree. This control has been brought about through the knowledge and use of several facts and tests. These are: 1—A planned charge analysis based on a knowledge of the type of fuel, the bath depth, etc. 2—Knowledge and control of rate of fuel input as well as its method of atomization, if any. 3—Determination of the slag fluidity. 4—Bath temperatures (use of the Pt-Pt-Rh thermocouple). 5—Periodic determination of carbon content (use of the Carb-analyzer or Carbometer). Through the use of these control methods, a heat may be made to "melt-in" with or without residual manganese and silicon. The rate of refining or carbon elimination may be controlled accurately, and the desired tapping (or "go-ahead") carbon may be approached at a rapid or slow rate according to preference and type of steel being made. Thus operating time may be predetermined and greatly reduced. Further, all of the refining can be done without any ore or other oxidizing additions, and the heat may be brought to the desired tapping temperature simultaneously with the attainment of the desired carbon analysis. This control procedure is being used in most acid plants in the United States today and has been de- scribed.', ' Although the slag metal relations are sufficiently well known to control the heat as stated, yet it is possible to account for only about two-thirds' of the 0, which must have been used for the elimination of the carbon and other metalloids. Phase diagram studies' of the slags, slag weights, the metal particle theory,' ore additions, limestone additions, etc., may all be taken into consideration; yet, the mechanism of oxidation and source of all the oxygen remain to be explained. This paper reviews some of the principles upon which the control methods were based and proposes other possibilities regarding the unexplained phenomena. Old and New Acid Open Hearth Practice Some of the recent statements in the literature regarding acid open hearth operation are based on old heat data which are not typical of modern American practice. These old heat logs have been responsible for many misconceptions regarding the acid hearth practice and represent heats which do not coincide with modern methods. In recent years, American practice has been altered materially and these changes will be briefly described. Modern American Practice: A typical log of a modern American acid open hearth heat' is shown in Fig. 1 which indicates that the refining time was only two hours, during which the carbon was eliminated rapidly and the bath temperature increased at a fast rate. The manganese and silicon contents of the metal were essentially eliminated and their oxides had become constituent parts of the slag at the "melt-down" period. During the course of the heat, the MnO content of the slag remained practi-

Jan 1, 1954

By P. M. Blair, D. W. Peaceman

The shape and position of the gas-oil transition zone during downdip displacement of oil by gas has been calculated using flow equations which include the effects of gravity, relative permeability, capillary pressure and compressibility of the fluids. The calculations treat the problem in two space dimensions, and results are compared with data from a laboratory model tilted at 30° and 60° from the horizontal on displacements near and above the maximum rate at which gravity segregation prevents channeling of the gas along the top of the stratum. The good agreement between calculated and experimental results demonstrates the validity of the tecbnique as well as that of the flow equations. INTRODUCTION Knowledge of the fluid distribution and movement in an oil reservoir is important in producing operations and estimation of reserves. The history of the oil industry has included steady progress in improving the accuracy of calculations which provide the required knowledge. The earliest method of calculating reservoir performance consisted of material-balance equations based on the assumption that all properties were uniform throughout a reservoir.l For many reservoirs such a simple formulation is still the most useful. However, when large pressure and saturation gradients exist in a reservoir, the assumption of uniform values throughout may lead to significant error. To reduce these errors, Buckley and Leverett2 introduced a displacement eqation which considers pressure and saturation gradients. Methods available at that time permitted solutions to the Buckley-Leverett equation in one space dimension; these solutions have been very useful in solving many problems related to the production of oil. However, the one-dimensional methods are not adequate for systems in which saturations vary in directions other than the direction of flow. An example of such a system is the case of gas displacing oil down a dipping stratum in which the gas-oil contact becomes significantly tilted. Of course, the Buckley-Leverett displacement method cannot predict the tilt of the gas-oil contact. Recent improvements3,4 of the one-dimensional Buckley-Leverett method achieve some success in predicting the tilt of the gas-oil contact at sufficiently low flow rates. However, at rates high enough that the viscous pressye gradient nearly equals or exceeds the gravity gradient, even these improved one-dimen,sional methods incorrectly predict the shape and velocity of the contact. Further progress in estimating such fluid movements in a reservoir appears to require consideration of the problem in more than one space dimension. The recent two-dimensional method of Douglas, Peaceman and Rachford5 appears adaptable to calculate changes with time of the saturation distribution in a vertical cross-section of a reservoir. The movement of saturation contours should represent the moving fluid contacts and include the effects of crossflow due to gravity, as well as variations in the rock and fluid properties. The nonlinear nature of the equations used in the method has prevented proof of the validity of the solutions. Douglas, Peaceman and Rachford made some comparisons with experiment but did not include cases in which gravity was important nor cases involving displacement by the nonwetting phase.For these reasons, a test of the two-dimensional method for a case in which these factors are included would be very desirable. The test selected was a comparison of calculated results with those from a carefully controlled laboratory experiment on a model with measured physical properties. The model selected was one in which gas displaced oil down a tilted, rectangular sand pack. The model can be thought of as representing a vertical cross-section taken parallel to the dip of a reservoir. The displacement thus simulates gas displacing oil downdip that might result from gas-cap expansion or gas injection. This report outlines the calculation method used

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By W. G. Pfann

Under certain conditions, a molten zone can be made to move through a solid by impressing a stationary temperature gradient across the solid. This phenomenon can be utilized in fabricating semiconductive devices, growing single crystals, joining, boring fine holes in solids, measuring diffusivities in liquids, small scale alloying, and purification. Fundamentals and exemplary applications are outlined. ANEW aspect of the travel of a molten zone through a solid is considered in this paper. Whereas, in previously described zone melting techniques,'-' zones were usually caused to move by changing the position or temperature of a heat source, in the present technique a zone is made to move by impressing a temperature gradient across it. For example, a thin layer of molten A1-Si alloy, sandwiched between two silicon slabs having a temperature gradient normal to the layer, will travel through the hotter slab. One feature of temperature gradient zone melting, as this technique will be called here, is that zones of unusually small dimensions can be maintained. This leads to such diverse uses as have been listed in the abstract. In this paper fundamentals of the movement of a molten zone in a temperature gradient, and some practical applications thereof, are outlined. Assumptions The movement of a molten zone through a solid body of solvent substance in which a temperature gradient exists will be discussed. The length of the zone will be its dimension in the direction of motion. The direction of the temperature gradient will be toward the region of higher temperature. To be considered is a binary or higher order solute-solvent system in which the concentration of solute in the molten zone is sufficient to produce a lowering of the freezing temperature of the solvent which is at least of the order of the temperature range impressed on the charge. While we discuss primarily molten zones in a solid matrix, the principles are applicable to solid or vaporous zones in a solid matrix, a requirement being that the diffusivity in the zone be substantially greater than in the matrix. Diffusion of solute into the surrounding solid will be assumed negligible. In general, its presence will not basically alter the conclusions to be drawn. For illustration, a system represented by the partial constitutional diagram of Fig. la will be discussed, in which k, the distribution coefficient defined in the figure, is constant and less than unity. However, the technique is applicable to any solute- solvent system in which one component lowers the melting point of another component. Movement of a Molten Zone in a Temperature Gradient Consider, in the system AB of Fig. 1, where B is designated the solute and A the solvent, the effect of sandwiching a thin layer of solid B between blocks of solid A and placing the whole in a temperature gradient such that the temperature of the layer is above the lowest melting temperature of the system. Surrounded by an excess of A, the layer will dissolve A, becoming molten, and expand in length." As so- lution of A continues, at both interfaces, the mean solute concentration in the zone will move to the right in Fig. la, until at temperature T, the liquid at the cooler interface reaches the liquidus concentration C,. Solution of A thereupon ceases because the liquid T1 is saturated with A. The liquid at the hotter end of the zone, being at temperature T2, is not saturated with A at concentration C1. Hence solution of A continues there and concentration C2 is approached. A concentration gradient therefore is set up in the zone, causing A to diffuse toward the cool end and B toward the hot end. As a result, the liquid at the cool interface becomes supersaturated and a layer of crystalline A containing concentration kc, of B in solid solution freezes. Since a source of A

Jan 1, 1956

By J. T. Norton, J. G. McMullin

The ternary system of gold-silver-copper is characterized by a solid solubility gap and a two phase region in which copper-poor and silver-poor phases coexist. At about 30 pct gold, the two phases become mutually soluble at temperatures below the melting temperature. As the gold content is increased, the solubility temperature of the alloys decreases until at about 80 pct gold, the two phases are soluble down to the lowest temperature at which the alloys will recrystallize. Although the general form of the two phase region is known, its boundaries do not seem to have been investigated extensively. In an X ray diffraction study, Masing and Kloiberl have outlined the boundaries of this two phase field at 400 and 750°C. Using only microscopic techniques, Pickus and Pickus2 determined a vertical section of the ternary diagram showing the 14 kt alloys (58.3 pct gold). These two reports are riot in complete agreement. It has been shown3 that some of the ternary alloys are susceptible to age hardening and that the hardening is caused by the separation of a homogeneous alloy into two phases at the aging temperature. While the gold-copper binary system is an outstanding example of super lattice formation, Hultgren4 has shown that a few per cent of silver added to gold-copper destroys the tendency for ordering. Because of the age hardening possibilities of these alloys, it seemed advisable to investigate the boundaries of the two phase field more in detail using an X ray diffraction method, so as to permit a better understanding of the aging phenomena and enable predictions as to the behavior of other alloys to be made. This is especially true for the 18 kt alloys (75.0 pct Au) at the lower temperatures since they are known to exhibit age hardening. Twelve ternary alloys were prepared having the compositions shown in Table 1 and graphically in Fig 1. The gold used was fine gold bars supplied by Handy and Harmon. The silver was a bar of high purity silver from the U. S. Bureau of Standards. The copper was a bar of vacuum-treated, high conductivity copper from the National Research Corporation. The pure metals in the form of powder were weighed out in proper proportions and melted in graphite in a high frequency induction vacuum furnace. They were heated to 1100°C and slowly cooled. The ingots were then removed from the crucible, inverted, returned to the crucible and remelted. This remelting procedure was intended to reduce segregation in the ingots. After remelting, the ingots were checked for weight loss. The weight loss in each ten gram ingot was held to less than 25 mg. The remelted ingots were cold rolled and then given a homogenizing heat treatment of 16 hr at 760°C to remove any remaining segregation. Powder specimens were prepared by cutting the ingots with a fine file, one half the required amount of powder being taken from each end of the ingots. When the X ray diffraction pattern showed any difference in lattice constant between the ends of the ingot, the ingot was remelted and given an additional homogenization treatment. All powder samples were sealed in evacuated pyrex tubes for heat treatment. Ordinary pyrex proved satisfactory for temperatures up to 650°C but above that temperature it was necessary to use a special high temperature pyrex glass. Annealing at temperatures below 500°C was done in a salt bath whereas for temperatures of 500°C and above an electric muffle furnace was used. In both furnaces the temperature control was ± 5°C. In all annealing treatments samples of cold worked powder were placed in a furnace which was already at temperature. In this manner the specimens recrystallized directly to the equilibrium structure for that temperature. Time at temperature was selected so as to allow complete recrystallization, but very little grain growth. Specimens were quenched from the annealing temperatures by breaking the pyrex tubes in cold water. X ray diffraction photograms were made of all the heat treated powders using copper radiation and a Phragmen

Jan 1, 1950

ONE of the largest hard rock operations ever undertaken on the continent is part of the Aluminum Co. of Canada's gigantic British Columbia development in the mountainous wilderness back of the north coastal port of Prince Rupert. To provide electric power for the huge aluminum smelter under construction at Kitimat, 400 miles northwest of Vancouver, Alcan is reversing the flow of a 5000 sq mile drainage area by blocking the eastward-flowing Nechako River with the largest sloping clay core dam in the world. The backed-up waters of a 110-mile chain of lakes will be tapped at their eastern end by a 10-mile tunnel piercing a mile-high mountain range. From this tunnel water will pass through penstocks to a subterranean powerhouse after a drop of 2600 ft and empty into the Kemano River almost at tide water. A projected battery of eight turbine-driven generators will produce more than a million horsepower, although, initially, three generators of 140,000 hp each will be installed. Power will travel 50 miles across another mountain range, over a glacier, and across an arm of the ocean to what will ultimately be the world's largest aluminum smelter-a plant 2 ½ miles long. Ore smelted at Kitimat will come from Jamaica, but carving the tunnel, penstocks, and powerhouses cavern out of the heart of a mountain is so vast a job that most of the problems of a major mining operation are encountered. The powerhouse cavern alone is a big hard rock job. This chamber lies 1400 ft back from the mountain face and will eventually be 1100 ft long, 80 ft wide, and an average 118 ft high. Now under construction, the roof of this cavern will take the form of a parabolic arch. The prime contractors, Morrison-Knudsen Co. of Canada, are to excavate a length of 700 ft by May 1954. This section will provide a main control room, erection bay and space for eight generating units. The roof arch is to be lined with reinforced concrete and a plan now under study provides for concrete curtain walls separated from the rock sides of the cavern to prevent moisture accumulation. Cavern Excavation Excavation of the cavern began with the driving of an 8x8-ft exploratory drift 1500 ft long. Two horseshoe-shaped access and tailrace tunnels were bored to serve excavation work. These tunnels are approximately the same length as the exploratory drift and 25 ft high. The floors of both tunnels were graveled to permit the use of rubber-tired equipment. Eventually, the tailrace tunnel will be enlarged to 40 ft height to drain water from the turbine pits below the powerhouse floor. When the tunnels reached the cavern location, a mucking tunnel, approximately 25 ft square, was driven the projected length of the powerhouse at the floor level of the cavern. Another tunnel, 10 ft square, was carried in the same direction from the exploratory drift at the level of the arch spring line, 65 ft above the cavern floor. To connect these two tunnels, seven shafts 10 ft wide and approximately 80 ft long were driven through to the lower mucking tunnel, 65 ft below. These shafts were located on 120-ft centers, the length of the powerhouse cavern. Blasting is done from this upper tunnel to the final line of the roof arch. Two bulldozers, an International TD-24 and a TD-9, doze blasted material to the shafts where it drops to floor level. From here, the rock is loaded by Eimco loaders and power shovels into rubber-tired Koehring Dumptors and Euclid end-dump trucks. The arched roof section will be completely excavated and concreted before vertical blast holes are drilled down from the level of the arch spring line to the floor of the cavern. The arched roof section with its parabolic curve will have a width of 80 ft and a rise to the crown of 47 ft.

Jan 1, 1952

By Terkel Rosenqvist

J. Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—The fact that the experimental work has been applied to copper rather than iron and that the paper is presented to the Iron and Steel Division, I regard as rather significant. It shows the unity of metallurgy and the fallacy of trying to cut it up by metals. This result for the solubility of sulphur in molten copper correlates with Professor Schuhmann's finding that the published data on the other side of the copper-sulphur miscibility gap are also in error. I should like to ask the author to say a little bit more about the sulphur capacity of the slag. T. Rosenqvist (author's reply)-—I hope that Dr. Chipman will find the derivation of the expression for sulphur capacity more clearly explained in the printed version of the paper than in the oral discussion at the meeting. I feel that this quantity, which actually is the ratio of two activities, can be measured more easily than the individual activities. Even if the ratio CaO/CaS is chosen as the standard state, the expression can be used for any slag, even for slags completely free of lime, and it represents a way to put the desulphurizing power of all slag constituents into one bag. Some doubt has been expressed as to whether oxygen ions really exist in calcium oxide and in molten slags. From a thermodynamic view point that question is of minor importance. The term oxygen ion activity, or any activity for that matter, is defined rigorously by the equation: activity = exp p/RT, where p is the change in free energy connected with the transfer of one mol of ions from the standard state into the slag. Whatever happens to the ion in the slag is of no concern to the thermodynamicist. Regardless of whether the ion is "free" in the slag or not, or whether it is present in a very small amount, its activity can always be expressed, and for a thermo- dynamic calculation that is all we need. However, ionic activities will only be of some real value if they are simple functions of the slag composition, or can be measured easily. Concerning the real nature of the oxygen in the slag, my feeling is that the oxygen atom has a rather multiplex nature depending on how strongly it is tied by covalent forces or polarized by the other atoms or ions present. The oxides of iron, cobalt, and nickel differ from calcium oxide and blast furnace slags as to the amount of free electrons that can give rise to electronic conductivity. In slags we know that the conductivity is mostly ionic. The fact that reversible emf's can be obtained with oxygen electrodes in certain salt melts, indicates a significant amount of oxygen ions in these melts. But extended work, e.g. polaragraphic studies and measurements of transference number; are needed to obtain quantitative information about the real structure of the slags. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—-With reference to the ion, it might be well to remember Dr. Moses Gomberg. All of his life he had no use for the ionization theory and he contributed greatly to the field of chemistry on the assumption there was no such thing as ions. I do not think we have to worry about whether the oxygen is ionic or not. I think one thing specifically should be brought to your attention and this I think is one of the important contributions of Dr. Rosenqvist. He pointed out what we know as oxygen potentials or what is described as oxygen potentials. I have used this concept for a long period of time and I want to state that if this concept is properly applied, it vitiates much of what we have in the literature, or makes our usual ideas regarding oxidation seem primitive. That one thing is more valuable than almost all the rest of the discussion as a fundamental basis on which to build a reasonable in-

Jan 1, 1952

By H. M. Myers, J. E. Funk

The two-phase flow of a drilling fluid in a diamond drill bit is investigated by deriving and solving the steady-state continuity and momentum equations. Parameters in this analysis are rotational speed of the bit, local rate of addition of drill solids, non-Newtonian nature of the drilling fluid and drilling rate. The describing equations relate the flow and pressure drop to the design characteristics of the bit. The equations are integrated numerically yielding the flow-rate pressure drop characteristics for the bit, flow distribution in the bit and velocity and static pressure as a function of position in each flow channel of the bit. Results are presented for a particular bit design. This paper shows that under normal drilling conditions certain parameters may be neglected in the hydraulic calculations for a diamond drill bit. Therefore, shortened forms of the equations presented can be used to fit the proper diamond bit to the drilling fluid hydraulic system. INTRODUCTION Like the conventional bit, the diamond drill bit is a key component in the circulating system of a well. The conventional rock bit is fitted to the circulating system by selecting the flow nozzles which provide the system with the proper flow-rate pressure drop relationship. Fluid behavior across the face of the diamond bit must be better understood so the bit can also be fitted to the circulating system. Data from field-operated diamond bits are presently available and do yield some information regarding the flow-rate pressure drop relationship. However, the number of factors affecting this relationship is quite large. Drilling parameters and conditions such as bit penetration rate, bit weight and rotational speed are important. Moreover, flow channels in the bit are part of the cutting head, and introducing drilled solids into the flow channels reduces the flow area, causes additional drag and influences the pressure drop. Many tests would have to be performed if field tests were required to study all parameters which might influence fluid behavior in the bit. A logical approach to this problem is to investigate analytically the fluid behavior in the bit, including parameters that are present under normal drilling operations. This approach, which seems to offer the best method for future studies, is presented in this paper. Following is the general procedure. 1. Equations describing the most general flow channel are written and include the addition of drilling solids (which is related to penetration rate), rotation of the bit, design parameters of the bit and non-Newtonian properties of the fluid. 2. A typical bit is designed and the bit parameters are substituted into the equations. 3. Parameters are assumed (penetration rate, rotational speed of the bit, mud weight, etc.). 4. The describing equations are numerically integrated to obtain the pressure drop across the face of the bit as a function of flow rate. 5. The pressure-drop contribution of each component (friction, acceleration, etc.) is obtained from the numerical solution, and those factors which largely influence the total pressure drop are identified. Classifying the drilling fluid is important in establishing the friction factor relationship since the frictional pressure losses are the main contributors to the total pressure drop. High-density drilling fluid is commonly assumed to be a Bingham plastic. 1-3 Govier4 presented a method for selecting a friction factor in the laminar flow region from the rheology properties of the mud and a modified Reynolds number. Metzner5 presented a criterion for selecting the friction factor in the turbulent flow region. The bit design used in conjunction with the solution of the equations has divergent flow channels. Stall, which is the backflow of fluid in the channels due to eddies that occur on the outer perimeter of the flow stream, can occur in these divergent channels (or diffusers). When stall does occur the static

By J. W. Halley

The effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. Published Work A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease' in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimml found no change in Olsen ductility, Kockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.1j per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0. 50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. Experimental WoRk Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1943