Search Documents

By Ralph M. Hunter

Until recent years, maintenance of surface coal handling facilities was a relatively simple task. Equipment consisted principally of conveyors, screens and crushers of comparatively simple construction. Electrical equipment consisted of motors and starters, with little, if any, interlocking. In most cases failure of any component affected only the grades of coal loaded so that even a prolonged breakdown did not affect mine operation materially. However, with the introduction of modern cleaning plants, the picture has changed. The equipment is much more complex and therefore more difficult to maintain. In many cases failure of any component of the plant prevents loading of coal. Even if provision is made to bypass, the quality of coal loaded is lowered, affecting markets. In the case of plants designed to permit full seam mining, marketable coal cannot be loaded without operation of the cleaning plant. Under these conditions it is apparent that considerable thought and effort toward better maintenance are justified. In order to assure continuous, efficient and economical operation, maintenance should receive consideration, not only after the plant is in operation, but while it is being designed. It is hardly necessary to say that the designer should strive for sturdi-ness and wearing qualities. It is sometimes not realized, however, that even the best parts will sooner or later require replacement or repair. The designer should, there- fore, give consideration to accessibility. Anyone who has had to do with cleaning plant maintenance is familiar with installations where several hours are required to get at a part that can be repaired or replaced in a few minutes, once it is accessible. As in most cases, experience is the best guide. The men who operate and maintain this equipment know the problems encountered. Whenever available, the opinions of these men should be sought and heeded. As an example, we might consider the refuse elevator on a Chance Cone. Our company is now operating three of these cones, the first of which was installed in 1941, and the latest in 1946. Exact records are not available, but well over 50 pct of delays charged to the Chance Cones have been caused by the refuse elevator. This elevator receives refuse from the cone and carries it to a point above the water level of the cone, discharging onto a dewatering and desanding screen. Since the elevator operates under water and necessarily has close clearances in the lower boot, it tends to jam on large pieces of refuse or tramp iron. The chain, buckets and boot are also subjected to the action of water, sand and refuse, which accelerate normal wear. In case of jamming or chain-breakage it is necessary to drain the elevator and the cone so that even a minor fault in the elevator causes a considerable loss of time for the cone. In our new plant, which will contain two Chance Cones, the refuse elevator has been eliminated. This was accomplished by raising the cone so that the refuse gates could discharge directly onto the dewater-

Jan 1, 1949

By Spruille Braden

My attendance at this seventy-fifth Anniversary banquet of the A I M E is for me a homecoming, It means renewing associations with old friends, breathing again 'the invigorating mining atmosphere in which I was born and reared, and being among those who remember with affection and esteem the man from whom I inherited a name so intimately linked to-the mining profession Tonight, like a prodigal son strayed from mining into the far countries of diplomacy, I return, to eat and be merry over the fatted calf on this pleasurable occasion , While there is no riotous living in modern diplomacy, you are no doubt convinced that neither did I suffer a mighty famine in those far lands When I entered the Foreign Service, a few mining friends, viewing diplomats as sartorial perfectionists, or "striped pantsers" preoccupied with the art of cookie pushing, no doubt thought me a lost soul Conversely, some of my new colleagues at first looked upon me captiously and later as a reformed character, because they believed all miners to be rough customers, attired in muddy boots and given to direct action and equally direct or even explosive speech In point of fact, these two professions have much in common I do not have in mind the parallel cynicisms that "a miner is a liar with a hole in the ground" and "a diplomat a man sent abroad to lie for his country " I do

Jan 1, 1947

By W. L. Falke, A. A. Cochran

A basic problem in connection with manganese is to find economical ways to utilize domestic resources. As a part of its program to conserve domestic mineral resources and to reduce dependence of foreign sources, the Bureau of Mines had conducted extensive research to broaden manganese technology and to find economical, technically-feasible processes for recovering manganese from these low-grade resources. This paper analyzes some of the major difficulties which have been encountered in previously proposed processes for treating low-grade manganese ores and discusses a process which may circumvent many of these difficulties. Vast deposits of low-grade manganese ore exist in the U.S., yet domestic production is insignificant compared to the more than 2 million tons of ore imported yearly into this country.' A basic problem in connection with manganese is to find economical ways to utilize domestic resources.2 As a part of its program to conserve domestic mineral resources and to reduce dependence on foreign sources, the Bureau of Mines has conducted extensive research to broaden manganese technology and to find economical, technically feasible processes for recovering manganese from these low-grade resources. Although a great many processes have been proposed for treating domestic manganese resources, a failing of many of them is that too many steps are involved for economical operation.' Some of the major processes that have been proposed were reviewed by Norman and Kirby.3,4 Chlorination processes have become increasingly useful as a means of recovering valuable metals from raw materials, because the relative cost of chlorine (Cl2) and hydrogen chloride (HC1) has decreased through the years, and because the corrosion resistance of materials of construction has been improved. The objective of these processes is to form metal chlorides that are more volatile or water-soluble than are the corresponding oxides or sulfides; these compounds then can be separated from the gangue or other minerals by volatilization or leaching. Several chlorination processes for the recovery of manganese have been investigated by the Bureau of Mines5-8 and others; the major chlorination processes were reviewed in 1963, and their main features were compared.4 In all these processes, the simultaneous leaching or volatilization of iron chlorides with manganese chloride (MnCl2) is a problem, and the more iron that is present, generally the greater the problem. The leaching step is not highly selective, and the product of this step is, at best, suitable only for the production of ferromanganese or for further processing to remove iron. The product of the volatilization step is, in all cases, a mixture of iron and manganese chlorides that contains too much iron even for ferromanganese production, and must undergo additional processing steps for iron removal. THERMODYNAMIC CONSIDERATIONS The literature indicates that the desired chlorination reactions will proceed at practical rates at temperatures near 1200°K (927°C). Free energy changes at 1200°K for the critical steps of the reduction and chlorination reactions9-11 follow: Most of the research on chlorination processes for manganese recovery has been done with HC1 rather than with C12, for the following three main reasons: 1) Recycling of the chlorinating agent, which is economically vital, appeared to be easier for HC1

Jan 1, 1968

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By Peter J. Maxworthy

INTRODUCTION There is no hard and fast rule on whether functions within a company, diversified or otherwise, should be strongly centralized or decentralized. In all diverse organizations, there are certain basic functions which remain common (or central) to each element of the business, viz: Personnel Management Cash Management Taxation Management Legal Planning Accounting Standards It would follow that each of these common factors requires some supervision at a central level to ensure that overall group objectives are met. It is true that other functions including: Industrial Relations Marketing and Distribution Production Research and Development Purchasing Management Accounting may also be common to each element of the organization. However, there is far less commonality in the degree to which these functions are central to the efficient performance and financial well-being of the business. Role of Operating Units The resources of operating centers may be viewed as a bank of funds, the nature of which can be changed from time to time, but the employment of which must provide for ongoing increases in the net worth of the total enterprise expressed in terms of market values. Operating units are required to continually review products, methods, and opportunities and to monitor avenues for incremental investment--all with a view to attaining the necessary additive net present value of future cash flows of the enterprise. Operating units should be permitted sufficient autonomy to enable the best use to be made of the skills and experience of the people it employs in order to produce a return appropriate to the value of assets employed. Role of Head Office The head office will typically comprise a specialist group--the leaner the better if one strongly adopts the decentralist approach--often acting as Service Centers but also performing a control function in the corporate sense. The head office function is a cost center. It may be instrumental in developing strategies for increasing revenues or reducing costs on a group scale, but it does not generate revenue. Every dollar spent on this function is an extra dollar to be generated by the operating centers in order to achieve an increase in corporate wealth. TREASURY MANAGEMENT Treasury management is concerned with the provision of finance, cash-flow management, and risk analysis. Each decision taken within the enterprise has a cash implication. It follows that a well-integrated central Treasury function can, in all likelihood, produce economic benefits. The degree to which the function should be centralized depends largely upon the unique nature of the operating units it is servicing. Levels of ownership, the calibre of unit operating managers, and the nature and geographic distribution of the business are all factors determining the degree to which the Treasury function is centralized. In the case of Peko-Wallsend, the Treasury Department is small, comprising four people. While divisional cash-flow management is largely decentralized, Treasury is responsible for the daily management of funds surplus to the immediate needs of operating units. Treasury also operates as central banker and provides funds to

Jan 1, 1985

By Corliss R. Kinney

Since the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated Dace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. Possibilities of Acetylene One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1947

By A. M. Rowe

A considerable quantity of experimental hydrocarbon K-factor data has been correlated as a function of component identity, temperature, pressure and convergence pressure. To utilize these correlations effectively, convergence pressure must be determined accurately, particularly for volatile mixtures near their critical states. This paper presents phase diagrams that illustrate physically the meaning of convergence pressure. A new method, referred to hereafter as the "critical composition method", will be outlined for calculating convergence pressure. An example calculation has been included to illustrate how to use this new technique. INTRODUCTION The principle of hydrocarbon phase composition calculations as applied to such diverse problems as optimizing separator performance or predicting fluid compositions at various stages of reservoir depletion is the same. Usually, temperature, pressure and the numbers of moles of the various components of the fluid contained in a given volume are known. Questions answered by the phase calculation are what fraction of the total mass of fluid exists in each of the equilibrium phases, and what are the mole fractions of the various components in the two phases? To answer these questions the Natural Gasoline Supplymen's Assoc. (NGSMA) has correlated a considerable quantity of K-factor data as a function of temperature, pressure, component identity and convergence pressure.l To use these correlations to obtain the best answers possible, one must be able to calculate the convergence pressure. This is particularly true for over-all fluid compositions in the neighborhood of the critical state. STATEMENT OF THEORY Use of convergence pressure as a correlating parameter is based on a postulate similar to the law of corresponding states used in correlating PVT data of hydrocarbon gases. This postulate, which proposes convergence pressure as a correlating parameter, has been stated as follows: "The equilibrium vaporization constant for one component in a complex system is the same as the equilibrium constant at the same temperature and pressure for the same number or kind of components, providing only that the convergence pressures of the two systems are exactly the same at the same temperature and that the components are of the same homologous series".2 This law, as with all laws of physics, cannot be proven theoretically. It can only be justified by experimental data supporting its premises. Arguments have been made that this law violates Gibb's phase rule. For example, consider a four-component system. By Gibb's phase rule, which is thermodynamically rigorous, f = c — P + 2 =4, for a four-component, two-phase system. Thus, four independent intensive variables must be specified to establish completely all the intensive variables of the equilibrium phases. On the other hand, according to convergence pressure theory, only three variables need be specified for any mixture containing four different components. These variables are temperature, pressure and convergence pressure. Thus, the two laws appear to be in conflict. However, the convergence pressure postulate is more restrictive than Gibb's phase rule. It applies only to mixtures of the same homologous series. Hence, these two concepts are not in disagreement. PHASE DIAGRAMS DESCRIBING CONVERGENCE PRESSURE This paper presents phase diagrams grading from the simple two-component system to the more complex four-component system to illustrate convergence pressure. A less abstract definition of convergence pressure will be stated that is

By C. R. Dale

The need for instruments to measure the movement of fluids and gas in wells has been recognized by engineers for many years. Information regarding flow in the producing interval has a direct bearing on completion practices in new wells and also provides information on the production characteristics of the well. Many hours of engineering time are spent in planning and completing wells but knowledge as to whether or not the original planning has produced the desired results has not always been complete. Many questions such as the following often arise: Why is it that two wells are completed under supposedly identical conditions, yet one well is a good one and the other is a poor one? Are the sands that look the best on the electric log contributing to the production? These and many other conditions in the producing well need to be under- stood in order to develop more efficient production practices and to improve on methods of completing new wells. It is the purpose of this paper to briefly describe one type of instrument, outline the methods of running the equipment and show the results of surveys made under various conditions. With an understanding of the use of this type of survey its importance can be evaluated in relation to the problems encountered by the operator. DESCRIPTION OF INSTRUMENT The instrument is a velocity recorder employing a clock-controlled 16mm film for recording the rpm of an extremely sensitive rotor which is rotated by the flow of fluids or gas in a well. The helical-vaned rotor and shaft, weighing one-half of one ounce are an integral unit exposed to the well fluids and are the only moving parts not enclosed in the fluid-tight housing. No packing or fluid seal of these parts is necessary and the shaft is mounted top and bottom on special jeweled bearings. Fig. A is the lower part of the instrument showing rotor and shaft with the protecting housing sleeve removed. The rpm of the rotor is recorded on the moving film by a combination electrical and optical system. The record is a series of dashes on the film, each dash and space representing twenty (20) revolutions of the rotor. (Film record of survey made in California well showing station recordings at various depths.) As the movement of the film is controlled by the clock the number of dashes and spaces in one minute of film travel represents the rpm of the rotor. The range of the instrument is from 0 to 2,500 rprn. The barrel or housing is 1-11/16 in. OD and seven feet long. Various types of expanding fluid traps are attached to the lower end of the instrument to direct the flow through the 1 in. orifice containing the rotor. The fluid trap for upward flow is shown in Figs. B and C. This assembly consists of eight arms with light spring

Jan 1, 1949

By L. G. Graper, E. L. Ramsey

THE present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and' adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semikilled .as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. ADDING SULPHUR AS A SULPHITE These difficulties can be avoided if sulphur is introduced into the steel by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which-upon decomposition-forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig. I shows photomicrographs of steels made with sulphur, while Fig. 2 illustrates the structure of steels made with sodium . bisulphite. These samples were cut from the steels as cast-that is, before rollingand were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide -inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. z shows that the sulphide inclusions are more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. RESULTS As stated before, the sulphur dioxide-is added to steel by means of the decomposi-

Jan 1, 1942

By W. C. Krumbein

GEOLOGICAL problems are approached from a geometrical (space relations) viewpoint, a kinematical (time sequence) viewpoint, or a dynamical viewpoint. The first two require sound training in conventional geology and in field methods. The third approach requires a solid foundation of chemistry, physics, and mathematics. Modern training for geologists should include close integration of basic sciences with geological principles. INTRODUCTION Our knowledge of the earth has increased tremendously during the last half century. We know more about its surface configuration, the distribution of its natural resources, the procession of living forms that inhabited it in the past, the chemical composition of its oceans, the areal distribution of its surface rocks, the movements of its atmosphere, and so on. Not only do we know more facts about the earth, but we have a better understanding of the processes that take place on and within it, such as the nature of earthquakes, the thermodynamics of the atmosphere, the chemical equilibria involved in the formation of igneous rocks, the mechanics of stream flow, the dynamics of the earth's origin, and so on. Many sciences contributed to the sum total of this knowledge, including such established disciplines as geology, geography, physics, chemistry, astronomy, biology. Out of this accumulation of new knowledge grew also a group of new sciences, such as seismology, oceanography, meteorology, volcanology, hydrology. Collectively these latter are known as the geophysical and geochemical sciences, and to a large extent they began as branches of geology. Until the turn of the century, for example, the study of earthquakes (seismology) was a part of geology, although as early as 1846 Mallet, a physicist, had suggested that the subject could be investigated by elastic-wave theory. Comparatively little progress was made along these lines until the seismograph was developed near the turn of the century; since then, additional earthquake data have accumulated rapidly, but more important, the interpretation of these data essentially has kept pace with their accumulation. In similar fashion, meteorology, was generally considered a branch of geology as recently as one or two decades ago. Considerable progress had been made in such aspects as weather forecasting, but the science dates its recent rapid rise from the year 1911, when Bjerknes first applied the principles of dynamics to the analysis of air masses. The rapid development of such disciplines as oceanography, volcanology and hydrology was due in part to the application of principles of chemical equilibrium, of dynamics, and of thermodynamics to earth problems, by men who were essentially physicists or chemists by training. The last half century, therefore, and particularly the last two decades, saw the influx of numerous chemists and physicists into the realm of the earth sciences. In the meantime the main body of geology itself showed a marked growth, and

Jan 1, 1941

By William F. Harris, Joseph Easha

FOR many years basic control of refinery operations depended on visual observation of small chill specimens poured at various intervals during processing. The oseto of these samples was related to the physical and chemical properties of the metal. Since the =setn is dependent on many factors other than oxygen content, this method, while giving a general indication of the condition of the copper, does not accurately measure the oxygen content. For the last 3 years a modified vacuum fusion procedure which enables the operator to determine the oxygen content of the copper within 1 5 min of sampling has been in use at the Westinghouse Copper Mill. For use with this apparatus a sampling technique has been developed which gives oxygen values representative of the oxygen content of the wire bar. The sampling technique is based on a statistical study, which compared the oxygen content of the laboratory sample of copper poured at the same time a wire bar was being poured, with the oxygen content of the wire bar. The apparatus used for the determination of oxygen in copper is shown in Fig. 1 and is essentially the same as previously described but with one important modification. A very porous fritted glass disc has been inserted in the tubing between the manom- eter and 40/50 ground glass joint. The fritted disc retains the copper vapor and copper particles in the furnace section and prevents contamination of the mercury in the manometer. Without the disc the manometer became difficult to read after a few weeks of operation. In earlier work1 it had been established that the simplified vacuum fusion apparatus used at the Copper Mill gave essentially the same results as a con-vential vacuum fusion apparatus. However, for this study it was necessary to determine the difference, if any, between the oxygen content of the wire bar and the oxygen content of the small chill sample used for the oxygen analysis. This correlation was established by taking a chill sample at the same time wire bars were being poured. The wire bar being poured at the time the chill sample was taken was marked and removed for further analysis. The copper is sampled at various times during refining and cast into laboratory size samples with the mold shown in Fig. 2. The mold is made of cold rolled steel and is 2 in. high and 2 1/2 in. in diam. The large upper portion of the cast sample is used for measurement of the conductivity of the copper, The lower portion which is a rod about 1/4 in. diam by 3/4 in. long is used for determination of the oxygen content. This portion of the sample weighs about 5 g which is approximately the size sample used for the analysis. The only preparation neces-

Jan 1, 1962

By J. J. Bowman

The term "secondary aluminum" frequently is used loosely and often is considered synonomous with "inferior quality." Under war conditions, when every pound of material must contribute its share to the job at hand, this type of thinking is most unfortunate. Actually, given a supply of segregated scrap, an experienced smelter can produce remelted ingot of good quality, comparing closely to the analysis of the original material, and of considerable value of the war effort. The alloys he can produce are, of course, somewhat controlled by the analysis of the available scrap and, by the very nature of things, some of his production is not suitable for indiscriminate use. However, remelted scrap ingot provided about 273,2 per cent of this country's domestically-produced 1942 aluminum supply and probably will comprise about 39 per cent of the 1943 supply. (Canadian production is excluded from these figures.) That this part of the supply remains important is indicated by a recent report that "requirements" for the second quarter of this year were about 14 per cent greater than the supply, even though that supply will be almost twice the prewar annual production. (And those requirements, incidentally, were prepared after many conservation measures had been taken into account.) Since W. Bonsack recently has published a paper2 on the effects of the various alloying elements and impurities on the properties of aluminum, and such con¬siderations really are the important ones in a discussion of the metallurgy of secondary aluminum, it is planned to restrict this discussion more to a consideration of the sources, general characteristics and possible uses of these materials. For the purpose of this discussion, mill (or run-around) scrap may be disregarded and only plant scrap and obsolete scrap considered. Plant scrap, of course, is that scrap which is generated during the production of some part or assembly from a fabricated form of aluminum, such as sheet, tubing, forgings, castings or the like, and it may consist of solids (including rejected parts or subassemblies) or of machinings. To the extent that the several alloys are effectively segregated and the material is properly identified, the composition after remelting can be rather closely controlled or predicted. Obsolete scrap, on the other hand, is the "junk" which accumulates because of the wearing out or breakage of some piece of equipment. Although it is almost always in the form of solids, the accumulation includes many different alloys (often in the same assembly) and may include a considerable amount of nonaluminum material. The "metallics" recovered from drosses also contribute a portion of this class of material. The composition after remelting, therefore, may vary over rather wide limits and can not be very accurately predicted in any specific instance. SEGREGATION OF PLANT SCRAP Unfortunately, perhaps, it was not very common practice before the war to

Jan 1, 1943

By C. O. Brawner

Introduction The procedures used to design slopes in rock have only been developed over the past 10 years. Therefore, continued review and assessment of field experience by the publication of case studies is necessary to determine the accuracy of the theory and the application of the design techniques being used. Where failures have occurred, mine management should insist that the slides be 'back analyzed' to determine the shear strength parameters at failure. These values should be used for any pit design as they reflect site conditions more accurately than any other procedure. The previous papers have dealt with the basic concepts and factors that influence stability. To illustrate the application of these concepts in the study of practical stability problems, six ease studies have been selected for review. The examples include failure of tailings dams due to an earthquake, failure and redesign of a slope in overburden, review of failures of rock slopes, calculation of the amount of seepage into a pit and influence of the groundwater on stability, and the design of slopes for a proposed 2,500 ft. deep open pit mine. All but the first example are drawn from the authors personal experience. EXAMPLE 1 Failure of Tailings Dams Due to an Earthquake On March 28. 1965 a serious earthquake occurred in Chile with the epicenter located near the town of La Liqua, about 80 miles north of Santiago. The earthquake had a rating of 7 to 7.25 on the Richter scale. A record of the acceleration was taken at Santiago where a maximum horizontal acceleration of 0.18 g. was recorded. Many small mines are located in this region. Each of the mines provided impoundment storage for tailings with one to three dykes. As a result of the earthquake, most of the dams failed. The most serious failure involved two dams at El Cobre where more than 2,700,000 cu. yd. of tailings flowed into the valley, travelled over 7 miles in a few minutes, destroyed part of the town of El Cobre and killed more than 200 people. The Chilean government commissioned an investigation into the failures. A summary of the findings was published by Dobry and Alvare7 in 1967 (1). The location of the earthquake and the tailings dams which were investigated is shown

Jan 1, 1971

By Samuel M. Cassidy, George M. Rigg

During 1937 a program was begun to mechanize and modernize the then 28-year old Isabella mine of the Weirton Coal Co., which is on the Monongahela River, in Fayette County, Pennsylvania, at one edge of what is generally known as the Coke Region. Weirton Coal Co. is a subsidiary of the National Steel Corporation, and produces metallurgical grade coking coal for the Weirton Steel Co., Weirton, W. Va. Improvements subsequently made included a cleaning plant for washing the entire mine output, shovel-action track-mounted machines for mechanically loading all the coal, universal-type track-mounted cutting and shearing machines, post drills, 8-wheel mine cars of 10 tons capacity, cable-reel gathering locomotives and other auxiliary equipment. This paper presents the factors, reasons and results of decided changes from the mining system generally prevailing in the region, as well as abandonment of selective mining practices in favor of complete seam extraction. Coal-seam Conditions Fig. 1 illustrates the Pittsburgh coal seam on the property. Cover over the seam averages 450 ft., and 675 ft. is the maxi- mum. Main roof varies from very weak to medium strong; usually it disintegrates rapidly on exposure to air. The "wild" coal makes a fairly strong immediate roof if supported by crossbars and if unbroken affords a seal to the main roof. The draw slate is very weak and treacherous. The floor is characterized by numerous irregular bottom rolls, or "horsebacks," protruding from a few inches up to 3 ft. into the coal. Some are soft, but many are hard and flintlike. Although the bottom slate usually is hard, the underlying fire clay causes it to buckle and heave readily with any moderate increase in roof pressure or where damp. As a whole, the bottom is weaker than the main roof. The coal is characterized by numerous closely jointed face and butt cleats and a woody, springy nature when shot, both having a decided influence on face practices. As shown in Fig. I, at both the top and bottom of the main coal seam is a layer of coal of higher ash and sulphur content than the body of coal in the middle. Factors That Influence the Mining System Equipment was bought and organization for mechanical loading was made on the basis of working each mechanical unit as near its full capacity as possible, to lessen investment cost and obtain best operating efficiency. This led to combination double and triple-shift operation at the start, and, very shortly, to all sections being triple shifted.

Jan 1, 1947

By R. A. Generes, H. C. H. Darley

Laboratory tests showed that at elevated temperatures a reaction takes place between all metal hydroxides and clay muds, which results in a thickening or solidifying of the mud, the extent of which depends on the nature of the ingredients. Calcium hydroxide gave the strongest solidification whereas barium hydroxide only caused a mild thickening, indicating that the use of barium hydroxide muds instead of lime muds would be a good way of preventing high-temperature solidification. It was found possible to prepare barium mud in the laboratory with caustic soda and a thinner in the same manner as lime muds, and these barium muds had the same or better toleration of high solids content, resistance to salt contamination, and low gel strengths as the corresponding lime muds. Three field trials have been made with barium mud. The principal difficulty encountered was in determining the correct proportions of the tourly treatments required to maintain low gel strengths. A satisfactory systern was finally developed, and low gels were maintained throughout the third test. The wells on which the trials were made were not carried deep enough to test the resistance to solidification adequately, but oven tests at 350°F were made periodically and no tendency to solidification was noted except immediately after severe cernent contamination had introduced excessive amounts of calcium into the system. Although barium hydroxide costs considerably more than lime, the total mud costs were as low, and on the last well significantly lower, than the average cost of lime mud wells drilled in the vicinity. INTRODUCTION The advantages of repressing dispersion and hydra-tion of clay cuttings carried in the mud, particularly when drilling through thick clay formations, are well recognized. This repression is generally achieved by the use of lime, and lime muds have in consequence the desirable characteristics of high toleration of solids, low thixotropy, and good resistance to contamination. They have, however, the disadvantage of high-temperature solidification. This phenomenon has been described in detail by Gray et al, who have shown that it is the result of a chemical reaction between the hydroxides and the clay minerals. The work described in this paper was undertaken to find a substitute for lime which would not cause this solidification. LABORATORY EXPERlMENTS The principal positive requirement for a substitute for lime is that it should repress the hydration and dispersion of clay. It is well known that monovalent cations promote hydration while polyvalent cations repress it. Therefore, a few representative polyvalent salts and hydroxides were tested to determine whether they could be used as substitutes for lime. Their efficiency at repressing hydration and dispersion was measured by means of the clay-volume test. It has been shown elsewhere' that this test is a good measure of degree of dispersion of clay in suspension and that hydration accompanies and correlates with dispersion, so that measuring one measures the other. The test is made by centrifuging a 1:100 mixture of mud and 1-N NaCl and observing the volume of sediment—the greater the volume, the greater the dispersion. The tendency to caux solidification was measured by heating the muds in pressure vessels for 16 hours at 150°F and 370°F. An approximate quantitative

Jan 1, 1957

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By Howland Bancroft, Louis S. Cates

WE have come a long way since the order of the day was the chance discovery of mineral deposits, breaking rock with fire and water, melting metals in open fires in holes in the ground or in primitive furnaces, digging pits to collect. oil seepages, burning eroded coal outcrops to develop heat, and so on. During the past 5500 years, gradual improvements in methods and equipment have come about, explosives have been developed and used, steel has been used in increasing quantities and effectiveness as its physical and chemical characteristics, and composition have been altered and made to serve specific ends, hand equipment has given way to almost completely mechanized operation Thus, by the aid of mechanical equipment, one person is now able to move several thousand times as much material as one person was able to move a relatively few years ago. When this Institute was formed 75 years ago, the Suez Canal had been open to traffic but three years. It had taken ten years to complete and was built under the direction of French engineers by workers of whom many were girls. During the first four years of construction, these workers dug up the sand with their fingers, threw it into rush baskets, carried the load a hundred feet or so and dumped it 2 (With the termination of forced labor, dredgers completed the digging of the channel.) At the present time there is in use in the United

Jan 1, 1947

By E. E. McGinley, L. D. Woodworth

During the past several years has occurred what, in the light of future events, may aptly be called the rebirth of the acid Bessemer process. The increased attention given to the technical and metallurgical details involved in the production of Bessemer steels has been exceedingly fruitful, and indicates the value of further research and p1ant development. In times like these, when the steelmaking capacity of the country is operating at a maximum rate to supply materials for the national defense program, it behooves the Bessemer operator not only to strive to increase production but also to maintain a high standard of quality. The opportunity is ripe, it seems, to recapture fields of application once considered the birthright of Bessemer steels, but supplanted in recent years by open-hearth grades. This involves cooperation all along the line, from the blast-furnace operator to the metallurgical contact man and salesman. The metallurgist's part in this program involves the study of the many steelmaking variables and the measures necessary to ensure constancy in the finished product. It is equally important that the knowledge gained be disseminated widely to ensure the wise application of Bessemer steels in new fields. The merits of Bessemer steels for certain work are well understood. The combined properties of good weldability, machinabil-ity and stiffness are unique and fully explain the strong entrenchment of Bessemer steels in certain fields; e.g., skelp for small butt-weld conduit, screw steels machined in automatics, and certain tin-plate applications. It is the purpose of this paper to review briefly the physical properties of Bessemer steels as contrasted with those of open-hearth steels, to discuss control measures now employed in the making of Bessemer steel, and to consider the advantages derived from the use of these control measures. Physical Properties oF Bessemer vs. Open-hearth Steels A number of Bessemer blows and open-hearth heats were tested for tensile strength, ductility and impact strength. The steels selected were confined to sections from 3/4 to 1 1/4-in. diameter, inclusive, and the carbon content covered was sufficient to yield parallel ranges in ultimate strength for the comparison. Other factors, such as the extent of deoxidation of the steel and variations in chemistry, were kept as comparable as possible. Machined test pieces of 0.505-in. diameter with an 8-in. gauge length were pulled. The data obtained are shown in Fig. I, ultimate strength being plotted against carbon content. This graph shows that for equivalent carbon content Bessemer steel has on the average 15,000 lb. per sq. in. greater tensile strength and, conversely, for the same tensile strength Bessemer steel requires on the average 0.14 per cent less carbon. The average phosphorus content for the Bessemer steel was 0.090 per cent,

Jan 1, 1941

By J. Chipman, N. J. Grant, H. L. Bishop

In a recent review1 of the iron-oxide activity of simple open-hearth type slags containing lime, magnesia, silica, and iron oxide, it was established that activity values were lacking in the range of slag composition most interesting to open-hearth operators. That is, laboratory experimental results were not available for simple slag compositions having basicity ratios ranging from about 1.5 to 4.0 and iron-oxide concentrations ranging from about 10 to 30 pct. However, in order to estimate iron-oxide activities for the range of slag compositions of interest to open-hearth operators, activity values were calculated using ionic concepts of slags by following the treatment of Flood and Grjotheim.2 A study of these data indicated that the desired slag compositions were probably not obtained due to the limited solubility of the basic constituents lime and magnesia. Thus, it was decided to make additional heats equilibrating molten carbon-free iron with slags containing MnO, P2O5, and A12O3 in percentages commonly found in open-hearth refining slags, and to examine the liquid slag field over a greater composition range than that of the simple slags studied previously. The ranges of the constituents used in the present study are summarized as follows: Metal Pct 0 0.070-0.201 PctMn 0.005-0.142 Slag Pet CaO 24.45-41.90 Pct MgO 3.23- 9.21 Pct MnO 1.13- 9.62 Pct FeO 20.08-48.7 Pet Fe2o3 2.23-10.14 Pct SiO, 3.51-28.50 Pct P2O5 0.23- 3.65 Pct A12O3 0.43- 3.38 The experimental procedure consisted of equilibrating the slag and metal in an induction furnace provided with a carbon-arc slag heater as described previously by Winkler and chipman.3 The data obtained were used to establish both the iron-oxide activity values and the activity coefficients for FeO and MnO in the open-hearth type slags. RESULTS AND DISCUSSION I) Iron-Oxide Activity of Open-Hearth Type Slags—The iron-oxide activities of various iron-oxide contents of the open-hearth type slags, as calculated from the oxygen content of the metal by the method of Taylor and Chipman, 4 are plotted against the molar ratio of bases to acids in Fig. 1. The data represent slag-metal studies carried out in the temperature range 1530" to 1700°C. For the purpose of this study, the constituents CaO, MgO, and MnO are assumed equal on a molar basis in their effect on the iron-oxide activity; and, PO2,5 is calculated as an equivalent to SiO2 and A12O3 on a molar basis. The total iron content of the slag is calculated to FeO and is represented by the symbol (FeO) The points presented in Fig. 1 represent the results of this investigation for iron-oxide slags containing between 1 and 8 mol pct MnO and less than about 2 mol pct each of A12o3 and PO2,5 The curved lines shown in Fig. 1 represent the results of the summary1 of the iron-oxide activities of simple slags of the system (CaO + MgO) - SiOz - (FeO),. The solid portions of the curved lines represent experimental data, and the broken portions represent iron-oxide activities calculated from ionic concepts of slags. The iron-oxide values of the open-hearth type slags of this study are in good agreement with the values of the simple iron-oxide slag system. Only a slight modification is indicated. The results of this study suggest that the line for 20 mol pct (FeO), should be lowered slightly in the basicity range 1.5 to about 3.

Jan 1, 1959

By A. V. Bradshaw, R. I. L. Guthrie

The behavior of large bubbles in the size range 4 to 25 cm3, rising through molten silver, has been studied. It was found that rising velocities were equivalent to those in aqueous systems of low viscosity. Mass transfer coefficients for oxygen bubbles dissolving in silver were found to be 0.036 ± 0.007 cm sec-1, being close to those predicted for transfer through the front surface of the spherical cap bubble only. It is suggested that the surface active nature of oxygen in silver could account for the relatively low coefficients obtained. MANY metallurgical processes involve interactions between gas bubbles and liquids. Examples include the removal of carbon monoxide in Open Hearth Steelmak-ing, the removal of sulfur by blowing air through copper matte during converting, and the removal of hydrogen from steel during vacuum degassing or inert gas flushing. The steps involved in such refining processes include; transport of the dissolved species to the bubble interface, adsorption and chemical reaction of the species at the interface, desorption of product molecules from the interface, and transport of product gas into the bulk gas phase of the bubble. It has been concluded1 that all the interfacial steps involved proceed so rapidly at steelmaking temperatures that transport of the solutes, present in the metal, become the important rate controlling factors provided nucleation phenomena are not restrictive. The O-Ag system was chosen for the investigation into gas bubble-molten metal interactions due to the relatively high solubility of oxygen that enables rates of oxygen transfer to be measured from changes in bubble volume. Other advantages of this system include the absence of a stable oxide phase at an oxygen pressure of 1 atm and the relatively low melting point of the metal which permits the use of a metallic container, providing that it is resistant to oxidation. In those metallurgical processes where bubbles have an important influence, bubble volumes are usually greater than 5 cm3. For this reason the present study relates specifically to single large bubbles of oxygen rising in silver. These bubbles adopt the characteristic spherical cap shape similar to that shown in Fig. 1 for a 30 cc bubble rising in water. After an initial investigation to determine the velocities of inert (nitrogen) bubbles rising in molten silver, experiments were carried out with oxygen and the rates of mass transfer between the oxygen bubbles and the silver were measured. EXPERIMENTAL Apparatus. The apparatus, Fig. 2, for containing molten silver, was constructed from "Nimonic 75" Alloy (75 pet Ni, 20 pet Cr, 5 pet Fe, Mn) and provided for the release of single bubbles from an hemispherical cup, situated at the bottom of the column. The cup was turned by translating the rotation of the drive shaft through 90 deg. This was accomplished by the use of a bevelled gear system, and a smooth drive was provided by the lubricating action of the silver on the gears. Since reliable high temperature seals at 1000°C were found to be impracticable, the filling and drive shaft tubes were extended outside the 3.5 kw resistance wire tube furnace, where connections were made using easily accessible O-ring seals. The apparatus remained gas tight to the atmosphere at pressure differentials far in excess of those used. The filling tube was connected via a small bore tube to the differential pressure transducer. Gas could be bubbled into the inverted cup from two i-in. tubes which passed down the inside of the column to preheat the gas. The temperature of the silver was maintained at 1020°C during all experiments. Measurement of Bubble Volume. In order to calculate mass transfer rates, it was necessary to obtain a continuous record of the bubble's volume during its passage through the column of molten silver. The method adopted for measuring the bubble volume involved closing off the top gas space to the atmosphere prior to each experiment, and recording the variation in gage pressure of this space during the formation and rise of the bubble. Since any change in bubble volume results in an equal change in top space volume, Boyles Gas Law may be applied (for isothermal con-

Jan 1, 1970