Search Documents

By D. H. Polonis, M. B. Kasen

AN unusual thermal etching phenomenon has been observed on the surface of a Cu-Si alloy. The observations were made during studies of vacancy condensation pit formation which were reported in previous papers.1,2 Figs. 1 and 2 are photomicrographs of the surface of a Cu-4.8 pct Si alloy after heating in vacuo (3 x X mm Hg) to 525°C and subsequently holding at that temperature for 16 hr in an impure (air-contaminated) argon atmosphere. Under these conditions preferential removal of silicon from the matrix by oxidation results in a surface which is entirely a phase overlying an a plus y structure. The light areas of Fig. 1 are regions in which very little thermal etching has occurred, while the majority of the surface has experienced severe etching. Similar regions in Fig. 2 are seen as plateaus above contours produced by net transfer of material from the specimen surface. Twin boundaries are also visible in Fig. 2. The difference in matrix mi-crostructure between Figs. l and 2 reflects the par- ticular orientation of low-index planes with respect to the surface of observation. Thermal etching contours of this type have been studied in detail by Hondros and Moore Both of the photomicrographs show that one or more dark spots are located approximately at the center of every protected area; where two spots are in close proximity, the protected areas have merged. The microstructures indicate that the anomalous resistance to thermal etching is related to the presence of these spots. Williams and Hayfield have shown that local regions of unusually high oxidation resistance can be caused by a surface monolayer of atoms with a work function higher than that of the base material. The result is an inhibition of the rate of electron removal from the base material and a decrease in the oxidation rate. The source of the protected layer may be either surface diffusion from contaminants on the specimen surface or pipe diffusion of solute atoms followed by migration across the surface. In the latter case the driving force is a difference in chemical potential resulting in a Gibbs adsorption phenomenon. In the present case, chemical polishing of the specimen surface precluded contaminants of a strictly surface nature. Consequently, diffusion of impurity atoms from within the lattice appears to be the most tenable explanation of the observed phenomena. The authors propose that the structures of Figs. 1 and 2 reflect the diffusion of impurity atoms along extended dislocations within the individual a phase grains prior to surface oxidation. The central spots within the protected regions are seen as sites of dislocation emergence which have become locally decorated with oxide in the manner discussed in Ref. 1. Williams and Hayfield observed protected regions adjacent to the grain boundaries of iron-contaminated copper which they attributed to the segregation of iron to the grain boundaries coupled with high dif-fusivity along the complex dislocation array at such boundaries. No evidence of such grain boundary protection was observed in the Cu-Si alloy; this

Jan 1, 1964

By D. C. Jones

THE term "coal-mine mechanization" is definable in several ways. In its general application it can mean the use of machines instead of manpower in each of the various mining activities necessary for the produc¬tion of coal-so that under this definition a mine that uses mechanical coal cutters could be classed as a mechanized mine. Common usage, however, insists that a mechanized mine is one in which machines are used for the entire process of mining or extraction and transportation of the coal. For the purpose of this paper, then, the second definition of "coal-mine mecha¬nization" will be used, and practices employed in mines where the greater part of the production is obtained through the use of mechanical loaders and conveyors will form the basis for this discussion. PHYSICAL CONTACT HAZARDS If we were to group all the hazards that accompany the use of mechanized equipment in a mine, the predominant class would be that which, for want of a better name, might be termed the "physical contact" hazards; that is, all the sources of danger that lead to accidents through physical contact of workmen with ma¬chines. A survey of accidents in a group of mechanized mines indicated that this class of hazards may be responsible for more than half the number of accidents in mechanized mining. For example, of 21 mining-machine accidents at one mine, 14 were of the physical contact type of 14 loading-machine accidents at the same mine, 8 were the result of physical contact. Certain of these hazards an controllable through the use of guards-¬a guard over the cutting-machine bits whet the machine is being trammed from place to place, or a chain or some similar locking device around the cutter chain, so that an accidental blow or push against the bit control will not cause the cutter chair to move. Other hazards, such as the possibility of. a loader operator having hi foot crushed by a crawler tread, or , brakeman being hit by a loader boon swung too far to one side while a car is being loaded, might be subject to control through the use of guard devices, but the reduction or elimination of all physical contact hazards by such methods doe: not appear feasible. Every accident of the physical contact type should be investigated to discover whether guards could have prevented it, but often the only way in which to combat these hazards will be through the awakened consciousness of each workman as to the danger that exists if he indulges in unsafe practices. A good approach to control of accident: in any mine is the establishment of a set o: safety rules or operating rules. The intent of such rules is to provide guides for the workmen to follow in the operation of equipment. Frequently the workmen have no regard for such rules, and observance is obtained only through compulsion or the part of management. An interesting development in connection with the formation of safety rules occurred during a training program for employees in the

Jan 1, 1946

By John A. Emery, Frank G. Snyder

MINING geology has a threefold objective: to guide prospecting for new ore, to evaluate known orebodies as development risks, and to supply the detailed knowledge of ore structures necessary for more economical extraction. The role of geology in exploration is well established. This article will deal solely with orebody evaluation and the application of geology to development and mining problems as practiced by St. Joseph Lead Co. in the southeast Missouri district, which for many years has supplied approximately 30 pct of U. S. lead production. The primary concern of the present discussion is geology in the district, not geology of the district. The southeast Missouri district, locally called the Lead Belt, includes parts of St. Francois, Madison, and Washington counties. The first recorded mining was about 1720 at Mine La Motte in Madison County on surface showings of lead ore. Later discoveries near Bonne Terre, twenty-five miles to the north, led to extensive prospecting and underground mining. To date the district has yielded well over 8 million tons of pig lead, valued at more than $1 billion. By far the greater part of the lead production has come from an area of 50 sq miles, centering on the city of Flat River, as shown in Fig. 1. Role of Geology in Metal Mining The history of the use of geology in the older metal mining districts follows a simple consistent pattern that may be considered in terms of four distinct phases. Each geologic phase is a response to the economic status of the mining district; each has definite characteristics setting it apart from other phases; and each passes into the succeeding phase as the mining operation gradually exhausts the large, rich, easily discovered deposits and lives upon increasingly smaller, lower grade orebodies that are less easily found. The geologic phases and their major characteristics are as follows: Period of No Organized Geologic Program: During the early history of a great metal district ore is easily found by random prospecting and wildcat drilling. Many small operators are active, as profitable mining can be done with a relatively small capital outlay and a minimum of technical staff. Mining practice consists largely of sinking a shaft on an ore showing and following the ore in sight. When the ore is exhausted or becomes unprofitable to mine, the process is repeated on a new ore showing. The miners become familiar with certain ore habits and use this practical geologic knowledge to guide mining. The method is successful as long as large tracts of virgin mineralized area are available. This phase ends when small-scale mining methods are no longer profitable and the mines become consolidated into the hands of a few operators.

Jan 1, 1957

By J. B. Austin, R. L. Rickett

Measurements of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage transformed on linear coordinates against time on either a linear or a logarithmic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even intebrpolation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolatiorr is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valuable when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decomposition of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1939

By Harry W. Antes

The density changes that occurred on annealing cold-worked poly crystalline molybdenum, over the temperature range of 870" to 1630 SC, were determined. Increases in density were observed for recovery and the beginning of recrystallization. An initial decrease in density was observed during re-crystallization. A second decrease in density was observed after recrystallization was completed, as the microstructure changed from columnar grains to equiaxed gvains Both decreases in density were associated with an increase in gain boundary area to volume ratio. The second decrease in density was observed in the annealing range that immediately precedes secondary recrystallization as reported in the literature VARIOUS techniques have been used to identify the recovery, recrystallization, and grain growth processes that occur when cold-worked metals are annealed. As early as 1928 work was conducted that indicated measurable density changes occur when cold-worked single crystals of brass are annealed.' More recently, work by Murphy exhibited a corre- lation of density with microstructural changes observed on annealing cold-worked polycrystalline a brass.2 Other investigators have performed similar work on a brass and copper.324 In reviewing the literature, it was apparent that density work had been limited to fcc materials. Therefore, it was the purpose of this investigation to determine the density changes that accompany annealing the cold-worked bcc material, molybdenum. Two degrees of cold work, 30 and 90 pct reduction of cross-sectional area by rolling, were selected for this study. EXPERIMENTAL PROCEDURE High-purity vacuum arc-cast molybdenum was used in this study, the principal impurity being carbon in the amount of 80 ppm. The final rolling reductions were made at 1200°C in grooved rolls to provide 5/8-in.-diam rod. Density specimens 0.500 in. diam by 1.5 in. long were machined from the bar stock. The specimens were ground to the final dimensions to provide a smooth surface. Density measurements were made using a hydrostatic technique similar to that used by ~urphy.' This type of equipment permitted weighing in liquid immediately after the air weighing. During each weighing the temperature of the air and liquid was controlled to within 0.0l°C. This was accomplished by sealing the analytical balance in an air-tight brass chamber and surrounding it by an insulated wooden case. Preheated air was circulated in the air space between the brass chamber and wooden case by means of a blower. The temperature of the

Jan 1, 1964

By R. A. Perry

A speiss is an artificial arsenide, sometimes an antimonide, formed in lead smelting, smelting of oxide copper ores, and in some lead-refining operations. The production of speiss is closely allied with the amount of arsenic and metallic iron in the blast-furnace charge, while dross is produced mostly from the copper and sulphur, with varying amounts of antimony, arsenic and nickel. Most speiss is essentially an iron arsenide containing some sulphur, copper and nickel, if these elements are present in the furnace. The recent introduction of the soda treatment of lead drosses has produced a speiss high in copper. Speiss is not miscible to any extent with molten copper, lead, matte or slag. Miscibility increases with temperature. This property of the speiss is clarified in the latter part of this paper. Most speisses are produced in conjunction with matte and their sulphur content points to the solubility of matte in speiss. . Some plants have insufficient speiss to warrant separate treatment. When arsenic is high in the blast-furllace charge, there may be sufficient speiss to tap separately from the first settler. Arsenic From the foregoing, it is obvious that a study of the treatment of speiss would not ,be complete without consideration of arsenic. Inasmuch as perhaps go per cent of the blast-furnace feed may be sinter, a definite knowledge of the properties of arsenical ores and compounds that go in to the roaster and sinter feeds is of value. Lcad smelters obtain their arsenic from ores and concentrates, as well as from flue dusts shipped from other plants, particularly copper smelters. The percentage of arsenic in ores is usually low, although occasional lots of high arsenical products are smelted. These crude ores may be sulphides, as arsenopyrite; or oxides like scoiodite, which carry gold or lead minerals. The small amount of arsenic in the original ores received is greatly increased by a circulating load of arsenic in secondary products at are resmelted for their lead or precious metals. More important than the arsenic present directly in the concentrates treated is that in fumes and dusts that may originate in the blast furnace or sinter plant of the lead smelter, or may come from a copper smelter as lead-bearing converter fume or roaster dust. Thus the lead smelter not only must treat its own arsenic but is compelled to handie that from some copper and perhaps other lead plants. Where copper and lead plants exchange products, each plant may be forced to re-treat part of the arsenic it has shipped ,outside its own confines. Speiss from the lead blast furnace contains chiefly iron and arsenic with some lead, copper and sulphur and often appreciable amounts of gold and silver. If its copper content is sufficient this speiss may be sent to the copper smelter where usually it is treated in the converter and the copper is separated as blister. Much of the arsenic and most of the lead are recovered as converter fumes

Jan 1, 1944

By Jim Douglas, H. H. Rachford, D. W. Peaceman

The problem of unsteady-state gas flow through porous media has been solved numerically only for the case of linear or radially symmetric reservoirs. A recently introduced numerical method for solving the unsteady-state heat flow equation in two dimensions is applied to the calculation of the depletion of a square region containing a perfect gas. Solutions are presented in graphical form for various values of dimensionless parameters. The solutions are compared with published .solutions for radial reservoirs. I NTR ODUCTION The problem of unsteady-state flow of gas through porous media gives rise to a second-order non-linear partial differential equation for which no analytical solution has been found. Numerical approximations to solutions of the gas flow problem have been obtained by the stepwise solution of an associated difference equation1,2. However, the methods so far developed have required that the reservoir be either linear or radially symmetric. This restriction in shape has been necessary so that only two independent variables be considered, namely, one distance variable and time. In order to deal with reservoirs having more realistic shapes, it is necessary to develop numerical procedures for the solution of the gas flow problem involving two distance variables. A numerical procedure, denoted as the alternating-direction implicit method, for the solution of the heat-flow problem in two dimensions has recently been introduced" By the use of this procedure, approximate solutions have been obtained for heat-flow problems in a square8, and in regions having various non-rectangular boundariesa. Because of the similarity between the equation for heat conduction in solids and the equation for gas flow in porous media, it is reasonable to expect that the alternating-direction implicit method should also be useful for solving the gas flow problem in various two-dimensional regions. Solutions have been calculated for the simplest two-dimensional region, a square reservoir with a single well in the center. While reservoirs of such simple geometry seldom, if ever, exist, the solution of this problem is of some practical importance because it is also the solution of another problem, that of determining the depletion history about an individual well in an infinite uniform reservoir containing wells spaced throughout on a square lattice and producing equally from each well. Finally, it is of interest to compare solutions for a square reservoir with those for a circular reservoir and to determine the effect of the shape of the boundary for that particular case. METHOD OF CALCULATION Basic Differential Equation By combining the equation of continuity, the perfect gas law,

Jan 1, 1956

By John E. Miller

Unit Rig & Equipment Co., manufacturer of Lectra Haul trucks, is continually studying methods of reducing the operating costs of large haulage trucks. Reduction of haulage system operating costs is an important goal that equipment operators and equipment manufacturers constantly try to improve on. One of the most variable and important factors affecting operating costs is actual truck operating practices. An examination was centered on methods to optimize truck utilization. It was found that a very effective method of accomplishing this goal would be an automatic truck control (ATC) system to automatically control a fleet of haulage trucks in a predetermined pattern. Economic studies were conducted which showed a very favorable reduction in mine operating costs by use of an ATC system. In 1970, Unit Rig & Equipment Co., in conjunction with SAAB-SCANIA began preliminary development of adapting, for truck use, a proven automated control system, previously used for train systems, small trucks, and military target vehicles. In 1974, the first prototype system was installed on a Lectra Haul M-100 and tested extensively at Unit Rig's test track in Tulsa, OK. This truck and system were then displayed publicly at the 1974 convention in Las Vegas. In 1976, the system was redesigned for production to maximize reliability, ease maintenance, and to accommodate future control and-status reporting developments proposed for haulage trucks. The new design equipment was manufactured, and a full system test will be conducted in an actual open-pit mine for an extended period to evaluate reliability, compile economic data, and obtain application information to evaluate complete mine haulage system conversions to ATC. System Description The ATC system is designed to provide automatic control of all the vehicle functions normally accomplished by the vehicle operator. The basic system consists of the on-board control equipment and the wayside control equipment. The on-board equipment receives commands from the wayside equipment and controls all the truck functions. In addition, on-board sensors monitor all critical truck functions and provide instructions to the truck and system to assure safe operation. The wayside equipment consists of a buried guidewire, block control units and a central controller which provides predetermined signals to the on-board equipment for speed control, steering, and for auxiliary functions (dumping, horn, etc.) through the guidewire located in the truck's path. The wayside equipment also controls vehicle separation, system status, and provides truck location to a central display panel. The central control panel can vary the speed level signals over any segment and can also command an emergency stop to halt all the units. [Fig. 1] illustrates a typical ATC installation. If ATC is used in operations which require flexibility and mobility at the end of the ATC guidance network, the trucks can then be operated by either radio remote control or manually to complete their assigned functions.

Jan 1, 1982

By Leonard D. Jaffe

IN recent years, the advantages of tempered martensite as a microstructure for steel parts have been well established. For parts that must not fracture brittlely when loaded at high rates, at low temperatures, or under conditions of combined stress, tempered martensite is especially desirable. One of the factors that determine whether a steel part will have a martensitic structure after heat treatment is the hardenability of the steel. Despite the large amount of recent research, there are still many unsettled basic questions concerning hardenability and its relation to chemical composition, and, indeed, considerable disagreement among investigators in the field. Much of the uncertainty that beclouds the existing knowledge of hardenability arises from the fact that hardenability is still a wholly empirical concept, and has not been quantitatively related to the more fundamental knowledge of isothermal decomposition of austenite. Hardenability is, essentially, a measure of the time required for small percentages of austenite to decompose, during continuous cooling, to pearlite, bainite, proeutectoid ferrite, or proeutectoid carbide. In the practical heat-treatment of steel, also, the decomposition of austenite is usually not isothermal but rather during cooling, or, in general, is not at a single constant temperature. Thus, both hardenability and practical heat treatment involve anisothermal decomposition of austenite. In a previous publication1 the author and his collaborators outlined the principles that govern the relations between isothermal and anisothermal decomposition of austenite, and reviewed the experimental information available in 1945. To avoid repetition, familiarity with that article (Paper 1) will be assumed, and attention given primarily to work carried out or published since 1945. The method generally employed was explained in Paper 1: anisothermal transformation is studied through investigation of the effect of holding austenite at one temperature upon its subsequent decomposition at another temperature. Both temperatures are below the stability range of the austenite. This paper is confined to studies in which only a small amount of transformation occurred at the first temperature. This is the only case of importance in practical heat treatment when an essentially martensitic structure is sought. MATERIALS AND PROCEDURE It was necessary to use different steels for the studies involving proeutectoid ferrite and for those involving proeutectoid carbide, because the two constituents have not been found to form in the same steel. Several steels were tried and rejected

Jan 1, 1947

For the use of future students the following notes on the times of completion of various railroads and canals supplying transportation to coal fields are set down. These dates are widely scattered and sometimes difficult to find. A statement showing the mileage of railroad building from 1830 to 1879 by each railroad in the United States is given in the 10th U. S. Census, 1880, vol. 4, pp. 318-365. [Date of Opening Various Bituminous Districts by Railroad Transportation1 Blossburg, Pa. district in1840 Georges Creek, Md. district in1842 Broadtop, Pa. district in1856 Clearfield, Pa. district in1866 Meyersdale, Pa. district in1872 C. & 0., W. Va. district in1873 Elk Garden, W. Va. district in1881 Pocahontas, Va. & W. Va. district in1883 Beech Creek, Pa. district in1884 Hocking Valley, 0. district in 1869.-by Canal 1840] See also Paullin's Atlas of the Historical Geography of the U. S., published by the Carnegie Institution of Washington, 1932, for small-scale maps showing railroad development by decades. [OHIO CANALS Date Date CompletedName of CanalFromToAbandoned 1827, July 4Akron Cleveland 1827, Nov. 28Cincinnati Middleton 1828, Dec. 31 Cincinnati Sandusky 1830, July 10 Cleveland Newark 1832, Dec. 31 Akron Portsmouth 1838Penna. & Ohio Akron Pa. Canals 1853 north of Pgh. 1840, Sept. Hocking Valley Columbus Nelsonville 1844 Sandusky Dayton 1846 Sandy & Beaver Bolivar Smith's Ferry 1852 1846 Cincinnati Springfield]

Jan 1, 1942

By J. Chipman, J. C. Fulton

Reduction of silicon from blast-furnace-type slags by carbon-saturated iron is a very slow reaction even under conditions of rapid stirring. Equilibrium under atmospheric pressure of carbon monoxide was approached from both sides, and the silica-silicon relation was established at temperatures of 1425º to 1700°C for slags containing up to 20 pct Al2O3. Silicon carbide is formed by reaction of graphite with high silica slags and the conditions for its formation were determined. Activities of SiO2 and of CaO in their binary solutions at 1600°C were determined. The effects on the activity of SiO2 were established for additions of 10 to 20 pct AI2O3 and of 10 pct MgO. STUDIES of chemical reactions between blast-*>-5 furnace slags and metal have been focussed on the transfer of sulphur from metal to slag. The important role which silica reduction plays in this process' has led to a study of the transfer of silicon from slag to metal and the equilibrium represented by the equation SiO2 (in slag) + 2C (graphite) = Si + 2CO (g). [I.] The authors2 have published an account of the experimental method employed in attacking this problem and of three series of experimental results at 1600°C. This paper contains data on some additional compositions and extends the observations to cover the temperature range 1425° to 1700°C. The data are used to determine the activity of silica in the slags. As in the earlier experiments, the atmosphere was carbon monoxide which flowed through the furnace at 150 ml per min. In certain heats designated in the tables and figures, the gas was bubbled through the melt using a graphite tube. The latter increased in porosity during a run and in some cases bubbling ceased as indicated by cessation of surging. Some results were discarded for this reason. Experimental Results The new data are shown in Tables I through V and both old and new data are plotted in Figs. 1

Jan 1, 1955

By J. F. Wolff

EXPLORATION of Lake Superior iron ores is done principally by drilling. The soft iron ores are churn drilled and the harder ores are diamond drilled. In exploratory work in the harder formations, where the diamond drill is used, the sample comprises both core and cuttings. The care given in handling and preserving the core depends on the im-portance that may be attached to certain characteris-tic strata in different formations. The following instructions for the care of core samples are issued by the Oglebay Norton Co. for diamond drill work done for them on the Gogebic Range of Michigan: The driller shall be careful upon removing the core from the core-barrel to keep the core in exact order. Not only should the pieces of core be kept in exact relation to each other, but care should be used not to turn them end for end. Core should be placed in the core-box from left to right in each row. Each drill should be furnished with small, hinged cover core-boxes, and each drill should be well supplied with empty boxes. Core remaining at the drill when the drillers are not working should be locked up. The practice of picking sample pieces of core and carrying them away from the drill to be examined in better light, or shown to someone else, is unnecessary and prohibited. The reason for this is that these pieces are seldom returned to the core-boxes and valuable information or "markers" may be lost. If the inspector suspects that a critical point is reached in the drilling and he cannot determine at the drill, he should remove the entire core-box and see that the drill is immediately furnished with an empty core-box. It is customary to split the core longitudinally so that one-half may be ground to a pulp for analysis and the other half may be kept for future inspection. The core should be filed in permanent core-boxes, properly labelled, if the core is to be kept in exact order as taken from the core-barrel. Otherwise, it is often filed in tin boxes inn the way that sludge samples are filed. To obtain the average analysis, the core and cutting samples obtained in the same run are analyzed separately and the analyses are combined in the proper ratio.

Jan 9, 1922

By Ilmar Stöckel, Gösta Harlin, Agne Rustan

INTRODUCTION This chapter is a continuation of the studies by Rustan and Stockel (1979, 1980) on techniques for automating ventilation in Swedish mines and construction works. The studies have been financed by the Swedish Board of Technical Development. As a result of the studies it has been recommended that a good solution to diesel exhaust emission would be automatic, step by step control of the fans near the working place. Diesel vehicles are the major polluters underground in the mines. Therefore, we have suggested that diesel vehicles regulate the fans The goal of the continued study has been to find a way for active diesel vehicles to start and stop gallery fans at both intake and return air. In this paper different methods for activating fans are discussed. The best methods are chosen and tested in the mine. In this study we have found that change of temperature is an inexpensive and effective way to start and stop crosscut fans in sublevel caving and radio signals seem to be an attractive system for starting and stopping gallery fans . This work has been done in close collaboration between LKAB in Kiruna and the University of Luleå, Divisions of Electronics and of Mining and Rock Excavation. An advisory group for the project has been established with ventilation experts from the mines, representatives of the local mine workers' unions, and authorities from the local offices of Governmental Inspection of the Workers Safety. VENTILATION SYSTEM STUDIED In the project the ventilation system at LKAB in Kiruna was studied. The mining method used is sublevel caving with 9-13 m slice height. The air above ground is heated in winter by hot water and the main fans push the air down to a main distribution level along the 4000 m long and about 100 m wide ore body. From the distribution level, air is taken through shafts down to the sublevels, where it is pushed through the levels by local gallery fans on both the intake and return sides, Fig. 1.

Jan 1, 1981

JULY was a month of great turmoil, both economic and political, in many parts of the world. Instead of conditions improving, they seem to have been getting worse. In Ireland, civil war is still in progress. Germany was in the throes of a political upheaval. The meaning of the assassination of Rathenau became clear. It evinced the development of a class struggle between the bourgeois and socialistic parties which may rock the country to its foundation and will increase the difficulties of arranging things with the French and solving the reparations problem. In Poland, a similar contest is developing. Austria is already so completely contaminated by the socialist element that it is unable to get outside assistance and is thus falling into a state of despair but little short of what prevails in Russia. The conference at the Hague came to an abortive end for the reason that it was impossible to discuss affairs with the Russians in any reasonable way. The Germans declared their inability to meet the reparation payment that fell clue on July 15 and the Commissioners for the Allies granted them an abate-ment of a portion thereof and are listening attentively to the supplication of the Germans for a moratorium of one or two years. In the United States, July was a month of widespread labor troubles, accompanied by a great deal of disorder and violence, which led to detachments of the National Guard being called out in several states. The railway shopmen, about 400,000 in number, struck on July 1. The road maintenance men decided not to strike, but many thousands of them quit work without the sanc-tion of their union. There were more strikes in the textile industry in New England and in similar industries all over the country. Early in July, it was estimated that about 1,250,000 men were out on strike. The coal strike continued. Early in the month the President summoned operators and miners to Washing-ton and submitted a plan for the compromising of disputes. After a week's consideration the miners re-fused flatly to agree to anything. The majority of the operators consented to accept the proposed arbitration, but a minority refused. Following this abortive at-tempt the President dismissed the conference with the injunction "to return to your mine properties and resume operation." Production has not increased.

Jan 8, 1922

By Martin A. Mayers

It has long been recognized that it would be highly desirable to be able to predict the temperatures at various points in a burning fuel bed and their variations with changes of the properties of the fuel and the rate of air supply. Experimenta1 investigations of fuel-bed temperature1-4 have not been lacking, but the absence of any theoretical background has made it impossible to use the results of these tests as a basis for prediction, except in a very general may. A mathematical analysis", based on a somewhat simplified theory of the distribution of lieat in a fuel bed, lias recently been completed by the author. Even though numerical values of some of the coefficients are not known, the calculations result in some conclusions of general significance. Thus, for example, it appears that when the temperatures throughout the fuel bed can be calculated, the rate at which ignition of the fuel by underfeed action can be maintained can also be calcu1ated. The uncertainty concerning the values of the coefficients referred to above is serious limitation on the use of that method. The following paper presents a discussion of these coefficients and includes estimates of their values based on the data now available. A brief description of the theory on which the analysis is based, and some results of the calculations showing their degree of agreement with experimental results, are presented by way of introduction to the discussion of the coefficients. For a more. extended discussion of the theory, see the A.S.M.E. paper5. Theory and Comparison with Experiment The theoretical analysis is similar to that used in the calculation of the stationary temperatures in a conducting solid in the classical theory of heat concluction. The fuel bed is pictured as a uniform, continuous, porous solid through the interstices of which air can be blown and ill which combustion can take place. The solid lias a finite thermal conductivity, so that heat may be transported in any direction, against the flow of air as well as in the same direction. While it is true that nothing

Jan 1, 1938

By S. H. Penn

Preliminary experimental evidence seems to preclude the use of unlubricated mechanical force drills on the moon. Measured values of the coefficients of friction and adhesion between metallic and nonmetal-lic solids have been shown to increase in an ultra-high vacuum environment. The paucity of real knowledge of the influence of a hard lunar vacuum upon interacting solid surfaces, relegates current proposals to sample the moon with a mechanical force drill, to the equivalent of wildcatting on earth. Within a few years, drilling will be attempted on the lunar surface with tools that have been designed with parameters that are normally considered for most conventional terrestrial drills. Lunar drills must be light in weight, portable, have reasonable penetration rates, low manpower requirements, etc. Although the initial equipment cost is expected to be high, this will probably not be a critical factor. Early lunar drilling will be limited to shallow holes with depths of 10 ft or less. The primary function of these holes will be to furnish samples of lunar surface materials but they may also be utilized for other purposes, such as geophysical experiments. Instruments may be installed in them capable of measuring thermal diffusivity, gamma radiation, etc. As sampling will be the primary objective of the earliest holes, sample contamination is a parameter that effectively excludes such otherwise promising techniques as explosive or plasma jet drilling. The most desirable method is probably some form of mechanical force drilling that has the capability of operating in the extreme lunar thermal environment (125° to 37S°K), high vacuum (10- l3 torr range), and low gravity.

Jan 1, 1968

By Howard A. Smith

OF late considerable experimental and theoretical interest has been shown in the rates of transformation from a single phase, usually a supercooled solid solution, into one or more phases. Such reactions may involve both diffusion and transformation of the major constituent, as in iron alloys, or it may simply involve diffusion, as in superstructure formation and in age-hardening systems. Most of the work has been confined to ferrous alloys1-9† although two investigations have been made on copper alloys 10-11. That such work may be of considerable practical importance has been demonstrated by Bain12, by the workers at the Kaiser Wilhelm Institut für Eisenforschung13, 14, and by the everyday use of precipitation and age-hardening principles15. Experiments in this country have generally followed Davenport and Bain's technique of rapid supercooling followed by isothermal treatment. In Germany16, 17 the work has been extended to the study of the influence of accurately controlled and measured rates of cooling. The work on steel indicates that there are two subcritical temperature ranges where reaction starts sooner after quenching and proceeds at a more rapid rate than at other temperatures. At subcritical temperatures above Ar" where reaction is dependent upon atomic migration there is a period of time of which the length depends upon the alloy content and the temperature, before which no reaction has been detected. Davenport and Bain1 find that different sorts of atoms in solid solution in gamma iron affect the length of this "prereaction" period differently, manganese

Jan 1, 1935

By E. W. Dewing

The solubility of A14C3 in cryolite melts has been determined by holding the melt with aluminum in a graphite crucible for 4 hr at temperature, quenching the crucible in water, and analyzing the frozen salt by CH4 evolution. The solubility is given by log(wt % Al4C3) = 1.298 -1.l74 (wt ratio NaF/AlF3) independent of temperature in the range 985" to 1080°C. Additions ofA1203, .NaCl, CaF2, or LiF up to 10 wt pct do not affect the solubility, provided that LiF and CaF2 are replaced by equivalent NaFin calculating the ratio. The variation with ratio can be accounted for quantitatively on the hypothesis that the Mechanism of solution is Al4C3 + 2AIF3 = 3Al2CF2 since the solubility varies as (aAIF3) 2/3; Mechanisms involving C", C2- , AlC- , A12C2+, and Al2CF+are re-jected. At ratios above 1.5 truces of c;- are also present. It was noticed some years ago in this laboratory that carbon specimens made cathodic in a cryolite bath decrease in diameter over a period of time.' It was also found that cryolite which had been melted with aluminum in a graphite crucible was sometimes yellow, and that A14C3 could be seen intimately embedded in the cryolite crystals. CH, could be recovered by acid attack. There was thus reason to believe that A14C3 had a genuine solubility in molten cryolite, and the object of this work was to measure it. EXPERIMENTAL AND RESULTS A graphite crucible, 2 in. ID and 2.5 in. deep with a close-fitting lid, contained about 150 g of cryolite (plus additives) and about 20 g of 99.99 pct pure Al. It was placed in a vertical Inconel furnace tube, covered with refractory brick to provide thermal insulation, and the top of the tube was roughly sealed with disks of asbestos paper. An alumina tube led argon down to the level of the top of the crucible to expel air, and an alumina sheath with a Pt-10 pct Rh ther-mocouple inside was positioned between the crucible and the wall of the Inconel tube. The tube was heated in an electrical resistance furnace for the desired length of time; the refractory bricks were then removed, and the crucible was lifted out with tongs and quenched in water. After such a crucible was broken open it could be seen that its inner surface was yellow owing to the presence of A1,C3, and sometimes needle-like crystals could be observed (at X75 magnification) growing out into the nielt. It was concluded that Al,C, had been present as a separate phase when the crucible was at tenlperature and that the melt had been saturated: in

Jan 1, 1970

By H. R. Peiffer

Composite alloys of silver and alumina are shown to resist flow above the melting point of the continuous matrix. The ability to resist flow depends on the fineness of the dispersion and the oxygen content of the silver. It is believed that the oxygen influences very strongly the bond between the molten silver and the finely divided alumina. RECENT needs for materials with high strength and creep resistance at high temperatures initiated mechanical property studies on dispersed phase materials to near the melting point of the continuous matrix material. Results' of these investigations have shown that certain of these materials do have promise for high-temperature applications. Experiments performed on composite materials of silver and alumina by the author have resulted in the discovery of an interesting effect above the melting point of the silver. In these materials the silver was continuous and the alumina very finely divided (Linde B). It was observed that these materials exhibited strength and resistance to flow above the melting point of the silver matrix. The purpose of this paper will be to describe these properties. METHOD OF PREPARATION The materials were prepared by mixing the proper amount of Linde B alumina and high-purity silver oxide. The alumina content was varied from 5 to 20 wt pct alumina in silver in 5 pct steps. The materials were mixed by blending the constituents in an ordinary food blendor using ethyl alcohol as a vehicle. Enough alcohol was added to the powders to form a mixture with the consistency of a thin mud. After blending for about | hr the material was dried and the silver oxide reduced by heating to 450 OC. The material was then pressed at 25 tsi into a -in. billets 3 in. long. EXPERIMENTAL PROCEDURE The specimens were horizontally supported at either end by knife edge supports of cold-rolled steel. This holder was then placed in a "globar" furnace and a chromel-alumel thermocouple placed very close to the specimen recorded its temperature to within 10°C. Each specimen was heated rapidly to 900°C initially. The specimens were held at temperature approximately 30 min and then the temperature was raised 50 deg. The procedure was repeated until deformation was noted. Photographs were made of the specimens at various temperatures and increments of time using a Polaroid Land camera. RESULTS Fig. 1 shows the 5 pct by weight "Linde B" alumina and silver material after reaching 980 °C. Failure occurred after 15 min at this temperature. There were two points of failure and silver collected at them. No additional flow of the molten silver was noted at any other place. Fig. 2 shows a 20 pct by weight "Linde B" alumina in silver specimen. After 30 min at 1400°C, bowing of this material was observed. Other concentrations of alumina were added to

Jan 1, 1961

By Raymond M. Howe

Some time ago, a prominent engineer asked a representative of the firebrick industry to prepare a comprehensive paper on blast-furnace refractories. It was to have been the purpose of this paper to gather practical experiences from widely different sources, in the hope of determining what kind or kinds of firebrick were best adapted for certain uses. This engineer sent questionnaires to the large consumers of blast-furrace linings and stovebrick and received very detailed replies as to their experiences. These replies are conflicting, but, having been turned over to the writer, form the basis of this attempt to meet the request. Because of the impossibility of making final recommendations at this time, a few of the more interesting and commonly known methods of studying refractories are also discussed, as well as the more recent developments in this field. The first reply to the questionnaire stated that good service was being secured from the linings. This satisfactory condition was attributed to the use of a very good distributor. The writer believed that manufacturers try to and do produce a good product and that the proper handling of equipment is of the utmost importance, if good results are to be secured. The type of bricks used was not mentioned. The second reply stated that good life was secured from the furnace linings, but that the writer had had soft-fired stovebrick crumble and, for that reason, preferred a hard-fired product for use in this position. The type of bricks used was not mentioned. The third reply stated that firebrick had crumbled from the mantle up; the cause was not known. The fourth reply stated that the stove linings were satisfactory. Hand-made furnace linings failed after.4 years' service so a steam-pressed lining- was installed which was still good after 4 years of service. Consequently, a second steam-pressed lining was installed but this disintegrated at the top after the furnace had been in blast 7 months. The firebrick manufacturer attributed this failure to the expansion of iron blocks that had been installed at the stock line to prevent erosion. The fifth reply stated that the present "hard-burned" hand-made furnace lining had worn away very uniformly to the depth of only 5 in.

Jan 1, 1920