Search Documents

By R. D. Nelson, F. E. Bowman

Assumptions are made of ideal mixing and that the density of silver can be obtained by extrapolating reported liquid density-temperature data through the freezing point back to the temperature range of interest. The results of this procedure using liquid silver density data of Kirshenbaum et al.5 are presented in Table I1 where it is observed that agreement is everywhere within <0.1 pct and generally is within 0.05 pct. Because the Sn-Ag alloys are dilute, the assumption of ideal behavior is, therefore, probably justified. In conclusion, the densities of dilute liquid solutions of silver in tin have been determined. Even for concentrations as low as 0.1 pct, the effect of silver on the density of liquid tin is clearly measurable. This work also suggests that for dilute alloys at temperatures far below the freezing point of the solute metal, densities may be accurately calculated by extrapolation of the pure metal data without having recourse to physical measurement on the alloy itself. plutonium having a grain size of about 100 µ. This paper presents data showing that large elongations of fine-grained a Pu can be obtained by using slow deformation rates. Large plasticity, however, of a Pu in compression has been observed.4 Reductions in thickness of 90 pct have been observed with no edge cracking. These large reductions are accompanied by concurrent re-crystallization. The deformation modes, which are quite complex, have been studied extensively by observing the deformation microstructures of polished surfaces that had been deformed in compression.5-7 Although slip apparently is a predominant mode of deformation at room temperature, grain boundary sliding and concurrent recrystallization become more predominant at high a temperatures.4&apos;7 Although recovery occurs,8,9 no grain growth has been reported in a Pu even at temperatures near the a =ß equilibrium temperature (-115oC), which is 0.7 of the calculated melting temperature of a Pu.10 From studies on other materials, it appears that high elongations can be obtained in alloys when the THE purpose of this technical note is to present briefly some data revealing high ductility of a Pu, which is normally considered brittle. The very low ductility of a Pu in tension has been reported by many investigators.&apos;-3 Gardner,1 for example, reported that the total elongation of a Pu at a testing speed of 0.015 ipm is less than 0.1 pct at room temperature and only about 1 pct at 100°C. The only tensile creep studies that have been reported&apos; indicate no large ductility, but they were performed on relatively low purity

Jan 1, 1970

By L. S. Reid, R. L. Hunntington

The study of the flow of oil and gas mixtures through oil-bearing formations has received special attention from the petroleum industry within the past few years, and has resulted in a series of research projects based upon various phases of the flow of heterogeneous fluids through porous media. Obviously, the low cost of producing oil during the flowing life of a well makes it desirable to obtain production by natural flow as long as possible and to effect a maximum recovery of oil and gas by the utilization of reservoir energy through efficient methods based upon a thorough knowledge of reservoir characteristics. Despite the extensive research that has been carried out, there is little information available on the behavior of oil and gas mixtures flowing through reservoir formations. This makes it impossible to predetermine the optimum operating conditions for flowing wells. A differential pressure must exist in the reservoir in order to induce flow toward the well. It is a well established fact that with homogeneous fluids the relation of pressure drop to linear distance traveled is a straight-line function as long as the flow is viscous. However, in regard to gas-saturated oils, a number of investigators1l,2,3 have reported that the flow characteristics are materially altered as some of the lighter hydrocarbons are liberated from the oil to form gas while the fluid passes through the reservoir. Most of the work done has been concerned primarily with steady-state flow of liquid-gas mixtures. Cloud1 has studied the effects of saturating crude petroleum oils with various gases, together with the resultant pressure gradients under steady flow conditions, noting that unsaturated oils flowed faster and yet maintained lower pressure gradients than saturated oils. The work of Wyckoff and Botset4 has constituted a major step in the interpretation of heterogeneous fluid flow; especially their concept of

Jan 1, 1938

By A. H. Hand

When considering the question of future demand for crude petroleum in California, one must first decide whether it is to be approached in the light of the definition of "demand" when used in economics; i.e., "The quantity of any commodity required or sought in the market," or in the light of markets developed to dispose of total supply. Therefore, is the California demand of future years to be predicated on a continuation of supplying markets developed following the surplus production commencing in 1922, or predicated on supplying what would be termed economic markets ? If the latter, what are economic markets ? Obviously, the Pacific Coast States and Canada, Alaska, Hawaii and probably the Pacific side of Central and South America, can be considered as normal markets for California petroleum products. While there have been small quantities of gasoline shipped into the PacSc Coast from East Texas, transportation costs, plus import taxes in the case of foreign oil, are a sufficient barrier to justify considering that these markets will be retained. But how about our participation in Atlantic and Pacific foreign and intercoastal markets? During the five years preceding 1931 California shipped substantial quantities of gasoline to the United Kingdom and to France, Germany and Italy. During recent years our business in European markets has been restricted to occasional shipments of gasoline and Kettleman crude. This loss of business is occasioned by the development of production in the Mid-Continent, principally East Texas, and in Iraq, Rumania, Venezuela and other closer producing areas, which makes it impossible at the prevailing crude-oil prices for California to be competitive in supplying any substantial portion of these markets. It is therefore apparent that under a stabilized price structure that will return the California producer a reasonable price for his oil, future Atlantic foreign -business will be restricted to occasional spot cargo sales. As to Pacific foreign shipments which, in addition to Central and South America, consist principally of shipments to Japan, China, Australia and New Zealand: A considerable portion of the business we had with Australia and New Zealand until four or five years ago is now being

Jan 1, 1937

By R. L. Wiegel

This article proposes a physical model for an idealized binary mineral system and for the process of liberation by size reduction. Based on this model, equations are derived relating the amount of each component liberated as a function of the ratio of the volumetric abundance of the two mineral components and the ratio of the mineral grain size to particle size. A definite relationship is shown to exist between the mineral concentration within a locked particle and the frequency of occurrence of such a particle. These relationships are used to obtain theoretical expressions for the concentration-recovery diagram. Physical mineral beneficiation processes are based on breaking a mineral aggregate to liberate the dissimilar mineral grains and then making use of their physical properties to separate the mixture into its components. The effectiveness of the process is therefore dependent on how well the minerals are liberated and how efficiently they are separated. Although a substantial amount of work is being done to improve our understanding of mineral separation processes, the study of mineral liberation itself has been almost completely neglected. The purpose of this theoretical study is to shed some light on the liberation phenomenon by: 1) proposing a physical model for an ideal binary mineral system, 2) treating mathematically the fracture of this system into liberated and locked particles, and 3) deriving an expression for the liberation characteristics of this system. The results of this study are useful in understanding the effect and importance of various parameters in liberation, and provide a basis for comparison with real mineral systems. &apos;RANDOM&apos; MODEL It is recognized that liberation can be caused by detachment which results from fractures occurring at the mineral grain boundaries, or by size reduction which restricts the occurrence of dissimilar mineral locking to a portion of the resulting particles. The detachment effect is dependent on the relative strengths of the mineral grains and the bonds between them, and must be treated empirically for each mineral system. The size reduction effect, however, can be treated analytically if certain assumptions are made concerning the shape and geometrical arrangement of the mineral grains.

Jan 1, 1968

By A. J. Lanza

The prevention of illness among the employees of the mining industry is especially important in view of the importance of the industry, the unsettled conditions of labor, which emphasize the economic necessity for conservation of labor, and for humanitarian reasons. The burden of chronic illness is altogether unwarranted and unnecessary. If the industry is to maintain its labor supply in an efficient manner and keep the standard high, it is essential that it make every effort to keep its labor in good physical condition. The basic principles underlying health conservation are the same for any industry, but they are here applied especially to the mining industry, and more particularly, perhaps, to metal mining, as it is with this phase of the industry that the writer is most familiar, and as it is conceded that metal mining presents more health hazards than coal mining. The first step in the prevention of illness lies in securing employees who are in sound health and free from organic disease. I do not mean that all men who go underground should be physically perfect, but they should be free from organic defects of the heart, lungs, and other organs, or from anatomical defects that would markedly increase their liability to accident. The number of men working underground in mines in this country whose physical condition totally unfits them for such work presents a situation that should not be allowed to continue, and which I believe is not equalled in any other industry in the country. There is but one way to secure men who come up to the required standard, and that is by a thorough physical examination before employment. I am fully aware of the objections felt toward such a procedure by many employers and employees. There is much to be said on both sides, but to any one who is at all familiar with the mining industry as it is today in this country, and who approaches the matter with an unbiased mind, there can be absolutely no doubt as to the necessity for physical examination. As a purely logical proposition this is self-evident, but there remains the further necessity of placing physical examinations on such a basis that they can be administered in a just and equitable manner free from the abuses and suspicions to which they have been subject in the past.

Jan 1, 1919

By J. F. Myers, S. E. Sharp

THE safety data presented in this paper are based upon replies to a Questionnaire sent out to representative mining companies. The authors feel that it is a fair cross section of the milling industry, in that the 17 companies, of the United States and Canada, reporting on 22 mills, are scattered from the Hudson Bay to the Mexican border and from coast to coast. These data concern the accident records of the. various plants from 1939 to 1944, inclusive and the six years are divided into two periods. The first period (1939, 1940 and 1941) represents something of a normal operating condition. The second period (1942, 1943 and 1944) represents the period of time that was most affected by war con¬ditions. During the second period there was a high labor turnover, inexperienced workers were numerous, women replaced men in many kinds of work, a labor shortage existed more or less throughout the industry, and supervision was pushed for peak production. All of the companies reporting compiled their accident experiences for these six years in accordance with the standards set up by the American Standards Association (Engineering Societies Building, New York, N. Y.), consequently the tabulated data presented herein are comparable. The authors of this paper feel that the industry as a whole is greatly indebted to the personnel of the companies that furnished these data, which make this study possible for presentation. This survey covers a total exposure of 74,528,880 man-hours, with 105,471 man-days of lost time from 870 accidents. SAFETY RECORDS In Table I, the safety record is shown of the various mills reporting. The severity rate is usually conceded to be the most vital statistical figure in safety parlance, therefore the participating companies are listed in order of their severity rate for the combined six-year period, under size of organization. The table also shows the frequency rate as well as the frequency-severity ratio (F/S). As noted in Table 1, most of the companies suffered an increase in both severity and frequency rates during the second period; only six of the 22 enjoyed an improvement. From correspondence with the various plants, it seems that a few had very little labor shortage or turnover, and these were not greatly affected. A few plants, anticipating the situation, strengthened their training facilities and actually were able to show a better experience during the second period. This gives great credence to the value of organized training in any safety program. The frequency-severity ratio (F/S) shown in the last column of Table I offers

Jan 1, 1946

By George A. Johnson, Leon H. Banks

The Missouri-Kansas Zinc Corpn., operating in the Waco district, 15 miles northwest of .Joplin, Mo., owns large tailing piles made during milling operations of the years 1918-28 by the Butte-Kansas, Acme, and Barnsdall mining companies, whose holdings have been purchased and consolidated under the ownership of the Missouri-Kansas Zinc Corpn. These tailings had been considered too low in value to be worth retreating by the ordinary methods. C. Erb Wuensch, consulting engineer of the Missouri-Kansas Zinc Corpn., noted the difference in the type of tailing from upper-level and lower-level ore. The latter contained hard lime chats. He also found that mill losses had been due to particles of blende on the corners or sides of the chats and to the existence of soft, porous, cellular, lime chats containing varying amounts of blende. He conceived the idea that a quick grind in rolls or hall rnills might change the type of the rnaterial so that jigging could rnake a clean tailing for discard and a partly concentrated product sufficient in blende content to justify the expense of fine grinding in hall mills to free the mineral entirely. A laboratory was equipped with the necessary machines and the writers were assigned the problem of developing a method of retreating the tailings. Laboratory Testing From preliminary drill sampling of each pile was obtained the blende content, the soluble sulfate content, and the general characteristics of the material to he treated. The tailings were a mixture of lime and flint with some shale. Visual examination showed most of the blende to be in the dolomite and very little in the flint, although there were some flint particles with blende on the cleavages. The blende was found as particles on the corners or cleavage faces in one type of chat and in another disseminated in a soft, porous, cellular lime. Because of the porosity of the latter type of chat, the apparent specific gravity, under hindered-settling conditions, is less than that of a solid piece of lime or flint. That it,

Jan 1, 1930

By Oliver C. Ralston, James E. Norman

Separation of minerals by froth flotation is rightly called an art. It can truthfully be said that no two ores separate in the same way. The difference in results obtained when natural and synthetic mixtures of minerals are separated is so great that such tests frequently have been worthless in attempting to select conditions in which a natural mixture will separate. With a few rare exceptions, the natural mixture is much more difficult to treat than a synthetic mixture, and a much poorer separation is obtained. Perhaps several experimenters have wondered why 10 or 20 per cent of a mineral being floated from an ore does not float and is different from the 90 or 80 per cent that is recovered. In experimental tests on pure sphalerite, observers&apos; have noted that varying amounts of sphalerite may be froth-floated with pine oil alone, the amount recovered in the froth depending apparently upon the source of the sulphide. The only explanation of results such as these, barring insufficiency of frother or time of flotation, is that the surface of the mineral floated is different from that of the mineral depressed. This difference often has been found to be caused by natural contamination of mineral surfaces, apparently brought about by weathering and exposure to natural solutions. There is virtually no rock that is absolutely unweathered. One of the writers had an exceedingly instructive experience in 1931 while working with United Verde copper-zinc iron sulphide ore in Arizona. Nonselective flotation of chalcopyrite and sphalerite away from some of the pyrite was all that could be accomplished. All known depressants produced only slight effect. Sodium cyanide showed some effect, but so much had to be used that only a small amount of chalcopyrite could be

Jan 1, 1939

By W. N. Best

This paper is not intended as a scientific discussion of the combustion of oil but is written from the standpoint of an operator who has the experience and qualifications necessary to guide others in producing the most economical results in the use of liquid fuels. Oil, in this paper, usually means petroleum or its products but incidental reference is made to other liquid and gaseous fuels, so that the term may be considered as referring to all liquid and gaseous hydrocarbons in comparison with solid fuels, as coal and wood. However, only a few of the principal factors in the use of oil as a fuel can be given. The present, and prospective, high price of coal is causing users of fuel to renew inquiry as to the merits of other forms of fuel for industrial purposes. Crude oil (petroleum) is proving to be one of the world&apos;s most valuable mineral resources. The recent discovery that oil underlies a considerable area of the United States, Mexico, and other parts of the world to a greater extent than was formerly believed and the large production of some of the wells in these areas shows the probable quantity of fuel oil that may now be available. Through the energy of Lord Cowdrey, who was one of the pioneers of the oil industry in Mexico, oil has been discovered in England; some prominent geologists believe that it may be found in quantity in Great Britain. For years, oil has been known to be of great value in the manufneture of metals. It has proved incomparable in forge shops, steel foundries, heat-treating furnaces, and wherever accuracy of temperatures is essential, or where a maximum output is desired as well as quality of metal. In some types of equipment, the output produced with oil as fuel is double that obtained with coal and at a reduction of 50 per cent. in the cost of the fuel. For example, in drop-forging plants, the metal is always waiting for the man when oil is used as fuel, whereas with coal, the man must wait for the metal to become sufficiently heated. It has only been since January, 1919, that the oil supply could be relied on for boiler service, owing to the war conditions and the inability to get oil tankers for the delivery of the oil from Mexico to Atlantic ports; but now a constant supply is assured, and many manufacturers are installing it in their power plants. The cost varies with the size of the

Jan 1, 1921

By M. C. Fuerstenau, A. M. Gaudin

Understanding the sedimentation of relatively thick suspensions depends on a knowledge of the concentration of the solids at various positions in the pulp and the times required for thickening. Flocculated kaolin slurries were studied with the transviewer, a device utilizing X-ray absorption in conjunction with a scanning mechanism. A mathematical model based on the Schuhmann size distribution in conjunction with Poiseuille&apos;s law yields experimental filtration rates as a hction of pulp density. These calculations show accord with the experimental results. Accurate predictions of sedimentation results depend upon determining the number and size of pores for given conditions, since the voidage of the suspension controls the volume of liquor that can pass through an element of suspension per unit time. A study on the sedimentation of flocculated kaolin slurries has indicated that their sedimentation takes place by two different processes, dependent on the initial concentration of solids in suspension. One process occurs in dilute suspensions (less than about 2 pct solids by volume) in which a multitude of relatively small flocs settle by hindered settling. In this case, maximal settling velocity is independent of container geometry.1 r2 The other process occurs in relatively concentrated suspensions (greater than about 2 pct solids by volume) in which the mass is considered to be settling as an aggregate network or as one large floc, defined as to size by the dimensions of the container. In this case, container geometry affects sedimentation results significantly. Furthermore, it seems that this single floc is in a state of compression from the beginning of settling, and that two phases of compression settling exist during sedimentation. The first occurs during the early stage of settling where liquid exudes easily and rapidly from the floc, while the second occurs in the compacting portion of the floc where water escapes more slowly and with much more difficulty. Sedimentation of relatively thick suspensions may then be thought to be a filtration phenomenon in which a pulp thickens by the filtration of its contained liquor through the aggregate network of pulp above it. This postulate has also been advanced by others.,4 To understand the sedimentation of relatively thick suspensions more fully, it was felt that knowledge of the concentration of solids at all positions in the

Jan 1, 1962

By Henry A. Ley

Oklahoma produced about 40,000,000 bbl. less crude oil in 1930 than it did in 1929, but developed the largest initial production from current well completions ever recorded in its history. The output of this year would have exceeded all previous years had it not been for state-wide production curtailment. The record initial production of 5,911,982 bbl. from new oil wells completed during the year is accounted for entirely by the rapid development of the Oklahoma City field. Completions declined to the lowest levels since 1909, as a result of a marked reduction in number of dry holes incident to reduced wildcat exploration. Leasing was most active in western and northern counties of the state west of Oklahoma City, but on a much smaller scale than in the preceding year. Geological and geophysical surveys were likewise most active in this western territory. The urge to deeper objectives resulted in the discovery of oil on the Cement fold. Changing economic conditions have created a distress situation among the marginal operators in northeastern localities of the state. Elsewhere in the state production records and successful exploitation of new supplies have been eclipsed by a new social concept of the industry in accord with natural economic developments. Many of the producers of crude oil have organized for a voluntary stabilization of the industry by regulating the output of wells. To enforce their measures these operators have sought for and secured the support of the state. Consequently, the current position of the crude-oil producer is not unlike that of the natural-gas producer—withdrawal of supplies in accordance with market needs. And while the industry as a whole is artificially stabilized by these measures individual operators and some of the integrated concerns suffer hardships. Oil Developments and Production The early operations in Oklahoma were confined to northeastern and eastern localities, beginning in 1885. The first commercial oil wells were completed in 1894, near Chelsea in Craig County, from Cherokee sands in the lower portion of the Pennsylvanian section. Scattered

Jan 1, 1931

AS If see it, then, the engineering advances of which yob have studied here at Golden, the continued growth of. industry that you see about you here in Colorado, and the country-wide progress that I have not time to discuss-these illuminating facts should clear away any doubts as to your future. You have little license to ask, "Where is the call for engineering or what the need? Yankee fashion I might ask you by way of reply, "Have all the mines been opened? Have all the power-houses and transmission lines been built? Have the last improvements in. mill and smelter been in-stalled?" We know that the general answer is No, and the rest of the answer, which tells where are those mines and power plants and what are the new methods and processes in mining and metallurgy, must be sup-plied by you engineers of the future. And anyone who has even casually observed what recent years have brought forth in our profes- sion cannot but envy you your job. Our reconnaissance excur-sion into your future should not be much longer extended, but before turning back there are four landmarks that I would like to point out-not lofty peaks but useful tie points that are worthy of your attention as you traverse the territory of your future work. Two of these are in fact low spots or depressed areas which call for engineering activity; these are commonly called "waste" and "average." The other two are of larger significance and are rather extensive regions in the domain you are to enter and occupy. These larger tracts bear the suggestive place names "fact-finding" and "human engineering" and perhaps will prove to be the heights from which the broadest outlook is to be had in this "pilgrim&apos;s progress:" In the first place, waste deserves your attention, al-though I realize that it is possibly the most unpopular word anyone hailing from Washington can publicly utter. Its unpopularity naturally follows from its overuse in the somewhat strong charges made against the industrial and business world some years ago, when the doctrine of conservation was first preached in the land. But waste is a word to be used in an engineering sense as well as for political effect. Properly used, waste is not a word to shy at-rather it is a challenge to the engineer. For example, at present, the loss of 1 kilowatt-hour to every 5 sold is a clarion call to the electrical engineer. Waste is your target to shoot at, the obstacle for you to surmount, the giant for you to slay.

Jan 7, 1928

By Charles Stuart

A PAPER on this subject can cover but a limited range. A thorough visualization of the subject would contemplate a comparative analysis of haulage machines and batteries of various types; the relationship of the storage-battery locomotive to other types of mine haulage should be considered and limiting factors in each case should be carefully developed. This paper will briefly deal with these factors. So far as the writer has been able to determine, the first storage-battery locomotives for mine haulage were manufactured in 1897 or 1898 and were tried out in the Pocahontas coal field, but they were not sufficiently satisfactory to justify their continued use. Battery explosions were frequent and caused serious damage to the wiring, electrical equipment, and the clothing and bodies of the motormen. Sulfuric acid was used as the electrolyte. Experiments were then conducted with locomotives bearing reels of flexible cable through which connection between the motors of the locomotive and the trolley wire was maintained. At first, these reels were turned by hand. Later, the reels were revolved by contact with the wheels of the locomotive, being raised out of contact with the wheels, by a lever, when necessary. About 1902, the plan of operating the reel, by chain and sprocket wheels, from one of the locomotive axles, as is still the practice, was devised. The popular floating motor-driven reel had its inception in the Pocahontas fields prior to 1906. The maximum radius of operation of the reel-type locomotive is about 500 ft. (150 m.) from point of connection with trolley wire. This is ample for room work and certain entry work, but the need for a machine that would operate entirely independently of the trolley wire was so great that, with the development of the storage battery, renewed efforts were made to manufacture a successful storage-battery locomotive. About 1908, the gasoline locomotive was introduced. In spite of many objections to this type of machine for such work, the fact that hun¬dreds of these machines were purchased was proof of the need for a machine operating independently of the trolley.

Jan 1, 1922

By M. Gensamer

IN applied mechanics and in metallurgy the transition from elastic to inelastic action is a matter of considerable interest and importance. Often the first inelastic deformation is apparently quite homogeneous; that is, uniformly distributed throughout the specimen. Sometimes this deformation is heterogeneous; that is, localized; inelastic deformation proceeds to some definite amount in restricted regions before adjacent regions of the specimen are inelastically deformed. In such cases the deformation does not become homogeneous until the whole specimen has been deformed the amount corresponding to that for each localized deformation. If the test is stopped before uniform extension sets in, the heterogeneous character of the deformation is apparent on the surface of the specimen through characteristic markings, which have been called "Lüders"&apos; lines, "Hartmann&apos;s" lines, the "Piobert effect," or simply "flow figures." These markings are the source of considerable trouble in fabricating operations, particularly in the deep drawing of steel sheet. In many cases where the transition is of this nature, the stress developed at the upper limit of the elastic range is greater than the stress during the period of heterogeneous deformation, giving rise to the familiar "drop of the beam" effect in testing. The amount of the yield-point elongation, as well as the value of the stress at the lower yield point (the value to which the stress drops when yielding begins), are functions of the temperature and the testing speed. Lower temperatures and faster rates of testing increase both the yield-point elongation and the yield-point stress. These matters have been ably discussed in a recent paper by Winlock and Leiter1 though, as brought out by the discussion of that paper, the phenomena are but little understood. The purpose of the present paper is to clarify the problem through the application of a simple principle, and to show that, through the application of this principle, a number of phenomena in the plastic deformation of metals become more readily understood. The principle is this: During homogeneous flow, the rate of work-hardening is greater than the rate of change of stress resulting from change

Jan 1, 1938

By R. E. Head

Some mixtures of sulphide and oxide ores from the Tintic district in Utah are of a sufficiently good grade to be shipped to the smelter without beneficiation. In mining this type of ore, however, a material tonnage of ore of a similar composition but of lower grade is obtained. It is a question of economics whether such ore should be shipped with a certainty of a small return or concentrated if that would yield a sufficiently increased return to amortize plant construction and upkeep and yield a higher rate of profit than at present. It may be assumed that the tonnage of this borderline ore is constantly increasing and that eventually it will attain such proportions as to justify plans for milling on a relatively large scale. Under existing conditions, the producer of mixed sulphide and oxide ores is not greatly concerned about the physical characteristics of his ore or of its mineralogical complexities, since his contract with the smelter calls for payment on the basis of chemical analysis. When concentration is contemplated an entirely different picture is presented. Percentages of valuable metal content must then be con-sidered in terms of minerals, for it is in the form of minerals that recoveries are made and losses sustained. In describing the performance of a given flotation mill and reagent combination, it may be stated as a generality that a specific percentage recovery of valuable elements is made. Technically, however, the concentrator is really constructed and the reagents are selected to recover the valuable minerals. These considerations must be given prominence in discussing borderline ores from the Tintic district because of their physical characteristics and mineralogical composition. Because of these peculiarities they may be justly termed complex, since their lead, silver, and copper contents are each represented by two or more minerals of different chemical composition and presenting widely divergent physical properties. This paper sets forth the results of a microscopic study of a type of borderline ore from the Tintic district that is now being treated by direct smelting. A

Jan 1, 1939

By Fred J. Hurst

In 1934, Irvin Lavine (A), University of North Dakota, stated that the low-rank coals (lignite and subbituminous) of this country represent a vast tonnage of fuel of commercial value and predicted that some day they will play an important role in our economic welfare. Lavine also pointed out that one of the major problems with efficient utilization of the low-rank coals is their high moisture content. Following the discovery of uranium-bearing lignite in the Williston basin of North and South Dakota in 1948 by D. G. Wyant and E. P. Beroni, detailed investigations were conducted (primarily during 1950 to 1954) by members of the U. S. Geological Survey to evaluate the geologic factors and economic possibilities of the radioactive lignites as a source of uranium. The information gained in these studies and summarized in several papers indicated that a large potential reserve of uranium is contained in the subbituminous coal and lignite deposits of the Dakotas and Wyoming (2,3,4). Most investigators concluded that an epigenetic emplacement of uranium in the coal by means of circulating groundwater and the more extensive concentrations of uranium in coal are apparently related to the permeability of the rocks enclosing the coal beds. Breger (5) and others have shown that uranium is readily adsorbed by coal and is held irreversibly as a disseminated adsorbed constituent. Briefly, lignite beds containing 0.1 to 10% uranium have been discovered in the Dakotas and Wyoming. The distribution of uranium was found to be erratic and was usually concentrated in thin layers, which were characteristically 10 to 14 in. thick and occasionally 30 to 36 in. thick. Lignite beds more than 3 ft. thick generally contain more uranium at the top of the bed than at the bottom. Special strip mining techniques are required to mine these thin

Jan 1, 1983

By W. N. Carr, J. R. Biard, B. S. Reed

An analysis of the semiconductor injection laser is presented which is based on a phenomenological model using device and material parameters. The intent of the laser threshold analysis is not to predict from theory the actual threshold current density but rather to provide a logical means of interpreting experimental results. The device and material parameters have been selected such that they describe both the threshold conditions and quantum efficiency of the lasev. A technique is proposed whereby the current required to obtain a population inversion is predicted from device 1-V characteristics. Experimental data are presented which support the analysis. THIS investigation is concerned with the characteristics of GaAs lasers fabricated in this laboratory. However, the assumptions used in these calculations should not limit their application to GaAs alone. It is felt that the analysis is sufficiently general to be useful in describing the operation of other semiconductor-laser materials. ANALYSIS heavily doped semiconductors to be considered. The absorption and/or generation of optical radiation may be completely specified in terms of q(E) and the probability functions f,,(E) and f,(E) which define the occupancy of the valence-band and conduction-band levels, respectively. The symbols used in this analysis are listed at the end. Following the approach of all&apos; it can be shown that the effective gain coefficient, g, in the plane of a forward-biased P -N junction is g(E)=-ai@)[1-fv(E)-fc(E)] [1I In particular Eq. [I] holds for the photon energy at which lasing occurs, Ep. Throughout the following discussion Eq. [I] is considered only for the lasing transition E = Ep. For simplicity the functional energy dependence of the various factors is omitted in subsequent equations. Unless otherwise stated the symbols used represent the values at Ep. If the analysis is limited to the P-type side of the laser junction, the function q(l -f,,) is recognized as the band-to-band absorption in the P-type material at thermal equilibrium. Under forward-bias conditions the function f, is determined by the electron quasi Fermi level in P-type material. For sufficiently large forward bias the second term in Eq. [3] will become dominant and net gain will result; i.e., g will become positive. In order to simplify the subsequent analysis several assumptions are in order at this point. a) No conductivity modulation occurs. /„ is independent of f, and therefore go is a constant. b) The P-type material is heavily doped such that the degeneracy of the valence band permits popu-

Jan 1, 1964

By A. A. Smith

The application of indium to bearings was first advocated by C. F. Smsrtl in 1938, for the purpose of inhibiting corrosion of certain bearing alloys. He found that a thin layer of indium plated on the bearing surface and subsequently diffused at elevated temperatures markedly decreased the rate of corrosion in lubricating oils containing organic? acids. Most of his work was done on cadmium-base alloys, although he showed that the treatment was also effective for copper-lead and other; alloys. Since their introduction, indium-treated bearings have found considerable use, particularly in connection with airplane motors.2 Undoubtedly the effectiveness of the indium plate in resisting corrosion depends upon its relative concentration on the bearing surface after the diffusion treatment and after prolonged use at operating temperatures. Some diffusion experiments were made on a number of base metals that had been indium plated, to determine the depth of penetration after heating for reasonably long periods of time. As only the practical aspects were desired, no attempt was made to determine actual diffusion constants. Method Two different series of experiments were carried out to study the diffusion of indium into several base metals. Cast cylinders about one-inch diameter were machined to 0.750-in. diameter, so as to remove all surface imperfections, and final finishing was done with oo sandpaper. The original diameters were very carefully measured with micrometers and then a layer of indium was electrolytically deposited on the cylinders from a sulphate bath.3 In the first series of experiments, about 0.002 in. of indium&apos; was deposited and diffusion, was carried out at 150°C. for a period of 500 hr. in a thermostatically controlled electric oven. After the diffusion period, successive layers were machined from the specimens and analyzed spectro-graphically and chemically—the spectro-graphic examination serving as a guide to determine which layers should be chemically analyzed. Apparently there was some surface oxidation of the indium plate due to the long heat-treatment, which may have had some effect on the diffusion. A1so, the cadmium alloy showed some incipient melting, which probably was caused by the formation of a low-melting eutectic. To eliminate these factors, another series of experiments was carried out by heating in an electrically heated, automatically controlled, oil bath at lower temperature. The preparation of the specimens was the same as before except that a layer of indium 0.0001 in. thick, an amount commonly used commercially on bearings, was deposited on each of the cylinders. Diffusion was carried out at 120°C. for a period of 200

Jan 1, 1944

By W. C. Lilliendahl, H. W. Highriter

The method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF5) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon completion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then prcssed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times tile uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphitc crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of CO² in Ascarite, using air instead of oxygen to reduce the temperaturc and rate of oxidation. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1). Microscopic examination of ductile and brittle metals disclosed the presence in the latter of an intergranular constituent, harder than the matrix and less easily oxidizable, which was absent from the ductile material. Rough estimates of the volume of the hard constituent

Jan 1, 1935

By Rudolf Kudlich

The problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Latcr, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines—by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care. It is necessary, therefore, to place our reliance mainly on mechanical devices to prevent accidents, and to depend as little as possible on laws,

Jan 1, 1923