Search Documents

By I. E. Rosenzweig

GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula p — 2rca-j [1] where 1 C = -------------------------------------- a a 1 a a [2]

Jan 1, 1940

By H. A. Bauman, T. S. Spicer, C. C. Wright

Experimental data are presented showing the influence of size consist and firing rate upon the performance of bituminous coal-fired, single-retort, industrial underfeed stokers. Size segregation, degradation, and distributor data are also included. The conclusion is reached that size consist of the fuel as fired, is a critical factor in its performance on this class of equipment.

Jan 2, 1950

By P. L. De Bruyn

The behavior of collectors at the mineral-solution interfaces is usually explained in terms of an ionic adsorption process. Through the distribution of collector ions between the solid surface and the co-existing solution phase the mineral is believed to acquire a water-repellent surface coating. Quantitative adsorption studies have been made on simple flotation systems only within the last few years. Such investigations were made possible by the adoption of the radiotracer method of analysis. As a consequence of these studies a new parameter has been added to aid the understanding of the flotation process.

Jan 3, 1955

By T. Airaksinen, R. T. Hukki

A new static pneumatic classifier for the primary separation of the feed material for microclassification is discussed. Pilot plant test results and a novel flowsheet for microclassification at the industrial scale are presented.

Jan 1, 1980

By Ta M. Li

The implementation of the Clean Air Act (CAA) Amendments of 1970 has resulted in a clean fuels deficit that has significant adverse environmental, energy and economic implications, according to the Project Independence Report. The CAA Amendments charge the Environmental Protection Agency (EPA) to establish national air quality standards as well as national standards for significant new pollution sources and for all facilities emitting hazardous substance. Section 110 of the CAA provides the framework for states to establish "emission limitations, schedules, and timetables for compliance with such limitations, and such other measures as may be necessary to insure attainment and maintenance" of ambient air quality standards. State implementation plans (SIP) are subject to EPA approval. EPA is authorized to enforce federal and state requirements by order or civil suit, including injunctive relief.

Jan 5, 1975

By J. D. Miller, R. L. Atwood

The structure, properties, and composition of commercial chelating-type copper extractants are examined. Characterization of these extractants was accomplished using organic separation techniques and analytical tools such as NMR and infrared spectroscopy. Results indicate that only the trans isomer of the diphenylhydroxyoxime (LIX 64N) is capable of copper chelation. The effects of structural modification of the extractants on the extraction and stripping reactions are discussed.

Jan 1, 1974

By F. M. Sandoval, R. E. Ries, J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is a practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota: (1) must be covered with about 70 cm of soil material to achieve maximum production; (2) top-soil must be segregated and spread separately from subsoil; (3) potential production depends on the quality of the soil material returned; and (4) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation.

Jan 1, 1980

By Gary B. Williamson, Barton K. Cross

Digital simulation is a modern analysis tool which allows the mine operator to evaluate the result of making a decision without actually changing the organization or buying the equipment. The purpose of this paper is to demonstrate the use of digital simulation in evaluating a decision of whether or not to introduce dispatching in an open pit mine. The analysis shows that appreciable savings can be realized by dispatching. In certain cases, an operator can reduce the number of trucks required to move a specified tonnage. A second analysis evaluates the alternatives of using one large shovel or two smaller units. In this case, the operating cost of the haulage equipment necessary to support the shovels turns out to be the critical factor in this decision.

Jan 1, 1969

By T. J. O’Neil, S. J. Kirk

In 1978, a multidisciplinary team from the University of Arizona, the Mines Project Group, conducted a study to examine reclamation alternatives for a proposed open-pit copper mine. The cost of a waste dumping plan designed by a mining consulting firm was determined as well as the cost of dumping configuration prepared by the Mines Project Group. The latter dumps were designed to be more socially acceptable and aesthetically pleasing, in addition to serving more creative end land uses than the dumps designed by the mining consultant. One dump configuration designed by the interdisciplinary team was the least expensive plan of all the alternatives considered.

Jan 1, 1984

By H. M. Callaway

There are key words common to Government and the minerals industry, the use of which immediately spark interest, argument and confusion. Among these is productivity, a term ranking for widespread misunderstanding with mineral self-sufficiency and mineral conservation. Each interpretation of these words tends to emphasize a single aspect and either minimize or ignore the complex dynamic system of things that influence the Nations mineral productiveness. This paper1, abstracted from a monograph on lead now being prepared for publication by the Bureau of Mines, not only sheds light on the trend of productivity in the lead-zinc mining industry but it presents the basis for forming a common general notion of what the term productivity implies.

Jan 11, 1961

By Ray W. Amstutz

The shaft was drilled on US government land m the Piceance Creek basin and was funded by the US Bureau of Mines (USBM). It was drilled to 723 m to provide access to rich deposits of oil shale, nahcolite, and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual-string, reverse-air, jet-assist circulation methods were used. Drilling required eight months. Site preparation, running, and cementing the casing required another four months. A 2.44-m ID steel welded casing, 508 mm thick was installed and 2.7 kt of cement were slurried and pumped into the annulus.

Jan 1, 1982

By J. F. Pashak, T. E. Leontis

The effects of zirconium on the properties of sand cast Mg-rare earth metal alloys were discussed in detail in an earlier publication.' It was shown that a significant improvement in strength properties at temperatures up to 400°F resulted from the zirconium addition. In general, the properties of cast Mg-Didymium-Zr alloys were superior to the corresponding alloys containing Mischmetal and the optimum rare-earth level was approAmately 3 pet. Jessup, Emley, and Fisher have also shown the advantages of didymium in Mg-rare earth-Zr alloys, 2

Jan 1, 1961

By P. E. Landolt

MILITARY necessities and economic scarcities, occasioned by the first and second World Wars, led to the search for substitute materials and new products to meet the demands of advancing technology accelerated by research development. Among others, lithium came to attention. Its chemistry had been studied for a long period, but its general use was quite restricted due to limited known sources of raw material. In World War I, Germany used lithium metallurgically for two principal purposes: 1-hardened lead alloy, B-Metal, for railway bearings as a substitute for lead-tin-antimony alloys; and 2-light strong aluminum alloys, Scleron, in which zinc was largely substituted for copper.

Jan 12, 1951

By Zden[e]k P. Bažant

Due to their heterogeneity, most rocks fracture with a zone of distributed cracking ahead of the fracture front. This makes linear elastic fracture mechanics inapplicable. The present study describes a mathematical model in which the progressive microcracking is taken into account by strain-softening stress-strain relation. In a simpler version of the model, the triaxial strain-softening stress- strain relation is obtained by direct adjustment of the elements of the compliance matrix. This formulation is rigorous only if the principal stress directions do not rotate during fracture formation within the fracture process zone. As a more sophisticated and generally applicable model, the so-called microplane model which is an analogue of the slip theory of plasticity is outlined. Comparison with fracture data for various rocks are given.

Jan 1, 1984

By Irvin Mayes, Maher E. Tadros

The effects of particle properties and dispersion on the filtration behavior of magnesiumhydroxide, silica, and polystyrene suspensions in aqueous media were examined. It was found that effective separation of particles can be achieved using filter media with larger pore diameters than the size of the particles. The addition of electrolytes, at concentrations lower than the critical coagulation concentration, to suspensions of polystyrene or silica resulted in an increase of the cake resistance. This result was interpreted in terms of a decrease in the effective particle size due to the increase in ionic strength. For magnesium hydroxide, an increase in the absolute value of the surface charge was associated with an increase in cake resistance and a decrease in cake compressibility. Low cake resistance values were obtained with suspensions of large particles with low surface charge and blocky morphology.

Jan 1, 1980

By J. D. Livingston, Bruce Chalmers, R. L. Fleischer, R. S. Davis

INTERACTION of dislocations on intersecting slip planes has long been considered a primary cause of work hardening in metals. Easy glide and low work-hardening rates have been observed experimentally only when single-crystal specimens were oriented so that one slip plane was initially favored. When single-crystal specimens have been oriented so that initially two or more slip planes were equally favored, high initial work-hardening rates have been observed. In a polycrsstalline aggregate, glide on five systems is in general necessary for a crystal to deform in conformity with the change in the shape imposed by the other crystals.* Only a small fraction of the crystals of a polycrystal will be oriented so that two

Jan 1, 1958

By Courtenay de Kalb

The following observations upon onyx-marbles are fragmentary, and may shortly be rendered superfluous by the appearance of a work upon these interesting stones by Prof. George

Jan 1, 1896

By Luis Toron, Salvador Cortes-Obregon

THE Oaxaca coal fields, shown in Fig. 1, are located in the Alta Mixteca region in the states of Oaxaca, Puebla, and Guerrero. Known outcrops are scattered over 3125 square miles. It is probable that further exploration will reveal a more extensive area of deposits. The region is of great importance to Mexico, as at present the only sources of coal are the fields near the U. S. border. Steel mills are also located in the North, and finished products must travel 600 to 800 miles to the area of consumption in central Mexico. The oaxaca coal, only 120 miles south of Mexico, D.F., lies close to several iron ore deposits. If this

Jan 1, 1955

By I. E. Rosenzweig

GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula p — 2rca-j [1] where 1 C = -------------------------------------- a a 1 a a [2]

Jan 1, 1940

By I. E. Rosenzweig

GEOPHYSICAL prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" II and 12. The current of intensity J, supplied by this battery, passes through the earth between these elec- FIG. 1.-GENERAL ARRANGEMENT OF APPARATUS. trodes. A potential difference U will be measured between two other electrodes V1 and V2, called "potential electrodes." According to the configuration of electrodes (Fig. 1), the resistivity of a homogeneous soil results from the formula p = 2pcaU/J [1] where c=1/a/b11 - a/b12 ? (a/b21-a/b22) [2]

Jan 1, 1938