Search Documents

By D. C. Hilty

It has long been known that in melting high-chromium steels, some of the carbon might be oxidized out of the melt without excessive simultaneous oxidation of chromium, and that higher temperatures favor retention of chromium. The advent of oxygen injection as a tool for rapid decarburization of a steel bath permits significantly higher bath temperatures, and it was quickly recognized that the use of oxygen injection facilitated the oxidation of carbon to low levels in the presence of relatively high residual chromium contents. Up to the present time, however, specific data pertaining to the chro-mium-carbon-temperature relations in chromium steel refining have not been available. Individual steelmakers have evolved practices more or less empirically, but there has been very little real basis for predicting how effective any given practice can be in permitting maximum oxidation of carbon with minimum loss of chromium. The current investigation, therefore, was undertaken in an effort to establish the fundamental carbon-chromium relationship in molten iron under oxidizing conditions. As reported below, the equilibrium constant and the influence of temperature on that constant have been derived for the iron-chromium-carbon-oxygen reaction in the range of chromium steel compositions with what appears to be a fair degree of precision. The practical application of the result will be obvious. Experimental Procedure The laboratory investigation was carried out on chromium steel heats melted in a magnesia crucible in a 100-lb capacity induction furnace at the Union Carbide and Carbon Re- search Laboratories. The charges for the heats consisted of Armco iron, low-carbon chromium metal, and high-carbon chromium metal, the relative proportions of which were calculated so that the various heats would contain from approximately 0.06 pct carbon and 8 pct chromium to 0.40 pct carbon and 30 pct chromium at melt-down. When the charges were melted, the bath temperatures were raised to the desired level, and the heats were then decarburized by successive injections of oxygen at the slag-metal interface through a ½-in. diam silica tube at a pressure of 30 psi. The duration of the oxygen injections was from 30 sec to 2 min. at intervals of approximately 5 to 30 min. It did not appear that length or frequency of the injection periods had any significant effect on the results; cansequently, no effort was made to hold them constant and they were controlled only as was expedient to the general working of the heats. Between successive injections, the heats were sampled by means of a copper suction-tube sampler that yields a sound, rapidly-solidified sample representative of the composition of the molten metal at the temperature of sampling. This sampling device is a modification of the one described by Taylor and Chipman.1 An attempt was made to vary bath temperatures between samples, but it quickly became evident that, unless the variations were small or unless the new temperature was maintained for a minimum of 15 min. during which an injection of oxygen was made in order to accelerate the reactions, a very wide departure from equilibrium resulted. For most of the runs, therefore, temperature was maintained relatively constant at approximately 1750 or 1820°C. A few reliable observations at other temperatures, however, were obtained. Temperature Measurement The high temperatures involved in this investigation were measured by the radiation method, utilizing a Ray-O-Tube focused on the closed end of a refractory tube immersed in the metal bath. The immersion tubes employed were high-purity alumina tubes specially prepared by the Tona-wanda Laboratory of The Linde Air Products Co. These tubes were quite sturdy under reasonable mechanical stress at high temperature. They were unusually resistant to thermal shock, and chemical attack on them by the melts was slow. With care, it was found possible to keep these tubes continuously immersed in a heat for as long as 5 hr at temperatures up to 1850°C, before failure by fluxing occurred. The Ray-O-Tube—alumina tube assemblage was similar to those supplied commercially for lower temperature applications. In operation, the alumina tube was slowly immersed in the molten metal to a depth of approximately 5 in., and the device was then clamped solidly to a supporting jig where it remained for the duration of the run. A photograph of the equipment, in operation with Ray-O-Tube in place and oxygen injection in progress, is shown in Fig 1. When in position in a heat, the instrument was calibrated by means of an immersion thermocouple and an optical pyrometer. For calibration through the range of temperatures from 1500 to 1650°C, a platinum -platinum + 10 pct rhodium thermocouple in a silica tube was immersed alongside the alumina tube. Output of the Ray-O-Tube in millivolts and the

Jan 1, 1950

By Blake M. Caldwell, Harrold D. Owen

The continued use of permanent-type, we11 completion Iras pointed LIP the need for more powerful through-tubing perforating equipment. A new expendable shaped charge perforator has been developed in which the charges are run through the tubing in a vertical position and then opened out to a horizontal position when at the desired shooting zone. The performance of this new tool is comparable to that of conventional casing type perforators. This paper describes the new tool and its applications. Performance data in targets rind under various actual well conditions are presented. INTRODUCTION The general acceptance and increasing use of pernianent-type well completion by the oil industry has indicated the need for through-tubing perforating equipment with performance comparable to that of conventional casing type perforators.'.' To achieve the performance desired, a new, expendable, shaped charge perforator has been developed with adequate power for effectively perforating both 51/2-in. and 7-in. casing below tubing. This has been accomplished without resulting severe damage to the casing and can he obtained under extremes of pressure and temperature. The design of this new tool is a radical departure from previous concepts of tubing guns since it was felt that the two major limitations imposed by previous designs severely handicapped performance. The first of these limitations was the restriction imposed upon the length of the charges by the necessary small inside diameter of the carrier. This resulted from the necessity for compromises in designing a hermetically sealed gun small enough to allow free passage through 2-in. tubing, yet with sufficient wall thickness to withstand some minimum pressure. In an effort to overcome this limitation, the charges were in some cases placed at an angle with the axis of the well with resulting loss in effective depth of penetration. The second limitation concerned the extreme distance of the charges from the casing when the gun was fired. An example of the latter situation is demonstrated by the fact that a conventional 13/4-in. tubing gun centralized in 51/2-in., 17-lb casing has a clearance of more than 1-9/16-in. on all sides. This means that a considerable portion of the force from each charge must be expended in penetrating this 1-9/16-in. of well fluid before it even reaches the casing. With the gun centered in 7-in., 23-lb casing, the amount of fluid penetration required of each jet is in excess of 21/4-in. In a situation where the 13/4-in. gun is touching one side of the 51/2-in., 17-lb casing, the jets from the charges on the opposite side have more than 3%-in. of fluid to penetrate. A similar situation in 7-in., 23-lb casing necessitates the penetration of more than 4-9/16-in. of fluid. The penetrating effect of the charges is severely impaired in passing through so much fluid. Under such conditions, there is usually insufficient force left to penetrate the casing. Previous studies have shown the decided disadvantage of having to shoot through such an excessive quantity of well fluid.'.' The problem. then, was how to position large powerful charges close to the casing prior to firing and still manage free passage through 2-in, tubing. The solution appeared to be in some method of folding sealed charge units in an open type, expendable. 13/4-in. carrier for travel through the tubing, and unfolding them upon their arrival at the shooting zone in the casing. It was desired to control the mechanism electrically from the surface through the regular shooting cable, making the release of the charges independent of the physical characteristics of the well, yet with a provision to prevent the gun from firing until the

Jan 1, 1955

By E. R. Buchanan, R. E. Reed-Hill

Cylindrical magnesium single crystals were deformed in torsion. The axis of torsion was the basal pole. Five crystals were deformed to different strains between 0.08 and 1.03 and then sectioned in order to determine their dislocation densities using the transmission electron microscope. The work hardening rate of all specimens was at least an order of magnitude higher than that normally associated with easy glide in a tension test and comparable to that obserzed in stage B of a tension test. The correspondence between stage B in a tension test and the initial stages of a torsion test is believed to result from the fact that in both cases deformation occurs in a structure containing roughly equivalent densities of the dislocations associated with the three basal slip vectors. THERE are three basic ways of changing the shape of a crystal using slip dislocations. The crystal can be sheared along a slip direction in a slip plane; it can be bent about an axis in the slip plane normal to the slip direction; and, if the slip plane contains multiple slip directions, it can be twisted or rotated about the slip plane normal. Of the three processes, generally known as translational, flexural, and rotational slip, only rotational slip has not been extensively investigated. The object of the present research was to obtain basic information about this phase of crystalline plasticity. This paper is concerned with some aspects of the stress-strain curves obtained by twisting magnesium crystals about their basal poles. Magnesium was selected for four reasons. One, its recovery rate at room temperature is relatively low. Two, single crystals may be easily grown. Three, at room temperature the critical resolved shear stress for basal slip is about two orders of magnitude lower than that for nonbasal slip, so that rotational slip might be expected to occur primarily by basal slip. Finally, relationships between flow stress, shear strain, and dislocation density have been determined for tensile deformation of magnesium crystals,' thereby providing a basis of comparison for the torsional results. EXPERIMENTAL PROCEDURES Crystals were grown from 0.5 in. diam extruded sublimed magnesium rod furnished by the Dow Chemical Co. who reported that it contained in weight percent less than 0.0003 Al, 0.01 Ca, 0.01 Cu, 0.0012 Fe, 0.001 Mn, 0.0005 Ni, 0.003 Pb, 0.001 Si, 0.01 Sn, and 0.02 Zn, with the balance magnesium. All crystals were grown in a dried argon atmosphere using Jill-son's2 modified Bridgman technique. Two different methods were used to obtain crystals with the basal plane normal to the specimen axis. These included direct growth from seeds of the proper orientation, and spark machining (trepanning) of 0.5 in. diam cylinders from larger (1.5 in. diam) randomly grown crystals. The crystals thus produced were polished in a 20 pct HC1 water solution and then etched in a 1 pct HC1 water solution to develop etch pits lying in rows parallel to the basal plane trace. The crystals were then revolved about their axes on the stage of a low-powered microscope. Torsion specimens were prepared only from those crystals whose axes were normal to the rows of etch pits. It is estimated that this simple orientation method was accurate to about 51 deg. 1.625 in. long cylinders were next cut from these selected crystals and then acid machined in a 20 pct HC1 water solution into torsion specimens with a 1 in. long by 0.30 in. diam reduced gage section. Following this, they were annealed in air at 400°C and furnace cooled to room temperature. The specimens were given a final polish in a 10 pct HC1 water solution, rinsed in ethanol, dried, and cemented into brass grips with an epoxy resin. In addition to the torsion specimens, several tensile specimens with their basal planes at 45 deg to the stress axis were also prepared with similar dimensions except that the gage sections were increased to 4 in. in length. The torsion specimens were tested in the apparatus

Jan 1, 1970

By F. V. Lene, E. J. Westerman

The recrystallization behaviors of two extruded and cold-drawn experimental sintered aluminum powder alloys, containing 1.75 and 3.0 pct Al2O3 by weight, were compared with that of extruded and cold-drawn commercially pure alumirzum. The kinetics of recrystallization of the alloys are described semiquantitatively. For the alloy containing 1.75 pct A l203 the rates of nucleation and of growth were also semiquantitatively determined. THE most striking property of aluminum alloys strengthened by a dispersion of Al2O3, the so-called SAP alloys, is their stability at elevated temperatures. One of the manifestations of this stability is their resistance to recrystallization after they have been cold worked. Most of the commercial grades of either the Swiss SAP or of Alcoa's Aluminum Powder Metallurgy Products have not been recrys-tallized after cold working, even when they are heated for a long time at a temperature near the aluminum melting point. Lenel, however, observed that the dispersion strengthened aluminum alloys with a larger spacing between the oxide particles than that of most commercial grades would recrys-tallize.1 It appeared to be of interest to further investigate the mode and kinetics of recrystallization of these alloys, and to compare their recrystallization behavior with that of commercially pure aluminum. Because homogeneous deformation of these SAP alloys in tension did not provide sufficient cold work to induce recrystallization, they were cold worked by wire drawing; the nonuniformity of this deformation unavoidably complicated the interpretation of the recrystallization studies. EXPERIMENTAL DETAILS Extrusions—Two types of sintered aluminum powder extrusions were used in this study. One type, designated AT-400, was produced from Reynolds atomized aluminum powder consisting of spherical particles averaging 3µ in diam and containing 1.75 wt pct of Al2O3. This powder was very similar to the R3M powder from which extrusions were previously prepared with an average spacing of 0.9µ between oxide particles.2 The second type, designated MD 2100, was produced from Metals Disintegrating Co. flake powder containing 3.0 wt pct of Al2O3, with an average flake thickness of 0.8µ. The average spacing between oxide platelets in MD 2100 extru- sions was 0.45µ.2 Powder compacts of 3/4-in. diam were extruded at 1000°F into 0.097-in. diam (AT-400) and 0.093-in. diam (MD 2100) wires by methods previously described.3 In order to compare the recrystallization behavior of sintered aluminum powder extrusions with that of wrought commercially pure aluminum 3/4 in. rod stock of 1100 F aluminum was extruded at 1000°F into 0.102-in. diam wire. Wire Drawing—Tungsten carbide dies were used for the AT-400 and 1100 F alloys. They had an included angle of about 15 deg and reduced the wire area approximately 7 pct per pass. Steel dies with an included angle of 11 to 13 deg and an average reduction per pass of 10 pct were used for drawing the MD 2100 alloy, because drawing this alloy through the carbide dies produced overdrawing defects. Heat Treatment—The cold-drawn wires were cut into small samples, and the deformed ends were etched off. The samples were each wrapped tightly in a single layer of aluminum foil, and individually isothermally annealed in a lead bath. Metallography—The modes and kinetics of recrystallization were determined by metallography. Mounted and polished specimens were anodized in a solution of 1.8 pct HBF4;4 examination under polarized light clearly revealed their grain structures. The recrystallized grains were generally much larger than those of the unrecrystallized matrix, and could clearly be distinguished because they alternated between maximum and minimum light reflection when the microscope stage was rotated, while the unrecrystallized matrix had a comparatively homogeneous "salt and pepper" structure. The fractional recrystallized volumes of the dispersion hardened alloy wires were determined by cutting and weighing of recrystallized and total transverse areas on photomicrographs. The recrystallized grains in the 1100 F alloy were too small to be cut out individually; therefore a combination of cutting and lineal analysis was used in this case. RESULTS AND DISCUSSION Modes of Recrystallization—The modes of recrystallization of the three alloys varied widely. In the 1100 F alloy nucleation and growth started in the region midway between the center and the surface;

Jan 1, 1961

By J. N. Breston, R. V. Hughes

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20's before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By J. Chipman, N. J. Grant, B. M. Shields

The vacuum tin-fusion method of analysis for hydrogen, developed by Carney, Chipman, and Grant, has been modified to permit the analysis of the evolved gases for hydrogen by means of a thermal conductivity cell. A properly prepared sample can be analyzed in 10 min with a probable error of ±0.12 ppm. A study of various methods for storage of hydrogen samples shows that samples can be safely held in a dry ice-acetone bath as long as six days. Storage in liquid nitrogen is necessary for samples to be held one week or more. HE vacuum tin-fusion method, as developed by I- Carney, Chipman and Grant,' is the only analytical procedure which has shown promise of being fast enough for use in the control of hydrogen during steelmaking. It was felt that further simplification and faster speed of operation could be effected by the use of thermal conductivity measurements for analysis of the gases evolved in the tin-fusion method. The application of conductivity measurements to the tin-fusion method is possible because: 1—the evolved gas is essentially a mixture of hydrogen, nitrogen and carbon monoxide with a hydrogen content usually over 50 pct, 2—the evolved gas is collected at a relatively low pressure, and 3— the thermal conductivities of CO and N2 are practically identical while that of hydrogen is very much greater. The major part of this research program was devoted to the construction and calibration of a vacuum tin-fusion apparatus which analyzes the evolved gases for hydrogen by means of a thermal conductivity cell. The second phase of the problem was associated with the development of a procedure for storage of samples prior to analysis. With the rapid quenching method for hydrogen sampling,' which seems to be the most practical for steel mill use, it is necessary that the samples be stored safely during the interval between sampling and analysis if the hydrogen content of the molten metal is to be maintained in the supersaturated solid samples. The thermal conductivity bridge has been used for a number of years in the analysis of certain gas mixtures. An elementary discussion of the theory and practice of gas analysis by thermal conductivity measurements is given by Minter.3 A more comprehensive discussion of the theory and of the various measuring circuits is presented by Daynes.' A complete knowledge of the theory and properties of the thermal conductivity of gases and gaseous mixtures can be gained by a study of the standard textbooks on the kinetic theory of gases."' The existing data on the thermal conductivity of single gases are reviewed by Hawkins: that for a number of binary gas mixtures by Daynes' and Lindsay." The thermal conductivity method may be applied to the determination of the composition of a binary mixture if: 1—the thermal conductivity of the mixture varies monotonically with composition, and 2— the two gases have measurably different thermal conductivities. The greater the difference between the two gases, the greater the sensitivity of the method.10 he method is applicable to the analysis of multicomponent mixtures when all of the gases in the mixture except one have nearly the same thermal conductivity. Fortunately, the mixture of hydrogen, nitrogen, and carbon monoxide evolved by the tin-fusion analysis' falls in this latter classification. The thermal conductivities of nitrogen and carbon monoxide are practically equal; and the thermal conductivity of hydrogen is approximately seven times that of the other two. Therefore, the thermal conductivity of a gaseous mixture of hydrogen, nitrogen, and carbon monoxide at known temperature and pressure can be related directly to the percentage of hydrogen in the mixture by suitable calibration. Usually the thermal conductivity of a mixture of gases is measured at atmospheric pressure where the thermal conductivity is independent of pressure over a wide pressure range. At very low pressures (below 1 mm Hg), the thermal conductivity of gases varies with the pressure. This phenomenon has been utilized in the Pirani vacuum gage for the measurement of pressures in the range of 10" to 10-0 mm of mercury.= Very little has been published concerning the variation of thermal conductivity with pressure at intermediate pressures between 1 mm Hg and 1 atm. However, preliminary measurements indicated that the thermal conductivities did vary with pressure over the range of pressures (up to 10 mm Hg) at which gases are delivered from the vacuum pump. Therefore, the calibration of the thermal conductivity cell had to be planned to include the effects of both gas composition and pressure. Such a calibration chart is shown in Fig. 4. Most industrial applications of the thermal conductivity method of gas analysis have used a compensated Wheatstone bridge circuit containing two

Jan 1, 1954

By L. A. Bromley, A. W. Petersen

The van Arkel-deBoer method for producing ductile titanium by thermal decomposition of Til, vapor and deposition on an electrically heated filament is modified by film boiling Til liquid on a heated filament, resulting in similar titanium deposition on the filament and liberation of gaseous iodine. The deposition rate is higher and the energy requirement smaller than in the van Arkel process. Many problems must be solved before the process is commercially feasible. TITANIUM of 99.9 pct purity, called ductile titanium, has been produced by a modification of the van Arkel-deBoer&apos; method. In the van Arkel-deBoer method, an electrically heated wire is suspended from two electrodes, which are placed in a container holding TiI, vapor at a low&apos; vapor pressure (usually <5 mm Hg). The vapor diffuses to the hot wire, usually maintained at 1100" to 1600°C,&apos; and decomposes according to the reaction liberating gaseous atomic iodine and depositing solid crystalline titanium on the wire. Estimations based on the data of Runnalls and Pidgeon,&apos; indicate that the rate-control ling step is the diffusion of atomic iodine away from the wire. There appears to be nearly thermodynamic equilibrium at the wire with TiI, and iodine as the main gaseous species. TiI, is almost certainly an important gaseous species in the cooler regions.&apos; The liberated iodine diffuses to a heated source of crude titanium and reacts to form more TiI, vapor, which again diffuses to the hot wire and completes the cyclic process. The foregoing process may be modified by suspending the hot wire in liquid TiI,, instead of the vapor, and obtaining film boiling. This type of boiling is characterized by the formation of a continuous film of vapor over the wire surface. Since only vapor contacts the wire sul.face, the temperature of this surface may be raised as high as desirable, within the limit of mechanical strength requirements for the wire. By properly adjusting the input voltage. the temperature of the wire may be maintained above U0C"C; and by evacuating the vessel holding the liquid TiI, and maintaining a suitable condenser temperature, the vapor pressure of TiI, may be held low. Thus, the conditions of operation of the van Arkel-deBoer method may be approximated with film boiling; and hence, it is postulated that ductile titanium may be produced by this method. Preparation of Til, There are many methods available for the preparation of TiI,; that used in this research was prepared by the direct reaction of titanium sponge in controlled amounts with liquid iodine. Although no difficulty was encountered with this reaction, it has since been pointed out that this method is sometimes dangerous and should be used with caution. The resulting TiI, was purified by distillation. First Film Boiling Experiments Apparatus: The apparatus shown in Fig. 1 was used for film boiling TiI, on short wire filaments. The current to the filament was supplied through a bank of three 5 kva transformers connected in parallel. The current was controlled by adjusting the voltage over a 0 to 67.5 v range with a 7 kva variable transformer on the low voltage side of the bank of transformers. The current and voltage were measured by Weston meters. The sealed-in-glass tungsten electrodes were hard-soldered to the filament for the film boiling of TiI,. The bottom part of the reactor, containing TiI,, was wrapped with ni-chrome heating wires to maintain the TiI, in the liquid state. An ice or liquid nitrogen trap, for solidifying I, vapor and any TiI, not condensed, was attached to the low pressure side of the air-cooled condenser. A Megavac vacuum pump was used. Procedure: A 0.010 in. diam tungsten filament was hard-soldered to the tungsten electrodes. TiI, was melted (mp 156°C) and poured into the reactor chamber; the top of the reactor chamber, containing the electrodes, was replaced. Freezing of the TiI, was prevented by controlling the current to the ni-chrome wires wrapped around the reactor with a 1 kva variable transformer. The mechanical vacuum pump was started and the system evacuated to about 2 mm Hg TiI, vapor pressure. The current to the filament was turned on and the impressed voltage slowly increased with the variable transformer. A sudden drop in current at nearly constant im-

Jan 1, 1957

By H. C. Brown

SINCE 1934 the steel industry has been utilizing the spectrograph for supplementing wet chemical analysis in the production control of electric and open hearth furnaces. This means of control made great strides during the war years because of the general acceptance of the spectrograph and the increased emphasis that was placed on rapid control methods. However, in the post war era, with the demand still on increased production, it became apparent that a still more rapid and economical means of production control was needed. Since the spectrograph had been used mostly in the analysis of low alloying and residual elements, it also became apparent that equipment was needed to extend the spectrographic technique to the analysis of the high alloying elements in stainless steel. For these reasons, companies manufacturing spectrographic equipment were prompted to start development work on direct reading instruments. In June 1949, the Applied Research Laboratories of Glendale, Calif., announced that a direct method of spectrochemical analysis for stainless type steels had been developed. This paper will describe the use of the Applied Research Laboratories Production Control Quantometer in the quantitative control of stainless, silicon, and plain carbon steels being made at the Butler Pennsylvania Div. of the Armco Steel Corp. The Armco Butler Div. has one 70-ton electric furnace and six 150-ton open hearth furnaces. The electric furnace is employed in the making of all types of stainless steel and the open hearth furnaces are used for the production of silicon, wheel, and plain carbon steels. The ARL quantometer was purchased primarily for the purpose of controlling the steelmaking in the electric furnace, but its use has been extended for the analysis of final tests (ladle tests) on a number of different types of stainless, silicon, and plain carbon steels. Because of this additional work by the quantometer, substantial savings in manpower and time have been realized by the laboratory. In the analysis of a set of preliminary tests from the stainless steel furnace, approximately 40 min in laboratory time are saved due to quantometric analyses. Despite the fact that more specialty grades of stainless steel are being made in the electric furnace, the average tons per hour have been increased since the quantometer was put into operation. Specialty grades require more furnace time than regular commodity grades of stainless steel. The installation of the ARL production control quantometer was completed on March 13, 1952. By May 1, 1952, the instrument was calibrated for nickel, chromium, manganese, silicon, and molybdenum, which are the elements necessary for the production control of the stainless steel furnace. Within the following month, training of personnel on the quantometer was achieved and a study of the accuracy of the instrument showed that the results obtained were sufficiently accurate for control purposes. Therefore, on June 11, 1952, the quantometer was placed on production control for all types of stainless steels. Starting September 11, 1952, the instrument was gradually placed on ladle analysis (final tests) as the analytical curves were refined and additional curves were drawn. The quantometer has been relatively free of breakdowns since placing it on production control. The samples from only one stainless steel heat have had to be analyzed by wet chemistry because of instrument trouble. The previously existing heat-time record was also bettered by 15 min on a commodity grade of 18-8 stainless steel. Scope of Control In general, the quantometer determines all elements necessary for the production control of all types of stainless steel heats and for the ladle analysis of various types of stainless steel heats. It is also used in reporting final results for silicon, manganese, chromium, nickel, molybdenum, tin, copper, and aluminum on all silicon steel grades and manganese, chromium, nickel, molybdenum, tin, and copper on several plain carbon steel grades. Table I shows the elements and the concentration ranges of these elements in the various types of stainless, silicon, and plain carbon steel that are determined on the quantometer. A study of the results obtained on ladle test samples of stainless steel types 410, 430, 430 Ti, 446, 301, 302, 304, 304L, 305, and 17-7 PH will be discussed. Also included in the study are the results obtained on ladle test samples of a number of silicon steels. Apparatus In order to take full advantage of the potentials of the production control quantometer, the unit has been placed in an air-conditioned room with relative humidity control. The temperature is maintained at 73&apos;22°F and the humidity at 45&5 pct. The air conditioning serves as a precaution to minimize the amount of adjustment and calibration needed during operation. It also reduces contaminating fumes and dust and thereby lessens the necessity for maintenance on the equipment. The quantometer is composed of three units: the high precision multisource unit, the 1.5 meter vertical spectrometer, and the console. The source unit supplies excitation conditions varying from spark-like discharges to arc-like discharges. The voltage to the source unit is supplied by a motor-generator

Jan 1, 1955

By R. V. Hughes, J. N. Breston

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20&apos;s before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By F. H. Callaway, W. O. Keller

The various theories as to the well spacing-recovery relationship are reviewed in considerable detail and these theories analyzed in terms of their consistency with modern reservoir engineering concepts. It is concluded that the well spacing problem must be analyzed in terms of recovery efficiency and that a positive answer to the relation between well density and recovery efficiency is not available from direct comparisons of the production histories of wells and fields. The results of an engineering analysis designed to permit approximate calculation of recovery efficiencies as a function of well spacing in a depletion type reservoir from basic reservoir data is presented. Results of this type analysis indicate that the effect of well spacing on recovery efficiency in depletion type reservoirs can be expected to be very small. Limitations of this approach are pointed out, particularly with respect to its application in lenticular reservoirs. Testing techniques are outlined which should indicate whether or not a reservoir is continuous between wells and whether or not satisfactory drainage is being obtained with present spacings. A mass of data of this type indicates continuity to exist in most fields. INTRODUCTION The purpose of this paper is to review critically the engineering aspects of the well spacing problem, both from the standpoint of certain concepts and from the standpoint of reservoir mechanics. The well spacing problem is primarily an economic problem in which the optimum well density for a particular field is that density which will yield the greatest oil recovery consistent with justifiable development costs. The well spacing answer in terms of economic conditions, however, is extremely sensitive to the variation in recovery efficiency with well density. The variation in recovery efficiency with &apos;References given at end of paper. Manuscript received at the office of the Petroleum Branch October 2, 1949. Paper presented at the Petroleum Branch Meeting in San Antonio. Texas, October 5-7. 1949. well density is properly an engineering problem. Different opinions as to the correct answer to this engineering problem is the basis for most of the wide difference in opinion among various members of the industry as to optimum well spacing. This paper will be confined to the engineering problem of the relation between well density and ultimate oil recovery; economic considerations necessary for the evaluation of optimum well density for any particular field will not be discussed. The paper can be logically divided into two parts. The first part deals with a critical examination of the background and logic of the Cutler Rule and of similar studies by other authors and of related well spacing concepts. It is indicated that the variations in recoveries with well density* observed by Cutler and. others can be logically attributed to regional migration. Theoretical justification of the Cutler type relation wherein observed variations in recovery with well density in the same field is attributed to variations in recovery effiiency, in terms of energy relations, is refuted. The second part consists of a review of concepts of reservoir mechanics with regard to the well density-recovery relation. It is indicated that little variation of recovery efficiency with well density can be expected in a depletion type reservoir, unless lenticular conditions prevent communication between wells. The significance of field test data with regard to the existence or non-existence of lenticular conditions is pointed out. THE CUTLER RULE The first published article concerning the engineering aspects of the well spacing problem to receive wide attention was the work of W. W. Cutler&apos; of the U. S. Bureau of Mines, published in 1924. In a study of decline curves from a large *The expression "well density" as utilized herein refers to the number of acres attributed to each well in a uniform well pattern, and is expressed in acres per well. The term "well spacing" Is utilized to denote the average distance between adjacent wells in a uniform well pattern. †Although the Cutler rule is treated critically in this discussion the authors intend no personal criticism of W. W. Cutler or of his hark The currently accepted concepts of reservoir mechanics were no": existent at the time of Cutler&apos;s work, as were even the moat basic tools (such as the bottom hole pressure bomb) for observing reservoir behavior.

Jan 1, 1950

By J. T. Dewan

An experimental setup is described whereby the responses of Neutron logging instruments have been determined opposite formations of different porosities and under various borehole conditions. The results of these tests are presented in several charts which show how the Neutron log is affected by the following factors: hole diameter, casing, cement, salinity and weight of drilling mud, and position of logging tool with respect to the wall of the hole. The responses in the case of empty holes are also shown. A chart is furthermore presented which shows the shapes of the Neutron log, as a function of logging speed and time constant, at the boundaries between two formations with different porosities. These were derived mathematically using as a basis laboratory determination of the shape of the curve under static conditions, i.e. at very low logging speed. Corrections for the readings made opposite thin beds are given by these computations. The correction is found negligible under usual logging conditions for beds thicker than about 4 ft. INTRODUCTION The Neutron log is used in borehole surveys both for the delineation of porous formations and for the quantitative estimation of their porosities.1,2,3,4,5 It is common practice to calibrate the response of the Neutron log in terms of porosity values for each given geological unit by means of empirical comparisons between the deflections of the neutron curve and the porosity values given by the core analysis in a sufficient number of wells. Usually, the plots of the porosity values vs Neutron log deflections show a definite trend. It is therefore possible to trace an average line across the plotted points. This average line constitutes a calibration curve which can be used to evaluate the porosities from the Neutron logs in the other wells drilled in the same region. Futhermore, when the porosity values are plotted on a logarithmic scale and the Neutron log deflections on a linear scale, the calibration curve is practically a straight line. Accordingly the calibration curves are often determined by simply tracing a straight line between two points corresponding to two widely different porosities. Different choices are made for these two points, depending on local conditions. For example, one point will be defined by plotting the deflection of the Neutron curve opposite a formation known to be very tight, for which an average porosity value of 1 or 2 per cent is assumed. The other point may correspond to shale sections, to which a porosity of around 40 per cent is ascribed. The information provided by the eletrical logs — in particular the Laterolog, Limestone log or Micro-Latero-log — is also very often a help in the calibration of the Neutron logs. Empirical approaches such as these make possible the derivation of fairly reliable porosity values from the Neutron logs in many cases, at least in open holes and in essentially clean formations. There are, however, several causes of uncertainty which may sometimes entail appreciable errors. On the one hand, the Neutron log readings are influenced by the borehole conditions: hole diameter, presence or absence of casing and cement, presence or absence of drilling mud, characteristics of the mud, and position of the logging instrument with respect to the wall of the hole. The amplitudes of the curves opposite thin beds are furthermore atfected by the bed thickness,

Jan 1, 1957

By K. H. Hiller

A rotational viscometer has been designed which perrnits the measurement of the rheological properties of drilling muds and other non-Newtonian fluids under conditions equivalent to those in a deep borehole (350F, 10,000 psi). The important mechanical features of this instrument are described, and its design criteria are discussed. The flow equations for the novel configuration of the viscometer are derived and the calibration procedures are described. The data and their interpretation, resulting from measurement of the flow properties and static gel strengths of homoionic montmorillonite suspensiom at high temperatures and pressures, are presented. Data are also presented for the flow behavier of typical drilling fluids at high temperatures and pressures. The pressure losses in the drill pipe and the annulus depend critically upon the flow parameters of the drilling fluid. This work demonstrates the need to measure these parameters under bottom-hole conditions in order to obtain a reliable estimate of the pressure losses in the mud system. INTRODUCTION The rheological properties of drilling fluids are affected by temperature and pressure, but the extent of these effects on the dynamic flow properties is not well known. Measurements of changes of the flow properties of clay-water drilling muds with temperature have been reported by Srini-Vasan and Gatlin.1 The temperatures reported did not exceed 200F, a limitation imposed by the apparatus used by these authors. The rheological properties of clay suspensions were measured at temperatures up to 100C by Gurdzhinian.&apos; Neither the nature of the exchange ions in the clay suspensions nor the degree of purity were defined in his work, nor were the measurements extended to currently used drilling fluids. The lack of systematic measurements of dynamic flow properties at high temperatures and pressures seems the more surprising since during the last decade the importance of the control of the hydraulic properties of drilling fluids has come to be widely recognized. Very good mathematical treatments of the friction losses in drill pipe and annulus have been developed.3 4 These treatments are based on the assumption that drilling fluids behave as Bingham plastic fluids. Quite often this assumption is justified, while in other cases a power law equation pro- duces better fit than the Bingham model does. For convenience in applying viscometer data to pressure-drop calculations, the Bingham plastic flow equation is preferable and, therefore, has been applied to the data reported in this paper, although other equations may fit these data more accurately. In a Bingham plastic fluid the relationship between the shearing stress 7 and the rate of shear D is given by the following equation: where is the plastic viscosity and 4 the yield point. If 4 = 0, the equation for simple Newtonian flow, 7 = pD, is obtained. Two empirical constants are required for the description of laminar flow of a Bingham plastic fluid, and calculations of the flow behavior at high temperatures and pressures cannot be better than is permitted by the accuracy with which these constants are known. For this reason a high-pressure, high-temperature rhe-ometer has been designed to measure the plastic viscosity the yield point +, and the static gel strength S, at pressures up to 10,000 psi and temperatures up to 350F. The important features of its design will be described. The results of measurements on homoionic clay slurries will be discussed insofar as they are relevant to an understanding of the general flow behavior of clay-water drilling fluids. The results of measurements on some typical drilling fluids will be presented also, and their practical implications will be briefly discussed. DESCRIPTION OF EQUIPMENT MECHANICAL FEATURES A viscometer designed to measure the plastic viscosity, yield point and gel strength of non-Newtonian fluids must permit the measurement of the shearing stress t at any given rate of shear D. This is possible only if t and D are approximately uniform throughout the entire sheared sample. A Couette apparatus is the most convenient method of realizing this condition, as has been pointed out by Grodde." The "high-pressure, high-temperature rheometer" described in this paper is basically a rotational Couette viscometer that is immersed in a cell in which pressure and temperature can be controlled over the range of interest. Fig. 1 shows schematically the important features of the pressure cell and associated equipment. The heart of the instrument is the rotating cup. It is shown more clearly in Fie. 2. which revresents the lower one-third of the pressure cell (below the input drive shaft shown in Fig. 1), and it is shown in detail in Fig. 3. For measurements of dynamic flow properties, the rotating cup is driven by a 1/2-hp electric motor, which operates through a Vickers

By H. H. Kaveler, Z. Z. Hunter

Variation of the horizontal permeability (parallel to the bedding plane) in the vertical section of reservoir rocks has long been observed as a characteristic of a normally heterogeneous system which reservoir rock represent. The use of a recently developed water injection profile device offered opportunity to measure with a high degree of reliability the rate of inflow of water into Burbank sandstone in wells previously cored. Water injection profiles were not correlative with core permeability profiles in such wells. Apparently the vertical permeability substantially influences the flow between strata in a formation in a manner as to void the usual conclusions that have been drawn from consideration of the horizontal permeability measurements alone. The results obtained in comparing water injection profiles with horizontal permeability profiles suggest that many of the usual production operations based upon "selective" behavior or treatment of rock exposed in well bores need to he re-valuated and re-examined. INTRODUCTION Petroleum reservoir rock are heterogeneous systems. Heterogeneity exists in respect to lithologic character insofar as such rock are composed of distinguishable solid phases. Heterogeneity also exists in respect to certain properties, such as porosity and permeability, that vary due to variation of the physi-cal structure of the rock. Except in exceptional cases, both the horizontal permeability (measured parallel to the bedding planes) and the vertical permeability (measured perpendirularly to the bedding planes) exhibit significant variation in any common source of supply. The variation in horizontal permeability. as reflected by con. analyses. has drawn the greatest attention of petroleum technologists probably out of the general notion that the mass movement of fluids in a reservoir is predimonantly in the horizontal direction. Furthermore, in the usual case, the rock permeability measured in the horizontal direction is greater than that in the vertical. The variation of horizontal permeability of reservoir rock has been the basis for developing a number of operating practices and procedures intended to improve the petroleum production operation. Many such procedures are referred to as "selective" in the sense that the practice is intended to control the flow to a more. or less. permeable interval within the common source of Supply. It is often said that such practices are "tailored" to the permeability profile. The practices referred to involve, among others, the following: selective perforation of casing; selective shooting, acidizing and plugging: plugging back to intervals of low permeability; and, regulation of flow to prevent coning of water or gas, or irregular encroachment of water or gas. Certain expressed notions involving a concept of "by-passing," or "trappingl" that are held to be particularly harmful in causing the avoidable loss of recoverable petroleum have grown from observed variations in the horizontal permeability. Oftentimes estimates of the reserve of a common source of supply are tempered by conclusions relating variation in horizontal permeability to recover-ability of the oil-in-place. Certain conclusions attributed to the significance of the variation of the horizontal Permeabilitv often extend to the design and operation of pressure-maintenance projects involving both water flooding and gas-injection. Many advocate increasing the number of injection wells, advocate maintaining uniform and equidistant input-output well patterns, or advocate so-called "dispersed" gas-drive techniques rather than gas-cap injection because the permeability profile of cored wells is supposed to indicate that "by-passing" or "trapping" would otherwise exist. It is important, therefore, to have an opportunity to test whether the variation in the horizontal permeability found through core analyses of a typical reservoir rock is sufficient to establish the paths of fluid flow in a reservoir. It is particularly important to have an opportunity to determine whether flow at the sand face of a well conforms to the permeability profile as established by core analyses. In that manner, the merit of certain 50-called "selective" operating procedures and other notions may be evaluated. The purpose of this paper is to compare horizontal permeability profiles of wells in the Bartlesville (Bur-bank) sandstone with water injection profiles, for the purpose of showing that there is no correlation between the horizontal permeability of a core and the water intake characteristics of a typical sandstone. GENERAL CHARACTERISTICS OF BARTLESVILLE (BURBANK) SANDSTONE The Bartlesville sandstones of Northeastern Oklahoma are off-shore bar deposits.&apos; Although other reservoirs had different processes associated with their deposition or with the formation of their porous, permeable structure, the l!artlesville sandstones on which these field Fields were made are, in every respect. typical petroleum reservoir rock. The permeability of the Bartlesville sandstones shows a typical variation in both the horizontal and vertical direction. Furthermore, the permeability profile logs of wells in any pool are not correlative, even as between wells as close as 660 ft and 330 ft apart.&apos;. The same condition exists in such sand-tones as the Jones Sand at Shuler&apos; and is the ordinary and usual characteristic of reservoir rock. THE FIELD DATA The data reported herein are those obtained from coring of nine wells on the center of ten-acre locations for the purpose of providing water-injection wells in the Bartlesville (Burbank)

Jan 1, 1952

By AIME AIME

THE 139th meeting of the Institute will be held Feb. 17-20, in the Engineering Societies Building, New York. The annual business meeting will be held on Feb. 18 at 10 a. m., and no technical sessions will be scheduled at that time, so that all members may participate in the election of officers, hear the presentation of the annual reports of officers and committees and discuss any matter which they may care to bring up at that time. The annual dinner will be held at the Conlmodore Hotel on the evening of Feb. 20, and the usual good time is promised. Arrangements for this and other social features of the meeting are, as usual, in hands of the New York Sec- tion, of which the chairman this year, Ralph M. Roosevelt, has a well-established reputation earned as president of the Zinc Institute, as host.

Jan 1, 1930

By H. G. Warren, E. W. Hough

Correlation of interfacial tension of the methane-n-pentane and methane-n-decane systems was made by Hough and Stegemeier by the use of the Weinaug and Katz equation. The methane-n-heptane and ethylene-n-heptane systems were investigated by the authors. Additional systems taken from the literature were the me thane-propane system by Weinaug. and Katz, the methane-n-butane system by Pennington and Hough, and the n- butane -carbon dioxide system by Brauer and Hough. These systems were analyzed by the Weinaug-Katz equation and the Sugden equation on the IBM 1620 11 computer using a regression analysis program. Parachor and exponent values for each component and system were determined. The experimental work was close to the critical point of the light component in the n-butane-carbon dioxide and ethylene-n-heptane systems, between the critical points of the light and heavy components in the methane-n-pentane, methane-n-heptane and methane-n-decane systems, and close to the critical point of the heavy component in the methane-pmpane and methane-n-butane systems. An empirical formula was developed to find a value of the constant B in the Sugden equation for binary hydrocarbon systems from the parachor values of the two components. Interfacial tension for binary hydrocarbon systems was found to be a direct function of liquid-vapor phase density difference in the same manner as a single-component system. DISCUSSION Interfacial tension may be defined as the measure of the specific free surface energy between two phases having different compositions.1 The interfacial tension (IFT) for a binary system may be predicted for any temperature and pressure if the

Jan 1, 1967

By AIME AIME

AMONG the members of the Institute there are thirty-three who have been members for a half- century or-more Some time ago a professor of psychology made a careful study of a group of unusually brilliant children to determine whether there was any truth in the general belief that a brilliant mind is usually to be found in a physically sub-normal body. He definitely proved the exact opposite and it is now known that children who are above the average in mental capacity are also above the average in physical health and strength.

Jan 1, 1929

By Orson Cutler, Shepard

THE OBJECT of this paper is twofold: (1) To analyze the forces that cause air bubbles to spread on mineral surfaces in the flotation process; and (2) To develop a rational expression that will serve as a criterion of the floatability of minerals, to the end that the efficiencies of various flotation reagents can be accurately compared. Heretofore, the subject of the spreading of air bubbles has been dismissed with the statement that the surfaces of minerals on which bubbles spread are water-repellent. Imperfect understanding of the forces involved has led to the use, hitherto, of various erroneous formulas for the calculation of the comparative effectiveness of flotation reagents.

Jan 1, 1932

By AIME AIME

The Bulletin. As already announced in the January Bulletin, this publication will be issued during the coming year monthly instead of bi-monthly as heretofore. Among other reasons for this change, it is desired to effect thereby the earlier transmission to members of important papers, lists of candidates for membership, and other items of timely information. The New Haven Meeting. As already announced in special circular, the XCVIth meeting of the Institute for the reading and discussion of papers will be held at New Haven, Conn., beginning Feb. 23, 1909. The Secretary of the Local Committee is Prof. J. D. Irving, Box D, Yale Station, New Haven. The program embraces visits to many interesting works in New Haven, Ansonia, Bridgeport, etc. The leading topics for discussion at the sessions will be: The Conservation of Natural Resources; A Sea-Level Canal at Panama; and The Technical Education of Mining Engineers. But papers on other subjects also are announced. A supplementary session of this meeting will be held in New York City, at some time during March, 1909, as a joint session with other national engineering societies, for the further discussion of the subject of The Conservation of Natural Resources. A Pacific Coast Meeting. The XCVIIth meeting will be held on the Pacific Coast, including a visit to the Exposition at Seattle, and various other points en route going or coming, depending upon the route and program finally adopted. More definite information will be announced at the New Haven Meeting, or at the earliest possible date thereafter.

Feb 1, 1909

By ELTCENE A. WHITE

WE are all interested in our ou7n lines of endeavor and consider ourselves the center of the universe. The farmer thinks he is the most important man because he feeds us. The doctor knows he is the real center because he keeps us well. The lawyer says that he is indispensable because he keeps the peace. The banker furnishes us a place to keep our money and tells us how to make proper use of it. The miner sags that without metals there would be no civilization. I think that my branch has sufficient interest and exhilaration. of accomplishment to fully occupy any man&apos;s mind and attention. Mining and metallurgy are as old as the human race. It did not have much, if any, importance in the stone age as there are not found remains of iron and copper, but in the bronze age, which was co-existent with the stone age, it came to the front. Iron and copper were the most important metals. Copper, as bronze, was known in ancient Egypt, I\~:IS important in Rome and other parts of Europe and in Asia; in South America among the Aztecs and farther North were the Mound Builders and the early inhabitants of Lake Superior. At a very early date the Egyptians conquered the Sinai peninsula for the sake of the copper produced there. The history of copper metallurgy can be compared to that of a flower. The seed is sown in darkness and in the Dark Ages the crude metallurgy of copper began. As the shoot comes up from the seed it may be compared to the age of alchemy; the branches of the plant can be compared to the Middle Ages; the flowering shoots to the 17th century, the budding to the 19th and the blossom to our own time from 1870 on.

Jan 1, 1930

By I. R. Kramer, P. D. Gorsuch, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn&apos; summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948