Search Documents

During the past year the Committee on Coal and Coke has been collecting data concerning various phases of the bituminous industry about which considerable misinformation has been circulated even, in some cases, through the coal trade papers. The data here presented have been compiled by various members, from the most authentic sources available and, where possible, cover the period 1913-1924. They will enable comparisons to be made within the industry, and of this and other industries, and will explain some of the differences between conditions existing now and in the prewar period. Capacity and Over-development The capacity of bituminous mines is frequently stated at figures ranging between 800,000,000 to 1,400,000,000 tons per year. Table 1 shows statistics for the industry, mainly from U. S. Geological Survey sources but partly from U. S. Coal Commission reports. Column 3 gives the mine capacity with equipment and labor as of given date, as estimated from the data published by the U. S. Geological Survey. This is calculated for each State by obtaining the total man days worked as reported by the operators (multiplying average men employed by total days worked at each mine) and dividing this figure into the total production, getting the production per man day; this figure times number of men employed times 308 (a theoretical full working year) equals estimated full-time capacity. Two major objections are made to this method—one that the total number of men employed is used, instead of the number actually working, and the other that the number of days used only deducts Sundays and five holidays. The first objection is answered by the fact that the same number of men is used in estimating capacity as is used in actual production, and while this number is always from 12 to 20 per cent. more than are actually working, this condition exists at all times, although it is worse at times of maximum output. Few coal men will agree with the conclusion that the use of 308 days is correct, as it is practically impossible to keep any mine working full time at the same daily rate of production as when it is working part time, and the opinion is

Jan 1, 1927

By B. Ladanyi

The problem of rock behavior under concentrated loadings has been the subject of a number of studies in the past and has been receiving increasing attention by rock mechanics investigators in recent years. Its application covers various fields, but main interest in its solution has arisen in connection with the problems of drilling, bearing capacity, and rock testing. These widely different purposes and fields of interest probably have been one of the reasons why, in spite of the large amount of published experimental data and several theoretical studies, there are still many points which need further clarification. Another reason for this situation undoubtedly is due to the fact that the rock behavior in indentation is complicated by a great number of influencing factors. Experimental evidence shows that, depending on the rock type (mechanical properties, porosity), environment (ambient effective pressure, pore fluid, temperature), and the type of loading (indenter shape, initial embedment, load level, loading rate), the rock response to indentation may vary within very large limits. The widely different rock behavior has made it impossible up to now to treat the problem with a consistent single mathematical theory, but has required instead a series of simplified models covering only certain most important events in the failure sequence. As far as the theory of rock indentation is concerned, this chapter does not add much new information. Its main purpose is, however, to state the indentation problem in a general manner and to indicate which points need to be studied in more detail before its definite solution is attempted. Also, since excellent reviews of the state-of-art of rock indentation in drilling have recently been given,1-4 this will not be repeated here, and only references pertinent to the points of the problem under study will be quoted. The theoretical part of this study attempts to give a quantitative evalu-

Jan 1, 1972

ARTICLE I NAME AND OBJECT SEC. I. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II MEMBERS SEC. 1. The membership of the Institute shall comprise four classes, namely: 1. Members; 2. Honorary Members; 3. Associates; 4. Junior Associates. All members shall be equally entitled to the privileges of membership, excepting that Honorary Members, Junior Associates, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, .and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. Members shall comprise all those persons who on the third Monday of February, 1918, were members of the Institute, and in addition thereto, all those thereafter elected or transferred into the class of Members. A person to be eligible for election or transfer into the class of Members must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. Graduation from the scientific course of a college, approved by the Committee on Membership, shall be considered equivalent to two years' employment, as required in the previous sentence. Employment as a teacher of engineering, mining, geology, metallurgy or chemistry, if in direct charge, may be considered a position of responsibility as specified in the second paragraph. Persons employed in research or any scientific literary work or in teaching in the scientific departments of colleges, approved by the Committee on Membership, who at the same time are engaged in consulting or in the active practice of mining, geology, or metallurgy, shall be entitled to consider the time so spent in active practice as equivalent to an equal length of time of employment in positions of responsibility, provided the work done or the positions held seem to the Committee on Membership to warrant the equivalency. The requirement of three years' employment in positions of responsibility maybe waived by the Committee on Membership in the case of persons who have done notable original work in mining, geology, or metallurgy, or have won distinction by

Jan 1, 1925

By Alfonso Rizo-Patrón, A.M. Gaudin

Previous studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector. The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest. In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector. The results obtained indicate that a I: I ratio of collector ion to activator ion gives optimum results, and that a 2:1 ratio almost fails to achieve activation and flotation. Yet, a 2:I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion. To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful. The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids; they confirm that an adsorbed coating is inescapable. Apparatus and Supplies The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz. The flotation machine was built according to the design of D. W. McGlashan.* It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel sta-tor, as in the Fagergren laboratory machine. The air intake is controlled by a valve, and the cell consists of a beaker. The quartz was obtained from vein quartz stored in large chunks. It was first crushed to 20 mesh, then sized on a 28-mesh screen. The 20 to 28-mesh size alone was retained for use. This size was freed of coarse iron by passage through a Ball-Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used. The barium was used as barium chloride, Baker's analyzed C. P. The oleate was used as sodium oleate. It was prepared from sodium hydroxide, Baker's analyzed C. P., and oleic acid purified by R. R. de Arellano3 in the laboratories at the Massachusetts Institute of Technology. The purification procedure was elaborated from the recent $researches of Brown and Shinowara.2 It consisted in: (I) saponification of olive oil with potassium

Jan 1, 1943

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By Richard P. Schoemaker

INTRODUCTION IN underground mining operations the effects of economic and mechanical factors on costs and profits can readily be appreciated and can perhaps be expressed in exact figures and percentages. Less apparent, but frequently more important, is the influence of physical stress. Stress causes failure of supports, collapse of openings, rockbursts, and other damage which directly affects the costs of maintenance, and also to a certain extent the accident rate. Stress can, however, if properly directed, be an aid to mining operations. The caving methods in metal mining and the long-wall method in coal mining are well-known examples. In large-scale mining operations it is almost impossible to neglect stress-control. A better understanding of the mechanism of rock pressure and the application of its principles to practical mining will inevitably lead to a reduction in operating costs. Many theories have been advanced to give the mining engineer a practical outline for stress-control but, although today most experts agree upon the principles of stress distribution around underground openings, there is still no generally accepted theory that explains all phenomena. The main reasons for this incomplete understanding of the problem are the lack of accurate knowledge of the physical properties of rocks under field conditions, and the great complexity of these conditions due to inhomogeneity of the rock, stratification, tectonic disturbances, and many other unknown factors. The research on the rock pressure problems has, however, yielded some valuable facts which, expressed in practical terms, and adapted to local conditions, may become a valuable aid for mining operations. The purpose of this paper is to give a review of the most important accomplishments of this research with respect to the stress phenomena around small underground openings, such as tunnels and shafts, so as to arrive at an outline of the problem as it stands today. Special emphasis is placed on a new theory by the German mining engineer, Rudolf Fenner, which has never before been published or discussed in English. THE PRESSURE DOME THEORY The formation of a dome-shaped space around underground openings is well known from field observations. When openings are made in rock under stress, the rock in the top of the openings will often fail, and caving will continue until the openings have assumed a dome-shaped form, after which equilibrium apparently is re-established. The oldest theory which attempted to explain the phenomenon is the "beam" theory, which postulates that the hanging wall consists of stratified measures that behave as independent beams with fixed ends and a uniformly distributed load. When failure of the beam occurs, inward shearing at the ends will cause the formation of a dome-shaped space. The pressure dome theory, which more or less evolved from the beam theory, merely

Jan 1, 1947

By J. B. Cheatham

An analysis of indexing is given for an idealized plastic rock. Indexing refers to chipping from a bit tooth to a previously formed crater. A method is indicated for computing the dependence of chip size and shape as well as force on the tooth for various tooth shapes as a function of crater configuration and distance to the previous crater. Pressure on the tooth is found to vary with depth of penetration after a critical depth has been reached. Damp sand model experiments indicate that simple solutions using linear and logarithmic spiral slip-line fields for Coulomb plastic materials give reasonable approximations to the failure patterns. Both idealized roller cone bits and fixed blade or drag bits are considered, and methods are presented for approximating the force on the bit and the chip volume when the rock is subjected to sufficiently high pressure to behave plastically. One of the primary objectives of drilling research investigations is to develop theoretical equations which can be used to predict the behavior of rock under drilling loading conditions. Since rocks usually fail in a brittle manner at atmospheric conditions, much current research is directed to studies of the brittle failure of rock under the action of drilling too1s. 1,2 The results of triaxial test on rocks indicate that both rock strength and ductility increase at high confining pressures.3 Recent results from single bit-tooth indentation experiments on dry rocks indicate that the transition from brittle to ductile failure under a bit tooth can occur at pressures sufficiently low to be of interest in oil well drilling.4 Single bit tooth experiments and analyses are not directly applicable to the drilling process since one of the important facets in drilling is the interaction between a bit-tooth and the previously formed crater. This interaction is referred to as indexing.' The purpose of the present paper is to indicate how plasticity theory can be applied to the analysis of indexing for plastic rock. Drag bit or fixed-blade drilling is considered and a discussion is given of the drilling action of an idealized roller cone bit. Results of simple experimental studies using a damp sand model are given as a method of visualizing the failure patterns in rocks under high confining pressures. These results are compared with plasticity theory using simple solutions based on linear and logarithmic spiral slip-lines. Discontinuous stress fields are proposed for drag bit drilling based upon the soil mechanics analysis of Shields. SINGLE BIT TOOTH RESULTS Single bit tooth indentation experiments using dry rocks under pressures from 0 to 5000 psi have indicated a correlation between the shape of a force-displacement curve and the nature of the rock failure beneath the tool.4 Continuous linear curves are in-

Jan 1, 1965

By Lloyd R. Jackson

In the past 15 years there has been a great deal of interest in the fundamentals of plastic flow and rupture in metals and a number of papers have presented substantial advances toward a fundamental insight into the mechanism of these two processes. This paper is an appraisal of the present position with respect to the following: 1. The relative importance of shear and hydrostatic stresses in controlling the plastic flow of metals. 2. The relative importance of shear and hydrostatic stresses in determining the amount of flow before rupture in metals. 3. The use of generalized strains in determining the effect of plastic flow on the work-hardening of metals. FundamentalS Involved in Plastic Flow In attempting to devise a quantitative description of plastic flow in metals, it has been customary to assume that metals are homogeneous and isotropic. The fact that neither of these assumptions is correct complicates the experimental appraisal of relations developed. Nevertheless, as will be shown, metals are close enough '0 being isotropic and homogeneous so that considerable insight into the mechanism of plastic flow can be obtained. The assumptions of isotropy and homogeneity allow both the elastic and plastic behavior of metals to be described in terms of 12 variables—six being stress variables, and six being strain variables. From this viewpoint, it should be possible to represent the stress-strain relations in the plastic range for metals by a surface in 12 dimensions. One boundary of this surface would be the surface of transition from elastic to plastic behavior; the other would be the surface of rupture. These two surfaces would be joined by the surface of plastic flow. The shape of this composite surface would depend on the test temperature and speed of straining This paper is concerned only with results obtained at constant temperature and constant speed of straining. While such a representation is conceivable, the demonstration of such a surface would present almost insurmountable obstacles. The most fruitful simplification of this concept has been the recognition that the behavior of metals in the plastic region is primarily a result of shear stresses and strains. Based on this viewpoint, it is possible to utilize stress and strain invariants that are independent of hydrostatic components to define an effective stress and strain. In effect, this amounts to reducing the task of representing stresses and strains in 12 dimensions to one of representation in two dimensions. The two invariants (one for stresses and one for strains) that have received most attention are the following: q2 = ½[(Txx= - Tyy)2 + (Tyy - Tzz)2 + (Tzz - Txx)2 + 3(Txy2 + Tyz2 + 7xx2) [1]

Jan 1, 1947

By Adrian C. Dorenfeld

Laboratory data form the basis for the design of flotation circuits. These data, obtained from testing samples of the ore, should show the optimum con- ditions for concentrating the ore and the effects of change in process vari- ables. Among the more important variables commonly met in flotation practice are: Liberation Size-This is the particle size at which substantially all of the valuable minerals are detached from the gangue minerals. Reagent Additions- Experimental data will show the reagents used and their quantity, quality, and point of addition. Pulp Density-This is an important variable in the design of the flotation circuit because it is one of the factors determining the size and number of flotation cells. Flotation Time-The time necessary to make the separation into concentrate and tailing depends on such factors as particle size and reagents used and must be known for determination of the size and number of flotation cells in the plant. Temperature of Pulp-Temperature affects flotation reactions. Water at approximately room temperature is satisfactory for most flotation separations, but some minerals such as fluorspar are best floated in hot water. Type of Circuit-Many types of circuits can be designed, as discussed in detail later. The laboratory tests should provide data for design of the plant circuit best suited to the ore. Water-Knowledge of the quality of the future plant's raw water is important because water quality may drastically affect flotation results. If possible, flotation tests should be made using samples of the water to be used in the plant. Flotation results may vary with seasonal temperatures and with circulation of reclaimed water. Experimentation can show whether it will be necessary to provide for heating, cooling, treating, or reclaiming the water. Uniformity of Ore-The extent of variation of the ore in hardness, grind- ability, mineral content, and floatability should be investigated so that the designer can ascertain methods to overcome problems caused by ore variations. Settling and Filtration Data-To design the plant flotation circuits, settling and filtration rates and ultimate percentage solids of the various products must be determined. Corrosion and Erosion-Corrosion and erosion tests should be made on the flotation pulps, particularly if the pulps are acid or at an elevated temperature, so that suitable materials of construction can then be chosen.

Jan 1, 1962

By J. D. Milburn, H. J. Hill

In quantitative interpretation of electrical logs the presence of clay minerals introduces an additional variable which further complicates an already complex problern. Although recognizing the difficulties introduced as a result of the heterogeneity of natural sediments and despite the present incomplete state of knowledge regarding electrochemical behavior of shales, dissemirzated clay minerals and concentrated electrolytes, it was felt that useful empirical correlations might be obtained from experimental investigation. Six typical sandstone formations, having a wide variety of petrophysical properties, were selected for the study. Approximately 45 samples from each formation were selected to satisfactorily represent the range of pore size distribution within the particular formation, As a matter of general interest, four limestone formations were also included in the investigation. Previously proposed equations relating to resistivity, SP and interrelationship of the two phenomena have, where possible, been tested with data obtained in this investigation. These equations do not satisfactorily describe experimental behavior of samples through all degrees of shaliness or throughout the range of brine solution resistivities normally encountered in logging practice. An empirical equation has been developed which quantitatively relates formation resistivity factor to satirrnting solution resistivity, porosity, and "effective clay content." This relation is indicated to be uniformly applicable to clean or shaly reservoir rocks. It is shown that both the SP and resistivity phenomena of shaly samples are related to the sample cation exchange capacity per unit pore volume. The independent chemical determination of this parameter is thus a means of determining the "effective clay content" of samples. Some implications regarding theory and electric log interpretation of shaly sands are discussed. INTRODUCTION The use of electrical resistivity logs as a means for estimating formation porosity is based upon the original work of Archie1. It was shown by empirical methods that the resistivity of a rock, when 100 per cent saturated with brine solution, could be related to rock porosity through the equation, F = Ro/ RW = f-m.......(1) where F, the formation resistivity factor, is defined as the ratio of the resistivity of the 100 per cent water saturated rock, Ro, to the saturating solution resistivity, Rw; f is the ratio of pore volume to bulk volume; and m is the slope of the average line when the data are plotted on log-log paper. This relation was established for relatively shale-free formations containing water having high salt concentrations, and under these conditions F may be considered constant for a given rock sample. Applications of Eq. 1 to interpretation of logs of shale-free formations has been quite successful when satisfactory formation water resistivity data could be obtained. The most readily available means of estimating formation water resistivity is the self-potential log. Conventional methods of SP log interpretation involve correct.

Jan 1, 1957

By Craig E. Saporito

INTRODUCTION Freeport-McMoRan Inc. has been very active recently with two major discoveries and its restructuring activities. This paper describes Freeport-McMoRan's businesses, the two major mineral discoveries, and exciting opportunities within the oil and gas operations. BUSINESS ACTIVITIES Freeport-McMoRan is the largest and one of the lowest cost fully integrated U.S. phosphate fertilizer producers. It is the second largest domestic Frasch sulphur producer. Freeport- McMoRan will become the largest domestic producer of Frasch sulphur when its Main Pass Block 299 sulphur deposit reaches full production in 1993. Furthermore, it is the largest transporter of sulphur produced by others. Its oil and gas activities rank among the largest U.S. independents in terms of production and proved reserves. The copper/gold operations in Indonesia are among the world's lowest cost. When expansion operations reach full capacity levels in 1992, the Indonesian copper/gold complex will be the fifth largest copper operation in the world. Operations are divided into three business segments that include: 1. Agricultural minerals, incorporating sulphur, phosphate rock and phosphate fertilizer activities; 2. Energy, including oil and gas activities; and 3. Metals, incorporating copper, gold and silver operations in Indonesia. In early 1989, Freeport-McMoRan announced the discovery of two world-class ore bodies; a sulphur deposit off the coast of Louisiana on Main Pass Block 299, and a copper/gold deposit -- the Grasberg in Indonesia -- approximately two miles away from the existing Ertsberg East operations. As a result of these major discoveries, Freeport- McMoRan decided to carry out a restructuring program. Its purpose was to sell $1.2 to $1.5 billion of non-strategic assets. Debt levels and associated interest expenses will be significantly reduced, and general and administrative expenses will be reduced, which will place Freeport- McMoRan in an excellent position to fund the development of the Main Pass Block 299 sulphur discovery, the Grasberg discovery, and oil and gas discoveries. This restructuring program also will allow Freeport-McMoRan to achieve the greatest future value for shareholders by focusing on its principal businesses (Figure 1). Strategic Restructuring • Sell $1.2 - $1.5 Billion Of Non-Strategic Assets • Significantly Reduce Debt • Significantly Reduce G&A • Fund Development Of Main Pass & Grasberg • Stronger Company; Positioned For Future Growth • Focus Is On Principal Businesses: - Sulphur/Phosphate Fertilizers - Indonesian Copper/Gold - Oil And Natural Gas Figure 1 - Strategic Restructuring AGRICULTURAL MINERALS Main Pass Block 299 Discovery The Main Pass Block 299 discovery has a proven reserve of 67 million long tons of recoverable sulphur. This is the largest known Frasch sulphur deposit in North America. The discovery increased Freeport-McMoRan's sulphur reserves more than five-fold, and is synergistic with the company's phosphate fertilizer assets. The

Jan 1, 1990

Discussion of the paper of W. R. Shimer and F. O. Kichline, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 81, September, 1913, pp. 2361 to 2377. ALLERTON S. CUSHMAN,* Washington, D. C.:-I have been much interested in Mr. Shimer's valuable contribution. The apparent fact that the oxides of certain metals which are not reduced by hydrogen per se, are reducible when the oxides are dissolved in iron in small quantity, is brought out for the first time, and is worthy of the careful attention of investigators. The Ledebur method has been subjected to considerable criticism, owing to the alleged fact that it did not measure the oxygen combined with impurities. Personally I have found the method extremely helpful in spite of the minute quantities of oxygen with which it deals. Mr. Shinier points out that the highest oxygen he obtained by over-blowing was 0.074 per cent., while the minimum quantity in a properly finished steel was in the neighborhood of 0.02 per cent. The Ledebur method is used as a constant check on the quality of heats made in practice under my direction. In dealing with a very pure commercial iron, we should expect to find and would find difficulty in galvanizing sheets made from a heat running 0.07 per cent. oxygen. In fact, we do not like to have the oxygen rise above 0.03 per cent. I am inclined to agree with the author that excessive oxygen leaves a bath of metal in a very short time, but nevertheless I believe it takes only a very little combined oxygen to begin to make its presence felt in the pickling and galvanizing department, when sheet metal is the product manufactured. As Mr. Shimer points out, the higher the carbon, the lower the oxygen danger, and it is partly for this reason that the manufacture of carbon-free metal in the open-hearth furnace has to be so very carefully watched and controlled from the furnace through to the finished product. It is quite possible that, there is a critical temperature of dissociation between iron and oxygen, although the critical points may vary in baths of different carbon content. Unfortunately, the accurate determination of the temperature of a molten bath at the time of pouring or teeming is a very difficult matter. For a long time I have been wishing that there were some reliable data which would indicate the effect of the tem-

Jan 12, 1913

By John W. Vanderwilt

THE unpredictable behavior of ground movement and subsidence has complicated the problems that attend the extraction of large quantities of ore. Special studies, particularly relating to coal mining, have yielded such a voluminous literature and so many involved controversial theories that a partial review would be difficult. Limited space makes any kind of a review impractical. The features to be considered cover only a relatively small part of the broad problems of ground movement and subsidence, but it is believed that this small part is critical. The practical aspects are important, since they bear directly on safety of mine workings, on recovery of ore and on dilution of ore in block caving and related systems for extracting large quantities of rock. The ground movement to be described occurs outside the vertical boundaries of a caved block in the area that is commonly referred to as being in the "zone of draw." "Draw" is a term that originated in the subsidence problems related to coal mining, and it is defined by a line drawn from the margin of the area caved underground to the most distant fracture at surface on the same side of the caved area as shown in Fig. I.1 " A line thus drawn is called the cave line, and its angle with respect to the horizontal is the cave angle or angle of draw. It is understood that the line is taken normal to the limit of mining, and in a vertical plane. The prevailing theories as to draw and angle of draw assume that appreciable movement occurred along the cave line, which has been described as a fracture resulting from the shearing action brought about by the weight of the overlying load. Fig. 2 shows diagrammatically the mechanics of ground movement adjacent to an area of subsidence according to the prevailing theory of draw (A, from Royce2) and, for comparison, ground movement observed in the Climax mine (B). The text in Peele's Handbook2 referring to Fig. 2 does not state the meaning of the "original position of top of workable ore" in the rectangular space above "ore in place," and the arrows are not explained. However, this presentation is most concerned with the zones outside the rectangle. According to the prevailing theory, as shown at the extreme left under A, Fig. 2, the vertical tension cracks at surface change at a shallow depth to shear fractures forming the cave line, and it is assumed that appreciable movement takes place along the cave line toward and into the subsiding caved block. The mechanics of ground movement observed in the Climax mine, as shown under B, Fig. 2, does not accord with the prevailing theory, particularly as regards the cave angle and draw. The vertical

Jan 1, 1946

By L. D. Frink

THOSE actively interested in mining are fully aware of the ever-increasing difficulty of making conditions such that efficient work can be clone in underground openings, especially as higher rock temperatures are encountered in depth. This is also true where an effort is being made to cut down the burden of overhead expense by working headings 24 hr. in a day if blasting is done as often as is possible in that time. That the conditions resulting from both these causes have driven the native-born Americans from the mines and that their places have been taken by less efficient foreigners is a fact that we must all admit. The great war now being fought in Europe and the educational qualification clause written into our immigration law by the last Congress will probably limit very materially the supply of labor, such as we are now using in our mines, and will force upon mine operators the necessity of making this work appeal again to Americans. Metal tubing, with blower or exhaust fans, has long been used in supplying air to dead ends where natural ventilation is impossible, or in driving the smoke from such places, or in doing both, as the need might be. Here in Butte we have now come to use canvas tubing very extensively and find that it has many advantages not possessed by the metal. The use of flexible tubing is not new, but it has not been generally used in mining operations. Recent improvements, however, in the canvas itself and in the jointing of sections and manner of suspension have so increased its usefulness that it promises to add much to the efficiency of mining. There is now on the market a product that is impervious to air, is fireproof, and has a system of jointing which, permits it to be put up or taken clown in a few seconds. In this article an effort will be made to explain the manner in which canvas tubing is being used in the North Butte company's operations at Butte, Mont. The accompanying photographs will, I hope, help make clear what may be done with this material.

Jan 1, 1918

By Alfonso Rizo-Patrón, A. M. Gaudin

Previous studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector. The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest. In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector. The results obtained indicate that a I: I ratio of collector ion to activator ion gives optimum results, and that a 2:1 ratio almost fails to achieve activation and flotation. Yet, a 2:I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion. To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful. The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids; they confirm that an adsorbed coating is inescapable. Apparatus and Supplies The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz. The flotation machine was built according to the design of D. W. McGlashan.* It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel sta-tor, as in the Fagergren laboratory machine. The air intake is controlled by a valve, and the cell consists of a beaker. The quartz was obtained from vein quartz stored in large chunks. It was first crushed to 20 mesh, then sized on a 28-mesh screen. The 20 to 28-mesh size alone was retained for use. This size was freed of coarse iron by passage through a Ball-Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used. The barium was used as barium chloride, Baker's analyzed C. P. The oleate was used as sodium oleate. It was prepared from sodium hydroxide, Baker's analyzed C. P., and oleic acid purified by R. R. de Arellano3 in the laboratories at the Massachusetts Institute of Technology. The purification procedure was elaborated from the recent $researches of Brown and Shinowara.2 It consisted in: (I) saponification of olive oil with potassium

Jan 1, 1943

By E. W. Hough, G. L. Stegemeier

Empirical equations for surface tension of propane and normal butane as functions of reduced temperature are obtained from experimental data. Another correlation relating surface tension to enthalpy of vaporization is given for these two compounds. In addition, new paracbor numbers are calculated for the normal paraffin hydrocarbons. These numbers are utilized for the calculation of interfacial tension of two-component systems as functions of pressure and temperature, using a modified form of Weinaug-Katz equation. The experimental data for two binary systems are approximated by the correlation. From these results it is found that the interfacial tension in the high-pressure region remains extremely low at large pressure decrements below the critical pressure. Thus, it appears that condensate systems may have flow characteristics almost like single-phase conditions even though the pressure is within the two-phase region. Experimental data have shown that interfacial tension divided by density difference approaches zero as the critical pressure is approached. A calculation of wetting-phase saturations indicates that the saturation gradient at the two-phase contact becomes increasingly abrupt as the critical pressure is approached. DISCUSSION Prediction of the surface and interfacial tension of the light hydrocarbons and of two-component hydrocarbon mixtures at various temperatures and pressures may be made if other physical properties are known. Extensive experimental work on single-component and binary systemsl is the basis for the correlations outlined in this paper. Interfacial tension is defined as the specific surface-free energy between two phases of unlike fractional composition, while surface tension is defined as the specific surface-free energy between two phase:; of the same fractional composition. The usual definitions relating interfacial tension to a liquid-liquid interface and surface tension to a gas-liquid interface are not clearly defined when the critical region is included, and there is no sharp distinction between a gas and a liquid phase. Interfacial tension is probably the most important single force that makes one-half to one-third of the total oil actually in place in a reservoir rock unrecoverable by conventional gas-drive or waterflood methods. A rough estimate of this figure for the United States is 100 billion bbl. Interfacial tension presently is used by petroleum engineers in the estimation of saturation gradients at the gas-oil contact and at the oil-water contact. The data in this paper should prove useful for estimates of reserves involving gas-oil contacts. Relative permeability undoubtedly is influenced by interfacial tension, for sufficiently small values. These data should be useful in determining how small the values are In addition, these data should eventually add to our fundamental knowledge of surfaces. At the critical point, all surface excesses approach zero and the thickness becomes very large. SINGLE-COMPONENT SYSTEMS It has been observed1 that the following relationships are good approximations to the physical properties of propane and n-butane.

By B. M. Larsen, T. E. Brower

IN two previous papersl,2 dealing with the carbon-oxygen reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity 0[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm,; that is, if [C] X [O] is taken as 0.00222, 0[O] = [O] - 0,00222/[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.' This quantity 0[O] proves to be substantially independent of carbon content over the range 0.08 to 1.2 per cent, as well as of the basicity of the slag, and is nearly always within the limits 0.015 to 0.025 per cent when the bath is boiling normally and is in what we have termed a steady state. Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, 0[O], on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in ?[O] level following addition of Spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. VARIABILITY OF EXCESS OXYGEN IN NORMAL OPEN-HEARTH OPERATION The preceding general statements refer to the average value of ?[O] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining oxygen from the gas phase above it, or from added ore, faster than it is losing oxygen to the metal; yet when the bath starts to boil vigorously, the opposite condition may prevail for some time. The consequence of this lag is a variation of ?[O], the interpretation of which in a single heat may not be immediately obvious, This condition is illustrated in Figs. I and 2. In Fig, I, ?[O] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small ore feed causes only a small rise in 0[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1946

By C. R. Fondersmith, John Chipman

In the manufacture of rimming steel—which constitutes the bulk of the world's production of mild steel—the factors that determine the quality of the product are very closely associated with the pouring and solidification of the steel in the ingot mold. The behavior of the metal in the mold is, on the one hand, the resultant of the complex processes through which the liquid metal has passed, and, on the other, it is an indication of the probable behavior of the ingot during subsequent rolling and finishing operations. A detailed study of the mechanism of solidification of rimming ingots ought to yield information that will be useful in controlling the structure of the ingot and the quality of the ultimate product. The first step in such a study is to determine the rate at which the solid shell of the ingot forms from the liquid metal in the mold. A knowledge of the rate of solidification will make it possible to correlate observations of rimming action and gas evolution with studies of the structure, porosity, and segregation within the ingot. Thus, if the metal in the mold is observed to fall, let us say one minute after pouring, the portion of the structure associated with this fall will be located in the part of the ingot that is solidifying at that particular moment. The knowledge that the ingot solidifies to a depth of 3/4 in. in the first minute enables us to locate in the ingot the structural features corresponding to the observed fall. Conversely, the blowhole condition associated with a rising or growing ingot will be found in the part of the ingot that is solidifying at the time the phenomenon occurs. The time required for the complete solidification of an ingot has long been a matter of speculation. It is of considerable practical importance in connection with charging and heating in the soaking pits. Too rapid handling of the ingot through heating and rolling processes has been thought to be associated with excessive pipe and other internal defects, so that a further object of this investigation was to attempt to estimate the time required for complete solidification, or the minimum practical time within which the subsequent operations can be performed with the minimum hazard.

Jan 1, 1937

By D. R. Packard, J. D. Verhoeven

The resistivity us atom fraction relationships for dilute solutions of cadmium, mercury, and tin in molten sodium have been determined. With these data and the resistivity capillary-reservoir technique, the electro-transport mobilities, effective valences, and the diflusion coefficients of the three solutes have been determined. The mobilities are found to be higher than in other molten alloys by a factor of around 20. The results are compared to the Mmgelsdorf model for electrotrmtsport. The high values found for the mobility to diffusion coefficient ratio indicate that small quantities of the alkali metals should be susceptible to purification from many solutes by means of electrotransport. PASSAGE of a direct electric current through a liquid metal containing a solute will usually cause a relative motion between the solute and solvent atoms of the alloy. This electrotransport phenomenon may be described experimentally in terms of the mobility of the solute atoms, i.e., the drift velocity of the solute relative to the solvent per unit electric field. In dilute solutions of liquid alloys this relative mobility becomes a measure of the velocity of the solute with respect to the observer since the motion of the solvent is negligible. The mobility is a significant parameter in evaluating the potential usefulness of electrotransport for such things as purification or solute control upon solidification. Prior to around 1958, quantitative data for the mobility of solutes in liquid metals were restricted to some solutes in liquid mercury. Since that time ad- ditional data have been reported for the mobility of solutes in liquid mercury, bismuth, tin, and lead, as shown in Table I. In 1963 Drakin et al.11 reported some values of a transport number for mercury and thallium in molten sodium and potassium. When these values were converted to mobilities, it was found that the mobilities were higher than any of the previously reported values by a factor of around 20, as shown in Table I. Drakin's experimental technique did not eliminate the presence of back-diffusion and consequently his data were expected to be lower than the true values. The purpose of the present investigation was to determine the mobility of a number of solutes in molten sodium with an experimental technique which eliminates back-diffusion errors. EXPERIMENTAL The technique used to determine the mobility was a resistivity capillary-reservoir technique which had previously been used with a high degree of precision on Sn-Bi alloys.4 This technique consists of dipping the vertical Pyrex capillary cell shown in Fig. 1 into a molten bath of alloy while the bath and capillary are under vacuum. The capillary is then filled by intro-

Jan 1, 1969

By R. H. Jacoby, V. J. Berry

Future depletion performance and ultimate oil recovery from reservoirs producing under volumetric control are often predicted with the aid of a material balance equation. When the reservoir fluid is very volatile, however, certain assumptions implicit in the use of the conventional methods are no longer valid. This is became laboratory differential vaporization test procedures do not adequately represent the reservoir depletion process and the performance of surface separation facilities. In such cases recovery of stock tank oil per unit of pressure decline can be predicted only from a detailed knowledge of the separator conditions and the over-all composition of the fluid entering the wellbore at each stage of depletion. Surface recovery is not simply related to the total quantity of liquid flowing into the well under reservoir conditions. In order to improve predictions for reservoirs which produce volatile oils, a step wise method of calculation has been developed. This method uses relative permeability data and multicomponent flash calculations to predict oil and gas production as a function of reservoir pressure. Calculations are presented for a reservoir containing a volatile crude oil, and predicted tank oil recovery by primary depletion is more than twice that predicted by conventional methods which are known to be adequate for ordinary black crude oils. Calculated maximum produced gas-oil ratio is less than one-fourth of the conventional prediction. Wellstream compositions have also been used to determine variation in stock tank oil composition and liquid content of the separator gas. This information is of particular importance for crude stabilization calculations and for design of gasoline plant facilities to recover LPG and natural gasoline. INTRODUCTION The estimation of oil reserves and the prediction of future recovery performance of petroleum reservoirs is a frequent task of the petroleum engineer. If the reservoir produces under volumetric control, performance calculations for primary depletion are made by combining oil and gas material balances with the gas-oil flow characteristics of the reservoir rock. For black oil reservoirs, the Schilthuis1 type material balance is commonly employed. For gas or gas-condensate reservoirs, where only one phase is flowing under bottom-hole conditions, a more simplified material balance is used. In the period in which these material balance methods were conceived and put into practice, it was common to classify reservoirs according to the type of fluid produced as (1) black oil reservoirs, or (2) gas or gas-condensate reservoirs. Recently, however, deeper drilling and more extensive studies of reservoir fluid properties have led to the recognition of reservoir fluids with phase characteristics between those of ordinary black oils, and gases or gas-condensate fluids. These intermediate fluids contain relatively large amounts of the hydrocarbons ethane through decane and are found in deep, high temperature (250°F) reservoirs. Such fluids are often referred to as high shrinkage crudes or "volatile oils." They are usually characterized by tank oil gravities above 45° API. high solution gas/oil ratios,

Jan 1, 1958