Search Documents

By E. V. Potter, H. C. Lukens

The volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.² Both sets of data show a minimum solubility between 500' and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. Therefore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. Apparatus and Method The apparatus and method were essentially the same as those described in the previous work,' as shown in Fig. I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transi- . tion points determined under such conditions were less accurate. Absolute Solubility Procedure ad Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1947

By M. G. Benz, J. F. Elliott

A new type of solution calorimeter has been constructed to measure heats of mixing, enthalpy increments, and heats of fusion, formation, and reaction at temperatures above 1000°C. With it, measurements hove been made of the partial molar heats of mixing joy tin in the Cu-Sn system from 0 to 13 at. pet Sn at 1127°C and fir nickel in the Cu-Ni system from 0 to 9 at, pet Ni at 1200°C. The integral molar heat of mixing for the Cu-Sn system is strongly negative with a calculated minimum value corresponding to the composition Cu3Sn. The integrnl molar heat of mixing for the Czi-Ni system is slightly positive at these temperatures. These integral molar values have been measured with a probable error less than 30 cal per g-atom at an atom fraction of nickel or tin equal to 0.1. The estimated probable error for the Cu-Sn system is approximately 450 cal for a measured heat of solution of approximately 9000 cal. For the Cu-Ni system it is approximately 700 cal for a measured heat of' solution of approximately 60 cal. A new type of heat of solution calorimeter was designed and constructed to provide a more accurate experimental method for determining heat effects at high temperatures, (T > 1000°C). With it, partial molar heats of mixing, enthalpy increments, heats of fusion, and heats of formation and reaction for metal systems can be measured directly. Previously it has been necessary to rely upon the use of the dropping calorimeter or the van't Hoff equation applied to equilibrium data for this information. For the most part equilibrium data are scarce and difficult to obtain in many cases, and it has been necessary to rely upon the "method of mixtures" for the desired enthalpy measurements. An earlier study1 provides a prototype for this work. The "method of mixtures" as outlined by K. K. kelley,2 "consists of dropping the substance under investigation from a furnace, with controlled and measured temperature, into a calorimeter operating at or near room temperature.'' In this manner the change in the total heat content (enthalpy) of the substance between the temperature of the furnace and that of the calorimeter is determined. In order to determine high-temperature heats of mixing, enthalpy increments, and heats of fusion, formation, and reaction, it is necessary to take the difference between two such measurements, one before and one after the occurrence of the enthalpy change being studied. The desired enthalpy change is then the small difference between two large numbers. Small errors in the large numbers are included as large errors in this small difference. It is this difficulty that must be avoided for accurate measurement of the desired functions. The procedure with the new solution calorimeter consists of dropping the substance under investigation from a furnace, with controlled and measured temperature, into a solution calorimeter operating in the temperature range of 1000o to 1200°C. Measurements in the range of 1200" to 1600°C are planned for the future. By selection of the composition and

Jan 1, 1964

By B. N. Webber

During World War II the Pocos de Caldas bauxite deposits of Minas Gerais in Brazil yielded some 60,000 tons. Since then they have maintained a small but almost continuous production. Known for many years, the deposits have been reconnoitered by a number of geologists,1-4 but no dimensional study has been possible because there have not been enough exposures to show clearly the depth, bedrock, and habit of occurrence. The deposits are somewhat unorthodox in their occurrence mainly on steep slopes of mountainous terrain. Although the parent rocks are a sequence of alkalic intrusions that bauxitize readily under the proper conditions, bauxitization has not been the dominant weathering process in the area. It is limited to certain localities where important volumes of bauxite have formed by laterization of several rock types, each yielding a distinctive type of bauxite. Bauxitization may be observed in several stages and in both direct and indirect cycles of formation. The deposits are unique in being of demonstrably recent age, so that the conditions under which the bauxite formed are essentially those of the present time. The bauxitization sequence is postulated in Fig. 1. Pocos de Caldas district is situated at approximately 21" 50' south latitude and 46" 30' west longitude in southwestern Minas Gerais, near its boundary with the state of Sao Paulo. It lies within the Eastern Plateau physiographic province of Brazil, occupying a prominent highland area that rises some 2000 ft above the surrounding country. The central portion of the Pocos de Caldas highland is characterized by gently undulating topography, with generally sluggish drainage, and is surrounded by a rim of hills rising above 1000 ft above it. In cross section the highland resembles a truncated cone with a depressed central area. The rim has been sculptured into a more prominent and abrupt topographic pattern than the central area, and streams that are of low to moderate gradient in the central plateau plunge over the rim in a spectacular series of cascades and falls. GEOLOGIC SETTING The Pocos de Caldas highland owes its physiographic expression mainly to the differential erosion of a complex intrusion of alkalic rocks into gneiss and sandstone. Erosion was guided somewhat by faulting. The highland is almost circular, and its limits, except in one locality, coincide with the periphery of the intrusion. The alkalic intrusions largely control its shape and extent, aided by some subsidence through faulting of the central portion. The mountainous rim of chilled phase, the later intrusions, and the indurated intruded rocks have resisted erosion more effectively than the central portion of the intrusion, which is composed of more coarsely crystalline alkalic rocks that form a central basin in the highland. Gneiss and sandstone are found coincident in elevation with the topographically highest intrusions. BAUXITE TYPES Most of the bauxite, which varies in physical type, is on the top and steep slopes of the northern rim. The only alumina mineral is gibbsite, definitely crystalline but iron-stained unless of secondary origin. Clay particles occurring with the bauxite are kaolinite. Some types of bauxite are an index to their origin. There are four general physical types of bauxite or bauxite laterite: 1) Surface Rubble: This partly nodular and partly fragmented type, usually less than 3 ft thick, results from surface weathering of massive bauxite or may form by superficial enrichment of nodular bauxite with a clay matrix when the interstitial clay is removed by surface runoff.

Jan 1, 1960

By Raymond Mancha

The number of installations of propeller mine fans completed during the years of 1936 and 1937 is evidence of the increasing popularity of the propeller fan with the American mining industry. During the period from 1931 to 1936, there were several different low-pressure, low-efficiency propeller fans available, which filled a definite need in replacing inefficient centrifugal fans operated at comparatively low pressure by means of purchased power. Since 1936, however, the trend toward the propeller fan has greatly increased, as propeller fans are now available practically without pressure limitations and capable of efficiencies high enough to warrant replacement of efficient centrifugal fans in many instances. Few manufacturers of propeller mine fans base their fan-operating characteristics upon similar test methods, primarily because of inadequate facilities for testing in the factory and the need of a test code incorporating a calibrated duct or nozzle that makes possible the testing of large propeller fans quickly, accurately and without prohibitive expense and space requirements. As a result, fan manufacturers have resorted to various methods for testing large propeller fans in the factory, and different yardsticks have produced uncomparable and often inaccurate performance data. It is the purpose of this paper to describe and discuss in detail the test procedure of the Jeffrey Manufacturing Co., which has been proved both accurate and practical. Fig. 1 shows a plan, a side elevation and two end elevations of the test duct with a propeller fan of the exhaust type in place. Testing propeller fans exhausting permits greater accuracy than testing these fans blowing, because in the former uniform flow conditions are more easily established at Pitot tube stations where fan pressure and air-volume measurements are desired. Any residual rotation remaining in the air discharged from a propeller fan blowing into a test duct must be removed before an attempt is made to obtain accurate pressure and volume readings. Although various devices for straightening the air may be placed between the blowing fan and the volume-measuring station without resulting complications, uniform flow so obtained at the pressure-measuring station necessitates corrective calculations to compensate for duct resistance

Jan 1, 1940

By G. H. Lair, B. J. Langford, S. H. Rockwood

Volumetric reservoir analysis is dependent upon a firm relationship between porosity, connate water, and net pay. Capillary presswe data on core samples interrelate these three factors. It is shown that other reservoir problems may be resolved: (I) whether water production is indigenous or extraneous to the oil producing interval, (2) an oil-water contact is being approached, and (3) whether the oil-water contact is remotely situated. INTRODUCTION Volumetric analysis of carbonate reservoirs challenges the ingenuity of the reservoir engineer due to an absence of data on the minimum oil-bearing and oil-producing pores of a given reservoir rock. Many studies with this as the ultimate objective are available on the physical characteristics and fluid-flow behaviors of the carbonate reservoir. Some of these publications are: Hassler, Brunner and Deahl's1 study of the role of capillarity in oil production; Jan Law's' and A. C. Bulnes3 statistical treatment of core analysis data; Chalkley's method4,5 or estimating specific surface areas and porosity; Walter Rose's9 report on porosity, reserves, and recovery; Archie's78 tex-tural classification of carbonate rocks; Stewart and Spurlock's9 large core analysis; Purcell'sl0 mercury injection method in studying capillary pressure phenomena; Stewart, Craig, and Morse's" model multiple-phase flow test in investigating the relative permeability effect; and Fatt's12 illumi-nating network model of porous me-dia. The present study shows that the static reservoir parameters of porosity, connate water, and net productive thickness may be interrelated by utilizing a statistical arrangement of mercury capillary pressure data in addition to routine core analysis. This report summarizes the techniques that are followed to obtain these relations which are applicable to carbonate and sandstone reservoirs that do not contain clays. Capillary pressure statistical studies may be extended to include clay-bearing rocks by utilizing water capillary pressure data. POROSITY It is necessary that the laboratory determine the porosity value that includes the pores that are filled with hydrocarbons and water in the reservoir. This is the reservoir's total porosity. When true total porosity values are not available, correlations between porosity and capillary pressure characteristics lose their significance since they cannot be related through oil-base mud core data to the porosity and connate water values found in reservoirs. Methods used to obtain reliable porosity data will not be discussed; however, care should be exercised in selecting samples for measurement. In homogeneously porous formations, small core plugs sampled frequently will furnish adequate information. Where heterogeneity, particularly vugginess, is present, large-core porosity data may be required; in such reservoirs a suite of capillary pressure samples may be selected from small plugs. CAPILLARY PRESSURE Capillary pressure data provide a method for relating two carbonate reservoir parameters, porosity and connate water saturation, which in turn permit delineation of productive rock types necessary for selecting the third parameter, productive thickness. Specific applications of capillary pressure data to petroleum reservoirs were suggested by Archie8 and Pur-cell."' Their work demonstrated that in preferentially water-wet rock, porc

Jan 1, 1958

By W. F. Mattes

The manufacture of steel rails in the United States upon a large scale may be roughly dated from the years 1875-76, and the same years witnessed an active movement among the railroads toward the adoption of heavier and improved patterns. In this movement each road was a law unto itself, and the "personal equations " of some scores of engineers were so freely injected into the calculations that patterns were multiplied in the most absurd and mischievous manner, until at length the burden upon the mills became wellnigh unendurable, and called forth a vigorous protest in Mr. Holley's paper,* read before the Institute in February, 1881. There were then regularly manufactured in the various mills of the United States, no less than 119 different patterns of steel rails, subject to current order, of which 64 per cent. were embraced under five weights per yard. Commenting upon these and other figures there given, Mr. Holley stated as the primary object of his paper, " to show that,, while this multiplication of rail-patterns is an annoyance and an expense to rail-makers, it is a source of immense loss to railway companies." Since 1876 the increase in gross annual tonnage upon our leading lines has been very great, and has been accompanied by an increase of wheel-loads and running-speeds. As the average weight of the rails of 1876 was by no means excessive, the growing deman Is of traffic have slowly driven the roads toward stiffer sections, inaugurating a movement that now promises to become epidemic. In 1876 a 67-pound rail was a first-class equipment; to-day everything under 75 pounds is light, and many 80's are coming into use. European practice has long been heavier than ours; in part because the higher cost of sleepers has led to an average of 3-feet spacing, instead of two-feet as with us. The old 84-pound double-header, and Sandberg's 80- and 89-pound rails, respectively 51/4 inches and 591/2 inches high, are reported common on English roads; and he is strongly advocating the general adoption of the 100-pounder shown in Fig. 7, with what success I have not learned, except that the Belgian government has ordered a lot. Mr. Sandberg points out the undesirability of frequent changes of pattern, and the recent rapid growth in traffic-requirements; prognosticates a continuance of this

Jan 1, 1887

By W. O. Hotchkiss

Rock exposures are usually a very small part of the surface area in any mining district and the prospector and geologist must base their deductions as to the area, extent, and structure of various formations upon exposures that seldom form 5 per cent. of the area studied. Most often, outcrops form less than 1 per cent. of an area, so that exploration for mineralized contacts or mineral-bearing formations necessitates drilling, test pitting or tunneling, shaft sinking, and other underground work. In these days of high costs any method that will give definite facts regarding rock? obscured by soil or other material should be used to the greatest possible extent. In the early days of the Lake Superior iron districts, mines were located in the few places where ore was present in outcrops. Later, larger orebodies have been found, in depressions, obscured by soil and other foreign material. Mineralized rocks are oftentimes more weathered, softer, and more easily eroded than unmineralized rocks. It is quite natural, therefore, to expect that such orebodies (particularly where large enough to influence erosion in former physiographic conditions) should lie in depressions and be obscured by later debris. It is not difficult to believe that the history of the development of Lake Superior iron mining may be duplicated in other mining districts, that even larger orebodies than those first mined may be found in areas where the rock exposures, which led to original discoveries, are few or lacking. The chief properties of rocks that can manifest themselves through an obscuring cover are magnetism, electrical effects, radio-activity, gravity, and sound transmission. All of these have been used, to a small extent, to tell us a few things about what lies below the surface that we could not otherwise determine, but none has been used so long and so widely as

Jan 1, 1923

By W. O. Hotchkiss

Rock exposures are usually a very small part of the surface area in any mining district and the prospector and geologist must base their deductions as to the area, extent, and structure of various formations upon exposures that seldom form 5 per cent. of the area studied. Most often, outcrops form less than 1 per cent. of an area, so that exploration for mineralized contacts or mineral-bearing formations necessitates drilling, test pitting or tunneling, shaft sinking, and other underground work. In these days of high costs any method that will give definite facts regarding rock? obscured by soil or other material should be used to the greatest possible extent. In the early days of the Lake Superior iron districts, mines were located in the few places where ore was present in outcrops. Later, larger orebodies have been found, in depressions, obscured by soil and other foreign material. Mineralized rocks are oftentimes more weathered, softer, and more easily eroded than unmineralized rocks. It is quite natural, therefore, to expect that such orebodies (particularly where large enough to influence erosion in former physiographic conditions) should lie in depressions and be obscured by later debris. It is not difficult to believe that the history of the development of Lake Superior iron mining may be duplicated in other mining districts, that even larger orebodies than those first mined may be found in areas where the rock exposures, which led to original discoveries, are few or lacking. The chief properties of rocks that can manifest themselves through an obscuring cover are magnetism, electrical effects, radio-activity, gravity, and sound transmission. All of these have been used, to a small extent, to tell us a few things about what lies below the surface that we could not otherwise determine, but none has been used so long and so widely as

Jan 1, 1923

By John A. Garcia

A standard set of coal mining laws for the entire United States is hardly practicsble, yet the numerous variations in the state laws for almost every item seems entirely unnecessary. The same useless variations appear in almost every comparable section with no apparent reason except that no attempt has ever been made to codify them, and as they were developed over a long period of time by innumerable individuals and legislatures, the present situation is the logical outcome of lack of cooperation between states. The ventilation of a mine is affected indirectly by many provisions not listed specifically under this heading, so that it would be necessary to tabulate the major portion of all the laws to secure a complete comparable digest; therefore only a few of the more important have been set down here. This point is well illustrated in the section providing for clearance between car and rib, which is intended as a safety measure against personal injury, but is very important from the standpoint of ventilation because of choked airways in mines on two-entry system. Confusing Phraseology Misinterpretation and confusion may be expected from the phraseology alone; one state provides that the scale of the mine map shall be "not more than 100 ft. to 1 in.;'' another state demands "not less than 100 ft. to 1 in." Both probably mean the same thing and seek to prevent the operator from furnishing a map on which the workings will appear SO small that the detail is illegible. Legislation is certainly indefinite that specifies structures must be fireproof when "near" a mine opening, and just what is a "dusty" or "gaseous" mine is open to argument in most of the states. The variation in spacing crosscuts and break-throughs and the limited number of men on a split seem entirely unnecessary, as the distance is not reduced in gaseous fields, excepting in Arkansas and Tennessee, which states produce a comparatively small amount of coal, and the number of men differs 100 per cent. and more for no apparent reason.

Jan 1, 1927

By Oliver Bowles

WHILE vast quantities of limestone and dolomite are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little attention compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux "that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate dis¬cussion of metallurgical limestone problems.

Jan 1, 1928

By WOOLSEY MCA JOHNSON

INDEPENDENTLY of the recognized chemical reactions involved in the production of metallic zinc, the process is affected by physical conditions in efficiency, and by commercial as well as technical economy. To offer some observations concerning these conditions is the purpose of the present paper. Among the important elements of this problem is the physical nature of the particles constituting the mass of zinc oxide to be reduced. This may be the result, either of the manner of the original deposition of the mineral, or of the treatment to which it has been subjected in the roasting-furnace. The physical character of the reducing-agent is another important factor, since the carbon of some coals is much more active in reduction than that of others. The degree of fineness, whether of ore or coal, or both, likewise plays a significant part. These factors, together with the physical admixture of foreign substances with the ore, may give rise also to chemical "side-reactions," sometimes hindering or retarding, and sometimes accelerating, the reduction. Finally, thermal conditions, including the relative conductivity of the materials, deserve to be taken into account. In firing a furnace with retorts charged with a mixture of roasted ore and coal, the first reaction is naturally the boiling-off of the contained water ; the next is the distillation of the light hydrocarbons from the coal; the next is the reduction of the iron oxide to protoxide and sub-oxide successively, and then to metallic sponge; and the final reaction is the reduction of the zinc oxide in the ore by the carbon to metallic zinc. This reaction commences at 1,022° to 1,060° C., according to the physical nature and condition of the coal and ore. Since the retort and the charge are far from being good con-

Sep 1, 1907

By R. I. Parsons, M. B. Standing, E. N. Lindblad

The recovery of the heavier components from a gas cap or retrograde pool is shown to be the greatest when the sand is cycled with a dry gas at a low pressure. This conclusion is in direct opposition to the belief that the most efficient production program is pressure maintenance and cycling at or near the dew point. The results are calculated from: (I) constant volume, variable composition pressure-volume-temperature tests on a mixture of trap gas and liquid from a producing well; (2) published equilibrium constant data and the measured composition of the dew-point material; and (3) the fact that in a sand section of homogeneous permeability, injected gas displaces reservoir gas nearly, quantitatively. The results are based on the simplifying assumption that variable permeability systems may be defined by the ratio of two statistical parameters, and that gas injected into an actual sand will behave as though the sand were composed of many layers, each of constant permeability. Introduction Pressure decline in gas-condensate type reservoirs is accompanied by the formation of a liquid phase throughout the reservoir. Over the past ten years the processing of the material from these types of reservoirs for the heavier hydrocarbon components and the return of the light fractions to the reservoir ("cycling") has become increasingly popular. It has often been stated that the purpose of such a program is to prevent the loss of the retrograde liquid phase formed in the reservoir. The purpose of this paper is to present the results of laboratory tests and computations concerned with several possible methods of producing a gas cap or condensate type of reservoir. The results show that the recovery of heavier hydrocarbons for this type of reservoir is not a maximum under conditions of cycling at or near the dew-point pressure. Instead, variations in permeability and the ability of the dry injected gas to revaporize condensate, point to cycling at a considerably reduced pressure as the optimum production-method. In addition the paper suggests a way of evaluating sands for their permeability variation. The calculations presented in the following sections of the paper are in terms of the production of the butanes and heavier fraction from the gas cap of a field which had an original pressure of approximately 3000 psi. Specifically, the calculations show: 1. To what extent the condensate formed in the reservoir after pressure decline can be recovered by the cycling of a dry absorber-plant gas through the sands. 2. Whether there would be greater recovery of hydrocarbons if cycling were instigated at the original reservoir pressure.

Jan 1, 1948

By A. B. Cummins

THE past year has been of unusual interest for industrial minerals. It is increasingly evident that requirements for these raw materials move with general economic trends. Thus, with a peak year in the construction, chemical and petroleum industries, the nonmetallic mineral industries have been brought into the complex maze of an economy in which military spending is in the billions and in which the national income and wholesale commodity prices reached new levels. Many industrial minerals are of first rank essentiality in the defense effort and its supporting industries, and since some of these are of limited supply and others dependent on imports, the problems of procurement, distribution and conservation of available supplies make a complicated pattern. Despite some drawbacks and weak spots, the industrial mineral industries have, in general, met the national situation with great credit and many new production records have been set. The general accomplishment in 1951 should be one of satisfaction with confidence for the future. Difficulties, unsolved problems and uncertainties should not obscure the general trend which many consider optimistic. Prices in the main have been upward, in line with the inflation spiral, but nonmetallics appear with some exceptions to be behind the general increases. Labor difficulties have not been serious throughout the year. Retarding influences in expansions and planning have been the uncertainty of the Korean and international situations and a lack of confidence by many in the government economic program and its ultimate impact on the economic structure. It must also be kept in mind that stockpiling, unless all-out war develops, reaches a level and then ceases to be a major sustaining factor in the mineral markets. In accordance with the Defense Production Act of 1950 various control agencies have been set up to establish the desired rate of stockpile acquisitions. The objectives are subject to change depending on availabilities and needs-military, industrial, and civilian. In some minerals there has been disagreement on actual stockpile requirements, and there is some feeling that the needs of defense might be better met if more funds went into the development of new sources of supply of scarce raw materials and more materials were released to industry at this time. Nonmetallic minerals on the strategic and critical list of the Munitions Board as of July 1951 were: Group I; asbestos, some types; bauxite, refractory grade; beryl; celestite; chromite, chemical and refractory grades; columbite; corundum; diamonds, industrial; fluorspar, acid grade; graphite, some types; kyanite; manganese ore, battery and chemical grades; mica, some types; quartz crystals; rare earths; sapphire and ruby; talc, steatite, block; and Group II; bauxite, abrasive; cryolite, natural; diamond dies; graphite, crystalline fines; iodine; mica, muscovite block, stained and lower; rutile; selenium; talc, steatite, ground; zirconium ore, zircon. Details on the current status of stockpiling inventories are not available. The Defense Minerals Exploration Administration has, since April, executed 39 contracts for the exploration of nonmetallic minerals, including twenty for mica, seven for beryl-mica, six for asbestos, three for sulphur and one each for monazite, steatite talc and fluorspar. Total value of these contracts came to $892,059, of which the Government's participation amounts to $689,247. There were on hand at year's end another 97 applications for exploration aid on nonmetallic minerals in twenty different

Jan 1, 1952

By Frank H. Reed, P. W. Henline, Harold W. Jackman

A SUMMARY of the consumption of coal in 1945 shows that the coke industry accounted for 17 pct of the total coal used. No substitute for coke and the blast furnace in the reduction of iron ore has gained sufficient prominence so far to be given serious consideration. However, while the same slot-type ovens are being built and used now as were in use a few years ago, the problem of obtaining suitable coking coals, both high- and low-volatile, has forced many operators to revamp coal-blending facilities. Until the beginning of World War II, high-temperature coke plants were able to secure the required high-volatile and low-volatile coals from two or three seams and from three or four mines. Thus, many of our coke oven plants were able to operate with storage bins for two coals only. The variance in raw materials was not great, and uniformity of blend was a relatively simple problem. Since the beginning of World War II, many and important changes have taken place. Demand for all coals increased greatly. Production, though kept as near maximum capacity as possible, could not meet the demands for coal generally, and particularly for the various kinds of coal which have proved to be satisfactory for specialized uses; coals were allocated as nearly as possible in the order of greatest need; storage piling was reduced to the minimum necessary to keep plants in operation; uniformity of quality could not be maintained, and with this last, uniformity of composition of blends for coking could not be maintained. Whereas before the war producers of metallurgical coke could fill their needs from three or four mines, by the end of the war it was not unusual to find shipments to a single coke oven plant coming from as many as 30 different mines, in a single month. Since many of the mines producing both high- and low-volatile coal for high-grade metallurgical coke are rapidly nearing depletion, the problem of seeking new sources and of blending a number of coals in each plant for the production of high-temperature coke is facing practically every producer in the United States at the present time, and is one which will probably continue for many years to come. Midwestern by-product coke ovens in the Chicago and St. Louis areas use annually from 12 to 15 million tons of bituminous coals which are transported 500 to 700 miles from the Appalachian coal fields of Pennsylvania, West Virginia, and eastern Kentucky. Approximately two-thirds of this coal is high-volatile bituminous. The critical transportation problem confronting the nation in 1943, and the growing scarcity of the best Appalachian coking coals, prompted the Illinois Geological Survey to propose a research program in which would be studied the coking properties of blends of low-sulphur, high-volatile Illinois coal with the high- and low-volatile coals from the eastern fields. Such blends containing Illinois coal, if substituted for the all-eastern blends normally coked,

Jan 1, 1948

By T. D. Murphy

This chapter deals with those types of silica raw materials that have been segregated and refined by natural processes into nearly monomineralic deposits and hence, by virtue of their high degree of purity, have become the sources of commodities having special and somewhat restricted commercial uses. In some instances, these raw materials occur in nature as unconsolidated quartzose sand or gravel and can be exploited and used with very little preparation and expense. More often, they occur as sandstone, conglomerate, quartzite, quartz mica schist, or massive igneous quartz which must be crushed, washed, screened, and sometimes chemically treated before commodities of suitable compositional and textural characteristics can be successfully prepared. The occurrence and distribution of silica raw materials is summarized and an effort has been made to bring commodity definitions, critical properties, and specifications up to date. Presentation of mining and processing methods is considered beyond the scope of this article; they are, for the most part, conventional and well known. New production techniques are currently reported in the trade journals and are later adequately described in technical publications as promptly as competitive restrictions allow. Discussion on Basis of Use ABRASIVE USES Industrial silica used for abrasive purposes falls into three main categories: (a) blasting sand; (b) glass-grinding sand; and (c) stone-sawing and rubbing sand. Blasting sand is a sound closely-sized quartz sand which, when propelled at high velocity by air, water, or controlled centrifugal force, is effective for such uses as cleaning metal castings, removing paint and rust, or renovating stone veneer. It is commonly referred to as Sand Blast sand. Multicycle quartz sand is an efficient blasting agent by merit of its survival characteristics which are soundness, toughness, and hardness. Steel grit and shot have supplanted it to a large extent but owing to their higher cost and tendency toward deterioration in storage, are still not universally used. It is conceded that angularity promotes faster cutting but this is offset by a higher loss in fines. The peening action of a rounded grain is a desirable feature in achieving a satin finish for certain light metal castings but a subangular grain is unsurpassed for fast heavy cutting. Specifications are chiefly based on size frequency distribution but it is mandatory that the grain be free of adhering clay or irony coatings. Material that dusts upon handling will not be tolerated. There is no uniform trade designation for the many blasting sand grades. Most producers sell on the basis of numbered grades; that is, No. 1, No. 2 and so on, this generally connoting fine to coarser grades. Designation of grade by the two sieve sizes between which most of the material lies, is practiced in some areas. Thus, in a No. 1220 grade, 98 pct of the material passes a 12 mesh sieve and is retained on a 20 mesh sieve. Blasting sand specifications vary according to use. Coarse grades range from 4 mesh to 12 mesh, medium grades range from 12 mesh to 30 mesh, finer grades may range from 20 mesh to 100 mesh or finer. Specifications generally call for narrow limits of gradation, requiring precise sizing methods. The fact that most blasting sands are retained

Jan 1, 1960

By M. B. Standing, R. I. Parsons, E. N. Lindblad

The recovery of the heavier components from a gas cap or retrograde pool is shown to be the greatest when the sand is cycled with a dry gas at a low pressure. This conclusion is in direct opposition to the belief that the most efficient production program is pressure maintenance and cycling at or near the dew point. The results are calculated from: (I) constant volume, variable composition pressure-volume-temperature tests on a mixture of trap gas and liquid from a producing well; (2) published equilibrium constant data and the measured composition of the dew-point material; and (3) the fact that in a sand section of homogeneous permeability, injected gas displaces reservoir gas nearly, quantitatively. The results are based on the simplifying assumption that variable permeability systems may be defined by the ratio of two statistical parameters, and that gas injected into an actual sand will behave as though the sand were composed of many layers, each of constant permeability. Introduction Pressure decline in gas-condensate type reservoirs is accompanied by the formation of a liquid phase throughout the reservoir. Over the past ten years the processing of the material from these types of reservoirs for the heavier hydrocarbon components and the return of the light fractions to the reservoir ("cycling") has become increasingly popular. It has often been stated that the purpose of such a program is to prevent the loss of the retrograde liquid phase formed in the reservoir. The purpose of this paper is to present the results of laboratory tests and computations concerned with several possible methods of producing a gas cap or condensate type of reservoir. The results show that the recovery of heavier hydrocarbons for this type of reservoir is not a maximum under conditions of cycling at or near the dew-point pressure. Instead, variations in permeability and the ability of the dry injected gas to revaporize condensate, point to cycling at a considerably reduced pressure as the optimum production-method. In addition the paper suggests a way of evaluating sands for their permeability variation. The calculations presented in the following sections of the paper are in terms of the production of the butanes and heavier fraction from the gas cap of a field which had an original pressure of approximately 3000 psi. Specifically, the calculations show: 1. To what extent the condensate formed in the reservoir after pressure decline can be recovered by the cycling of a dry absorber-plant gas through the sands. 2. Whether there would be greater recovery of hydrocarbons if cycling were instigated at the original reservoir pressure.

Jan 1, 1948

By H. R. Brannon, F. M. Perkins, Weldon O. Winsauer

Both the abnormal resistivity exhibited by shaly reservoir materials and their potential are due to adsorption of ions. Interrelationships between the two have been derived and verified by laboratory results. These relations which have resulted from this work may be used in a qualitative manner to estimate whether or not a particular shaly reservoir contains hydrocarbons, and also to estimate the porosity of shaly sands. INTRODUCTION In spite of the progress which has been made in the last decade toward a better understanding and utilization of the electric log, there remain a number of problems in the interpretation of the log. One of these which is often troublesome is that of divining the nature of the fluids in sandstones or carbonate rocks which contain appreciable amounts of shale. It was shown by Patnode and Wylliel in 1949 that shaly rocks exhibit an abnormally low resistivity when saturated with solutions of low ionic concentrations. This phenomenon has been demonstrated to be due to the adsorptive properties of shale or clay in the rock.' In estimating the fluid content of shaly sands or carbonates from the electric log, it is desirable and sometimes necessary to correct for the abnormally low resistivity. A similar correction is likewise often necessary if attempts are made to estimate the porosity of a stratum from resistivity measurements. The correction may be made from data obtained on core samples and from information on salinity of interstitial water. Cores, however, are not always available. Moreover, even if cores are at hand, their examination is time-consuming. It would be most desirable, therefore, to make corrections of this nature from the log itself. Since both the abnormal resistivity and the potential' are consequences of the adsorption of ions on shale, it should be possible to utilize the potential curve to give better interpretation of resistivity data obtained in logging shaly materials. The work described in following sections was directed toward this end. THEORY Relation of Resistivity of Shaly Reservoir Rock to Adsorpttve Properties In discussing the effect which the presence of shale or clay exerts on the resistivity of a reservoir rock, it is convenient to make use of the resistivity factor.4,5 This quantity has been defined as the ratio of the resistivity of the rock when it is completely saturated with an electrolyte to the resistivity of the electrolyte itself. When the rock, such as a clean sand or carbonate, is free of shale the resistivity factor is virtually independent of the ionic concentration of the electrolyte used to saturate the sample, so that F = R0/Rw = constant for a clean rock . . (1) where F is the resistivity factor, R0 is the resistivity of the rock saturated with electrolyte, and Rw is the resistivity of the electrolyte. When the rock contains argillaceous material, the resistivity factor as defined above is no longer independent of the concentration of the electrolyte used to saturate the rock, but decreases as the ionic concentration of the electrolyte decreases. In explanation of this behavior, it is instructive to consider a sample of shaly porous rock placed in contact with a large volume of a dilute electrolyte. The sample is considered to become saturated with the electrolyte, and to attain equilibrium with it. As a result of adsorption by the shale surfaces within the rock, there is a greater concentration of ions in the solution adjacent to the shale particles in the interstices of the sample than there is in the external solution with which the

Jan 1, 1955

By R. V. Smith, E. J. Dewees, R. H. Williams

Before this paper was presented, the terms "f" and "v1/f in flow equations had been called "friction coefficient" and "friction factor," respectively. However, many authors have used the names for the terms interchangeably, with the result that considerable confusion has existed in the literature on flow of fluids. In an effort to establish a clear and concise terminology for these terms, the authors have designated f as "resistance coefficient" and dm as "transmission factor." Transmission factors for the flow strings of gas wells were determined by tests on wells in six fields of Oklahoma, Texas, and Louisiana. Data were collected on 14 gas wells while gas was flowing through 1 1/4, 2, 21/2, and 3-in. tubing and 51/2 and 7-in. casing. The transmission factors developed from these data were found to follow the resistance equation published by Nikuradse1 for turbulent flow in "rough" pipes with an average absolute roughness of 0.000,65 in. This average absolute roughness is believed to be representative generally of the flow strings of gas wells with the exception of those that have been exposed to corrosion or other conditions causing undue roughness. Also, use of an absolute roughness of 0.000,65 in. probably will result in transmission factors that are more representative of gas-well conditions than those in common use today, provided that the transmission factors are calculated by the methods outlined in this report. The authors believe that use of these transmission factors will permit calculation of more accurate subsurface pressures in gas wells than those in use today. Engineers use transmission factors in flow equations to compute subsurface pressures in flowing gas wells from measured wellhead pressures. These subsurface pressures are necessary for determining the productivity of gas wells from "back-pressure" tests. The methods of calculating pressures in flowing gas wells, as outlined by Rawlins and Schellhardt2 in Bureau of Mines Monograph 7, are based on the transmission factors in the well-known Weymouth formula" Natural gas engineers have realized that errors introduced by using transmission factors as given by the Weymouth formula are relatively unimportant in testing low-capacity gas wells; but they also know that such factors are important considerations in testing large-capacity wells. Accordingly, the research described in this report was undertaken to fulfill the need for more accurate means of calculating subsurface pressures in gas wells. This report is part of the Bureau's study of the flow of natural gas through pipe and commercial pipelines. Several of the conclusions regarding flow in the flow strings of gas wells were influenced by the results of the study of flow in horizontal pipelines. These instances are mentioned in the text of this report. METHODS OF COMPUTING TRANSMISSION FACTORS Methods and procedures for computing transmission factors for turbulent flow in circular pipes from test data taken on gas wells have been derived and explained in detail in a paper by Smith4. As these methods were used to calculate the transmission factors presented in this report, a summary is included. Starting with

Jan 1, 1955

By Henry A. Ley

Kansas ranked fourth on the list of oil-producing states during the year 1930. Progressive statistics show that total production for the year will approximate 42,729,085 bbl. When final figures are compiled for Kansas the production may exceed this estimate, and thereby threaten the all-time record of 43,253,470 bbl. in 1918. Throughout the year the cumulative volume of potential drilled-up production has been increased by new discoveries and by extensions to proven areas in the territory west of the Nemaha (granite ridge) Range. Scattered drilling and leasing operations of a constructive nature occurred, but completions declined to the lowest levels in more than 11 years. Average initial production of current completions climbed to a new all-time high of 512 bbl. to the well. Proration measures were applied to the flush pools. The resulting shut-in potential production, as of December 15, is estimated at 110,000 bbl. This estimate is a wild guess. If all wells of the state were permitted to flow wide open for a period of six months production would not exceed 150,000 bbl. a day. The outstanding development of the year was an intensive drilling campaign in southwestern Kansas, which contributed at least 1,000,000 acres of contiguous natural-gas lands to the natural-gas resources of the United States. Production and Development Prospecting for oil in Kansas began shortly after the initial prospecting at Titusville. Operations and interest in the potentialities became active about 1870. This development was restricted to the shallow districts of northeastern Kansas. By 1895 operations had extended southward to the Oklahoma state line and sufficient prospecting had taken place to prove the potentialities of the state. Active prospecting was extended westward by the discovery of oil on the Nemaha Range in Butler County about 1916. The discovery of oil in Russell County added an extensive borderland province in 1923. The important discoveries of oil in Sedgwick County revived interests and operations throughout this territory in 1928. The development of widespread natural-gas lands in extreme southwestern Kansas during 1930 carried active exploration to the western boundary of the state.

Jan 1, 1931

By T. PH. D. Egleston

THE origin of gold both in placer deposits and in veins, and especially the origin of nuggets, has been the subject of repeated discussions and investigations, which have been recently brought to my attention by several extremely interesting specimens sent to me for examination, and more especially by the one exhibited at the meeting of the Institute in February, 1880.* In the year 1874 I made some examinations of the hydraulic mines of Califor¬nia, and was very much struck with the distribution of the gold throughout these deep placers, which were almost invariably poor on' the surface, while gradually growing richer towards" the bed¬rock. The constant presence of fossil wood, and the large quantity of organic matter contained even low down in these beds, was also remarkable. Not being satisfied with the various theories advanced to account for the formation of these deposits, I began an investiga¬tion early in the year 1879 on the conditions of solubility of gold and the causes of the loss in working gold ore in a large way: The researches which I have undertaken show that gold must be considered a soluble rather than an insoluble metal, and that the conditions of solution are such as will be found anywhere where gold is likely to occur, and the solution may take place even under the ordinary cir¬cumstances of surface drainage, and may be going on freely even where the presence of gold has never been suspected, and that there are causes enough in nature to produce the solution of the gold in sufficient quantities to account for all the phenomena of both the vein and placer formations. The general theory with regard to the formation of these placer deposits and nuggets has been that they were the result of the de¬struction of pre-existing- vein-matter, which does not accord with the facts as shown in the deep placer deposits. The gold in such case would be distributed in layers of unequal richness throughout * Transactions of the American Institute of Mining Engineers, vol. 8, p. 451.

Jan 1, 1881