Search Documents

By Helmer Hedstrom

The purpose of this paper is to direct attention to the importance and the usefulness of phase measurements in electrical prospecting for ore, a subject about which virtually nothing has been published. The paper describes a new field method for ore prospecting, the "Turam" method, which makes use of phase measurements, and which has been used with great success for five years. Of the principal geophysical prospecting methods, the gravimetric and magnetic methods determine the direction and strength of the static fields of force of the earth. By seismic and electrical methods, fields of force are applied to the block of ground under investigation. By these methods a third parameter can be measured, besides the direction and strength of the field; namely, the time of arrival of the applied field at the different observation points. This time of arrival has been practically the only parameter measured in seismic work, while in electrical prospecting it has generally not been considered, the measurements having been limited to determination of direction and strength of the applied field. Phase Measurements In the most widely used of the electrical prospecting methods, those using alternating current, the time of arrival of the "electrical vibration" at the different observation points can be carried out as phase measurements. The phase angle measured then expresses, in part of one "vibration," or one cycle, how much the electrical vibrations at the observation point are out of step with those close to the source of the field. A phase lag of 45", for instance, means that the alternating field in the observation point is one-eighth of one complete " vibration," or cycle, out of step behind the field at the source. If the frequency is, say, 500 cycles per second, a frequency often used in electrical prospecting, a phase lag of 45' then means that the time required for the field of force to travel from the source to the observation point is 1/8 ' /500 = 1/4000 sec. Since the phase angle can be measured with an accuracy of a fraction, say one-tenth, of a degree, and the frequency can be considerably higher than 500, it is readily seen that the time of arrival can in this way be measured

Jan 1, 1940

By B. D. Cullity, S. S. Hsu

The stress distribution at the surface of a twisted cylinder is analyzed along the boundary of a slip plane of arbitrary orientation and this analysis is applied to the torsion of cylindrical crystals of magnesium. A criterion for slip is developed and the critical resolved shear stress of magnesium in torsion is found to be 0.038 kg per sq mm. The mechanism of torsional deformation in magnesium and aluminum is described, as well as the relaxation of a twisted crystal at elevated temperatures. THERE has been considerable fundamental study A of the mechanism of slip occurring during deformation in tension and compression but comparatively little attention has been paid to the mechanism of torsional deformation. This paper is concerned with the way in which a single crystal deforms in static torsion and with the phenomenon of untwisting which a twisted crystal undergoes during annealing. Particular attention is paid to the application of the critical resolved shear stress law to torsional deformation. Probably the most likely mode of torsional deformation that can be imagined consists of rotation of one part of the crystal relative to another on the active slip plane. Here the most interesting feature is the slip direction. If a cylindrical single crystal is twisted about its axis and if, to consider the simplest case, the active slip plane is normal to the specimen axis, then the direction of gross slip at any point must always be at right angles to the radius drawn to that point. It follows that the crystallographic direction of slip must be continually changing, in sharp contrast to slip in tension which occurs in a crystallographically constant direction. Extensive investigations of slip in torsion have been made by Gough and his associates.' They made torsional fatigue tests on metal single crystals belonging to a number of different crystal systems and observed, with a microscope, the appearance of slip lines on the surface and of strain markings on the transverse cross section of cylindrical specimens. They concluded that the critical resolved shear stress law was just as valid in torsion as in tension, in the sense that slip occurred on that plane and in that direction in which the resolved shear stress was a maximum. They also established that the operative slip planes and directions were the same as in tension. They did not, however, measure the critical resolved shear stress in torsion nor, in fact, did they establish that a critical value of the resolved shear stress was necessary for the initiation of slip. Their investigations were, moreover, restricted to torsional fatigue tests which necessarily involve small strain amplitudes. Wilman,' studying crystal growth and the abraded surfaces of crystals, observed crystal fragments

Jan 1, 1955

By Chester Purington

THE AUTHOR hopes that this paper will meet with criticism and debate by fellow members of the Institute rather than with that attitude of passiv-ity and indifference which one is inclined to adopt when considering a field completely foreign to one's own experi-ence. After several years of study of voluminous literature, maps, and statistics, and many personal journeys and field inspections of various parts of Siberia, the conclusion is reached .that the area adjacent to the Stanovoi, Zhugd-Zhur, and Yablonoi ranges as below defined is that which .is most accessible to the western world and will soonest give results from exploration. HISTORY The first incursion of the Russians into Siberia east of the Yenesei River appears to have been in 1632 when the fort of Yakutsk was founded on the middle Lena. The early expeditions were in quest of furs. As the Siberians say, "the sable beckoned" and the post of Anadyr was founded in 1639, two thousand miles further northeast. Thus nineteen years after the Pilgrims landed in Massachusetts, the Russians had established a trading post within 700 miles of what is now the town of Nome, Alaska. Parties of Cossaks penetrated to the shores of the Okotsk1 Sea early in the seventeenth century, but it was not until 1688 that the town of Okotsk was founded. In 1712 a grand project was elaborated at St. Petersburg for building a port at Okotsk, but it came to nothing. Vitus Bering, the Alaska explorer, built ships at Okotsk, and made this his point of depar-ture. It is stated that the iron work used in these ships was brought overland partly from Yakutsk, and partly even from St. Petersburg, 5500 miles away. Accord-ing to report a copper deposit was worked on the river Urak, not far from the coast, and copper was smelted for sheathing the bottoms. Grassgrown mounds con-taining slag and shots of copper were inspected by the writer last summer, at the site of the ancient shipyard.

Jan 11, 1923

By Norman Weiss

The need for more efficient utilization of labor in the metal-mining industry has been the subject of several recent editorials in the mining press, and one attractive possibility for such improvement lies in the designing of future milling plants particularly with economy of manpower in mind. We are accustomed to think of mill design as the selection and coordinated arrangement of process equipment, but if labor is to be efficiently utilized it must be given early consideration in planning the new mill. There are three good reasons for economizing in labor: (I) to reduce costs, not only in the form of wages but also in housing, hospital, welfare, and other obligations that a company accepts when a new man is added to the payroll; (2) to prepare for recurrent periods of manpower shortage, during which a well-designed plant can manage to get along with skeleton crews; (3) because a milling plant that must depend upon an inordinately large labor force for its operation and maintenance is certain to be inefficient in other respects, for many of the shortcomings in design that make necessary the excessive use of labor are generally not corrected merely by having too many men. A simple example of this is a poorly designed ore-feeding system : if this is inadequate to the extent that one man must be constantly unclogging feed chutes, it may help the situation to put two men or three at this task instead of one, but the feed rate will still be inconstant. First of the factors that affect labor saving is the location of the mill. This is often determined by transportation costs alone, and as a result the mill may be placed close to the mine regardless of the nature of the terrain. The designer must then adapt his layout to the conditions, favorable or not. This happens often at small properties, where capital investment may seem more important than operating expense. In most instances, however, a mill site carefully selected for the advantages it gives the designer in laying out the plant is the most economical in the long run, even if it involves a slight increase in cost of ore haulage. Given some freedom of choice, the design engineer may be able to find just the piece of ground that provides the proper gradient for the needs of the flowsheet, permits installation of essential yards and trackage, and perhaps supplies an excellent site for a tailing dam. Further justification for having placed the mill not too close to the mine sometimes emerges only years later as an opportunity to treat ores from other properties. When it is known from the beginning that the new mill will serve a number of scattered mines, a free choice of mill site is naturally stimulated. The most important single factor in limiting the labor requirements of a mill is its materials-handling system for bring-

Jan 1, 1947

By W. F. Holbrook, T. L. Joseph

The problem of sulfur control is important in all blast-furnace operations but particularly for certain grades of steel because of the rigorous specifications. During the past decade the tendency has been to produce pig iron and hot metal of lower sulfur content. As most of the sulfur in the iron originates in the fuel, the use of high-sulfur coke demands modifications in practice to meet sulfur specifications. While it is generally known that high temperatures and more basic slags favor desulfurization, operators as a rule produce the most acid slag that will permit proper desulfurization. The viscosity of blastfurnace slag has been thought to be related to desulfurization and has been investigated by Feild and Roysterl, also McCaffery and his associates*, but apparently no systematic effort has been made to determine the relative desulfurizing powers of slags over the range of composition encountered in practice. Development of Testing Method Because slag and metallic iron are immiscible, the desulfurization reaction is heterogeneous, occurring only at the interfaces between slag and metal bodies. In the blast furnace the newly reduced iron, containing FeS, descends through the slag bath probably either as small drops or streams, at the interfaces of which desulfurization occurs. After its descent through the slag the iron collects to form a bath of metal, at the top surface of which desulfurization reaction probably occurs. These two steps have been thought to account for all desulfurization in the blast furnace. Kinney3 found that metal removed from the blast furnace just above the tuyeres contained three to four times as much sulfur as the iron at cast. Herty and Gaines4 conclude that most of the sulfur is removed while the metal is passing through the slag. Mund, Stoecker

Jan 1, 1936

By Charles A. Anderson

The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a quartz monzonite stock of late Cretaceous or early Tertiary age. This stock, located essentially at the intersection of two dike swarms, is the only one of several stocks cropping out in the area which is appreciably fractured and mineralized. Most of the rocks in the area are of pre-Cambrian age, but their structures have had no discernible influence on the copper mineralization. Hypogene alteration of the quartz monzonite includes the addition of quartz, orthoclase, and sericite and recrystalli-zation of biotite. The hypogene sulphides are pyrite, chalcopyrite, and molybdenite, the latter younger than the chalcopyrite. The late Cretaceous or early Tertiary igneous rocks, veins, and faults were controlled by northeast and northwest shear zones, the intersection of which marks the zone of appreciable copper mineralization. The minor mineralized fractures carrying the bulk of the copper have a preferred orientation parallel to the intersecting shears, and it is concluded that they are of tectonic origin rather than the result of shrinkage on cooling, crystallization, or mineralization. Supergene enrichment during late Tertiary or early Pleistocene time formed a chalcocite zone providing the minable copper ore. The enrichment was controlled in large part by northeast and northwest faults, prticularly at their intersection or where the faults are closely spaced. Introduction A major objective in a regional geologic study of a mining district is to determine whether any structural pattern can be found that has a bearing on the control of mineralization. The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a.quartz monzonite stock which is located essentially at the intersection of two dike swarms (Fig 2). Of several quartz monzonite stocks in the area only this One is appreciably fractured and mineralized. The origin of the minute mineralized fractures in disseminated copper deposits has long been a challenging problem to the mining geologist, and evidence has been obtained to suggest that the mineralized fractures at Bagdad are related to a regional pattern of conjugate shears which also controlled the location of the dike swarms. The purpose of this paper is to Present this evidence and to emphasize the structural control of the supergene enrichment in forming a chalcocite zone that has provided the ore for the Bagdad mine. The field work on which these conclusions are based was done between October 1943 and August 1945, as a part of the copper investigations of the Goelogical Survey, U. S. Department of the Interior. The writer and his associates, E. A. Scholz and J. D. Strobell, Jr., have prepared a comprehensive report on the geology and ore deposits of the Bagdad area which will be published subsequently by the Geological Survey. Bagdad is located in west-central Arizona in Yavapai County. Ransome' divided the State of Arizona into three provinces: I? the plateau to the northeast; 111, the desert region to the southwest and 11, the moun-

Jan 1, 1949

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable—now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advo- cated. The Institute should take the initiative in stimulating this practice. Introduction Training a student in geology for a career in the mineral industry is still a moot question, one that is likely to be looked at from many different angles, each of which will reflect the background of the individual considering it. From what follows, the training of petroleum geologists is omitted since, although theirs is an equally important phase of economic geology, it is based upon different essentials. The general subject was recently effectively discussed, but from a somewhat different viewpoint, by Professor McKinstry.' The practical problems that confront the young mining geologist are highly varied and in the eyes of his employer apparently almost any demands seem justified. The mining executive wants from the mining geologist results related mainly to overall operations, reports or forecasts that are largely recordable on paper and chiefly in terms of "discovery thinking." The local mining engineer may have many specific questions of his own, chiefly relating to details of geology that apply to mining practice, which he will address to the mining geologist; these usually deal with production quantities; frequently also they necessitate the immediate handling of pressing but apparently minor matters: shall the drill be moved; how soon will we encounter the watercourse which made so much trouble for us above? The client employing a consultant often wants advice or good judg-

Jan 1, 1949

By Norman Weiss

The need for more efficient utilization of labor in the metal-mining industry has been the subject of several recent editorials in the mining press, and one attractive possibility for such improvement lies in the designing of future milling plants particularly with economy of manpower in mind. We are accustomed to think of mill design as the selection and coordinated arrangement of process equipment, but if labor is to be efficiently utilized it must be given early consideration in planning the new mill. There are three good reasons for economizing in labor: (I) to reduce costs, not only in the form of wages but also in housing, hospital, welfare, and other obligations that a company accepts when a new man is added to the payroll; (2) to prepare for recurrent periods of manpower shortage, during which a well-designed plant can manage to get along with skeleton crews; (3) because a milling plant that must depend upon an inordinately large labor force for its operation and maintenance is certain to be inefficient in other respects, for many of the shortcomings in design that make necessary the excessive use of labor are generally not corrected merely by having too many men. A simple example of this is a poorly designed ore-feeding system : if this is inadequate to the extent that one man must be constantly unclogging feed chutes, it may help the situation to put two men or three at this task instead of one, but the feed rate will still be inconstant. First of the factors that affect labor saving is the location of the mill. This is often determined by transportation costs alone, and as a result the mill may be placed close to the mine regardless of the nature of the terrain. The designer must then adapt his layout to the conditions, favorable or not. This happens often at small properties, where capital investment may seem more important than operating expense. In most instances, however, a mill site carefully selected for the advantages it gives the designer in laying out the plant is the most economical in the long run, even if it involves a slight increase in cost of ore haulage. Given some freedom of choice, the design engineer may be able to find just the piece of ground that provides the proper gradient for the needs of the flowsheet, permits installation of essential yards and trackage, and perhaps supplies an excellent site for a tailing dam. Further justification for having placed the mill not too close to the mine sometimes emerges only years later as an opportunity to treat ores from other properties. When it is known from the beginning that the new mill will serve a number of scattered mines, a free choice of mill site is naturally stimulated. The most important single factor in limiting the labor requirements of a mill is its materials-handling system for bring-

Jan 1, 1947

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By Benj. N. Webber

There is a broad analogy between super gene nickel deposits and super gene copper deposits of the porphyry type. Some of the nomenclature of supergene copper may he applied to super gene nickel deposits. The obvious connection between lateritization and supergene nickel concentration requires some clarification of the nomenclature of laterite of ultrabasic rock parentage. Lateritization is a progressive process and the transition products of the laterite profile are a key to the process of nickel concentration since the profile grades from unaltered peridotite to the highly ferruginous ultimate laterite capping. This profile is formed under highly restricted geographic and geologic conditions. Faulting contributes to the formation and localization of the higher grade commercial segregations of nickel. That there may be auxiliary sources of nickel other than olivine is suggested. The volume of peridotite necessary to produce a unit of laterite at any point in a complete profile is calculated on the basis of the chromite content. The lixiviation, transportation, and precipitation of the elements involved is considered and the source of the reagents and chemical mechanisms are suggested. The role of sodium chloride is considered important. The progressive changes in the lateritic profile have an effect on the general process since lateritization takes place in overlapping environmental phases. The mineralogy of laterite and the redistribution of elements is illustrated by compositional curves derived from a completely mature laterite. Nickel scanvenged by iron oxides tends to be redissolved and moves downward to the zone of transitional magnesium silicates where it is reprecipitated. The geometry of the nickel enrichment zone is simple in general, but complicated in detail. Elongated pods of a greater concentration of nickel are indicated to be a reflection of faulting. Lateritization and concentration of nickel may be arrested at any stage and be modified by several factors.

Jan 1, 1973

By Pramod C. Thakur

Introduction Methane is contained under pressure within the fractures and adsorbed on the surface of the coal seams and adjacent strata. It is released into the mine atmosphere during mining of the seam creating explosive gas-air mixtures. Large volumes of air, sometimes as high as 20 tons of air for each ton of coal mined, are circulated constantly to dilute and carry away methane from coal mines. Removal of methane from solid coal, wherever high methane emissions occur, has been discussed by Spindler and Poundstone (1960) and Thakur and Davis (1977). Methane control in longwall gobs is much more complicated. As longwall mining progresses, the overburden continually subsides, and the immediate roof caves behind the roof supports. Even the underlying strata heave and open up communication channels feeding gas to the longwall gobs. The pressure of gas in the underlying and overlying strata is usually higher than the ambient air pressure in the mine. Thus the mine workings become natural pressure sinks, into which gas flows from the entire disturbed zone. Winter (1975) defines this zone as the "gas emission space". Depending on the number of gas-bearing zones in the gas emission space and their gas contents, the total methane emission from longwall gobs could vary from a few to more than one hundred cubic meters of gas per ton of mined coal. Hence the ventilation of longwall faces demands a large quantity of air. This ventilation need is further enhanced by high air losses specially on caving faces (with no stowing of the gobs). The old system of longwall ventilation, the 'U' pattern, where all the air was brought down one gate road and exited through the other gate road, loses large quantities of air through gobs giving a high methane concentration at the return end of the face. The 'Y' ventilation pattern where intake air is brought down both head and tail gate roads relieves the situation to some extent but, on most longwalls, some kind of methane control is still needed. With the onset of longwall mining in Europe several decades ago, the initial work on methane control on longwall has naturally been done there. The basic principle of methane control has always been, and still remains, some means of "bypassing methane from the gas emission space without letting it mix with the mine air". In most cases the bypassing mechanism is either a strategically located borehole or a roadway. A successful methane control program depends on the following basic premises: a. Determination of the geometry of the gas emission space and location of gas bearing horizons therein. b. Estimation of the rate of methane influx into the longwall gob. c. A scheme to bypass the gas in the most economic and efficient manner and thus prevent it from entering the mine atmosphere. In successful methane drainage programs a high proportion, usually between 50 and 70 percent, of the total gas emissions in a working district is removed before it can enter the mine airways. Advantages of methane drainage can be summarized as: 1. Generally reduced methane levels in the mine leading to increased safety and productivity. 2. Reduced air requirements and corresponding savings in ventilation horsepower. 3. Faster rate of advance for development headings and economy in the size of headings. 4. Possible use of mine gas as an additional source of fuel. The purpose of this paper is to briefly review the geometry of gas emission space and methane influx therein and discuss more successful European and U.S. longwall gob gas control techniques.

Jan 1, 1981

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable—now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advo- cated. The Institute should take the initiative in stimulating this practice. Introduction Training a student in geology for a career in the mineral industry is still a moot question, one that is likely to be looked at from many different angles, each of which will reflect the background of the individual considering it. From what follows, the training of petroleum geologists is omitted since, although theirs is an equally important phase of economic geology, it is based upon different essentials. The general subject was recently effectively discussed, but from a somewhat different viewpoint, by Professor McKinstry.' The practical problems that confront the young mining geologist are highly varied and in the eyes of his employer apparently almost any demands seem justified. The mining executive wants from the mining geologist results related mainly to overall operations, reports or forecasts that are largely recordable on paper and chiefly in terms of "discovery thinking." The local mining engineer may have many specific questions of his own, chiefly relating to details of geology that apply to mining practice, which he will address to the mining geologist; these usually deal with production quantities; frequently also they necessitate the immediate handling of pressing but apparently minor matters: shall the drill be moved; how soon will we encounter the watercourse which made so much trouble for us above? The client employing a consultant often wants advice or good judg-

Jan 1, 1949

By W. F. Holbrook, T. L. Joseph

The problem of sulfur control is important in all blast-furnace operations but particularly for certain grades of steel because of the rigorous specifications. During the past decade the tendency has been to produce pig iron and hot metal of lower sulfur content. As most of the sulfur in the iron originates in the fuel, the use of high-sulfur coke demands modifications in practice to meet sulfur specifications. While it is generally known that high temperatures and more basic slags favor desulfurization, operators as a rule produce the most acid slag that will permit proper desulfurization. The viscosity of blastfurnace slag has been thought to be related to desulfurization and has been investigated by Feild and Roysterl, also McCaffery and his associates*, but apparently no systematic effort has been made to determine the relative desulfurizing powers of slags over the range of composition encountered in practice. Development of Testing Method Because slag and metallic iron are immiscible, the desulfurization reaction is heterogeneous, occurring only at the interfaces between slag and metal bodies. In the blast furnace the newly reduced iron, containing FeS, descends through the slag bath probably either as small drops or streams, at the interfaces of which desulfurization occurs. After its descent through the slag the iron collects to form a bath of metal, at the top surface of which desulfurization reaction probably occurs. These two steps have been thought to account for all desulfurization in the blast furnace. Kinney3 found that metal removed from the blast furnace just above the tuyeres contained three to four times as much sulfur as the iron at cast. Herty and Gaines4 conclude that most of the sulfur is removed while the metal is passing through the slag. Mund, Stoecker

Jan 1, 1936

By Roswell P. Angier, Herbert S. Kalish, Henry H. Hausner

POWDER metallurgical methods as applied to zirconium are of great interest because they permit not only the fabrication of parts directly to shape with a minimum loss of material but also the utilization of scrap, and the metal may be processed at temperatures well below the melting point. There are two difficulties involved in the melting of zirconium: 1—High vacuum is necessary for melting, and 2—zirconium reduces nearly all oxides so that it is difficult to find a suitable crucible material. The purest material, zirconium crystal bar, is expensive, and the methods of subsequent fabrication are limited. Cold rolling or extrusion of zirconium crystal bar is suitable for making certain shaped parts, but where melting is involved, the purity of the metal is invariably decreased, and a method of casting to a definite shape does not seem to be feasible. Where it is necessary to hot roll, zirconium must be covered with a steel or copper jacket to protect it from the air. This is necessarily a costly operation. Where annealing of zirconium is necessary it must be conducted in a high vacuum. In an investigation of powder metallurgical methods for zirconium, the zirconium powder used should be characterized by the following properties: 1— Highest degree of purity, 2—uniformity in particle shape and particle size distribution, 3—low compression ratio, and 4—satisfactory strength of the compacted powder (green strength). Zirconium powders have been made by two methods: By the reduction of zirconium tetrachloride (ZrC1,) with sodium,2' *•B "nd by the reduction of zirconium oxide with calcium and calcium chloride." The first method represents one of the earliest attempts to make pure zirconium metal, and the sintered product from this powder is extremely brittle. The second method of making zirconium powder is far more successful, but the powder made in this way has an extremely low apparent density and, therefore, a high compression ratio which makes it difficult to use it for powder metallurgical purposes. For these reasons the above-mentioned zirconium powders were not used in this investigation. To obtain sintered zirconium compacts of highest 'purity and good ductility, it was first necessary to produce a suitable powder. Pure zirconium has been made chiefly by two methods. The iodide method, from which the product is "crystal bar" zirconium, was developed first.'." By this purification process very soft, pure, and ductile zirconium metal can be produced. The second method, developed by the U. S. Bureau of Mines, is the reduction of zirconium chloride with magnesium." The sponge zirconium thus produced is also soft, pure, and ductile.

Jan 1, 1952

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By W. A. Tiller, D. H. Lane

A simple zone melting technique for investigating the effect of ultrasonic irradiation upon ingot solidification is described. The effect of i) ultrasonic power level, ii) freezing velocity, iii) constant or variable frequency, iv) direction of irradiation, and v) transducer-cozlpling bar joint upon the grain size of type 316 stainless steel have been investigated. The results of this study support the postulate that the ultrasonic vibrations increase the nucleation probability in the layer of liquid adjacent to the freezing interface. In the first paper of this series,l the possible mechanisms whereby ingot structure may be altered by irradiating a solidifying melt with ultrasonic vibrations have been discussed. A new technique for efficiently introducing the ultrasonic energy into the solid-liquid interface region was presented and applied to ingot preparation by the consumable-electrode arc-melting technique. The experimental results support the postulate that the ultrasonic vibrations may refine the ingot structure by increasing the nucleation probability in the zone of liquid adjacent to the solid-liquid interface. The present paper describes the application of the same technique to a relatively simple laboratory-scale zone-melting apparatus. This apparatus is found to be well suited to the detailed study of ultrasonic technology in this area and allows one to determine, in particular, the minimum ultrasonic power level needed to produce a certain grain size in a particular material. The results of this study support the nucleation mechanism for grain refinement, but do not provide any deeper insight into the specific nucleation mechanism responsible for the effect. EXPERIMENT The apparatus used in these experiments is shown in Fig. 1 and illustrated schematically in Fig. 2. The material to be studied, type 316 stainless steel, was in the form of a 3/4-in. sq bar 30 in. long. This bar was placed in a square open-topped mold with open ends made from high-purity graphite coated with a flame-sprayed Al2O3, skin. Surrounding the crucible was a molybdenum susceptor with 3/8-in. diam holes spaced at 1-in. intervals along its length to serve as sight ports. A tapered transducer horn was brazed to one end of the specimen. The entire assemblage was enclosed in a quartz tube, the transducer itself projecting out one end and resting in a cooling tank. A vacuum seal between the coupling bar and the end plate enclosed one end. A similar plate and seal enclosed the other end. The system is gas tight and can be operated under vacuum or an inert atmosphere. For these experiments, flowing argon at 15 in. of Hg pressure was used. The heat source for melting the stainless steel specimen was a 2-in. long 3-kc induction coil placed around the quartz tube; this source heated the susceptor, inductively melting about a 3-in. zone of the sample by radiation. To move the molten zone at a specified rate, the induction coil was moved down the tube at this rate with the aid of a simple pulling device. Thus, the sample could be irradiated at varying ultrasonic frequencies and power levels and could be solidified at varying rates. The power input to the transducer was measured using a "John Fluke Model 120 VAW-Meter." 1 The power delivered to the interface region is probably only about 50 pct of that measured on the VAW-meter. In a typical run, when the ultrasonic power was turned on, the interface of the molten zone closest

Jan 1, 1961

By E. O. Jones, E. Whitehead

During the heating of cold-worked nickel silver, the tendcncy of the material to crack is well known. The present research deals with this question, and may conveniently be divided into the following sections: Changes in these alloys during heating and cooling, determination of the temperature at which cracking occurs, effect of grain size, quenching cracks, methods of overcoming annealing cracking. The work is far from complete, in particular the influence of impurities on this tendency has not been investigated, but the results so far obtained lead to certain definite conclusions, which are of theoretical and practical importance. Changes in Alloys During Heating and Cooling During the annealing of many metals at a temperature just below that at which recrystallization sets in, there is evidence of some change, the effect of which is to harden and embrittle the material. This effect has been most clearly demonstrated in the cases of aluminum, copper, brass, and nickel silver, and appears to be a common property of cold-worked metals and alloys, or, at any rate, the non-ferrous ones. The effect would obviously offer an explanation for certain types of annealing cracking, but the trouble is so much more common in the nickel silvers than in the other alloys that some special cause should be looked for. There is, however, fairly good reason for believing that similar cracking may occur in some of the brasses; D. Bunting1 suggests that the a brasses toward the saturation limit are subject to a transformation closely allied in nature to that known to occur in the nickel silvers at around 320" C. Although the existence of this critical temperature range was known, it did not necessarily follow that this transformation was responsible for the trouble under investigation, so the first portion of this paper deals with the attempts made to determine whether other critical changes might not occur in these alloys. There were already reasons for the belief that such would prove to be the case, as the mechanical properties of the nickel

Jan 1, 1926

By Jr. J. L. Ryon.

Experimentation with ammonium nitrate-fuel oil mixtures at three underground salt mines revealed its excellent applications at those properties. The author relates the present blasting practice used at these mines by the Intemzational Salt Co. The International Salt Company is presently performing blasting operations with a pneumatically -placed ammonium nitrate-fuel oil mixture at three rock salt mines, and plans its use in the near future at its new Cleveland mine. Use of ammonium nitrate is saving the company approximately $250,000 annually. With rapidly increasing operating expenses and increasing competitive pressure resulting in lower prices, savings such as those realized through the use of ammonium nitrate are vitally important. ORIGINAL INVESTIGATION AND EXPERIMENTAL ACTIVITIES The three mines presently involved are located at Detroit, Mich.; Avery Island, La.; and Retsof, N. Y. Initial experiments were conducted at the Detroit mine where a detailed investigation was carried on to determine the significance of the static electricity factor when blowing ammonium nitrate into drill holes in which millisecond delay electric blasting caps had been placed. Although the information developed at the Detroit mine was passed along to the other mines, each mine independently pursued its own course of inves- tigation. This fact, plus the differing mining conditions, resulted in slightly different operational procedures at each mine. Some of the varying statistical data are shown in Table I, and data common to all three International Salt Company mines are shown in Table 11. BLASTING PROCEDURE AT THE DETROIT MINE This mine has been using the ammonium nitrate-fuel oil mixture for more than two years on a full time production basis and represents the successful detonation of several hundred thousand holes. Results have been excellent and the blasting cost has been reduced many times. The actual operation at Detroit consists of adding the fuel oil to the bags of ammonium nitrate by means of a portable fuel oil tank complete with hose, nozzle, and metering device. The bags of the ammonium nitrate-fuel oil mixture are transported to the working face from the oiling area by means of a jeep-drawn trailer. At the face, the ammonium nitrate is placed on the elevating platform of a powder-load ing rig which consists of a pneumatically-tired, large fork-lift truck with a fully insulated elevating platform constructed on the forks. The placement of the dynamite primer and the pneumatic placement of the ammonium nitrate is a two-man operation. First, one cartridge of the primer is placed in each hole on the line of holes which can be reached from the loading rig platform. The plastic hose is then inserted into the hole and pushes the primer to the back of the hole. The proper charge of ammonium nitrate is then placed in the pneumatic placement machine and,

Jan 1, 1961

By Charles A. Anderson

The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a quartz monzonite stock of late Cretaceous or early Tertiary age. This stock, located essentially at the intersection of two dike swarms, is the only one of several stocks cropping out in the area which is appreciably fractured and mineralized. Most of the rocks in the area are of pre-Cambrian age, but their structures have had no discernible influence on the copper mineralization. Hypogene alteration of the quartz monzonite includes the addition of quartz, orthoclase, and sericite and recrystalli-zation of biotite. The hypogene sulphides are pyrite, chalcopyrite, and molybdenite, the latter younger than the chalcopyrite. The late Cretaceous or early Tertiary igneous rocks, veins, and faults were controlled by northeast and northwest shear zones, the intersection of which marks the zone of appreciable copper mineralization. The minor mineralized fractures carrying the bulk of the copper have a preferred orientation parallel to the intersecting shears, and it is concluded that they are of tectonic origin rather than the result of shrinkage on cooling, crystallization, or mineralization. Supergene enrichment during late Tertiary or early Pleistocene time formed a chalcocite zone providing the minable copper ore. The enrichment was controlled in large part by northeast and northwest faults, prticularly at their intersection or where the faults are closely spaced. Introduction A major objective in a regional geologic study of a mining district is to determine whether any structural pattern can be found that has a bearing on the control of mineralization. The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a.quartz monzonite stock which is located essentially at the intersection of two dike swarms (Fig 2). Of several quartz monzonite stocks in the area only this One is appreciably fractured and mineralized. The origin of the minute mineralized fractures in disseminated copper deposits has long been a challenging problem to the mining geologist, and evidence has been obtained to suggest that the mineralized fractures at Bagdad are related to a regional pattern of conjugate shears which also controlled the location of the dike swarms. The purpose of this paper is to Present this evidence and to emphasize the structural control of the supergene enrichment in forming a chalcocite zone that has provided the ore for the Bagdad mine. The field work on which these conclusions are based was done between October 1943 and August 1945, as a part of the copper investigations of the Goelogical Survey, U. S. Department of the Interior. The writer and his associates, E. A. Scholz and J. D. Strobell, Jr., have prepared a comprehensive report on the geology and ore deposits of the Bagdad area which will be published subsequently by the Geological Survey. Bagdad is located in west-central Arizona in Yavapai County. Ransome' divided the State of Arizona into three provinces: I? the plateau to the northeast; 111, the desert region to the southwest and 11, the moun-

Jan 1, 1949

By M. R. Goldick

The Roan Antelope concentrator was originally designed with a nominal milling capacity of 6000 tons of copper ore per day but this was subsequently considerably exceeded. In broad outline the plant consisted of two No. 30 McCully gyratory crushers for coarse crushing, five 5½-ft Standard Symons crushers in open circuit for secondary crushing, ten No. 98 Marcy ball mills arranged in five sections, each two-mill section with primary and secondary Dorr classifiers for two-stage grinding. One stage of flotation roughing was followed by two stages of cleaning, all in airlift type pneumatic flotation machines, with the final concentrates filtered on Oliver drum filters. Tailing was thickened in a 250-ft Dorr traction type thickener before pumping to the tailing dam. Concentrating operations commenced in June 1931, on the completion of the first two ball-milling sections and output was increased during the next few months as the remaining sections were finished. From the start, very few technical difficulties were experienced but a number of evolutionary changes have been made as a result of operating experience and the availability of improved equipment. These have resulted in plant and ore-flow alterations although the general scheme of ore treatment remains substantially as before. The main changes to date were the installation of a new crushing plant at Storke shaft, some 7000 ft west of the original Beatty shaft; the completion of a two-stage secondary crushing plant; an increase of 20 pct in ball-milling capacity; a change-over from pneumatic to a mcchanical type of flotation machine for flotation roughing; the reduction of flotation cleaning from two stages to one stage. Ore Treated Typically the ore treated consists of metamorphosed shales and sandstones with shales as the principal mineral-bearing rock carrying chalcocite, bornite and chalcopy-rite as the main copper minerals. Chalcocite predominated in the original eastern end of the ore body but there is a pronounced trend to an increased proportion of the copper-iron sulphides as mining proceeds westward. Although the ore can be described as soft, this advantage is offset by the extremely fine dissemination of the copper minerals which calls for a high degree of comminution of the ore (go pct minus-zoo mesh Tyler standard) to give a reasonably satisfactory separation of mineral from gangue. Latterly, there has been a tendency for the ore to become harder as shown by a reduction in the ball-milling rate from a previous figure of over goo tons per ball-mill day to the present output of some 800 tons. Chalcopyrite is not so finely disseminated and has also proved more amenable to flotation than chalcocite. Nonsulphide minerals are mainly the so-called oxides such as malachite, cuprite and melaconite with some chrysocolla and

Jan 1, 1949