Search Documents

By Philip H. Nelson, Richard Lingle

Vibrating wire stressmeters (VWS's) and borehole deformation gages (BDG) were deployed in two in-situ heater experiments at Stripa, Sweden to determine the thermally induced stress changes in the rock mass. The heater experiments ran for 18 months, including a six- month cool-down period after the heaters were turned off. Gages were installed in both horizontal and vertical boreholes and were subjected to temperatures ranging from 10°C to 120°C, depending upon the distance of a gage from the central heater. Most gages operated in a moist environment because groundwater flowed into many of the instrument boreholes during the experiments Of the 36 VWS's installed, six failed. Failures were attributed to corrosion of the vibrating wire due to moisture entering the gage body. Of the 30 BDG's installed at the beginning of the experiments, 22 failed, also as the result of water entering the gage body. Modification and reinstallation of the gages eliminated the problem of water infiltration, but much data from early stages of the experiments was lost due to gage failures. Calibration of the VWS in blocks of Stripa granite showed a lack of repeatability. Variability in calibration results are attributed to seating effects, to variations in the elastic modulus of the rock, and to changes in temperature. These three effects combined to produce an error judged to be approximately ±33% of the stress changes measured at Stripa. In contrast, the major source of error in determining stress with the BDG appears to be the uncertainty in rock modulus and thermal expansion coefficient. Sample calculations based on data acquired near the end of the experiments (during cool-down)

Jan 1, 1982

By D. Walton, W. C. Winegard, W. A. Tiller, J. W. Rutter

It is shown that the cellular substructure observed in binary alloy crystals grown from a melt of known concentration can be eliminated by the proper choice of growth conditions. For a given solute concentration, there exists a critical ratio of temperature gradient G in the melt to the rate of solidification R of the crystal, i.e., of G/R, which must be exceeded before the cellular structure can be eliminated. A secondary substructure is observed which is related to the cellular substructure. IN crystals grown from the melt, a prismatic substructure has been observed by Buerger,1 Pond and Kessler,2 and Rutter and Chalmers." This structure is columnar in the direction of growth and appears as a network of hexagonal cells in the plane of the solid-liquid interface. Rutter and Chalmers3 have shown that this substructure occurs as a result of the presence of a layer of high impurity concentration in the melt adjacent to the solid-liquid interface. The formation of the substructure is accompanied by a redistribution of this impurity in the neighborhood of the interface. The structure can be controlled by proper adjustment of the variables in the solidification process such as a rate of solidification and the temperature gradient in the liquid. The redistribution of solute during the solidification of metal crystals has been treated theoretically

Jan 1, 1956

By F. W. Gordon

Since the waste gases of the blast-furnace came to be generally utilized in heating the blast and raising steam, the gradual improvement in the economy of fuel, mainly through the nse of higher temperature in the blast, has impoverished the gases. The increased output per unit of measurement of the furnace, and the increased height of the furnace, have markedly increased the resistance to the blast, thus enormously increasing the duty required from the gases. In other words, a gas reduced in heating power by a further dilution of CO, is required to raise the temperature of the blast to 1800' Fahr., where formerly 600' was a good temperature, and at the same time to raise steam enough to drive the air into the furnace at a pressure of from four to eight pounds in coke practice, and from eight to twelve pounds in anthracite practice, and also pump at least double the water formerly used at furnaces. Hence the necessity for the employment of the best scheme for thoroughly consuming these gases with the least dilution of air, and the use of the best device for absorbing the heat prodnced for the purposes above mentioned. In a former paper before this Society the writer called attention to such improvements as had been made by his firm, by which it was claimed 1400' Fahr. could be maintained in the blast by a less consumption of gas than was required to maintain 900' when using pipe-ovens; and it would not be too much to say that 1600' Fahr. might now be written in place of the 1-400. The object of this paper is to give the practice of our firm in the

Jan 1, 1884

By Hans Haalck

PRACTICAL or applied geophysics-as we designate the border region between physics and geophysics on one hand and practical geology on the other-has as its object the application of physical or geophysical methods of investigation to problems of practical geology. Its field of operation comprises all methods of physical measurement that are used in the problem of determining, from the geophysical influences of the subsoil that can be measured at the surface of the earth, the special characteristics of the association of strata, faults, etc., to detect the presence of deposits and to investigate underground structures. It therefore represents an aid, a physical method of research in practical geology, and is inseparably connected with geological studies; for this reason, it is also called geophysical prospecting. Formerly research methods of practical geology were based on observation exclusively: first, on the observation of the strata and formations at accessible tarts of the surface of the earth, especially in shafts, borings and mines if such were available; then on the observation of the tectonic conditions in so far as these were already known at places directly visible; and finally, by estimation of the importance of formations of the terrane. Later, there were added in special cases, analytical chemical crystallographical, petrographical and similar investigations of rock samples which were taken from the places under consideration. The knowledge thus obtained is of value and is expanded by hypotheses and constructions that are supported by geological theories of origin and by laws of the sequence of formations and rock systems, which are based on long experience.

Jan 1, 1928

By Victor G. Hills

This paper comprises suggestions on certain points rather than a complete survey of the whole subject. In other words, it is a contribution to the kenera1 discussion invited by John Hays Hammond in his paper, presented as a Presidential address at the Chattanooga meeting of the Institute, in October, 1908.1 Mr. Hammond says, in conclusion: "... I am not offering a code, or even an official and representative declaration of principles.. My remarks are intended, and will, I hope, be accepted, simply as a contribution to that discussion of their theme in which every engineer of experience may participate." Such a discussion has been conducted in technical journals, as well as in contributions to the Transuctions of the Institute; and, in the remarks here offered, I shall have occasion to refer the read& to what I have thus published elsewhere, for more extended statements of my views. What Mr. Hammond says about loyalty to employers, the double capacity of the engineer as an employer, the expert witness, commissions on machinery, the statement that most swindling is done by laymen and not by engineers, duty to the investing public, and the engagement of local engineers as colleagues, it is a pleasure to indorse. Under the head of the expert witness, Mr. Hammond refers to the address of Dr. R. W. Raymond on Professional Ethice. This paper con-

Jan 1, 1911

By B. Stas, L. Siska, L. Dlouhy, A. Skrabis

The basic research program of the Scientific Coal Research Institute at Ostrava - Radvanice into the problem of geophysics has been influenced by the specific nature of present urgent geo- physical problems in mines and directed to attain higher grade of effectiveness, safety, and overall economy in mining activity. The research has been divided into two basic trends: Seismoaccoustic research deals with questions pertaining to safety in mining especially when work is in coal seams under "heavy roofs", i-e., thick beds of sandstone prone to rock bumps and characterized by caving. Methods have been developed with the definite aim to determine the time and space prognosis of critical states of tension in the rock mass when stability is disturbed as a result of mining activity. Seismic research is directed towards the determination of detailed structural and tectonic elements of the internal geological formation of the Carboniferous rocks, the establishment of continuity or tectonic faulting of coal seams, and the evaluation of magnitude, shape, and time changes in the rock mass surrounding the mine workings. The measurements have been applied either from the surface or in the underground workings according to the specific nature of individual problems. Satisfactory results have been obtained in some branches of this research, other branches being still in the stage of development. Remarkable results have been achieved in the development of seismoaccoustic methods designed to establish the time prognosis of dangerous dynamic phenomena accompanying the process of strata deterioration above the worked longwall face. One of the most

Jan 1, 1971

By Ronald F. Ayers

The basic research for this study was conducted by Battelle's Columbus Laboratories in 1974. The high-sulfur content of coal threatens to erode its competitive position in the future. The impact of sulfur removal on final costs of eastern interior coal lies at the very heart of this market analysis. An extensive market survey was conducted that considered both traditional coal markets as well as anticipated future markets. Competition for coal from this province considers low-sulfur Western coal, nu- clear power, international oil and coal trade, as well as Appalachian coal producers. Based on projections of future energy consumption under several scenarios, a comprehensive market forecast for eastern interior coal was made to 2040. The study upon which this paper is based was completed by Battelle's Columbus Laboratories for the U.S. Army Corps of Engineers in 1974. It is but part of an overall effort by the Corps to evaluate the costs and benefits to the nation of waterway improvements. This study is primarily concerned with future coal markets for production from those counties near the Wabash River in the heart of the Eastern Interior Province. An objective here is to consider a most pessimistic energy (and hence, coal) demand for planning purposes.

Jan 1, 1978

By J. T. Price

The study was undertaken to investigate the effect in the charge to a blast furnace of zinc and alkali contents, which tend to form accretions and scaffolds in the upper sections of the furnace. Commercial iron oxide pellets were reduced in a CO:N2, 40:60 gas mixture in a 5-cm by 5-m counter-current reactor (Rist-type apparatus) designed to simulate blast-furnace conditions. Pellets from a commercial magnetite concentrate were prepared in the laboratory with zinc (1% ZnO) and alkali (1% KOH) additions to the concentrate. Reducibility, crushing strength and swelling tests were carried out and the results compared with test data from pellets prepared without additions. The results indicated normal behaviour for those pellets containing zinc, whereas those containing alkali swelled catastrophically under the same reducing conditions.

Jan 1, 1977

By Louis D. Huntoon

The Hammond Mining and Metallurgical Laboratory is the gift of Prof. John Hays Hammond to the Sheffield Scientific School of Yale University. Professor Hammond was graduated from this school in the class of 1876, and has always shown great Merest in its welfare and progress. In 1903, he offered to build and equip for it a mining and metallurgical laboratory. This offer was gratefully accepted by the trustees; and in October of the same year the architect, W. Gedney Beatty, and I were employed to draw up plans for the building, which is the largest of its kind in this country. The Treasurer's report shows the total gift of Professor Hammond, including land, building, and equipment, to have been $128,741.53. This does not include $5,000 given by Professor Hammond to defray incidental expenses. The detailed cost of the machinery and installation, included in the above sum, is as follows: Macbinery,.......$9,846.00 Pipe and fittings,......925.05 Hangers, shafting, pulleys, belts, etc.,.. Steel-work, tanks, launders, etc.,...272.19 Screens for sizing ore,.....411.37 Lumber,.......1,896.36 General Supplies : Hardware,......$135.96 Tools,.......263.66 Paints,.......204.63 Electric and incidental,.... 439.57 ----------1,043.82 Machine-shop material, . 259.44 Labor,.. 722.29 ----------981.73

Jan 1, 1910

By W. C. Schroeder

PRACTICAL experience has shown that at elevated temperatures solu-tions containing sodium hydroxide may attack stressed steel in a manner that cannot be explained in terms of ordinary corrosion. Because the ductility of the metal has been greatly reduced during the reaction, the entire phenomenon is usually called "embrittlement." Thus, after several years of operation caustic evaporators have been so badly embrittled that rivets could be cracked off with the blow of a hammer. Since fine intergranular cracks are almost always present in the zone of fracture, it has often been assumed that a process of selective corrosion in grain boundaries was responsible for the failure, although this has not been clearly proved experimentally. Concentrations of sodium hydroxide below those necessary for the uniform, rapid attack of the steel surface are reported to be most effective in producing embrittlement2,3. In the operation of steam boilers a similar type of failure has been found, mainly in riveted seams or other capillary spaces where the solu-tion may concentrate and where high stresses may also exist. It is believed that in such localized areas the dissolved solids may reach a value many times the few hundred parts per million prevalent in the body of the boiler. While this type of boiler failure has been the subject of investigation for a period of 20 years', an understanding of its mecha-

Jan 1, 1936

By Donald E. Crowell

In the fall of 1969, ASARCO and Newmont Mining Co. began the design of the 700tpd concentrator at their Black Cloud shaft located near Leadville, Colo. The concentractor would treat by flotation a Pb-Zn-Ag ore containing minor gold values. Flowsheet design was based on laboratory test work performed at the Minerals Research Testing Laboratory of ASARCO. Since the concentrator is located at an elevation of 11,000 ft, cold weather was a major factor in design considerations. The original capacity was designed as 700 tpd but for various reasons an ultimate capacity of 1,000 tpd was desired. This necessitated special consideration in the design of several areas, particularly the grinding circuit. The grinding circuit chosen was a single 9 X 12 ball mill operating in closed circuit with one 20-in. cyclone. The ball mill will operate at low speed and as an overflow type originally. The mill can be speeded up and converted to grate type for handling the larger tonnage when required. Thickeners and filters were oversized and space was left for additional flotation cells in order to handle the increased tonnage in these areas. Pumps were sized so that they could handle the increased tonnage by increasing their speed. Construction began in May 1970; the Black Cloud concentrator went on-stream in April 1791.

Jan 1, 1974

By M. R. J. Wyllie

The relationship between the electromotive force (E.M.F.) across a shale barrier and the concentrations of sodium chloride solutions on either side has been investigated. It is shown that the action of a shale barrier is analogous to a glass membrane separating two acid solutions of different hydrogen ion concentrations. The shale behaves as a sodium electrode and is responsive to the activities of the sodium ions in the two solutions in such a way that the potential can be calculated by means of the Nernst equation. This conclusion is confirmed by laboratory experiments. In a borehole the total E.M.F. of a shale cell is the algebraic sum of the ~otential across the shale and a boundary potential. The relationship between total E.M.F. and the resistivity ratio of two sodium chloride solutions is indicated for a number of formation temperatures. The E.M.F. thus predicted is then compared with the .elf potential read from an electric log and good agreement is demonstrated. Based on both the self potential and resistivity curves of the electrical log. a method is given for calculating connate water content in a bed having in-tergranular porosity and containing both connate water and hydrocarbons. INTRODUCTION The first paper on electrical well logging by C. and M. Schlumberger and E. G. Leonardon in 1934' attributed the self potential curve principally to streaming potentials, i.e. to electroki-netic effects. Almost immediately great difficulties were encountered in reconciling many of the curves they obtained with this interpretation. and a ~econd paper' by the same authors soon appeared. In this second paper self potentials were attributed to the combined effects of streaming potentials and electrochemical potentials, the electrochemical potential being considered the result mainly of the interaction of fluids of differing salt concentrations, i.e. a boundary potential, and partly of potentials set up at the faces of impermeable materials. Some experiments involving a gray clay for the impermeable material were quated. The Schlumbergers and Leonardon deduced from the equation for a simple boundary ~otential that the electrochemical potential, as opposed to the electrokinetic potential, could be expressed in the form E=Klog- .......1 pe where K is a constant, pm the mud resistivity. p, the resistivity of the connate water in a porous bed. However, no general expression for the constant K was obtained. Although the literature between 1934 and 1943 contains a number of quotations of their results, the valuable work of the Schlumbergers and Leonardon was not extended so that the electrochemical potential has been generally attributed wholly to boundary potentials between the mud in the borehole and the connate waters in porous formations. Unfortunately, however, the fundamental premise of all these papers, that a boundary potential can give rise to current flow in a borehole, is thermodynamically untenable. As will be shown. the fact that the electrochemical potential can be fairly accurately express as E = K log pm/pc, a form in which a boundary potential may also be written, is partly fortuitous. The boundary potential is indeed an integral part of the expression for the electrochemical potential in a horehole, but in magnitude it represents only about 20% of the total potential. In 1943 an important step in the elucidation of electrochemical potentials was made by Mounce and Rust3 who showed that if a wall of shale separated two compartments which contained saline solutions of different concentrations, and if the two solutions were themselves brought into contact in the pores of a porous inert membrane (such as unglazed porcelain) a current flowed through the shale and saline solutions. The direction of positive current was from the shale into the more dilute solution. The paper of Mounce and Rust, while repeating some of the observations of the Schlumbergers and Leonardon, seems to be the first to show that the shale was the seat of a genuine electrochemical effect capable of causing current flow. In the same paper Mounce and Rust pointed out the similarity between the fundamental conditions of their experiment and the conditions which existed when a bed of shale in the ground was simultaneously in contact with a porous sand containing saline connate water and mud fluid of salinity different from that of the water in the sand. Since it is now generally recognized that the S.P. curve measures ohmic potential changes in the mud fluid in the well bore resulting from changes in current flow, it is apparent that currents having their origin in the electrochemical interaction of mud filtrate and connate waters with shale beds are a very important portion of the total S.P. The work of Mounce and Rusta and others appears to indicate that, in general, the electrochemical portion of a particular kick on a S.P. curve far exceeds any electrokinetic potentials resulting either from streaming potentials or Dorn effects. The Dorn effect, or sedimentation potential. arises when small particles are allowed to fall through certain fluids under the influence of gravity. a difference of potential being observe? between two electrodes placed at different levels in the stream of falling particles. The Dorn effect is unlikely to affect seriously the S.P. curve as now measured. A successful analysis of the electrochemical aspects of the S.P. log should

Jan 1, 1949

By H. I. Aaronson, C. Laird

The kinetics of thickening and of lengthening of ?' plates in an Al-3.93 pct Cu alloy in the temperature range 203" to 300" C were determined by means of transmission electron microscopy. The rate of thickening was found to be less than that allowed by volume diffusion control at all temperatures, by amounts which increased with decreasing temperature, in agreement with the predictions of a general theory of precipitate morphology.1 Thickening was treated on the basis of the ledge mechanism. Ledges were deduced to spread across the broad faces of ?' plates at volume dzjrfusion-controlled rates, as anticipated from the disordered structure of their edges. Lengthening of 8' plates, on the other hand, took Place more rapidly than allowed by volume dzjrfusion. This occurred despite clear morPhological evidence of a bmrier to growth at the edges of these plates. It was concluded that the misfit dislocation structure comprising the barrier requires that lengthening take place by a jog mechanism. The tnisfit dislocations, however, also serve as diffusion short circuits, and allow high overall lengthening rates to be achieved. In Part I' it was shown that, within the range of aging temperatures and times studied, the broad faces of 8' plates formed in Al-4 pct Cu are fully coherent with the a, matrix. Virtually .all of the dislocations present in these faces were found to have developed as a result of plastic deformation in the a phase. Such dislocations are thus "intruders", rather than the more usual misfit-compensating variety. The edges of 8' plates were confirmed, by extension of the earlier studies of Mat-suura and Koda,3 to be made up of edge-type misfit dislocations, in sessile orientation with respect to lengthening of the plates. These interfacial structures should cause 8' plates to thicken and to lengthen at rates less than those allowed under the condition of volume diffusion control, such as would be expected if the interphase boundaries had disordered structures.' The narrow width of 8' plates, the reproducible crystallography of their broad faces, and the appearance of these plates in cross section as octagons rather than as circular discs2 provide qualitative support for these deductions. The present study of the rate of thickening and the rate of lengthening of 8' plates was undertaken in order to examine them on a quantitative basis. I) THICKENING KINETICS OF THE BROAD FACES OF?' PLATES A) Literature Review. The measurements now available on the thickening kinetics of single-phase precipitate plates consist of one plot of the thickening of a proeutectoid ferrite plate in an Fe-C alloy,' showing (as predicted) thickening rates less than those allowed by volume diffusion control. B) Experimental Procedure. Details of the preparation of the 4-3.93 pct Cu alloy used in this study have been previously reported.4 As in Part 1,' transmission electron microscopy was the observational tool employed. A general description of the apparatus and procedures of the electron microscopy studies is given in Section I of Part I. In thin foils, 0' plates tend to form at and parallel to the foil surface.' A direct investigation of the thickening process by means of hot-stage transmission electron microscopy was therefore not feasible. It was thus necessary to use the conventional method of aging individual bulk specimens for a wide range of different times at the various temperatures studied. In each specimen, the thicknesses of a number of plates were measured. Since thin foils prepared from "bulk-aged" material contain a large proportion of grains with orientations near (001) , it was relatively easy to find, near the edges of the foils, the characteristic multifold patterns of intersecting extinction contours which indicate regions where the foil is exactly at an (001) orientation. The thicknesses of large numbers of plates were measured along the (200) branches of the "stars" so that the 8' plates were precisely parallel to the optical axis of the microscope. Wherever possible, intersecting extinction contours were adjusted with the parameter s > 0 to improve the visibility of the plates in bright-field illumination. These precautions, in combination with taking the measurements at the thinnest parts of the foils, minimized the errors in the measurement of the thickness of the plates resulting from inexact parallelism to the electron beam. Since the plates were very thin, it was not easy to measure their thickness on the photographs. The techniques of enlargement and of microdensitometry were employed to minimize errors from this part of the measurement. A further source of possible error, that the plates can appear thicker because of contrast associated with mismatch normal to the plane of the plate, was also considered. The images of the plates were usually thinner than those of dislocations, however, and no anomalous changes in apparent plate thickness were observed when regions of foil containing plates were tilted through various diffracting conditions. Any error from this cause must therefore be small. Other sources contributing errors were: a) the microdensitometer traces per se and the subjective estimates of their peak limits, and b) slight fluctuations in magnification associated with small changes in the current of the objective lens of the electron microscope. The overall error probably amounted to no more than 5 to 10 pct. In order to obtain readily interpretable data on thickening kinetics, it is essential that the diffusion fields of adjacent ?' plates not be allowed to overlap. Calculations'-' showed that this condition is definitely not ful-

Jan 1, 1969

By M. R. J. Wyllie

The relationship between the electromotive force (E.M.F.) across a shale barrier and the concentrations of sodium chloride solutions on either side has been investigated. It is shown that the action of a shale barrier is analogous to a glass membrane separating two acid solutions of different hydrogen ion concentrations. The shale behaves as a sodium electrode and is responsive to the activities of the sodium ions in the two solutions in such a way that the potential can be calculated by means of the Nernst equation. This conclusion is confirmed by laboratory experiments. In a borehole the total E.M.F. of a shale cell is the algebraic sum of the ~otential across the shale and a boundary potential. The relationship between total E.M.F. and the resistivity ratio of two sodium chloride solutions is indicated for a number of formation temperatures. The E.M.F. thus predicted is then compared with the .elf potential read from an electric log and good agreement is demonstrated. Based on both the self potential and resistivity curves of the electrical log. a method is given for calculating connate water content in a bed having in-tergranular porosity and containing both connate water and hydrocarbons. INTRODUCTION The first paper on electrical well logging by C. and M. Schlumberger and E. G. Leonardon in 1934' attributed the self potential curve principally to streaming potentials, i.e. to electroki-netic effects. Almost immediately great difficulties were encountered in reconciling many of the curves they obtained with this interpretation. and a ~econd paper' by the same authors soon appeared. In this second paper self potentials were attributed to the combined effects of streaming potentials and electrochemical potentials, the electrochemical potential being considered the result mainly of the interaction of fluids of differing salt concentrations, i.e. a boundary potential, and partly of potentials set up at the faces of impermeable materials. Some experiments involving a gray clay for the impermeable material were quated. The Schlumbergers and Leonardon deduced from the equation for a simple boundary ~otential that the electrochemical potential, as opposed to the electrokinetic potential, could be expressed in the form E=Klog- .......1 pe where K is a constant, pm the mud resistivity. p, the resistivity of the connate water in a porous bed. However, no general expression for the constant K was obtained. Although the literature between 1934 and 1943 contains a number of quotations of their results, the valuable work of the Schlumbergers and Leonardon was not extended so that the electrochemical potential has been generally attributed wholly to boundary potentials between the mud in the borehole and the connate waters in porous formations. Unfortunately, however, the fundamental premise of all these papers, that a boundary potential can give rise to current flow in a borehole, is thermodynamically untenable. As will be shown. the fact that the electrochemical potential can be fairly accurately express as E = K log pm/pc, a form in which a boundary potential may also be written, is partly fortuitous. The boundary potential is indeed an integral part of the expression for the electrochemical potential in a horehole, but in magnitude it represents only about 20% of the total potential. In 1943 an important step in the elucidation of electrochemical potentials was made by Mounce and Rust3 who showed that if a wall of shale separated two compartments which contained saline solutions of different concentrations, and if the two solutions were themselves brought into contact in the pores of a porous inert membrane (such as unglazed porcelain) a current flowed through the shale and saline solutions. The direction of positive current was from the shale into the more dilute solution. The paper of Mounce and Rust, while repeating some of the observations of the Schlumbergers and Leonardon, seems to be the first to show that the shale was the seat of a genuine electrochemical effect capable of causing current flow. In the same paper Mounce and Rust pointed out the similarity between the fundamental conditions of their experiment and the conditions which existed when a bed of shale in the ground was simultaneously in contact with a porous sand containing saline connate water and mud fluid of salinity different from that of the water in the sand. Since it is now generally recognized that the S.P. curve measures ohmic potential changes in the mud fluid in the well bore resulting from changes in current flow, it is apparent that currents having their origin in the electrochemical interaction of mud filtrate and connate waters with shale beds are a very important portion of the total S.P. The work of Mounce and Rusta and others appears to indicate that, in general, the electrochemical portion of a particular kick on a S.P. curve far exceeds any electrokinetic potentials resulting either from streaming potentials or Dorn effects. The Dorn effect, or sedimentation potential. arises when small particles are allowed to fall through certain fluids under the influence of gravity. a difference of potential being observe? between two electrodes placed at different levels in the stream of falling particles. The Dorn effect is unlikely to affect seriously the S.P. curve as now measured. A successful analysis of the electrochemical aspects of the S.P. log should

Jan 1, 1949

By Paul Billingsley, Augustus Locke

The mining districts of the first order' of the western United States (and borders) are those named on Fig. 1. These fall into four groups: (1) in the eastern outliers of the Rocky Mountain system; (2) in the Rocky Mountain system itself; (3) in the Great Basin; and (4) in the Sierras and Coast ranges. Of these four groups, the first three are almost entirely of Tertiary age and are within a belt of compressive folding which we shall call the Rocky Mountain-Great Basin thrust arc. The backbone of this belt is shown by the line BAC. The position of the ore districts in this belt indicates a conformance to linear elements of the continental pattern. These are additional to the peripheral elements emphasized by Butler.2 Nature of the Thrust Arc The thrust arc separates regions of contrasted kinds. To the east of it are flat-lying plateaus interrupted by earlier mountain folds; to the west, sunken basins, in which block-faulted ranges lie like an anchored fleet in a sea of desert wash or lava. The. cross-sections are as shown in Fig. 2. The backbone of the belt is the upward and eastward moving block represented by the Glacier Park, the Wasatch, and the Virgin mountains, successively. The structure represented on these sections is the culmination of events which began far back in geologic time and throughout which a contrast has existed between the regions east and west of the backbone line. Before the Pennsylvanian, as Fig. 3 shows, there was a shallow shelf on the east and a deep marine trough on the west; after

Jan 1, 1935

By Paul Billingsley, Augustus Locke

The mining districts of the first order' of the western United States (and borders) are those named on Fig. 1. These fall into four groups: (1) in the eastern outliers of the Rocky Mountain system; (2) in the Rocky Mountain system itself; (3) in the Great Basin; and (4) in the Sierras and Coast ranges. Of these four groups, the first three are almost entirely of Tertiary age and are within a belt of compressive folding which we shall call the Rocky Mountain-Great Basin thrust arc. The backbone of this belt is shown by the line BAC. The position of the ore districts in this belt indicates a conformance to linear elements of the continental pattern. These are additional to the peripheral elements emphasized by Butler.2 Nature of the Thrust Arc The thrust arc separates regions of contrasted kinds. To the east of it are flat-lying plateaus interrupted by earlier mountain folds; to the west, sunken basins, in which block-faulted ranges lie like an anchored fleet in a sea of desert wash or lava. The. cross-sections are as shown in Fig. 2. The backbone of the belt is the upward and eastward moving block represented by the Glacier Park, the Wasatch, and the Virgin mountains, successively. The structure represented on these sections is the culmination of events which began far back in geologic time and throughout which a contrast has existed between the regions east and west of the backbone line. Before the Pennsylvanian, as Fig. 3 shows, there was a shallow shelf on the east and a deep marine trough on the west; after

Jan 1, 1935

The mining districts of the first order' of the western United States (and borders) are those named on Fig. 1. These fall into four groups: (1) in the eastern outliers of the Rocky Mountain system; (2) in the Rocky Mountain system itself; (3) in the Great Basin; and (4) in the Sierras and Coast ranges. Of these four groups, the first three are almost entirely of Tertiary age and are within a belt of compressive folding which we shall call the Rocky Mountain-Great Basin thrust arc. The backbone of this belt is shown by the line BAC. The position of the ore districts in this belt indicates a conformance to linear elements of the continental pattern. These are additional to the peripheral elements emphasized by Butler.2 Nature of the Thrust Arc The thrust arc separates regions of contrasted kinds. To the east of it are flat-lying plateaus interrupted by earlier mountain folds; to the west, sunken basins, in which block-faulted ranges lie like an anchored fleet in a sea of desert wash or lava. The. cross-sections are as shown in Fig. 2. The backbone of the belt is the upward and eastward moving block represented by the Glacier Park, the Wasatch, and the Virgin mountains, successively. The structure represented on these sections is the culmination of events which began far back in geologic time and throughout which a contrast has existed between the regions east and west of the backbone line. Before the Pennsylvanian, as Fig. 3 shows, there was a shallow shelf on the east and a deep marine trough on the west; after

Jan 1, 1935

By W. K. Tony Seiler

Further development of mechanical boring machines for hard and abrasive rocks will be effected by the development of more efficient rock cutting tools or the evolution of entirely new rock excavating principles. Presently the cutting tools suitable for extremely hard rocks and successfully and economically used with raise and tunnel boring machines are tungsten carbide insert big hole cutters. This paper explains the design, rock cutting principles, and actual boring operations to illustrate the capabilities and applications of tungsten carbide (TC) insert cutters. While the rate of borehole advance may fall short of the rapid excavating results achieved with soft rock boring machines, the cutter described in this paper may prove to be the most suitable tool in hard rock excavation for many years to come. DEFINITION OF HARD ROCK Existing bored excavations in hard abrasive rocks are proof of the economic application of new methods and mechanical rock boring in the mining industry. Most of the experience in cutting hard to extremely hard rocks has been gained in raise boring where relatively short and small diameter openings are bored. This poses a lesser risk regarding cutter cost than a long and large diameter tunnel and has therefore promoted the testing of various cutter products. Many types of rocks and geologic conditions were en- countered and actual test data was recorded in materials of up to 100,000 psi uniaxial compressive strength. To clarify the term hard to extremely hard, a 1970 interpretation of rock strength which was recently used is adopted and expanded in this paper.

Jan 1, 1971

By Chi-shing Wang

The late Professor P. B. Bucky of Columbia University introduced the principles and techniques of barodynamic experimentation in early 1931 by the application of centrifugal loading to achieve dynamic similitude between models and prototypes of mine structures.1 Later, he and his associates introduced the combined experimental technique of photo- elasticity and the centrifuge to determine the stress distribution in civil engineering structures and mine workings by the use of transparent bakelite models.2,3 The photostress technique, also known as the birefringent-coating method of photoelastic stress analysis, dates back to 1930, when Mesnager published its principles.4 Since then it has been widely applied to experimental stress analyses in many industries. A practical method of observing the dynamic behavior of opaque mine models, which are made of prototype materials, by means of a combination of the centrifugal and the photostress techniques is a new experimental approach under development at the Henry Krumb School of Mines, Columbia University.5 This paper summarizes the development of the barodynamic photostress technique and presents the information obtained from a recent series of experiments in the study of the behavior of rock beams loaded by their own weight. THEORETICAL BACKGROUND Theory of Pure Bending In the general theory of strength of materials, the flexure stress at any point in a beam of any type of cross section which has a longitudinal

Jan 1, 1968

By P. R. Sheorey

I read this interesting paper on pillar strength in some detail because this is also my area of interest. It has long been the desire of mining rock mechanicians to predict pillar strength from laboratory compression tests. Considerable literature is available on compression strength of rocks and coal but many of these experiments were conducted not for pillar design but for rock behavior. I have a few comments on the author's approach to pillar design, especially equation (33). Two important factors, which the author seems to have excluded, can be added to the right side of equation (2): time-dependence of strength and the influence of mine environment on strength (moisture and weathering.) The author has taken considerable pains to analyze a large amount of testing data in [Table 1], yielding the various exponents ci of equation (2) (or the subsequent equations derived from it.) He has, however, not shown by means of a worked out example how these values of [Table 1] could be applied to a practical pillar design situation. It would have been interesting to compare predicted pillar size using equation (33) with an actual case. Alternatively, equation (33) could have been used to explain the failure of a pillar, if such a case history were available. Consider we have a large number of case histories of stable and collapsed pillars in a seam and we conduct a large number of tests in a laboratory press. The exponents [ci] can then be determined for actual pillars as well as for test specimens. Thus, equation (2) will read [ ] Since laboratory testing conditions (e.g., between steel platens) are different from the conditions on pillars, the exponents [ci] in

Jan 1, 1983