Search Documents

By T. A. Pollard, C. R. Sandberg, E. B. Elfrink

This paper presents an evaluation of compressibility factor data and a discussion of their application to the estimation of gas reserves. A correlation is presented which provides compressibility factors for use in both two-phase and single-phase hydrocarbon systems. Accuracies comparable to those obtained previously for single-phase systems only can be expected. A simple means of predicting the presence or absence of a liquid phase in a condensate system of known composition is illustrated. The correlation is based on 1,030 compressibility determinations from 21 hydrocarbon samples taken from eight oil fields. Of the data used, 75 per cent were from California, 15 per cent were from the Mid-Continent area, and 10 per cent were from South America. The average numerical deviation of the experimental data from this compressibility chart is 1.22 per cent. Charts and tables are included and discussed which illustrate the errors involved through the misuse or nonuse of compressibility factors in estimates of gas-in-place. INTRODUCTION The compressibility factor is a coefficient which expresses the deviation of a gas of given composition from the Perfect Gas Laws. A factor such as this is necessary in any calculation involving volumes of gaseous mixtures, and finds extensive application in the estimation of natural gas and condensate reserves. It is used in the decline curve, the volumetric, and the material balance methods of gas reserves estimation. The behavior of gases at high pressures has been investigated extensively in recent years and considerable data have been assembled on the compressibility characteristics of a number of gases. Notable among the investigators of high pressure gas relationships are Kvalnes and Caddya, Kay" Sage and Laceys, and Brown, Standing" and Katz4. Other contributors are Smith and Watson, Roland and Kaveler', and Stevens and Vance". The data on compressibility factors assembled by these investigators have been presented and correlated in numerous ways; particularly noteworthy is the method first presented by Kay5 which relates compressibility factor "Z" to pseudo-reduced temperature and Pseudo-reduced pressure. Other investigators have used this empirical relationship successfully and numerous charts covering a large number of gases have been constructed on this basis. It is the purpose of this paper to evaluate compressibility factor data and to illustrate the importance of their proper use in the estimation of gas-in-place for both gas and condensate reservoirs. EVALUATION OF COMPRESSIBILITY FACTOR DATA The compressibility chart presented by Standing, Katz, Brown and Holcomb in 1941 is probably the most recent and reliable chart for natural gases. The reliability of the Katz chart has been investigated by the writers for a fairly large number of gases (single-phase) in the pressure range from 500 to 10,000 psia and temperature range from 80 to 400°F. A summary of this comparison is presented in Table I. The numerical average deviation of the chart compressibility factors from the experimental compressibility factors is 1.05 per cent, and the algebraic deviation is -0.28 per cent. The Katz correlation appears to be quite accurate for single-phase hydrocarbon systems. It was based on single-phase systems and does not necessarily provide a means of accurately predicting the behavior of two-phase systems which might be encountered in condensate work. Data published recently by Sage and Oldsl' have enlarged the knowledge of phase behavior in condensate systems by covering extensively the Compressibilities of systems in the two-phase as well as single-phase regions for a wide range of temperatures, pressures and gas-oil ratios. An evaluation of these data indicates that conditions can arise, especially in condensate systems having fairly low gas-oil ratios, in which two phases occur and the usual gaseous compressibility factors do not accurately apply. The measured PVT data of Sage and Olds covering two-phase systems have been correlated with additional such data from the Mid-Continent area and South America; these are presented in Fig. 1. This chart is the result of 1,030 compressibility* determinations from 21 hydrocarbon samples taken from eight oil and condensate fields. Of the data used, 74.75 per cent were from California, 15.45 per cent were from the Mid-Continent area, and 9.80 per cent were from South America. The chart construction is based on the original

Jan 1, 1949

By T&apos Ke, ing-sui

NUMEROUS investigators have observed that internal friction accompanies cold-working of metals and the effect of annealing is to reduce this internal friction.1,2 However, - most of the experiments were made at high stress amplitudes and the principal purpose was to study the increase of internal friction as a result of the applied cyclic stress during measurement. In order to study the internal friction introduced by cold-working applied prior to the measurement, the stress level applied during the measurement of internal friction must be sufficiently small. The results of measurement are significant and can be used for a base of comparison only when the applied cyclic stress is so small that the internal friction is independent of stress amplitude. Internal friction of cold-worked metals under small stress level has been studied by a number of workers8 -" he internal friction was measured around room temperature with a frequency of vibration of the order of kilocycles per second. The purpose of this paper is to report a study of the change of internal friction when severely cold-worked aluminum was annealed at successively higher temperatures until it was completely recrys-tallized. The measurements of internal friction were made over a range of temperature extending from room temperature up to the temperature of prior anneal. The frequency of vibrations used was about one cycle per second. The apparatus used for the internal friction measurements to be reported in this paper was a torsion pendulum with the specimen in wire form as the suspension fiber. The description of this apparatus and the method of measurement have been previously given.7,8 The applied stress was sufficiently small SO that the magnitude of internal friction is independent of stress level at each temperature range concerned. Corresponding to this stress the maximum shearing strain on the surface of the specimen is of the order of l0-5 and lower. The in- ternal friction (Q-1) is reported as 1/p times the logarithmic decrement. Internal Friction Versus Temperature of Anneal: Fig. 1 shows the internal friction measurements performed upon 99.991 pct aluminum subjected to 95 pct reduction in area. The final diameter of the wire is 0.033 in. This figure gives a general survey of the effect of temperature of anneal and of temperature of measurement. The internal friction of the cold-worked specimen was first measured at room temperature. It was then annealed at 50°C for one hour and the internal friction measured at 50°C and at room temperature. The same wire was successively annealed at higher temperatures for one hour and measurements were taken at the annealing temperatures and lower temperatures as before. Such a procedure was followed in order to stabilize the internal friction at the temperature of measurement so that during the measurement which generally takes about half a minute, there is no detectable change in internal friction. This series of measurements .was made up to 450°C. After each annealing a short test piece of the specimen, which had received the same past thermal and mechanical treatments, was taken out for metallographic examination. It is seen from fig. 1 that up to the annealing temperature of 250°C we have the following observations: for any given temperature of measurement, the internal friction is lower the higher the temperature of prior anneal. When the annealing temperature is 290°C or higher, the internal friction at the annealing temperature drops abruptly to a value which is much smaller than that for the previous curve. Metallographic examinations showed that the recrystallization of the specimen was completed after the annealing at 290°C. Fig. 1 shows that, as far as internal friction is concerned, there is no abrupt transition between the processes of recovery and recrystallization. Averbach has also reached the conclusion that recovery may be a process analogous to recrystallization on the basis of X ray extinction measurements in brass." The effect of annealing temperature upon the internal friction at room temperature is shown by curve I of fig. 2. In this figure the internal friction at room temperature was plotted as a function of annealing temperature. It is seen that the internal friction decreases rapidly at first with an increase

Jan 1, 1951

By H. S. Price, J. E. Warren

Techniques for studying the performance characteristics of heterogeneous reservoirs have been developed. The effect of permeability variation on both the steady-state and the transient flow of a single fluid has been investigated. Limited comparisons with field and laboratory data have been made. The physical models studied consist of random three-dimensional arrays of homogeneous porous blocks. The permeabilities of the individual elements are assigned according to a specific distribution function; uniform anisotropy is introduced by varying the relative dimensions of the blocks. A particular model is perturbed simply by re-arranging its elements at random. The behavior of a physical model is determined by digitally solving its numerical analogue. Based on computational experiments, subject to the restrictions implied by the assumptions that were made, the following general conclusions have been drawn. 1. The most probable behavior of a heterogeneous system approaches that of a homogeneous system with a permeability equal to the geometric mean of the individual permeabilities. 2. The effects of flow geometry and anisotropy on the most probable value of the effective permeability of a heterogeneous medium are finite but not significant. 3. The permeability determined from a pressure build-up curve lor a heterogeneous reservoir gives a reasonable value for the effective permeability of the drainage area. 4. A qualitative measure of the degree of heterogeneity and its spatial configuration are obtained from a comparative study of core analysis and pressure build-up data. It has been indicated that these conclusions are predicated on the assumption that the core analysis and the pressure build-up data represent true reservoir characteristics. Common sources of error in these data have been discussed. One of the most significant problems of reservoir engineering is that of determining the nature and the disposition of the heterogeneities that inevitably occur in petroliferous formations. It is with this problem that this paper is concerned. Extensive research, both theoretical and experimental, has provided reasonable descriptions of the physical processes that are associated with primary and secondaryrecovery mechanisms. Similar progress in the fie1d of numerical analysis and the evolution of truly high-speed digital computers have made it feasible to calculate the behavior of these mechanisms under almost any environmental conditions. It appears to be logical, then, to conclude that the mechanistic performance of any reservoir can be predicted with some confidence. Unfortunate1y, a necessary condition for the validity of this conclusion is that the formation be adequately described in a macroscopic sense. This condition cannot be satisfied ill general; therefore, a frustrating situation currently exists — it is possible to compute the effect of reservoir heterogeneity on behavior, but it is not possible to specify the heterogeneity itself. In many cases, the predicted behavior of a project is so completely dominated by irregularities in the formation's physical properties that the gratuitous assumptior, of a particular form for the variation can reduce the solution of the problem to a mere tautological exercise. While all porous media are microscopically heterogeneous, only macroscopic fluctuations need be considered since the fundamental concepts of reservoir mechanics are based on macroscopic quantities. For the simplest case in which only one physical property varies from point to point, the degree of heterogeneity that is apparent depends on three distinct factors, i.e., the nature of the property's variation (frequency distribution), its disposition (spatial distribution) and the inherent stability of the mechanism being studied. Consequently, any attempt to devise an unambiguous scale of heterogeneity must take these factors into account. Since this investigation is intended to be exploratory, it will be restricted to single-phase flow because of the simplification implied; both steady-state and unsteady-state behavior will be considered. Furthermore, to keep the number of parameters

By C. R. Sandberg, T. A. Pollard, E. B. Elfrink

This paper presents an evaluation of compressibility factor data and a discussion of their application to the estimation of gas reserves. A correlation is presented which provides compressibility factors for use in both two-phase and single-phase hydrocarbon systems. Accuracies comparable to those obtained previously for single-phase systems only can be expected. A simple means of predicting the presence or absence of a liquid phase in a condensate system of known composition is illustrated. The correlation is based on 1,030 compressibility determinations from 21 hydrocarbon samples taken from eight oil fields. Of the data used, 75 per cent were from California, 15 per cent were from the Mid-Continent area, and 10 per cent were from South America. The average numerical deviation of the experimental data from this compressibility chart is 1.22 per cent. Charts and tables are included and discussed which illustrate the errors involved through the misuse or nonuse of compressibility factors in estimates of gas-in-place. INTRODUCTION The compressibility factor is a coefficient which expresses the deviation of a gas of given composition from the Perfect Gas Laws. A factor such as this is necessary in any calculation involving volumes of gaseous mixtures, and finds extensive application in the estimation of natural gas and condensate reserves. It is used in the decline curve, the volumetric, and the material balance methods of gas reserves estimation. The behavior of gases at high pressures has been investigated extensively in recent years and considerable data have been assembled on the compressibility characteristics of a number of gases. Notable among the investigators of high pressure gas relationships are Kvalnes and Caddya, Kay" Sage and Laceys, and Brown, Standing" and Katz4. Other contributors are Smith and Watson, Roland and Kaveler', and Stevens and Vance". The data on compressibility factors assembled by these investigators have been presented and correlated in numerous ways; particularly noteworthy is the method first presented by Kay5 which relates compressibility factor "Z" to pseudo-reduced temperature and Pseudo-reduced pressure. Other investigators have used this empirical relationship successfully and numerous charts covering a large number of gases have been constructed on this basis. It is the purpose of this paper to evaluate compressibility factor data and to illustrate the importance of their proper use in the estimation of gas-in-place for both gas and condensate reservoirs. EVALUATION OF COMPRESSIBILITY FACTOR DATA The compressibility chart presented by Standing, Katz, Brown and Holcomb in 1941 is probably the most recent and reliable chart for natural gases. The reliability of the Katz chart has been investigated by the writers for a fairly large number of gases (single-phase) in the pressure range from 500 to 10,000 psia and temperature range from 80 to 400°F. A summary of this comparison is presented in Table I. The numerical average deviation of the chart compressibility factors from the experimental compressibility factors is 1.05 per cent, and the algebraic deviation is -0.28 per cent. The Katz correlation appears to be quite accurate for single-phase hydrocarbon systems. It was based on single-phase systems and does not necessarily provide a means of accurately predicting the behavior of two-phase systems which might be encountered in condensate work. Data published recently by Sage and Oldsl' have enlarged the knowledge of phase behavior in condensate systems by covering extensively the Compressibilities of systems in the two-phase as well as single-phase regions for a wide range of temperatures, pressures and gas-oil ratios. An evaluation of these data indicates that conditions can arise, especially in condensate systems having fairly low gas-oil ratios, in which two phases occur and the usual gaseous compressibility factors do not accurately apply. The measured PVT data of Sage and Olds covering two-phase systems have been correlated with additional such data from the Mid-Continent area and South America; these are presented in Fig. 1. This chart is the result of 1,030 compressibility* determinations from 21 hydrocarbon samples taken from eight oil and condensate fields. Of the data used, 74.75 per cent were from California, 15.45 per cent were from the Mid-Continent area, and 9.80 per cent were from South America. The chart construction is based on the original

Jan 1, 1949

By I. F. Jackson, H. L. Hartman

Hard-metal inserts have received considerable attention in the mining industry recently for a variety of excavating and penetrating purposes. Their use in percussive drilling and in coal cutting machines is well known, but attempts to utilize them in cutting materials such as dimension stone have been discouraging because of excessive tool wear and failure. Particular attention is given to those properties of hard-metal inserts that affect their resistance to wear. A consideration of the actual wear mechanism shows the importance of correct mounting of the inserts and of the selection of suitably powered driving motor so as to achieve minimum tool wear and maximum tool life. Comparisons are made between the performances of types of hard-metal inserts, relating their inherent properties with results obtained in laboratory tests. As part of a broad program to improve the quarrying and processing of industrial minerals, The Pennsylvania State University has been investigating the machinability of slate under laboratory and field conditions. It should be emphasized that the results of the research presented in this paper are also applicable to other natural structural materials, and particularly to the more workable ones such as limestone and sandstone. Improvements which accrue in cutting and sawing should prove of benefit to all the dimension stone industry. Further, it may be pointed out that the results reported here are applicable to rotary drilling (with drag bits) as well as to cutting and sawing of rock. INVESTIGATIONS IN RELATED FIELDS The investigation was initiated with an extensive survey of available literature related to metal cutting and to rotary drilling. The following similar features between metal cutting and slate cutting became evident: 1) Hard-metal inserts are widely used as a cutting tool in both cases. 2) The forces acting on the tool may be resolved into normal and tangential components. 3) Rate of penetration and tool wear are important criteria in each case. On the other hand, important differences also exist: 1) Most metals, exhibit plastic behavior, while slate (and most rock) is a brittle material under normal conditions. 2) In metal cutting the component of force acting parallel to the surface of the workpiece is considerably greater than the force holding the tool against the workpiece. 111 slate cutting, this situation is reversed. Similarities between drag-bit rotary drilling and slate cutting are as follows: 1) In both casts, a tool, usually of the hard-metal insert type, is used to penetrate a brittle material. 2) The drilling forces and related variables, such as rotation speed, are similar. 3) Chip formation in each case is essentially the same. 4) The shape of the tool is similar in rotary drilling and slate cutting. Important differences are also apparent: 1) The objective of drilling is to produce a directed hole, while in cutting it is to form a kerf. In core drilling, however, a kerf is also produced. 2) The horizonta1 component of force in rotary drilling decreases from the center to the outside of the tool, whereas in slate cutting the component is almost uniformly distributed across the width of the tool. 3) The power absorbed in the drill rod is greater in rotary drilling. 4) The clogging action of chips, if excessive power is applied to the tool and if flushing is insufficient, is more serious in rotary drilling. Because of the striking similarities between metal cutting and slate cutting, and between rotary drilling and slate cutting, it was considered that the findings of investigators in those fields would serve as a guide for experimental studies of slate cutting. The following is thus devoted to a discussion of those aspects of metal cutting and rotary drilling pertinent to the present investigations.

Jan 1, 1962

By E. Teghtsoonian, E. M. Schulson

The tensile behavior of bcc ordered P' AuZn single crystals (CsCl structure) has been investigated under varying conditions of temperature, composition, and orientation. Between -0.2 and 0.4 T, multi-stage hardening occurs fm stoichiometric and nonstoichio-metric crystals oriented near the middle of the primary stereographic triangle. At higher and lower temperatures, parabolic type hardening occurs, followed by work - softening at the higher temperatwes. Deviations from stoichiometry give rise to increased flow stresses. Multi-stage hardening was observed for most orientations, except along the [loll-[lll] boundary and near the [001] corner of the stereo -graphic triangle, where parabolic type hardening occurs. Along two slip systems, (hk0)[001] and (, operate simultaneously while in the [001] comer, slip occurs mainly on the system. Electron microscopy of deformed crystals revealed bundles of edge dislocations forming walls approximately Perpendicular to the glide plane. In general the plasticity of 4' AuZn closely resembles the plasticity of bcc crystals. In recent years, considerable interest has arisen concerning the mechanical properties of the CsCl type intermetallic compounds Ag Mg,'- Fe co,' and Ni Al.'-' The compound P'AuZn is structurally similar. It has a low and congruent melting point of 725"~,'" remains ordered up to the melting point,16 and pos-esses a range of solid solubility from 47.5 to 52.0 at. pct Au at room temperature.15 The present paper reports the results of an investigation on the general tensile behavior of material in single crystal form. Some dislocation configurations characteristic of the deformed state are also reported. The results of a detailed study of the slip geometry in AuZn are presented in a separate paper.17 PROCEDURE Alloy preparation, crystal growing techniques, and the procedure followed in selecting specimens of minimum composition variation are reported elsewhere.17 Dumb-bell shaped tensile specimens were prepared by carefully machining single crystals in a jewellers' lathe to a gage length of 0.80 in. and diam of 0.090 in. Back-reflection Laue X-ray patterns and room temperature tensile tests revealed that machining damage could be eliminated by electrochemically polishing 0.005 in. from the machined surface followed by annealing at 300°C for 1 hr. Specimens were polished in fresh 5 pct KCN solution (40°C, 12 v). Experiments were performed by gripping specimens in a self-aligning pin-chuck and threaded collet system, then straining in a floor model Instron tensile machine. All tests were performed in duplicate. Experimental variables included temperature, composition, and orientation. Unless otherwise stated the strain rate was 2.5 x 10"3 per sec. Liquid testing environments included nitrogen (WOK), nitrogen cooled petroleum ether (133" to 293"K), and silicone oil (293" to 488°K). Resolved shear stress-shear strain curves were electronically computed from autographically recorded load-elongation curves. Stress and strain were resolved on the macroscopic noncrystallographic (hkO) [001] system operative under the specific test conditions of temperature, strain rate, and orientation reported earlier.17 RESULTS The temperature dependence of the work-hardening curves is shown in Fig. 1 for gold-rich crystals of 51.0 at. pct Au oriented near the center of the stereo-graphic triangle. Over the range of intermediate temperatures from -200" to 400°K, they are very similar to those classically observed for fcc metals (reviewed by Nabarro et al.).'' The beginning of deformation is characterized by a region of decreasing hardening rate, stage 0, which is followed by a region of low linear hardening, stage I, and then a region of higher linear hardening, stage 11. At the higher temperatures, stage 111 is observed, a region of decreasing hardening rate. Over the intermediate temperature range, the extent of stage 0 and of the slow transition between stages I and I1 decreases with increasing temperature. Total ductility is large, often greater than 300 pct shear. As the temperature is either increased or decreased, the extent of stage I is decreased, giving rise to parabolic type flow and reduced ductility. Similar temperature effects have been reported for bcc ~r~stals.~~-~~ Below -14O°K, hardening is terminated in brittle fracture while above -400°K. initial hardening is followed first by work-softening and then by chisel-edge type ductile fracture. Stoichiometric (50.0 at. pct Au) and Zn-rich (51.0 at. pct Zn) crystals were also tested from 77" to -500°K. The effect of composition on the flow behavior is illus-

Jan 1, 1970

[ ]

Jan 1, 1938

By P. H. Dudley

IN giving a brief account of the experiments in progress to inquire into some of the facts in regard to "railway resistances," recently commenced upon the Lake Shore and Michigan Southern Railway, with the dynagraph (which is essentially an instrument recording upon paper the force required to draw a train, at all speeds, marking the time in short intervals, so that the force absorbed due to any

Jan 1, 1876

By L. R. Shoenberger

Boron has been used to produce nonaging low-carbon sheet steel. Retention of the necessary minimum amount of about 0.006 pet partially killed the steel. Amounts exceeding about 0.012 pet increased the degree of deoxidotion, piping tendencies, and possibility of hot tearing in primary rolling. Semikilled practice resulted in good ingot yields and satisfactory surface quality. Aluminum added with the boron provided a protective de-oxidizer. Good drawobility was indicated by performances of the steel in a limited number of deep-drawing trials. Some problems with hot-tearing and boron-analysis procedures were overcome. Metal lographically, the boron semikilled steels revealed some structures not usually found in plain low-carbon steels. IN 1943 Low and Gensamer1 reported that strain aging, which hardens and embrittles ordinary low-carbon rimmed steel, was due to nitrogen and carbon, and that oxygen played a relatively unimportant role. Since then, many investigators have substantiated their findings and indicated that nitrogen is particularly potent. Commercially, today's most widely produced non-aging sheet steels for deep drawing are either aluminum killed or vanadium rimmed types. The difference in deoxidation practice, alone, is evidence that oxygen is apparently not an important consideration in control of strain aging. The fact that nitrogen is important is apparent in the consideration that has been given, knowingly or unknowingly, to the amount combined with aluminum and vanadium. Patents were granted to Hayes and Griffis2 for the processing of aluminum-killed steel, and to Epstein" for the manufacture of vanadium rimmed material. Certain prescribed steps in producing these steels can be correlated with the formation of the respective nitrides within certain temperature ranges below the usual hot-finishing temperatures. The potential nonaging properties of either type can be reduced or suppressed by cooling too rapidly to permit the aluminum or vanadium to combine with nitrogen. Subsequent suberitical annealing of the cold-rolled strip, however, normally forms the nitrides and produces the resistance to strain aging. Titanium-killed nonaging steel, described by Comstock,1 forms a nitride in the molten state and is essentially nonaging throughout its processing. Zirconium-killed steel, which was investigated briefly by the author,* appeared to have similar nitride- forming characteristics. It is known" that chromium can produce nonaging rimmed steel, but relatively little is known of the potentialities of some of the other nitride-forming elements such as boron, silicon, columbium, and cerium. In attempting to develop a new nonaging cold-rolled sheet steel with good drawability, the following factors were considered pertinent. Such a steel would necessarily have a low carbon content and therefore have a relatively high degree of oxidation when made in a basic open-hearth furnace. If the denitriding element were also a deoxidizer, a part of the addition would be lost as oxide. The degree of deoxidation would determine whether the steel is rimmed, semikilled or killed, and also could be expected to have an important bearing on ingot yields and ultimate surface quality. Assuming that the pattern for the production of cold-rolled sheets would not be changed to any great extent, the nitride must form in the molten steel, in hot rolling, in subsequent cooling, or in annealing. The nitride, once formed, should resist dissociation and be stable in the final product. Usually an excess of the nitride-forming element is required to combine with sufficient nitrogen. If the element used is a strong ferrite strengthener, a small excess may markedly decrease drawability. With aluminum and vanadium, about 0.03 to 0.05 pct in the steel is preferred. Epstein has said" that about 0.30 pct chromium is required. Titanium nonaging steels are hard unless a sufficient amount (about 0.30 pct) is added also to combine with the carbon. The cost of the necessary amounts of these latter two elements discourages commercial acceptance. Silicon was considered as a possible nitride former, but since amounts up to 0.10 pct in rimmed and semikilled steels do not induce marked resistance to strain aging, larger amounts are apparently required, which would tend to harden and strengthen the ferrite. Of the other elements mentioned, all but boron are expensive heavy-metal elements. Stoichi-ometrically, almost an equal weight of boron would be required to combine with the nitrogen—-ordinarily about 0.003 to 0.006 pct in scrap-practice open-hearth steels. Boron is a slightly stronger deoxidizer than carbon but is less powerful than zirconium, aluminum, or titanium. Thus a rimmed-steel practice might be possible. There is much in the technical literature concerning the hardenability effects of minute amounts of boron in killed steels but very little about its behavior in low-carbon material—particularly as a ferrite strengthener. The available data indicated a need for better information concerning the effects of boron in low-carbon strip steels. Experimental Work Development of a Boron-Treated Nonaging Strip Steel—Initial attempts to produce a boron-rimmed strip steel employed 3-ton basic open-hearth heats which could be teemed into molds large enough to sustain a normal rimming action. Boron as ferro-boron was added to the ladle in small amounts because of the reported hot-short character of aluminum-killed heat-treating grades containing more than about 0.005 pct boron. Actually, the amounts used, i.e., 1/8 and 1/4 lb per ton, would be large for

Jan 1, 1959

By T. O. Anderson, E. J. Stahl

Tests to increase knowledge concerning the process of hydraulic fracturing have been performed on three wells in the Allegheny field in western New York. The fracture orientation and its physical appearance at the well-bore was determined by impression packers run at appropriate times throughout the program. Fract~tre azi171uth and its dimensions thus determined were compared to the rock properties and treatment conditions. Logs to provide data concerning rock properties and to improve identification of vertical fractures were run before each step of the fracture treatment. Pressure osc~illu~iot~s were studied after each phase of tile treatments surface pressures during treatment. These measurements show that subsurface pressures exhibit many of the same characteristics as surface pressures during treatment of a well; however, transient pressures are dampened and deelayed in time at the bottom of the well when COmpared with surface pressures. Data obtained from this study provides a means to help locale and determine orientation of vertical fractures made in the open wellbore. Although these rests were performed in only one area, much of the information gained may be applied to fracturing programs in orher areas. INTRODUCTION In this study, various tests were made to provide data to better understand formation fracturing in situ. The reservoir studied is the Richburg oil sand which is a part of a series of predominantly grey sandstones and shales with occasional brown sandstone layers, known as the Caneadea unit of the Canadaway group of Upper Devonian age. Average physical characteristics of 12 cored wells in this area are 13-ft thick gross sand formation, 12-ft thick net sand. 1.7 md permeability, 11 percent porosity, 44 percent oil saturation (before secondary recovery) and 16 percent water saturation (before secondary recovery). This particular area of the Allegheny oil field was originally drilled prior to 1890. The first waterflood secondary recovery attempt was made in 1929. The present sustained waterflood development began in 1951 and is being carried out on a 4.5 to 5-acre spacing. Objectives of these tests were to (I) study fracture azimuth and dimension in relation to rock properties and treating conditions, (2) improve fracture identification techniques, (3) compare surface and subsurface pressure during all phases of treatment and (4) compare the periods of the fluid column oscillations occurring after each phase of treatment. Although the areas of investigation listed appear divergent in purpose, the program was designed primarily to increase knowledge of down-hole conditions leading to rock failure and extension of the fracture thus created. TEST PROCEDURES Wells upon which tests were conducted are designated as Wells 1 through 3. Well 2 was located 440 ft north of Well 1, and Well 3 was located approximately 880 ft west of Well 1. Wells 1 and 2 were completed with cable tools, while the producing interval of Well 3 was rotary cored using fresh water as the drilling fluid to obtain oriented cores. Tests were divided into separate phases on each well as the fracturing program progressed and consisted of measurements performed prior to treatment, during and after the formation breakdown operation. during fracture treatment and after treatment. To verify location and azimuth of the fracture created, and to obtain an impression of wellbore irregularities, a packer was used (Fig. 1). This packer was lowered on tubing into the wellbore opposite the interval under study and inflated in stages to allow the impression material to conform to the wall of the wellbore. A magnetic compass was attached to the tool for orientation reference. Impressions made prior to treatment showed no existing fractures in the wells under study. Impressions made after both formation breakdown and treatment pro-

By W. G. Pfann

In zone-melting, a small molten zone or zones traverse a long charge of alloy or impure metal. Consequences of this manner of freezing are examined with impurerespect to solute distribution in the ingot, with particular reference to purification and to prevention of segregation. Results are expressed in terms of the number, size, and direction of travel of the zones, the initial intermsofsolute distribution, and the distribution coefficient. IF a charge of binary solid-solution alloy is melted and then frozen slowly from one end, as for example in the Bridgman method of making single crystals,' coring usually occurs, with a resulting end-to-end variation in concentration. Such coring, or normal segregation, is undesirable where uniformity is an object. On the other hand, for certain systems, it can be utilized to refine a material by concentrating impurities at one end of the ingot.'. ' In the present paper a different manner of freezing will be examined with respect to the distribution of solute in the ingot. A number of procedures will be indicated which have in common the traversal of a relatively long charge of solid alloy by a small molten zone. Such methods will be denoted by the general term zone-,melting, while the process described in the preceding paragraph will be called normal freezing. It will be shown that, in contrast to normal freezing, zone-melting affords wide latitude in possible distributions of solute. Segregation can either be almost entirely eliminated or it can be enhanced so as to provide a high degree of sttparation of solute and solvent. A number of simplifying assumptions will be invoked which, while not entirely realizable in practice, nevertheless provide a suitable point of departure for more refined treatments. Moreover, our own experience with zone-melting has shown that, for certain systems at least, the analysis holds quite well. The present paper will be confined to a discussion of principles and a general description of procedures. Comparison with experiment is planned for later publication. Normal Freezing Before considering zone-melting, segregation during normal freezing will be reviewed briefly. If a cylinder of molten binary alloy is made to freeze from one end as in Fig. 1, there usually will be a segregating action which will concentrate the solute in one or the other end of the ingot. If the constitutional diagram for the system is like that of Fig. 2, then the distribution coefficient k, defined as the ratio of the concentration in the solid to that in the liquid at equilibrium, will be less than one and the solute will be concentrated in the last regions to freeze. If the solute raises the freezing point, then k will be greater than one and the solute will be concentrated in the first regions to freeze. The concentration in the solid as a function of g, the fraction which has solidified, can be expressed by the relation: C = kC0 (1-g)k-1 [I] where C, is the initial solute concentration in the melt. Eq 1 is based on the following assumptions: 1—Diffusion in the solid is negligible. 2—Diffusion in the liquid is complete (i.e., concentration in the liquid is uniform). 3—k is constant. Concentration curves representing eq 1 for k's from 0.01 to 5.0 are plotted in Fig. 3. This equation, in one form or another, has been treated by Gulliver,³ Scheuer,4 Hayes and Chipman5 for alloys and by McFee2 for NaCl crystals. It is derived in Appendix I. It should be pointed out that the k which is calculated from the phase diagram will be valid only in the ideal case for which the stated assumptions are correct. In all actual cases, the effective k will be larger than this value for solutes which lower the melting point, smaller for solutes which raise the melting point, and will probably vary during the beginning of the freezing process. For simplification it will be assumed that the ideal k is valid. Zone-Leveling Processes The processes of this part are designed to produce a uniform, or level, distribution of solute in the ingot. Single Pass: Consider a rod or charge of alloy whose cross-section is constant and whose composition, C2, is constant, although permissibly varying on a microscopic scale." Such a charge might be a rapidly frozen casting or a mixture of crushed or powdered constituents. Cause a molten zone of

Jan 1, 1953

By M. Kaitz

A continuing discussion in both the petroleum engineering and economic literature is directed to the difficulties encountered in the use of discounted cash flow rate of return (DCF) as a measure of investment worth. Although useful in most Instances, DCF has been criticized because it is time-consuming in its trial-and-error solution, theoretically invalid, not adaptable to cash flow streams yielding multiple return solutions and not entirely reliable in selecting between mutually exclusive investments. The theoretical invalidity of DCF stems from the reinvestment assumption implicit in the calculation that earnings are reinvested at the DCF rate. The emerging consensus of the economic literature is that the net present value or the present worth of the net cash flow stream (discounting at the average opportunity or cost of capital rate) is more correct and reliable. Other criteria proposed have been ratios of net present value divided by initial investment or by present value of all investments in a project. All of these criteria are simple to determine and explicitly assume a reinvestment rate for [he income generated by a project. This paper develops and discusses a theoretically valid profitability criterion which is simple to compute and retains the appeal of a percent return on investment. It is called "percentage gain on investment" or PGI. It measures the gain an investment is expected to realize over like capital invested in the average opportunity and explicitly considers reinvestment potential. Why add another Concept to the large array of investment criteria now available, any one of which, or perhaps a combination of several, appears to embrace the form's (or individuals) objectives? The answer is that not one of the existing criteria provides both a readily comprehensible and theoretically valid measure of risk coverage that has general application. The proposed PGI does fulfill these requirements. INTRODUCTION An ancient expression warns that "one must yield to the times" — there are better ways of doing things. A review of the petroleum engineering and economic literature on one topic alone, measurement of investment worth, certainly is witness to this truth. In use for a number of years, the DCF has recently received attention, directed mainly to its theoretical invalidity. Several alternatives to DCF have been proposed to provide a valid, simply determined criterion to describe investment worth and to overcome the criticisms previously mentioned. This paper introduces another method called percentage gain on investment (PGI) and is proposed as but one of several yardsticks that should be used in making investment decisions. MEASURES OF INVESTMENT WORTH This paper will consider only those criteria which give weight to the time pattern of future earnings. These criteria are usually compared with an average opportunity rate or cost of capital of the firm to judge the relative worth of the investment. For purposes of demonstration, a 9 percent average opportunity rate will be used throughout this paper. Implicit in the DCF calculation is the assumption that earnings are reinvested at the DCF rate. Some argue, though, that there is no reinvestment assumption,' that the DCF rate is simply that maximum rate of interest one can pay on the investment over the life of the project and break even. The determination of DCF is accomplished by discounting the net cash flow stream at that rate (DCF) which will yield zero. The question is: why should reinvestment potential be explicitly considered in calculating return on investment or other criteria measuring economic worth? Perhaps the answer lies in consistent or equal treatment of future cash flow. It appears entirely illogical to give different present worth value to $1 received, say, 10 years from now, which is the circumstance resulting in comparing projects with different DCF returns. In fact, $1 received in 10 years has the same value regardless of which project generated the income. DCF return thus favors investment projects which are expected to provide early income as compared to those providing long-term income. Not surprisingly, the controversy on reinvestment assumption is an old one. Hoskold' discussed this same problem in 1877. He considered the future income from mineral properties as an annuity or a series of fixed future payments. (As will be demonstrated, his equation can be modified for variable income.) Prior to Hoskold, the value or what one could pay for the mine, was determined with the use of standard, single-interest tables. Here is what Hoskold said with regard to these tables. "This table, and others of its kind, to be found in most works on annuities, is constructed correctly according to

By N. J. Grant, E. Gregory

The creep rupture properties of wrought aluminum powder products made from five grades of sintered aluminum powder were investigated at temperatures from 400° to 900°F for rupture times up to 1000 hr. The effect of stress concentrations on materials of this type was investigated by means of notched creep rupture tests. A tentative correlation was obtained between the creep rupture properties and the structure as revealed by electron micrographs. SEVERAL papers have been published recently concerning the production and properties of wrought aluminum powder products and their possible high temperature applications. Most of the published work in this field has come from abroad, notably Switzerland, and articles by Irmann and his colleagues were summarized in English recently.'.' Most of the papers published by Dr. Irmann are principally concerned with the retention of properties (by a product which is produced from extremely fine flake powder and is subsequently hot extruded) after heating to high temperature for prolonged times. The powder may be in atomized or flake form, and during hot working the applied pressure is reported to plastically deform the aluminum powder, thus breaking the oxide skin and welding the particles together. Irmann attributes the remarkable properties to the dispersion of oxide inclusions. Specifically, the product described by Irmann is one labeled SAP (Sintered Aluminum Powder) in which the initial flake powder is so fine that at least 50 pct of the flakes have one dimension of 2 microns or less. The composition of the starting aluminum shows in percent, Fe, 0.18; Si, 0.19; Zn, 0.06; Ti, 0.03; Cu, Mn, Mg, all nil; balance Al, approximately 99.5 pct. Aluminum is not the only material that has been found to have increased resistance to deformation at elevated temperatures when produced by powder metallurgy. It has been reported by Middleton, Pf eil, and Rhodes- hat platinum has a higher recrys-tallization temperature when produced by powder metallurgy and exhibits peculiar properties, many of which are similar to those of the aluminum powder products. Difficulties were encountered in explaining the reason for the strengthening in the case of platinum since the existence of the oxide is doubtful. The authors attributed the special properties to "a small amount of suitably dispersed porosity." This theory was supported by von -~eer-leder4 in the discussion to the paper, and the similarity between this method of hardening and that suggested by Rohner in his theory of age hardening was pointed out. R. de Fleury5 attempted to explain some of the properties in terms of the modulus of elasticity and elastic limit of alumina and aluminum while von Zeerleder examined the relationship between the yield strength and the reciprocal of the powder particle size. Boenisch and WiderholtQ dealt mainly with the corrosion resistance of the powder aluminum material and compared it with other aluminum alloys. The diffusion rates of other metals in SAP and pure aluminum have been compared by Seith and Lop-mann.' They showed that the alloying metals diffuse particularly quickly in SAP possibly due to the very fine grain size. The properties of the Alcoa products were given by Lyle.' The creep rupture properties of SAP and two of the Alcoa experimental powder products were compared by Gregory and Grant hnd it was shown that these products are vastly stronger at 900°F than are the best cast and wrought alloys at 600°F. Since the publication of these data, the authors have investigated two further aluminum powder products and it is the object of this paper to show how the high temperature creep rupture properties of the five materials vary with oxide content and with the structure as revealed by electron microscopy. Materials One of the five products, SAP, a sintered aluminum product, was supplied by the Societe Anonyme pourl Industrie de l,Aluminium, Neuhausen a/RHF, Switzerland, through Dr. R. Irmann, while the others, M276, M257, M293, and M255 were supplied by the Aluminum Company of America as experimental powder metallurgical products. M255- and M293 were made from coarse and fine atomized powders, respectively. The other materials were made from flake powders with significant differences in oxide content, the details of the type of powders used in the manufacture of these materials

Jan 1, 1955

By Paul Foote

The temperature of a material may be ascertained by measurement of the intensity of the radiant energy it emits. This measurement may refer to the radiation of all wave lengths emitted by the material, or, if the material is glowing, the measurement may refer to the visible light emitted, or to the radiation in n very restricted portion of the visible spectrum. In general, the intensity of radiation depends not alone upon the temperature of the source, but, also upon its nature. Thus, glowing carbon appears to the eye about three times as bright as glowing platinum, at the same temperature. This is technically expressed by saying that the emissive power or emissivity of carbon is about three times that of platinum. A material having the highest theoretically possible emissivity is known as a "black body;" it is customary to assign a numerical value of 1 to the emissivity of a black body. A black body is experimentally realized by uniformly heating a hollow enclosure and observing the radiation coming from a small opening in the wall. The intensity of radiation emitted from this opening depends only on the temperature of the walls, and not on the material of which they are constructed. If E is the emissivity of any non-transparent material and R is its reflection coefficient, it can be shown that E + R, = 1. If a material having an emissivity of, say, 0.40, and hence a reflection coefficient of 0.60, is placed inside a black body it becomes indistinguishable from its Surroundings, because the total intensity of radiation leaving the material is the same as that emitted by the black body. While the material actually emits only 40 per cent of the intensity of a black body at the same temperature, 60 per cent. of the radiation falling upon it from the walls of the enclosure is reflected. However, if the material is removed from the black body and placed in the open air, the reflected intensity is no longer present and the object appears but 40 per cent. as bright as a black body at the same temperature.

Jan 8, 1919

By F. H. Newell

At the Glen Summit meeting of the Institute, held in October, 1891, the writer presented a paper on the results of stream-measurements of the United States Geological Survey, reviewing briefly the data obtained at that time.* Since then the investigations have been steadily continued and enlarged, so that at the present time about 150 river-stations are main-

Jan 1, 1898

Jan 1, 1965

By Stefan S. Kapusniak, Nichol Riggott, Stephen F. Smith

Stability investigations have been carried out in a number of major coal mining tunnels in the U.K. using various instrumentatcon techniques. The paper describes these instrumentation methods and presents results from studies in several tunnels. Both long and short term stability aspects are discussed. Prediction of tunnel stability is examined in relation to tunnel support requirements. Computer simulation techniques are used along with actual underground measurements to identify tunnel design parameters for influencing choice of support and prediction of long term stability.

Jan 1, 1984

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

Dispersion-containing titanium-copper alloys were prepared having mean free paths varying from 1.0 to 9.7 P. Tensile studies at room temperature and at 1000°F showed that little or no strengthening occurred when the mean free path exceeded 3 p. However, at lower values of mean free path appreczable strengthening was observed. A considerable amount of strengthening also resulted from copper in solid solution. DURING the past several years, an increasing amount of study has been devoted to dispersion hardening, an alloying process in which increased strength is obtained through the addition of a ran-

Jan 1, 1961

By R. D. Mollison

"For his contributions to mining which are highlighted by perseverance; successful exploration, particularly the Kidd Creek deposit; technological advancement and sound management policies; and for his lecture, "Exploration-The Diversificiation and Development of a Mining Company." Recipient of the 1983 D.C. Jackling Award

Jan 1, 1984

By H. B. Emerick

An effort has been made to evaluate the individual influence of various factors in steel making and rolling operations upon the surface quality of semi-finished steel products. The thoughts expressed are not entirely theoretical, but rather are based upon several years critical observation of mill yields and rejec-tions and are supported by actual data wherever this has been possible.

Jan 1, 1940