Search Documents

By A. E. Harnsberger

IT is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practically every refinery operation, from the charging of crude oil to a distillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from -50° F. to 900° F. Pressure may vary from subatmospheric to 2000 lb. per sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four, most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature may be divided into three parts: (1) extremely low temperatures of the order of -50° F.; (2) temperatures at atmospheric or slightly above; .(3) temperatures from 200° to 900° F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of. 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250° F. The second type of corrosion occurs in high-temperature pumping equipment, with temperatures from 450° to 900° F., largely caused by sulfur compounds. There are also other corrosive conditions met with

Jan 1, 1935

By V. F. Hollister, M. Bernstein

The Copaquire porphyry copper deposit lies in an island of pre-Upper Tertiary rocks surrounded by Quaternary and Upper Tertiary formations. The pre-Upper Tertiary appears to be a horst block in a typical basin-range setting. Major right lateral faults have been mapped within the range from Chuquicamata north to Copaquire. All of the major porphyry copper deposits known in the block (e.g., Quebrada Blanca, El Abra, Chuquicamata, and Copaquire) are on or are very close to one of these major right lateral shears. In the Copaquire district, an epizonal igneous complex with diorite, quartz diorite, quartz monzonite, and intrusive dacite (in that intrusive order) invade folded Jurassic shale. Mineralization appears spatially and temporally associated with the quartz monzonite porphyry and dacite. Alteration zoning shows two separate core phyllic (quartz-sericite-pyrite) zones within one large argillic (clay-pyrite) zone. A propylitic (chlorite) zone is peripheral to the argillic zone. No potassic zone has been recognized yet at the surface. The intrusive petrology together with the phyllic, argilic, and propylitic alteration zoning as well as the chalcopyrite-molybdenite ore mineralogy characterize this deposit as being typical of the Lowell and Guilbert model. Copper and molybdenum minerals appear to be most strongly developed in the phyllic zone, in either a breccia or a zone of veinlets and stockwork which trend dominantly northeast, conjugate to the district's largest fault, the Sulfato fault. The setting is basically similar to that found in some other porphyry copper deposits in this block, in that the ore body is a zone of veinlets which appear to be genetically related to movement on a major north-south trending right lateral fault. The presence of the major fault in each deposit, and the speculative hypothesis that paleo-subduction zone operated at the time of mineralization, suggest the possibility that mineralization took place when a major fault permitted escape to the surface of cal-calkalic magma generated in a subduction zone as proposed by Ericksen. A hypothesis such as that proposed by Ericksen explains the near linearity of porphyry copper deposits in Chile, since the source of calc-alkalic magma would exist at about the same distance from a paleo-trench throughout the length of the paleo-subduction zone.

Jan 1, 1976

By N. T. Burdine

Formulas for calculating relative permeability from pore size distribution data are derived from basic laws of fluid flow ill porous media. The tortuosity factors that appear in the equation5 are described in. terms of the physical properties of tile medium and the saturations of the contained fluids. Procedures for calculating and methods for measuring the tortuosity factors are discussed. Values of relative permeability calculated by the formulas art: compared with results obtained by experimental measurements I INTRODUCTION Recently, several investigators have derived relative permeability equations from Darey's and Poisenille's Laws in which some, physical factor or factors describing the porous system appear. The factor that has caused the greatest amount of comment, and which is probably least understood, is the tortuosity of the fluid {lath ill the porous sample. Values of the tortuosity factors appearing in the equations range from a constant for all condition- of the fluid flow system to an inverse function of the pore radii. It is the purpose of this paper to compare wine experi~i~cntslly determined relative permeability curves with those calculated by a method which utilized capillary pressure infortmation. The capillary pressure data were obtained prefer.. ably from pore size distribution information as determined by mercury injection but. in some cases, in the absence of suitable mercury injection information. data were taken from measurements made by the porous semi-permeable diaphragm method. The physical significance of certain tortuosity concepts is inferred and the determinations of the tortuosity factors from pore size distribution data and by electrical measurements are discussed. THEORETICAL BACKGROUND In previously reported studies on pore size distribution in petroleum reservoir rocks. by the author and co-workers ail equation was derived relating specific permeability. k, to pore entry radii, R, porosity. . tortuosity factor. .,, and incremental pore volume. V. The equation is where being the "effective" length of the flow path in the porous sample. and L the length of the porous sample., The constant. 0.126. is a units conversion factor. (This definition of tortuosity factor X, = L L does not conform to all such definitions found in the literature. Fly similarity, in a two-phase system. the effective permeability of the wetting-phase.

Jan 1, 1953

By Park Wright

THE fact that granite has been encountered by the drill by those in search of oil and gas in Kansas is becoming more and more a matter of interest, not only to the oil producer but to everyone directly and- indirectly connected with the oil business. It is, therefore, time that someone should offer an explanation for its presence and form a definite opinion based on all the data available in regard to the effect it will have on the future prospects of the area affected as probable oil- and gas-producing territory. At present there seems to be no consensus of opinion. To the writer's knowledge, only one attempt has been made to explain; by Erasmus Haworth, State Geologist of Kansas, in a paper entitled Bulletin, Number Two on Crystalline Rocks in Kansas. The purpose of the present paper is to offer a theory for the presence of the granite and to draw conclusions which will aid in determining the prospective oil and gas value of the area in question. In taking up this question it will be well to consider first the tests in which granite has been reported, with a general history of each. The accompanying map (Fig. 1) shows the location of all wells described. The first well in which granite was reported was that drilled just south of Zeandale in section 27, township 10 south, range 9 east, by a local company which had taken up a block of leases in that vicinity. At a depth of 958 ft. (291.99 m.) granite was encountered. Drilling was continued to a depth of 1,093 ft. (333 m.) in the same formation, at which depth the hole was abandoned. Another well was started 1 mile east of the first well and the same rock was found at a depth of 945 ft. (288 m.). Drilling was continued to a depth of 1,200 ft. (365.76 m.) with the bit in the sane formation. Samples of the drill cuttings have been examined and they are undoubtedly crushed granite. The next well in which granite was found was that drilled by DeLaat and Shepard, independent wildcat operators, in section 34, township 19 south,. range 7 east, near the town of Elmdale. Granite was struck at 1,707 ft. (520 m.) and the hole was abandoned in the same formation at 2,525 ft. (769 m.). Mr. DeLaat watched the drilling of this well very closely and he has described to me in some detail the formation immedi-

Jan 8, 1917

By Douglas Muir, Chas. A. Chase

The Aztec mine is not widely known, by reason of its isolation and the relative insignificance of its tonnage; financially, however, it has an enviable record and geologically it is extremely interesting. The town of Baldy, Colfax County, the mine camp, at an elevation of 10,000 ft. (3048 m.) is 8 mi. west of Ute Park, the terminus of a branch of the A. T. & S. I?. Ry. The mining tract was designated by the Maxwell Land Grant Co. as the Aztec Reservation, and lies on the east slope of Mt. Baldy, the summit of which, 12,491 ft. (3807 m.), is one of the highest in the state. Rich copper float was found on the northeast slope of the mountain in 1865, and discovery work was begun the next year. At the same time, gold placers were found on Willow Creek, on the southwest side of the mountain, and the Elizabethtown settlement followed shortly. Gold washing lasted many years. In 1867, placer gold was found also on Ute Creek, the tracing of which to its source led to the locating of the Aztec mine by Lynch, Dogherty, and Fosley in the following year. The early production came from the contact of shale and sandstone or from sandstone immediately above the contact. Exact record of production is lacking, but L. C. Gratonl gives estimates ranging between $1,250,000 and $1,500,000, of which about $1,000,000 was taken out in the first four years. After the exhaustion of the early bonanza, production continued intermittently until 1909, when the Maxwell Land Grant Co, undertook systematic development, through four adits at intervals of 75 ft. vertically or approximately 100 ft. on the dip of the contact, which was thought to contain generally a quartz-pyrite vein. The two intermediate adit? almost immediately reached ore, the most southeasterly in Fig. 2. This ore, however, was not mined until 1911-12; its grade was about $20 and

Jan 1, 1923

By Ralph Wilcox

THE diamond drilling of certain characters of unstable rock forma-tion, as, for example, the copper-bearing schists of the Miami district in Arizona, is rendered most difficult by what is known as " caving" of the sides of the drill holes. As this caving is very greatly increased by the action of flowing water, it occurred to me, after experiencing a great deal of difficulty with caving in diamond-drill holes which I was drilling for the Miami Copper Co., that if I could substitute air for water, much of the caving-with resultant difficulties, such as decreased speed of sinking and increased consumption. of diamonds-would be overcome. After some experimenting, I found that it was perfectly practicable to substitute air for the water; forcing the air down the hollow rotating rods in the same manner as is done with water, the air passing out around the bit, which is thus cooled, and ascending on the outside of the rods to the collar of the hole, carrying the borings in just as satisfactory a manner as had been done by the water, but without the accompanying destruction or caving of the sides of the drill holes such as had been so generally experienced with the water. When water was encountered in the drilling this water was forced up to the collar just as it would have been had water been used in the .drilling, but with the correspondingly decreased flow there was relatively less washing or caving of the sides of the drill holes. The only change necessary in the arrangement of the drill is that a cross instead of a tee is used at the collar of the hole. A tightly woven jute bag is attached to one arm of the cross, for collecting and filtering the sample; and when drilling in dry ground a jet of water is attached to the opposite arm of the cross, to collect the dust and wash down the sample into the bag. The rods rotate through a stuffing box attached to the upper opening of the cross. The distention of the jute bag by the issuing air indicates the operating conditions as sufficiently as did the flow of water when using water in the drill hole.

Jan 10, 1913

By Marshall D. Himes

The Pima mine, Pima County, Ariz., a 53,500-tpd copper mine, is located 17 miles south of Tucson, Ariz. The mine is in a sequence of Paleozoic and Mesozoic sediments striking east-north-east and dipping southeasterly. These sediments are intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian (?) dolomites, limestones, and sandstones have been altered to calc-silicate skarn, marble, and quartzite. The overlying Mesozoic Triassic (?) clastic sediments have undergone some recrystallization and hydrothermal alteration. The clastic metasediments are divided into three distinct lithologic units: lithic arenite, arkose, and interbedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite, and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar, quartz, and sericite, with or without chlorite and calcite). The porphyry has undergone potassic alteration. Dominant structures are an east-west postmineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. The two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast, and the other striking northeast, dipping northwest. Economic mineralization is prediminantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are less important amounts of magnetite, hematite, sphalerite, galena, tennantite, and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1974

By E. T. Dumble

In continuation of the geological work begun in Sonora, Mexico, a partial account of which has already been given in the Transactions of the Institute,* a similar reconnaissance was made of Cochise county, Arizona, and a part of the Whetstone mountains. The investigation resulted in the identification of beds of similar age and character to those of the Sonora region, and in the discovery of interesting deposits, which, so far as I call ascertain from the literature at my command, have not been described heretofore. Route.—Starting from Nogales, we followed the railroad to Crittenden, and then drove to the southeastern slope of the Whetstones. After a brief examination of some reported coalbeds we continued our route, following the wagon-road between the Whetstones and the Mustang mountains to Huachuca, and eastward to Tombstone. Crossing the Dragoon mountains at South Pass, we traveled south and west by way of Turquoise and Antelope Spring into the road from Tombstone to Bisbee. Our route over the Mule mountains lay through Mule Pass and Bisbee, where we stopped a day or two. Thence, crossing Sulphur Spring valley, we drove around the southern end of the Swisshelms, and N. through the valley between these mountains and the Chiricahuas, to White river. From that point our way led through Rucker canon into the San Simon valley, then northward along the eastern face of the Chiricahuas, and by way of Fort Bowie to Willcox, Arizona, from which place we returned to Nogales. It was greatly regretted that the extremely wet weather prevented us from including in our examination the Huachuca

Jan 1, 1902

By W. F. Brace, James D. Byerlee

Although prediction of failure of rocks may be ultimately possible without knowing in detail how failure occurs, understanding of this process is certainly of fundamental interest in rock mechanics. Of the various failure mechanisms, probably brittle fracture is of greatest interest. Recent reviews have brought this subject nearly up to date (Hock,1 Price,2 and Jaeger 3) and here, we summarize certain recent developments. As our understanding of brittle fracture is derived almost solely from laboratory studies this will amount to a review of certain laboratory experiments. New studies in four areas are pertinent; these concern 1) the volume changes which accompany brittle fracture, 2) the propagation of cracks in compression, 3) certain frictional characteristics of rocks and minerals at high pressure, and 4) the law of effective stress for crystalline rocks. Our objective here is less to present an entirely consistent, complete picture of how a rock fractures than it is to emphasize gaps in our understanding and, thus, suggest areas that need further study. Progress is still painfully slow in this field and perhaps this approach will stimulate new work. OBSERVATIONS Although the behavior of large rock masses is most often the concern in rock mechanics, the number of large-scale experimental tests is still vanishingly small. Our experimental observations arc, by and large, still made on small, relatively flaw-free, rock samples. Here also we report the behavior of small samples.

Jan 1, 1967

By Frederic P. Dewey

It is common to blame irregular assay results upon volatilization and much has been written upon the subject, but there is no real evidence that, in a properly conducted assay, the loss of either gold or silver by volatilization is sufficient to affect appreciably the result, even when arsenic or antimony may be present. Bulk assays of flue dust from assay muffles have been published, but the data given are totally insufficient to even approximate the volatilization from a single assay; and such figures as we have indicate the volatilization to be extremely small. Diligent search in the literature and wide inquiry among assayers and instructors have failed to produce a single case where the litharge volatilized in making an assay has been collected and assayed for gold and silver. Having attempted to do this, with most indifferent success, I am not surprised that this has not been done. While various textbooks give volatilization as a cause of loss in cupella-tion, it may safely be said that in the rare cases where this volatilization is sufficient to affect appreciably the result it is due to excessive temperature. Percy' says "The loss of silver by volatilization during cupellation is very slight (unless the temperature has been much too high), and may be disregarded." This statement is repeated by the Beringers2 and Smith,3 who includes gold with silver. Mitchell4 says the litharge fume rarely contains over one ten-thousandth of silver. Campredon5 ays that at a proper temperature no silver is lost by volatilization. Primarily, excessive temperature may be due to too high general temperature in the muffle; but it may often be due to temperature localized within the bead by oxidation of the metals and this may be influenced by other causes than the general temperature. I have shown an ex-

Jan 1, 1921

By T. M. Chance

The first bituminous coal cleaning-plant to use the sand-flotation process1 was placed in operation on Oct. 1, 1925, at the tipple of the East Broad Top Railroad & Coal Co., at Mt. Union, Pa. The general principles governing the design of plants of this type and typical operating results of anthracite sand-flotation units have been previously outlined.2 I will, therefore, confine myself to a description of this particular plant and to some of the elements of design it incorporates. The Original Mt. Union Tipple The plant was installed to transfer coal.from steel narrow-gage cars of 60,000 and 70,000 lb. capacity to standard-gage equipment. The coal was hauled about 30 miles from the East Broad Top field. This coa1, mined by the Rockhill Coal & Iron Co. and other operators, is a low-volatile slow-coking coal with ash of high-fusion point. It is normally a high-grade coal that does not contain an excessive amount of free impurities, but it requires careful handling to secure a fair domestic yield, and, naturally, the need for narrow-gage transshipment increases the difficulty of the problem. The narrow-gage cars were discharged into an 8-car track hopper equipped with two feeders passing the coal to two 42-in. apron intake conveyors. Twin units were installed throughout the original plant, two lump-and-egg shaking screens, two lump picking-tables, two egg picking-tables and two stoker conveyors. The stoker coal was loaded without cleaning. The loading tracks and booms were in duplicate and, with the layout as originally installed, either unit could be run independently, each unit shipping a different class of coal or both units making the same product.

Jan 1, 1927

By C. E. Julihn

Technology concerns the ways of doing things; mineral technology the ways of performing operations required for obtaining minerals from the earth and extracting their valuable constituents for man's use. At any particular time, technology is relatively fixed, as everyone tries to adopt the way of doing things that has proved most profitable; but improvements evolve from minor changes here and there, and occasion- ally entirely new methods are discovered. Technologic improvement thus characterizes any long-time view of the mineral industries. Its test lies always in reduction of costs; there is no other incentive for the adoption of new methods. Reduction in cost of producing metal from ore decreases, in turn, the amount of metal that must be obtained from ore in order to pay for its production. An advancing technology thus is characterized by utilization of ores of lower and lower grade. A very important result of this is an increase in the gross quantity of metal obtainable at any price level, since the earth's crust contains vast amounts of very low-grade ores and relatively insignificant amounts of very high-grade ores. Technologic advances have, therefore, been the means of rendering the metals both cheap and abundant. Though concern as to possible exhaustion of the world's ore deposits is warranted, it is conceivable that a transcendent technology of the future might supply metal requirements from what we

Jan 1, 1932

By J. M. Hodge, M. A. Orehoski

tions to which it will be subjected, and this premise is probably the most important reason for hardenability control. However, the criterion of hardenability [ ] ture after quenching should consist wholly of martensite; and that transformation of austenite to intermediate-temperature products during quenching will have a deleterious effect upon the physical properties, particularly the toughness, of the tempered material. This implies that, in order to obtain the optimum physical properties from a given steel, its "hardenability" should be high enough to suppress all transformation except that to martensite under the heating and quenching condi- IT is now generally conceded that if a steel is to develop optimum physical properties in the conventionally quenched and tempered condition, the microstruc- [ ] that at present is most widely accepted and used is based on a microstructure of 50 per cent martensite. This criterion, which was suggested by Grossmann,1 does have considerable justification. It may be readily measured by a fracture or etch test and, since it represents the point at which the hardness is changing most rapidly with variations in cooling rate, it may be determined empirically from a hardness-depth curve by determining the point of steepest slope (the inflection point. Furthermore, in plain carbon steels or in steers of low hardenability, the difference in hardenability expressed in

Jan 1, 1945

By Earl Oliver, J. B. Umpleby

It is believed that in connection with the study of unit operation by the Petroleum Division of the A. I. M. E. a review of the simple principles of unit operation would be helpful. To that end, the following discussion is submitted. It is not to be considered in any sense as the conclusion of the committee, but rather as material submitted for its consideration and represents at this time only the viewpoints of its authors. Growth of the Oil Industry In 70 years the oil industry has grown from a single well on Oil Creek, Venango County, Pennsylvania, producing 25 bbl, per day, to more than 400,000 wells scattered over five continents with a daily output of 4,000,000 bbl. In that time petroleum has expanded from its simple use as a medicine in a few localities to a multitude of diverse uses in homes of every country the world over. During those years the oil fields of the United States have produced two-thirds of the world's output and have shipped their excess production into almost every country. In those years several hundred thousand good wells in the United States declined into small ones and depleted shallow deposits gave way to deep zones; so that the United States crude oil industry gradually changed from one of low cost production to one of higher cost. Throughout its entire life it has labored under two serious economic disadvantages, namely, constantly recurring periods of demoralization through overproduction, and competitive development methods that are wasteful. Development of Foreign Competition During the transition from low to higher cost production in the United States, events even more significant were taking place in foreign lands. Jungles were tamed and deserts conquered. Oil deposits were found and developed until, in the words of Sir John Cadman, "the globe is now drenched with a commodity which, although necessary to life, involves but an irregular and sometimes meager expenditure of life in its

Jan 1, 1930

By Masayuje Otagawa

The mining methods adopted in Japanese mines are less known to the mining world than those of other countries, owing to the geographical remoteness, but they present many features of interest to mining engineers. The Ashio copper mine is at the town of Ashio, in Tochigiken, about 109 mi. (175 km.) from Tokyo by the Imperial Government railroad. The area of the concession owned by the Furukawa Mining Co. is 5000 acres (5023 ha.). The mine was formerly divided into three, viz. Hon-ean, Kotaki, and Tsudo, which are distant 3 mi. (4.8 km.) from each other as shown in Fig. 1. However, in 1914, when the writer was general manager, the three mining plants were amalgamated into one with the result of simplifying the working projects and increasing the operating efficiency. The mine was visited by the Institute party in November, 1911, when K. Inouye was the general manager. Shortly afterward, the writer was appointed manager, and, in 1915, he was succeeded by Dr. K. Asano. At the end of 1917, K. Kibe became general manager and, after two years, was succeeded by the present manager, I. Sugimoto. For some time Dr. J. Kojima was acting general manager. It is necdless to say that the gentlemen mentioned are all members of the Institute, as is also Baron T. Furukawa, president of the company. Since the discovery of the enormous masses, called "kajika" or "bullhead" deposits, which the writer has described elsewhere,' the mining methods have been varied to meet the different conditions presented by these deposits. The Ashio Ore The country rock of this mine consists of the middle Chichibian slate and quartzite into which has been intruded a post-Tertiary plagio-liparite neck more than 2 mi. in diameter, in the shape of an inverted cone which narrows downward to a relatively small diameter in depth.

Jan 1, 1923

By J. D. Forrester

SINCE the introduction of the first percussion rock drill in about 1850, drilling equipment has undergone a progressive evolution so that a wide range of special classes of machines now are marketed by several manufacturers. Essentially all of the drilling machines presently employed for blasthole drilling are of the hammer-drill type. They are classified as hand-held hammers (jackhammers, sinkers, etc.), drifters (light or heavy), and stopers and are of many sizes; varying in weight and rotative and blowing power. Most makes of drill machines fundamentally are the same in principle of operation as they are designed to strike a blow on the end of a drill rod in the manner of early-day hand drilling. However, beyond this common characteristic, the similarity among different makes ceases. In choosing between similar machines of one make or another, it is important to remember that rock drill manufacturers have not attempted to standardize drill parts, the result being that a mine operator must approach, because of replacement parts, standardization by limiting the makes of machines used. The present-day selection of any particular drilling machine is dependent fundamentally on its inherent ability to make a hole, or series of holes, as speedily and as cheaply as is possible. Two categories of controlling elements become apparent in any analysis devoted to making the choice of a drill, namely: 1-Conditions under which the equipment is to be used, such as mining method practiced, type of labor available, character of rock material. 2-Physical characteristics or features of the given drilling machine. Regardless of the controls of class 1, above, the elements of this category are fixed by several factors. All of them are interrelated and, though some often are more important in one case than in another, an unfavorable variation of any-others being essentially equal-is sufficient to discredit the optimum applicability of the particular drill machine. The relative factors in the selection of a machine are as follows: First cost-This is not generally an important item on a comparative basis as the marketing of drill machines is highly competitive and most makes are priced closely.

Jan 1, 1952

By W. D. Robertson, H. H. Uhlig

The intermetallic compounds MgzSn and Mg2Pb are two of the important series of stoichiometric compounds which magnesium forms with elements of the fourth group of the periodic system. Since there is a complete series of compounds, all possessing the same comparatively simple structure, a unique opportunity is presented to study their properties with respect to increasing atomic number of the anion as it varies from silicon and germanium, through tin and lead. The present work deals with the two lower members of this group, and it is hoped eventually that additional data regarding the silicide and germanide will be obtained. The results of such a complete study provide part of the essential basis for the empirical correlation and theoretical treatment which, in other systems, has contributed to an understanding of inter-metallic compounds and the metallic'state in general. Some experimental data are already available in the literature. However, they are fragmentary and limited in significance owing to the methods of preparation employed and the impure materials available at the time. It was our objective, therefore, using pure metals and improved metallurgical methods of preparation, to produce stoichiometric compounds of high purity for the study of their electrical and chemical properties. We felt that a detailed investigation of chemical properties, about which relatively little is known, combined with electrical properties, would be a significant contribution to the understanding of these compounds and in particular to the mechanism of corrosion associated with types of bonding in alloy systems. The chemical studies are reported elsewhere. Previous Investigations Previous work concerning the electrical properties of these compounds was undertaken in connection with the establishment of the two phase diagrams which are available in Hansenl and Beck. The first comprehensive investigation of the electrical conductivity of magnesium-tin and magnesium-lead alloys was made by Kurnakov and Stepanov.3 This was followed by Grube and Voss-kiihler4 who studied electrical conductivity and thermal expansion over a wide range of temperature and who, unlike Stepanov, appreciated the significance of the large solid solubility of tin in magnesium and took some precautions to obtain an equilibrium state. However, at the time these investigations were made, neither pure magnesium nor

Jan 1, 1949

By F. W. McQuiston, L. J. Bechaud

3.2-1. Introduction. Much has appeared in the technical literature on theory of sampling (18, 37), weight of sample required in relation to particle size (28), probability of error in sampling (3), and statistical analysis of sample data (20). Each industry, whether it be copper, iron ore, or coal, has its own standards and methods. All of the rather extensive theoretical treatments appearing in published literature on sampling apply to material already on hand such as coal, iron ore, or copper concentrates in rail cars, or in moving streams such as on conveyor belts. The attempt usually is to apply statistical techniques in order to improve reliability and precision in sampling, and to reduce differences between the analyses of seller and buyer. In contrast to this type of sampling, very little has appeared in the literature on sampling a virgin deposit from the metallurgical point of view. Perhaps it would he more descriptive to designate this point of view as "Gm-metallurgical," since geology is inextricably interwoven with metallurgy in gaining an understanding of the complexities of a deposit, eventually leading to a definition of mineable reserves, with the development of a flowsheet and engineering criteria for the planning of a successful and profitable operation. The degree of cooperation between these two departments often determines whether the processing plant is a success at the inception of operations, or whether expensive changes and modifications must he made, with the plant finally reaching rated capacity at some later date. The first concern of the metallurgical department should be to establish proper accreditation of the samples which will be used in any ore-testing campaign. It should he made mandatory, as part of operating management policy, for the responsible metallurgist to he aware of the significance of the samples and to become intimately knowledgeable in all aspects of metallurgical behavior and response to treatment of all varieties of ore in the deposit under consideration.

Jan 1, 1968

By Will H. Coghill

In this investigation, the low-grade red iron ores of Alabama were examined by the use of "heavy solutions."' Ores are generally ground preparatory to concentration and as long as the concentrators make suitable products the effectiveness of the grinding is likely to be unquestioned; but when suitable products are difficult to make, an investigation becomes imperative. In such a case a dissection of the ore might be made to find the cause of the trouble. Such a condition of unsuitable products exists in the low-grade red iron ores of Alabama. They are difficult to concentrate. To be sure it might be said that the concentration of iron ores is a new thing and that the ore-dressing methods are undeveloped, but a glance at the industry reveals an abundance of methods and devices for almost all imlaginable conditions. Concentrating machinery has not been tested in this investigation. When the properties of the ores have been gleaned, the machinery may be used more effectively. Alabama Low-grade Red Iron Ores The Bureau of Mines has undertaken by laboratory methods to select the best means of concentrating the low-grade iron ores of Alabama. These ores constitute the parts of the ore bed left by selective mining. If more of the ore bed could be included in the current output, the mining cost would be reduced and longer life of the district would be insured. This advantage would be reflected by added permanence of churches, homes, schools and every undertaking in the commonwealth. The red ores chosen for this study of effectiveness of grinding are too low in lime to meet the requirements of the blast furnace. If lime is

Jan 1, 1927

By Sidney Powers, Alfred C. Lane

This paper aims to present the results of an investigation concerning gravitative differentiation in lava flows, based on a quantitative microscopic and chemical study of a Triassic basalt from Nova Scotia, and confirmed by data secured from a study of certain Keweenawan ophites. At Cape d'Or, Nova Scotia, near the head of the Bay of Bundy, marine erosion has exposed a series of Triassic basalt flows in which copper has been sought for a number of years. Studies of the thickest flow of the series with regard to volumetric composition, specific gravity, and grain have been made by the junior author, and measurements by students at Tufts College, together with confirmatory observations of the same nature on this and other flows by the senior writer, and chemical analyses made by the Division of Chemistry, Mines Branch, Ottawa,' all show differentiation in lava flows comparable to that in intrusive bodies. The work was made possible by the availability of the drill-cores, the property of Tufts College, and emphasizes the desirability of the study of drill-cores from other localities. Measurements of the specific gravities of certain Keweenawan lava flows of Michigan by the senior author, from material collected in 1915, will be given as a comparison to those of the Cape d'Or flow. It has been found that the specific gravity of drill-cores, or volume per cubic foot, can be readily obtained by measuring their dimensions. This can be done to an accuracy of within 1 per cent. in pieces of core over 100 mm. in length by using a micrometer gage for the diameter, and taking the average of six measurements of the diameter; and the average of four measurements of the length made with a finely graduated ruler. Then, after weighing them, the weight in grams per cubic centimeter, or what is practically the same thing, ounces per cubic foot, is obtained. System-

Jan 1, 1916