Search Documents

By Robert L. Braun, Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides, chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 100° to 150°C. The rate of dissolution of chalcopyrite exposed to oxygen-saturated solutions becomes so rapid under these conditions that the rate of copper extraction becomes limited by the accessibility of chalcopyrite to the solutions. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, and size of ore particles. It is concluded that the high pressure and high temperature obtainable in a large ore mass broken by nuclear explosives promise the rapid and economic recovery of minerals not considered soluble by conventional in-situ leaching methods. The method should be broadly applicable to the kinds of deep deposits that must be depended on for future production and with minimum disruption of the environment.

Jan 1, 1974

By A. L. O’Neil, J. A. Wineland, A. B. Arnold

Movement of water through the Tehachapi Mountains was one of the most challenging parts of the planning, design, and construction of the California Aqueduct. The California Aqueduct is the main artery of the California State Water Project, which will move water 444 miles from the Sacramento-San Joaquin Delta into the arid and semiarid, densely populated parts of Southern California. The $2,000,000,000 project, designed and constructed by the California State Dept. of Water Resources, was started in 1957 at the Oroville Dam site and is now well past the halfway mark in construction. Water is now being delivered from the California Aqueduct to portions of the San Joaquin Valley. The California Aqueduct is scheduled for completion in 1972. Tunnels on the Tehachapi Crossing are often overshadowed in engineering descriptions of the Crossing by the tremendous importance and engineering significance of the Tehachapi pumping plant which will pump water through the tunnel system. For purposes of this paper, it will suffice to say that the plant is designed to lift 4100 cu ft of water per sec up approximately 2000 ft, making this the highest pumplift in the United States and one of the largest in the world. Water will be moved from the pumping plant through twin tunnels called the Tehachapi Discharge Lines to the top of the lift. From here, water will flow through four additional tunnels which are all linked by short connecting structures (Fig. 1). The tunnels are referred to as Tunnels 1, 2, 3, and Carley V. Porter Tunnel. HISTORY Selection of the final route of the Tehachapi Crossing was the result of comprehensive investigations beginning in 195 1. Numerous tunnel

Jan 1, 1970

By J. G. Puterbaugh

MARCH 31, 1922, undoubtedly will be long remembered as the ending of an important epoch in the coal-mining industry. On that date, contracts fixing the wages and terms of employ-ment at all anthracite mines and at approximately 60 per cent. of the bituminous mines of the country expired. For the past two years, the consuming public has been complaining bitterly against continued high cost of coal. Coal operators employing union labor have felt obligated to carry out contracts entered -into under the direction of the Bituminous Wage Commission appointed by President Wilson, and in order to do this, they have sacrificed millions of tons of business to non-union mines, and millions of dollars in wages that would have been distributed throughout unionized districts have been diverted to the non-union miners, many of whom never obtained the peak wages granted by the Bituminous Commission and others of whom accepted reductions early in 1921. Heretofore, wage contracts have overlapped as to expiration dates in different districts and renewals have had to take into consideration the competitive balance; the present situation is unique in that practi-cally every contract in the country expired on March 31, and the questions now confronting those responsible for the operation. of the coal mines of the country are: 1. Shall the operators that have heretofore employed union labor endeavor to continue contractual relations with United Mine Workers of America? 2. Shall they undertake to operate their mines with non-union labor? 3. Shall they encourage and endeavor to work out some plan of regulation or arbitration by a Government commission such as President Roosevelt appointed to settle the anthracite strike in 1902? 4. Shall the country give consideration to the demand of the miners that the coal-mining industry be "nationalized?"

Jan 5, 1922

By E. R. Phelps

A determination of feasibility of a new surface mining project requires a study in orderly fashion through the procedures outlined in Section 2 and the previous two chapters of this section. The information and data collected as described in Chapters 3.1 and 3.2 must be correlated, and the many variables that affect the venture must be reviewed. This review will furnish the mining engineer with the information required to make a preliminary evaluation of estimated profit in the venture. It is at this time that management must make yet another decision whether to drop or continue the project. 3.3-1. Maps. For the purpose of collecting, outlining, and correlating a large portion of the data required for a surface mining feasibility study, maps are essential. A map to a mining engineer is like a sheet of music to a musician, or a blueprint to a designer. It provides a pictorial method of presenting mining information not only for practical application in estimating and planning, but also for demonstration of physical relationships to those charged with decision-making responsibilities. GENERAL AREA MAP. The first step in the process of graphic information assembly is the preparation of a "small scale" general area map. Such a map may cover a mining district, a market area, a watershed area or district, or the whole or a section of a geologic feature such as an iron formation or coal seam. An example of such a general area map is shown in Fig. 3.3-la which outlines the various coal mining areas in the vicinity of a proposed "mine-mouth" power station, the Liddell Power Station Project. If Quadrangle Maps of the United States Geological Survey, or their equivalent, are available for an area, a common and very effective technique is to superimpose mining data on these maps, either directly or by means of transparent overlays. Valuable topographic information

Jan 1, 1968

PRESENTATION of the 1922 Washington Award to Capt. Robert W. Hunt, honorary member and twice president of the Institute, was made at the annual dinner of the Western Society of Engineers, in Chicago, on June 18, 1923, in the presence of 250 mem-bers and guests. W. L. Abbott, Chairman of the Award Commission, when delivering the presentation address, said The life of the Govern-ment of this country, as the lives of governments are usually measured, is short, barely 150 years, but meas-ured by what it has accom-plished, this country has reached a venerable age. The first 75 years of our country's existence were necessarily preparatory to the greater developments which came in the second, and that last half of our country's existence is ex-ceeded, by ten years, by the span of life of our honored guest. "Very little iron and steel were produced in this coun-try until after the birth of Robert W. Hunt. And it was not until after 1860, when as a boy of 21 he joined his fortunes with those of the Cambria Iron Works, that the iron and steel business of the country really took root. After a year or two with the Cambria Works, he left a promising position to go into the army, where he served for four years. After the close of the war he returned to the iron works and qualified himself as a metallurgical chemist.

Jan 7, 1923

By Lester C. Uren

Today, a dozen or more universities and colleges in the United States are offering curricula designed for the specialized training of engineering students who plan to enter the petroleum industry. Many hundreds of students are following these curricula in their academic preparation, with the expectation that by so doing they will be better equipped to enter the petroleum industry in an engineering capacity than their competitors that seek to do likewise with training of less specialized character. Those who have helped plan and develop these curricula believe that such specialization should and does afford the student a superior preparation for his task. Others have questioned this and urge a broad preparation in fundamentals without specialization. Still others are suggesting even greater specialization than present petroleum engineering curricula afford. Some would have the student first prepare himself in one of the more general divisions of engineering, such as civil, mechanical or electrical engineering, and then seek some degree of specialized preparation in a graduate program. Which of these views is correct; or, if there is merit in each, which plan offers the greater advantage to the student? It is time that we paused to take stock of our objectives and of our way of attaining them. Is the training received by our petroleum engineering students what it should be? To what extent is the product of our petroleum engineering schools meeting the requirements of the industry? How may graduates be better equipped for the work they are called upon to do? These are questions that educators interested in the training of petroleum engineering students are ever asking. They must depend upon engineers and executives engaged directly in the industry for advice and helpful suggestions in better planning the training to be offered to our future engineers. This paper will have served its purpose if it is successful in focusing attention of men active in the industry on some of these educational problems, to the end that the ideas of men close to the needs of the industry may be made known to those who have responsibility in the control of our educational programs.

Jan 1, 1937

By L. S. Darken, H. A. Wriedt

In a previous paper,1 an experimental study of nitrogen dissolved in a cold-rolled ad heat-treated, low-carbon steel at 300° to 450°C yielded the equilibrium solubility relations and the concentrations of the two types of deject sites involved. In this paper, the probable identities of the defects that absorb nitrogen are restricted from the available evidence to screw dislocatioms for B sites, and to either micro crack surfaces or edge In a previous paper.' we reported an experimental study of the excess nitrogen solubility in a low-carbon steel produced by a combination of plastic deformation and nonrecrystallizing heat treatment. The concentrations of the defect sites that absorb the excess nitrogen were measured in terms of their capacities for nitrogen. Also measured were the equilibria of nitrogen distribution among the sites. Several problems and questions arise from these measurements. We should like a physical identifi- dislocations for A sites. The concentrations of these defects in experimental steel specimens are estimated from the concentrations of defect sites. finally, the influence of chemical composition upon the nitrogen-trapping defects—the relative numbers generated in deformation, the relative numbers surviving as temperature is raised, the apparent numbers observed, and the distribution equilibria-is discussed. cation of the defects involved and of the two kinds of nitrogen-absorbing sites, called A and B types, upon those defects; the concentrations of the defects themselves could then be computed. We should also like to know how exclusively the findings apply to the "X steel" used in the experiments and to what extent they apply to cold-rolled steel given no subsequent treatment. By considering the data already given, together with results from a few specific tests which will be reported as they are invoked, we are able to eliminate some interpretations altogether and to secure an acceptable though limited interpretation from among the remaining possibilities.

Jan 1, 1965

By Henry F. Hebley

INTRODUCTION How often has the thoughtful observer pondered the apparent contradictions experienced in the weather? One can take records of two days, one in the winter and one in the summer. The "degree days" indicate that space heating and domestic load were present in one case and not in the other. The Business Index may be about the same, indicating that the industrial activity of the area and its concomitant use of fuel were about the same. Thus the volume of the products of combustion released to the atmosphere varied only as related to the space heating demand. Yet on one day in winter the atmosphere may be clear and bracing, while on a summer's day the air is thick and murky and the visibility sharply reduced. The situation may be reversed. What are some of the factors that contribute to the creation of these conditions? These few notes have been prepared to indicate some of the influences that are exerted on the problem. THE SOURCES OF ATMOSPHERIC POLLUTION The industrial area of Pittsburgh, Pa., has been a dominant center for the production of iron and steel for over one hundred years. In fact, with the growth of the numerous auxiliary processes Allegheny County which contains Pittsburgh is probably the most industrialized county in the world. In addition, the type of manufacture carried out in this area is predominant dependent on thermal energy (heat). That energy is supplied from coke and coal produced in the vicinity of Pittsburgh. Indicative of the stupendous quantities of fuel that are employed in this industrial area's economy, the following (Table No. taken from the U. S. Census (1940) may I of interest. An influence that has never been fully appreciated by many individuals is the fact that no matter what adventures the gases of combustion experience as they pass through the various processes, ulti¬mately the spent gases are discharged through chimneys to the atmosphere.

Jan 1, 1948

By Raymond D. Daniels, Frank E. Rizzo, James D. Gerber

ThIS discussion describes a method for the addition of small amounts of oxygen to columbium (niobium) in an accurate and reproducible manner. The method is based on the complete reduction by columbium of a carefully weighed amount of another metal oxide. The equilibrium Pq associated with Cb-CbO mixtures is extremely low, e.g., 10"25 atm at 100O°C, and the pressures over Cb-0 solutions are even lower. The equilibrium Pq associated with a given metal-metal oxide mixture can be easily obtained, with the aid of a Richardson-Jeffes chart.' Although columbium should effectively reduce almost any metal-metal oxide combination, the proper choice of a metal-metal oxide system is complicated by the low rate of oxygen transport in the gas phase at low oxygen pressures and the difficulty in reducing any columbium suboxide formed during the reduction of the oxygen source material. Thermodynamically, oxide formation on columbium will be avoided so long as the oxygen partial pressure over the columbium is below the equilibrium pressure associated with the mixture Cb-CbO. The logical choice of a source for oxygen would appear to be a mixture of Cb-CbO, since oxide formation would be precluded by nucleation difficulty. But calculations using the kinetic theory of gasses indicate that, for a temperature of 900°C, the reaction would proceed too JAMES D. GERBER, formerly Research Assistant, University of Oklahoma, Norman, Okla., is Research Metallurgist, Air Force Weapons Test Laboratory, Kirtland Air Force Base, N. Mex. FRANK E. RIZZO, Junior Member AIME, formerly Assistant Professor of Metallurgy, University of Oklahoma, is Associate Professor of Metallurgy, University of Texas at El Paso, El Paso, Tex. RAYMOND D. DANIELS, Member AIME, Professor of Metallurgical Engineering, University of Oklahoma, is an NSF Fellow, Institute de MBtallurgie Structurale, Universite de euch:tel, Neuchitel, Switzerland. Manuscript submitted October 28, 1968. IMD

Jan 1, 1970

By P. E. Baker

A paper by A. S. Odeh' expounds a capillary-flow theory which purportedly provides a mechanism whereby relative permeability depends on oil-water viscosity ratio and may be greater than unity for high viscosity ratios. Core-measurement results are presented to support the theoretical development. This paper presents arguments to indicate that (1) the theoretical treatment is basically incorrect, (2) data reported are insufficient to support the conclusions and (3) literature cited does not support the theory or the conclusions. PROPOSED MECHANISM The essence of Odeh's theory is that oil flows as a filament along the central portion of a straight, uniform capillary of radius r filling the tube to a radius ri. Surrounding the filament of oil is an annulus of water in which exists vortex motion but no net flow. The water is described as being in "microscopic but not macroscopic" motion. The oil filament is aided in its flow by moving upon the water vortexes as if on roller bearings. This process is presented as a steady-state flow condition. The first objection to the existence of vortexes in the presumed water layer is that the theory provides no mechanism whereby they can be established. This fact was mentioned by C. F. Weinaug in a discussion published with Odeh's paper. The capillary contains no irregularities or obstructions, and the water is not presumed to be in turbulent flow. Apparently, cylindrical symmetry is assumed; therefore, the supposed vortexes must be toroidal, the line of zero velocity being a circle concentric with and in a plane perpendicular to the axis of the capillary. This is a rather difficult picture to accept. The author referred to Yuster's statement' that he had observed the "spinning in place" of otherwise immobile water. Yuster's article does not describe the conditions under which this motion was observed or the means used to observe it. However, the article does make clear that the observed motion was not in a straight, uniform capillary but, rather, apparently oc-cured in some kind of dead-ended pore space. Obvious- ly, such a report cannot be considered as support for Odeh's concept of two-phase capillary flow.

By E. G. Woodruff

(Butte Meeting, August, 1913.) FEW authors of treatises and papers on engineering subjects have . given adequate attention to topographic maps.. The statement applies especially to mining engineering in all branches. Even those who have discussed such maps have treated the subject only in a general way. Therefore it is proposed to outline in this paper a few of the uncommon, yet important relationships which topographic maps and their by-product, structure-contour maps, have to modern methods of mining investigation and development when the facts depicted on such maps are properly interpreted. Topography, as suggested by the etymology of the word, menus a detailed description of particular places. Written descriptions have been found less effective than the pictorial representations, therefore attempts have been made in various ways to picture the surface features of places. Lines and shading have been used, hachures drawn, and, finally, the contour topographic map. To a large extent this style of snap is the result of the demands of engineers. It is designed to meet their needs far more than those of the man untrained in engineering. In fact, the average man obtains a better idea of the topography of an area from the hachure system than from contour maps. . Since the maps. have been made chiefly for the use of the engineer, they ought to meet his demands on the one hand, and, on the other, should be used by him to the fullest extent. Such maps, when properly made, accurately portray a portion of the earth's surface and should present the topography better than a personal examination of the area without a map could present it, because the person making such examination views only a limited portion of the surface at a time, and estimates distances only roughly with his eye. Let the engineer consider carefully the fact that in many instances the topographic map is superior to a personal examination of the surface features of a property because the map is based on careful instrumental measurements, whereas the eye gives imperfect data because it can be used merely for the estimation and

Jan 6, 1913

By Edmund Newton

The steel industry of the United States has depended in the past almost wholly upon imports for its supplies of manganese. Many of the important domestic sources yield ores leaner in their natural condition than the foreign ores the steel industry. has been accustomed to use. To make them available, therefore, either the ores must be concentrated or the practice of the steel industry modified. Roughly 25,000 T. annually of high-grade manganese ores are used for dry batteries for chemical purpose, and in other ways; while approximately 750,000 T. are required for making steel. , By present practice, every ton of steel takes an average of about 14 lb. (1.8 kg.) of metallic manganese. This is generally added to the steel in the form of an alloy, the standard alloys being the 80-per cent. ferro-manganese and the 20-per cent. spiegeleisen, During the year 1917, 286,000 T. of ferromanganese and 193,291 T. of spiegeleisen were made in this country, the former largely from imported ores; and 45,381 T. of ferromanganese. was imported. The metallic manganese represented by these alloys was 304,000 T., the product of roughly 800,000 T. of high-grade ore and 345,000 T. of low-grade ore. Manganese Deposits in the United States Before the war manganese ore was mined in relatively small quantities in the Appalachian region, including Virginia, Tennessee and Georgia, and in Arkansas, but owing to the increase in prices during the past three years manganese mining has been undertaken also in Montana, California, Arizona, New Mexico, Nevada, Utah, and Minnesota. From data now available it appears that in this country deposits of high-grade manganese ores are usually small, while materials lower in manganese and higher in iron occur in appreciable quantities. Our total quantity of manganese-bearing material is relatively large, but on

Jan 1, 1920

By H. S. Munroe

To those familiar with ore-dressing practice, it is hardly necessary to dwell upon the importance of the jig. Within its proper sphere no substitute has been found that does the work as well or as cheaply. Its capacity is large, it requires but little attention, and the losses are small. In one form or another, it is the principal machine used in the concentration of low-grade ores, and for the separation of one metallic mineral from another; and it is almost the only machine used for the purification of coal. The present paper is a study of the action of the jig in the light of results obtained in the Lake Superior copper mills, ad at the St. Joseph Lead Co.'s dressing-works, in Missouri; and a description of experiments undertaken with the view of reproducing and isolating the conditions of jigging, in order to develop the laws which underlie the process. There are two recognized systems of jigging, the English and the Continental or German. The English system is a development of the hand-jigging formerly employed in Cornwall and other metalliferous districts of England, and introduced by English miners to this country. In this method the crushed ore, coarse and fine together, is first jigged oh a

Jan 1, 1889

By William Hilliard

IN any manufacturing business, it is of vital importance that the management should know the exact cost of the units of production. Without such knowledge, a company can sell blindly in the open market, obtaining the best prices it can in competition with other firms, and manage perhaps to continue in business for a time; but at any moment, and especially in a period of falling prices, such a firm is at a loss to know exactly at what point it can sell at a profit and exactly how much it is losing per unit if it sells below that point. Furthermore, it is necessary not simply to know the exact total cost per unit, but to know definitely all the different-factors which enter into that cost. A firm manufacturing pocket knives had been doing a profitable business for many years when it began to earn smaller and smaller profits, until there was scarcely any profit at all being realized. Being unable to determine exactly what its future policy should be, it called in experts who studied the past records carefully and followed out for a period a better cost, system. Investigation then showed that on several different kinds of knives in common use, a small profit per unit was being made. On a number of special kinds of knives, of which the firm was very proud, it had been forced to cut prices under the pressure of outside competition and had believed that a small profit per unit was still being made on that product, while a detailed cost analysis showed that a loss was being incurred on each knife of that kind produced. It then became clear that the company must either give up the special line and concentrate wholly on the cheaper knives and extend their sales to territory not yet developed; or expand its plant and produce more of the higher grade knives and thus lower the cost per unit enough to make money on the higher grade knives also, if conditions warranted such expansion. Investigation revealed that the market for large quantities of the high-grade -knives was decidedly uncertain and that the most promising move would be to manufacture only the less expensive knives on a larger scale. That plan was carried out and the concern began again to make a better profit.

Jan 1, 1932

By E. R. Gilliand

KNOWLEDGE of a large number of the physical properties of the hydro-carbons is needed in the calculations and studies of the production engi-neer. Since experimental data on these properties of the individual hydrocarbons and their mixtures are available in only a relatively few cases, the use of generalized correlations has developed rapidly in the last decade. The generalized correlations of pressure, volume and tem-perature,1 enthalpy,2 and vapor-liquid equilibria,3 on the basis of reduced temperatures and pressures, are outstanding examples of this develop-ment. These correlations are of particular value to the production engineer interested in the flow of oil and gas, since they can be used to estimate the conditions under which segregation of phase occurs as well as the composition, density, and relative amounts of the phases. The technique of using the correlations for such estimations has been pub-lished by several authors¢ and will not be considered in this paper. A considerable number of data have been obtained to check the generalized pressure-volume-temperature correlations, and these data indicate that such relations hold for the hydrocarbons from methane to heptane. The accuracy is in general sufficient for most engineering pressure-volume-temperature calculations. However, the generalized correlations of enthalpy and vapor-liquid equilibria have in general been developed from the pressure-volume-temperature correlations by thermodynamic calculations and only a relatively few experimental data are available to check these calculated values. The calculations from pressure, volume and temperature are likely to lead to large errors in the calculated enthalpy and vapor-liquid equilibria. Thus, in the calculations of enthalpies, slopes of the pressure-volume-temperature data are employed, and determining these slopes can greatly amplify small errors in the original data. In the vapor-liquid equilibria calculations it is necessary to have the pressure-volume-temperature relations of the mixture, and the latter properties are much more questionable than those of pure components, particularly in the critical region. A considerable number of experimental data are

Jan 1, 1939

By C Gunther

Many definitions have been advanced and many limitations advocated in the use of the terms, veins, lodes and ledges. The following definitions appear to follow the best usage. A fissure vein, according to Lindgren, is a mineral mass tabular in form as a whole, though often irregular in detail, filling or accompanying a fracture or series of closely set and intimately related parallel fractures in the enclosing rock, the mineral mass having been formed later than both the country rock and the

Jan 1, 1932

Your outgoing President, following the worthy example of distinguished predecessors, submits a reckoning of his stewardship. He renders this fully realizing that without the hearty cooperation of Directors and Secretary, which he here recognizes most cordially, no President, who at best is but a passing force, can achieve markworthy results. The details as to your membership, finances, intellectual output, and,-other activities, have been submitted in the report of the Secretary.* It is enough to emphasize that during the year just expired, your organization has held two of its most successful meetings-one the largest in its history-has produced the largest number of papers, eliciting most interested discussions, has enjoyed its greatest income; and has received more than one thousand new members-passing the best previous record by more than one hundred, and exceeding the average increment of the, past five years by one third. It closes the year with 6528 members, the largest enrollment in its history. All of this might be true and yet the intellectual and social spirit, the loyalty of membership, the real life of the organization, might remain stagnant. As to these, it is for others than your speaker to testify. No comparison is feared.

Jan 3, 1918

By J. A. Herbst, K. Rajamani, M. Siddique

This paper presents an investigation of the accuracy of population balance model predictions for ball mill scale-up. Experiments performed in 25.4 x 29.2 cm (10 x 11.5) batch mill are used to estimate linear grinding rate parameters that, in turn are scaled according to specific power draft to predict performance in 381 x 292 mm (15 x 11.5 in.) and 762 x 457 mm (30 x 18 in.) batch and continuous ball mills, respectively. Results are presented for wet and dry grinding of two homogeneous solids, limestone (soft) and quartz (hard), and one heterogeneous solid, a complex molybdenite ore. In all cases good agreement between predicted and experimental product size distributions was obtained.

Jan 1, 1983

By A. E. Harnsberger

I is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practically every refinery operation, from the charging of crude oil to a distillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from — 50" F. to 900" F. Pressure may vary from subatmospheric to 2000 1b. per sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature may be divided into three parts: (1) extremely low temperatures of the order of —50" F.; (2) temperatures at atmospheric or slightly above; (3) temperatures from 200" to 900" F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250" F. The second type of corrosion occurs in high-temperature pumping equipment, with temperatures from 450" to 900" F., largely caused by sulfur compounds. There are also other corrosive conditions met with in refinery operations, particularly in the handling of acids, acid sludges and other specialized processes. These problems, although difficult to

Jan 1, 1935

By R. M. Brick, M. A. Williamson

Certain features of the response of copper and brass to deformation and recrystallization remain obscure. The textures obtained on rolled sheet are listed by Schmid and Boas1 as: No adequate explanation has been advanced for the presence of the secondary deformation texture of copper and its absence in brass or for the origin of the cubic recrystallization texture of copper.2 A recent publication3 attempted to rationalize the above empirically described annealing texture of brass on the basis of retention of the (110) [112] rolling orientation plus twinning about the central octahedral poles of the usual secondary (110) [115] orientation. The difierence in the textures of annealed copper as compared to 70-30 brass is also shown by the difference in the position of ears for drawn copper, at o° and go", as compared with drawn brasses, at 45o, for all compositions between oo-10 and 70-30.4 Data on indi- vidual crystals are as yet too few to permit of an analysis of these textures comparable to that of mild steel as made by Barrett and Levenson.5 Experimental Methods The materials studied included copper specimens cut from the central, equiaxed crystal portion of a tough-pitch wirebar; brass made from this copper and high-purity (99.99 per cent) zinc including alloys of 7 per cent, 15 per cent, 24 per cent, 29 per cent and 36 per cent Zn and large single crystals of 70-30 bras. Sections 1/4 in. thick of the cast polycrystalline copper and brasses were reduced 40 per cent by rolling, recrystallized to a common grain size of 0.045 mm. and then rolled directly to foil 0.002 in. thick. Hardness readings employing both the Vickers and Rockwell machines were taken at intervals during the reduction. For comparison, similar specimens were cross-rolled—i.e., turned through 90° for each pass—and comparable hardness data were secured. Finally sections from the single crystals of brass were cut to obtain the following initial orientations; these sections were rolled, hardness data secured and a complete micrographic record of structural changes obtained.

Jan 1, 1941