Search Documents

By S. Isserow

RECENTLY, a description of the wartime work in this laboratory on the U-Si phase diagram was published. This diagram was available earlier in the open literature; as were Zachariasen's crystal structure identifications for the compounds in the system. The uranium end of the phase diagram is shown in Fig. 1. The most recent work on this system has emphasized the peritectoid E phase, of particular interest for a number of reasons. The early work provided evidence of this phase's resistance to corrosion in water and of its slight ductility. Further information on these properties has been obtained here. Work elsewhere4 has provided evidence of stability under irradiation. This body-centered-tetragonal phase is relatively isotropic compared to the more usually applied a or ? uranium phases. Unlike the other compounds in this system, it contains no Si-Si covalent bonds.3 In addition, consideration on the basis of Pauling's concepts leads to the conclusion that in the E phase, uranium has a higher valence than in any of the other phases. Definition of the composition of the ? phase has been of prime concern in the study of this alloy. Evidence is presented below that its silicon content is slightly higher than that of stoichiometric U8Si, the composition frequently assigned this phase on the basis of Zachariasen's identification. This work on the composition required careful attention to the method of dissolving the alloy for analysis, since apparently low silicon contents could be found under certain conditions, see Appendix. Preparation: Melting, Casting, and Heat Treatment—Almost all the samples were from castings with a diameter of 13/4 or 2 in. and about 1 ft long, weighing 10 to 15 lb. The U-Si charge was melted by heating to about 1650°C in an induction heated vacuum furnace. Beryllia crucibles were used at first, but were replaced by zirconia-washed graphite as the technique of keeping the carbon content low enough (about 500 ppm) was mastered. The alloy was bottom-poured at about 1650°C into graphite molds. A few small buttons, weighing no more than 50 g, were prepared in a small arc melting unit.' Since cast material has a preponderance of uranium and U8Si2, heat treatment is necessary to ob-tain the ? phase by the solid-solid peritectoid reaetion. Once obtained, the ? phase is stable to room temperature, obviating the need for speeial attention to the method of cooling after epsilonization, see Fig. 1. It was found desirable to epsilonize at 800°C for a week. For some purposes, in which residual uranium and/or U8Si2 are tolerable, shorter periods may be adequate. The temperature of 800°C is not critical, since essentially the same results were obtained from 785° to 825°C. Further departure from this epsilonization range is inadvisable.

Jan 1, 1958

P. E. McKinney,* Washington, D. C.-Observation made after examination of a number of defective gun forgings, together with a history of their manufacture, has strongly suggested that so-called "flakes" and woody or fibrous fractures are not necessarily analogous and are often caused by entirely different conditions. While some flaked bars may show fibrous areas in the fracture, it does not necessarily follow that the conditions causing these areas are the same as cause the fibrous, or so-called laminated, structures so commonly met in gun forgings subject to transverse tensile test; the fibrous structure formed in some flaky bars are merely incidental to the conditions causing the flakes. It is believed that the so-called flakes, or bright silvery spots, are mainly due to inherent physical defects in the steel, which existed at the very origin of the steel, rather than metallographic defects caused by subsequent irregularities in mechanical or thermal treatment. While great care in forging and treatment may, in a measure, tend to overcome the evil effect of the defects, with many heats of ingots, no such precautionary measures are needed to produce perfect forgings- and with such heats of steel it would be impossible, no matter how carelessly handled, to produce intentionally a forging containing the defects commonly known as flakes. It has been found possible, on several occasions, to actually predict flaky forgings from an inspection f the ingot after it had solidified, and in such cases no amount of careful forging or heat treatment would prevent the occurrence of such defects in the forging. The inspection of the physical condition of the ingot, and especially the character of the shrinkage on. the top of the ingot, has been given too little thought and study in this connection.

Jan 5, 1919

By Nelson Severinghaus

Following the end of hostilities of World War 11, a resurgence of industrial and home building has given impetus to the use of many products of the stone industry. Shortage and high prices of some building materials such as lumber have aided wider acceptance of materials such as concrete products which have been relatively plentiful and which have not risen so rapidly in price. Ingredients for many of these substituting materials come from the stone industries, often from by-products of stone operations. Most of the tonnage of the stone industry in the State of Georgia comes from granite and marble. There are extensive dimension stone operations in granite in the Elberton and in the Lithonia areas. Building and monumental marble from the Tate area has been used throughout the country. Cutting operations in both types of stone have their by-products in faulty blocks and in spalls. In the State there are three large crushed-stone plants utilizing granite, One near Camak, One near Lithonia and one at Stockbridge. All have had excess fines Or in in the past but this excess is largely disappearing with development of new uses. At times this "waste" has amounted to as much as 20 pct of the stone quarried. Handling Of this large tonnage from point of screening out to storage piles presented a costly problem and large areas were taken up by the piles. Crushed 'tone is generally sold with a a narrow margin Of price over cost, so any elimination of disposal cost or increase of income by marketing of by-products is highly desirable. By-products of Granite Dimension Stone It sometimes becomes difficult to differentiate between main product and byproduct. In the cutting of granite dimension stone in the Lithonia district of Georgia, a considerable quantity of remnants of Uneven shape and size is produced. The larger of these pieces have long found use as building rubble, particularly for retaining walls and building foundations (Fig I), They are broken down to one man size by plug drilling and wedging and by hammer. In recent times, demand for this former by-product has grown so that quarries have been opened for the production of rubble as a main product. Local masons have attained skill in using these irregular shapes to form economical and attractive walls. Areas such as Elberton, Georgia, which do not have a large building market nearby, tend to accumulate piles of large pieces of reject stone. When a road job or other local construction offers a quantity market for crushed stone, a portable crusher works this material down to crushed aggregate. Spalls and finer chips from granite stone-cutting operations have generally found their way into crushers and thence to the many uses for crushed aggregate. One company near Lithonia started marketing the smaller by-product crushed sizes for chicken grit about ten years ago. This use has grown to nation-wide distribution and the tonnage is now so great that they have opened a large quarry with

Jan 1, 1948

By Nelson Severinghaus

Following the end of hostilities of World War 11, a resurgence of industrial and home building has given impetus to the use of many products of the stone industry. Shortage and high prices of some building materials such as lumber have aided wider acceptance of materials such as concrete products which have been relatively plentiful and which have not risen so rapidly in price. Ingredients for many of these substituting materials come from the stone industries, often from by-products of stone operations. Most of the tonnage of the stone industry in the State of Georgia comes from granite and marble. There are extensive dimension stone operations in granite in the Elberton and in the Lithonia areas. Building and monumental marble from the Tate area has been used throughout the country. Cutting operations in both types of stone have their by-products in faulty blocks and in spalls. In the State there are three large crushed-stone plants utilizing granite, One near Camak, One near Lithonia and one at Stockbridge. All have had excess fines Or in in the past but this excess is largely disappearing with development of new uses. At times this "waste" has amounted to as much as 20 pct of the stone quarried. Handling Of this large tonnage from point of screening out to storage piles presented a costly problem and large areas were taken up by the piles. Crushed 'tone is generally sold with a a narrow margin Of price over cost, so any elimination of disposal cost or increase of income by marketing of by-products is highly desirable. By-products of Granite Dimension Stone It sometimes becomes difficult to differentiate between main product and byproduct. In the cutting of granite dimension stone in the Lithonia district of Georgia, a considerable quantity of remnants of Uneven shape and size is produced. The larger of these pieces have long found use as building rubble, particularly for retaining walls and building foundations (Fig I), They are broken down to one man size by plug drilling and wedging and by hammer. In recent times, demand for this former by-product has grown so that quarries have been opened for the production of rubble as a main product. Local masons have attained skill in using these irregular shapes to form economical and attractive walls. Areas such as Elberton, Georgia, which do not have a large building market nearby, tend to accumulate piles of large pieces of reject stone. When a road job or other local construction offers a quantity market for crushed stone, a portable crusher works this material down to crushed aggregate. Spalls and finer chips from granite stone-cutting operations have generally found their way into crushers and thence to the many uses for crushed aggregate. One company near Lithonia started marketing the smaller by-product crushed sizes for chicken grit about ten years ago. This use has grown to nation-wide distribution and the tonnage is now so great that they have opened a large quarry with

Jan 1, 1948

By J. Chipman, N. J. Grant, R. Rocca

Desulphurization of liquid iron by reducing slags of the electric-furnace type was studied from 65 heats. Variations were made in basicity over a wide range and in FeO up to about 5 pct for their effects on desulphurization. The role of FeO in desulphurization from the blast furnace, to the electric furnace, to the oxidizing conditions of the open hearth is shown to fit a relatively simple pattern of behavior. THE mechanism which controls the desulphurization of molten iron by basic slags has been the object of several investigations. In particular, equilibrium determinations have been made both in the field of basic open-hearth slags, which have a high iron-oxide concentration, and in the field of blast-furnace slags which have a very low iron-oxide concentration. In both cases the desulphurization ratio has been found to increase with increasing basicity of the slags; however, the mechanism of desulphurization differs in the two cases. In basic open-hearth slags desulphurization occurs mainly as a partition of iron sulphide:&apos; FeS * (FeS) and the desulphurization ratio is approximately independent of iron-oxide concentration in the slag. In blast-furnace slags the concentration of iron oxide is very low as a result of the highly reducing conditions in which they are formed. The controlling reaction for desulphurization is then:2,3 FeS + (CaO) <=* (CaS) + (FeO) The slags of the reducing stage in the electric furnace have an iron-oxide concentration which is intermediate between blast-furnace and open-hearth slags. The study of the mechanism of desulphurization for these slags has been the object of this investigation. The importance of low (FeO) in the slag for desulphurization was first verified by Bardenheuer and Geller,& who found that high desulphurization ratios were obtained in highly reduced slags. It was recognized" hat iron oxide in the slag becomes a controlling factor in desulphurization only at FeO concentrations approximately under 5 pct. A recent investigation conducted by Buehl,7 upon the suggestion of one of the authors, confirmed this opinion from the results obtained from a heat conducted in a small arc furnace. In the present investigation, slags of very high basicity, such as often are encountered in the basic electric furnace, could not be studied, but equilibrium data have been obtained for slags in a wide basicity range. The iron-oxide concentration in these slags ranged from 0.08 to 15 pct and was controlled by the addition of silicon to the metal. Other constituents of the slags were mainly CaO, MgO, SiO2, A120,, and CaF,. The experimental technique was essentially the same as that of previous investigations.1 8-lo In an open magnesia-lined induction furnace, 65 lb of Armco ingot iron was melted. An atmosphere of hydrogen was maintained over the melt for 1 hr to bring the carbon content down to approximately 0.010 pct maximum. The bath then was exposed to air for 25 min to remove hydrogen. The electrodes were put in place, and the furnace was operated from this point on in an atmosphere of nitrogen. A synthetic slag was added to which additions of silicon and iron sulphide were made. A rate study conducted at the beginning of this investigation had

Jan 1, 1952

By Thomas G. Murdock

ETHIOPIA, the first country to be liberated from Axis domination, has recovered remarkably from the ravages of occupation and war. Mineral production has contributed significantly towards this recovery, as it has provided a means of obtaining foreign exchange and has given employment to hundreds of workmen whose maintenance otherwise would have presented a problem. Although primarily an agricultural country, never with a large mineral production, Ethiopia has within its borders a variety of minerals, both precious metals and nonmetallics. Some of these are important to the country as a national asset and others contribute greatly to local economy and can be expected to do so even to a greater extent in the future1 (Fig I). PHYSIOGRAPHY AND GEOLOGY The Empire of Ethiopia is essentially a mountainous and volcanic country, in northeast Africa, situated principally between latitude 4° and I5°N and longitude 34° and 44°E. It is bounded on the north by Eritrea, on the northeast by French Somaliland, on the southeast by Italian Somaliland, on the south by Kenya Colony, and on the west by Anglo-Egyptian Sudan. These European possessions thus completely surround the country. Its access to the Red Sea is through Eritrea; to the Gulf of Aden, through French or British Somaliland; and, to the Indian Ocean, via Italian Somaliland. These routes range in length from 40 to 250 miles. Ethiopia has an area of approximately 350,000 square miles, with a width from north to south of 625 miles, and a maximum length from east to west, along latitude 8°N, of about 875 miles. Physiographically the country is characterized by two very extensive sub-tabular plateaus: the Ethiopian Plateau to the northwest and the Somaliland Plateau to the southeast, separated by a long tectonic graben-the Rift Valley of the Galla Lakes and Danakil. The Ethiopian Plateau, deeply cut and notched by the drainage, slopes in a general northwest direction toward the Sudanese Plains and the valley of the Nile; the Somaliland Plateau slopes to the southeast, toward the Indian Ocean. The valley of the Galla Lakes and its extension to the northeast-the Awash River Valley, separates the plateaus, from Lake Rudolph to Danakil. This depression which constitutes a continuation or ramification of the Great Rift Valley of Central Africa joins in turn the trough of the Gulf of Aden and the Danakil-Eritrean Rift, continuations of the Red Sea and the Jordan Valley. The general basement of Ethiopia is made up of very old rocks, usually considered as Archaen.2 These rocks are represented by the metamorphic crystallines, such as gneisses, different kinds of schists, included lenses of crystalline limestone, and massive intrusives such as granites, diorites, and syenites, all cut by

Jan 1, 1947

By George E. Cole

While many parts of Canada&apos;s pre-Cambrian shield are well served by railway, it is frequently necessary for prospecting purposes to proceed farther into areas inaccessible by rail. To such areas in summer the canoe was at one time the accepted means of travel for the prospector while the dog team was much used in winter. Although summer travel was much improved by the development of the outboard motor, the lack of facilities for cheap transportation has been a serious hindrance to the employment of capital in opening up the distant fields. The pre-Cambrian surface of Manitoba, like that of Ontario, is hummocky, with rounded hills and ridges of rock alternating with basinlike depressions and valleys occupied by lakes and rivers Or by many low-lying portions covered with muskeg&apos; Routes to the mines have not usually been direct or easy and seasonal vagaries have presented problems in themselves. In summer, water transportation may be the cheapest method for the longer distances but it is not every water route that will satisfy the conditions of loading freight on to a boat or scow and of conveying it without interruption to its destination. By its location, a mine may require a large program of boat transportation in summer Over part of its route, to be followed by winter freighting for the remainder. In order to carry on development and produc- tion over a long period, it may be necessary to haul large quantities of supplies during the winter. This seasonal problem, particularly for the out-of-the-way properties, is SO important and demanding as to make it a major operation in the life of the mine. The -use of the tractor during winter months for heavy machinery and bulk supplies, and the use of the airplane throughout the year for the transportation of personnel and for emergency requirements, have greatly improved transportation to places that are inaccessible by rail. Canada has pioneered in both these methods. Development oF Transportation Twenty-two years have seen a marked change in transportation methods in Canada&apos;s mining country. Horse-drawn sleighs have given way to the tractor and that to some extent has been supplanted by the airplane. One of the earliest ventures involving transportation of considerable magnitude was that of the Mandy mine, on Schist at in northern Manitoba. According to accounts of early mining activities in Manitoba, the Mandy mine, beginning December 1916, had 3300 tons of ore hauled 40 miles by sleigh to Saskatchewan River and in summer this was conveyed by barge to The Pas, 130 miles, and then by railroad to Trail, British Columbia, 1200 miles. The mine shipped 6000 tons of ore in 1918 and 15,000 tons in 1919. In winter of the latter year, as many as 300 teams of horses were used on the 40-mile stretch to

Jan 1, 1943

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson&apos;s discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 7 3/4 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612° F. (322° C.), they reduced the 7 3/4 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statement just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson&apos;s time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced consumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opinions advanced by different authorities in the scientific world to account for the apparent anomaly, but none,

Jan 1, 1877

By George E. Cole

While many parts of Canada&apos;s pre-Cambrian shield are well served by railway, it is frequently necessary for prospecting purposes to proceed farther into areas inaccessible by rail. To such areas in summer the canoe was at one time the accepted means of travel for the prospector while the dog team was much used in winter. Although summer travel was much improved by the development of the outboard motor, the lack of facilities for cheap transportation has been a serious hindrance to the employment of capital in opening up the distant fields. The pre-Cambrian surface of Manitoba, like that of Ontario, is hummocky, with rounded hills and ridges of rock alternating with basinlike depressions and valleys occupied by lakes and rivers Or by many low-lying portions covered with muskeg&apos; Routes to the mines have not usually been direct or easy and seasonal vagaries have presented problems in themselves. In summer, water transportation may be the cheapest method for the longer distances but it is not every water route that will satisfy the conditions of loading freight on to a boat or scow and of conveying it without interruption to its destination. By its location, a mine may require a large program of boat transportation in summer Over part of its route, to be followed by winter freighting for the remainder. In order to carry on development and produc- tion over a long period, it may be necessary to haul large quantities of supplies during the winter. This seasonal problem, particularly for the out-of-the-way properties, is SO important and demanding as to make it a major operation in the life of the mine. The -use of the tractor during winter months for heavy machinery and bulk supplies, and the use of the airplane throughout the year for the transportation of personnel and for emergency requirements, have greatly improved transportation to places that are inaccessible by rail. Canada has pioneered in both these methods. Development oF Transportation Twenty-two years have seen a marked change in transportation methods in Canada&apos;s mining country. Horse-drawn sleighs have given way to the tractor and that to some extent has been supplanted by the airplane. One of the earliest ventures involving transportation of considerable magnitude was that of the Mandy mine, on Schist at in northern Manitoba. According to accounts of early mining activities in Manitoba, the Mandy mine, beginning December 1916, had 3300 tons of ore hauled 40 miles by sleigh to Saskatchewan River and in summer this was conveyed by barge to The Pas, 130 miles, and then by railroad to Trail, British Columbia, 1200 miles. The mine shipped 6000 tons of ore in 1918 and 15,000 tons in 1919. In winter of the latter year, as many as 300 teams of horses were used on the 40-mile stretch to

Jan 1, 1943

By C. G. Dunn

WITH respect to theories of recrystallization in metals plastically deformed, it has been said that the present status of this subject is far from satisfactory.1 It may also be said that before any mechanism of recrystallization for metals and alloys can be set forth in a satisfactory manner, there must be made available considerable data on orientation changes that occur during the deformation and recrystallization processes. Although extensive data have been published on recrystallization in single crystals and in polycrystalline specimens, more results of a type that can be classified according to simple orientation changes would be desirable in this complex field. It might even be said that before classifications are made according to types of orientation changes, it may be possible to classify a considerable amount of data into certain kinds of orientation states if groups of common or nearly common orientation occur. Methods for computing the probability of occurrence for various types of groups have been published2 and it has been pointed out in particular that it should be possible to analyze orientation data for high-order twin relationships between old and new grains even when agreement is not at all exact. In this connection, work on recrystallization in silicon ferrite reported in a paper concerned with complex groups of annealing twins&apos; indicated that some data were consistent with primary nucleation occurring according to a second-order or a third-order twin transformation. However, further work in this latter direction was definitely needed. It is, therefore, the purpose of the present paper to report data and analyses for primary nucleation in silicon ferrite following small deformations that have been carried out at the Pittsfield Works&apos; Laboratory of the General Electric Co. Analyses have been made with the aid of standard groups of twins that are reported elsewhere .4 PREPARATION OF SPECIMENS AND EXPERIMENTAL PROCEDURE The material used in the present investigation was taken&apos; from the same heat of steel as that used in a prior report.3 The finished strip in both cases was made by the Allegheny-Ludlum Steel Corporation according to methods that produce a high degree of preferred crystal orientation. Samples with large grains had the following composition: 3.45 per cent Si, 0.003 C, 0.008 P, 0.020 S, 0.075 Mn, 0.031 Al and 0.072 Cu. Thickness of specimens was 0.012 inches. Plastic deformation was produced by cold-rolling the samples on a mill with

Jan 1, 1945

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson&apos;s discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 79 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612&apos; F. (322&apos; C.), they redoccd the 79 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statenlent just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson&apos;s time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totsally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced colisumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opirlions advanced by different authorities in the scientific world to account for the apparent anomaly, bat none,

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By P. Shahinian, M. R. Achter

In a comparison of the creep -rupture properties of nickel in air arid in vacuum there is a reversal in relative strengths with variations in stress. At low stresses the properties are better in air while at high stresses they are better in vacuum. In the early stages of creep in a high stress test the specimen in air nzay have the lower creep rate but the one in vacuum is creeping at a lower rate in the later stages. A mechanism, involving two competing processes in terms of oxidation strengthening and weakening by surface-energy reduction, is proposed to explain these reversals. It had generally been assumed that, relative to their properties in air, the high-temperature strengths of metals would be increased in an inert atmosphere as a result of the elimination of the deteriorating effects of oxidation. However, several recent investigations have shown that the creep strength may be greater in air than in nonoxidizing gases. Pickus and Parker1 found that the creep rate of nickel was lower in air than in hydrogen or nitrogen. Internal oxidation was mentioned by Shepard and Schalliol as a possible cause for the longer creep life of Hastelloy C in air than in vacuum or helium. Sweetland and Parker, who observed lower creep rates for aluminum and copper in air than in helium, discuss the possible applicability of the dislocation-barrier mechanism to explain their results. Surface oxide layers may interfere with the escape of dislocations through the surface or with their generation there. In addition to showing the strengthening in air of low-alloy and stainless steel, and nickel and cobalt-base alloys, shahinian4 presented notch-effect data which indicate the role of stress concentrations; alloys of relatively low ductility were more sensitive to atmosphere strengthening when notched specimens were used. Although Bleakney&apos;s copper wires had a lower reduction of area in air than in vacuum, it is difficult to interpret his results in terms of strength changes since the stresses employed were not measured. In contrast to these data showing the strengthening in air, a number of investigations, most at relatively low temperatures, have demonstrated that the environment may cause a decrease in strength. These results are generally explained in terms of the effect of environment on surface energy. In a review of the subject, Benedicks and Harden use the concept of atomic bonding to explain how the adsorption of impurities would decrease the energy of a clean surface. A decrease in surface energy would facilitate the propagation of cracks or extension of the surface. Use of this mechanism is made by sato7 to explain the weakening of steel specimens bent in various liquids, by Potek and Shcheglakovs for the reduction of fracture strength of steel in molten metal, and by Benedicks and Harden for the reduction of strength of a variety of materials in a number of liquids. A similar explanation might be used for the results of Forestier and Clauss. The fracture stress of fine wires pulled in a variety of gases, including air, is lower than in vacuum. They attributed their results to the "tendency" for the gases to condense on the metal surface. That the strength of metals is affected by the type of gas in which the test is conducted has been demonstrated convincingly; the mechanism of the effect, however, is still uncertain. This investigation represents one in a series to explore the influence of variations in alloy composition and test conditions on the atmosphere effect in the expectation that the results would afford an insight into the processes taking place. To determine the effect of specimen composition, the present investigation was conducted

Jan 1, 1960

By T. Egleston

THE ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, how¬ever, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattle-snake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings ; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.

Jan 1, 1875

By Walter Craft, John L. Lamont

Adequate hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test&apos; and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann&apos;s principle2 for calculating hardenability from chemical composition; and Field&apos;s conversiona from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollen-back,5 Burns, Moore, and Archer,= and Burns and Riege1.l The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependcnt only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1947

By John L. Lamont, Walter Craft

Adequate hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test&apos; and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann&apos;s principle2 for calculating hardenability from chemical composition; and Field&apos;s conversiona from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollen-back,5 Burns, Moore, and Archer,= and Burns and Riege1.l The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependcnt only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1947

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

THE problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce light-weight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough so that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, particularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating." The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. Commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the purpose of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By Ted C. Briggs

Nitrogen exists in two broad categories commonly designated as elemental nitrogen and fixed nitrogen. Elemental nitrogen is found in nature as a diatomic molecule and constitutes about 78%, by volume, of the earth&apos;s atmosphere. Fixed nitrogen is a common term used for nitrogen that is chemically bound to other elements. Although elemental nitrogen is very abundant, nonleguminous plants cannot utilize nitrogen unless it is in the chemically combined form. The content of this chapter is confined to fixed nitrogen since the uses and properties of elemental nitrogen and the fixed nitrogen compounds are different. Bacteria associated with legumes are able to fix atmospheric nitrogen, but not to the extent or in the locations required by modem agriculture. The need to use fertilizers containing fixed nitrogen compounds to grow food crops has been recognized for hundreds of years, and from antiquity farmers have used organic wastes such as animal manures, vegetable wastes, sewage sludge, fish scraps, etc., containing these compounds for fertilizers. The organic materials have a low nitrogen content, however, and cannot support large-scale food production. Known commercial-size deposits of natural nitrates containing much higher nitrogen content exist only in Chile, and the possibility of the discovery of other significant deposits is remote. The Chilean deposits were the major source of nitrogenous fertilizers until about 1913, when the Haber-Bosch process for the production of synthetic ammonia was developed. In the Haber-Bosch process, nitrogen reacts with hydrogen, at high temperatures and pressures and in the presence of a catalyst, to form ammonia. At present Chile is the only country in the world with a nitrate mining industry, and, although the mining of natural nitrates is an important industry in Chile, natural nitrates are relatively unimportant, worldwide, because of the adoption of fixed nitrogen processes. The relative amount of the world demand for fixed nitrogen that is derived from natural nitrates has declined in recent years and will continue to decline. Modern farmers are sophisticated in economic calculations such as cost to benefit ratios and, for the most part, they purchase plant nutrients which give the highest return on their investment. Natural nitrates cannot compete on a fixed-nitrogen cost basis with anhydrous ammonia and its derivative products. In a limited sense, the fixed nitrogen industry is mining the air. Modern plants use air, water, and, in most cases, natural gas to produce the ammonia that is now the key building block of the fixed nitrogen industry. To present an accurate picture of the industry, this chapter on nitrogen follows a format somewhat different from that of other chapters in this volume.

Jan 1, 1975

By Thomas Egleston

The ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, however, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattlesnake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.