Search Documents

By Ellsworth Daggett

The ore smelted in the Winnamuck furnace during the year 1872 consisted, for the most part, of oxidized ores from the Winnamuck mine, only sixty tons of outside ore (from the Spanish mine) having been smelted. The latter, like the principal Winnamuck ore, was oxidized or so-called carbonate ore. There was mixed with these oxidized ores three hundred to four hundred tons, or 7 to 10 per cent. of galena, some of which was mined with the oxidized ore, while a part was mined separately from the lower portion of the mine, and afterwards mixed with the ore, with a view of preventing the formation of deposits of metallic iron in the furnaces. The average assay in silver of all the ore handled was 51.46 oz. per ton, most of it existing as chloride of silver. The lead contents were 34.98 per cent,, all, or nearly all, in the form of carbonate of lead. The relative amount of silver is not at all constant, the best silver ore often being poorest in lead. The predominant gangue was silica, several determinations of which have been made on representative samples, yielding in three such samples 26, 38, and 58 per cent. silica, the latter test being ore containing but little lead. The average contents in silica are about 35 per cent., with 6 to 7 per cent. sesquioxide of iron, and small quantities of alumina and lime. Mechanically, the ore was very fine, and so thoroughly disintegrated that it presented few distinguishing characteristics, rendering sorting or separating of ore from waste difficult, and often impracticable. Experiments on a small scale have been tried, with a view to separate the silica by washing; but these were unsuccessful, as the finest slime, requiring a long time to settle in still water, contained a large amount of silver; and on a careful sizing and washing of the sands and coarser parts, the silver contents were found to be less dependent upon specific gravity

By Truman Aldrich

THE Clinton group of the Silurian holds the red or fossiliferous ore; its outcrops have been mapped by the State or U. S. Geological Survey. This group is from 100 to 500 ft. thick in Alabama. There are places where it is entirely missing (doubtless islands in the Silurian Sea). In Etowah County, in part of Greasy Cove and vicinity, the upper seam is a coral reef impregnated with the red ore; in this same county, step, faults bring up the ore in three or four separate ridges practically parallel. In Blount County and on Raccoon Mountain, the ore runs under the carboniferous rocks and outcrops in the valleys. In examining some bore holes made in drilling for oil, the writer found the Clinton group continuing under the Warrior coal field wherever the drill has gone deep enough. It demonstrates the possibility of a source for red ore not seriously thought of until lately. The following bore holes made principally for oil, given in Bulletin No. 22, Geological Survey of Alabama, show the presence of either ore or red rock, and suggest vast resources yet to be outlined and developed for ore in the future. The locations are given by number on the map. Hole No. 1 was drilled 6 miles southeast of Russellville, Franklin County, by the Woodward Oil & Gas Co. It passed through 160 ft. of Clinton, but only a small show of red ore was found at 1280-1400 feet. A test well, No. 2, drilled near Atwood, Franklin County, in section 26, township 8, range 14, penetrated the Clinton at 1608 ft. and found 38 ft. of limy red rock, also 8 ft. of some blood red ending at 1820 ft., making 46 ft. of red rock in all. It is reported that some good ore was cut through but this work was done by a churn drill. The hole was continued by diamond drill from here. At least 400 ft. of the formation was classified as Clinton.

Jan 10, 1924

H. 0. HOFMAN, Boston, Mass (written discussion*).-The paper by Mr.. Pyne gives clear evidence of the difficulties the metallurgist is likely to encounter when he tries to recover in the blast furnace the metal from old chromite lining used as a refractory material in the copper reverberatory furnace. It appears that chromite cannot be fluxed at temperatures which usually prevail in copper blast furnaces. This calls to mind the freezing-point curve drawn by M. Simonis1 of mixtures of chromite and kaolinite. The chromite used in the experiments contained 52.9 per cent. Cr203, 22.6 FeO, 4.8 AI203, 9.6 Si02, .10.1-MgO; FIG. 1. the kaolinite was clay from Zettlitz with 98.5 per cent. clay-substance: The accompanying curve shows that the eutectic mixture with 35 per cent. kaolinite and 65 per cent. chromite freezes at Seger cone No. 15 (1435° C.), while kaolinite fuses at cone No. 35 (1770° C.) and chromite at cone No. 42 (2000° C.). The curve indicates that the difficulty in the blast furnace can be overcome by having at the smelting zone a temperature much higher than is usual in copper smelting; a charge composition similar to that prevailing at the Mansfeld copper smeltery -which gives with 23 per cent. coke a, slag of the composition Si02, .49.09; .(FeMg)0, 5.58; (CaMg)0, 16.02; A1203,-16.02-might flux and fuse chromite.

Jan 3, 1918

By M. Kitada, U. Kawabe, F. Ishida, T. Doi

The relations between micros tructures and critical current density in transverse magnetic field were experimentally investigated due to each transformation of the 0 to 0' + P" phases at 700' C for superconductmainly examined using replication electron microscopy. The ß' or a precipitates were found to pin down magnetic flux lines in these alloys. The effects of precipitation upon the critical current density were discussed in relation with the size, spacing, and characler of these precipitates. HIGH magnetic field superconductors, such as Nb-Zr, Nb-Ti, and Nb-Zr-Ti alloys, have been recently put to extensive practical use as winding materials for superconducting magnets.13 The critical current density of these hard superconductors under an applied magnetic field is an important characteristic for magnet materials and is very sensitive to metallurgical structure. It is generally known that the critical current density is increased by introducing dislocations and precipitates into a superconductor; that is, dislocations and precipitates are presumed to be barriers that hinder quantized flux lines from moving.4'5 Theoretical6'7 and experimental analyses of the motion of flux lines and the interaction between flux lines and various defects have already been reported by many authors. Metallographic analysis of high magnetic field superconductors such as Nb-Zr and Nb-Ti is difficult, so that no quantitative relationship between microstruc-ture and critical current density has been established yet. In this paper, the effect of precipitation on the critical current density in magnetic field was investigated for two superconducting alloys, Nb-40Zr-10Ti and Nb-5Zr-60Ti. In these alloys the resistive critical field H, at 4.2oK was about 100 kG and the critical current density Jc at 80 kG was of the order of 104 amp per sq cm.13-l5 The superconducting properties were examined in relation to the microstructural changes due to transformation of i) the ß to ß' + ß" phases at 700°C for Nb-40Zr-10Ti alloy and ii) the ß to a + ß phases at 500°C for Nb-5Zr-6OTi alloy. The effect of size, spacing, and character of precipitates on flux line pinning was in particular examined. The microstructures were studied by means of residual resistivity, microhardness, and tensile strength measurements as well as by X-ray diffraction, optical, and replication electron microscopies. I) EXPERIMENTAL PROCEDURE Pure niobium, zirconium, and titanium, in the form of rods 0.8 cm in diam, served as raw materials. Results of chemical analyses of these rods are given in Table I. Ingots of the alloys, 0.4 cm in diam and 3 cm in length, were prepared by means of levitation melting, utilizing a copper mold in an argon-gas atmosphere. Samples from the ingot then were cold-worked by grooved mill to 0.2 cm in diam, heat-treated homogeneously (in the ß phase region) for 5 hr at 1100° in a vacuum of 1 x 106 Torr, and finally cold-drawn to 0.025 cm in diam. For heat treatments, samples were wrapped in niobium foil and sealed in an argon-gas atmosphere in fused quartz capsules. Water quenching was done after each heat treatment. Subsequently H-J, were performed at 4.2° by slowly transporting the current through the samples 4 cm long, under transverse magnetic field, until the least detectable resistive terminal voltage was observed. The resistive critical field H, was taken as the field at which 100 pv appeared at 4.2°K across a sample 3 cm in length, with a current of 5 ma. The critical temperature T, was measured by means of a conventional four-probe resistivity technique and taken as the temperature at which the sample resistance reached one-half of full restoration of the normal-state resistance with a current l ma flowing through a sample 2 cm in length. Precipitates were observed by means of optical microscopy and carbon replication electron microscopy. The etching solution consisted of 5 ml HF, 10 ml H2SO4 10 ml H2O2, and 50 ml H2O, and shadowed carbon replicas were examined in a itachi HU-11 electron microscope operated at 50 kv. X-ray diffraction photographs were taken by a 11.46-cm-diam Debye-Scher-rer camera using copper Ka radiation. The micro-hardness was measured under a load of 200 g using

Jan 1, 1969

By J. H. Anderson, G. A. Parks, B. K. Jindal

Both temperature and humidity are important variables in electrical separations. By independent control of temperature and water vapor pressure, it is shown that charge depends primarily upon relative humidity, not on temperature or water pressure alone. All the effects of temperature changes other than modification of humidity are apparently small. However, humidity control can be achieved through manipulation of the more tractable variable, temperature. Both temperature and humidity are important variables in electrical separations. Some of their effects have been described in general by Fraas1,2 and by Ralston.3 The influence of temperature and humidity may be considered a problem in industrial separations because humidity, especially, is not normally controlled, hence leads to unpredicted quality control problems. The problem is significant whether the separation is based on conductivity differences or on contact electrification. There is no doubt that water adsorbs from humid atmospheres onto mineral surfaces resulting in conductivity changes.'-8 An empirical relationship between conductivity and humidity is1.4-6,8 where a and b are constants peculiar to the substrate, and s and h are the conductivity and relative humidity respectively. Some authors have taken advantage of differences in a and b among minerals to make or propose electrodynamic separations in which h is the key control variable. Fraasl,2 reported that the charge developed on quartz and feldspar through contact with aluminum is sensitive to humidity, as illustrated schematically in Fig. 1. Lawver9 found that the charge developed by quartz on contact with several materials was tem-

Jan 1, 1967

By Walter C. Smith, O. J. Seeds

METALLIC bismuth was known in the Middle Ages and the name is supposed to come from the German Wismut. The origin of the German name is uncertain. References to bismuth are found in the writings of Valentine, Paracelsus, and Agricola between 1450 and 1550. Early specimens of bismuth were very impure and often were confused with antimony, tin, and zinc. About the middle of the eighteenth century, J. H. Pott, C. J. Geoffroy, and Torbern Bergman succeeded in producing fairly pure bismuth and showed it to be an elementary metal similar in many respects to lead. H. S. Washington has estimated that bismuth occurs in the earth's crust about as abundantly as tungsten and silver; i.e., to the extent of 10-6 or 10-7 pct. It is found as native metal, both alone and associated with tin, copper, and other metals, and in a large variety of ores. The important ores are the sulfide (bismuthinite), the oxide (bismite), and the carbonates (bismutite and bismutosphaerite) . Other occurrences of bismuth are in the vanadate (pucherite), the selenide (guanajuatite), the telluride (tetradymite), and in many complex sulfides, arsenides, and antimonides. Bismuth minerals have been found in many parts of the world but very few of the bismuth deposits have been of economic value, the oxide ores from parts of China being the exception. The major portion of the bismuth production of today is the so-called by- product bismuth. Bismuth often occurs in ores mined and treated primarily for other metals, and during the treatment of these ores

Jan 1, 1953

By A. Singh, W. M. Fleming, J. J. Santana, A. E. Torma

The present study investigated the extraction of uranium from a low-grade ore by sulfuric acid and the removal of radium from the leach residues by brine solutions. The optimum leaching conditions were found to be 1.5 mole [£]-1 H2SO4, 6.Og[9]-1NaClO3, 75°C,50% pulp density and 750 rpm with respect to the rate of uranium extraction. The maximum theoretical attainable rate of uranium extraction was determined to be V = 1.09 x 10 -2 mole [¢]-1h-1 with respect to pulp density. The order of reaction was found to be zero regarding the effect of sodium chlorate concentrations. The apparent activation energy of uranium extraction was calculated from the Arrhenius plot to be [A]E a - 2.36 kcal mole-1 (9.87 kJ mole-1). Based on a statistical design, an empirical equation has been developed describing the rate of uranium extraction with the leaching parameters. This equation can be used to generate data which may be useful for scaling up the process to pilot plant level. The most efficient brine solution for the extraction of radium - 226 from the leach residue was found to contain one mole[f] -1 CaCl2 and 0.01 mole [2] -1 HC1. The two step leaching with this solution resulted 87% removal of radium from the leach residue. On the basis of this study, a flow-sheet has been proposed for the extraction of uranium and radionuclides from the ore and leach residue to yield almost innocuous tailings.

Jan 1, 1982

By Charles Y. Clayton

A study of the literature shows that the greater part of research work on annealing of cold-worked iron has been for the purpose of studying the effect on grain-size and properties other than hardness. No reference has been found of experimental work of the same nature as that explained in this short paper. The material used throughout was Vismera iron, an iron containing 0.03 carbon and made several years ago by the Inland Steel Co. One-half inch stock was cut into cylinders % in. long. The cylinders were then compressed for 60 sec. in a Reihle testing machine under loads as indicated below: CoMPressiON, Average Length, Series Pounds Inches 1 10,000 0.693 2 15,000 .599 3 20,000 .501 4 25,000 .426 5 30,000 .378 6 35,000 .351 7 40,000 .311 Fig. 1 shows these cylinders after compression. Each series consisted of 17 specimens lettered 0, B, C, D, E, F, G, H, I, J, K, L, M, N, P, Q and R. One specimen of each series was reserved for study of the properties in the cold-worked condition. The other specimens were annealed in a Hump furnace for 1/2 hr. at the following temperatures: TEmpeRa- TempeRa- Letters tuRe,° C. LettERs tuRe °C. B............................... 250 J.............................. 650 C............................... 300 K............................. 700 D............................... 350 L.............................. 750 E............................... 400 M............................. 800 F................................ 450 N............................. 851 G............................... 500 0. . :........................... 900 H............................... 550 P.............................. 950 I................................ 600 Q............................. L000

Jan 1, 1926

By G. J. Borbely, E. A. Devuyst, V. A. Ettel

Introduction Of the techniques reported for cyanide removal from effluents, alkaline chlorination is the most common (Fisher and Wasser, 1969; Reidt, 1969). Shortcomings with this technique are the high reagent costs, chlorine contamination, and potential formation of cyanogen chloride. Chemical oxidation methods are also not suitable to remove cyanide from effluents containing sulphides in suspension, such as flotation tailings. An inexpensive method for removing cyanide, combined cyanide and related species from waste waters has been developed in Inco laboratories. The method is based on the use of sulfur dioxide (or a sulfite), lime, and air as the reagents. The decomposition reactions of cyanide, combined cyanide, and related species are catalyzed by copper in solution. Complete removal of cyanide species, most of which are oxidized to cyanate, is obtained by treating copper containing cyanide effluents with sulfur dioxide-air mistures while maintaining the pH between 6 and 10 with addition of lime. The new approach can also be applied to selective destruction of cyanide and combined cyanide in effluents containing sulphides in suspension, such as pyrrhotite. Again, a sufficient amount of dissolved copper must be present or added. Metals and precious metals present in the effluents are recovered as hydroxides by adjusting the pH of the treated effluents to about 9-10. Using the new method, the anionic species are removed in the following order: Free CN- > Complex CN- > Thiocyanate The above removal sequence is unusual as oxidants such as chlorine and ozone oxidize thiocyanate preferentially over the combined cyanide.

Jan 1, 1985

By R. N. Orava

TO the author's knowledge, only one satisfactory high-resolution technique for etch-pitting dislocations in Cu-Zn alloys has been published.' In that account, pits in 70/30 brass single crystals were produced by etching electrolytic ally in a 30 pct orthophosphoric acid bath. Thereafter, observations were made from surface replicas by electron microscopy. The method of pitting and observation permitted the high resolution necessary for the distinction of individual dislocations in arrays of pile-ups. However, no comment was offered concerning the possibility of obtaining pits which are amenable to optical resolution. Moreover, for adequate results, the electrolytic pitting process is invariably preceded by a polishing stage which could obscure the surface features of interest. Consequently, it would be desirable to be able to delineate, by solely chemical means, dislocations which could be detected by both optical and electron metallo-graphic techniques. This was achieved by the simple expedient of modifying two etchants reported by young2 to reveal dislocations on the (100) planes of pure copper. Single crystals of 70/30 a brass, described previously,3 were sectioned to provide a surface parallel to a set of {100) planes, mechanically polished, and subsequently electropolished at 2.4 v in a solution comprised of 2 parts H3PO4, 4 parts ethanol, and 3 parts water. The inclusion of ethanol tended to inhibit nonuniform surface attack. Etch-pitting was effected by a 2 to 3 sec immersion in a 70 pct aqueous solution of HNO3. The samples were then washed in a fast-flowing stream of water, and rinsed further in distilled water, and ethanol, before drying. It is important to note that this reagent should be either used immediately after mixing, or, if allowed to cool, reheated to about 35°C prior to use. No pitting was obtained at room temperature. Typical results are shown in Fig. 1 where (a) is an optical view of the pitted surface and (b) is an electron micrograph of a silicon monoxide replica shadowed with tungsten oxide. The former is characteristic of a somewhat longer etching time (-6 to 8 sec) which varied with bath temperature. Similar pits accrued from a 1/10 aqueous dilution of another of Young's solutions2—2 M FeC1,6H20 and 7.8 M HBr.

Jan 1, 1968

By Harold R. Bradford

EXPANSION initiated during and after the war has placed industrial plants in new areas and increased reduction and manufacturing facilities in communities already established. With added expansion interest has grown in possible area contamination from waste products. Evolved flue waste contains many chemical contaminants that may or may not cause concern; however, atmospheric pollution has always been a problem to industrial communities. For some time effects attributed to small quantities of compounds of fluorine in various waste gases have been studied by industrial, medical, agricultural, and associated interests.1'2 Aside from an article by Churchill, Rowley, and Martin in 1948," little has been published on the subject of fluorine in coal except by foreign investigators. The first indication of fluorine compounds in coal was noted in England in 1934 by R. Lessing,4,5 who found that the presence of fluorine in Midland and West County coals was definitely established by etching of glass and by severe corrosion of porcelain fillings in a gas works scrubber. Etching of glass in a direct contact annealing kiln initiated research, and in 1944 four papers were published by H. E. Crossley,6-9 giving results of investigations of fluorine in coal of England by the Fuel Research Board, Department of Scientific and Industrial Research. These investigations studied methods of determining fluorine, the quantities present in various coal deposits, the geographical distribution of fluorine in British coals, occurrence of fluorine in minerals associated with coal, amounts of fluorine compared to other constituents of coal, the nature of fluorine compounds, and industrial significance of fluorine in coal. It was shown that British coals contain from 5 to 200 ppm of fluorine, which is probably present as fluorapatite [Ca10F2(PO4)6], often written as [3Ca3P2O8.CaF2]. The fluorapatite is intimately associated with shale in some coals and can often be separated from these coals along with the shales. H. E. Crossley8 also reported no correlation between the amounts of chlorine, sulfur, or ash and the amount of fluorine in different coals. He found, however, a relationship between the content of fluorine and phosporus in many British coals. Thus it should be possible to anticipate likely fluorine-rich coals from existing data giving phosphorus content. Behavior of the fluorine compounds of coal was compared with that of 12 fluoride-phosphate minerals in sink-float separations and solvent ex-

Jan 1, 1958

By Ming-Kao Yen

A considerable amount of work has been reported in the literature in regard to the texture and earing behavior of copper strip. The rolling texture of copper has been confirmed as (110) [112] and (112) [111], which yields ears of a drawn cup at the position 45" from the rolling direction.1-3 The recrystallization texture has been established as the cubic or (100) [001] texture, where the earing positions are at 0" and 90" to the rolling direction.4-8 It has also been reported that in the development of cubically aligned grains of copper strips, the percentage of this cubic texture increased with an increase of final reduction and final annealing temperature.8,9 A comprehensive study on H.C. copper (British commercial copper of high-conductivity quality = Cu 99.95 pct, O2 0.03 pct, Ag 0.003 pct, Fe 0.005 pct and Pb < 0.001 pct) was made by Cook and Richards.6 They concluded that the recrystallization textures could be described as one or more of the following textures: (1) a single texture (100) 10011, (2) a twin texture (110) [112] and (3) a random orientation, depending upon the previous history of the specimen concerned. The effect of various alloying additions in copper was reported by Dahl and Pawlek.10 They found that certain alloying additions, such as 5 pct Zn, 1 pct Sn, 4 pct Al, 0.5 pct Be, 0.5 pct Cd, or 0.05 pct P suppressed the formation of cubic texture. Brick, Martin and Angierll reported that the cold rolled textures due to various additions fitted a rather simple pattern. However, the recrystallization textures were subject to very considerable variations. In the discussion of this paper, Baldwin stated that deoxidized copper containing 0.02 pct P gave a complicated recrystallization texture at lower temperature. When this copper was annealed at high temperature, a single texture appeared which was described as (110) [ill] but. according to a pri- vate communication from Baldwin, this orientation reported was in error and should have been reported as (110)[112]. He also reported that the earing positions of drawn cups were at 60" to the rolling direction.12 Recently, Howald, in his discussion on the paper by Hibbard and Yen,13 reported that the rolling texture of phosphorus deoxidized copper, containing from 0.006 to 0.020 pct phosphorus, was of the pure copper type. When these coppers were annealed at lower temperatures, they exhibited a random orientation, and when they were annealed at higher temperatures they had a mixed (111)[110] and (100)[001] texture, depending on the severity of the final reduction and annealing temperature. However, the specific influence of phosphorus and other impurities on the recrystallization textures and the deep drawing properties of copper strip has not been thoroughly reported. Therefore, an attempt has been made in the present work to determine the rolling and recrystallization textures and also the earing behavior of five types of commercial copper and thereby to evaluate the effect of phosphorus and some other significant impurities on the development of texture for cold reductions of about 87 to 89 pct. Materials Used The five types of copper employed in the present investigation were two phosphorus deoxidized coppers of different phosphorus content (0.007 and 0.013 pct P), an oxygen-free copper (OFHC), an electrolytic tough-pitch copper, and a fire-refined tough-pitch copper. These materials were subjected to a thorough spectroscopic and chemical analysis. The designations and the chemical compositions were as shown in Table 1. The coppers, FA1, FA2 and FA3. were hot-forged from 3-in. billets into a ½ X 6-in. plate and cold rolled to the ready-to-finish gauge indicated below. FA4 and FA5 were hot rolled and scalped to ready-to-finish gauge. The grain size of all the materials in the ready-to-finish condition was about 0.030 to 0.045 mm. Table 2 shows the last stage of the production schedule for each copper strip used. Experimental Procedure ANNEALING, GRAIN SIZE AND HARDNESS DETERMINATIONS Specimens of each type of copper were finally annealed in air for periods of one hour at temperatures ranging from 300 to 1600°F and were subsequently cooled in air. The average grain diameter of the annealed specimen was estimated by comparing with a standard grain size chart. Hardness was determined on the Rockwell 15 T scale. CUPPING TESTS Cups were made in a blanking and drawing set, in which blanks of 2-in. diam were drawn to a cup of 1.25-in. diam with an average depth of about 0.75 in. The clearance between the punch and die was about 0.032 in. The ears of the cup were measured with a special fixture which read the height of ears to one-thousandth of an inch on every ten-degree interval along the circumference of the cup. POLE FIGURES The usual transmission diffraction method with unfiltered copper radiation was employed to determine the pole-figures of the specimens cold-rolled or annealed at 900°F. All the pole-figures were derived from the positions of intensity maxima on 111 diffraction rings of the X ray photo-grams taken at 10 rotation of a

Jan 1, 1950

Jan 1, 1968

Jan 1, 1966

By R. I. Jaffee, F. C. Holden, H. R. Ogden

ECENT papers dealing with the properties of unalloyed iodide titanium have been directed primarily at the determination of base-line properties for alloy investigations. Early work was limited to a few tests because of the limited availability of iodide titanium at the time. In the results of papers by Campbell et al.,1 Gonser and Litton,2 Jaffee and Campbell,3 inlay and Snyder,4 and Jaffee, Ogden, and Maykuth, data on mechanical properties are presented for unalloyed iodide titanium in the annealed and cold-worked conditions. Data are presented in this paper which show the effects of heat treatment on the structure and mechanical properties of commercially produced iodide titanium. Correlation is made between microstruc-tural variables and the mechanical properties. Experimental Procedures Melting Stock: The melting stock used was as-deposited iodide titanium, produced by New Jersey Zinc Co. The furnished analysis showed the following range of impurities: N, 0.004 to 0.008 pct; Mn, 0.005 to 0.013; Fe, 0.0035 to 0.025; Al, 0.013 to 0.015; Mo, 0.0015; Pb, 0.0045 to 0.0065; Cu, 0.0015 to 0.002; Sn, 0.001 to 0.01; Mg, 0.0015 to 0.002; and Ni, 0.003. Hydrogen content as determined by vacuum-fusion analysis was 0.0091 wt pct (0.44 atomic pct) after arc melting and fabrication. Nitrogen analysis on the arc-melted and fabricated titanium showed a content of less than 0.002 pct N. The average hardness of the furnished stock was Rf 70, or approximately 85 VHN. Melting Procedure: The as-deposited rods were rolled, sheared, and degreased in preparation for arc melting. The charge was arc-melted with a tungsten electrode in a water-cooled copper crucible under a positive pressure of high purity (99.96 pct) argon. The final ingot was approximately 2 in. in diameter and showed no increase in hardness over that of the initial stock. Fabrication: Heating for fabrication was done in air. It was begun by forging the ingot into a 3/4 in. diam rod, at an initial temperature of 1600°F. Scale was removed by sandblasting. The rod was then swaged to 1/4 in. diam at room temperature through a series of 20 dies, with approximately 10 pct reduction in area between each die. An anneal of 1 hr at 850 °C in air was given after the 1/2 in. die, such that the final cold reduction was 75 pct. Sections cut from this rod were used for test and microstructure specimens. Heat Treatment: Heat treatments were carried out in resistance tube furnaces with stainless-steel linings, under an atmosphere of gettered argon. As further protection against contamination, the specimens were packed in titanium turnings in a titanium sleeve. Control experiments have shown negligible hardness increases with this method, indicating that contamination from oxygen and nitrogen is slight. Three cooling rates were employed in this work; these have been designated as water quenching, argon cooling (to simulate air cooling under a controlled atmosphere), and furnace cooling. The cooling rate for an argon cool is 100°C per min for the first minute, with an average cooling rate of 35°C per min over a 15-min period. A furnace cool requires about 10 hr, with an average cooling rate of 3.6oC per min during the first hour, and an average cooling rate of 1.2°C per min over the 10-hr period. Microimpact Test: The specimen adopted was based on the cylindrical Izod Type Y specimen (ASTM, E23-41T). All dimensions were reduced to half scale, including the notch radius. Specifications are shown in Fig. 1. The specimen is held vertically in an adapter and broken as a cantilever beam. Impact tests were run on a constant-velocity (11.34 ft per sec) Tinius Olsen impact testing machine with a total available energy of 100 in.-lb. Tests were made to determine the correlation between this microimpact and the standard V-notch Charpy impact test. Curves showing impact energy as a function of temperature for both impact tests are plotted in Fig. 2. Transition temperatures, when they occur, are about the same for both impact tests. All three titanium-rich materials have the same conversion factor, 10. Tensile Testing: Tensile tests were conducted on Baldwin-Southwark testing machines using the 600, 2400, or 3000 1b range. Specifications for the test specimen were taken from the 1948 edition of the ASM Metals Handbook, and are shown in Fig. 1. Strain measurements were made using an SR-4 resistance gage (Type A-7) cemented to the reduced section in conjunction with a lever-type extenso-meter. Readings on the SR-4 strain indicator were

Jan 1, 1954

By Carl Scholz

Discussion of the paper of Carl Scholz, published in Bi-monthly Bulletin, No. 22, July, 1908, pp. 551 to 559. HOWARD N. EAVENSON, Gary, W. Va. (communication to the Secretary*) :-For some time before the publication of Mr. Scholz&apos;s paper, I had been collecting data bearing upon its subject, and I now take pleasure in presenting my results to the Institute in the form of a discussion. It has long been a matter of common opinion among mining-men that mice-explosions are, more frequent during the colder, or winter months, than during the warmer ones, and it is a matter of common knowledge among them that the air-ways and road-ways in most mines are much drier and are more in¬clined to be dusty during the winter than during the summer. In many mines, places which are wet and sloppy in the summer are dry and sometimes dusty during the winter. These changes, of course, can only be due to atmospheric conditions, and are caused by differences in temperature and humidity. Until recently, however, very little attention has been paid to the part that atmospheric conditions may play in mine-explosions, or, rather, to the effect they may have in rendering mine-conditions peculiarly dangerous, and in spreading and rendering more disastrous the effects of what would otherwise probably have been .small explosions. To show the difference in mine-conditions during sunnier .and winter months, I have tabulated in Table I. the results of 24 observations of hygrometric conditions in several different mines at different times of the year. Mines Nos. 1, 2, and 6 are located in the Pocahontas.coal -region, in McDowell couuty, W.Va., the first one being a shaft-mine shaft mine and the others drift. Mines 1A and 2A are drift-mines located in Logan county, W. Va. All of these are mines of fair size, but none of them has been in operation more than six years,

Jun 1, 1909

By K. L. Komarek, P. F. J. Landler

Synthetic polycrystals of wustite were reduced ilz H2-H2O mixtures over limited roncentration ranges wiltun the wustite. field and the weight changes were continuously followed with a McBain quartz spiral balance. The reduction was. found to be controlled by a combined surface plus solid-state diffusion reaction. The solid-state diffusion had an activation energy of 38 kcal. Self--diflusioities of iron decreased with itzcreasing vacancy concentration. The activation energy of. the surface reaction runs different tor- different samples. The surface reaction-rate constan increased with increasirzg vacancy concentration. THE reduction of the oxides of iron has been studied for many years. Edstroem&apos; has summarized the early work and has provided much information on the reduction of magnetite and hematite by hydrogen and carbon monoxide. More recent summaries are those by smeltzer2 and Themelis and Gauvin.3 Most investigators have reported that the iron metal which forms the outer layer during gaseous reduction is rather porous. According to Kohl and Engel14 the formation of such a porous iron layer depends on the properties of the underlying wiistite layer, on the reaction of the gas with the wustite surface, and on the transport of matter through the wustite layer. McKewan, Quets, Wadsworth, and Lewis, and Knacke 10 have found that, if a porous iron layer is formed, a surface reaction between gas and wustite at the bottom of the pores controls the rate of reaction. Seth and ROSS 11 and Warner 12 have pointed out that the influence of the gaseous pore diffusion through the porous iron layer cannot be neglected. It has further been shown that the wiistite layer formed during reduction is dense and that transport of matter across the layer occurs only by solid-state diffusion of iron ions.13,14 The solid-state diffusion rates observed by Edstroem and Bitsianis 14 and the surface reaction rates observed by Quets eta1.&apos; show that an interaction of the two steps in controlling the reaction rate has to be considered. In this investigation the reduction of wustite was studied with respect to the interaction of the two steps, isolated from any other effects, by reducing wustite within the wustite field from higher to lower oxygen concentrations with H2-H2O gas mixtures. A similar study with CO-CO2 mixtures has been performed by Levin and wagner.15 Fused synthetic wustite polycrystals were reduced in steps of 0.4 wt pct from 24.4 to 23.2 wt pct 0 and over a temperature range from 700" to 1050°C. A few tests were also conducted with reduction steps from 24.4 to 23.6 wt pct 0 and 24.5 to 23.2 wtpct0. The Fe-O phase diagram is shown in Fig. 1 where the composition of the gas phase in equilibrium with the condensed phases is plotted as pct H2 vs the temperature. A careful study of the literature led to the conclusion that the fully drawn equicomposition curves (in wt pct O) in the wustite field used by Edstroem 1,16 and other authors needed some correction. Based on results by Darken and Gurry17 (shown as open circles) and on some of our own data, four corrected curves for 23.2, 23.6, 24.0, and 24.4 wt pct O were calculated (drawn as dashed lines in Fig. 1) which should replace the fully drawn equicomposition curves. MATERIALS AND APPARATUS Materials and Specimen Preparation. Wustite was prepared from iron sulfate (Fisher Scientific Co., New York) which had a purity of over 99.92 pct, with small amounts of manganese, copper, and zinc adding up to 0.03 pct. From the aqueous solution iron oxalate was precipitated and decomposed to magnetite according to Economos. 18 The magnetite powder was pressed into cylinders and sintered in vacuum at 900°C for several hours. The sintered compacts were placed in a platinum crucible of 2.5 cm diam which was fitted into a high-purity alumina crucible and then inserted into the center of the graphite heating element of an electric resistance furnace.lg The furnace was evacuated to below 1 p Hg and the magnetite sample was slowly heated. The evolution of gases during heating deter-

Jan 1, 1967

By R. L. McCarron, G. R. Belton

The diffusivities of oxygen and sulfur in liquid iron have heen determined hy a capillary technique in which the surface concentrations of the solutes were established by means of appropriate H2/H2 and H2S/H, gas mixtures. Total diffusate and concentration profile results are shown to be in good accord, yielding for- 1560 and Supporting results at 1660°C are also presented. The conditions necessary to avoid gas transport control in this type of experiment are discussed. IN spite of their importance in understanding the kinetics and mechanisms of refining reactions, the dif-fusivities of oxygen and sulfur in liquid iron are not well established. Accordingly, as a first step in studies of rates of solute absorption from the gas phase into liquid iron, new measurements of these diffusivities have been made and are presented in this paper. The only published results for the diffusion of sulfur in pure liquid iron are those of Kawai.&apos; He used a diffusion couple technique in which two cylindrical specimens, one containing sulfur and the other with negligible sulfur concentration, were joined together and held in a refractory capillary. After an experiment, the sample was quenched and the concentration distribution of the solute determined. Kawai recognized that significant changes in solute distribution occurred during melting and freezing and he attempted to correct the concentration profiles for these effects to give a sulfur diffusivity of 4.6 x 10-6 sq cm per sec at 1560°C. The method of correction, however, was not rigorous and the uncertainty in this result cannot be easily assessed. Koslov et a1.2 have reported the diffusivity of oxygen in iron as 7.8 x 10"3 sq cm per sec at 1660°C. This value appears to be unreasonably high but, unfortunately, details of their experiments are not available. Shurygin and Kryuk have used the rotating disc method for a study of oxygen diffusion in liquid iron. In their experiments a silica disc was rotated in liquid iron containing oxygen, and the rate of formation of liquid iron silicate was determined by measuring the decrease in weight of the disc. On the assumption that the rate of dissolution was controlled by the diffusion of oxygen in the iron, the diffusion coefficient was computed to be 5.2 x sq cm per sec at 1550°C. However, the Levich equation, which was used to interpret the rate data, was originally de- rived for the case of mass transfer between a solid disc and a single-phase liquid. The hydrodynamic and diffusion boundary layers in the iron stirred by a disc, via coupling of the silicate melt, may be appreciably different from those predicted by Levich&apos;s equations. Recently, Novokhatskiy and Ershov, using an identical experimental method to that of Shurygin and Kryuk, obtained a diffusivity for oxygen in liquid iron of 1.22 x 104 sq cm per sec at 1550°C: no reasons were offered for the disagreement. Schwerdtfeger5 has also recently studied the diffusivity of oxygen in liquid iron. He reacted shallow melts of liquid iron, 0.5 to 1.0 cm deep and contained in high-purity alumina crucibles, with appropriate H20-HZ-He mixtures. The total sample was analyzed, without sectioning, to obtain the average concentration of diffusate. A value at 1610°C of D = 12(3) x 10-5 sq cm per sec was obtained from the results of twenty experiments.= Oxygen profile measurements, which were carried out in three additional experiments using long capillaries and the semiinfinite boundary conditions, indicated a diffusivity about half that computed from the shallow bath experiments. Possible sources of error in Schwerdtfeger&apos;s study will be discussed later in this paper. EXPERIMENTAL TECHNIQUE The essential arrangement of the diffusion cell is shown in Fig. 1. The liquid iron was contained in an alumina capillary, 3 to 4 mm diam and 3 to 9 cm long, which was supported by a hollow alumina pedestal and this whole assembly was held within a movable alumina reaction tube. This tube, which was about 7 mm in bore

Jan 1, 1970

By W. A. Wall, R. L. Kidd

IN present-day flotation practice, grinding of the flotation feed is carried to extremely fine sizes, 70 to 80 per cent minus 200 mesh being customary. The greatest flotation losses occur in the coarsest and finest sizes, but the losses in the very fine sizes are, of course, much the more important because of the large proportion of fines in the feed. These losses are particularly high in zinc ores so a study of the effect of size on the flotation of sphalerite has been made. The mineral used in these experi¬ments was a pure sphalerite, especially free from copper, from the Joplin district in Missouri. The sizes coarser than 200 mesh were separated by screening, the sized mineral then being deslimed on a Wilfley table. The sizes finer than 200 mesh were obtained by water elutriation as described by H. R. Bradford (M. S. Thesis, University of Utah, 1932) ; particles finer than 6.5 microns could not be obtained with the apparatus used.

Jan 1, 1933

[A Aalseth, Earl P. (M 51) Geol, Amerada Petr. Corp., Box 1498, Billings, Mont. Abadie, Henry G. (M 43) Asst to Supvr of Oper, Long Beach Oil Dev. Co., 255 S. Santa Clara, Long Beach 7, Calif. Abbe, T. Waldo (A 56) Ass&apos;t Dist Oper Supt, Sun Oil Co., Beaumont, Tex. Abbott, J. L. (M 56) Partner, Pritchard & Abbott, 501, Century Bldg, Fort Worth, Tex. Abbott, Richard H. (J 51) Owner, Abbott & Howard, 422 W. Hermosa, San Antonio, Tex. Abbott, Seth J., Jr. (M 51) Tekoil Corp., .2;A6 Mercantile Nat&apos;l. Bank. Dallas, Tex. Abbott,. William G. (M 50) Div Mgr, Rice Eng. & Op. Inc., Box 1142, Hobbs, N. M. Abderhalden, R. R. (J,59) Box 100, Carmi, Ill. Abel, Malcolm D., Gen Mgr, Bakke Oil Co., Midland, Tex. Abel, Raymond L. (M 28) Prof of Chem Engr, Univ. of Pittsburgh, Pittsburgh 13, Pa. Abel, Wayne K. (M 57) 1513 Patton Drive, Odessa, Tex.]

Jan 1, 1961