Search Documents

By T. R. Schermerhorn, Samuel L. Hoyt

The hardness of annealed copper has been given in the literature and is easily obtained by any of the standard methods of hardness testing. It is not our intention to correct published values or to add to them, but to describe tests of two bars of annealed electrolytic copper in which the methods of Meyer's analysis were employed. Meyer's Analysis of Ball Indentation Test The ball indentation test is probably the most valuable hardness test we now have but, as it is carried out in the Brinell or Rockwell test, the result may be seriously in error without the operator suspecting such to be the case. This condition results from the isolated and uncontrolled nature of the measurement. The accuracy depends on the accuracy of the equipment and the care and skill used in the operations; there is nothing in the impression diameter, which is all that is measured, to indicate the presence of error. Meyer's analysis supplies a control of the measurements that goes far toward eliminating unsuspected errors. The principles of this work may be obtained from elsewhere.' As this subject has not received the attention of this Institute, it may be well to summarize the more important points as follows. The chief difference between the usual ball indentation hardness test and Meyer's test is the use of a number of loads, instead of one, covering the range from small to large loads. The reason for this may not be obvious; the resistance to penetration may, and generally does, vary with the penetration of the ball; consequently a single determination can give only the resistance at that particular load. At some other load, the resistance may be quite different. For example, a test on annealed copper at 250 kg. gave a resistance to penetration of 39.5 kg. per sq. mm., while a similar test at 3000 kg. gave a resistance of 56.8 kg. per sq. mm. For the purpose of finding some figure that might be used to represent the hardness of the sample of copper, there is no reason for selecting one of

Jan 1, 1926

By Arthur B. Cummins

POWDERED nonmetallic minerals and rocks of many different types are used extensively in industry for incorporation in compositions and manufactured products The term "mineral filler" is commonly employed to designate a material that is used for a specific purpose but not as an essential or reactive component Such a definition is not without objections, and it is indeed difficult to define fillers in any fully satisfactory manner, since the term has come to have so many different meanings and to cover such a wide range of uses. A filler is defined, for the purposes of this chapter, as a substantially inert material not specifically employed as a reactive or essential component, the primary function of which is to modify the properties or processing of a composition of matter or fabricated article Emery1 has emphasized that fillers change the properties of the product but are themselves unchanged in compounding or use The term "filler" appears to be rather general when referring to usages m bituminous compositions, rubber, composition floorings, fertilizers, plastics, textile finishes, and some others. In paper manufacture, in the paint industry and with insecticides, other terms are frequently employed, as is indicated, herinafter By placing emphasis on the function of the material used in modifying the properties of the composition or article, it is believed that a more useful classification of filler products and their applications may be derived. FUNCTIONS OF MINERAL FILLERS All of the manifold functions of mineral fillers cannot be listed in a summary review. A survey of the uses for these materials, however, shows that in nearly all cases the powders are employed to modify the properties of a composition of matter or those of a fabricated article, or to perform some useful function In the manufacture of either. A generalized list of these useful functions may be given is follows 1 To Modify Optical Properties Color Surface texture Opacity Brightness and gloss (as in paper and plastics) Flatness (as in lacquers and paints)

Jan 1, 1949

By C. C. McDermond

In reviewing petroleum development in Venezuela during the year 1936, it is well to bear in mind certain factors that affected progress, although not directly connected with the oil industry itself. At the start of the year, when the present Federal Administration took over the reins of government, reaction against the former regime resulted in some popular uprisings. Although these were entirely political in character, they were not without their effect on the oil industry itself. Such popular agitation really ended with a short general strike in Caracas, Maracaibo and other cities during June, these strikes being based on demands for certain changes in government policies. The strikes were duly investigated and their motives taken into consideration by the executive power or by Congress, and during the year many of the civil, political and administrative laws have been revised. In June and December, however, it was necessary to suspend activities in drilling and production work, particularly in the Lake Maracaibo Basin area. In June a strike caused a five-day shutdown in the main producing fields and on Dec. 14 labor difficulties resulted in a shutdown that continued to the end of the year, which necessitated suspension of all drilling and production in the Lake Basin area and curtailment of shipments to deep-water terminals. Actually, the strike lasted for a period of 42 days, until Federal intervention brought the dispute to a close with minor wage increases to workers hut with no loss of initiative or independence on the part of the oil companies. Operations in eastern Venezuela were not affected by the labor disturbances, production and exports having been reduced in December only in the Lake Basin fields. Well Completions On Jan. 1, 1937, a total of 3384 wells had been completed throughout Venezuelan fields, as compared with 3094 on Jan. 1,1936. Of these wells, 2005 were producers. The 290 completions effected during 1936 were by the following operating companies: Lago Petroleum Corporation, 123 completions; Dutch Shell group, 104; Standard Oil Company of Venezuela, 46; Mene Grande Oil Co., 15; British Controlled Oilfields, Ltd., 2.

Jan 1, 1937

By K. C. Gilbart, Edgar Stansfield

One of the most striking features of the coal series passing from peat through brown coal, lignite, etc., up to anthracite is the gradual reduction of moisture content with the increased coalification of the original plant material. Thus drained peat from a bog may contain 90 per cent water, brown coal contain 50 per cent, lignite 30 per cent, while a bituminous coal may contain only 1 per cent moisture. Moisture, therefore, is one of the important factors to be considered in coal classification, especially with the lower rank coals. With bituminous and higher rank coals the moisture content is less satisfactory for classification; it may even pass a minimum value and then increase with increasing rank to anthracite and superanthracite. Coal in an undisturbed seam contains moisture which is an integral part of the coal, but it may also be wet with free, underground water percolating through the seam. Only the former must be considered in evaluating the moisture content of the coal for classification purposes; this will be called the "true moisture" of the coal. When the seam is mined and sampled the sample taken may show the true moisture; on the contrary, it may contain in addition free mine water or, especially in dry, well ventilated mines, it may contain less than the true moisture. Coal contains unstable organic compounds which may decompose, with the production of moisture, when the coal is exposed to air at ordinary temperatures, or is heated with or without exposure to air. The potential moisture of a coal therefore is higher than its actual moisture. The lower the rank of the coal, the greater its instability, as a rule, and the greater the care necessary to avoid oxidation or decomposition in any investigation of moisture content. The majority of coal workers have preferred, on account of the difficulty in evaluating the true moisture of a coal, and for other reasons, to classify coals by analyses calculated to the dry-coal basis. A number of workers familiar with lower rank coals have recently insisted that the classification of such coals can be satisfactory only if analyses on the moist-coal basis are employed. The moisture-holding capacity of coal is therefore intimately connected with coal classification, and in this paper a procedure is outlined for determining the true moisture of a coal,

Jan 1, 1932

By Shiro Ban-ya, John Chipman

Using the same experimental method previously described, the activity of sulfur in a number of quaternary and more complex liquid iron alloys at 1550oC is determined. A "cross-product term zj.zk is determined for each of the quaternary alloys to take account of the mutual effects of the combinalion on the indi-vidual contributions to In 5 The interactiotl coefjicienls delermined for ternary solutions and cross-pvoducl coefficierlts from the quaternary systems are used to estimate the activity coefficient of sulfur in more complex alloys. OUR recent papers 1,2 have described new determinations of the activity of sulfur in Fe-S binary and Fe-S-j ternary solutions, but the practical applications of these data require the estimation of activity of sulfur in more complex systems. Previously, Sherman and chipman3 devised an approximate method for calculating the activity of sulfur in complex systems by summing the contributions to the logarithm of the activity coefficient of each element in the alloy. This procedure is more successful, as one of us has pointed out,4 when the concentration variable is taken as zs = ns/(nFe — nS t CLJ~ nj) rather than the conventional atom fraction x~ = nS/(nF, + nS + Enj). In the former definition, which is based on analogy to interstitial solutions, the value assigned to uj is normally +1 for metallic and -1 for nonmetallic elements." In addition, however, the effects of mutual interaction between alloying elements must be considered for the accurate estimation of the activity of sulfur in more complex systems. The purpose of this investigation has been to devise a more reliable method for estimating the activity coefficient of sulfur in nmIticomponent iron alloys. The measurements were carried out on some quaternary systems Fe-S-j-k for combinations of silicon, chromium, nickel, cobalt, molybdenum, and tungsten. Manganese was not included since the experimental method has been found unsatisfactory for volatile, sulfide-forming elements. The experimental method was the same in every detail as described previously. 1,2 The concentrations of sulfur, silicon, chromium, and copper in the quenched metals were determined by chemical analysis but those of nickel, cobalt, molybdenum, and tungsten were calculated from charged amounts. Iron sulfide was included in the charges in amounts estimated to furnish approximately the final sulfur content. CALCULATION W2 have shown2 that when zs and zj are the concentration variables in a ternary Fe-S-j solution the logarithm of the activity coefficient S = a~/zg is a linear function of the variables as and aj defined as follows:

Jan 1, 1970

By Charles Fulton

The study of the condensation of zinc from its vapor was undertaken to shed light on certain problems encountered in large-scale electric zinc-furnace work recently conducted. It is a matter of common knowledge that one of the disadvantages of the arc type, electric zinc furnace, is the production of a large amount of blue powder and proportionately little liquid spelter, for, as stated by Stansfield,1 "A notable defect in the electric smelting of zinc ores is the difficulty experienced in obtaining the distilled zinc in the liquid state; when zinc ores are smelted electrically, very little liquid metal is commonly obtained, nearly all of the zinc being in the state of powder."

Jan 8, 1918

By Christopher Haycocks, Michael Karmis, David G. Lundy

Roof bolting is the most common means of support in under- ground coal mines. The main advantages of this support system are the relative ease of installation and the ability to provide a stable and unobstructed work area. Roof bolts can be broadly classified into two categories, mechanical and resin bolts. Currently, about 20% of all bolts used are the resin types, and trends show an increasing popularity of these kinds. Although the reinforcing effects of resin bolts have been well demonstrated, there is, nevertheless, a considerable lack of knowledge of their interaction with the surrounding strata. To study this interaction and to further investigate the mechanisms involved in resin bolting, an instrumentation system was designed and tested in a southwestern Virginia coal mine. The instrumentation system was composed of straingaged resin bolts, convergence and differential sag stations, and a borescope. Strain gages mounted on the bolt determined axial, bending, and shear strain at several levels along the axis of the bolt. The roof movement, as measured by the convergence and differential sag readings and as observed by the borescope, correlated well with the strains registered on the bolts.

Jan 1, 1983

IT is necessary that all men who wish to bring things to a certain end should think of the agents needed to attain this. Now whichever one of the above processes you wish to use you must consider the nature of the material and see whether it is disposed to render what you wish to extract. Then you must see whether you have the other agents sufficiently powerful and proportioned to attain this result, for if the things were not in harmony your work would be vain and very laborious. Therefore, if you should wish to make waters or oils by way of distilla-

Jan 1, 1942

By A. J. Lynch, W. J. Whiten

Extensive research, ,development and plant application work has been done on automatic control systems for wet grinding and sulphide flotation circuits during the past twenty years. The result is that there is a good understanding of the process mechanisms, the effects which changes in different variables have on these processes, the procedure for design of control systems to satisfy particular objectives and the problems in the implementation of control systems. There is also an appreciation of the problems which are still to be solved. These are reviewed briefly in this paper. Other processes used for the beneficiation of fine particles have been studied in lesser detail. The control of dry grinding, coal flotation and gravity separation are mentioned briefly in this paper.

Jan 1, 1980

By John W. King, S. Ralph Austin

Spurred by recent forecasts of greatly increased demands for uranium by 1980 and beyond, interest is once again focusing on America's western uranium deposits. One of the principal producers in this area is the Gas Hills district in Wyoming, the site of approximately 12% of the known uranium in the U.S., including past production and current reserves. Located on the south flank of the Wind River Basin, the Gas Hills deposits have been recently studied by the Atomic Energy commission for clues to and guides for discovering similar-occurring ores. The ore deposits are confined to a permeable sandstone unit, up to 350 ft thick, at or near the base of the upper Wind River formation of early Eocene age. The uranium occurs in three principal north- south "ore trends," each of which is about six miles long, one mile wide, and separated from each other by approximately three miles (Fig. 1).

Jan 5, 1966

By T. E. Brower

SHORTLY after our previous paper on this subject was printed,1 we located a source of uncertainty in the results arising from the unexpected fact that hydrogen slowly reduces silica at 1100° C. in presence of iron, even when the iron nowhere touches the silica, although in absence of iron it does not do so. This difficulty has been completely obviated by the use of a small high-frequency furnace, which enables us to heat the specimen for analysis without raising the temperature of the silica vessel to a point at which any appreciable reduction of the silica glass occurs. We now describe this modification of procedure, and present some typical results obtained with it. For any given specimen of steel, the results are entirely definite and. reproducible, but their precise significance is still open to some question, as indeed is true of all methods of oxygen determination so far developed. Further elucidation of this question is to be expected from the cooperative comparison of the several methods now under way under the auspices of the Bureau of Standards at the instance of the Iron and Steel Division of the A.I.M.E.

Jan 1, 1934

By George B. Clark, John W. Brown, Hemendra N. Kalia, Ronald R. Rollins

A new theory for three dimensional collapse of conical liners shows why the two dimensional theory may offer a good approximation. Shaped charge design parameters and rock target properties were investigated to determine their effects on penetration and breakage. Penetration in dolomite is somewhat similar to that in steel, but copper does not have markedly better penetration capabilities than brass. Several metals, liner thicknesses, cone angles and standoff ranges for each were investigated. Effective standoff is greater for aluminum than more dense metals. Optimum geometry appears to approximate that for metal targets. Resistance to penetrations was greatest for a red granite and dense siliceous rocks, and least for dolomite and porous sandstone. Hardness and compressive strength appear to be two important conventional proper- ties. The first order law does not apply to the rocks tested. Dolomite may be drilled with shaped charges, the holes sprung and round blasted successfully.

Jan 1, 1971

Jan 1, 1951

By S. L. Crouch, C. Fairhurst

The general term "coal mine bump" refers to the sudden and violent failure of in-situ coal. Coal bumps occur in most countries where coal is worked by underground methods. They are related to geological factors and mining techniques. Coal bumps can be characterized as unstable releases of energy associated with yielding that occurs with progressive mining. Unstable releases of energy occur when the coal is able to absorb less energy than is released by the surrounding rock mass during the yielding process. At any stage of mining, the amount of excess energy so released is governed by the mining geometry, the overburden stress, the elastic properties of the rock mass, and the stress-strain characteristics of the seam material. If the coal in the vicinity of the working face is crushed, the peak abutment pressure occurs at some distance into the intact portions of the seam, and mining takes place in essentially destressed coal. With subsequent mining, additional yielding occurs, excess energy may be released, and the peak stress is again shifted into the solid. This process continues until the mining geometry is such that the zone of peak stress is effectively surrounded by yielding coal, at which point it can be anticipated that further mining will produce dramatic redistributions of stress and be accom¬panied by large releases of energy. On this basis, the differences between several alternatives for mining a given block of coal may be pronounced.

Jan 1, 1975

By R. H. Raring, F. E. Martin

A high speed gas quenching dilatometer useful in studying phase transformations in low alloy steels is described. Changes in specimen length are measured by means of an electrical micrometer tube. The maximum instantaneous cooling rate is approximately 5000°F per sec; the maximum average cooling rate from 1650' to 950°F is approximately 2900°F per sec. Data for steels of 0.11 pct and 0.67 pct C content are included. KNOWLEDGE of phase transformations as they occur in an alloy under conditions of continuous cooling affords valuable insight into its properties. The transformation characteristics during continuous cooling of steels of high hardenability, which decompose entirely to martensite at fairly slow cool-

Jan 1, 1957

By S. P. Barber, G. W. Cutting, V. Alesse, M. Ciriachi

Just what is happening in the preparation and mineral separation stages are questions frequently asked about most processing plants. It is unusual to find the answers readily available in the operating metallurgical data. Knowledge is nominally available from metallurgical balances about the head ore grade, grade and recovery of the concentrates, and the plant tailings. However, the mechanisms which control grade recovery and losses are seldom monitored in such a way as to permit specific analysis: Thus, when questions about the effectiveness of the process are asked, the answers are based frequently upon intuitive professional judgments and local expertise. Detailed investigations of process functions are extensive in terms of manpower, time, and interference with production. An investigation method in which process operating conditions could be provided in a cost effective manner would assist in local process assessment and control. Such a collection of process operating data is defined as a process audit and the development of the necessary techniques forms the subject of this paper. A typical application to a lead-zinc concentrator highlights both the manner of implementing a process and the plant data made available for local use.

Jan 1, 1980

By F. W. Gibson

A detailed description of the smelting and refining operations of the Amax-Homestake Lead Toller's smelter at Buick, Missouri. This is one of two completely new lead smelting and refining operations to go into operation in the United States in over forty years. Incorporated into the operation are the new methods and equipment which have been developed and lend themselves to the particular metallurgy of this plant. The text, as well as the statistical data presented, represent actual current practice after 22 months of operation, and although the metallurgy is considered to be relatively simple, several metallurgical problems unique to Missouri concentrates are discussed.

Jan 1, 1970

By Frederick L. Knouse

The south border of Espirito Santo begins about 400 km. north of Rio de Janeiro and extends along the Atlantic Coast northward some 325 km. and inland 100 to 150 km. The area under consideration, where quartz crystal of strategic grades has been mined, extends from 19º to 21º and 30º south latitude; and from 40º to 41º and 30º west longitude. This includes the central part of Espirito santo, chiefly south of the Rio Doce from the Atlantic ocean, and west across the border into Minas Gerais near the town of Aimores, in the municipalities of Aimores, Minas Gerais; Baixo Guandu, Santa Teresa, Santa Leopoldina, Colatina, Joao Neiva, Fundao and Domingo Mar-tines, Espirito Santo (Fig. I). During 1943 and the first half of 1944, this region accounted for approximately 3 to 5 per cent of the quartz crystal produced in Brazil. Shipments of crystal have been made chiefly by rail to Rio de Janeiro. This region is serviced by the E. F. Minas-Vitoria and E. F. Leopoldina to Rio de Janeiro through vitoria; and by the E. F. Minas-Vitoria and E. F. Centra] do Brasil through Bello Horizonte, Minas Gerais to Rio de Janeiro. The major deposits are accessible from the railheads by dirt roads, some being 5 to 30 km. off the road, reached by trail. In 1943 and the first half of 1944, the bulk of the production was from inter- mountain marshes and adjoining hillside alluvial placer deposits in the zone surrounding the town of Santa Teresa. Most of these deposits were formed from the erosion of pegmatite~, quartz veins and pockets in the gneiss, with minor quantities produced from miarolitic cavity fillings in the granitic rock. Early Operations Mining of quartz crystal in this region began in 1928 and has been stimulated by the market demand for military uses. Before 1936 little attention was given to it, either in Espirito Santo or eastern Minas Gerais. From 1936 to 1941 the Japanese sent agents to various points of production or potential production to acquire quartz through purchase. They bought crysta1 as small as 10 grams. Since '94' only the United States and Great Britain have received quartz from Brazil. The United States purchases crystals of 100 grams and larger for strategic purposes. The first known discoveries were made either in the municipalities of Aimores, Minas Gerais, or in Baixo Guandu, 01 Domingos Martines, Espirito Santo. Marketable quartz crysta1 was first found either in the massive quartz replacement veins of the Victor Hugo mine in the municipality of Domingo Martines, or in the large 'ores of quartz in the pegmatites near Baixo Guandu, extending into Minas Gerais. Production The production of quartz in Espirito Santo from 1936 through 1941 as recorded

Jan 1, 1948

By George S. Rice

The increasing use of mechanization at the face of the workings in coal mining and the consequent necessity of special supports of the roof has led, in several countries, to considerable scientific investigation, including physical tests in mines as well as on specimens of roof rocks to obtain data on the behavior of the immediate roof strata and on the effect of its pressure on supports while the coal is being mined. The investigations discussed in this paper do not include studies of the ultimate effect of subsidence and movement of the roof rock over the mine excavation, upon higher strata and the surface, but are confined to the immediate underground effects in the workings. The more recent principal investigations which have been brought to the attention of the writer are as follows: Germany.—The trial of strip packing, the usual method employed in Great Britain in longwall workings, as compared with complete packing heretofore used in Germany and in France to minimize subsidence; the behavior and strength of metal props under load; the testing of the strength of coal measure rocks, in the laboratory of the Technical High School of Breslau; and an investigation, by a special commission, concerning "bumps" as a possible cause of instantaneous outbursts of gas in coal mines of Lower Silesia. France.—The cause of instantaneous outbursts of gas in the Gard mines and tests by the official French experimental organization of the "electrical resistivity" of coal as a possible means of detecting a condition preceding an instantaneous outburst. Great Britain.—The subsidence of the roof and rise of the floor preceding and during excavation of the coal, in longwall and in room-and-pillar or bord-and-pillar workings; the compression and lateral movement of the road packs in longwall back from the face; the extent of separation of the immediate roof layers from the higher strata following mining excavation;

Jan 1, 1932

By G. H. Gilman

The campaign now being waged to improve the quality of the rock-drill bit is the natural outcome of the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc. on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack of continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination of the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and the laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved. Unfortunately, but little attention has been given to the education of the drill smith. But a few years ago, the instructions given the man

Jan 1, 1922