Search Documents

By H. C. Fiedler

THE development of the cube-on-edge secondary re-crystallization texture in Si-Fe strip depends upon the ability of inclusions to restrain normal grain growth. This ability is determined by the number and size of inclusions, which, for a given composition, is controlled by the thermal history of the material during the prior processing.' It has been shown2 that increasing the silicon content decreases the solubility of sulfur, and it is the purpose of this note to show the consequences of this decreased solubility for secondary recrystallization. Heats were made as previously described and cast into graphite molds.' The compositions are shown in Table I. Slabs 1 in. thick were cut from the ingots and either hot-rolled from 1000°C in the as-cast condition or after one of the heat treatments described later. The processing to the final gage of 12 mils followed the previous procedure.' To avoid cracking, the 5.2 pct Si alloy was cold-rolled at 150" to 200°C rather than at room temperature. The percent cube-on-edge texture developed by isothermal heat treatments was determined by dividing the maximum torque measured on disk sam-

Jan 1, 1968

By George S. Lockwood

Plans are moving ahead toward the July 1965 start-up date for Kaiser Steel Corp.’s new pelletizing plant at its Eagle Mountain, Calif., iron mine. Capacity will be 2 million long tons of pellets containing 65% Fe. A major portion of the output is scheduled for charging into Japanese blast furnaces as the result of a contract to supply Mitsubishi interests with 10.8 million tons of pellets over a six-year period. Kaiser's concentrating plant at Eagle Mountain plus sintering facilities at Fontana are adequate to meet the requirements of its blast furnaces, which, as a consequence, are not expected to take any substantial quantity of pellets during this period. However, some 200,000 tons of pellets per year is scheduled to be used for the production of special steels and in the open hearths as a substitute for the high-cost ores now being used.

Jan 8, 1964

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1985

By T. A. Rickard

The presentation to the Institute, eight years ago, of the paper of Pogepny on " The Geilesis of Ore-Deposits " has borne fruit in much fresh investigation, as is evidenced, for example, by the group of very valuable papers, by distirlguished members of the United States Geological Survey, read at the Washing-

Jan 1, 1902

By Ben L. Seegmiller

Localized open pit slope failure was avoided as an apparent result of a practical rock mechanics program conducted at the Twin Buttes copper operation. The key to the program was the application of cable bolting, a technique that artificially supports open pit slopes using properly installed post-tensioned cables. As a result of the research and testing program, extensions of the cable bolting principal became significantly apparent. • The economics of artificial stabilization appear to be overwhelmingly favorable, and • Best practical applications are "final" pit slopes, slopes beneath permanent structures and potentially slope failing areas. Success of this research is manifested by the fact that similar stabilization systems are presently under consideration for Twin Buttes as well as other open pit operations.

Jan 12, 1974

By D. A. Sangrey, D. Marcus, S. A. Miller

A methodology was developed wherein the increase in compressive strength, mineralogical changes, and pore water composition were studied simultaneously as a function of moisturized spent shale curing time. From these results the relationship between the nature of cementation process and the composition of pore water was established. Heavy metals were entrapped in the cementing constituents and the pore water became mainly a solution of alkaline sulfates. The specific data are applicable only to the material studied. But the methodology and general conclusions are useful for evaluating the environmental factors in spent shale disposal and expected leachates composition.

Jan 1, 1986

By Evangelo Agelopas

Steelmaking operators are familiar with the costs involved when ingot molds must be scrapped prematurely because of the failure of a stripping or turning lug. Some mold sizes can be expected to produce one hundred or more ingots per mold before normal wear causes the mold to become unserviceable. Therefore, the failure of lugs at less than the average life for that mold size represents a sharp increase in terms of mold cost per ingot ton produced. To combat these wasteful and costly occurrences, it was determined that an efficient method of replacing lugs should be developed to extend the life of molds which are otherwise in good condition. The purpose of this paper is to describe a lug welding method which has proved effective and economical. This method is known as the Oxygen and Mapp Process.

Jan 1, 1972

By John M. Warde, Eileen P. Burke

ORES of manganese and chrome have a high order of strategic importance, both metals are basic to the metallurgy and usefulness of steel, the fabric on which our economy rests. Looking beyond the current recession and short range picture of oversupply in these ores, this review attempts to answer the following questions regarding the longterm outlook for these key commodities: By 1970, what will be the probable demand here and abroad, what are future supply prospects, and what effect is the USSR likely to have on the world market? (See summary forecast on facing page.)

Jan 8, 1958

By H. E. T. Haultain

The study of rock crushing or grinding in tube-mills is difficult on account of the large size of the units employed in the field and the large number of variables entering into the problem. Three or four years ago, in the laboratory of the Department of Mining Engineering of the University of Toronto, a serious effort was commenced to study the matter under laboratory conditions. Experiments were carried on in a cylindrical tube-mill 18 in. long and 12 in. in diameter, inside measurements,

Jan 1, 1923

NEW MEMBERS The following list comprises the names of those persons who became members during the period of July 10, 1917, to Aug. 10, 1917. ARNOT, STANLEY L., Engr., Plymouth Cons. Gold Mines; Ltd., Plymouth, Amador Co .2 Cal. BARRETT, LESLIE PARK, Asst. Geol.... Michigan Geological Survey, Lansing, Mich. BENNIE, JOHN WILLIS Gen'l. Mgr., Shannon Copper Co., Clifton, Ariz. BRINTON, OWEN FUGATE Mgr., Admiralty Zinc Co., Quapaw, Okla. BRODERMANN, JORGE, Civil Engr., Compania Minera San Francisco, Havana,Cuba. BROWN, RICHARD HENRY JR., Sales Engr., Ingersoll Rand Co., 300 N. Broadway, St. Louis, Mo. BROWN, STANLEY Chile Exploration Co., Chuquicamata, Chile. BUDDECKE, WILLIAM A Pres., Point Milling & Mfg., Co. Mineral Point, Mo. BURGESS, GEORGE K., Physicist and Chief, Division of Metallurgy, Bureau of Standards, Washington, D. C.

Jan 9, 1917

By A. V. Henry, W. Harry Vaughan

THE kaolins of the southeastern United States were known to civilization as early as the latter part of the eighteenth century-and yet the [ ] commercial history of Georgia kaolins may be said to begin in the year 1900. The U. S. Bureau of Mines reported for that year a production of 6885 tons of "miscellaneous" clays in Georgia. A comparison of these figures with those of 1934, when the production rose to 284,556 tons (65 per cent of the domestic production), indicates the growing economic and technologic importance of this raw material. Fig. 1 clearly shows that a part of the increase is due to a normal growth in the use of kaolinitic clays and a part is due to replacement of clays formerly imported. Occurrence Georgia kaolin occurs in an irregular belt extending diagonally across the middle of the state, a distance of approximately 225 miles. This belt

Jan 1, 1937

By Edward J. Ryan, E. A. Peretti

iV preliminary X-ray and metallographic survey of the ternary system Bi-In-Te revealed that the following isopleths could form quasibinary systems: InTe-Bi, InTe-InBi, InTe-BizTe3, and InzTe3-Bi2Te3. The nature of the InTe-Bi phase diagram was established by Bologna and Peretti.' This article presents the results of an investigation of the InTe-InBi system by thermal analysis, X-ray methods, and metallographic examination. The bismuth and tellurium were bought from the American Smelting and Refining Co. The tellurium had the following spectrographic analysis: 0.0001 pct Mg, 0.0001 pct Si, 0.0001 pct Fe, 0.0002 pct Al, and 99.999+ pct Te (by difference). The bismuth assayed: 0.0001 pct Mg, 0.0001 pct Pb, 0.0001 pct Fe, 0.0001 pct Cu, and 99.999+ pct Bi (by difference). The indium was obtained from the Indium Corp. of America and contained 0.002 pct Cu, 0.006 pct Pb, 0.01 pct Sn, 0.01 pct Zn, and 99.97+pct In. The alloys were made by melting the required proPortions of InTe and in evacuated, sealed quartz

Jan 1, 1967

By C. W. Thompson

The two-way belt conveyor for coal mine service simultaneously carries coal from faces and transports men and supplies into the mine, largely eliminating the necessity for rubber-tired supply and man haulage equipment and the necessity of maintaining additional headings.

Jan 9, 1953

By Jill Dill Pasteris

Several mineralogical prospecting techniques are used in diamond exploration. Most are concerned with identifying indicator minerals such as pyrope garnet and magnesian ilmenite, which are derived from mantle xenoliths hosted by kimberlites. The first goal of such prospecting is to locate kimberlite intrusions; the second goal is to identify the diamond-bearing kimberlites. Explorationists have worked much less on the indigenous kimberlite phases. The kimberlitic opaque oxides, ilmenite and particularly spinels, promise to be useful in discriminating between intrusion episodes in identified kimberlites, and perhaps in the evaluation and prediction of diamond grades. Several petrologists have showed that spinel compositions and zoning patterns are specific to certain intrusive facies in South African and Canadian kimberlites. Careful evaluation may indicate a correlation between spinel parameters and diamond content.

Jan 1, 1984

By Allan T. Fisk, Carl R. Peterson, Richard E. Brooks, James J. Olson

Development of a continuous drill-and-blast excavation capability in mining and high-speed tunneling has been a long recognized goal. Ideally, a machine to meet the challenge should simultaneously perform drilling, explosive loading, initiation, mucking, ventilation, and other functions while remaining at the face, since the elimination or modification of the cyclic nature of the system would significantly improve the advance rate and economy of drill-and-blast tunneling. The Rapidex continuous spiral drill-and-blast concept, one of the continuous excavation schemes presently under evaluation in the US Bureau of Mines' Bedded Deposits subprogram, utilizes an unusual blasting pattern that provides effective fragmentation and involves a partially self-shielding geometry that permits a lightly shielded machine to remain at the face during blasting.

Jan 6, 1977

By C. R. Schumacher, W. H. Moyer

Cornwall, Pa. magnetite ore, containing recoverable sulfides in the form of chalcopyrite and pyrite, has been mined continuously since 1742 1 Beneficiation of the ore was begun in 1905, at the Lebanon concentrator located six miles from the mine. At first, only magnetite was recovered, using Grondal magnetic separators. In 1907, copper minerals were recovered by means of Wilfley tables. Copper flotation, attempted as early as 1912, was finally successful in 1919. In 1940, flotation of the cobalt- bearing pyrite was begun, and Cornwall ore became the major domestic source of cobait for many years. In 1916, the Bethlehem Steel Corp. began to purchase interests in the Cornwall mine and Lebanon concentrator properties, and by 1926 had acquired complete ownership. Metallurgical practice at the old Lebanon concentrator was good, but by today's standards the plant was outdated. The flowsheet was complex, due both to the mineral content of the ore and to the low capacities of much of the equipment. As the flowsheet developed, buildings were added and the plant was spread over a relatively large area, with resulting high manpower requirements. Another disadvantage was the six-mile rail haul from the mine to the Lebanon concentrator.

Jan 3, 1966

By H. E. T. Haultain

The study of rock crushing or grinding in tube-mills is difficult on account of the large size of the units employed in the field and the large number of variables entering into the problem. Three or four years ago, in the laboratory of the Department of Mining Engineering of the University of Toronto, a serious effort was commenced to study the matter under laboratory conditions. Experiments were carried on in a cylindrical tube-mill 18 in. long and 12 in. in diameter, inside measurements,

Jan 1, 1923

By Nicholas J. Grant, Gordon D. Gemmell

CREEP rupture characteristics of high purity Al-Mg solid solution alloys were studied by Mul-lendore and Grant' to investigate solid solution strengthening of pure aluminum and the accompany- ing effects on deformation and fracture characteristics. This paper presents the results of an extension of that work to A1-Cu and Al-Zn alloys to permit a comparison of the relative effects of the three solute elements on the high temperature strength and on the deformation and fracture characteristics. Experimental Procedure A total of nine alloys was studied. They were all made of ultra high purity aluminum alloyed with high purity copper, zinc and magnesium. The corn-

Jan 1, 1958

By Robert Bell

THE " Tar-Sands." is the name which has been given to the extensive horizontal deposit of fine Cretaceous sand, blackened by tarry petroleum, which forms the banks of the last or lowest 130 miles of the Athabasca river before it terminates in Athabasca lake. The Cretaceous strata, to which these sands belong, extend northwesterly from Dakota all the way to this lake and for 500 miles beyond it. The Athabasca river forms the uppermost section of the Athabasca-Mackenzie, one of the great rivers of the world. It rises on the Pacific side of the Rocky mountains, westward of Edmonton, and flows north of east to a point called Athabasca. Landing, 100 miles north of Edmonton, where it turns northward and runs about 280 miles before it falls into the west end of Athabasca lake. The section of this river-system which discharges the lake just named into Great Slave lake, is called Slave river, and below the latter lake it becomes the Mackenzie river. Along the section of 280 miles of the Athabasca river above mentioned, the Cretaceous strata consist of bluish-gray and drab-gray marls, on top, from Athabasca Landing to Drowned rapid, 110 miles down stream; then heavily bedded gray sandstones, 225 ft. in greatest thickness, underlying these, form the banks for about 40 miles further. The strata appear to be horizontal, but they really clip very slightly to the southward. At Drowned rapid, we see the first of the tar-sands resting on almost horizontal beds of bluish-gray limestone of Devonian age. In some places the limestone is associated with shaly or marly bands. Notwithstanding the great hiatus between the two series, the horizontal tar-sands lie conformably upon the almost level upper beds of the limestone wherever the two formations are seen together, all along the river, throughout a

Mar 1, 1908

By Benjamin Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of :different types of hammer drills to various mining, quarrying, and, excavating operations, that an indication of the economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not I been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the"' rock drills;" that the placing of small holes inclined upward, at angles steeper than 40° above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In' spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped, three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized.

Jan 2, 1915