Search Documents

By R. Didchenko

THERE are many methods described in the older literature which claim to produce anhydrous rare-earth chlorides in general. and cerium chloiide in

Jan 1, 1960

By Harry R. Hall

THE proposition to make pig-iron from magnetic concentrates and cobbed ore with charcoal-fuel weighing from 12 to 20 lb. per bushel is, on the face of it, not inviting; but the successful work that has been done under these adverse conditions warrants a permanent record in our Transactions, especially as it furnishes a comparison with, coke blast-furnace practice under similar conditions. The record of the furnace-practice is briefly summarized as follows:-The charcoal was made of hemlock, pine, spruce, balsam, maple, beech and birch woods. All the concentrates containing from 62 to 65 per cent. of iron would pass in. screen, of which about 34 per cent.. would pass an 80-mesh sieve. The cobbed ore, varying in composition from 32 to 47 per cent. metallic iron and from 23 to 32 per cent. of. silica, would pass through a I-in. ring, of which about 25 per cent. would pass a 1/8 in. screen. The furnace was blown in October 20,1903, with charcoal which was supposed to weigh when dry 18 lb. to the bushel. Some charcoal similar to this was stored in the stock-house for about a year and was then found to weigh 12 lb. per bushel. During the first 10 days of the blast, the furnace produced 362 tons of pig-iron, using 200 bushels of charcoal per ton of iron. From November 1st to 12th, the volume of the blast was increased gradually from 2,808 to 5,460 cu. ft. per minute, with practically no increase of output. The silicon-content of the resultant pig-iron averaged 0.75 per cent., with sulphur about 0.035 per cent. A supply of freshly-burned dry charcoal was then used which increased the silicon-content and lowered

Sep 1, 1905

By T. L. Joseph

Blast furnaces are most efficient thermally when the CO2 in the top gas is highest. Oxygen introduced in the air blast is converted to CO in the combustion zones. The extent to which CO, generated in front of the tuyeres, is converted later to CO2 depends upon the ratio of ore to coke in the charge and the degree to which CO2, formed by reduction of iron oxides with CO, reverts to CO by the secondary reaction C + CO2 = 2CO. About 300 to 400 lb. of carbon' per ton of pig iron is normally involved in the solution-loss reaction or direct reduction of FeO with carbon, which produces the same over-all results; that is, lower CO2 in the top gas. Rich2 has recently reported a reduction in fuel consumption at slower rates of blowing on two furnaces in spite of higher heat losses per ton of iron. Lower fuel consumption at slow operating rates was due to more complete reduction of the ore that resulted in higher CO2 in the top gas and consequently more efficient use of carbon. Kinney3 has reported substantial savings in fuel as a result of crushing and sizing the ore charge. Improvements in practice brought about by sintering magnetite concentrates, flue dust and fine ores have been due to the establishment of conditions favoring more complete reduction of the ore in the upper part of the furnace. The extent to which oxides and fluctuations in composition in pig iron affect the quality of steel and finished product needs further study. There is evidence that more thorough preheating and reduction of the ore in the upper part of the furnace tend to give a better quality of iron. Bogatzkii4 found from laboratory work that the amount of oxygen entering electrolytic iron, melted under various slags, was directly proportional to the concentration of free FeO in the slag and inversely proportional to the basicity of the slag. Herty and Gaines5 concluded that the silicate content of open-hearth steel before deoxidation is related to the concentration of silica in the pig-iron charge, indicating that most of the persistent inclusions are silica from the iron. They also found that

Jan 1, 1936

By W. M. Weigel

Salt production in Louisiana and Texas at the present time is entirely from salt domes of the interior and coastal groups. Before and during the Civil War salt was recovered from numerous salines and salt springs by evaporation in open kettles. The location of these in nearly every instance was near what is now known to be a salt dome, and the source of the salt in the salines and spring waters was that in the salt core. The tops of many of the shallower domes have been subjected to erosion1. The discovery that the salt occurred as large masses of rock salt in the form of domes was made in May, 1802, at Avery Island, La., by John Marsh Avery, grandson of the original owner, John C. Marsh, who built the old salt works in 18122. The first shaft for mining was sunk on the Avery dome in 1867 by Chouteau and Price. It was 90 ft. deep, about 58 ft. being in solid salt. It was abandoned in 1870. There are three general groups or fields of salt domes; interior Louisiana in northern Louisiana, interior Texas in northeastern Texas, and the coastal domes nearer the Gulf Coast and extending from the Mississippi River to the Rio Grande. This last group contains by far the greatest number of domes. As many of the coastal domes especially are prolific producers of petroleum and a few of sulfur, their geology has been intensively studied and fully covered in the literature. The depth to the top of the salt varies from near the surface, where shallow ground waters have dissolved the salt to just below recent deposits, to several thousand feet, where the depth has been cstimated only by geophysical methods. The diameter of the salt core varies from less than 1/2 mile to over 2 miles. Only domes where the salt is comparatively near the surface have been developed for commercial salt. Three deeper domes, which will be described later, have recently been developed or are in process of development, as a source of brine for chemical use. Fig. 1 shows the location of the domes so far developed for commercial salt and brine. Nos. 1, 2, 4, 7, 8, 9 and 10 are in the Gulf Coastal field,

Jan 1, 1938

By B. M. Larsen, T. E. Brower

Introduction and Summary By "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath. To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over I million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct. The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 Ib oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 Ib oxygen replacing 145 Ib ore per ton of steel) decreased the

Jan 1, 1949

By S. LeFevre

, The solution of the housing and sanitation problem in mining communities, keeping in view both economic and humanitarian aspects, demands the best thought of the management of such enterprises. Upon the solution depend the health and comfort of the employee and his family, and as a consequence his contentment and efficiency. The following description covcrs briefly the methods installed for Witherbee, Sherman & Co. The operation of the system has been for about two years under the direct supervision of T. A. Hammond, Land Agent, and I am indebted to him for a compilation of the results. Sanitation The sanitary service covers 238 tenements. The installation cost was about $22 per tenement, as follows: Privy, $15; privy box, $3; proportion of incinerator cost, $2; garbage can, $2. The operating cost is $1 per month for each tenement. In considering the installation of an ordinary village system of water supply and sewerage two difficulties were encountered: First, lack of a sufficient quantity of water; there is no stream large enough, as Mineville is situated very close to the divide between the Lake Champlain and Hudson River watersheds. A storage reservoir was tried, but the only location available, among glacial hills, would not hold water. Second, the expense of digging ditches for the distribution of water and sewer pipes is so great as to be prohibitive; Mineville is built chiefly in a valley covered in the bottom with drift, in this case a combination of boulders and hard pan. Digging in this material costs 80c. to $1 per cubic yard, and pipes must be placed 41/2 ft. down to be below frost. The houses are scattered along 4 miles of streets, the oldest having been built in the original forest 65 years ago. The newer houses have gone up a few at a time wherevcr a clear space could be found and the slopes were not too steep. This has advantages, as it separates the dwellings into

Jan 1, 1915

By T. L. Joseph

Blast furnaces are most efficient thermally when the CO2 in the top gas is highest. Oxygen introduced in the air blast is converted to CO in the combustion zones. The extent to which CO, generated in front of the tuyeres, is converted later to CO2 depends upon the ratio of ore to coke in the charge and the degree to which CO2, formed by reduction of iron oxides with CO, reverts to CO by the secondary reaction C + CO2 = 2CO. About 300 to 400 lb. of carbon' per ton of pig iron is normally involved in the solution-loss reaction or direct reduction of FeO with carbon, which produces the same over-all results; that is, lower CO2 in the top gas. Rich2 has recently reported a reduction in fuel consumption at slower rates of blowing on two furnaces in spite of higher heat losses per ton of iron. Lower fuel consumption at slow operating rates was due to more complete reduction of the ore that resulted in higher CO2 in the top gas and consequently more efficient use of carbon. Kinney3 has reported substantial savings in fuel as a result of crushing and sizing the ore charge. Improvements in practice brought about by sintering magnetite concentrates, flue dust and fine ores have been due to the establishment of conditions favoring more complete reduction of the ore in the upper part of the furnace. The extent to which oxides and fluctuations in composition in pig iron affect the quality of steel and finished product needs further study. There is evidence that more thorough preheating and reduction of the ore in the upper part of the furnace tend to give a better quality of iron. Bogatzkii4 found from laboratory work that the amount of oxygen entering electrolytic iron, melted under various slags, was directly proportional to the concentration of free FeO in the slag and inversely proportional to the basicity of the slag. Herty and Gaines5 concluded that the silicate content of open-hearth steel before deoxidation is related to the concentration of silica in the pig-iron charge, indicating that most of the persistent inclusions are silica from the iron. They also found that

Jan 1, 1936

By S. F. Emmons

IT was said by many who discussed Professor Posepny's admirable paper on the " Genesis of Ore-Deposits," read at the Chicago meeting of the Institute, in 1893, that its most valuable feature was the clear distinction which it drew between the influence upon ore-deposits of the "vadose " circulation of waters descending directly from the surface, and that of the deep underground circulation of waters generally coming from the depths, and assumed by the author to be ascending through more or less open spaces under the influence of heat. A little later the effect of the oxidizing action of the vadose circulation upon ore-deposits was ably and exhaustively treated by Prof. R. A. F. Penrose, in a paper on " The Superficial Alteration of Ore-Deposits "f-the only one, so far as I know, which has been exclusively devoted to this important subject. My own first detailed study of ore-deposits was made at Leadville, in 1880, at a time when almost the only minerals visible in those deposits were in oxidized forms. That this form was the result of the alteration of earlier sulphides by surface-waters had to be proved at the time by induction or analogy, the general correctness of which was, however, abundantly confirmed by subsequent developments. Thus I was early impressed with the importance of distinguishing, in the study of an ore-deposit, the alteration-products, resulting from the action of oxidizing waters descending from the present surface, from the earlier-formed sulphides; and, assuming that the latter were primary or original, I called the former secondary. I also went so far as to say$ with regard to oxidized ores passing into sulphides in depth "So generally is this accepted as a rule in ore-deposits that it would require special demonstration to prove beyond a doubt that the native metals or their

Jan 1, 1902

By Hjalmer Sjögren

AMONG the feldspar-rocks there are certain types which occur constantly in different areas-viz., the aruphibolitic plagioclase- rocks and the granulitic rocks Composed of quartz and alkaline feldspars. Among the latter soda: granulites as well as potash are met with; also the corresponding gneisses occur. GROUP I.-THE ORES OF THE ARCHEAN CRYSTALLINE SCHISTS. The Rocks. The ore-bearing rocks of the ore-province of central Sweden are chemically and petrographically unlike the more monotonous gneiss- and granite-areas which surround them. On the whole, they constitute a quartz-feldspar formation in which purer quartzitic rocks, limestones, " skarn " rocks, and ore-bodies are very subordinate members. (Skarn is the Swedish name for rocks of varying composition, mostly consisting of lime, magnesia, iron, and alumina, silicates of the pyroxene, amphibole, and garnet groups; as secondary minerals, epidote, chlorite, biotite, and talc occur. The skarn is scarcely an independent rock but is connected with the ore-deposits. It is formed through an interchange between the silica of the quartz-feldspar rocks and the basic constituents of the ore-formation.) [A BRIDGED SUMMARY.-The amphibolites must be considered as stretched and dynamo-metamorphosed dioritic rocks. The granulites are divided into two groups, one showing predominant plagioclase, the other equal or predominant orthoclase. Evidently, the iron-ore deposits are connected in some way with the

Jan 1, 1913

By Ralph H. Sweetser

Carbon in pig iron is not only essential but, ordinarily, it is the most abundant metalloid present; iron without carbon could not be pig iron. Carbon in pig iron has been accepted, but seldom specified. How it gets into the pig iron as it is being smelted in the blast furnace, and why just about so much of it enters into the pig iron in certain blast furnaces, and more of it,; or less of it, enters the pig iron in other blast furnaces, or in the same blast furnace under varying conditions, are problems that have not yet been satisfactorily solved. During my own practical blast-furnace experience, I collected analyses of pig iron, including the graphitic and combined carbon, and recorded them in reference to the percentage of silicon present, having in mind the generally accepted explanation that "silicon drove out the carbon." To this actual experience, I have added some analyses given to me by J. B. Rogers, who was superintendent of the blast furnaces of the Ashland Iron & Mining Co., Ashland, Ky., and was making "silvery iron" at the time. These analyses are shown in Table 1. The analyses do not tell the whole story, but they show that with Pocahontas beehive coke, the total carbon was generally high. The data relating to the composition of the slag are lacking but my own customary practice was to have a rather basic slag. During my experience in making pig iron for the Bessemer and open-hearth departments, there were times when the steel men would complain about some mysterious quality in the pig iron that caused bad steel, in spite of the fact that the percentages of silicon, sulfur, phosphorus and manganese were within the specifications. Many reasons were advanced for this undetermined "poison" in the pig iron, but the favorite one offered by the steel men was that the blast-furnace man had "oxidized" the pig iron at the tuyeres in his eagerness to get big production and low cost. To these complaints of the users of steel-making pig irons were added those of the gray iron-foundry men and the malleable iron men. These groups are unaninlous in their conclusions that the trouble lies with the blast-furnace men; but there is not yet any harmonious conclusion as to the exact cause and remedy.

Jan 1, 1927

By W. M. Weigel

Salt production in Louisiana and Texas at the present time is entirely from salt domes of the interior and coastal groups. Before and during the Civil War salt was recovered from numerous salines and salt springs by evaporation in open kettles. The location of these in nearly every instance was near what is now known to be a salt dome, and the source of the salt in the salines and spring waters was that in the salt core. The tops of many of the shallower domes have been subjected to erosion1. The discovery that the salt occurred as large masses of rock salt in the form of domes was made in May, 1802, at Avery Island, La., by John Marsh Avery, grandson of the original owner, John C. Marsh, who built the old salt works in 18122. The first shaft for mining was sunk on the Avery dome in 1867 by Chouteau and Price. It was 90 ft. deep, about 58 ft. being in solid salt. It was abandoned in 1870. There are three general groups or fields of salt domes; interior Louisiana in northern Louisiana, interior Texas in northeastern Texas, and the coastal domes nearer the Gulf Coast and extending from the Mississippi River to the Rio Grande. This last group contains by far the greatest number of domes. As many of the coastal domes especially are prolific producers of petroleum and a few of sulfur, their geology has been intensively studied and fully covered in the literature. The depth to the top of the salt varies from near the surface, where shallow ground waters have dissolved the salt to just below recent deposits, to several thousand feet, where the depth has been cstimated only by geophysical methods. The diameter of the salt core varies from less than 1/2 mile to over 2 miles. Only domes where the salt is comparatively near the surface have been developed for commercial salt. Three deeper domes, which will be described later, have recently been developed or are in process of development, as a source of brine for chemical use. Fig. 1 shows the location of the domes so far developed for commercial salt and brine. Nos. 1, 2, 4, 7, 8, 9 and 10 are in the Gulf Coastal field,

Jan 1, 1938

By B. M. Larsen, T. E. Brower

Introduction and Summary By "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath. To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over I million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct. The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 Ib oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 Ib oxygen replacing 145 Ib ore per ton of steel) decreased the

Jan 1, 1949

By M. L. Requa

This paper is abstracted from the report of the Appraisement Committee of the Independent Oil Producers' Agency, of which the writer was Chairman. The other members of the committee were M. V. McQuigg and R. S. Haseltine. To Thomas Cox, engineer in charge of the investigation, and to his efficient staff of assistants, is due the credit for the detail work necessary in carrying out the plan of the Committee. It treats only of the valuation of the lands, wells, and piping, without going into details of equipment and other features. It was recognized, early in the operation, that the value of oil lands was the value of oil ,to be extracted and marketed, less the costs attendant thereon. Referring this back to the costs in cents per barrel, it became obvious that surface improvements, absolutely necessary in the production of oil, from wells then drilled, had no separate and independent value aside from the value of the land, but that any excess equipment, not necessary for the production of oil from present wells, such as drilling tools, well casing, etc., should be given a present condition value. In valuing the properties of the Independent Oil Producers' Agency, the Committee has considered the following facts: 1. That from each property there will ultimately be produced a certain total quantity of oil. 2. That in the production of that oil a certain total quantity of money will be expended. 3. That a certain total amount of money will be received from the oil. 4. That the total net receipts will be the total gross receipts less the cost of development and production. 5. That the present value of the net receipts must be such an amount that when invested by a purchaser it will be returned with 8 per cent, interest additional during the life of the property. The initial procedure consisted in making a general reconnaissance of the entire district in which the property was located and determining the lithological and structural conditions underlying the area. The data obtained from each individual tract comprised the logs of all the wells

Jan 1, 1918

By Carl Zapffe

The manganese ore reserves of Lake Superior, because of their location and nature, have recently achieved a rnarked degree of importance as compared with the world's manganese reserves. To appreciate fully the significance and the adequacy of this reserve, one should understand how such ores are used, where obtainable, the quantity used, possible avenues for increasing use or application, and the chemical and physical characteristics of the available ores. Only with those data at hand, is it possible to arrive at a convincing answer to the question whether the reserves of manganiferous iron ores are adequate to satisfy the annual demand of the presently known iron ores for the full life of the latter. That they should last is vital; and to ascertain whether they will last was the purpose of the present investigation, which marks the first attempt to study these Lake Superior reserves. The Lake Superior region possesses and supplies the full assortment of iron ores needed for the conversion of ore into pig iron and steel ingots and castings. These ores are named bessemer, low-phosphorus and high-phosphorus non-bessemer, manganiferous and siliceous; and to include the term aluminiferous would be in keeping with the most recent nomenclature adopted by some dealers. About 35 or 40 years ago, perhaps less, most of the Lake Superior ore which is being used today was the material then considered either useless or too poor for immediate use; perhaps it was considered no more than a future reserve. An examination of the analyses of ores and the guarantees in the sales of those older times convince one that the opinions of those days must have been governed by only small differences in analyses. Some grades of ores used today in substantial amounts were used most sparingly only one or two decades ago. The relative quantities of the different ores used are ever changing; and, bit by bit, the metallurgy and the opinions are ever changing and the prejudices against certain ores and practices decrease. This is unquestionably more pronounced for the manganiferous ores than for any other kind. If, when using the present data for manganiferous ores, we will only be content to make allowances for the same experiences other kinds of ores

Jan 1, 1927

By W. A. Nordland

BISMUTH can be readily grown into single-crystal form using the so-called "quick freeze" growth method.' Some advantages of this method are that very large crystals can be grown in a relatively short time, and with comparatively simple apparatus. We have found the general quality of crystals grown by this method to be not as good as that of "pulled" crystals.' This communication describes a "quick-freeze"

Jan 1, 1968

By J. R. Thoenen

THE Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy.

Jan 1, 1947

By D. W. Peaceman

In previous papers by this author on numerical calculations of multidimensional miscible displacement, some simplifying assumptions were made in writing the dispersion term of the differential equation. It was assumed that the flow vectors were essentially parallel to the x-axis. However, in most multidimensional miscible displacements, the flow vectors are not so simply oriented with respect to the coordinate axes. This paper derives the correct dispersion term /or the more general case; gives a difference approximation /or the dispersion tern; and derives the stability criterion for the corresponding explicit difference eguation.

Jan 1, 1967

By Anwar-ul Karim

In one of our recent papers, Cheng, Karim, Langdon, and Dom1 analyzed the creep mechanisms in a Fe-4 pct Si alloy. The experimental results of apparent ac-

Jan 1, 1970

By R. A. Morse, W. W. Owens, D. R. Parrish, T. M. Geffen

Laboratory studies of several factors affecting measurements of relative permeability were made using the three-section plastic-covered core technique. Results show that the core assembly, properly constructed, will perform as a single unit, and that the testing technique will, under suitable conditions of pressure gradient, gas expansion, and migration of partial water saturation, permit measurement of flow characteristics not affected by technique. Wettability equilibrium is readily established in cores exhibiting strong wetting preference to water or oil when initially saturated with water. Laboratory tests must be conducted so that saturation changes represent those that occur in the reservoir. Immediate implications of saturation history are (1:) that the possibility exists of increasing the displacement efficiency of solution gas drive reservoirs over the natural process, and (2) residual gas saturations following water flooding in gas or gas condensate reservoirs will be 15 to 50 per cent pore space rather than 1 to 11 per cent as generally believed. INTRODUCTION Solutions of petroleum reservoir problems pertaining to production performance require the use of true relative permeability characteristics. 'This relationship of fluid conductivity and saturation has been obtained by reservoir engineers in four ways, namely: 1. From past gross reservoir performance and the extrapolation of this data based on experience,1,2 2. By using published fluid flow relationships obtained in laboratory studies on general type porous materials,3, 4, 5 3. By attempting a mathematical derivation of flow behavior," using some experimentally obtained characteristics of reservoir rocks, and 4. By laboratory flow tests using representative rock samples of a reservoir. The first three methods listed above have shortcomings which make their use limited or questionable. Production characteristics of only certain processes are obtained from field data and these are not available at the beginning of a reservoir's producing life, at which time they are desirable. It is fortuitous if general fluid flow characteristics obtained experimentally have accurate application to specific field problems. Also, it is felt that at this time there is not sufficient knowledge of the flow behavior of oil, water, and gas in porous materials to enable applicable analytical description of this to be made based on other measured rock characteristics. Measurement of relative permeability in the laboratory offers the only direct method subject to adequate checking for determination of flow characteristics applicable to field problems. Primarily, this paper deals with laboratory experiments to establish the effects of several factors on the measurement of relative permeability and the practical significance of this knowledge. Laboratory flow tests are essentially model studies; the gross reservoir being represented by a small rock sample. It is necessary to simulate in experiments all the factors of importance which influence flow in the reservoir, as well a.; to eliminate effects peculiar to the model studied to assure measurement of valid flow behavior. Factors which affect the measurement and behavior of fluid flow in porous materials have been studied by other investigators.3,7,8,9,10,11 This analysis is not intended to evaluate fully all factors involved, but to establish first the validity of measurements by the technique used and then study flow behavior under various conditions. The studies reported are as follows: 1. Effects of pressure gradient, 2. Effects of gas expansion in tests conducted at near atmospheric pressure, 3. Effects of migration of a partial water saturation in oil-gas-water systems, 4. Effects If wettability characteristics of the system. and 5. Effects of the fluid saturation history. The first three are important only in laboratory measure-

Jan 1, 1951

By J. R. Dawson, J. A. Glunt

VESTA No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin's byproduct coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War 11, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out. Mechanical loading at Vesta created new problems. It was found that selective mining, even when carefully applied, increased the refuse in the raw coal to such an extent that the washers at the mills were unable to handle it. Large tonnages of refuse were being transported, a reject disposal problem was created, and good metallurgical coal was being loaded out and lost. In addition, the selective method handicapped operation of the loading machines. Fig. 2 shows how the ash content of the raw coal increased as mechanization proceeded at No. 5 mine. New Preparation Plant: After an exhaustive study of this situation by J & L management, is was decided that a preparation plant should be constructed at the mines, capable of handling full seam mined coal and large enough to process full production of both No. 4 and No. 5 mines. It was decided that from the standpoint of inside operation and haulage the new plant should be located as near as possible to the old No. 5 tipple on the Monongahela River near Vestaburg. Full seam mining at Vesta could be expected to produce a tremendous volume of refuse along with the coal, since 14 to 16 in. of slate would be mined with an average 78 in. of coal. Disposal of this refuse required serious consideration in selecting a plant site. The only area near Vestaburg large enough for disposal of the plant refuse was across the Monongahela River at LaBelle. Ample space was available here, and construction at this location would not interfere with operation at the No. 5 tipple. It had been noted over the years that the sulfur content of the coal produced at Vesta was gradually increasing, and there was every indication that this increase could be expected to continue as the mines developed further from the river. It was decided to construct a three-part separation plant with complete blending facilities to produce both metallurgical and steam coal. In this system an attempt is made to reduce the sulfur in the metallurgical coal in a secondary cleaning process. Construction of the new preparation plant got under way early in 1947 and continued until the spring of 1950. The plant was designed to handle 2400 tph of raw coal containing 30 to 35 pct refuse. Cost of outside buildings and equipment was about $14 million. Total cost of the plant, together with improvements and changes made at this time, was approximately $21 million.

Jan 1, 1957