Search Documents

By Francisco Morganti

Weight reduction is the main target of all carmakers, which results in a continuous development of new steel grades. Latest 3rdgeneration advanced high-strength steel grades (AHSS) are complex materials with special chemical compositions and multiphase microstructures. The pickling, annealing and galvanizing processes of these grades aresomewhatdifferent due to the changed chemical compositions and microstructures. Therefore, these innovative steel grades place new demands on the plant technology of pickling, annealing and galvanizing lines. The most significant challenges for the pickling process are sludge occurrence during pickling, varying pickling times, weld ability of the materials, changed visual appearance and required high surface qualities. The most important topic concerning annealing line is a precisely controlled and very flexible heating and cooling process in the furnace.One of the new requirements in galvanizing linesis the prevention of surface faults caused by bare spots, which can occur since these materials feature a higher content of alloying elements like silicon or manganese. Prevention is possible with the special pre-oxidation technologies.Due to the higher strength of the material also the mechanical equipment has to be designed differently in these lines. This paper describes the influences of the changed chemical composition and material characteristics of modern steel grades on the pickling, annealing and galvanizing process and gives an overview about the technical solutions.

Oct 30, 2017

By Gabriel R. Royo

This paper will cover a back up roll bearing technological upgrade, being implemented at the TERNIUM SIDERAR Hot Strip Mill (HSM), in San Nicolas, Buenos Aires, Argentina. This change was motivated by increased operating loads, which caused the original bearings to be outside the designed bearing rating. The problems were first identified by bearing seizures in some stands, and later followed by cracks forming in the back up roll neck areas due to fatigue and overload. MORGOIL engineers worked together with TERNIUM SIDERAR engineers in analysing the problem and to upgrade the mill with the newest and most economical technology. The upgrade consisted of changing the bearings to the latest generation MORGOIL bearing: the KLX, which within the same space, increases bearing capacity around 25%. This was accomplished re-utilizing all chocks. The new bearing allowed for a re-design of the geometry of the back up roll neck, making it much stiffer than the original design, and eliminating fatigue failures. In addition, an upgrade to hydraulic mounting and dismounting using the MORGOIL® HB lock was also implemented, as well as changing to the newest MORGOIL® HD seals. With the MORGOIL® KLX® upgrade, TERNIUM SIDERAR HSM increased load capacity, allowing them to roll products that were not even considered decades ago. Both older oil film bearings and roller bearing mills have been successfully upgraded while reusing existing chocks and in many cases rolls. Solutions are customized to the customer’s equipment and goals.

Oct 30, 2017

By Alberto Tremea

In this period a great attention is put on roll cost and the differences in roll behavior in very few situations move the existing balances. Among many variables that are taken into account to evaluate the roll there is the consumption which is normally calculated according to the tonnage rolled. In this work there is a review of some approaches that are used to evaluate the roll efficiency together a description of a new method to make this. The main purpose of this calculation method is to help the comparison of roll results used in different mills. There is the need to have a clear and univocal reference when it’s time to think about innovative products. At now there are available roll grades with excellent technological properties but it’s necessary to have the right tools for a careful evaluation of roll behavior to take a good decision.

Jul 30, 2018

By Eric Schaub

Hot Blast Stove Systems are an important equipment of a Blast Furnace plant. During the last years, performance requirements and operation practice for the Hot Blast Systems have changed and have a big influence on the Blast Furnace operation. Therefore it is necessary to keep the Hot Blast System in proper condition in order to maintain the production capacity of the Blast Furnace. It is important for operators to know the condition and relevant constrains of a Hot Blast Stove Plant. Assessing its condition on a regular basis, especially in advance of a Blast Furnace relining is therefore advisable. Considering the individual condition of the Hot Blast Stove Plant, improvements in operation, but also specific and dedicated repairs might be implemented. Design improvements can be implemented as well during such repairs. This paper will describe some of these design improvements, will illustrate their implementation in new hot blast stoves but will also describe repair methods for existing stoves. In addition new developments became popular during the last decade, like the so called Dome Combustion Stoves, which was invented already 30 years ago in Western Europe. Paul Wurth’s development in this regard will be discussed in this paper as well.

Oct 30, 2017

By Valeria Romina Stricker

Acerbrag es una empresa Argentina siderúrgica de 50 años de trayectoria, desde el año 2007 pertenece al grupo Votorantim de origen Brasilero. Se dedica a la elaboración de aceros largos para la construcción. La planta industrial cuenta con un proceso de acería integrado, horno eléctrico, horno cuchara y máquina de colada continua. La materia prima es 100% chatarra, característica que la diferencia del resto de las acerías del país. Debido a esto el enfoque principal de este proyecto es reducir el costo de fabricación mediante un “empobrecimiento” de la carga metálica a partir de la flexibilización de los límites de especificación. Esto implica un mayor control del desempeño de los procesos a fin de detectar posibles desvíos, para ello fue necesario implementar la utilización de herramientas estadísticas y gráficas para su monitoreo. La modificación en el mix de fabricación no muestra una alteración significativa en la composición química y propiedades mecánicas de los productos terminados, situación favorable para la continuidad del proyecto. Se observa además, de la reducción de costo esperada, una ventaja en la operación del patio de chatarra y el proceso de acería y en la utilización de chatarras con altos niveles de residuales tales como Cr – Ni.

Aug 16, 2017

By Alain Denis, Marcelo Curtes Martins, Jeferson Rocio de Oliveira

In this work we present a study of optimization of a new inhibitor for turbulence pickling line. The efficiency of inhibition was measured and the weight of loss was evaluated in four different materials to optimize the dosage of the inhibitor. In seven months we had 8.7% of reduction in pickling losses.

Oct 1, 2019

By Andrea Zanon

Slitting processes have been used for many years to increase the productivity of smaller diameter deformed bars, without making major investments in the rolling mill. This technology is used mainly for the production of reinforcing bars (7-20 mm diameter), but successful applications exist also for round bar production. The multi-slitting process enables to produce up to 5 bars starting from one billet, thus increasing the productivity of the smaller products. Danieli Morgårdshammar, world leader in the supply of rolling mills for long products, has been a front-runner in slitting technology since its first applications and has recently developed, first in the world, the technology to produce 5X8mm rebar. This process has been recently applied in BRSM steel, a company based in Bangladesh which is a worldwide benchmark for slitting technology performances. This paper presents the necessary modifications which need to be considered when developing a 5-strand slitting project (and multi-strand slitting projects in general), as well as the results obtained at BSRM Steel when the process was implemented in 2016, the first rolling mill in the world rolling 5X8 mm slit rebars.

Oct 30, 2017

By Filippo Verlezza

Conventional wire rod blocks have some limitations. They can only roll with fixed reduction ratios which always require the same rolling diameters within the block. With MEERdrive® SMS, as a pioneer, has introduced an innovative drive concept for wire rod blocks that can overcome the limitations of conventional solutions. The clue: the concept is based on individual drives for each stand position. The exigent wire rod market demand and the available technology melt in a new variant of MEERdrive®, the MEERdrive®PLUS, which represents a sizing block solution for finished size rolling and allows conventional as well as thermomechanical rolling. Further “one family rolling” is also possible, since all roll / size changes will occur in this block.

Oct 30, 2017

By Rodrigo Fina Ferreira

This paper presents a mineral liberation study on two iron ore samples from the Quadrilátero Ferrífero, in Brazil: compact itabirite of low-grade metamorphism (CI) and friable itabirite of high-grade metamorphism (FI). The quartz liberation spectrum for both samples have been obtained through QEMSCAN analyses, carried out for several comminution degrees, to compare the liberation characteristics and to evaluate the evolution of the quartz’s liberation degree after fragmentation. The results have shown significant differences in liberation spectrum between the itabirite samples studied. The liberation process of FI was easier than of CI, due its high porosity and larger crystal size compared with CI, which has shown more complex mineral assemblages with low porosity and smaller crystals. The quartz liberation spectrum has shown that grinding at P95 of 0.210 mm for the FI sample, and of 0.045 mm for CI sample, should result in satisfactory liberation for subsequent concentration step.

Aug 1, 2018

By Alexandre Rizek Schultz

Silat, Siderúrgica Latino-americana, selected Russula as the main engineering contractor for their 700,000 tpy Greenfield steel plant dedicated to long and flat steel production. The project is currently under construction in the district Guararu in Caucaia in the metropolitan region of Fortaleza. The project will be developed in two phases. First phase: 600,000 tons per year rebar mill and 60,000 tpy steel mesh line; Second phase: 700,000 tpy melt shop (90 ton/hr EAF and 4 strand continuous caster for billets up to 180 mm x 180 mm).

Aug 16, 2017

By Jan Knobloch

Inter Stand Cooling (ISC) can increase productivity of a HSM and improve final mechanical properties of the strip. Constant Target Exit Temperature can be ensured for the whole strip length eliminating skid marks and other temperature oscillations of the transfer bar. The paper deals with advanced control module of ISC. Essential mathematical models of the control system is introduced and basic functionality is explained. Temperature model is based on FEM. Mechanical and thermal properties of the strip are calculated from chemical composition using neural network. Further on an experimental possibilities for investigation and design of ISC cooling headers will be shown. In conclusion practical experience with ISC on various HSM will be discussed.

Jul 30, 2018

By Ronaldo Esteves Ribeiro, Jefferson Felipe Faria Clemente, Carlos Victor Francisco dos Santos, José Herbert Dolabela da Silveira

n recent years, the market for thick plates has been highly competitive, in this scenario the plates quality is a critical success factor. In this process, the quality of the cut in thick plates is one of the important requirements for the customers, by the visual aspect as well as the technical aspect of the plate application. In the shear line, the cutting is done by shearing to trim tips, subdivide plates, trim side edges, remove samples, eliminate defects, etc. The cut is obtained by the penetration of the upper knife in the plate, causing plastic deformation in a certain region and hardening. If the clearance between the knives is adequate, the cracks will be close to the centre of the plate thickness and will result in a good cut quality. This work will present the theory of cutting of thick plates, the types of shearing, the quality of the edge in the cut, the types and the main characteristics of the knives.

Oct 1, 2019

By Gabriel Oliveira Glória

In the context of changing culture, the society is increasingly looking for environmentally friendly materials, the natural fibers appear as an option to substitute the synthetic. Among these natural fibers, the PALF fiber may be considered an option, but there is limited information about the flexural strength of epoxy composites incorporated with PALF fibers. Therefore, the objective of this work was to investigate the mechanical properties in bending tests of epoxy composites incorporated with up to 30% in volume of PALF fibers. The results showed that the PALF fiber increase the flexural strength of polymer composites.

Aug 16, 2017

By Woo, Hur, Kim, Ki Nam, Seung Min, Kyoung Sik

Tandem cold mill (TCM) is a process to obtain flatness as well as thickness desired by the customer by rolling hot-rolled coils continuously. The final stand of the TCM plays the most important role of flatness control, which usually uses the real-time measurement at the exit. However, as the material property increases, it is not easy to handle flatness with only the final stand. In order to overcome such a limitation, we propose a feedback control method to strengthen flatness control for non-final stands. The proposed method was tested in an actual production line, and the effect is proved for 45K or less steel grade.

Oct 1, 2019

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By Alberto Tremea

The eddy current system is universally recognized as a most suitable method to point out discontinuities or modifications on the roll surface. The automation of the controls through the implementation of sophisticated equipments on the grinding machine has favoured its employment in the roll shop. A big effort is still going on to clarify the best way to promptly identify situations that could be really unsafe for the roll life. The results presented in this paper have been obtained through an intensive activity conducted in field by Innse Cilindri on work rolls of finishing stands of hot strip mills. The correct interpretation of the eddy current signals and a good calibration of the automatic system have allowed, in many cases, a substantial optimisation of regrinding practices.

Aug 16, 2017

By Marcus Weldon

We are at the beginning of an era of profound transformation and human progress — a new industrial revolution. This “Automation of Everything” era will be brought about by digital interfaces, data analysis and control of the physical world through networks employing the Nokia Bell Labs Future X1 architecture — networks to support the digitization and connection of everything and everyone with the goal of automating much of life. The interconnection of robots, machines, drones, sensors, processing platforms and people through Future X networks will provide transformative tools for the automation and optimization of factories and warehouses, ports, electric grids, transportation networks, food, healthcare, construction, logistics and supply chain, emergency response, mining, and other physical industries. To date, the level of automation has been modest at best. Automating these physical industries — industries that account for 70 percent of the US Gross Domestic Product, for example — has the potential to drive significant increases in the world’s economic productivity.2 Realizing the potential of this next industrial revolution will require billions of wirelessly connected endpoints for high fidelity physical-to-digital conversion, millisecond response times to tightly control and coordinate machines and robots, and intelligent analysis to optimize real-time decisions — tasks beyond the reach of current networks. Increased levels of automation are already being achieved through the use of 4G advanced wireless access technologies. The untethering of sensors and actuators in industrial environments through the low-latency, high-bandwidth, high-reliability, and massive scale provided by 5G wireless access will complete this evolution, providing an unprecedented ability to digitize, analyze, comprehend and manipulate the physical world at a scale never previously thought possible. These new capabilities will enable us to create digital models of the physical world with ever higher levels of fidelity, further enhancing our ability to improve operational efficiencies and increase productivity and worker safety. Doing this will require a dramatic evolution in network architecture toward massively distributed cloud control and baseband capacity to achieve the required ultra-low latency and ultra-high bandwidth for industrial and infrastructure automation services — the Future X architecture. In early 2019, Nokia Bell Labs will publish a sequel to “The Future X Network: A Bell Labs Perspective”. “Future X for Industries: A Nokia Bell Labs Perspective” will explore how the Future X architecture will automate many of the world’s physical industries, including chapters devoted to electric power, cities, rail, mining, public safety, manufacturing, ports, logistics and supply chain, and an overarching chapter devoted to securing this highly automated world. To give you a small taste of the feast that’s to come, we’re sharing with you an initial installment — “Future X for Industries: Mining” — the Nokia Bell Labs view of how mining will be transformed through a Future X architecture..

Oct 1, 2019

By Edo Engel

Whereas only a handful of decades ago, typical blast furnace working volumes were below 1000 m³, such furnaces are currently designated compact or even mini blast furnaces. For certain business cases, however, small furnace sizes remain an attractive option. Decades ago, this size blast furnace would have produced a maximum of 0.3 Mtpa with its 600 m³ working volume over a campaign of up to four years. The current state of technology and operational know–how will allow a similarly sized furnace to produce over 0.7 Mtpa while achieving the multiple decade campaigns that have become familiar to steel producers in full sized operations. This level of productivity, but especially the reliability and supply security associated with mature technology, allows for integration into minimills or taking a first step towards a full scale BF–BOF integrated mill. Steel producers considering such scenarios, which are typically attractive for emerging economies, are confronted with fundamental decisions, one of which is for the technological basis for the compact or mini blast furnace to be included in the plant. This article addresses some of these decisions from an operations–based perspective. A small number of case studies is included.

Aug 16, 2017

By Christian Geerkens

Increasing requirements on slab quality initiates SMS group in developing products with a high sophisticated level regarding production and process. These characteristics are represented by SMS group’s HD family. HD stands for High Definition or the improvement of product quality via higher precision of the casting processes. A deep look inside into casting process is realized by the use of fiber optical equipped HD mold. High definition casting process control is assured using the HD spray and HD size. For objective, environmentally friendly and highly informative analyze of the inner quality of the cast products the new HD scan is present.

Aug 16, 2017

By Eduardo Vitral

The present study focuses in the simulation of pattern formation by ion beam sputtering on a material surface. This process is responsible for the appearance of unexpectedly organized patterns, such as ripples, nanodots and hexagonal arrays of nanoholes. A numerical analysis of preexisting patterns is proposed to investigate surface dynamics, based on a model derived from a Kuramoto-Sivashinsky anisotropic equation, in a two dimensional surface with periodic boundary conditions. While deterministic, its highly nonlinear character gives a rich range of results, making it possible to describe accurately different patterns. A finite-difference semi-implicit splitting scheme is employed on the discretization of the governing equation. Simulations were conducted with realistic coefficients related to physical parameters (anisotropies, beam orientation, diffusion). The study dealt with a random and a monomode 1D structure initial condition in order to understand how the shape and wavelength of the initial pattern evolve with time. Ripples and hexagonal patterns were observed in the results, being physically consistent with the phenomenon. Moreover, the Method of Manufactured Solution has been used as verification of the developed numerical scheme.

Aug 16, 2017