Search Documents

By John Hinton

Electromagnetic based (EM) sensor technology has been shown to detect changes in the magnetic permeability of steel strip travelling down the run out table after rolling. Measuring below the Curie temperature, these changes can be interpreted in terms of the phase transformation from austenite (paramagnetic) to ferrite (ferromagnetic). These real time measurements provide a detailed insight into the changes in the structure at high temperature providing the steel producer with feedback on quality control, product consistency and product development. However unlike mill microstructure models, the sensor measurement provides a point reading at a distance through the cooling course. To map the transformation in more detail, a sensor array is required along the length of the Run Out Table i.e. to measure points on the austenite to ferrite transformation curve. This paper describes the process and metallurgical factors that should be considered in the optimum design of a sensor array, i.e. the number and location of the sensor heads. Examples of cooling strategies for different steel grades e.g. low carbon, structural and dual phase steels are used to demonstrate the importance of sensor location. In addition, the effect of variability within typical industrial parameters e.g. cooling speed, on the sensitivity of sensor output and location will be considered.

Oct 1, 2019

By Ulrich Sommers

The Intelligent Furnace (I-Furnace) by SMS group is a smart furnace process and production optimization model. The combination of various tools leads to an optimized heat treatment and production process. It combines a mathematical/physical model to control the furnace with EMG’s IMPOC system for online strength measurement and a newly developed annealing microstructure model to predict material properties. This paper reports about the revamping of an existing galvanizing line, where a mathematical/physical control model has been implemented in combination with an online quality measurement system. This way, the process improvement of continuous galvanizing lines and the quality management of a range of steels including AHSS will be demonstrated. Furthermore, it gives information about the development of the annealing microstructure model to predict material characteristics. Eventually, the I-Furnace will be presented according to the current development and reference status.

Oct 30, 2017

By Yuechang Wang

A new method of manufacturing the wavy-tilt-dam(WTD) mechanical seal has been mentioned. In this method, the special equipment is designed to provide a predetermined force to external and inner circular surface of the ring. After milling the end face of the seal by grinding miller and releasing the preload, the wavy-tilt-dam can be done on the seal surface. In this paper, a prediction model is built up to investigate the relationship between the predetermined force and the deformation on the surface of the ring by using ANSYS software. A WTD ring is manufactured by this method which approves that the prediction model is in accord with the real process and this manufacturing method of the WTD mechanical seal is a proper choice.

Jul 31, 2018

By Andrelio Marcos Ribeiro, Lucio Ribeiro Camisao, Antonio Carlos Ataíde, Alan de Sousa Pereira, Renato Siqueira Campos

The annealing and pickling line n. 1, responsible for the production of stainless steel 3xx, 4xx and 430a in thicknesses from 4 to 0.4 mm, has two vertical strip accumulators. These are intended not to let the material exceed the determined time in the furnace and in the pickling, and consequently do not cause defects like burning and excessive pickling. Strip accumulator n. 1 avoids the line from stopping during welding execution of the coils in the welding machine. In sequence, the strip accumulator n. 2 avoids the line from stopping at the end cutting of the tips, and in the coils removal from the pickling. The strip accumulators have a roller table that during the strip accumulation moves vertically downwards while its counterweight moves vertically upwards, and do the inverse movement when the material is released. On December 12th 2018, the failure occurred in the strip accumulator n. 1, where it was verified that the shaft of one of the pulleys had been fractured by high-cycle mechanical fatigue, which was characterized by alternating bending. With the fracture of the shaft, occurred the unevenness of the counterweight that damaged the guides. Failure analysis of this occurrence was based on the PDCA methodology, when was verified a weld between the shaft and the pulley. The analysis of the microstructure transformation in the molten zone, in the heat affected zone and in the base metal was carried out in an optical microscope, and no abnormality was observed. It was also carried out the end test by penetrating liquid, finding an inadequate weld in its geometry, as well as longitudinal trunks along the center of the weld bead. However, after a huge investigation of the causes, it was found that the failure was triggered by an inadequate design of the pulley shaft. It was also verified that the shaft had an open measure, inadequate for the operational context. After the analysis, action plans were drawn up based on the FMEA methodology to inhibit the failure recurrence.

Oct 7, 2019

By Jörg Schwelberger

Government regulations around the world concerning environmental care are becoming more stringent, also including regulations and restrictions of depositing and use of dust, sludge and slag generated in the iron and steelmaking process. With this scenario, by-products such as iron containing dust, sludge, oxide fines, mill scales and slag, become a valuable resource and recycling may be a profitable activity within a plant. Up to ten percent in mass of the total steel output of dust, sludge and mill scale by-product materials and more than 40% of slag by product are generated within an integrated steel plant with an iron content ranging from 50% to 65% for fines and up to 25% for BOF-slag. Slags are being widely recycled and used in the cement industry, as is the case for BF slag, and in the construction industry in the case of BOF slags and EAF slags. However, value of BOF unmodified slag is typically low and environmental regulations limit the usage of the unmodified BOF slag. This paper describes innovative solutions for recycling of fines using cold briquetting technology and the modification and granulation of slag from steelmaking that increase the value of the by-product and yield a marketable product.

Aug 16, 2017

By Markus Reifferscheid

Industry 4.0, Digitalization, Internet of Things (IoT) and Cloud Computing are predominant topics in the world economy at the moment. At the ABM week 2017 Dr. Markus Reifferscheid, Head of Research & Development of SMS-group, will talk about the proceeding digitalization in the steel industry with selected examples of SMS-group. He will present advanced concepts and solutions which are currently being developed.

Oct 30, 2017

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipments in 2015. In addition to the improvement in productivity related to these new equipment, one of them the automatic surface inspection system (SIAS), work has also been developed in other equipment seeking improvement of production indicators. The present article exposes the actions and gains that were achieved with actions on two equipments in the same section as the Side Trimmer. The first one deals with the optimization of time gains with sequencing adjustments without financial contribution, using only internal labor seeking reduction of unproductive times by adjustments of the side trimmer in the cold strip mill. The second item discussed demonstrates the actions and the gains generated due to the availability of new resources (installation of SIAS equipment), the optimization of these resources seeking a focus on the reduction of ruptures in the tandem cold mill, configuring the same in the aid of the identification of critical defects and also in the automatic speed reduction action of the tandem cold mill in defects considered serious. In both cases the intention was to improve production, seeking to improve the results of the section and the line.

Oct 1, 2019

By Chad B. Donovan

There is a strong need in North America and other major steel producing markets where major capital investment in new equipment has been minimal over the past several years to make improvements to existing casting machines. In many cases, very cost effective improvements can be made to existing equipment in order to maximize the efficiency and production of an older designed continuous caster, a classic caster. SMS Group and its predecessor companies have been maintaining continuous casting molds for over forty years. This experience has allowed SMS Group to intimately understand the advantages and disadvantages of each design. The most vital component of the continuous caster is the mold copper design, as it has the most influence over the ability to cast a quality product. Updating to a modern copper design is less complicated than most steel producers think and the benefits are significant. Premium mold coatings such as UniGuard® and NanoGuard® allow casters to guard against exposed copper and wear while producing quality products for record campaign lengths.

Oct 30, 2017

By L. Martins Demuner, D. Burzic, V. Cunha Aranda, F. L. Lourenço, G. Romeu Trindade dos Santos, F. Ramstorfer

For many years, Dynamic Soft Reduction has been regarded as a proper method in improving internal quality of slabs. Even though processes models improved significantly over the past years, the efficiency of Soft Reduction was always limited by the discretization error, which inherently exists if segment rollers cannot be positioned individually. The recently developed SRD segment type allows for an individual roller positioning within the mushy zone by avoiding any discretization deviation from the optimal gap. This paper provides a detailed technological overview of the SRD segments as well as operational results at their very first implementation at Ternium Brazil.

Oct 1, 2019

By Andrea Pezza

The paper describes the recent new installation and start-up of the second RH (Recirculation Degasser) in Rio de Janeiro plant of thyssenkrupp CSA Siderúrgica do Atlântico. The new plant is installed as part of the existing RH, the twin solution increases the overall melt shop production in the area of quality plates especially for deep drawing grades. With this new equipment, CSA is able to increase degassed grades production with a state of art asset that has the ultimate technology in operation, safety and automation. The description of the main components parts and the operational concept gives an overview of the latest experience in RH plant engineering combined with best operational practice of world class steel producer.

Oct 30, 2017

By Antonio Esposito

Saving energy and reducing resource’s consumption by minimizing emissions are today great challenges in the coking industry worldwide. In order to achieve satisfying results, equipment as well as technology should be continuously improved and designed to minimize the energy requirements and to maximize the recovery of materials and energy. The sensible heat in coke pushed out of oven chamber takes up 35 ÷ 40 % of energy consumption of coke oven. Usually the coke thermal energy is lost during traditional coke wet quenching, necessary to reduce the coke temperature for the storage and the following use in steelmaking processes. BPSL CDQ project is a sample how Paul Wurth’s technology allows to reach the energy saving goal and offers an alternative to traditional quenching. With the adoption of Coke Dry Quenching process, a considerable amount of this sensible heat in the coke can be recovered by producing steam; its production depends on various parameters, some of them battery related (Volatile Matters in red hot coke) and others CDQ system related (coke burning losses, superheated steam characteristics (i.e. P,T)), greatly depending also on boiler efficiency (heat exchange efficiency, insulation of the boiler itself, air leakage, etc.). The adoption of CDQ process reduces also the water consumptions in comparison with traditional quenching.

Aug 16, 2017

By Wenting Zhu, Liqing Chen, Junjun Cui, Zhenye Chen

In this presentation, a low carbon high strength steel microalloyed with Nb and Ti was processed by thermo-mechanical controlled process (TMCP) containing two stages of controlled rolling. The austenite with various grain sizes was obtained by austenitizing this hot-rolled steel at different temperatures. And the effect of austenite grain size on bainitic transformation was investigated in a dilatometer to reveal microstructural change. The results showed that the microstructure of the hot-rolled steel was mainly composed of granular bainite, lath-like bainite, and martenite/austenite constituents (M-A constituents). With increasing the austenitizing temperature, or increasing the austenite grain size, the microstructure was changed from granular bainite to lath bainite. When the steel was reheated to a lower temperature of 860 ºC, a relatively higher start temperature (Bs) was measured for bainitic transformation. This was mainly caused by the formation of solute-depleted region in the austenite and the promotion of the granular bainitic nucleation. The highest reaction rate occurred at austenitizing temperature of 1000 ºC with fine grain size, while the coarse austenite grain can lead to a sharp increase in the amount of bainite. An analysis was made on the kinetics of bainite transformation which was controlled by the volume diffusion of C atom.

Oct 1, 2019

By Ian James McDonald

Each year, approximately 400 million tons of blast furnace slag is produced worldwide with a tapping temperature of around 1,500°C. It is normally used as a substitute for cement clinker or as an aggregate material in road construction. Currently, the slag is granulated in wet-granulation plants using large volumes of water and to date, it has not been possible to utilise the remnant heat energy of the molten slag, which amounts to approximately 1.8 GJ of energy per ton. However, in an R&D project currently underway led by Primetals Technolgies and industrial partners, a new dry atomising technology is being investigated to use air to cool molten slag and recover the lost heat energy. The resultant pelletised slag fulfils the same criteria as wet-granulated slag for use in the cement industry. Phase 1 of the project has now been completed where a technical plant was set up at the University of Leoben in 2012. A series of dry-slag granulation campaigns were carried out using remelted blast furnace slag. The elevated offgas temperatures and the quality of the slag product as verified by the FEhS Building Material Institute have shown the process suitability as an industrial application and the decision was taken to escalate the project from large laboratory scale to a full size pilot plant. The phase 2 development of this plant is now underway and is scheduled for installation at the site of an industrial partner in early 2016 where full slag flow will be fed directly to the plant from Blast Furnace ‘slag runners. This paper will show the development path taken to date and the planned route to our goal in 2016 of being the first to industrialise the ‘game changing’ process of dry Slag Granulation with Heat Recovery from the slag.

Aug 16, 2017

By Guilherme Guidugli

The hot blast stoves are a regenerative heat exchange system, accounting for 10 to 20% of the total energy requirement in an integrated steel plant, responsible for the supply of about one-third of the blast furnace heat input and responsible for a constant flow of hot air to the blast furnace, according to the required production. Because of their important role in the hot metal production, a stable operation and an appropriate combustion control is necessary. This paper aims to present the results of an investigation and modifications performed as an operating multi-furnace plant, as well as the parameters considered to ensure thermal equilibrium, improving in the stoves heating cycle.

Aug 16, 2017

By Jean-François Stumper, Mario Moser, Mark Kruessmann, Volker Langer, Daniel Bastos Martins Cruz, Claude Meisch

The latest generation of probes and casthouse machines provide a wealth of data that has not been available a few years ago. The evaluation of this data gives direct feedback to improve the blast furnace efficiency, the equipment maintenance and design and it allows the early detection of critical or deviating process situations. A stable operation with lower operation and maintenance costs are the final customer benefits.

Oct 1, 2019

By Josef Maierl

For the production of advanced high strength steel grades (AHSS) like API X80/X100, dual-phase, martensitic and complex-phase grades a number of hot strip mills need to extend their limits in terms of power and flexibility. Especially for cooling and coiling of these new materials, Primetals Technologies developed the “Power Cooling” and “Power Coiling” technologies. Power Cooling combines the advantages of conventional laminar cooling or “low pressure cooling” with the newly developed “high pressure cooling” with highest cooling rates for flexible operation. The Power Coiler which is needed to coil those high strength grades especially at thicker gauges ensures reliable strip-coiling for a most economical production. To enhance the reliable production of high-strength steel grades for a wide range of strip dimensions, the automation system with its advanced models is an integral part to the mechanical design. In this context the paper presents examples for the installation of power cooling and power coiling in new and modernized HSM.

Aug 16, 2017

By Vitor Guarnier Domiciano

The need to adjust the monolithic refractories to increasingly severe and unstable Blast Furnace casthouse operating conditions has been a major challenge for refractory suppliers in order to guarantee the runner’s safety and its availability for operation. This paper presents the properties of a new robust single line Al2O3-SiC-C refractory castable developed to endure the severe operating conditions that main runners are facing in today's Blast Furnace casthouse scenario. Practical results during almost one year of testing revealed a significant lower wear speed of the new refractory lining when compared to a standard product.

Aug 1, 2018

By Andreas Cestonaro

Roll grade evolution in plate mill applications is traditionally following the development in hot strip mills. New grades normally find their way into service only after being successfully implemented in hot strip production. The majority of the plate mills worldwide are using work roll grades that have been invented before the 1980’s. But today the demands in the mills are pushed by sophisticated product mixes and longer rolling campaigns. The result of this development is a higher wear rate on the work rolls and as a consequence roll hardness is increased and advanced roll materials are used. The backup rolls are also affected by this. The wear rate is higher and the mechanical impact in terms of contact pressure and work hardening is increasing. This paper outlines the results of the roll grade development at Gontermann-Peipers and introduces new materials for work and backup rolls for plate mills.

Jul 30, 2018

By Tiago Seixas Bittencourt

Technological developments, associated with the constant worry about the environmental impacts arising from industrial activity, it has driven the development of technologies and practices for efficient fumes and particulates capture arising from the manufacturing processes of steel in steel plants in general. Currently, the electric steelshops in operation with Electric Arc Furnaces (EAF), seek parameterize/design dedusting systems able to retain most of the particulates generated during melting and refining of steel in FEA through configurations of equipment, technologies and parameters operation in order to equalize the antagonistic relationship between effective fumes capture and energy balance of the EAF. The present work gets as a fundamental premise to evaluate critically the possible different settings of the usual dust removal systems, as well as their respective classical parameterizations. The work main purpose is to establish a general rule evaluation technique for dedusting system considering the different modes of operation of an Electric Arc Furnace.

Jul 30, 2018

By Antonio Esposito

Saving energy and reducing pollution by minimizing emissions are today great challenges in the coking industry worldwide. In order to achieve satisfying results, equipment as well as technology should be continuously improved and updated. The most modern design tools should be adopted to maximize the coke production rate also ensuring the best coke quality. In this scenario, Paul Wurth is realizing the new coke making plant of CSPecem, Ceara - Brazil. These batteries are based on Paul Wurth “jumbo oven concept”. This solution incorporates all most modern features and design upgrading, in the aim of an easy and long-lasting operation putting a particular attention to environmental performances: the reduced number of ovens and the low number of pushing per day have the main effect of reducing pollution sources. Finally the paper will highlight Paul Wurth SOPRECO® System, which is foreseen to be installed in CSPecem batteries. SOPRECO®, which is capable of controlling the pressure for each individual oven in a coke oven battery, is thus able to reduce volatile emissions through doors, roofs and stand pipes up to 90%. The coke oven gas (COG) produced during the carbonization process is cleaned in a coke oven gas treatment plant to the level stipulated by applying the Best Available Technology (BAT).

Aug 1, 2018