Search Documents

By Rameshwar Sreenivasan

This paper presents a sustainability analysis of Selective Laser Sintering (SLS) from an energy standpoint. Data of electrical power consumed by the system over an entire build were acquired using a LabVIEW 8.6 circuit. The power drawn by individual subsystems was also measured, and an energy balance was performed. These data were then used to arrive at a Total Energy Indicator of the process with the help of a specific type of Environmental and Resource Management Data (ERMD) known as Eco- Indicators, which indicates the level of sustainability of the process.

Jan 1, 2010

By E Villaescusa, A Kusui

The depth of underground mines has been increasing due to several factors, such as material demand growth and improving technology. It is a challenge to understand severe failure mechanisms such as spalling, which is caused by induced high stress. To investigate this failure mechanism under high stress conditions, intact rock blocks with small size tunnel were tested at the Western Australian School of Mines (WASM). The range of rocks, such as sandstone and granite, were drilled (200 mm hole) and tested using a servo-controlled 450 t capacity INSTRON machine. The acoustic emission sensors were attached to the block mass during the experiment to investigate the seismic response prior to spalling failure. The effect of the ground support system towards the failure was also examined by comparing the seismic response of the various ground support schemes.CITATION:Kusui, A and Villaescusa, E, 2016. Seismic response prior to spalling failure in highly stressed underground tunnels, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 689–694 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Dominic Howarth, Diana Drinkwater, Don McKee

"The pressures on mining and minerals education at the tertiary level are well known. Within Australia, for example, the number of undergraduate mining engineering courses with 30 or more students in each year has reduced to three (University of Queensland, University of New South Wales and Curtin University). Similar declines in both student numbers and participating institutions are evident in many other parts of the world, and notably in USA and most countries in Europe.An in depth study of the Australian sector was conducted in 1997/1998, resulting in the Back from the Brink report (Carter 1998). The Australian situation was summarised as follows.Australia’s minerals education system, in its current form, is fragile and is in no position to seize the opportunity (i.e. world leadership in minerals education) and is more likely to succumb to the threat.Current trends include:- an acute shortage of talented academic staff, as a result of University remuneration packages having become hopelessly uncompetitive with those in the minerals industry;- small student populations and high relative costs, making mineral specific courses vulnerable to closures, when Universities are under extreme cost pressures; this situation will be exacerbated if enrolments drop in response to, say, a cyclical down turn in the industry; and- under-resourcing of minerals departments because of their comparatively small size, making these departments incapable of delivering top class teaching in all aspects of their courses, despite being excellent in some areas.Most of the Australian issues identified above have direct parallels in other countries.The most common response of institutions to the threats is to seek strength, and in some cases survival, through various forms of linkages and networks. A number of these associations, which are frequently defensive in nature, are outlined in the paper."

Jan 1, 2003

By H Li

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The central Nanling region in South China experienced multistage granite intrusive events and corresponding metallogenic processes during the Early Yanshanian period (190–140 Ma). In this study, a wide variety of published data on age determination, petrological characteristics, major and trace elements compositions, whole rock Sr–Nd contents and zircon Hf isotopic composition of the representative granite composites were systematically collected to estimate their cooling-uplift rates, granite evolution processes and mineral deposit formation. These granites have been classified into two groups based on their age and geochemical variations: Group 1 (180–165 Ma) and Group 2 (165–150 Ma). Major and trace element geochemistry suggests that Group 2 experienced more intense magmatic evolution and differentiation than Group 1. In addition, Group 1 granitoids are classified as A1-type alkaline rocks with faster cooling and uplift rates, whereas Group 2 granites are considered as A2-type aluminous rocks with slower cooling and ascent rates. Furthermore, the Group 1 granitoids have younger Nd and Hf two-stage model ages but higher eNd(t) and eHf(t) values, indicating influence from crust–mantle interaction. In contrast, the Group 2 granites show different values, suggesting stronger upper crustal contamination or assimilation. The slowly cooled and ascended Group 2 granites experienced much heavier crustal contamination (or assimilation) and crystal fractionation, contributing to the large W–Sn mineralisation in the central Nanling region. The Early Mesoproterozoic (1.6–1.4 Ga) crustal basement of the Cathaysia Block in South China is the ore source bed for the world-famous Nanling W–Sn polymetallic mineralisation.CITATION:Li, H, 2015. Where is the source of the world-famous Nanling W–Sn polymetallic mineralisation?, in Proceedings PACRIM 2015 Congress, pp 619–622 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Libby R. Ricafort, Victorio V. Pato, R. S. Pizarro

Introduction Atlas Consolidated Mining and Development Corp. (ACMDC) started gold production at its Masbate gold mine early in 1980. This involved an open-pit mine and a 3.5-k/d (3850-stpd) carbon-in-pulp processing facility (Pizzaro and Antonio, 1981). When this operation started, the mine began stockpiling sub-grade milling material averaging 1 g/t (0.029 oz per st) gold. Furthermore, geologists estimated that there were additional low grade reserves within the ultimate pit limits. These amounted to 2.4 Mt (2.6 million st) with an average grade of 1.1 g/t (0.03 oz per st) gold. The success of low cost heap leaching prompted an investigation to determine if this tech¬nique would be applicable for the low grade Masbate ore. The findings were favorable and a series of laboratory tests were undertaken. These tests indicated the amenability of this subgrade milling ore to heap leaching. Depending on ore size, gold extractions of more than 60% were obtained. To further define operating parameters for a commercial heap leaching plant, a 400-t (440-st) batch pilot plant was built and operated. These test results were used to design the first commercial heap leaching plant in the Philippines. One design concern was the control of solutions during the rainy season. Due to the material's low grade, every effort was made to minimize capital and operating costs. To this end, surplus mining equipment from the copper operations of ACMDC and used machinery in the crushing circuit were considered. Location: The Masbate gold heap leaching operations are located on the northeastern part of Masbate Island, Philippines. This is about 480 km (300 miles) south-east of Manila. Climate: The climate is moderate with two distinct periods. The dry season runs from January through June, and the rainy season extends from July through December. During the wet season, the rainfall at the mine site averages 300 mm/m (11.8 in. per month) for a total of about 2000 mm/year (78 in. per year). However, heavy downpours in excess of 100 mm/h (4 in. per hour) can occur. Geology: Four distinct rock types have been identified in the pit area. They are tuffaceous agglomerates, andesitic agglomerates, metasedimentary rocks, and hornblende augite andesitic porphyry. The tuffaceous agglomerate occupies the northern and western flanks of the mine. Andesitic agglomerates are localized distinctly in the central portion of the volcanic plug within the mine site. The eastern boundary of the mine is occupied by metasedimentary rocks, whereas, the hornblende augite andesitic porphyry occurs as an intrusive within the andesitic agglomerate and tuffaceous agglomerate. Some areas of the pit contain high proportions of clay minerals, requiring an agglomeration step in the flowsheet. This ensures satisfactory percolation through the heaps. Ore characteristics: Gold and silver are microscopically dis-

Jan 9, 1987

By Ira Sohn

This article revisits global projections made in 1981of eight metallic and fertilizer minerals for the year 2000. The objectives here are to quantify the differences between the projected and observed levels of consumption for the year 2000 for eight of the 26 nonfuel minerals covered in the earlier study. An attempt is then made to attribute these (often) large differences to the major determinants of minerals demand — income, technological, regulatory and other policy changes, and changes in the recycling rates of the metallic minerals. The eight minerals covered are aluminum, copper, iron, mercury, nickel, phosphate rock, potash and tin. This summary article presents the actual population, gross domestic product (GDP) and per capita GDP changes from 1970 to 2000, compared with the projected rates for these important determinants of mineral use, along with the observed growth rates of minerals consumption for the eight nonfuel minerals included in this study. When the projections are compared with the observed global consumption levels for the year 2000, the differences range from +43 percent for nickel to +229 percent for potash.

Jan 1, 2005

By B. K. Shibler, W. G. Sandell, G. M. Potter, H. D. Snedden

"INTRODUCTION During the course of the investigation of the occurrence of manganese deposits in the western United States, examining 'engineers of the Bureau of Mines collected samples from seven manganese properties in Grand and beery Counties, Utah. These were supplemented by five samples submitted by property owners. Since all of the ores were too low-grade for use in producing ferromanganese for steel manufacture, some means of beneficiation was required to produce marketable concentrates, and metallurgical studies were made on each of the samples.Most of the ores Investigated are similar in one respect: At least part of the 'manganese oxide areas contains minute inclusions of gangue. This occurrence materially enhances the complexity of the ore, partly by .increasing the complexity of mineral association, but largely through making manganese-quartz liberation more difficult. In such ores, there is a marked tendency for the manganese minerals to be retained as shells or coatings on the surfaces of quartz particles when crushed. Particles of this type represent considerable loss of manganese in tailing, if gravity-concentration methods are employed, or tend to' float, thus carrying an appreciable quantity of gangue into the concentrate, if treated by flotation.Plus 48-percent manganese sinters were made from some of the ores tested, but, in general, intimate association of manganese minerals with silica limited the degree of beneficiation attainable."

Dec 1, 1947

By Jue Kou, Lei Yu, Bern Klein, Lusheng Zhou, Chunbao Sun, Genzhuang Li, Reem Roufail, Amit Kumar

Magnetic liners can improve the performance of ball mills by increasing grinding efficiency, extending service life, and reducing maintenance costs. Despite their importance, the fundamental understanding and the quantitative investigation on the effects of the magnetic liners has not been addressed in the literature. This paper addresses this gap by studying charge motion, and how the use of a magnetic liner affects the breakage mechanism of the mill, using discrete element method (DEM) modeling and the Hertz-Mindlin contact model with relative velocity dependent (RVD) rolling friction. Charge motion was modeled under different mill speeds. Compared to conventional steel and rubber liners, the charge motion in the magnetic liner mill was predominantly cascading. Quantitative analysis of the energy dissipation within the mill was conducted to investigate mill breakage. Regardless of speed, over 50% of the total energy dissipation in the magnetic liner mill was in the form of abrasion and attrition. The results highlighted the appeal of magnetic liners in secondary and regrinding application, where abrasion and attrition are considered more efficient in the fine material breakage, and where impact is ideally minimized to reduce mill wear. A number of experiments were conducted to assess the effect of different model parameters on the performance of the magnetic liner mill. The highest abrasion/attrition intensity was observed with high values of the model parameters namely the restitution coefficient, static friction coefficient, and rolling friction coefficient.

By J. E. Shigley

The gemological properties that allow natural emeralds and blue sapphires to be distinguished from other gemstones are summarized in this paper. A variety of synthetic and laboratory-treated emeralds and blue sapphires are also encountered in the jewelry industry today. Gemologists distinguish these latter materials from their natural counterparts based primarily upon features seen with magnification, such as inclusions and/or growth zoning. In some cases, however, these observations and standard gem-testing methods are insufficient, and the use of non-destructive analytical methods, such as optical spectroscopy and chemical analysis, are required for positive identification. The commercial value of synthetic and treated gems are much less, and can be insignificant in comparison to that of an important untreated natural gemstone. Identification of synthetic and treated gem material is essential to maintaining integrity in the jewelry industry. Loss of consumer confidence in the gemstones sold at the jewelry counter could have a negative impact on the exploration and mining of natural emerald and blue sapphire.

Jan 1, 1998

Confirmation that acid drainage (AD) was a significant environmental issue for the Australian minerals industry came in 1992 with the first national workshop on the topic. Subsequently the extent of AD was documented in a national survey published in 1997. The recommendations arising out of that survey served as a platform for actions by government, industry and industry-support organisations such as the Australian Centre for Mining Environmental Research (ACMER) to enable more effective prevention and management of AD. This paper briefly documents the extent of AD in the industry, the government regulations and guidelines for AD management, industry initiatives, the role of ACMER and other organisations in assisting industry through research and technology transfer, and the efforts being made to deal with AD at derelict mines. Future management of AD in the industry will be assisted by the linkage of Australia (through ACMER) into the International Network for Acid Prevention (INAP) which is facilitating the interchange of knowledge on AD as well as coordinating global research on the topic.

Jan 1, 2003

The Bureau of Mines studied available information on the nature and occurrence of potential sources of aluminum in the United States, its Pacific island possessions, and Puerto Rico to obtain data for use in evaluating the production capability and costs of extracting the aluminum from such materials. The quantity, type, and grade of the materials range from 4 billion tons of bauxite, bauxitic clay, and kaolin averaging 33 to 42 percent Al2O3 to nearly 600 billion tons of anorthosite containing only 27 percent Al2O3. Principal deposits of bauxite, bauxitic clay, and kaolin occur in Arkansas, Georgia, Hawaii, and Oregon. Major anorthosite deposits are located in New York, Wyoming, California, Idaho, and Montana. About 11 billion tons of material in deposits of various types of clay, the kyanite group of minerals, laterites, and shales averaging 27 to 30 percent Al2O3 comprise additional resource's from which aluminum some day may be extracted. Material meeting specifications of the study was found in only 22 States and the Pacific island possessions. Utilization of these large low-grade sources of aluminum awaits development of processes that are economically competitive with the Bayer process for extracting alumina from baxuite, which is at present the only commercial ore of aluminum. Changes in economic and political conditions also may play important roles in the eventual development of the potential sources of aluminum.

Jan 1, 1967

This briefing was sponsored by the Bureau of Mines to summarize ongoing and recently completed chromium-chromite research and resource assessment activities by the Bureau. Through the series of 18 presentations compiled herein, Bureau personnel covered a wide range of topics including U.S. chromite and chromium trends and usage patterns; foreign and domestic resources; and research activities on mineral characterization and beneficiation, chemical and pryometallurgical processing of chromite and chromium-bearing wastes, new low-chromium alloy and coating substitutes, corrosion- and oxidation-resistant stainless steels, and chromium-containing refractories.

Jan 1, 1986

By W. Dziurzynski

The present article sets forward the results of field tests that made it possible to validate the mathematical model used in the VENTGRAPH ventilation engineer programmes. The case considered relates to the introduction of a new heading to the ventilation network of the mine. The utilisation of computer programmes in practice is justified by the necessity of ensuring expected performance and secure conditions in the network of mine headings, where - for example - plans are being made to utilise the transport dip-heading, taking into consideration fire and methane hazards. In the article we have presented the methodology of preparation of a database for computer programmes of the VENTGRAPH system, obtained on the basis of ventilation measurements. The next step consists in the execution of a design of the modified network and prediction, this on the basis of heading geometries, of parameters characterising the flow of air for the designed headings. Due to the fact that the heading was in the final stage of driving, following its introduction to normal operation and the stabilisation of flow values it was possible to retake ventilation measurements, which validated the results obtained through computer simulations. In order to execute measurements of the volume flow in the dip-heading, we employed a new wireless multipoint measurement system to determine the velocity field of air in the mine heading; the results are characterised by a high accuracy of measurement. As a part of fire prevention and incident management planning, a series of underground fire case studies for the a validated network flow model has been made. Results of simulations show the capabilities of the FIRE module of the mentioned software, including assessment of stability of flow directions and hints on counter and preventive measures for particular locations of fire.

Jan 1, 2009

Ground falls (roof and rib) have historically been responsible for about 50% of all fatalities in bituminous underground coal mines. In some recent years, the number of ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, last year?s Crandall Canyon twin mine disasters, in which 9 miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990?s these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents in the past 5 years. Progress has also been made in pillar recovery. Safer mining technologies have reduced the number of fatal incidents, but some recent failures have underlined the need for careful management of the retreat mining process. On the other hand, more than 400 miners continue to be injured each year by rock falling from between supports, and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities. Available technologies such as roof screen, rib bolting, and inside control roof bolters could dramatically reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Andre Vervoort

Falls of ground, such as falls of roof and sidewall collapses, are a major cause of fatalities and injuries in South African collieries. Based on information obtained from the accident reports of the various Chief Inspectors of nines, a statistical analysis was conducted covering the period 1970 to 1988. This study shows that the volume of rock in a fatal fall of ground is often quite small. In intersections, fatal falls are on average larger than in roadways and at the face. It was also found that in 36 % of all fatal falls of ground no temporary or permanent support was installed at the site of the accident.

Jan 1, 1990

By J. D. Bardill

"The Stoddard mine, Cheshire County, N. H., was explored by the Bureau of Mines in 1944 as a source of the strategic fluorite. It was reported that the vein persisted in the bottom of old workings and the geology of the immediate area indicated the possibility of finding additional lenses.In its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts pre¬liminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is expressed for the cooperation and assistance given by Robert F. Sherwood of the United Feldspar & Minerals Corp.; by McHenry Mosier, chief, College Park Division, Mining Branch, who aided in re¬vising this report; and by J. B. Zadra, chief, College Park Division, Metallurgical Branch, and others of his staff, who assisted in performing the beneficiation tests and analyzing samples. The field work was under the direction of Harry P. Hermance.The property lies on the southern boundary of the town of Westmoreland, Cheshire County, N. H., at approximately 72° 39’ west longitude, 42° 27’ north latitude, in the Keene, N. H. (G.S.) quadrangle.Good gravel roads lead from paved State Highway 63 to the property. A dirt road in fair condition suitable for truck leads to the nine.Dwight H. Smith, Putney, Vt., is the owner and has leased the property to the United Feldspar & Minerals Corp., 10 East 40th Street, New York 16, N. Y.Property titles were not investigated.The fluorite deposits of Cheshire Count', H. H., have been known for many years, being reported by Jackson, (Geology and Mineralogy of New Hampshire, by Charles T, Jackson, 1844) and by Hitchcock, in1878 (Geology of Now Hampshire, vol. 3, 1878, by Charles H. Hitchcock). A large pit on the largest or east vein was mined by Lovat Frazer from about 1908 to 1917, This operation is reported to have produced approximately 3,500 tons of fluorspar. In 1917, the American Steel & Wire Co, took over the mine end is said to have produced 3,500 tons of fluorspar before relinquishing the lease in 1923.From 1935 to 1937 the New Hampshire Fluorspar Cc. operated the Stoddard mine, working chiefly on the most westerly of the three known veins on the property, as well as doing some preliminary work on the small central vein. In 1938, the United Feldspar 6 Minerals Corp. leased the mine, and less than 100 tons of fluorspar was produced from exploration and development work, No mining has been done since that time."

Sep 1, 1946

By Donald Leroux, Colin Hardie

"New or improved mathematical models of mineral processing machines are published almost on a monthly basis. Often, these models can be calibrated from bench-scale test results and programmed using spreadsheet software to simulate different designs and operating conditions in open-circuit configuration. However, since mineral processing plants frequently operate comminution, separation and/or extraction machines in closed-circuit configurations, open-circuit simulations often have limited applicability.The simulation of closed-circuit configurations necessitates the programming of an iterative loop to bring the circuit to equilibrium. This can be done by using spreadsheet software but often requires advanced programming skills. As an alternative, LIMN® software, which simplifies the programming of closed-circuit configurations within spreadsheets can be used. This software was specifically designed to turn a Microsoft EXCEL® spreadsheet into a closed-circuit modeling and simulation platform with minimal programming.During the past few years, the Mineral Processing Group at the Noranda Technology Centre, has used this software for numerous projects which include the simulation of multi-stage cyclone circuits, closed-circuit regrinding and locked-cycle flotation tests. Using these projects as examples, the flexibility and the easy to use nature of the LIMN® software is demonstrated.INTRODUCTIONMineral processing engineers routinely have to make predictions regarding comminution and separation processes. Predicting the appropriate dimensions of equipment and the process response to changes in operating mode are probably the most common situations that they face. In all cases these predictions are expected to be rapid and accurate.Predictions made by engineers are frequently based on mathematical models. Many first principles, empirical, semi-empirical, steady state and dynamic models of mineral processes can be found in the literature. In fact, new or improved mineral processing models are continuously being proposed and in spite of this variety, process engineers often have to either develop their own or tailor existing models to suit their particular needs."

Jan 1, 2003

The structure and tectonic setting has had a strong influence on gold mineralisation at the Porgera gold deposit. Here, the structural controls on the mineralisation at Porgera are discussed and placed in a regional tectonic context. The Porgera gold deposit is related to the emplacement of the Porgera Intrusive Complex. Prior to intrusive emplacement at Porgera,Papua New Guinea was affected by a major fold and thrust episode which occurred in response to arc-continent collision in the Late Miocene. After crustal shortening the region experienced a relaxation of compression which is expressed in the deformation accompanying mineralisation at Porgera. The first stage of mineralisation (stage I) is hosted by extension fractures, and is spatially associated with exposed intrusive stocks. A later episode of mineralisation (stage II) is hosted by the faults and fractures of the Roamane Fault Zone, which was active as a dip-slip normal fault during stage II mineralisation. Therefore a change in the tectonic environment from shortening to extensional tectonics can be seen at Porgera before and during mineralisation. Rapid fault-slip during stage II mineralisation may have aided high-grade gold mineralisation by subjecting hydrothermal fluids to changes in pressure, temperature, fluid-fluid and fluid-rock interaction. Uplift to form the highlands of Papua New Guinea occurred after mineralisation and was largely complete by 4.0 Ma.

Jan 1, 1995

By Ali Kahriman, Abdulkadir Karadogan, Deniz Adiquzel, Umit Ozer, Suat Bicer, Mehmet Aksoy

This paper presents the analysis and measurements of blast-induced ground vibrations during the construction of Istanbul Kagithane – Piyalepasa – Dolapdere – Dolmabahçe highway tunnels. These tunnels known as T1 and T2 are being constructed by a joint venture group. Within the scope of the study, the particle velocities and frequencies associated with 126 shots during the advancement of the tunnels were monitored and analyzed by vibration monitors at the test site. During the statistical analysis, three different predictor equations widely used in the literature were used to predict peak particle velocity (PPV) and the results and comparison of the predictor equations are presented in this paper. Finally, the particle velocities and frequency values of all blast events were evaluated according to USBM and German DIN 4150 Norms in order to determine the damage risks of the neighboring buildings and structures.

Jan 1, 2008

By Jogeshwar P. Singh, Mohamed Ashour

The Soil-Foundation-Structure-Interaction (SFSI) problem involves Kinematic Soil- Foundation Interaction occurring during large (cyclic and permanent) ground deformations as well as Inertial Foundation-Structure Interaction occurring during shaking all of which take place while the soil and possibly structural properties degrade with time. The design of the deep foundations for liquefaction induced lateral spread loads include estimation of passive pressure applied by the liquefied material as well as the amount of anticipated displacement. Coupled analyses for SFSI problems that account for liquefaction induced lateral spread and their interaction with the deep foundation system can be performed using sophisticated numerical modeling techniques based on finite element and/or finite difference methods using computer programs such as FLAC or OPENSEES. Such complete SFSI analyses are very tedious and expensive and not feasible for most projects. In 2011, California Department of Transportation (Caltrans) released guidelines for foundation loading and deformation due to liquefaction induced lateral spreading. This simpler prescriptive approach combines empirical and analytical methods through decoupled analyses using computer programs such as LPILE and SLOPE-W together with liquefaction induced lateral spread estimates based on published empirical equations. Pile group effects and pile caps are accounted for using a concept of super-pile. In this paper, we discuss the solution of the same lateral spreading related SFSI problem using computer program CGI-DFSAP (CGI-Deep Foundation System Analysis Program) based on the strain wedge theory that can account for liquefaction, lateral spreading, pile groups, pile caps and nonlinear behavior of piles in a more coupled manner to analyze the foundation system under the lateral spread loadings. CGI-DFSAP can be used to analyze piles in sloping ground conditions as well as piles beneath the abutments near a free-face slope. We have included Strain Wedge Model (SWM) solutions using CGI-DFSAP of several field and laboratory case studies of lateral spreading related to pile foundations. Finally, we have also included the SWM solution of one of the Caltrans (2011) example problems.

Jan 1, 2015