Search Documents

By R. G. B. Pickering

The hard rock gold and platinum mines in South Africa have seen little development in the technology of mining. Holes are still drilled in the rock?though the latest water hydraulic rockdrills will complete that task in two minutes compared with the eight hours for hand drilling. Charging up is with far safer explosives and with available initiation systems it is no longer necessary to run up the face lighting each fuse. Movement of rock in the stope is predominately by means of scraper buckets and scraper winches?these were first introduced in the 1920s. Support is still mainly rock, either in situ pillars or backfill, or alternatively wood. Just as the mining process has changed very little it is hardly surprising that the productivity of mining is also relatively unchanged. Major efforts have been made to mechanize the mining process. However, most of the narrow reef mines where ?trackless mechanized mining? was introduced in the early1980s have reverted to conventional mining. In the wider reefs mechanized mining is the option of choice, unfortunately most of the gold and platinum mines have very narrow reefs that are not suitable to ?off the shelf? equipment. The move to introduce room-and-pillar mining into the narrow UG2 reefs is at the expense of mining more waste with the reef, fortunately it appears that appropriate waste and reef separation processes are available. Room-and-pillar mining followed by long hole drilling and blasting of a narrow slot of reef out of the pillars currently appears to offer the best of both worlds?maximum reef recovery with minimum waste dilution.

Jan 1, 2002

By Carnevale Francesco, Bracci Laudiero Alberto, Pampanin Piero

"SummaryIn the Port of Naples a slurry wall has been realized through a sandy layer up to a deep tuff layer using the Cutting Soil Mixing technique.The executed panels have dimensions of 2.8 m x0.65 m in plan and a total length of 25 m. Primary and secondary panels have been executed using the wet to wet technique. During the panels execution the following parameters had been measured: injection pressure, injected volume, verticality. At the end of the works an exploratory campaign has been carried out through boreholes collecting samples for laboratory tests in order to verify the diaphragm thickness and its physical and mechanical properties (i.e. unit weight, unconfined compressive strength).The interpretation of the collected data allowed to verify the efficiency of the method, the volume of slurry loss due to permeation during the panels execution, the quantity of the obtained spoil compared to the volume balance equation, both for the sand and the tuff layer.Eventually, the measured physical and mechanical characteristics of the panels have been correlated to the execution method performed.IntroductionIn the Naples Port area there is a polluted site which has to be hydraulically isolated in order to prevent the pollution of the groundwater that flows from land to the sea through the Port area. A hydraulic cut-off wall has to be realized and particularly a slurry-wall realized using the CSM method had been executed.To date, two stretches have been executed, 140 an 110 m in length respectively, as shown in Figure 1 and Figure 2.After execution, the slurry-walls have been investigated with boreholes. In-situ and laboratory tests on the recovered samples of grout have been carried out; furthermore, the geotechnical parameters of the mix composing the wall have been measured."

Jan 1, 2014

By Scott Turner

GOLD AND SILVER, the monetary metals, have presented in the last year a striking contrast; gold has experienced unusual prosperity, while silver has been depressed more severely than ever before. Gold mining has been hailed as the only basic industry that is able to thrive on depression; the new gold produced is thought by many to be the most important material for the reconstruction of prosperity. Silver production, meanwhile, has been sinking to its level of 40 years ago, and its price to a level never before recorded. These factors have reduced the value of silver produced in 1932 to about the value of the average annual production more than a century ago, that of the decade 1801-1810. No other major commodity in world trade appears to have suffered a greater decline during the present depression.

Jan 1, 1933

By Greg Rasmussen

"Huckleberry Mines Ltd is an open pit porphyry copper-molybdenum mining operation located 120 km south of Houston, British Columbia with a 18,000 tpd milling facility. Huckleberry Mines is owned 60% by Princeton Mining Corporation, the operator, and 40% by Japanese partners.The Huckleberry deposit is one of several porphyry systems located in the Tahts a district of the intermontane belt of British Columbia. The principal economic minerals are chalcopyrite and molybdenite. The ore deposit is split into two ore deposits, the Main Zone, consisting of24,241,000 tonnes of mineable reserves grading 0.484 %Cu and 0.013 %Mo, and the East Zone, consisting of 66, 131,500 tonnes of mineable reserves grading 0.523 %Cu and 0.014 %Mo.The milling begins with gyratory crushing. This sizes the product down to 100% passing 6 inches. This product is discharged onto a stockpile by a stationary conveyor. The stockpile was designed for a capacity of 144,000 tonnes with a live capacity of 20,000 tonnes. Two apron feeders draw the ore from the bottom of the stockpile and discharge onto a SAG mill feed conveyor which in turn feeds a grinding circuit consisting of one 32' x 15' SAG mill and two 30' x 16.5' ball mills. The grinding cyclone overflow feeds bulk flotation at 55 -65% minus 200 mesh.The bulk flotation uses conventional rougher and column flotation methods to float a bulk concentrate recovering 92.6% copper on the East Zone and 95% copper on the Main Zone with 75% recovery molybdenum on both zones. The bulk concentrate feeds the bulk thickener which produces a density of 60 %solids. This in turn feeds the molybdenum circuit, which separates the copper and molybdenum, by depressing the copper then using conventional rougher and column flotation produces a copper concentrate of 27 %Cu and 0.02 %Mo, and a molybdenum concentrate containing 1.5 %Cu and 54 %Mo at 67% recovery. These concentrates are separately thickened, filtered, dried, and shipped to the smelter for processing."

Jan 1, 1998

By William D. Leech

Lebanon used a TBM for the firsttime to excavate a tunnel in the country. A main beam TBM, built in 1979, bored the 3.8 m (12.5-ft) diameter by 4,020 m (2.5-miles) Madiq Tunnel. The TBM bored through karstic terrain of dolomitic limestone, limestone and marly-limestone rock having near horizontal beds with more than twelve faults crossing the axis of the tunnel. The TBM also encountered more than six major karst features, filled with various combinations of boulders, clay, void space and water. The excavation through these collapsed-breccia zones drastically slowed the TBM?s progress. When complete, which the Madiq Tunnel is a part, the Kesrouane Water Project along the coast will bring fresh and irrigation waters to the parched and heavily populated region north of Beirut. The paper will describe the tunnel geologic features, karst genius, TBM upgrades and performance, and TBM/karst difficult situations

Provide an unobstructive means of measuring small changes in distance from roof to floor or from rib to rib of a mine opening and the rate of closure in order to help operators of under-ground mines detect hazardous ground conditions. Approach A small ultrasonic measurement system was developed to detect g round movement and define closure rates. How the System Works The system contains two parts: a transducer and a readout device. The small ultrasonic transducer, similar to an audio speaker diaphram, is plucked with an ultrasonic frequency every six seconds. This frequency wave is sent through the air and reflected back to the transducer off any surface at which the transducer is pointed. The amount of time needed by the ultrasonic wave to make this round trip is accurately measured using a precise oscillator / timer and is converted into a measure of distance. The accurate 6-second time interval is used to convert any subsequent changes in the reading to a rate of change in feet per minute. Two readings are then displayed alternately on the readout instrument.

Jan 1, 1984

By Russell G. Warncke

"This report is based primarily on a study of safety conditions and practices followed in the coal mines of Japan. Not all of the coal fields in Japan were studied, but typical mines in the largest producing areas and a fair cross section of coal-mine-safety conditions observed during February to April 1948 are described.Information was obtained through investigations conducted in the mines, discussions with mine-management officials and representatives of labor unions of the various mines visited, and examination of records and statistics from the various offices of the Coal Board of the Ministry of Commerce and Industry and from the Coal Association of Japan. Statistical data covering the same subject, obtained from different sources, varied in many respects and apparently were reported inaccurately, but such discrepancies can be attributed to different methods of reporting and compiling statistics.It is difficult to correlate the high fatal and nonfatal injury rates that prevail in Japanese coal mines with the conditions observed in the mines. Virtually all mines visited were attempting to prevent accidents and explosions, by apparently following known safety precautions for the prevention thereof. Some commendable safety innovations were observed at several mines; they indicated that mine officials are giving thought and consideration to hazardous conditions that affect their particular mines.Naturally, the operating officials and management were anxious to impress the writer with their interest in accident prevention and safety. Operating officials were found to be receptive to safety and wore interested in formulating definite safety programs. Some nines had well-planned and well-organized safety programs, which, if put into effect, would contribute greatly toward reduction of accidents.The approach to safety in Japan is quite different from that in the United States, especially the concept of personal responsibility for accidents and the extent to which the individual should be protected against hazards. Management is responsible for providing and maintaining safe working conditions. Collaboration between management and worker, as understood in the United States, does not exist in Japan.Increase in accidents since the cessation of hostilities is the result of unsettled economic conditions in the coal industry, influx of inexperience workers, and breakdown of discipline among the miners, who have been organized into unions. Those unions are greatly influenced by ""leftist"" tendencies.It was observed that the Japanese mine worker is fatalistic by nature and has little, if any, noticable safety consciousness. The most urgent major requirements to reduce accidents in the coal mines are to train the worker in accident prevention and instruct him regarding the inherent hazards of his occupation.Revision of the mining laws would help to reduce accidents if the companies would comply with such laws and provide safer working places and if the workers would cooperate with management and observe and comply with such laws as are enacted for their protection."

Dec 1, 1949

By T Harding, T Riggs, D Taylor

High-grade hematite ores in the Hamersley Province of Western Australia are associated with hydrothermal magnetite-apatite and magnetite-hematite-carbonate-apatite proto ores below the modern weathering surface. In addition, hydrothermal alteration of country rocks, once believed to be absent, is now recognised widely in shales and dolerites up to several hundreds of metres away from the ores. Both observations appear to exclude a simple supergene model for ugrading the host iron formations to high-grade hematite ore. Similar hydrothermal proto ores and country rock alteration are now being recognised in other high-grade hematite deposits worldwide, or have been recognised in the past.

Jan 1, 2002

Jan 1, 1963

Development of Cost-Efficient Environmentally Sound Technology for Enhanced Gold Recovery from Rebellious Gold-Containing Raw Materials Study of biochemical leaching performances in gold-bearing sulfide minerals processing enabled to develop environmentally sound technology of enhanced gold recovery from rebellious gold-containing raw materials. It was found that the ?-10 IMO bacteria activity contributes to increasing system oxygen concentrations and incrementing in rates of oxygen delivery onto surface of gold-bearing minerals. Bacteria activity products, ie, amino acids (?), support the formation of such heterocomplexes as [A-Au-CN]- , providing additional gold recovery into solutions. Technological properties of proposed bacteria solutions were studied. It was found that the proposed bacteria inoculants are capable to growing directly in process of raw materials leaching within a large pH range of media containing cyanides and thiosulfates. They oxidise the sulfur to the sulfate, as well as the antimony (III) and arsenic (III) sulfides to the pentads. For the first time, the hydrophobic cell properties, metabolites emulsifying efficiency, adsorption properties, wetting ability, surface tension and electro-kinetic potential of new bacteria strain solutions were studied as compared with chemical solutions. It was found that the proposed bacteria inoculants reduce surface tension at the solvent-mineral and solvent-concentrate phase boundaries. All aforementioned effects enhance mass transfer processes efficiency. IR-spectroscopy of new bacteria strain culture liquid allowed identifying available amino acids which substantially contribute to heterocomplex anion [A-Au-CN]- formation. Active involvement of heterotrophic bacteria in gold dissolving processes was identified. It was shown that the structure of metals complexes is substantially modified at intensive pulp agitation and during long-term storage. Fractional order reaction in biochemical and chemical gold leaching was identified. It evidences that the gold and impurity metals dissolving processes advance in synchronism. The both processes are running in diffusion zone. Biochemical leaching has advantages over chemical leaching, ie it provides enhanced rates of precious metals dissolving, improved gold recovery by 20 - 30 per cent, decreased cyanide consumption by 50 per cent. At the same time it allows to decontaminate dangerous substances contained in productive solutions produced in rebellious gold-containing raw materials processing. Basic parameters of flotation concentrates leaching by heterotrophic bacteria-assisted processing technology were tried and tested. Technology of gold sorption from leaching solutions was successfully tested.

Sep 13, 2010

By Jun Lu, Mark Van Dyke, Daniel W. H. Su, Greg Hasenfus

"This paper presents the geologic and ground control challenges that were encountered by CONSOL Energy’s mining operations in southwestern Pennsylvania. A sandstone-to-limestone geology transition was encountered by Mine A, where the primary 8-foot bolts were anchored in claystone. Upon experiencing roof sags and a roof fall in the return entry, 6-foot high-tension, fully-grouted primary bolts were employed along with 16-foot center cable bolts at every other strap to improve beam building and to ensure proper anchorage into the competent limestone. No longwall delay was reported within this geologic transition zone, although there was some difficulty in maintaining an open #2 entry airway behind the longwall face.The geologic encounter in Mine B was more complex, where fluvial deposits of massive sandstone channels, shale channels and pyritic-rich, green claystones were encountered on both sides of the mains, and which impacted both development and longwall ground control. In particular, poor transitional roof areas near the edges of the sandstone and shale channels often posed significant ground control challenges. In addition, hydraulic fracturing was sometimes utilized to enhance caving of massive sandstone behind the shields to relieve pressure at the face. Longwall face conditions and advance rates were documented to illustrate the effects of sandstone channels, shale channels, and green claystones on safety and productivity and to demonstrate the effectiveness of the hydraulic fracturing.Shale channels, slickensided zones, laminated roof zones, soft floor, and a regional syncline were encountered in Mine C, the combination of which posed unique ground control challenges during both development and longwall mining. The presence of soft floor, coupled with the presence of thick floor coal and deep cover, resulted in headgate convergence during retreat of the first right-hand longwall panel. Two-piece 8-foot bolts were sometimes observed to fail at the coupler within the laminated roof zone, and 6-foot, 1-piece, fully-grouted point-anchor bolts were employed as the primary bolts thereafter."

Jan 1, 2015

By Peter M. Watt

The objective s of this paper are: (a ) to examine and discuss the burdens we place on our extractive industry; (b) to compare the levels of taxation in Canada with those in other countries; and ( c) to suggest certain broad parameters within which our taxation policies may be made more rational and stable. Among the burdens identified are taxation, the ownership and use of our resources, environmental issues and the rather emotional issue of so-called 'super profits'. Finally, the paper will address certain broad but key areas of policy which need attention and agreement if our tax system is to be made more rational. Such areas include: whether and if so why the extractive industry should be given incentives;. what circumstances, if any, justify a 'higher' than normal' level of taxation, and, ?if the concept of economic rents is a justifiable one, how might a basis for them be established which recognizes the fluctuating value of much of the industry's output. Note: The paper was written before the 1977 Federal and Provincial budgets were presented. Consequently, the paper does not reflect any changes proposed in these budgets.

Jan 1, 1977

By J. Ronald Lawter

The purpose of the work described in this report was to measure the effects of diesel engine emissions on the air quality of work areas in a coal mine. Concentration measurements of a number of diesel related air contaminants were made at the Martin County Coal Corporation Mine in Inez, Kentucky. Compounds measured included carbon dioxide, carbon monoxide, formaldehyde, nitric oxide, and nitrogen dioxide. In addition, concentrations of the two classes of odorous compound;, aromatic hydrocarbons, and oxygenates were obtained along, with aldehyde concentrations. Surveys were made of the mine by odor analysts to determine the perceived intensity of diesel-produced odors. It was found that the concentrations of the measured species were well below their Threshold Limit Values. Odor intensity levels in the moderate to strong range were observed in the mine.

Jan 1, 1977

By D. Küster, G. Franken, P. Schütte, J. Vasters

The CTC (Certified Trading Chains) mineral certification system has been piloted in Rwanda since late 2008. CTC project implementation is jointly driven by the Federal Institute for Geosciences and Natural Resources (BGR) and the Rwanda Geology and Mines Authority (OGMR), in cooperation with other national stakeholders. Five Rwandan mineral producers participate in the CTC project with their flagship mining concessions. Based on independent third-party audits, CTC certifies supply chain due diligence measures of these companies engaged in the artisanal mining sector through on-the-ground assessments of mining conditions, transparency, as well as mineral origin and traceability. The CTC system thus allows responsible mineral producers and their clients to verifiably demonstrate supply chain due diligence and good governance in conflict-affected and high-risk areas.

Jan 1, 2011

By David Van Horsen

Operation and maintenance of California?s water tunnels is an important factor and vital link in California?s infrastructure. These tunnels are owned and operated by a variety of large and small private and public water and power utility companies, municipal agencies, and irrigation districts. Visionary pioneers such as Michael O?Shaughnessy (San Francisco Hetch Hetchy Water Supply System), William Mulholland (Los Angeles Department of Water and Power and Metropolitan Water District of Southern California?s Colorado River Aqueduct), and John Eastwood (Southern California Edison Big Creek Hydroelectric Project) built large and small water supply, irrigation and hydroelectric tunnels, which have supplied environmentally friendly-water supply, renewable electricity, and uninterrupted service to a burgeoning population and economy. This paper introduces these pioneers and describes several case histories and lessons learned during condition assessment and rehabilitation of tunnels providing enlightenment of California?s vital water projects.

Jan 1, 2008

By R. E. Hummel, J. W. Koger

IT is generally accepted that the martensitic start temperature (Ms) can be determined by resistivity measurements and is that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line.1-4 Both Titchener and ever' and pops5 have used resistivity measurements to follow the martensitic transformation in b1 Cu-Zn and ternary Cu-Zn-based b-phase alloys, respectively. Actually because of the nature of their measurements the temperature of minimum resistivity (M) was used by these authors to determine "Ms" . Also, due to experimental difficulties in detecting M, with resistivity measurements, Pops and Massalski 8 determined M, by optical microscopy. The present communication is concerned with high-precision, low-temperature resistivity measurements which reveal a definite M, temperature which differs from the temperature of minimum resistivity (M). It is also shown that M is merely the result of the geometry of the percent-transformation curve and the temperature coefficient of resistivity of the alloy. In other words, it will be demonstrated that M has no apparent significance (except that it denotes a temperature at which some percent of martensite can be detected in a given alloy). Alloy specimens were made by melting 99.999 pct Cu and 99.9999 pct Zn in sealed and evacuated quartz tubes and homogenizing them at 601PC for 300 hr. After the alloy was cold-rolled into foils suitable for resistivity measurements, it was quenched in ice water from 871PC. The chemical analysis showed a zinc content of 38.8 wt pct. The cooling rate during the martensite transformation was 1°C per min and was controlled with a thermistor. Electrical resistivity measurements were made using a K-3 type potentiometer; the reproducibility of the resistivity values was better than 0.03 pct. Temperatures were measured with a thermocouple to an accuracy of better than 0.2° C. Fig. 1 shows the resistivity vs temperature curves of the martensitic transformation in B1 Cu-Zn for both cooling and heating. The starting point of the martensitic transformation (M,) was taken as that

Jan 1, 1968

By J. A. Finch

"A method of sampling and presenting bubbles for imaging for use in full-size flotation cells is described. The device (bubble viewer) comprises a tube attached to a sealed glass viewing chamber. The assembly is first filled with frother-containing water (to prevent coalescence) and the tube immersed at the desired location below the froth. For a few minutes bubbles are collected in the viewer free from slurry and are readily imaged. To reduce bubble overlap and the problem of defining the plane of view, the viewing chamber has a sloped side. Bubbles rise, encounter this slope, spread into a single plane and slide up. This simple expedient virtually eliminates overlap and provides an unambiguous focus plane - the underside of the sloped glass. The bubble image is captured and processed to give size data. The bubble viewer has been employed at several concentrators on different types of flotation cells. Examples of the images are given. The impact of position in the cell and the effect of changing gas rate on bubble size are illustrated. This technique provides a sensitive measure of the effects of process variables on bubble size.INTRODUCTIONDespite the extensive use of flotation in the mineral processing industry, the methodology employed for cell design is largely based on empirical rules rather than on first principles. One of the main reasons for this state of affairs is that the local flow structures encountered in industrial-scale machines are very complex. These flow structures are difficult to simulate under the controlled conditions of the laboratory and the difficulty to solve the mathematical models that treat the randomness of such flows also mean theoretical treatment is limited. Understanding flotation cell hydrodynamics requires reliable data, which involves the implementation of measurement techniques capable of performing both at the laboratory- and the industrial-scale, In addition, it is desirable that such techniques are amenable to automation to reduce extensive manual intervention in the data collection process."

Jan 1, 2002

By R. Flatabø, K-E. Johansen, L. Hunsbedt, P. M. Cowx, J. A. Bustnes

Eramet and Tinfos are two producers of manganese alloys in Norway, which have worked hard for several decades to improve both the internal and external environment. Furnaces producing ferro- and silico- manganese alloys generate large amounts of off-gas that contains substantial amounts of dust, heavy metals and organic by-products. The dust is separated from the gas in venturi scrubbers by washing with water. The water is cleaned and recirculated, and the surplus water coming from moisture in the raw materials, is discharged to the adjacent fjords after further treatment. Emission figures show that the discharge of suspended solids, manganese, zinc and PAH (polycyclic aromatic hydrocarbons) have been reduced substantially over the last three decades as a result of process improvements and installation of state of the art environmental control measures. The two plants were the first world wide to install mercury cleaning of the off-gases from the furnaces. Mercury emission reduction has exceeded 90%. Concerning other environmental issues, such as utilisation of off-gases for energy recovery and chemical purposes, both plants have achieved good results. Major effort in the environmental work has come from the plants themselves, but other players like FFF, The Norwegian Ferroalloy Producers Research Association, and SFT, The Norwegian Pollution Control Authority, have contributed to the achieved results.

Jan 1, 2007

By L. M. Gould

"Syncrude Canada operates the largest oil sands crude oil production facility in the world and produces over 13% of Canada’s total oil requirements. To achieve this, Syncrude mines the oil sands in open pits, extracts the raw oil known as bitumen from the sand using water-based processes and upgrades it into sweet light crude oil by fluid coking, hydroprocessing, hydrotreating and reblending. The final product, Syncrude Sweet Blend (SSB), is sent by pipeline to three Edmonton area refineries and then to pipeline terminals which ship the SSB to refineries in Canada and the United States.As parts of the Mildred Lake base mine reached their economic life, they were replaced with new facilities at the Aurora Satellite mine. Aurora is situated on Oilsand Leases 10, 12 and 34, 35 km northeast of the Mildred Lake facility (Fig. 1).In 2000, the first hydrotransport low-energy extraction production train started up at Aurora. A second production train is scheduled for start-up in 2003. Open pit mining at Aurora occurs using two hydraulic shovels, two cable shovels, and trucks ranging from 320-ton to 380-ton payload capacities (Fig. 2).Once the oil sands is excavated, the trucks dump the ore into a crusher designed to break up the big lumps of oil sands and rock at peak rates of 11 000 t/hr. The ore is then transferred by conveyor to a surge pile and then to a mixing box which combines the oil sands with hot water. Following bitumen separation in the primary separation vessel, froth is delivered to Mildred Lake for processing via the intersite pipeline (Fig. 3).The goal of this paper is to illustrate how high precision shovel GPS (HPGPS) is being used at the Aurora mine to aid in mine planning. This can be accomplished by first describing the function of the mine planning department, describing the Aurora orebody, and finally explaining how the HPGPS system functions and how it is employed at Aurora.The short range mine planning department ensures a steady supply of ore is delivered to the plant at the desired grade in a sequenced and economical manner. This is done by creating a mine plan that consists of shovel dig locations that require the shovels to mine in a specified area at a specified elevation."

Jan 1, 2002

New Zealand depends on foreign investment for economic development. This also applies to the development of New Zealand's mineral resources. For this foreign investment to happen there must be some incentives to attract the investment. While prospectivity is the dominant parameter considered by investors it is not a variable that can be changed, only the perception of New Zealand's prospectivity. Other parameters likely to be considered are sovereign risk, red tape, green tape, land access, civil unrest, land claims, social risk, labour relations, infrastructure and natural disasters. Regulators and political will can vary some of these parameters. Where New Zealand fits internationally can be measured by investors' perceptions of these parameters. Following on from these perceptions New Zealand can be seen to have advantages in some areas and be disadvantaged in others. How to deal with the disadvantages to give investors confidence is not easy in the New Zealand environment where the development of mineral resources plays a small part in an economy dominated by agriculture. Added to this is the current global state of the minerals industry which offers even more of a challenge to attract foreign investment to develop New Zealand's mineral resources.

Jan 1, 2000