Search Documents

By Gregory T. Ziegler

A complex soil profile and high water table, together with a below-grade active subway tunnel, an above-ground elevated railway line, and the heavily travelled Northern Boulevard all passing above the tunnel alignment, combined to make mining of New York?s Northern Boulevard Crossing what is widely considered to be the most challenging portion of the multi-billion-dollar East Side Access project. The Northern Boulevard Crossing is a vital link in this project which, when completed, will connect the Long Island Railroad to Grand Central Terminal in Manhattan. How the sequential excavation method (SEM) tunneling was successfully accomplished, despite the obstacles, was a textbook exercise in practical innovation coupled with close cooperation between the owner, the construction manager, Hatch Mott MacDonald, the designer, Parsons Brinckerhoff, the contractor, Schiavone-Kiewit, and spe-cialty geotechnical contractor, Moretrench.

Sep 1, 2013

By Verne E. Hooker

Stress-relief techniques and instrumentation have been developed through many years of research in the Federal Bureau of Mines and successfully used to determine the in situ state of stress in rock. This paper describes the drilling equipment and accessories for use with the Federal Bureau of Mines three-component deformation borehole gage. Operation and calibration procedures for the deformation gage are discussed in detail. Site selection and overcoring procedures are included to provide a complete working knowledge for surface or underground applications.

Jan 1, 1974

By David Belknap, Clay Haynes, David Egger

Rehabilitation challenges were met nearly two months ahead of contract schedule for the Design-Build, Fast Track Scituate Aqueduct & Tunnel project in Cranston, Rhode Island. The aqueduct and tunnel were built in the 1920s and consisted of three sections—a 2.3 m diameter reinforced concrete section that extends approximately305 m before it transitions to a horseshoe-shaped 2.3 m wide by 2.1 m high cast-in-place concrete tunnel that continues for approximately 5.3 km until it transitions back to a 2.3 m circular section that extends approximately 1.9 km to the end of this project. Major repairs were required to assure sustained operation of this water supply tunnel.

Jan 1, 2005

By David L. Veith

This Bureau of Mines bibliography of U.S. and Canadian literature pertaining to revegetating coal-mined lands contains 805 references published from 1977 to 1984. Each reference is evaluated by keywords, providing the reader with a means of rapidly sorting through the references to locate only those dealing with the coal mining region and subject of interest. All references are annotated. Other sources of information are given, including Office of Surface Mining (OSM) and State reclamation agencies and other published bibliographies.

Jan 1, 1985

The following paper describes the refining practice for the production of lead, silver and gold at the works of The Broken Hill Associated Smelters Pty. Ltd., Port Pirie, South Australia.The refinery is situated on the wharf frontage and is built parallel with it. The refinery occupies an area of approximately 3380 square yards. (Fig. 8)There are two buildings, one containing the softening and de-silverising sections, measuring 225 ft. x 57t ft., while the other building, which measures 225 ft. x 90 ft. covers the de-zincing, lead moulding, retorting, cupellation, and dore parting sections. (Fig. 1)The retorting, cupellation, and dore parting sections are completely isolated from the rest of the plant by strong small-mesh wire gratings welded to steel uprights. The dore parting plant and generator room are further isolated by a brick wall, built up to the roof. The two main buildings are steel structures, with outer walls and roof of "Robertson" corrugated sheeting; the side and end walls are open for some distance above the ground, and this, coupled with the high roof which is 50 ft. from ground level, ensures the free access of air and light. Conditions are such that operators work in a clear atmosphere.

Jan 1, 1937

These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar in September 1981 for the purpose of disseminating recent advances in mining technology in the area of premining research. The introduction and descriptive papers discuss techniques and instrumentation used in premining research for metal and nonmetal mining and shaft design and borehole control for premine planning.

Jan 1, 1982

By A. C. Neiva

An energy-dispersive x-ray fluorescence spectrometer was assembled with the aim of analysing alloys and corrosion products of artistic, ethnological and archaeological pieces. The spectrometer is semiportable and consists basically of an 60kV/1.5mA X-ray tube with W anode and a Si-drift X-ray detector with Peltier cooling, with no need of liquid nitrogen. It was used for the analysis of the alloys and occasional corrosion products of several metallic pre-Hispanic pieces of the Museum of Ethnology and Archaeology of the University of São Paulo. Special care was taken to account for the contribution of spurious radiation from both the Pb primary collimator and the Zr detector collimator. The main components of most alloys were Au, Ag and Cu, but Pb, Ca, Fe and other elements were also identified. The characterization of the alloys and corrosion products is important for the subsequent conservation of the collection.

Jan 1, 2006

The past decade has seen revolutionary advances in communications and information-handling techniques which have been stimulated by "cold war" military requirements and by current programmes for probing into outer space. The tools used in exploration for petroleum and minerals have been improved significantly as a result of this new space age technology and even greater improvements are on the way.Two areas of technical activity have been particularly fruitful in enhancing the effectiveness of exploration methods. These are1. the development of new approaches, based on information theory,for extracting signal from noise more efficiently than before, and2. the use of high-speed digital computers for storing and processing all kinds of exploration information, not only geophysical but geological as well.In seismic prospecting, use of information theory has led to new techniques such as time-domain filtering, wave-number filtering and correlation methods which have made it possible to obtain usable reflection data from areas which were previously considered non reflective. Complex playback and other data processing facilities have been developed to apply these approaches.Digitization of geophysical data for handling by high-speed electronic computers facilitates many of these techniques for signal-to-noise improvement. Direct digital recording of seismic data in the field is now being d'one on an experimental basis in the United States, and this should become a standard procedure, at least for problem areas.The increased dynamic range, flexibility of filtering and other data processing, and convenience of information storage and retrieval make digital recording attractive in spite of its high cost compared to conventional analogue methods. Digital computers are being programmed to carry out many operations in data reduction and interpretation with substantial savings in time and cost over conventional procedures.INTROPUCTIONIn the years that have passed since the end of the Second World War, the western world has witnessed a technological revolution which may be as far reaching in its ultimate impqct as the Industrial Revolution of the last century.

Jan 1, 1963

Even though the economy of the United States remains in recession ? or not, depending on which economist you listen to ? muicipalities still need improved transportation, water and wastewater transit systems. And they are willing to spend the necessary funds on those systems, provided they are affordable, environ-mentally friendly and sustainable. From June 20-23, professionals in the tunneling and underground construction industry from around the world gathered in Portland, OR to learn new ways of providing those systems using the latest technology available. The North American Tunneling (NAT) conference attracted 803 attendees and 108 exhibiting suppliers of equipment and services.

Jan 1, 2010

By Jerry C. Tien

Changes and the pace of change in China’s coal industry have been extraordinary during the past several years. At least 35 of the 94 former coal bureaus have been restructured into different mining companies and groups. Some of the more productive and efficient ones were further strengthened through consolidation and expansions. And several have even formed, or are in the process of forming, strategic alliances with utility companies, railroads, ports and chemical companies to secure additional reserves and coal sales. In addition, the improvement in coal pricing during the past two years has enabled China’s coal industry to move ahead with some needed changes. Coal mining accidents, though, remain a major concern for the Chinese government. Accidents remain high even though the government has made efforts to shutdown more than 55,000 unlicensed, unsafe small coal operations throughout the country.

Jan 1, 2003

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or non- volatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this report. Data mere obtained, on application of such locomotives to cod mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By R. Chen

Most tunnels built in Sydney encounter similar ground situations; they penetrate either the Hawkesbury Sandstone or the shales that lie beneath the city. Tunnels in these materials are generally sup-ported by rock bolts in combination with a shotcrete lining. A method of analysis is presented to improve our understanding of the long term behaviour of fiber reinforced shotcrete (FRS) materials and the tunnel support systems. A finite element method SAFEA (Semi-analytical FE Analysis) is developed to model the combined creep behaviour of a shotcrete lining and the Hawkesbury Sandstone. To model the time-dependent creep behaviour, the bulk modulus and shear modulus of the materials are represented by logarithmic functions in time. A Laplace transform is then applied to these functions of time and the solution of the problem found from a finite element analysis. Tablot?s method is then used to invert the transformed values and find the solution in real time. The time dependent creep deflection of the numerical tunnel models reflects the interaction of the shotcrete lining and rock which have different creep parameters.

Jan 1, 2008

By Sikko Doornbos

For the extension of the Paper Mill of Parenco in Renkum, the Netherlands, the application of a pile foundation was required. The demands for this pile foundation were very explicit a vibration free and soil displacing pile systems with low allowable settlement. Another important aspect was the total amount of piles (originally over 1600 auger piles) which had to be executed within 3 months, in very difficult and unhomogeneous soil. Based upon these conditions the Tubex Grout Injection Pile was chosen to be used for this project. This system involves the drilling of a steel tube with a conical pile shoe while grout is injected at the point simultaneously, creating a mixed-in-place layer around the tube. INTRODUCTION After extensive marketing, the board of directors of Parenco, decided to a large extension of the production capacity of its paper mill by building a new production building called Paper Mill 1 or PM-1. The new PM-1 extension had to be constructed beside the existing PM-2 because of limited terrain. The site is located right between the Rhine river and Renkum, approximately 15 kilometers (10 miles) west from Arnhem (see figure 1). The construction involved the building of the PM-1 extension of approximately 250 meters (820 ft.) long by 40-60 metres wide (130-200 ft.). The main structure was to be constructed of precast concrete beams and columns.

Jan 1, 1987

VOLUME II Volume II, in conjunction with Volume I, is a general guide to the selection of cost-effective methods of site data acquisition in all geologic environmental, and socio-political circumstances. The judgement of a generalist or trained specialist must be relied upon in the final analysis to design the optimum program for a specific site.

Jan 1, 1976

By P M. Hancock, Associates

Lacustrine sediments, hydrothermal explosion breccias and spring precipitates deposited 5200 - 1800 years BP as a result of geothermal activity at Lake Rotokaua, contain New Zealand's largest known sulphur reserves. Current drill indicated reserves are 2 600 000 tonnes of elemental sulphur, assuming a ten per cent (dry basis) cut-off, contained in some 17 000 000 tonnes of ore with an average grade of 214.0 per cent (dry basis) sulphur. Additional inferred ore containing 500 000 - 900 000 tonnes of sulphur has yet to be prospected by drilling. Geological factors will be important in exploitation of the deposit, particularly the extent and disposition of the orebody, sulphur grades and distribution, physical characteristics of the ore, permeability and stability of the overburden and the nature and extent of geothermal activity in the area. Trials to date indicate that Frasch mining and possibly opencutting are unlikely to be successful mining methods. Further mining feasibility studies will be required to ascertain the most likely mining system for the deposit.

Jan 1, 1984

Possibilities and Working of the Specific Agglomeration of Fibrous Materials and Residues Plant based fibrous materials are becoming of increasing interest in a multitude of industrial applications. Main advantages are the specific lower energy demand and virtually closed CO2 cycle, excellent mechanical properties based on low density as well as a high level of recyclables. In contrast, processing and handling of such materials is associated with a number of challenges. These challenges are mainly related to specific morphological characteristics in correlation to fibre length and structure (branching and splices). Specific problems in further processing steps including transport, dosage or storage for natural fibre compounding, result from form-locking bonds leading to burling, clusters or plaits. Technologies of fibre processing are well known, but other than textile based technologies they generally result in intermediate goods which do not allow direct industrial application. The investigation to be presented is based on results of recent research activities and shows two possible technical solutions of innovative fibre agglomeration procedures. These methods allow the conversion of middle to long fibres into a form, which eases further processing and dosage significantly and therefore allows free flowing too. The procedures are based on the working principles of rolling and winding technology. Within the work, both of the patented methods and their respected lab-scaled devices will be described. Further, results will be shown for an up-scaled rolling agglomeration unit applying the developed principle and consisting of multiple process zones. Possible variations of the resulting product characteristics and the impact of different process parameters will be discussed based on the trials with natural fibre (hemp and flax) agglomeration. As a main outcome of the research, product qualities can be supplied according to the requirements of the specific application in correlation to agglomerate strength, porosity or form. In conclusion, recent developments for specific methods of characterization will be depicted.

Sep 13, 2010

By Koehler Stout

Many hydraulic backfills are deposited at low density and provide less than optimum support strength to stope walls. This laboratory study shove that fill strength can be considerably increased. Placement methods used to increase the fill strength were the head, vibratory, cementation, double-planed (dblplod), and combinations of these methods. An experimental facility van designed to study the placement cathode and resultant strengths of the fills. Physical property tests made on the fills included laboratory penetration and vane shear plus several supplementary tests, such as grain size distribution and relative density. Test results were compared to fills planed by conventional methods and to those results reported by other investigators. When compared to fills placed by conventional methods, the penetration modulus was increased by 4.3 tines when the uncemented-vibrated-head concept was used and 71 times when the cemented-vibrated-head-dblplod concept was used. Apparently, hydraulically fill strength can be substantially increased. Conceptual mining plans are also included on suggested ways of placing and using high-modulus backfills.

Jan 1, 1979

In preparing a paper such as this it was thought that the Newstan Colliery Company Ltd., being comparatively new, would need some introduction to mining people in general.The Newstan Company was formed by the Joint Coal Board in December, 1948 during a period of acute coal shortages. The Company took over the holdings of what were known as the Olstan and Northumberland Collieries, situated at Fassifern, alongside Lake Macquarie and adjacent to the Great Northern Railway, within easy rail access of Sydney and Newcastle, as shown on the locality plan (Fig. 1).The Company was developed in order to produce steaming coal for the power house trade and has continued its activities in the steaming coal trade since its inception. The Olstan and Northumberland collieries were together producing some 300 tons per day when the Company was formed, and it was from this foundation that the colliery was built. The planned development of the Company has been along the lines of producing coal by modern, highly mechanised methods, together with the preparation of theproduct for the consumer, to the highest degree possible consistent with up to date methods.In the comparatively short time of 5t years the mine has developed from a small hand-won coal unit to a high capacity modern mine, one of Australia's largest producers, with an output capacity as high as 3,000 tons per shift.

Jan 1, 1954

By H. Sato, B. Thornton, K. Nishi, A. Usui

"Northwestern Pacific submarine seamounts are believed to be future marine mining areas of ferromanganese crusts, which contain hi-tech industrial metals, such as Co, Ni, Te, Ti, Pt, and REEs. The Takuyo No. 5 seamount is a member of the Cretaceous super-plume seamounts in the north Pacific, located within a Japanese EEZ (100 nm from the Minami- Torishima Is. or Marcus Is.), and only 300 nm away from the Japan’s Licensed area for exploration of Co-rich ferromanganese crusts under the ISA. This is an on-going program supported by independent academic communities but not a state-run program or managed by private funding.We have observed, sampled, measured, and analyzed the occurrences, distribution, physical properties, and microbiological environments at a selected flat topped seamount named Takuyo No.5 as a model area for scientific study of ferromanganese crusts within the Japanese EEZ. We then characterized crust structures, composition, age, and growth history, resulting in an understanding of the overall nature and distribution of these deposits from wide range of areas, water depths and geological environments. The study started with a ROV (Hyper-Dolphin 3K of JAMSTEC) exploration jointly with universities and national institutions (Japan Agency for Marine-Earth Science and Technology, Japan Oil, Gas, and Metal Exploration Corporation, and Geological Survey of Japan) in 2009 using marine geology vessels, remotely-operated vehicle, an oceanbottom drill machine, deep-tow TV camera, as well as conventional dredges and corers. We have been studying the topography, geology, nature of the bottom material of the seamounts using delicate sampling devices and measurement tools, and characterized the distribution patterns of the metal-rich ferromanganese deposits from chemical, mineralogical, and microbiological points of view."

Sep 1, 2014

What is your assessment of the status of the mining industry as we see some evidence of an economic recovery? I am optimistic about the short and midterm prospects for the industry and, hence, for the professionals in the industry that constitute the majority of the SME membership. All who will read this interview recognize that the quality of life we enjoy today is largely a result of our achievements in the mining and minerals processing sectors. I believe that the sustainability of that quality of life and the aspirations of other sectors of the global community to attain that same lifestyle will significantly depend on the continued successes of these industries. Looking at some of the traditional economic indicators, we see predictions of continued increases in gold prices during the next 12 months as a new round of quantitative easing keeps real interest rates low and drives excess capital flows from countries with trade surpluses - who have traditionally parked their money in U.S. government bonds - into other investable assets, such as gold. On the fuel side of the industry, we have during the last decade seen a steady rise in the cost of coal, and some of the recent spot prices have seen dramatic increases. Some suggest that coal prices may rise sooner than anyone expects, as global reserves are revised downward. This is based on the hypothesis that some of the main coal-producing countries are overestimating supplies and that coal prices could start rising far sooner than anyone thinks - with obvious serious implications for energy policy. Those forecasters note that, for the past couple of decades, global supply has been dropping at a faster rate than consumption.

Jan 1, 2011