Search Documents

By G. H. Glos

There was a time when an occasional failure of a tailings embankment was considered an acceptable risk associated with mining activities. This is not the case anymore. A major tailings failure today could result in the indictment of mine officials, huge fines and a possible site closure due to the loss of operating permits. As a result of this changed operational environment, tailings disposal facilities must be operated with these potential consequences in mind. Physical controls for tailings embankments are prohibitively expensive. However, the nuclear industry has developed a system of administrative controls as an alternative to physical controls. Administrative controls may be defined as control of actions, through organizations and management, using written procedures, record keeping, review and audit to assure operation of a facility in a safe manner (10 CFR 50). Administrative controls can reduce the cost of operating tailings impoundments, as well as increase the level of confidence in these facilities.

Jan 1, 1999

By Herty, C. H.

The effect of temperature on the physical properties of structural materials has been the subject of many investigations during the past decade. The literature on the effect of elevated temperatures. is voluminous, and during the last four years a great deal of experimental work has been carried out on the effect of low temperatures on the impact properties of steel. For many engineering purposes it is important to know the shock resistance of steels at low atmospheric temperatures, and with the ever-developing field of refrigeration and separation of materials at low temperatures, the normal limits of atmospheric temperature have been exceeded in practice. Iron and its alloys in the unnotched condition have a high impact strength at low temperatures, but in practice variations in type of notches result either from design or accidentally through scratches and surface or internal defects. A study of notched bar impact tests is, therefore, highly important to the engineer. A survey of the literature on low temperature impact testing indicates that chemical composition, heat treatment and method of testing have been the variables which have been considered in most previous work. In only a few instances has any mention of the steel- making method been mentioned and in these the comparison was between steel-making processes and not between steel-making methods on the same process. In view of the wide variations in impact properties at room temperature, in quench and strain ageing and in grain growth of steels of identical chemical composition, (by this is meant the usual five element analysis reported), it was felt

Jan 1, 1957

By Lok M. Sharma

"Construction of a new bridge in a seismically sensitive area requires careful assessment of earthquake impact on the serviceability of the facility. Not only is the superstructure vulnerable, the foundations play a key role in the bridge’s survivability. A new bridge in eastern part of the state of Missouri in the U.S.A. is located in a seismically active area and hence subject to additional thrust on the foundations and superstructure and potential damage due to liquefaction. An eleven span bridge with foundation soils varying from shallow bedrock to over 30 m (100 feet) overburden soils were considered for the bridge support piers. Two of the bridge support bents located within the flood plain area through over 30m (100 feet) of alluvial deposits were considered most affected by an earthquake event due to the additional thrust and lateral ground spreading. This paper describes the determination of site specific seismic hazard, numerical modelling of the foundation system, and methodology of dynamic analyses, effects of lateral spreading and liquefaction potential on bridge support bents. From numerical modelling using FLAC, the increase in thrust on piers and deformations were computed to predict the behavior of the foundations.INTRODUCTIONA newly constructed bridge on route US 40 crosses the Missouri River west of St. Louis, Missouri and upstream of Mississippi River in mid-west USA. The west abutment area has near surface bedrock while the east abutment area has overburden deposits over 30m (100 feet) thick, mostly river sediments comprising of silts, lean clays and sands overlying bedrock. Softer layers of silts and sands in the east river bank area are assessed to be liquefiable during a high magnitude earthquake event. St Louis area has a potential for a high magnitude earthquake due to the New Madrid Fault some 160km (100 miles) south. The bridge foundations were designed as drilled piers, 2 m (8 feet) in diameter and socketed into the bedrock. Bents No. 10 and 11, located in the lower flood plain area of the river, are considered to be most affected by a seismic event.In order to perform dynamic analyses of the foundations, earthquake ground motion time history was developed for the specific site using a Probabilistic Seismic Hazard Analysis (PSHA) and selecting and scaling of a recorded time history. Relying on the U.S. Geological Survey (USGS) Earthquake Hazard Program for the PSHA and AASHTO Guide Specifications for LRFD Seismic Bridge Design, spectral acceleration values for the site were developed. The spectral acceleration values were for a 7 percent probability of exceedance in 75 years (1000 year return). Numerical modelling using FLAC computer program was performed. This paper presents the seismic design parameters, methodology used in the dynamic analyses, static and dynamic analyses, impact and mitigation of liquefaction on Bents 10 and 11 and the abutment fills, and effect of lateral spreading on the foundations in the lower flood plain area of the bridge. From the numerical modelling, increase in thrusts on pier foundations and estimated deformation were computed."

Jan 1, 2017

By P. R. Day, W. K. Webster

"The introduction of large boreholes underground initially involved taking the techniques of open-pit bench blasting to the production stope, but with deeper boreholes and narrower stopes more controlled techniques must be developed in order to maintain good stope walls and prevent dilution of ore or structural damage to pillars due to blasting overbreak. The points discussed are drilling accuracy and drill pattern, the relationship between open-pit wall control and underground mining, the varied explosives products and initiation devices available, and some of the many ways that variations in loading, such as deck charging, etc., can produce desirable results.IntroductionThe use of large-diameter blastholes for underground mining began ten years ago and today they are widely employed in a variety of orebodies and stope configurations. These big blastholes, which range in size from 4.5 to 8 inches in diameter, were originally employed in the same manner ' as open-pit bench blasts; that is, the stope was silled out to full width and all holes were drilled vertical and parallel. This was suitable for competent, massive orebodies, however the popularity of the big drills saw their usage in more narrow stopes, often with poor ground conditions. The dipping orebodies and small drill sublevels resulted in inclined drilling.Today, there is full-ring drilling of 4.5-inch holes. Some 6.5-inch holes are drilled up to 350 feet deep. A 350-foot borehole may contain 6000 to 7000 pounds of explosive. The detonation of this size of charge weight within the confines of an underground stope can have considerable effect on the stability of stope walls and adjacent pillars. Obviously, precautions must be taken to minimize the damage which would result from the large charge weights possible with these big boreholes."

Jan 1, 1982

By Cadman S. J

( The central part of the Gippsland Basin is surrounded by existing major Petroleum accumulations and although six exploration wells have been drilled in the area, none are significant petroleum discoveries. Post drilling analyses indicate that the wells were drilled off structure due to the presence of high-velocity Miocene channels. These channels contain carbonates of significantly higher interval velocity than the surrounding sediments. Problems with seismic interpretation were thus encountered in the development of prospects in the central part of the Gippsland Basin as part of a BMR prospectivity study. The seismic interpretation problems associated with the Miocene channels are two-way time pull-ups at the underlying top of Latrobe Group and deeper levels on the seismic sections. Interpreted seismic sections passing through some of the exploration wells and the Miocene channels are presented to illustrate the configurations of these channels and the pullup effect associated with them. Two different methods of depth conversion were applied, one for the area below the high velocity channels and the other for the area away from the channel. The application of these two methods of depth conversion were found to be reasonably successful in correcting for the pull-ups caused by the high velocity Miocene channels. Mapping of the events near the top of Latrobe Group and near Base Lower L balmei seismic horizons has led to the identification of several potential structural closures. Further exploration efforts are necessary in this area to test these closures.

Jan 1, 1992

By Jason J. Crowder

Presentation Outline ? Introduction ? Costs of ground support and rehabilitation ? Why post-failure rock mass properties are necessary ? The Rock Mechanics Problem ? Present State of Modelling and Instrumentation in Mining ? Case Study Background ??Williams Mine ? Deriving Parameters for Modelling from Instrumentation ? Results from Case Study ??Back Analyses ? Discussion of Research Impact t Summary

May 1, 2006

Two types of low-sulphidation epithermal mineralisation may be recognised in volcanic terranes. Chalcedonic Silica- Adularia-Illite type mineralisation is most common in rhyolitic terranes, whereas Crystalline Quartz-Illite-(Adularia- Kaolinite) type mineralisation is more typically formed in andesitic terranes. A third type of epithermal mineralisation, the high sulphidation or Vuggy Silica-Alunite- Kaolinite-Illite type, is also common in andesitic terranes. Episodic violent boiling, accompanying hydraulic fracturing and hydrothermal eruptions, characteristic of geothermal systems in rhyolitic terranes, is stressed for the formation of Chalcedonic Silica mineralisation. Such boiling of deeply circulating meteoric groundwater, with some magmatic fluid contribution, provides chalcedonic veining, episodic banding and brecciation textures, adularia stability, bladed calcite, and extreme loss of H2S from the fluid to cause major gold deposition. Crystalline Quartz mineralisation is probably caused by the mixing of shallow acidic groundwater with ascending deep geothermal fluids beneath andesitic strato- volcanoes. The cooling effect, oxidation, and increased acidity, overcomes the dilution effect, and results in quartz deposition, illite (and locally kaolinite) alteration, and precipitation of metals. Extensive formation of base-metal sulphides further enhances gold deposition. Violent boiling is restricted to local structural dilation sites, potentially producing high grade "bonanza" gold mineralisation.

Jan 1, 1991

Arsenic.--Inorganic arsenic has been added to the Environmental Protection Agency's list of hazardous air pollutants because of a high probability it can cause cancer. EPA estimates that inorganic arsenic emissions into ambient air total more than 6,000 tons per year, with about 65;L of this coming from the operations of copper, lead, and zinc smelters. Asbestos Detection.--In June 14, the President signed S. 1658 providing $172.5 million to detect and remove asbestos hazards in schools. Asbestos Use Must be Reported.--All firms using asbestos in the manufacture of some 30 categories of products must describe in detail how they use the mineral to the Consumer Product Safety Commission, for all manufactures since January 1, 1977.

Jan 1, 1980

By Marc C. Bétournay

Hydrogen fuelcells are a known technology, having been applied to stationary (e.g equipment, buildings, power plants) and vehicle applications (e.g transit buses, space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and green house gas emissions. To date, however, fuelcells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuelcells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuelcell type of choice for the industry, the Proton Exchange Membrane, would function at the range of temperatures encountered in underground and surface operations, and use hydrogen that is stored under low pressure and risk. A small fuelcell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, INCO, the Ontario Ministry of Labour, Sandia National laboratories and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter as well as from shock and vibration provided to the unit in underground conditions, at INCO?s 175 Orebody minesite and INCO?s Stobie Mine. The test results provided will show that the unit was not affected by the underground conditions: physically and electrically the unit performed without any reduction in operation or adverse effects imposed.

May 1, 2003

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of copper cementation with zinc in sulphate solution. For copper concentrations of the order of 10 p.p.m., a porous, adherent deposit is formed on the zinc surface and this has a significant influence on the reaction rate. When the specific mass of deposit is less than about O· 35 mg/cm2 the surface may be considered as smooth and the rate is described by simple convective counter diffusion of zinc and copper ions through a laminar diffusion boundary layer to the deposit-solution interface. In the presence of additional deposit, the diffusional mass transfer rate is increased by increased surface roughness.The rate under these conditions is first order, with the degree of enhancement independent of further increases in the specific deposit mass. The enhancement in rateis, however, directly related to the initial mass flux and the species involved in the reaction.Preliminary work showed the same mechanism to apply to cementation from chloride solution, solutions of high zinc concentration, and cementation of copper with iron..

Jan 1, 1970

By Gary Eck, Kevin Tallent

Over the past decades, the science of energetic materials has advanced dramatically in both the fields of military munitions, as well as industrial explosives. Out of necessity, test methods to measure the explosive performance properties of these materials were developed. As would be expected, these test methods have evolved and become more sophisticated with the recent advancements in electronics and computerized technologies.

Jan 1, 1998

By José De Piérola

En los procesos de flotación y lixiviación de la producción de cobre se utilizan aguas recicladas y agua fresca. Este último es un insumo indispensable para ambos procesos, ya que constituye un elemento determinante del volumen de producción, así como un medio de vinculación obligado con el entorno social de las operaciones. En ese sentido, el presente texto describe la utilización del agua- en tanto representa un componente de rentabilidad relacionada al costo, al equilibrio del aprovechamiento con el comportamiento de la fuente y a la sostenibilidad con el entorno social, lo cual implica compartir el agua y recursos económicos para una planificación y adecuada priorización en su asignación.

Sep 9, 2007

By R B. Evans, M G. Townsend

In Northland, New Zealand, localised large deposits of halloysite clay have been produced by in-situ alteration of rhyolite volcanics of Pliocene or Pleistocene age, which were erupted through pre-Pliocene sedimentary strata and locally through Pleistocene basalt; and which were subsequently onlapped by further basalt flows. Alteration to clay has been a result of both hydrothermal and of meteoric processes, and decreases in intensity of alteration with increasing depth. The raw material is crushed and fractionated to produce a product of less than two micron particle size, which is of exceptional whiteness and brightness. The unique properties of the clays render them highly desirable for specialised ceramic purposes.

Jan 1, 1990

By R. J. Colony

DEPOSITS of iron are widely scattered in the folded Cretaceous rocks and the associated igneous intrusives of Puerto Rico. Most of them are too small for commercial development, but a few have aroused some scientific and economic interest, among them the large body of residua] limonite at the west end of the island near Mayaguez1-6 (Fig. 1) and the mixed hematite and magnetite deposit on the southern slopes of the Sierra de Cayey, about four miles north of Arroyo.7-9 Neither of these orebodies has been developed, nor have investigations of the widely distributed deposits of magnetite, which include all the remaining occurrences of iron deserving of economic consideration, proceeded beyond the exploratory stage. With the possible exception of the mixed deposit near Arroyo, the magnetite is directly associated with andesitic and dioritic intrusives, which invade the Cretaceous rock section, and the bulk of it, occurring in calcareous sediments, is clearly of contact-replacement origin. The small deposit on Rio Portugues, north of Ponce, is found in a limestone band near its contact with an andesite dike.10,11 Two deposits of unde-

Jan 1, 1935

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization, and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available? in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number 50241073 by Fenix & Scisson, Inc. to the Denver Mining Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By P. A. Hacquebard, M. P. Avery

"Gondwana coal deposits are widespread and are known to occur in four continents. They are present in Brazil, India, South Africa, and Australia. From coal petrographic examinations and a detailed literature survey, it is interpreted that Gondwana coals are present also in Canada and the United States. Laurasia, or Northern Hemisphere, coals occur in the United States, Canada, and Europe. They form the main coal producing fields of the world. Megascopically, Gondwana coals have a uniform, micro-banded appearance, with a dull lustre; Laurasian coals are bright and have distinct bands of vitrain and clarain. Petrographically, Gondwana coals, compared to Laurasian coals, are lower in vitrinite, but higher in inertinite, particularly in semifusinite. Mineral matter averages 16% in Gondwana coals and 5.7% in Northern Hemisphere coals.Gondwana coals are characterized by thick seams that terminate through lithification (Versteinerung), whereby coal passes laterally into shale. Laurasian coal seams are thinner and terminate by splitting and digitation.Vitrinite/inertinite ratio data indicate deposition of the Gondwana coals in dry marshes under strong oxidizing conditions. The Laurasian coals originated in wet marshes in a reducing environment. As deduced from fossil plants and fossil spores, temperate and near arctic conditions apply for the Gondwana coals. A tropical and subtropical climate is indicated for the Laurasian deposits. The Gondwana coals were formed under allochthonous conditions. They derived from vegetation that drifted into the peat bogs. The Laurasian coals are autochthonous and originated from vegetation that grew and was buried in the peat bogs. The Gondwana coals are Late Carboniferous and Early Permian. The Laurasian coals are entirely Late Carboniferous."

Jan 1, 2004

By G. Weingrill, H. Flachberger, J. Neubacher

The so called Bublon®-process is an innovative process for the controlled expansion of volcanic glasses such as Perlite and for thermal treatment of other minerals. In this manner, functional light fillers with astonishingly altered physical properties can be manufactured. In contrast to conventional Perlite expanding processes no fossil fuels are burned in order to achieve the expansion. Instead, the feed material is heated electrically mainly by radiation based on heat transfer from heating elements. The main advantage is the better controllability of the production process. Therefore, the heating elements are segmented along the flow of the particles, hence in direction of the ongoing expansion. Overheating of the particles, which ultimately leads to the destruction of the particle surfaces and consequently decreasing the quality of the expansion product, can be reduced significantly. Due to flow characteristics and settling behaviors of fines the lower particle size limit of the feed in this process is restricted to not less than 100 µm. Otherwise process instabilities are to be expected. Manufacturing industry demands light and fine hollow microspheres. Therefore, a proven cooperation between Montanuniversität Leoben and Bublon GmbH was formed to develop a new process called ‘Bublite’. This issue was addressed by changing the conveying principle into a pneumatically conveying system transporting particles from the bottom to the top of the kiln by the means of a drag flow. This approach makes it possible to handle the difficult flow patterns in the kiln and to control the retention time of the particles in the heat transfer zone. As a result, it is now possible to expand very fine Perlite particles into a high quality functional lightweight filler with a glazed-closed surface. The dependence of the polymer industry on importing this kind of fillers from overseas can be reduced by producing it close to sites of demand. Also the Perlite mining and processing companies benefit from this technology because the mine lifespan and the output of the processing plant can be increased.

Jan 1, 2018

By Z. H. Zhou

It is difficult to remove cadmium from raw indium using only electrolytic refining because their standard potentials are similar. In this paper, physical and chemical methods were used to remove Cd from raw indium. Indium metal is vacuum refined for two hours at 400°C with a vacuum pressure of 20 Pa. In this process, 99.70% of the Cd can be removed. The removal rate of Cd reaches 90% to 95% when indium is further smelted for 10 minutes in a 20% glycerin solution of KI and I2 at 180°C. When pre-indium is electrolytic refined in an In2(SO4)3-H2SO4 system, in which the indium content is 80 to 100 g/L, the pH is 2.0-3.0 and the current density is 80 to 100 A/m2, the contents of the impurities decrease and the purity of the indium product reaches 99.99%.

Jan 1, 2007

The Pilbara Block is a nucleus of Archaean rocks which lies in the North West Land Division of Western Australia, and it constitutes a mineral province that has been divided into two areas-the West Pilbara Goldfield and the Pilbara Goldfield.In the West Pilbara Goldfield two contemporaneous environments are represented by laterally equivalent volcanic and sedimentary successions which together comprise the Roebourne Group. The two successions are lithologically similar to the classical Warrawoona (volcanic) and Mosquito Creek (sedimentary) successions of the Pilbara Goldfield; but in the West Pilbara Goldfield there is no sign of the erosional break which separates the Warrawoona Succession from the Mosquito Creek succession. The Roebourne Group and the igneous rocks which have intruded it belong to the Archaean Pilbara System.Evidence of preconsolidation movement and igneous intrusion into unconsolidated sediment suggests that tectonism and igneous activity, localized along lines of fracture in an unidentified basement, beganbefore lithification was complete. Movement was primarily vertical, and persisted into the Lower Proterozoic.Vulcanicity and chemical sedimentation, accompanied by a diminution of detr:tal sedimentation, is thought to have caused a relative enrichment in the metal content of the middle part of the Roebourne Group; and the metal may have been remobilized during diagenesis and metamorphism, and localized in zones of dislocation formed both before and after consolidation of the sediments.INTRODUCTIONThe name "Pilbara" has been widely applied in the area under discussion, and to avoid confusion the various uses are summarized below.1. The town of Pilbara, now abandoned, was a centre of mining between 1888 and about 1914. It lies some 90 miles FJSK of Roebourne (Fig. 1).2. The original Pilbara Goldfield was modified several...

Jan 1, 1965

By James J. Olson

This report summarizes the results of a review of foreign coal mining literature conducted under the Bureau's Advancing Coal Mining Technology program. In addition to a discussion on the historical development of mechanized longwall systems, and the current state-of-the-art method in Europe, this report summarizes the previous and ongoing Bureau efforts to adapt longwall technology to U.S. conditions. The bibliographic section of this report, divided into major categories such as mine design, face management, roadway development, strata control, powered roof supports, coal winning, conveying, and automation, contains over a thousand individual entries. The purpose of this report is to provide U.S. mining engineers with background information on longwall methodology and equipment developed in foreign countries (principally Europe). The Bureau of Mines, as part of its Advancing Coal Mining Technology program, is funding R&D projects to demonstrate that the longwall mining method, successfully used in the deep mines of Europe, can boost productivity and improve safety in certain U.S. mines.

Jan 1, 1977