Search Documents

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Khaled Mohamed

Resin-grouted bolts serve as a crucial means of stabilizing yielded coal ribs in underground coal mines. A comprehensive investigation into their efficacy was undertaken by a collaborative effort between the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST). This study involved pull-out tests in multiple locations, including six coal mines and the NIOSH research mine. A total of seventy-three (73) tests were conducted, of wide range of anchorage lengths, ranging from a short encapsulation length of 0.305 m to a fully grouted encapsulation length of 1.524 m. The test findings indicate that when short encapsulation bolts are installed at high rotation speeds, their anchorage capacity is significantly reduced, leading to failure at the bolt-grout interface. Conversely, when these bolts are installed at lower rotation speeds, they exhibit greater capacity, with failure occurring at a higher anchorage load equivalent to the yield load of steel rebar. No matter what the rotational speeds were used during bolt installation in this study, the fully grouted bolts consistently experienced failure at the ultimate load of the steel rebar. Most of the tests carried out on partially grouted bolts with anchorage lengths of 0.610 - 0.914 m have shown behavior patterns like the fully grouted bolts, although exhibiting reduced stiffness. The outcomes of this research offer a profound insight into the ways in which resin-grouted bolts enhance the stability of coal mine ribs.

Feb 1, 2024

By H. B. Miller

Contract Incentives have long been employed in the underground hardrock industry as a tool to influence employee performance, enhance productivity, and control labor costs. While traditionally structured to establish a direct correlation between performance and compensation, many contract programs have evolved into elaborate systems that promote strategies often viewed as independent of productivity. This paper presents the findings of research into these contract incentives and was conducted with the cooperation of 33 mines utilizing a spectrum of employee compensation and incentive programs. Emphasis of this analysis focuses on the types of production contracts observed and their role with respect to employee earnings.

Jan 1, 1994

By William H. Wiese

Anecdotal reports of high rates of congenital malformations and spontaneous abortions at the Shiprock Indian Health Service Hospital in San Juan County, New Mexico prompted an interview survey, obtaining data from families of 26 former uranium miners and 30 controls. Results supported the possibility of increased fetal wastage and congenital malformations. However, definitive conclusions were obviated by methodologic limitations in terms of selection of cases and controls and interviewing technique, as well as very low numbers and lack of statistical significance. The Council of Environmental Quality (1980) published a report which singled out San Juan County, nationally, as having an extra-ordinary high rate of congenital anomalies reported from birth certificates in the years 1973-75. San Juan County is in the northwest corner of New Mexico and includes the northeastern edge of the Navajo Indian Reservation. It has been the site of uranium mining and milling and also of coal mining (Clement Associates, 1980). While much attention has been focused on lung cancer and chronic lung disease as health hazards to uranium miners, virtually no attention has been focused upon possible reproductive effects that may result from exposure to radiation. Could these reports indicate such an additional arena of health effect either on miners or on others living in the vicinity of the mines and mills? The biologic and epidemiologic literature does not lend much support for adverse genetic outcome. The UNSCEAR report (UNSCEAR, 1977) summarizes much of the existing data. For example, on the basis of many animal studies and what has been observed in atom bomb survivers in Japan, it has been estimated that mutation rates resulting from low LET radiation to paternal germ cells would be 60 X 10-6 recessive and 20 X 10-6 dominant mutations per gamete per rad. There would be a five-fold increase in the number of recognizable abortions. The doubling dose for genetic disorders in mice is estimated at 100 rads. The assumption has been that low levels of exposure, such as might be received occupationally from uranium mines and mills or environmentally will produce reproductive effects that would defy distinction from background rates. However, the possibility can not be dismissed. In man, spermatogonia are thought to be three-fold more sensitive than in the mouse. Also, the high LET radiation from alpha particles is as much as 20-fold more effective in inducing changes in meiotic and post meiotic stages of cells, compared with low LET radiation. There is some degree of localization of alpha emitters in testicular tissue after inhalation of radon and radon daughters (Blanchard, R.L. and Moore, J.B., 1971; Pohl, E., 1964). The slopes of doseeffect curves are affected by type radiation and rate of administration. Data on such curves are poorly defined and debated as to whether there may be increased or decreased effect per unit dose at low levels of high LET radiation. Increased rates of aberrations of chromosomes in peripheral lymphocytes cultured from uranium miners have been reported (Brandom, W.F., et al., 1978). At cumulative exposures of 100 working level months (WLM) or less, a range of exposure lower than the limit of current occupational standards, the aberrations were increased more than two-fold. Our interest has led us to pursue the question of reproductive effects along three separate paths of inquiry: studies of the secondary sex ratio, cytogenetic study of human sperm, and studies of rates of congenital anomalies. I will present the thrust of our findings, most of which remain preliminary, comment on their interpretation and limitations, and indicate directions needed for future research. The secondary sex ratio is the ratio of males to females at birth. In the U.S., the ratio averages around 1.05. Ratios in blacks are somewhat lower (1.025) than in whites (1.053). For American Indians, the data are less definite. Values from Oklahoma and California are similar to whites (1.05). Southwestern tribes have, as we shall see, varying levels. The theoretical effects on sex ratio resulting from irradiation of the zygote are based on the principles of sex-linked genetics, including differential effects of lethal dominant and recessive mutations on the sex chromosomes, complicated by possible non-disjunctional events. Observations have done little to clarify, confirm or refute the theories. The sex ratio of progeny of survivers of the atomic bomb showed little change (Schull, W.J., Otake, M., and Neel, J.V., 1981). Observations in children of uranium miners having been inconsistent. Most frequently cited is a study of miners in Czechoslovakia (Müller, C., Razicka, L., and Bakstein, J., 1967). Compared with children born to miners prior to the start of mining, the sex ratios of children born after the start of mining were decreased -statistically significant after correcting for birth order. The ratios in first-born children were, before the start of mining, 1.118, and, after the start of mining, .713. In the interview survey at Shiprock, the sex ratio in families of non-miners was 1.03, and in families of miners it was 0.73 (p < .05). Dr. Alan Goodman at the University of New Mexico has studied trends in the sex ratio in the general population in New Mexico and Arizona with particular reference to counties in the Four Corners area and the Navajo Indian Reservation, areas where uranium mining has been active_ His findings (unpublished) are as follows: (1) Beginning in the early 1950&apos;s, there has been a modest, but persistant and statistically significant decline in the secondary sex ratio for the state of New Mexico compared with the U.S., a decline that roughly parallels the emergence of uranium mining in the Grants mineral belt in northwestern New Mexico. (2) Data available for the 11 years since 1969 show that among the five counties with ratios significantly lower than the state

Jan 1, 1981

By María Justiniani

Además de los pasivos ambientales mineros que a la fecha oscilan entre los 6900 y 70001 a nivel nacional, existen otras unidades mineras que corren el riesgo de quedar abandonadas o ser paralizadas de forma definitiva, incrementando el patrimonio minero inactivo. Al respecto, su falta de atención, su gestión deficiente y los escenarios limitados que existen para su tratamiento, comprometen seriamente el desarrollo sostenible que se exige para todas las actividades y etapas vinculadas a la minería. En ese escenario, se deben evaluar otras alternativas que permitan un mejor aprovechamiento de dicho patrimonio, que sostenga equilibradamente el desarrollo económico, la protección ambiental y la promoción social.

Sep 29, 2023

By John S. Civetta, Seth Martin, Marc J. Gallagher, Arthur J. Alzamora, Ronald Peralta

The Crown Building, built circa 1921, is a 26-story iconic building located at West 57th Street and Fifth Avenue in the heart of Manhattan. The paper highlights collaboration between the geotechnical engineer and foundation contractor to develop economical and practical solutions to foundation design and construction challenges associated with this complex redevelopment project. The project includes both below-grade and above-grade expansion of the occupied building, and required undermining the existing foundations, and essentially doubling the foundation loads. The below-grade expansion required surgical foundation work including drilling minicaissons, shoring columns, underpinning, and excavating 20 feet of rock.

By H Yuan, H Tian, Y Zhang, Z Wang, C Wang

Submerged arc welding (SAW) is one of the significant metal-joining processes for manufacturing marine vessels, steel pipes, and offshore structures with high deposition rate and engineering reliability. Welding flux serves several essential functions, including atmospheric shielding, arc stabilisation, bead morphology control and weld metal (WM) refinement. Therefore, from a thermodynamic point of view, the focus for flux design and WM compositional/microstructural modification has been placed to elucidating the transfer pathways and mechanisms of major alloying elements, such as Si, Mn, Ti and O during welding. To this end, a thermodynamic model has been established to predict alloying element contents in the WM. Such functions are enabled by the physicochemical properties of the fluxes, which are inherently rooted in the nature of the fluxes. A unique yet systematical investigation, including physicochemical property changes and structural evolution behaviours, has been conducted over the wide range of fluxes applied to actual welding of EH36 shipbuilding steels. Combined with spectroscopic methods, structural behaviours of network formers such as SiO2, Al2O3 and TiO2 and network modifiers such as MgO, MnO and CaO have been illustrated. Viscosity and ionic conductivity have been found to be positively associated with the degree of polymerisation.

Aug 21, 2024

By R. W. Diamond

Introduction THE Sullivan mine and the milling, smelting, and refining operations of the Consolidated Mining and Smelting Company are sufficiently well known to make unnecessary anything more than a very brief account of the events which led up to this Company&apos;s branching out into the chemical industry. This development is the result of the 26 per cent sulphur content of the Sullivan ore. Seventy-five to eighty per cent of this sulphur enters the mill tailing, which is stocked at Kimberley. The remainder, contained in the lead and zinc concentrate, is burned off in the first treatments at Trail. Prior to this new development, the sulphur gas was wasted to the atmosphere. In spire of its great dilution with air and discharge from stacks at high elevations above the plant, some damage to vegetation close to the plant was experienced. It had always been apparent that this sulphur should be recovered and utilized if possible, at the same rime relieving, or curing, the smoke nuisance, and constant studies with this in view had, therefore, been maintained. One of the early conclusions reached was that the Canadian prairies would ultimately require large quantities of phosphate fertilizers, as had been the experience of older countries, and that these fertilizers would constitute a large outlet for sulphuric acid which could be made from smelter gases. This conclusion prompted a widespread search for phosphate rock, particularly in British Columbia and western Alberta, with the result that low-grade beds were discovered in the Crowsnest district and to the north therefrom through extensive areas (1). Following these discoveries, an experimental plant was built at Trail for the production of triple superphosphate in order to facilitate field-tests in fertilizing prairie lands.

Jan 1, 1934

By K. B. Han, S. Winkler, M. J. Benoit, M. J. Worswick

"Automotive heat exchangers are fabricated by forming multi-layered aluminum (Al) alloy brazing sheets into the desired geometry and subsequently passing the assembly through a furnace for brazing. As manufacturers seek to use thinner gauge and higher strength sheet to reduce vehicle weight, forming of the Al alloy sheets has become a challenge. Warm forming has previously proven to allay these forming concerns, but no consideration was given to the effect of increasing the forming temperature on brazing. Recently, it was shown that annealed sheet was more susceptible to the detrimental phenomenon of liquid film migration (LFM) during brazing if formed above 150°C, while work hardened sheets showed no increased susceptibility to LFM with increasing forming temperature, up to 250°C. In the current study, the brazing performance of simulated battery cooling plates was investigated. The plates were fabricated both from fully annealed and work hardened sheets. Brazing was assessed by microstructural evolution during a brazing cycle. The post-brazed microstructure varied with strain and forming temperature in plates made from annealed sheets, while no variation in microstructure with location or forming temperature was observed in plates formed from work hardened sheets.INTRODUCTION Since the 1970’s, one common method of fabricating automotive heat exchangers has been by forming multi-layered aluminum (Al) alloy sheets, and subsequently brazing the formed components together in a controlled atmosphere furnace. The Al alloy sheets used are comprised of at least two Al alloys roll bonded together, but can consist of additional layers, depending on the application; at minimum, the sheets are comprised of a core and clad layer. The core layer, often an AA3xxx alloy, remains solid throughout processing and provides strength to the assembly. The clad layer is always one of the AA4xxx series alloys which, due to their high silicon (Si) content, have a melting temperature range well below that of the core alloy. When the sheet is passed through the brazing furnace, the clad alloy melts to provide the brazed joint filler metal throughout the assembly, while the core alloy remains solid. In order to achieve cost and weight savings, heat exchanger fabricators have used Al alloy sheets with reduced thickness. However, deformation and brazing of these increasingly thin components remains a concern (Zhao & Woods, 2013). Furthermore, springback has been observed after forming sheets of higher initial strength (i.e. work hardened conditions), leading to flatness issues of formed components. Consequently, the ability to form high quality brazed joints is difficult in components formed from higher strength brazing sheets."

Jan 1, 2018

By Frank Haehnig, Kurt Kogler

"With a height of 200 m, a crown width of 626 m and a concrete volume of 1.6 million m³, the Kölnbrein Dam in the upper Malta valley in Carinthia / Austria is the largest concrete dam in Austria. Boasting a storage capacity of 200 million m³ with a received water load of 54 MN, this is one of the strongest arch dams in the world.During its construction from 1974 to 1977, the dam was equipped with a comprehensive monitoring system capable of comparing developing deformations and stresses with the design values.With a planned reservoir level of 1,900 m a.s.l. the dam saw the reservoir level of 1,860 m a.s.l. breached in the year 1978. This led to extremely high seepage losses of up to 200 ltr/sec and a rise in the foundation water pressure up to 100% of the dam’s height. These observations were caused by the development of horizontal cracks in the area of the middle dam blocks, between the lowest inspection walkway and the waterside.As a consequence, power plant operations had to significantly be reduced and a number of additional measures were carried out – though these did not lead to the desired sealings.The developer subsequently decided that the dam should undergo a general rehabilitation from 1998 to 1994 in accordance with a concept developed by Professor Lombardi. This concept involved erecting a 50 m high support structure with a concrete volume of 500,000 m³ on the airside of the dam, along with the addition of neoprene bearings to transfer 1.2 million tons of the horizontal load. These measures were able to reduce the deformations in the dam enough so that mostly load-bearing injections into the cracks in the dam’s concrete could successfully be carried out by way of targeted grouting measures using injection resin (RODUR) specifically developed for this purpose.In the years 1998 - 1994, a total of 130,000 m of grouting, monitoring and control drillings were executed, and around 200,000 kg of synthetic resin was injected into the cracks in the dam’s concrete.These measures have ensured the dam‘s uninterrupted operation since 1994. A number of small re- injections were again carried out on the contact surface in the years 2011 and 2012."

Jan 1, 2016

By D. Meadows, P. Carrato, E. Wingate, K. Churchill

Extracting lunar ice, to be processed into pure water or hydrolyzed into oxygen and hydrogen, faces many challenges. On the Moon icy-regolith deposits that contain up to 10% water are found within Permanently Shadowed Regions (PSR) at both lunar poles, where temperatures approach -220 ⁰C. NASA has identified several technology gaps that exist in developing these resources including: • Excavating large quantities of icy-regolith • Delivering large quantities of acquired resources • Hardware that is lightweight and energy efficient • Hardware that is reliable and durable. NASA uses public challenges to incentivize innovative approaches to closing these gaps. The Break the Ice Lunar Challenge provides over three million dollars in prize money to teams that compete in developing solution to mining the Moon. This paper describes the rules for this challenge and presents some of the proposed solution.

Feb 1, 2023

By P Gomez, R Baumgartner, G Escobar

"The Cerro Corona mine consists of a Cu-Au porphyry deposit located in the Andes of northern Peru. The deposit comprises a typical Cu-Au multiphase porphyry mineralisation that has been overprinted by an epithermal event. This has generated a complex pattern of argillic alteration facies, which was accompanied by a locally structural-controlled Au-Cu mineralisation with the presence of gold and limited Cu sulfides and sulfosalts. These features, along with the porphyry-style mineralisation, produced a multifaceted occurrence of gold.Since the beginning of operations at Cerro Corona in 2008 there has been a continuous improvement of the geological and mineralogical knowledge. All mineralogical studies have mainly focused on host rock types and, to a lesser extent, alteration minerals, but little work has been done on the mineralisation itself. As a consequence, limited mineralogical information was available for use in the process optimisation initiatives.In the last two years, a series of mineralogical characterisation studies were undertaken with two main goals. First, to gain an understanding of the mineralisation genesis and second, to obtain a detailed characterisation of copper and gold minerals to support ongoing process optimisation. The first goal was achieved by conventional optical microscopy while the second required electronic microscopy and other microanalyses due to the necessity of quantifying several minerals of interest for the processing.The results were used to refine pre-existing geometallurgical domains, explain copper and gold losses in the flotation process and to some extent, improve copper and gold recoveries. The mineralogical characterisation is an ongoing work. Mineralogy provides the basis for any optimisation exercise since it looks in detail at the material to be treated and therefore, should be part of all geometallurgical programs.CITATION:Baumgartner, R, Gomez, P and Escobar, G, 2016. Comprehensive Mineralogical Characterisation at the Cerro Corona Cu-Au Porphyry Mine – the Fundamental Key for Geometallurgical Applications, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 221–230 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Ralphie Adams, Tiana Rasmussen, Ashley E. Shirer

Transmission line foundation designers must rely on limited subsurface information, from easily accessible locations, resulting in subsurface uncertainty, increased design risk and increased construction costs. This paper presents a different approach for foundation analysis conducted in mountainous and alluvial floodplains located northwest of Phoenix, AZ. The region is dominated by fault-bounded, northeast dipping mountain ranges, where rock types and drillability can vary from granite to intact basalt. The valleys between are comprised of “basin-fill” deposits ranging from conglomerates and cemented soils to lose alluvium. Recently deposited alluvial fills can vary in depth significantly from location to location due to erosion and deposition from active and historic hydraulic features. To limit the subsurface uncertainty for foundation design, a phased approach using geophysical surveys along with detailed geologic reconnaissance was employed. Both compression wave and shear wave velocities were measured in order to identify the depth and properties of loose erodible materials from more scourresistant cemented, conglomerate, and rock deposits. These analyses were used in combination with limited subsurface drilling and sampling to evaluate direct embedment steel pole foundations for over fifty structures. Post analysis results from limited construction drilling reports were used to assess this approach.

Sep 8, 2021

By T. E. Oates, W. Spiteri

In 2015, after amendments to the explosives regulations, stemming became a mandatory activity for all South African mining operations. There are, however, circumstances in which it is thought stemming has an adverse impact on the blasting outcome. Some of these circumstances include blasting in hot holes, in reactive ground, or when blasting a pre-split. In order to determine when stemming is necessary, its role in the control of adverse blasting phenomena and impact on explosive performance were reviewed. Stemming was found to play a significant role in the fragmentation process and burden movement. Additionally, stemming significantly influences the control of flyrock, air-blast, and toxic fume generation. The review of the literature indicates some motivation for not using stemming for presplit, trim, hot hole, and reactive ground blasting, provided the benefits associated with not stemming the holes outweigh the risks of stemming them. Best practice for stemming from the literature indicates a stemming length of 0.7 × burden is best for larger hole diameters, and 20 to 30 × Ø for smaller hole diameters. Crushed aggregate appears to be the most effective stemming material. The South African explosives regulations pertaining to stemming were found to be consistent with those of Australia and the USA.

Aug 1, 2021

By Roland Kammel

For electrolytic recovery of silver from dilute aqueous solutions improved mass transfer is necessary to achieve favourable current efficiencies and high space-time yields. The many cell designs proposed for this application can be divided into two different groups: cells from which the silver must be redissolved and cells from which the deposit can be reclaimed as a metal. Introduction Electrolytic silver recovery methods have proven advantageous under technical and economic aspects for the treatment of rinse water, still rinses and spent silver solutions in the electroplating and surface finishing industry, of exhausted fixing baths from photographic processing, bleed electrolytes from silver refining processes and leach liquors. Examples of the compositions of typical dilute silver solutions are listed in Table I.

Jan 1, 1984

By W. S. Dyer

The Minto coal basin lies in the central part of the province of New Brunswick, near the head of Grand Lake. The village of Minto which is the centre of mining activity of the district, lies about 35 miles east of Fredericton and somewhat greater distances to the north and west of the cities of St. John and Moncton respectively. Although coal has been mined in the basin for a number of years, it was not until recently that the production became sufficient to warrant a thorough geological investigation. The summer of 1922 was spent, in accordance with in structions from the Director of the Geological Survey, in making a detailed study of the geology and coal resources of the Minto coal basin, which is covered by the Minto and Chipman map sheets, each embracing an area of 200 square miles. The present paper is a short outline of the principal results obtained in the field. The writer wishes to acknowledge the assistance cheerfully given him by the managers and officials of the various companies operating in Minto. He wishes especially to thank Mr. W. B. Evans, Manager of the Rothwell Coal Company, for assistance in the collection of fossils and for the generous supply of information relative to the early history of the coal field.

Jan 1, 1924

By R. Fukuzawa

"The objective of this research is to evaluate the magnitude of carbon prices required to drive process development and innovation for the global nickel industry in a direction that tackles the multifaceted sustainability challenges that the industry faces, including air pollution reduction and greenhouse gas abatement. The results suggest that the currently considered carbon prices are not sufficient to drive innovations in processing methods or upstream pollution prevention. The co-benefits of climate change mitigation and pollution prevention cannot be readily realized under climate change policy alone. Increased coordination between climate change policy and performance-based environmental legislation is necessary. INTRODUCTIONNickel is an important metal in our modern society as it is used in stainless steel, alloys, electroplating and rechargeable batteries, all of which are integral to our economic growth and development (Eckelman, 2010).However, nickel production is energy intensive and therefore susceptible to emerging climate change policies, which may lead to production curtailment and/or increased unit costs of production unless changes in efficiency or energy sources are made (Mudd, 2010). The industry is faced with multi-faceted constraints: future technology must not only deal with metallurgical, financial and environmental constraints but also promote low energy and low carbon practices. This presents a challenge for this industry where technology innovation, development and commercialization are often lengthy, risky and costly processes (Imrie, 2006).Climate change is one of the many challenges faced by our society. Others include other pollution to air, water and land, resources shortage and economic development. From a policy perspective, it is important to balance multiple and often competing needs in an integrated manner. It would require some levels of trade-off in order to maximize the overall effectiveness but also to ensure that one policy does not undermine other policy objectives.The aims of this study are to evaluate how developments in climate change policy would affect the nickel industry in the context of existing environmental regulations and how the industry could respond under these constraints."

Jan 1, 2012

"The pressure leaching of alkali-pretreated limonitic laterite ore in nitric acid was studied. The optimal leaching conditions are as follows: leaching temperature of 458 K, initial nitric acid of 2.44 mol/L, leaching time of 60 min, liquid to solid ratio of 2:1 mL/g, agitation speed of 500 RPM. Under the above conditions, the extraction of nickel and cobalt can be achieved as approximate 95% and 80% respectively while that of iron is as lower as 1%. The leaching residue containing 70% of iron in the form of hematite and trace amount of chromium is suitable as the raw material for iron-making. The nitric acid in the leaching solution can be regenerated and further recycled to leach. INTRODUCTIONIt has been estimated that 60%-70% of the world land-based nickel resources presented in nickel laterites containing 130 million tons of nickel although these only accounted for about 42% of the world nickel production (Sudol, 2005; Luo et al., 2010). The nickel resource of laterite has not yet been fully utilized. Due to the increasing global demand of nickel and the declining global reserves of nickel sulphides, there is an increasing focus on the processing of the huge reserves of laterite ores today. Nickel laterite ores can be simply divided into two types, namely, silicate-rich and limonite. The former can be treated effectively by pyrometallurgical process in which the ferronickel product or nickel/iron sulphide matte is produced (Monhemius, 1987). The limonitic laterite is rich in iron in the form of goethite which is the main nickel-bearing mineral and usually contains cobalt associated with a manganese phase (Chang et al., 2010; Georgiou and Papangelakis, 2004). The limonitic laterite is usually processed by hydrometallurgical methods, such as atmosphere acid leaching (AL) (Xu et al., 2005; McDonald and Whittington, 2008), high pressure acid leaching (HPAL) (Chou et al., 1977; Georgiou and Papangelakis, 1998; Rubisov et al., 2000; Whittington and Muir, 2000) and reductive roasting-ammonia leaching (Caron Process) (Whittington and Muir, 2000; Valix and Cheung, 2002). The AL process can proceed at lower temperature, thus the operation costs may be very low. But two biggest problems associate with the AL process, namely, the slow rates of nickel extraction and potentially the significant amount of impurities such as iron and aluminum in the leaching solutions, which hampers the wide application of the AL process. The Caron Process uses the pyrometallurgical and hydrometallurgical methods together to obtain the metallic values, but the overall metal recovery is relatively low, especially for cobalt. In recent years, the environment-friendly process of HPAL has become increasingly important because it is most suitable for low-grade ores and leads to high extraction of the valuables. However, the HPAL process needs a much higher temperature and pressure (503-533 K, 4-5 MPa) to maintain a relatively fast leaching rates, which results in higher operation costs. Moreover, another serious problem of scale formation in autoclaves occurs in the HPAL process, for example, in Moa Bay, up to 20 cm scale may build up resulting in 5 days descale downtime per month. In addition, the iron residues cannot be utilized for ironmaking due to the presence of high content chromium (Ema and Harada, 1987; Owada and Harada, 1987; Takagi and Furui, 1987)."

Jan 1, 2012

By A. Podlesny, E. N. Rubinstein, J. J. Sammarco, B. Demich

Roof bolting typically follows the extraction of a commodity to help keep the roof from collapsing. During 2004 to 2013, roof bolter operators had the highest number of machinery-related injuries, accounting for 64.7 percent, at underground coal mines. This paper analyzes U.S. roof bolter fatal and nonfatal lost-time injury data at underground work locations for all commodities from 2004 through 2013 and determines risk indices for six roof bolting tasks. For fatal and nonfatal incidences combined, the roof bolting tasks in order of the highest to lowest risk index were bolting, handling of materials, setting the temporary roof support (TRS), drilling, tramming, and traversing. For fatalities, the roof bolting tasks in order of the highest to lowest risk index were handling of materials, setting the TRS, bolting, drilling, traversing, and tramming. Age was found to be a significant factor. Severity of injury, indicated by days lost, was found to increase with increasing age as well as with increasing experience, largely due to the confounding of age and experience. The operation of the roof bolting machine used in underground mining should be a research priority given the high frequency and severity of incidents. The results also suggest that temporal factors may exist, so additional research is warranted to better understand these factors and potentially develop interventions. This research provides a datadriven foundation from which future research can be conducted for safety interventions to reduce the frequency and severity of incidences involving the roof bolter activities of bolting, handling of materials, and setting the TRS.

Jan 1, 2016

By Randy Wheeler

One of the more difficult topics to address concerns the effects of vibration on historic structures. Not only blast induced vibration, but also vibration from other transient and semi-continuous sources like, traffic, human activity, and environment forces. A common question might be, “What level of blast-re l a ted PPV is considered safe?” A review of some of the papers available from the ISEE Explosives Reference Database on CD ROM shows that 0.50 inch per second was often used. It was not clear on what basis this value was selected except that it represents the low frequency limit for plaster developed by the United States Bureau of Mines in RI 8507. In another case, a limit of 0.20 inch per second was mentioned, apparently simply because it was ten times less than 2.00 inches per second.

Jan 1, 2004

By G. E. Rencken, J. H. Potgieter, A. Narain, J. Smith

To conserve fresh water resources and comply with environmental regulations, DRDGOLD, a South African gold producer re-treating surface tailings, has transitioned to a fully closed water circulation system. Consequently, the accumulation of contaminants, as well as addition of reagents, has led to changes in water composition that have compromised leach performance and overall gold recovery. A two-sample t-test confirmed a significant difference in gold recoveries between the use of Rand Water, which was used as a benchmark, and untreated process water. Atomic absorption analysis of ERGO’s process water, confirmed the presence of iron, nickel, zinc, and manganese. A study of the effect of the identified contaminants on gold recovery showed that iron, nickel, and zinc have the largest negative effect on gold recovery, with iron and nickel being more detrimental than zinc. Sulphates were shown to have a possible passivation effect, which also influenced gold recoveries, although to a lesser extent than the heavy metals. Calcium, when present in excess, had a positive influence on gold recovery indicating the possible formation of a calcium aurocyanide complex. Lime softening successfully reduced the heavy metal and sulphate concentrations, and the gold recoveries obtained with the treated process water were similar to those as achieved with Rand Water.

Jul 1, 2021