Search Documents

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations within a multiple-seam configuration. A comparative study was performed at two separate mine sites. The objective of this study was to compare two mines, each affected by this pillar load transfer mechanism, and to show how this interaction affected underground workings by the installing and monitoring underground instrumentation. At mine site A where the overburden was 1,000 ft, the innerburden thickness was less than a pillar width (40 to 45 ft), overlays of the mine layout show pillars were not superpositioned, excessive roof to floor convergence was measured, and pressure readings indicated pillar core loading only. At mine site B, the overburden was approximately 555 ft, the innerburden thickness was approximately 105 ft, overlays of the mine layout show pillars were superpositioned, minimal roof to floor convergence was measured, and pressure readings indicated a skin loading only.

Jan 1, 1988

By Alfonso Ballón

Dado que las aguas pertolantes crean problemas en las operaciones de concentración de menas, se buscó un tratamiento selectivo de flotación por el cual pase la blenda(obtenida de yacimientos de cobre y zinc) separada del cobre. Empero, este proceso tiene dificultades porque no hay diferenciación de sus superficies cristalinas y los sulfuros de cobre son confundidos con los de zinc. Por ello, el objetivo del presente trabajo es mostrar las pruebas realizadas que permitan asegurar una perfecta activación de la blenda contenida en la mixtura, asi como una mejor separación del cobre y el zinc, entre otras, reuniendo las condiciones necesarias para su aplicación con el sulfato de cobre.

Jun 20, 1954

By J. Y. Kim

Lead ions originating from galena during processing of complex sulphide ores migrate to "cover" the surface of sphalerite and iron sulphide mineral particles, and cause poor selectivity in differential flotation. Generally in sulphide ore processing, the lead-activated minerals float in the Cu/Pb rougher circuit. Subsequently, surface lead complicates the zinc flotation circuit by lowering the concentrate grade due to the co-flotation of lead-activated iron sulphide minerals. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zn and Pb-Zn ores is discussed. Plant and laboratory test data are interpreted by determining the surface composition of individual grains of sphalerite and iron sulphide particles using two surface analytical techniques, Laser Ionization Mass Spectrometer (LIMS) and Time of Flight-Secondary Ion Mass Spectrometer (TOF-SIMS). Cationic and anionic species on the surface were analyzed to elucidate the phenomena.

Jan 1, 1995

By Leonard Obert

The investigation reported herein is concerned with the generation and propagation of the strain wave produced in rock by the detonation of a high-velocity explosive. This report is the second of a series that will deal with this and related problems. The rock type in which these experiments were carried out was greenstone. Subsequent reports will discuss similar investigations in other rock types. Specifically, the problem under study is concerned with how certain characteristics of the strain wave, such as the maximum compressive and tensile strain, the maximum time rate of change of strain, the frequency components present in the pulse, the duration of the pulse, and other measurable characteristics, vary with the size of the charge and the distance from the detonation point to the point of measurement. . Other investigators have studied certain aspects of the generation and propagation problem in rock. However, in these studies the travel distances from the detonation to measurement point were comparatively long and the frequency components in the explosive wave were usually under 100 c.p.s. In this study the detonation to measurement distance covered. the range from 2 to 54 feet, and the strain gages and recording equipment employed in the instrumentation of the problem had a frequency response range from 200 to 10,000 c.p.s.

Jan 1, 1950

By Thomas C. Denton

ALL of the 45 political divisions of Africa were accessible to non-Communist world industry and commerce throughout 1964, although in some of them revolt and political attitudes presented problems. The position of the continent as a whole for mineral and mineral fuel resources, production, and oversea exports continued to improve. At yearend, significant quantities of a greater number of mineral commodities vital to industry and agriculture were being produced than in any other continent. This statement excludes Communist areas on other continents but might well hold true even if such areas were included. Deriving from its exceptionally diversified production, Africa furnished overseas industrialized countries as a w ole a greater variety of key mineral commodities than any other area. In addition, the value of mineral imports from Africa into the United Kingdom and continental non-Communist Europe probably exceeded the value of such imports from any other area if gold is included and mineral fuels excluded.

Jan 1, 1966

By M. Potesser

After the primary or secondary lead production the bullion lead is remelted and charged into a vessel with following refining process. The removing of arsenic, antimony and tin takes place by salt slags or oxidizing gases like air or pure oxygen. Due to the increasing lead price, Messer Austria GmbH in cooperation with the institute of Nonferrous Metallurgy at the University of Leoben have developed a new process named OXIPOT for the refining of tin, arsenic and antimony. The OXIPOT process is in principle based on purging technology with a ceramic or steel purging device. This leads to an increased retention time of the refining products due to the deeper bath level and an optimized specific reaction volume concerning the bubble size. This paper describes the process, pilot plant, and thermodynamic calculations for the optimization concerning the selectivity of element removal.

Jan 1, 2008

By Liu Xinghua

Yuanjiacun iron ore located in Shanxi province of China has finely disseminated grain size and contains refractory iron-bearing silicate gangue minerals such as chlorite. Therefore, a large amount of secondary slime (the content of -10µm fraction was up to 32.92%) was produced inevitably in fine grinding process, and chlorite was also enriched in concentrate from the content of 4.3% to 14.8% after high intensity magnetic separation. These two characteristics result in the difficulty to deal with Yuanjiacun iron ore by flotation. In this test work, contrast tests between single reverse flotation and selective flocculation desliming-reverse flotation were conducted on Yuanjiacun iron ore. The test results show that after selective flocculation desliming, the iron grade of cationic reverse flotation concentrate increases by 6.15% and the recovery increases by 7.25%; the iron grade of anionic reverse flotation concentrate also increases by 2.15%. Furthermore, analyses of grain size composition and mineral composition were carried out on separation products, the results indicate that selective flocculation desliming plays a dual role of optimizing grain size composition of flotation feed and removing iron-bearing silicate gangue minerals (chlorite) effectively.

Sep 1, 2012

By Marvin S. Seppanen

Computer programers are often required to make modifications to unfamiliar Fortran routines. This Bureau of Mines report describes a computer program designed to aid the programer in such a situation by reorganizing: Fortran routines. This reorganization includes a sequential renumbering of the routine's statement numbers, a sequential renumbering, and relocation of format statements, an alphanumeric reordering of dimensioned and typed variables, a uniform pattern of text spacing, and a sequential numbering of the records in the final Fortran routine. The computer program has been extensively tested by the author and has proved to be a valuable tool for reorganizing Fortran routines developed under contract and later utilized by the Bureau, and for preparing routines for publication.

Jan 1, 1975

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

In currently used mining methods, blasting techniques often causes dilution of valuable ore and results in costly processing requirements. In the context of narrow vein mining of thin and highly concentrated orebodies there is a need of a mining method that can reduce dilution in order to remain economically viable. This research project explored the viability of a new mining technology, thermal fragmentation, in narrow vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation, as well as for an existing method used for narrow vein mining; comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs, as well as increased productivity and ore recovery, meant that the new method would improve the financial performance of any operation. These results identify that there is an opportunity to introduce the thermal fragmentation technology to narrow vein mines within Australia, in order to lower costs and increase profit.

By Graham W. Marks, Betsy M. Jones

"Recently4/ it was shown that the total energy method5/ of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing this work, the present report deals with analyses for beryllium, zinc, cadmium, and indium.There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved.As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is associated with zinc and cadmium in zinc ores.The authors wish to acknowledge the valuable assistance of the staff of the Bureau of Mines Analytical Laboratory who made the chemical analyses and supplied the ore samples used in this work.A brief description of the procedures followed in making the standard curves and analyses is given below; a detailed discussion will be found in an earlier paper.6/Basically, the procedure for determining a standard curve consists of two parts: (1) Choosing a suitable line in the spectrum of the element to be determined and (2) determining the variation in the intensity of this line with the amount of the element burned in the arc."

Nov 1, 1948

By T. R. Kostecki

"Instrumented rock bolts are effective tools for assessing the reinforcement and condition of immediate roofs; however, instrumentation can have relatively high costs, which can be justified by high reliability and repeatable and representative data measurements. The instrument’s durability and operational life are of great importance, along with accuracy, applicability, and usefulness. This paper develops reliability models for three instrumentation technologies used in slotted rebar, drawing data from studies at five underground coal mines. Three case studies demonstrate instrument applicability and usefulness. Finally, two types of instrumented rock bolts are used to determine the direction of bend and maximum bending strain. RÉSUMÉ Les boulons d’ancrage instrumentés sont des outils performants qui permettent d’évaluer la consolidation et la condition des toits immédiats. L’instrumentation peut cependant se révéler très onéreuse, des coûts qui se justifient par sa fiabilité élevée ainsi que par des mesures de données reproductibles et représentatives. La durabilité de l’instrument et sa durée de vie opérationnelle sont très importantes, de même que son exactitude, son applicabilité et son utilité. En s’appuyant sur des données issues d’études menées dans cinq mines de charbon souterraines, cet article développe des modèles de fiabilité pour trois technologies d’instrumentation utilisées pour des barres d’armature nervurées. Trois études de cas démontrent l’applicabilité de l’instrument et son utilité. Enfin, deux types de boulons d’ancrage instrumentés sont utilisés pour déterminer la direction de la flexion et la contrainte de flexion maximale.INTRODUCTION Using instrumented rock bolts to monitor strain changes in a rock bolt array allows engineers to understand the per-formance and effectiveness of the rock reinforcement system and the response of the rock mass to such support; however, instrumentation remains a niche solution for solving complex ground-control problems—particularly for underground coal mines, which is where they are needed most. From 2000 to 2016, fall-of-ground fatalities still accounted for an average of approximately 30% of the total annual underground coal mine fatalities in the United States alone (United States Department of Labor, 2018). These tools would also be useful for deep hard-rock mining conditions. The main reasons for the lack of widespread use are not only cost but also accuracy, applicability, implementation procedures, intrinsic permissibility, and reliability (Peng, 2015). As a result, measurements of coal mine roof behaviour using instrumented rock bolts are quite scarce, not widely published, or inadequately presented to provide a seamless understanding of a roof’s response to support."

Jan 1, 2018

By T. F. Curry, L. B. Berger, H. A. Watson, S. J. Pearce

The conduct of work at elevated air pressures , such as in caissons and in tunnel - driving in subaqueous strata , poses safety problems not encountered in mining and tunneling operations at ordinary atmospheric pressure . This publication discusses some of the problems involved and presents information on the following subjects : ( 1 ) Physiological effects of gases at elevated pressure . ( 2 ) Use of respiratory protective equipment in rescue or recovery operations in event of fire or other emergency in pressurized tunnels . ( 3 ) Effect of elevated pressure on performance of some gasdetecting instruments ; interpretation of the results . Various types of respiratory protective devices are discussed in relation to their possible use at elevated pressures , especially the 2 - hour , selfcontained , recirculating - oxygen - breathing apparatus , which has had wide use in the United States during rescue and recovery work in the mining industry . A modified procedure that eliminates the hazard of oxygen poisoning enabling the safe use of this apparatus at elevated pressures , up to 45 pounds per square inch , gage , and tests to verify its practicability are described . procedure involves control of the partial pressure of oxygen in the breathing

Jan 1, 1964

By W. H. Young

In response to increasing national energy requirements. highlighted by the continuing growth in demand for coal for the generation of electric power the output of bituminous coal and lignite in 1965 passed the 500-million-ton mark for the first time since 1956, thus emphasizing the steady up-ward trend from the recent low of 403 million tons in 1961. There were corresponding upward trends in consumption, exports mechanization, and productivity. Production.-The output of bituminous coal and lignite in the United States in 1965-512 million tons-was 5 percent greater than the 487 million tons produced in 1964. The gain was attributed largely to expanded consumption by the electric utilities, greater use at coke ovens, and an increase in exports.

Jan 1, 1967

By Jack O. Jones

The Furnish mine, Caharrus County, W. C., was operated intermittently until 1905 as a gold mine. Scheelite was discovered by A. L. Mash in the mine dumps of the Furniss and Phoenix mines, and he later informed the Bureau of Mines of his discovery. The Bureau of Mines, in two projects at the deposit in 1948 and in drilled 12 holes totaling 1,706.6 feet, examined and sampled the underground workings, excavated by bulldozer and hand, 3,155 linear feet of trenches and collected numerous samples for assay. The best scheelite shown; was found in the underground exposure of the Furniss mine.

Jan 1, 1950

By R. L. Crosby, L. W. Higley

Magnesium- rich magnesium- aluminum- zirconium alloys in the cast and in the extruded and heat- treated condition were studied to identify the phases present and to determine phase distribution . In cast alloys , two intermetallic compounds were identified : ZrAla by X- ray diffraction ; and Mg₁ Al₁₂ by microscopical observation . Based on microscopical comparisons between the known phases in the cast structures and the phases in the structures of extruded and heat - treated rods , ZrAl₂ and Mg1 , Al12 were identified in the structure of the latter . The presence of these intermetallic compounds in rod specimens could not be confirmed by X- ray diffraction . ZrAl₂ was observed in the structure of extruded and heat - treated rod specimens containing as little as 0.01 weight - percent zirconium . The presence of aluminum restricts the solubility of zirconium in magnesium because of the strong tendency to form ZrAla . This intermetallic compound segregated in clusters of small particles in the matrix of cast alloys , and only slight improvement in distribution was noted when the alloying techniques were varied .

Jan 1, 1964

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received' little study on the part of wire mills, particularly those that have commenced operations in the last few years.

Jan 1, 1930

By R. R. M. Cousens, W. S. Garrett

SYNOPSIS The paper gives a background to the water hazards of the so-called West Wits Line and refers to some geological aspects of the Wonderfontein Valley in which the West Driefontein mine property lies. It describes the precautions taken against flooding during shaft sinking, development and stoping; these include cover hole drilling with cementation, provision for water storage in worked-out areas, installation of water tight bulkhead doors and pumping capacity well in excess of the mine's normal requirements. The plan of campaign adopted after the inrush took place is explained and the reorganization and expansion of pumping arrangements are discussed. When it became clear that the only means of saving the mine was to construct plugs to isolate the inrush while still maintaining all emergency pumping measures, the work was put in hand with the utmost dispatch. In considering the design of the plugs a number of major factors had to be taken into account. The most vital was the need for speed which was complicated by difficulty of access to the plug sites because of the huge volumes of water flowing in the drives. How this and other factors affecting plug design and construction, leakage problems, sequence of operations and final closure of the valves, were overcome is detailed in the paper. INTRODUCTION The inrush of water into the West Driefontein mine, the biggest gold producer in the world, which began on 26th October, 1968 and continued unabated for 23 days before the flood was stemmed, was unprecedented in the history of mining. Also unprecedented were the tremendous efforts and organization which made it possible to bring the situation under control and so save the mine from being lost for a matter of years. BACKGROUND Before going into details of how the situation was brought under control it is appropriate to consider the background to the event. The water problem on the so-called West Wits Line has been recognized for many years. As far back as 1912 the Pullinger Shaft, situated in the centre of what is now the Venterspost mine property, had to be abandoned because there were no means then available of coping with the large quantity of water encountered. To appreciate what vast quantities of water were involved, it helps to refer to some geological aspects of the Wonderfontein valley in which the West Driefontein property lies. The narrow tabular Witwatersrand gold-bearing beds, which dip at about 25 degrees towards the south, are overlain by a surface layer of dolomite which reaches a maximum thickness of some 4,000 ft at West Driefontein. A number of vertical syenitic dykes intersect the valley more or less at right angles to its course (Fig. 1). These dykes are about 150 ft thick on average and are spaced at about eight-mile intervals in the West Driefontein area. They penetrate both the dolomite and the Witwatersrand beds and as they are impervious to water they divide the valley into a series of large underground water compartments.

Jan 5, 1969

By Ralf Plinninger, Pafos Busch, Richard Gradnik

This paper presents the details of the Bad Bergzabern tunnel project. This tunnel is the main part of the B427 federal road bypass, intended to improve the regional traffic infrastructure and to reduce the traffic load in the historic city centre of the health resort Bad Bergzabern. Located in the south-western part of Germany, the project area is situated at the eastern margin of the so-called Palatinate Forest, a low mountain region of mainly triassic sediments with a complex and variable geological history. The German federal government, represented by the office of mobility of Rhineland- Palatinate, awarded the contract to BeMo Tunnelling, a specialized Tunnelling company with a long history of innovation and success in NATM tunnelling. The contract includes the construction of two separate tubes with a length of approximately 1,44 km (0.9 mi)—the road (main) tunnel with a cross section of 101 m2 (1,090 sq ft) and a parallel rescue tunnel with a cross section of ca. 23 m2 (250 sq ft.) Both are connected by six cross passages. Tunnels and cross passages are excavated according to the principles of the New Austrian Tunnelling Method (NATM). Due to BeMo Tunnelling’s technical expertise and capabilities, the project team was able to engineer a speed-up concept that saves money and time for the construction team and client. This paper presents the innovative approach BeMo Tunnelling made to optimize the execution of the tunnelling works and the challenges the project team is facing with regard to a complicated geological situation, countermeasures against an increasing effect of climate change and volatile prices for construction materials.

Jun 13, 2023

This Bureau of Mines publication presents five papers given at a Technology Transfer Seminar on Metal Mine Fire Protection Research. Several seminars are held each year to bring the latest results of Bureau conducted and sponsored research to the attention of the mining industry as quickly as possible.

Jan 1, 1977

By Ronaldo Adriano Alvarenga Borges

A produção de aço com baixo teor de enxofre é de extrema importância para a indústria naval e de tubos para a indústria de petróleo. Porém, a fabricação destes aços acarreta um maior desgaste do revestimento refratário das panelas de transporte/tratamento de aço das aciarias devido às condições operacionais mais severas (maiores tempos de processo, maiores temperaturas, adições de fluxantes de escória, etc.) exigidas durante o processamento destes aços. Neste trabalho é apresentado o modelamento estatístico do impacto da fabricação deste tipo de aço, via rota de tratamento metalúrgico de dessulfuração de aço, na campanha refrataria (vida) das panelas conjuntamente com a análise post-mortem de tijolos refratários da linha de escória de uma das panelas. O modelamento levou em consideração os dados de 6 meses de operação da aciaria de uma usina integrada com capacidade de 4,5 Mt/ano. A análise dos resultados revelou que os altos tempos de tratamento no refino secundário, especialmente utilizando o forno panela como equipamento de dessulfuração, a adição de compostos fluxantes de escórias contendo sódio, como nefelina, são os principais fatores que degradam a vida do refratário de tais panelas. Palavras-chave: Refratários; Dessulfuração de aço; Desgaste de panela; Nefelina.

Aug 17, 2017